Frame Wire
Components
COMPONENTS
ILLUSTRATION
*1 |
BATTERY SERVICE HOLE COVER |
*2 |
SERVICE PLUG GRIP |
ILLUSTRATION
*1 |
CONNECTOR COVER ASSEMBLY |
*2 |
ENGINE ROOM MAIN WIRE |
![]() |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
ILLUSTRATION
*1 |
REAR UNDER COVER |
*2 |
REAR UNDER SIDE COVER LH |
*3 |
REAR UNDER SIDE COVER RH |
*4 |
REAR SEAT CUSHION LEG SUB-ASSEMBLY |
*5 |
REAR SEAT CUSHION ASSEMBLY |
*6 |
REAR DOOR SCUFF PLATE LH |
*7 |
REAR DOOR SCUFF PLATE RH |
*8 |
REAR SEAT CUSHION LOCK HOOK |
*9 |
REAR CENTER SEAT OUTER BELT ASSEMBLY |
- |
- |
![]() |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
● |
Non-reusable part |
ILLUSTRATION
*1 |
NO. 1 FLOOR UNDER COVER |
*2 |
CENTER NO. 2 FLOOR HEAT INSULATOR |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
- |
- |
ILLUSTRATION
*1 |
HV FLOOR UNDER WIRE |
*2 |
NO. 1 HV BATTERY COVER PANEL RH |
*3 |
TRANSMISSION CONTROL CABLE ASSEMBLY |
*4 |
BATTERY COVER LOCK STRIKER |
![]() |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
- |
- |
Installation
INSTALLATION
PROCEDURE
1. INSTALL HV FLOOR UNDER WIRE
CAUTION:
Be sure to wear insulated gloves.
(a) Insert the HV floor under wire into the floor panel hole and engage the grommet. |
![]() |
(b) Install 2 new clamps in the order shown in the illustration. |
![]() |
(c) Install the nut. Torque: 8 N·m {82 kgf·cm, 71 in·lbf} |
![]() |
(d) Install the 2 nuts and new clamp in the order shown in the illustration. Torque: 8 N·m {82 kgf·cm, 71 in·lbf} |
![]() |
(e) Install the nut. Torque: 8 N·m {82 kgf·cm, 71 in·lbf} |
![]() |
(f) Connect the HV floor under wire connector.
(g) Engage the clamp.
(h) Install the 2 nuts. Torque: 8 N·m {82 kgf·cm, 71 in·lbf} |
![]() |
(i) Install the HV floor under wire with the 2 nuts. Torque: 8 N·m {82 kgf·cm, 71 in·lbf} |
![]() |
2. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
(a) Connect the transmission control cable assembly to the vehicle body with the 2 nuts.
Torque:
6 N·m {61 kgf·cm, 53 in·lbf}
3. INSTALL CENTER NO. 2 FLOOR HEAT INSULATOR
(a) Install the center No. 2 floor heat insulator with the 3 nuts.
Torque:
5 N·m {51 kgf·cm, 44 in·lbf}
4. INSTALL NO. 1 FLOOR UNDER COVER
Click here ![]()
5. INSTALL EXHAUST MANIFOLD
Click here ![]()
6. INSTALL FRONT EXHAUST PIPE ASSEMBLY
Click here ![]()
7. CONNECT HV FLOOR UNDER WIRE
CAUTION:
Be sure to wear insulated gloves.
(a) Connect the shield ground to the HV battery.
(b) Connect the 2 HV battery junction block assembly connectors.
NOTICE:
Make sure that the connectors are connected securely.
8. INSTALL NO. 1 HV BATTERY COVER PANEL RH
Click here ![]()
9. INSTALL REAR SEAT CUSHION LEG SUB-ASSEMBLY
Click here ![]()
10. INSTALL REAR UNDER COVER
Click here ![]()
11. INSTALL REAR UNDER SIDE COVER LH
Click here ![]()
12. INSTALL REAR DOOR SCUFF PLATE LH
Click here ![]()
13. INSTALL REAR UNDER SIDE COVER RH
Click here ![]()
14. INSTALL REAR DOOR SCUFF PLATE RH
HINT:
Use the same procedure as for the LH side.
15. INSTALL REAR SEAT CUSHION LOCK HOOK
Click here ![]()
16. INSTALL REAR SEAT CUSHION ASSEMBLY
Click here ![]()
17. CONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY
Click here ![]()
18. CONNECT HV FLOOR UNDER WIRE
Click here ![]()
19. CONNECT ENGINE ROOM MAIN WIRE
CAUTION:
Be sure to wear insulated gloves.
NOTICE:
Do not allow any foreign matter or water to enter the inverter with converter assembly.
(a) Connect the inverter with converter assembly connector and move the lock lever to lock them. NOTICE:
|
![]() |
20. INSTALL SERVICE PLUG GRIP
Click here ![]()
21. INSPECT FOR EXHAUST GAS LEAK
If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.
(a) Perform "Inspection After Repair" after repairing an exhaust gas leak.
Click here ![]()
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during HV floor under wire removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/ReplacedReplaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
| *: When performing learning using the Techstream. Click here |
|||
Auxiliary battery terminal is disconnected/reconnected |
Perform steering sensor zero point calibration |
Lane departure alert system (w/ Steering Control) |
|
Pre-collision system |
|||
Intelligent clearance sonar system* |
|||
Lighting System (for HV Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking assist monitor system |
||
Panoramic view monitor system |
|||
|
Inspection After Repair |
|
|
CAUTION:
- Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.
Click here

- To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.

- To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

- To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here ![]()
PROCEDURE
1. REMOVE SERVICE PLUG GRIP
Click here ![]()
2. DISCONNECT ENGINE ROOM MAIN WIRE
CAUTION:
Be sure to wear insulated gloves.
NOTICE:
Do not allow any foreign matter or water to enter the inverter with converter assembly.
(a) Move the lock lever while pushing the lock on the connector, and disconnect the inverter with converter assembly connector. NOTICE:
|
![]() |
3. REMOVE CONNECTOR COVER ASSEMBLY
Click here ![]()
4. CHECK TERMINAL VOLTAGE
Click here ![]()
5. TEMPORARILY INSTALL CONNECTOR COVER ASSEMBLY
Click here ![]()
6. DISCONNECT HV FLOOR UNDER WIRE
Click here ![]()
7. DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY
Click here ![]()
8. REMOVE REAR SEAT CUSHION ASSEMBLY
Click here ![]()
9. REMOVE REAR SEAT CUSHION LOCK HOOK
Click here ![]()
10. REMOVE REAR DOOR SCUFF PLATE LH
Click here ![]()
11. REMOVE REAR UNDER SIDE COVER LH
Click here ![]()
12. REMOVE REAR DOOR SCUFF PLATE RH
HINT:
Use the same procedure as for the LH side.
13. REMOVE REAR UNDER SIDE COVER RH
Click here ![]()
14. REMOVE REAR UNDER COVER
Click here ![]()
15. REMOVE REAR SEAT CUSHION LEG SUB-ASSEMBLY
Click here ![]()
16. REMOVE NO. 1 HV BATTERY COVER PANEL RH
Click here ![]()
17. DISCONNECT HV FLOOR UNDER WIRE
CAUTION:
Be sure to wear insulated gloves.
(a) Disconnect the 2 HV battery junction block assembly connectors. NOTICE: Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector. |
|
(b) Disconnect the shield ground from the HV battery.
18. REMOVE FRONT EXHAUST PIPE ASSEMBLY
Click here ![]()
19. REMOVE EXHAUST MANIFOLD
Click here ![]()
20. REMOVE NO. 1 FLOOR UNDER COVER
Click here ![]()
21. REMOVE CENTER NO. 2 FLOOR HEAT INSULATOR
(a) Remove the 3 nuts and center No. 2 floor heat insulator. |
![]() |
22. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
(a) Remove the 2 nuts and disconnect the transmission control cable assembly. |
![]() |
23. REMOVE HV FLOOR UNDER WIRE
CAUTION:
Be sure to wear insulated gloves.
NOTICE:
Insulate the disconnected connectors with insulating tape.
(a) Remove the 2 nuts. |
![]() |
(b) Remove the 2 clamps.
NOTICE:
If the clamps are removed forcibly, the stud bolts may be damaged.
(c) Disengage the grommet and pull out the HV floor under wire from the floor panel hole. |
![]() |
(d) Remove the 3 nuts. |
![]() |
(e) Remove the 2 nuts and clamp. NOTICE: If the clamp is removed forcibly, the stud bolt may be damaged. |
![]() |
(f) Disengage the clamp. |
![]() |
(g) Disconnect the HV floor under wire connector.
(h) Remove the nut and HV floor under wire.


















