Engine Coolant Temperature Sensor
Components
COMPONENTS
ILLUSTRATION
*1 |
COOL AIR INTAKE DUCT SEAL |
*2 |
ENGINE COOLANT TEMPERATURE SENSOR |
*3 |
INLET AIR CLEANER ASSEMBLY |
*4 |
NO. 2 ENGINE COOLANT TEMPERATURE SENSOR |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
Inspection
INSPECTION
CAUTION:
- Do not put your hands into the water that has been heated for the inspection.
- Touching the heated water could result in burns.
PROCEDURE
1. INSPECT ENGINE COOLANT TEMPERATURE SENSOR
(a) Measure the resistance according to the value(s) in the table below. Standard Resistance:
NOTICE: If checking the engine coolant temperature sensor in water, be careful not to allow water to contact the terminals. After checking, wipe the water off the engine coolant temperature sensor. If the result is not as specified, replace the engine coolant temperature sensor. |
|
2. INSPECT NO. 2 ENGINE COOLANT TEMPERATURE SENSOR
(a) Measure the resistance according to the value(s) in the table below. Standard Resistance:
NOTICE: If checking the No. 2 engine coolant temperature sensor in water, be careful not to allow water to contact the terminals. After checking, wipe the water off the No. 2 engine coolant temperature sensor. If the result is not as specified, replace the No. 2 engine coolant temperature sensor. |
|
Installation
INSTALLATION
PROCEDURE
1. INSTALL ENGINE COOLANT TEMPERATURE SENSOR
HINT:
Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.
Click here ![]()
(a) Apply a light coat of engine coolant to the O-ring of the engine coolant temperature sensor.
(b) Install the engine coolant temperature sensor to the water outlet with a new clip.
NOTICE:
- If the engine coolant temperature sensor has been struck or dropped, replace it.
- If reusing the engine coolant temperature sensor, be sure to inspect the O-ring.
- Make sure that the O-ring is not cracked or moved out of place when installing the engine coolant temperature sensor.
(c) Connect the engine coolant temperature sensor connector.
2. INSTALL CONVERTER WITH INVERTER ASSEMBLY
Click here ![]()
3. INSTALL NO. 2 ENGINE COOLANT TEMPERATURE SENSOR
(a) Apply a light coat of engine coolant to the O-ring of the No. 2 engine coolant temperature sensor.
(b) Install the No. 2 engine coolant temperature sensor to the radiator pipe with a new clip.
NOTICE:
- If the No. 2 engine coolant temperature sensor has been struck or dropped, replace it.
- If reusing the No. 2 engine coolant temperature sensor, be sure to inspect the O-ring.
- Make sure that the O-ring is not cracked or moved out of place when installing the No. 2 engine coolant temperature sensor.
(c) Connect the No. 2 engine coolant temperature sensor connector.
4. INSTALL INLET AIR CLEANER ASSEMBLY
Click here ![]()
5. INSTALL COOL AIR INTAKE DUCT SEAL
Click here ![]()
6. ADD ENGINE COOLANT (for Engine)
Click here ![]()
7. INSPECT FOR COOLANT LEAK (for Engine)
Click here ![]()
8. PERFORM INITIALIZATION
(a) Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.
Click here ![]()
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during engine coolant temperature sensor removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/ReplacedReplaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
| *: When performing learning using the Techstream. Click here |
|||
Auxiliary battery terminal is disconnected/reconnected |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
Pre-collision System |
|||
Intelligent Clearance Sonar System* |
|||
Lighting System (for HV Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking Assist Monitor System |
||
Panoramic View Monitor System |
|||
Replacement of inverter with converter assembly |
Resolver learning |
|
|
Replacement of ECM |
Perform Vehicle Identification Number (VIN) registration |
MIL illuminates |
|
Replacement of engine coolant temperature sensor |
Inspection after repair |
|
|
PROCEDURE
1. DRAIN ENGINE COOLANT (for Engine)
Click here ![]()
2. REMOVE COOL AIR INTAKE DUCT SEAL
Click here ![]()
3. REMOVE INLET AIR CLEANER ASSEMBLY
Click here ![]()
4. REMOVE NO. 2 ENGINE COOLANT TEMPERATURE SENSOR
(a) Disconnect the No. 2 engine coolant temperature sensor connector. |
![]() |
(b) Remove the clip and No. 2 engine coolant temperature sensor from the radiator pipe. NOTICE: If the No. 2 engine coolant temperature sensor has been struck or dropped, replace it. |
![]() |
5. REMOVE CONVERTER WITH INVERTER ASSEMBLY
Click here ![]()
6. REMOVE ENGINE COOLANT TEMPERATURE SENSOR
(a) Disconnect the engine coolant temperature sensor connector. |
![]() |
(b) Remove the clip and engine coolant temperature sensor from the water outlet. NOTICE: If the engine coolant temperature sensor has been struck or dropped, replace it. |
![]() |






