Battery Voltage Sensor
Components
COMPONENTS
ILLUSTRATION
*1 |
UPPER HV BATTERY COVER SUB-ASSEMBLY |
*2 |
BATTERY VOLTAGE SENSOR |
*3 |
NO. 1 HV BATTERY SHIELD PANEL |
- |
- |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
- |
- |
Installation
INSTALLATION
PROCEDURE
1. INSTALL BATTERY VOLTAGE SENSOR
CAUTION:
Be sure to wear insulated gloves and protective goggles.
(a) Install the battery voltage sensor to the HV battery with the bolt. Torque: 7,5 N·m {76 kgf·cm, 66 in·lbf} NOTICE:
|
|
(b) Connect the battery voltage sensor connector.
NOTICE:
Make sure that the connector is connected securely.
2. INSTALL NO. 1 HV BATTERY SHIELD PANEL
CAUTION:
Be sure to wear insulated gloves and protective goggles.
(a) Pull back the rear No. 1 HV battery shield and install the No. 1 HV battery shield panel to the HV battery.
(b) Install the bolt and nut.
Torque:
7,5 N·m {76 kgf·cm, 66 in·lbf}
(c) Connect the battery voltage sensor connector.
(d) Engage the clamp.
3. INSTALL UPPER HV BATTERY COVER SUB-ASSEMBLY
CAUTION:
Be sure to wear insulated gloves and protective goggles.
(a) Install the upper HV battery cover sub-assembly to the HV battery with the 8 bolts and 4 nuts.
Torque:
7,5 N·m {76 kgf·cm, 66 in·lbf}
4. INSTALL HV BATTERY
Click here ![]()
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during battery voltage sensor removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/ReplacedReplaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedures not Performed | Link |
|---|---|---|---|
| *1: When performing learning using the Techstream. Click here |
|||
Auxiliary battery terminal is disconnected/reconnected |
Perform steering sensor zero point calibration |
Lane departure alert system (w/ Steering Control) |
|
Pre-collision system |
|||
Intelligent clearance sonar system* |
|||
Lighting System (for HV Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking assist monitor system |
||
Panoramic view monitor system |
|||
Replacement of HV battery |
Battery status info update |
HV battery status information cannot be updated |
|
CAUTION:
- Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.
Click here

- To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.

NOTICE:
- After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here

- The type of battery voltage sensor to be used varies depending on the vehicle model.
- The type of battery voltage sensor can be confirmed by the color of the label.
*a
Blue Label
- If the wrong type of battery voltage sensor is installed, the power switch cannot be turned on (READY).
- After installing the battery voltage sensor, perform the following to check that the power switch can be turned on (READY).
- Turn the power switch on (READY).
- Turn the power switch off and wait for 30 seconds or more.
- Turn the power switch on (READY) again.
PROCEDURE
1. REMOVE HV BATTERY
Click here ![]()
2. REMOVE UPPER HV BATTERY COVER SUB-ASSEMBLY
CAUTION:
Be sure to wear insulated gloves and protective goggles.
(a) Remove the 8 bolts, 4 nuts and upper HV battery cover sub-assembly from the HV battery. |
|
3. REMOVE NO. 1 HV BATTERY SHIELD PANEL
CAUTION:
Be sure to wear insulated gloves and protective goggles.
(a) Disengage the clamp. |
![]() |
(b) Disconnect the battery voltage sensor connector.
(c) Remove the bolt and nut. |
![]() |
(d) Pull back the rear No. 1 HV battery shield and remove the No. 1 HV battery shield panel from the HV battery.
*1 |
No. 1 HV Battery Shield Panel |
*2 |
Rear No. 1 HV Battery Shield |
![]() |
Pull Back |
4. REMOVE BATTERY VOLTAGE SENSOR
CAUTION:
Be sure to wear insulated gloves and protective goggles.
(a) Disconnect the battery voltage sensor connector. NOTICE: Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector. |
![]() |
(b) Remove the bolt and battery voltage sensor from the HV battery. NOTICE: If the battery voltage sensor has been struck or dropped, replace it. |
![]() |







