Engine Coolant Temperature Sensor 1 Circuit Short to Battery or Open (P011515). Throttle / Pedal Position Sensor / Switch "A" Circuit Short to Ground (P012011). Throttle / Pedal Position Sensor / Swit
Engine Coolant Temperature Sensor 1 Circuit Short to Battery or Open (P011515)
DESCRIPTION
Refer to DTC P011511.
Click here ![]()
HINT:
When DTC P011515 is stored, the ECM enters fail-safe mode. During fail-safe mode, the engine coolant temperature is estimated to be 80 °C by the ECM. Fail-safe mode continues until a pass condition is detected.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
P011515 |
Engine Coolant Temperature Sensor 1 Circuit Short to Battery or Open |
The engine coolant temperature sensor output voltage is higher than 4.91 V for 0.5 seconds or more (1 trip detection logic). |
|
Comes on |
DTC stored |
SAE Code: P0118 |
HINT:
When this DTC is output, check the engine coolant temperature in the Data List. Enter the following menus: Powertrain / Engine / Data List / Coolant Temperature.
DTC No. | Coolant Temperature | Malfunction |
|---|---|---|
P011515 |
-40°C (-40°F) |
|
If the Data List values is normal it may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.
MONITOR DESCRIPTION
The engine coolant temperature sensor is used to monitor the engine coolant temperature. The engine coolant temperature sensor has a thermistor with a resistance that varies according to the temperature of the engine coolant. When the coolant temperature is low, the resistance in the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are reflected in the output voltage from the sensor. The ECM monitors the sensor voltage and uses this value to calculate the engine coolant temperature. If the engine coolant temperature sensor output voltage deviates from the normal operating range, the ECM interprets this as a fault in the engine coolant temperature sensor circuit and stores this DTC.
Example:
If the engine coolant temperature sensor output voltage is higher than 4.91 V for 0.5 seconds or more, the ECM store this DTC.
MONITOR STRATEGY
Related DTCs |
P0118: Engine coolant temperature sensor range check (high voltage) |
Required Sensors/Components (Main) |
Engine coolant temperature sensor |
Required Sensors/Components (Related) |
- |
Frequency of Operation |
Continuous |
Duration |
0.5 seconds |
MIL Operation |
Immediate |
Sequence of Operation |
None |
TYPICAL ENABLING CONDITIONS
Monitor runs whenever the following DTCs are not stored |
None |
All of the following conditions are met |
- |
Battery voltage |
8 V or higher |
Engine switch |
On (IG) |
Starter |
Off |
TYPICAL MALFUNCTION THRESHOLDS
Engine coolant temperature sensor voltage [Engine coolant temperature] |
Higher than 4.91 V [Less than -59°C (-74°F)] |
CONFIRMATION DRIVING PATTERN
HINT:
- After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here

- When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here

- Connect the Techstream to the DLC3.
- Turn the engine switch on (IG).
- Turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the engine switch off and wait for at least 30 seconds.
- Turn the engine switch on (IG) [A].
- Turn the Techstream on.
- Wait 0.5 seconds or more [B].
- Enter the following menus: Powertrain / Engine / Trouble Codes [C].
- Read the pending DTCs.
HINT:
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
- Enter the following menus: Powertrain / Engine / Utility / All Readiness.
- Input the DTC: P011515.
- Check the DTC judgment result.
Techstream Display
Description
NORMAL
- DTC judgment completed
- System normal
ABNORMAL
- DTC judgment completed
- System abnormal
INCOMPLETE
- DTC judgment not completed
- Perform driving pattern after confirming DTC enabling conditions
HINT:
- If the judgment result is NORMAL, the system is normal.
- If the judgment result is ABNORMAL, the system is malfunctioning.
- [A] to [C]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- When clearing the permanent DTCs, do not disconnect the cable from the battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.
WIRING DIAGRAM
Refer to DTC P011511.
Click here ![]()
HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
READ VALUE USING TECHSTREAM (CHECK FOR OPEN IN WIRE HARNESS)
*1 |
Engine Coolant Temperature Sensor |
*2 |
ECM |
*a |
Front view of wire harness connector (to Engine Coolant Temperature Sensor) |
- |
- |
(a) Disconnect the engine coolant temperature sensor connector.
(b) Connect terminals 1 (E2) and 2 (THW) of the engine coolant temperature sensor connector on the wire harness side.
(c) Connect the Techstream to the DLC3.
(d) Turn the engine switch on (IG).
(e) Turn the Techstream on.
(f) Enter the following menus: Powertrain / Engine / Data List / Coolant Temperature.
Powertrain > Engine > Data ListCoolant Temperature
(g) According to the display on the Techstream, read the Data List.
OK:
Techstream Display | Specified Condition |
|---|---|
Coolant Temperature |
Higher than 135 °C |
HINT:
Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.
Click here ![]()
| OK | REPLACE ENGINE COOLANT TEMPERATURE SENSOR |
|
CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
(a) Disconnect the engine coolant temperature sensor connector.
(b) Disconnect the ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
C41-2 - C56-101 (THW) |
Always |
Below 1 Ω |
C41-1 - C56-133 (ETHW) |
Always |
Below 1 Ω |
C41-2 or C56-101 (THW) - Other terminals |
Always |
10 kΩ or higher |
| OK | REPLACE ECM |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
Throttle / Pedal Position Sensor / Switch "A" Circuit Short to Ground (P012011)
DESCRIPTION
The throttle position sensor is built into the throttle body with motor assembly and detects the opening angle of the throttle valve. This sensor is a non-contact type sensor. It uses Hall-effect elements in order to yield accurate signals even in extreme driving conditions, such as at high speeds as well as very low speeds.
The throttle position sensor has 2 sensor circuits, VTA1 and VTA2, each of which transmits a signal. VTA1 is used to detect the throttle valve angle and VTA2 is used to detect malfunctions in VTA1. The sensor signal voltages vary between 0 V and 5 V in proportion to the throttle valve opening angle, and are transmitted to the VTA1 and VTA2 terminals of the ECM.
As the valve closes, the sensor output voltage decreases and as the valve opens, the sensor output voltage increases. The ECM calculates the throttle valve opening angle according to these signals and controls the throttle actuator in response to driver inputs. These signals are also used in calculations such as air fuel ratio correction, power increase correction and fuel-cut control.
HINT:
- When throttle position sensor DTCs are output, check the throttle valve opening angle using the Techstream. Enter the following menus: Powertrain / Engine / Data List / Throttle Position Sensor No.1 Voltage and Throttle Position Sensor No.2 Voltage.
- Throttle Position Sensor No.1 Voltage is the VTA1 signal, and Throttle Position Sensor No.2 Voltage is the VTA2 signal.
Reference (Normal Condition):
When Accelerator Pedal Fully Released
When Accelerator Pedal Fully Depressed
(Engine Running)
Throttle Position Sensor No.1 Voltage (VTA1)
Throttle Position Sensor No.2 Voltage (VTA2)
Throttle Position Sensor No.1 Voltage (VTA1)
Throttle Position Sensor No.2 Voltage (VTA2)
0.6 to 1.1 V
2.1 to 3.1 V
3.2 to 4.8 V
(Not fail-safe)
4.6 to 4.98 V
(Not fail-safe)
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
P012011 |
Throttle / Pedal Position Sensor / Switch "A" Circuit Short to Ground |
The output voltage of VTA1 is less than 0.56 V for 2 seconds or more (1 trip detection logic). |
|
Comes on |
DTC stored |
SAE Code: P0122 |
MONITOR DESCRIPTION
The ECM uses the throttle position sensor to monitor the throttle valve opening angle. If the VTA1 terminal voltage is less than the threshold, the ECM will illuminate the MIL and store this DTC.
MONITOR STRATEGY
Related DTCs |
P0122: Throttle position sensor 1 range check (low voltage) |
Required Sensors/Components (Main) |
Throttle position sensor |
Required Sensors/Components (Related) |
- |
Frequency of Operation |
Continuous |
Duration |
2 seconds |
MIL Operation |
Immediate |
Sequence of Operation |
None |
TYPICAL ENABLING CONDITIONS
Monitor runs whenever the following DTCs are not stored |
None |
All of the following conditions are met |
- |
Battery voltage |
8 V or higher |
Engine switch |
On (IG) |
Starter |
Off |
TYPICAL MALFUNCTION THRESHOLDS
VTA1 voltage |
Less than 0.56 V |
CONFIRMATION DRIVING PATTERN
HINT:
- After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here

- When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here

- Connect the Techstream to the DLC3.
- Turn the engine switch on (IG).
- Turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the engine switch off and wait for at least 30 seconds.
- Turn the engine switch on (IG) [A].
- Turn the Techstream on.
- Start the engine.
- With the vehicle stationary, fully depress and release the accelerator pedal [B].
- Idle the engine for 2 seconds or more [C].
- Enter the following menus: Powertrain / Engine / Trouble Codes [D].
- Read the pending DTCs.
HINT:
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
- Enter the following menus: Powertrain / Engine / Utility / All Readiness.
- Input the DTC: P012011.
- Check the DTC judgment result.
Techstream Display
Description
NORMAL
- DTC judgment completed
- System normal
ABNORMAL
- DTC judgment completed
- System abnormal
INCOMPLETE
- DTC judgment not completed
- Perform driving pattern after confirming DTC enabling conditions
HINT:
- If the judgment result is NORMAL, the system is normal.
- If the judgment result is ABNORMAL, the system is malfunctioning.
- If the judgment result is INCOMPLETE, perform steps [B] through [D] again.
- [A] to [D]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- When clearing the permanent DTCs, do not disconnect the cable from the battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.
FAIL-SAFE
When this DTC is stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 7° throttle valve opening angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal angle, to allow the vehicle to continue running at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.
Fail-safe mode continues until a pass condition is detected, and the engine switch is turned off.
WIRING DIAGRAM
HINT:
Read Freeze Frame Data using the Techstream. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
READ VALUE USING TECHSTREAM (THROTTLE POSITION SENSOR NO.1 VOLTAGE)
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine / Data List / Throttle Position Sensor No.1 Voltage.
Powertrain > Engine > Data ListThrottle Position Sensor No.1 Voltage
(e) Read the values displayed on the Techstream.
(f) Disconnect the throttle body with motor assembly connector.
(g) Compare the value of the Data List item Throttle Position Sensor No.1 Voltage after disconnecting the throttle body with motor assembly connector to the value when the connector was connected.
Result | Proceed to |
|---|---|
Changes from less than 0.56 V to higher than 4.535 V |
A |
Does not change from less than 0.56 V |
B |
HINT:
Perform "Inspection After Repair" after replacing the throttle body with motor assembly.
Click here ![]()
| A | REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY |
|
CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)
(a) Disconnect the throttle body with motor assembly connector.
(b) Disconnect the ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
C24-5 (VC) - C56-121 (VCTA) |
Always |
Below 1 Ω |
C24-6 (VTA) or C56-122 (VTA1) - Body ground |
Always |
10 kΩ or higher |
| OK | REPLACE ECM |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
Throttle / Pedal Position Sensor / Switch "A" Circuit Short to Battery or Open (P012015)
DESCRIPTION
Refer to DTC P012011.
Click here ![]()
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
P012015 |
Throttle / Pedal Position Sensor / Switch "A" Circuit Short to Battery or Open |
The output voltage of VTA1 is higher than 4.535 V for 2 seconds or more (1 trip detection logic). |
|
Comes on |
DTC stored |
SAE Code: P0123 |
MONITOR DESCRIPTION
The ECM uses the throttle position sensor to monitor the throttle valve opening angle. If the VTA1 terminal voltage is higher than the threshold, the ECM will illuminate the MIL and store this DTC.
MONITOR STRATEGY
Related DTCs |
P0123: Throttle position sensor 1 range check (high voltage) |
Required Sensors/Components (Main) |
Throttle position sensor |
Required Sensors/Components (Related) |
- |
Frequency of Operation |
Continuous |
Duration |
2 seconds |
MIL Operation |
Immediate |
Sequence of Operation |
None |
TYPICAL ENABLING CONDITIONS
Monitor runs whenever the following DTCs are not stored |
None |
All of the following conditions are met |
- |
Battery voltage |
8 V or higher |
Engine switch |
On (IG) |
Starter |
Off |
TYPICAL MALFUNCTION THRESHOLDS
VTA1 voltage |
Higher than 4.535 V |
CONFIRMATION DRIVING PATTERN
HINT:
- After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here

- When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here

- Connect the Techstream to the DLC3.
- Turn the engine switch on (IG).
- Turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the engine switch off and wait for at least 30 seconds.
- Turn the engine switch on (IG) [A].
- Turn the Techstream on.
- Start the engine.
- With the vehicle stationary, fully depress and release the accelerator pedal [B].
- Idle the engine for 2 seconds or more [C].
- Enter the following menus: Powertrain / Engine / Trouble Codes [D].
- Read the pending DTCs.
HINT:
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
- Enter the following menus: Powertrain / Engine / Utility / All Readiness.
- Input the DTC: P012015.
- Check the DTC judgment result.
Techstream Display
Description
NORMAL
- DTC judgment completed
- System normal
ABNORMAL
- DTC judgment completed
- System abnormal
INCOMPLETE
- DTC judgment not completed
- Perform driving pattern after confirming DTC enabling conditions
HINT:
- If the judgment result is NORMAL, the system is normal.
- If the judgment result is ABNORMAL, the system is malfunctioning.
- If the judgment result is INCOMPLETE, perform steps [B] through [D] again.
- [A] to [D]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- When clearing the permanent DTCs, do not disconnect the cable from the battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.
FAIL-SAFE
When this DTC is stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 7° throttle valve opening angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal angle, to allow the vehicle to continue running at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.
Fail-safe mode continues until a pass condition is detected, and the engine switch is turned off.
WIRING DIAGRAM
Refer to DTC P012011.
Click here ![]()
HINT:
Read Freeze Frame Data using the Techstream. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)
(a) Disconnect the throttle body with motor assembly connector.
(b) Disconnect the ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
C24-6 (VTA) - C56-122 (VTA1) |
Always |
Below 1 Ω |
C24-3 (E2) - C56-120 (ETA) |
Always |
Below 1 Ω |
C24-5 (VC) or C56-121 (VCTA) - Body ground and other terminals |
Always |
10 kΩ or higher |
C24-6 (VTA) or C56-122 (VTA1) - Body ground and other terminals |
Always |
10 kΩ or higher |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
CHECK TERMINAL VOLTAGE (POWER SOURCE OF THROTTLE POSITION SENSOR)
*a |
Front view of wire harness connector (to Throttle Body with Motor Assembly) |
(a) Disconnect the throttle body with motor assembly connector.
(b) Turn the engine switch on (IG).
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
C24-5 (VC) - C24-3 (E2) |
Engine switch on (IG) |
4.5 to 5.5 V |
C24-6 (VTA) - C24-3 (E2) |
Engine switch on (IG) |
3.0 to 5.0 V |
| NG | REPLACE ECM |
|
CHECK HARNESS AND CONNECTOR (RESISTANCE OF ECM)
(a) Disconnect the throttle body with motor assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
C24-5 (VC) - C24-6 (VTA) |
Engine switch off |
190 to 210 kΩ |
| NG | REPLACE ECM |
|
READ VALUE USING TECHSTREAM (THROTTLE POSITION SENSOR NO.1 VOLTAGE)
*a |
Front view of wire harness connector (to Throttle Body with Motor Assembly) |
(a) Disconnect the throttle body with motor assembly connector.
(b) Connect the Techstream to the DLC3.
(c) Turn the engine switch on (IG).
(d) Turn the Techstream on.
(e) Enter the following menus: Powertrain / Engine / Data List / Throttle Position Sensor No.1 Voltage.
Powertrain > Engine > Data ListThrottle Position Sensor No.1 Voltage
(f) According to the display on the Techstream, read the Data List.
HINT:
Use the snapshot function to record the value displayed or make a note of it.
(g) Turn the engine switch off.
(h) Turn the Techstream off.
(i) Connect terminals 3 (E2) and 6 (VTA) of the throttle body with motor assembly connector on the wire harness side.
NOTICE:
If the VTA terminal voltage or the resistance between VTA and E2 is abnormal and terminals 6 (VTA) and 3 (E2) of the throttle body with motor assembly connector are connected, excessive current may flow through the circuit. In this case, do not connect the terminals.
(j) Turn the engine switch on (IG).
(k) Turn the Techstream on.
(l) Enter the following menus: Powertrain / Engine / Data List / Throttle Position Sensor No.1 Voltage.
Powertrain > Engine > Data ListThrottle Position Sensor No.1 Voltage
(m) Compare the vehicle of the Data List item Throttle Position Sensor No.1 Voltage after the circuit is shorted to the value when the throttle body with motor assembly connector was connected.
Result | Proceed to |
|---|---|
Changes from higher than 4.535 V to less than 0.56 V |
A |
Does not change from higher than 4.535 V |
B |
HINT:
Perform "Inspection After Repair" after replacing the throttle body with motor assembly.
Click here ![]()
| A | REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY |
| B | REPLACE ECM |