Definition Of Terms. Diagnosis System. Diagnostic Trouble Code Chart
Definition Of Terms
DEFINITION OF TERMS
Term | Definition |
|---|---|
Monitor Description |
Description of what the ECM monitors and how it detects malfunctions (monitoring purpose and details). |
Related DTCs |
Group of diagnostic trouble codes that are output by the ECM based on the same malfunction detection logic. |
Typical Enabling Conditions |
Preconditions that allow the ECM to detect malfunctions. With all preconditions satisfied, the ECM stores a DTC when the monitored value(s) exceeds the malfunction threshold(s). |
Sequence of Operation |
The priority order that is applied to monitoring if multiple sensors and components are used to detect the malfunction. While one sensor is being monitored, the next sensor or component will not be monitored. |
Required Sensors/Components |
The sensors and components that are used by the ECM to detect malfunctions. |
Frequency of Operation |
The number of times that the ECM checks for malfunctions per driving cycle. "Once per driving cycle" means that the ECM detects a malfunction only once during a single driving cycle. "Continuous" means that the ECM detects a malfunction every time the enabling conditions are met. |
Duration |
The minimum time for which the ECM must detect a continuous deviation in the monitored value(s) in order to store a DTC. Timing begins after the "typical enabling conditions" are met. |
Typical Malfunction Thresholds |
Value beyond which the ECM will determine that there is a malfunction and stores a DTC. |
MIL Operation |
MIL illumination timing after a malfunction is detected. "Immediate" means that the ECM illuminates the MIL the instant the ECM determines that there is a malfunction. "2 driving cycles" means that the ECM illuminates the MIL if the same malfunction is detected again in the next driving cycle. |
Component Operating Range |
Normal operation range of sensors and solenoids under normal driving conditions. Use these ranges as a reference. They cannot be used to judge if a sensor or solenoid is defective or not. |
Diagnosis System
DIAGNOSIS SYSTEM
DESCRIPTION
When troubleshooting OBD II (On-Board Diagnostics) vehicles, the Techstream (complying with SAE J1978) must be connected to the DLC3 (Data Link Connector 3) of the vehicle. Various data in the vehicle's ECM (Engine Control Module) can be then read.
OBD II regulations require that the vehicle's on-board computer illuminates the MIL (Malfunction Indicator Lamp) on the instrument panel when the computer detects a malfunction in:
- The emission control system and components.
- The powertrain control components (which affect vehicle emissions).
- The computer itself.
In addition, the applicable DTCs prescribed by SAE J2012 are stored in the ECM memory. If the malfunction does not recur in 3 consecutive trips, the MIL turns off automatically but the DTCs remain stored in the ECM memory.
To check the DTCs, connect the Techstream to the DLC3. The Techstream displays output DTCs, freeze frame data, and a variety of engine data. The DTCs and freeze frame data can be cleared with the Techstream. In order to enhance OBD function on vehicles and develop the Off-Board diagnosis system, Controller Area Network (CAN) communication is used in this system. CAN is a network which uses a pair of data transmission lines spanning multiple computers and sensors. It allows for high speed communications between the systems and simplification of the wire harness connections.
NORMAL MODE AND CHECK MODE
The diagnosis system operates in normal mode during normal vehicle use. In normal mode, 2 trip detection logic is used to ensure accurate detection of malfunctions. Check mode is also available as an option for technicians. In check mode, 1 trip detection logic is used for duplicating malfunction symptoms and increasing the system's ability to detect malfunctions, including intermittent problems (Techstream only).
2 TRIP DETECTION LOGIC
When a malfunction is first detected, the malfunction is temporarily stored in the ECM memory (1st trip). If the same malfunction is detected during the subsequent drive cycle, the MIL is illuminated (2nd trip).
DLC3 (Data Link Connector 3)
(a) Check the DLC3.
Click here ![]()
FREEZE FRAME DATA
The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data stored at the time of a malfunction.
BATTERY VOLTAGE
Standard Voltage:
11 to 14 V
If the voltage is less than 11 V, recharge or replace the battery.
MIL (Malfunction Indicator Lamp)
(a) The MIL is illuminated when the engine switch is turned on (IG) (with the engine is not running).
(b) The MIL turns off when the engine is started. If the MIL remains illuminated, the diagnosis system has detected a malfunction or abnormality in the system.
HINT:
If the MIL is not illuminated when the engine switch is turned on (IG), check the MIL circuit.
Click here ![]()
ALL READINESS
HINT:
- With "All Readiness", you can check whether or not the DTC judgment has been completed by using the Techstream.
- You should check "All Readiness" after simulating malfunction symptoms or for validation after finishing repairs.
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Clear the DTCs.
Powertrain > Engine > Clear DTCs(e) Turn the engine switch off and wait for at least 30 seconds.
(f) Turn the engine switch on (IG) and turn the Techstream on.
(g) Perform the DTC judgment driving pattern to run the DTC judgment.
(h) Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Powertrain > Engine > UtilityAll Readiness
(i) Input the DTCs to be confirmed.
(j) Check the DTC judgment result.
Techstream Display | Description |
|---|---|
NORMAL |
|
ABNORMAL |
|
INCOMPLETE |
|
DIAGNOSIS RELATED INFORMATION
HINT:
- If the detection conditions of certain DTCs are met before a malfunction can be confirmed, the ECM will store Diagnosis Related Information. Vehicle condition information from when the detection conditions were met can be checked using the Diagnosis Related Information. Diagnosis Related Information should be used as a reference only, and should not be relied upon solely when determining whether a part is faulty or not.
- Clearing DTCs will also clear Diagnosis Related Information.
- DTCs and Diagnosis Related Information are saved in the Techstream at the same time.
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine / Utility / Diagnosis Related Information.
Powertrain > Engine > UtilityDiagnosis Related Information
(e) Select a Diagnosis Related Information item to display it' s details.
Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART
SFI SystemDTC No. | Detection Item | MIL | Memory | Note | Link |
|---|---|---|---|---|---|
P001013 |
A Camshaft Position Actuator Bank 1 Circuit Open |
Comes on |
DTC stored |
SAE Code: P0010 |
|
P001100 |
Camshaft Position "A" - Timing Over-Advanced or System Performance Bank 1 |
Comes on |
DTC stored |
SAE Code: P0011 |
|
P001107 |
Camshaft Position "A" - Timing Over-Advanced or System Performance Bank 1 Mechanical Failure |
Comes on |
DTC stored |
SAE Code: P0011 |
|
P001200 |
Camshaft Position "A" - Timing Over-Retarded Bank 1 |
Comes on |
DTC stored |
SAE Code: P0012 |
|
P001313 |
Camshaft Position "B" - Actuator Bank 1 Circuit Open |
Comes on |
DTC stored |
SAE Code: P0013 |
|
P001400 |
Camshaft Position "B" - Timing Over-Advanced or System Performance Bank 1 |
Comes on |
DTC stored |
SAE Code: P0014 |
|
P001500 |
Camshaft Position "B" - Timing Over-Retarded Bank 1 |
Comes on |
DTC stored |
SAE Code: P0015 |
|
P001600 |
Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor A |
Comes on |
DTC stored |
SAE Code: P0016 |
|
P001700 |
Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor B |
Comes on |
DTC stored |
SAE Code: P0017 |
|
P001800 |
Crankshaft Position - Camshaft Position Correlation Bank 2 Sensor A |
Comes on |
DTC stored |
SAE Code: P0018 |
|
P001900 |
Crankshaft Position - Camshaft Position Correlation Bank 2 Sensor B |
Comes on |
DTC stored |
SAE Code: P0019 |
|
P002013 |
Camshaft Position "A" Actuator Bank 2 Circuit Open |
Comes on |
DTC stored |
SAE Code: P0020 |
|
P002100 |
Camshaft Position "A" - Timing Over-Advanced or System Performance Bank 2 |
Comes on |
DTC stored |
SAE Code: P0021 |
|
P002107 |
Camshaft Position "A" - Timing Over-Advanced or System Performance Bank 2 Mechanical Failure |
Comes on |
DTC stored |
SAE Code: P0021 |
|
P002200 |
Camshaft Position "A" - Timing Over-Retarded Bank 2 |
Comes on |
DTC stored |
SAE Code: P0022 |
|
P002313 |
Camshaft Position "B" - Actuator Bank 2 Circuit Open |
Comes on |
DTC stored |
SAE Code: P0023 |
|
P002400 |
Camshaft Position "B" - Timing Over-Advanced or System Performance Bank 2 |
Comes on |
DTC stored |
SAE Code: P0024 |
|
P002500 |
Camshaft Position "B" - Timing Over-Retarded Bank 2 |
Comes on |
DTC stored |
SAE Code: P0025 |
|
P003012 |
HO2S Heater Control Bank 1 Sensor 1 Circuit Short to Battery |
Comes on |
DTC stored |
SAE Code: P0032 |
|
P003013 |
HO2S Heater Control Bank 1 Sensor 1 Circuit Open |
Comes on |
DTC stored |
SAE Code: P0031 |
|
P003612 |
HO2S Heater Control Circuit Bank 1 Sensor 2 Circuit Short to Battery |
Comes on |
DTC stored |
SAE Code: P0038 |
|
P003614 |
HO2S Heater Control Circuit Bank 1 Sensor 2 Circuit Short to Ground or Open |
Comes on |
DTC stored |
SAE Code: P0037 |
|
P005012 |
HO2S Heater Control Bank 2 Sensor 1 Circuit Short to Battery |
Comes on |
DTC stored |
SAE Code: P0052 |
|
P005013 |
HO2S Heater Control Bank 2 Sensor 1 Circuit Open |
Comes on |
DTC stored |
SAE Code: P0051 |
|
P005612 |
HO2S Heater Control Bank 2 Sensor 2 Circuit Short to Battery |
Comes on |
DTC stored |
SAE Code: P0058 |
|
P005614 |
HO2S Heater Control Bank 2 Sensor 2 Circuit Short to Ground or Open |
Comes on |
DTC stored |
SAE Code: P0057 |
|
P008700 |
Fuel Rail / System Pressure - Too Low |
Comes on |
DTC stored |
SAE Code: P0087 |
|
P008800 |
Fuel Rail / System Pressure - Too High |
Comes on |
DTC stored |
SAE Code: P0088 |
|
P008A00 |
Low Pressure Fuel System Pressure - Too Low |
Does not come on |
DTC stored |
SAE Code: P008A |
|
P008B00 |
Low Pressure Fuel System Pressure - Too High |
Does not come on |
DTC stored |
SAE Code: P008B |
|
P00FE00 |
EVAP System Tank Vapor Line Restricted/Blocked |
Comes on |
DTC stored |
SAE Code: P00FE |
|
P010012 |
Mass or Volume Air Flow Sensor "A" Circuit Short to Battery |
Comes on |
DTC stored |
SAE Code: P0103 |
|
P010014 |
Mass or Volume Air Flow Sensor "A" Circuit Short to Ground or Open |
Comes on |
DTC stored |
SAE Code: P0102 |
|
P010064 |
Mass or Volume Air Flow Sensor "A" Signal Plausibility Failure |
Comes on |
DTC stored |
SAE Code: P0101 |
|
P011011 |
Intake Air Temperature Sensor 1 Bank 1 Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P0112 |
|
P011015 |
Intake Air Temperature Sensor 1 Bank 1 Circuit Short to Battery or Open |
Comes on |
DTC stored |
SAE Code: P0113 |
|
P01102A |
Intake Air Temperature Sensor 1 Bank 1 Signal Stuck in Range |
Comes on |
DTC stored |
SAE Code: P0111 |
|
P011511 |
Engine Coolant Temperature Sensor 1 Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P0117 |
|
P011515 |
Engine Coolant Temperature Sensor 1 Circuit Short to Battery or Open |
Comes on |
DTC stored |
SAE Code: P0118 |
|
P01152A |
Engine Coolant Temperature Sensor 1 Signal Stuck in Range |
Comes on |
DTC stored |
SAE Code: P0116 |
|
P011B62 |
Engine Coolant Temperature / Intake Air Temperature Signal Compare Failure |
Comes on |
DTC stored |
SAE Code: P011B |
|
P012011 |
Throttle / Pedal Position Sensor / Switch "A" Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P0122 |
|
P012015 |
Throttle / Pedal Position Sensor / Switch "A" Circuit Short to Battery or Open |
Comes on |
DTC stored |
SAE Code: P0123 |
|
P01201C |
Throttle / Pedal Position Sensor / Switch "A" Circuit Voltage Out of Range |
Comes on |
DTC stored |
SAE Code: P0121 |
|
P012500 |
Insufficient Coolant Temperature for Closed Loop Fuel Control |
Comes on |
DTC stored |
SAE Code: P0125 |
|
P012800 |
Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature) |
Comes on |
DTC stored |
SAE Code: P0128 |
|
P012807 |
Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature) Mechanical Failure |
Comes on |
DTC stored |
SAE Code: P0128 |
|
P013611 |
O2 Sensor Circuit Bank 1 Sensor 2 Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P0136 |
|
P013613 |
O2 Sensor Circuit Bank 1 Sensor 2 Circuit Open |
Comes on |
DTC stored |
SAE Code: P0136 |
|
P013614 |
O2 Sensor Circuit Bank 1 Sensor 2 Circuit Short to Ground or Open |
Comes on |
DTC stored |
SAE Code: P0137 |
|
P013615 |
O2 Sensor Circuit Bank 1 Sensor 2 Circuit Short to Battery or Open |
Comes on |
DTC stored |
SAE Code: P0138 |
|
P013617 |
O2 Sensor Circuit Bank 1 Sensor 2 Circuit Voltage Above Threshold |
Comes on |
DTC stored |
SAE Code: P0137 |
|
P013623 |
O2 Sensor Circuit Bank 1 Sensor 2 Signal Stuck Low |
Comes on |
DTC stored |
SAE Code: P0139 |
|
P013A00 |
O2 Sensor Slow Response - Rich to Lean Bank 1 Sensor 2 |
Comes on |
DTC stored |
SAE Code: P013A |
|
P013C00 |
O2 Sensor Slow Response - Rich to Lean Bank 2 Sensor 2 |
Comes on |
DTC stored |
SAE Code: P013C |
|
P014118 |
O2 Sensor Heater Circuit Bank 1 Sensor 2 Circuit Current Below Threshold |
Comes on |
DTC stored |
SAE Code: P0141 |
|
P014C00 |
O2 Sensor Slow Response - Rich to Lean Bank 1 Sensor 1 |
Comes on |
DTC stored |
SAE Code: P014C |
|
P014D00 |
O2 Sensor Slow Response - Lean to Rich Bank 1 Sensor 1 |
Comes on |
DTC stored |
SAE Code: P014D |
|
P014E00 |
O2 Sensor Slow Response - Rich to Lean Bank 2 Sensor 1 |
Comes on |
DTC stored |
SAE Code: P014E |
|
P014F00 |
O2 Sensor Slow Response - Lean to Rich Bank 2 Sensor 1 |
Comes on |
DTC stored |
SAE Code: P014F |
|
P015611 |
O2 Sensor Circuit Bank 2 Sensor 2 Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P0156 |
|
P015613 |
O2 Sensor Circuit Bank 2 Sensor 2 Circuit Open |
Comes on |
DTC stored |
SAE Code: P0156 |
|
P015614 |
O2 Sensor Circuit Bank 2 Sensor 2 Circuit Short to Ground or Open |
Comes on |
DTC stored |
SAE Code: P0157 |
|
P015615 |
O2 Sensor Circuit Bank 2 Sensor 2 Circuit Short to Battery or Open |
Comes on |
DTC stored |
SAE Code: P0158 |
|
P015617 |
O2 Sensor Circuit Bank 2 Sensor 2 Circuit Voltage Above Threshold |
Comes on |
DTC stored |
SAE Code: P0157 |
|
P015623 |
O2 Sensor Circuit Bank 2 Sensor 2 Signal Stuck Low |
Comes on |
DTC stored |
SAE Code: P0159 |
|
P015A00 |
O2 Sensor Delayed Response - Rich to Lean Bank 1 Sensor 1 |
Comes on |
DTC stored |
SAE Code: P015A |
|
P015B00 |
O2 Sensor Delayed Response - Lean to Rich Bank 1 Sensor 1 |
Comes on |
DTC stored |
SAE Code: P015B |
|
P015C00 |
O2 Sensor Delayed Response - Rich to Lean Bank 2 Sensor 1 |
Comes on |
DTC stored |
SAE Code: P015C |
|
P015D00 |
O2 Sensor Delayed Response - Lean to Rich Bank 2 Sensor 1 |
Comes on |
DTC stored |
SAE Code: P015D |
|
P016118 |
O2 Sensor Heater Circuit Bank 2 Sensor 2 Circuit Current Below |
Comes on |
DTC stored |
SAE Code: P0161 |
|
P017100 |
System Too Lean Bank 1 |
Comes on |
DTC stored |
SAE Code: P0171 |
|
P017200 |
System Too Rich Bank 1 |
Comes on |
DTC stored |
SAE Code: P0172 |
|
P017400 |
System Too Lean Bank 2 |
Comes on |
DTC stored |
SAE Code: P0174 |
|
P017500 |
System Too Rich Bank 2 |
Comes on |
DTC stored |
SAE Code: P0175 |
|
P019011 |
Fuel Rail Pressure Sensor "A" Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P0192 |
|
P019015 |
Fuel Rail Pressure Sensor "A" Circuit Short to Battery or Open |
Comes on |
DTC stored |
SAE Code: P0193 |
|
P01902A |
Fuel Rail Pressure Sensor "A" Signal Stuck in Range |
Comes on |
DTC stored |
SAE Code: P0191 |
|
P019064 |
Fuel Rail Pressure Sensor "A" Signal Plausibility Failure |
Comes on |
DTC stored |
SAE Code: P0191 |
|
P020113 |
Cylinder 1 Injector "A" Circuit Open |
Comes on |
DTC stored |
SAE Code: P0201 |
|
P020213 |
Cylinder 2 Injector "A" Circuit Open |
Comes on |
DTC stored |
SAE Code: P0202 |
|
P020313 |
Cylinder 3 Injector "A" Circuit Open |
Comes on |
DTC stored |
SAE Code: P0203 |
|
P020413 |
Cylinder 4 Injector "A" Circuit Open |
Comes on |
DTC stored |
SAE Code: P0204 |
|
P020513 |
Cylinder 5 Injector "A" Circuit Open |
Comes on |
DTC stored |
SAE Code: P0205 |
|
P020613 |
Cylinder 6 Injector "A" Circuit Open |
Comes on |
DTC stored |
SAE Code: P0206 |
|
P022011 |
Throttle/Pedal Position Sensor/Switch "B" Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P0222 |
|
P022015 |
Throttle/Pedal Position Sensor/Switch "B" Circuit Short to Battery or Open |
Comes on |
DTC stored |
SAE Code: P0223 |
|
P030000 |
Random/Multiple Cylinder Misfire Detected |
Comes on/Blinks* *: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored |
SAE Code: P0300 |
|
P030027 |
Random/Multiple Cylinder Misfire Detected (Emission) Signal Rate of Change Above Threshold |
Comes on |
DTC stored |
SAE Code: - |
|
P030085 |
Random / Multiple Cylinder Misfire Detected (Over Temperature) Signal Above Allowable Range |
Comes on/Blinks* *: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored |
SAE Code: - |
|
P030100 |
Cylinder 1 Misfire Detected |
Comes on/Blinks* *: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored |
SAE Code: P0301 |
|
P030200 |
Cylinder 2 Misfire Detected |
Comes on/Blinks* *: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored |
SAE Code: P0302 |
|
P030300 |
Cylinder 3 Misfire Detected |
Comes on/Blinks* *: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored |
SAE Code: P0303 |
|
P030400 |
Cylinder 4 Misfire Detected |
Comes on/Blinks* *: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored |
SAE Code: P0304 |
|
P030500 |
Cylinder 5 Misfire Detected |
Comes on/Blinks* *: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored |
SAE Code: P0305 |
|
P030600 |
Cylinder 6 Misfire Detected |
Comes on/Blinks* *: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored |
SAE Code: P0306 |
|
P032511 |
Knock Sensor 1 Bank 1 or Single Sensor Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P0327 |
|
P032515 |
Knock Sensor 1 Bank 1 or Single Sensor Circuit Short to Battery or Open |
Comes on |
DTC stored |
SAE Code: P0328 |
|
P033011 |
Knock Sensor 2 Bank 2 Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P0332 |
|
P033015 |
Knock Sensor 2 Bank 2 Circuit Short to Battery or Open |
Comes on |
DTC stored |
SAE Code: P0333 |
|
P033511 |
Crankshaft Position Sensor "A" Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P0337 |
|
P033515 |
Crankshaft Position Sensor "A" Circuit Short to Battery or Open |
Comes on |
DTC stored |
SAE Code: P0338 |
|
P03351F |
Crankshaft Position Sensor "A" Circuit Intermittent |
Does not come on |
DTC stored |
SAE Code: P0339 |
|
P03352A |
Crankshaft Position Sensor "A" Signal Stuck in Range |
Comes on |
DTC stored |
SAE Code: P0335 |
|
P033531 |
Crankshaft Position Sensor "A" No Signal |
Comes on |
DTC stored |
SAE Code: P0335 |
|
P034011 |
Camshaft Position Sensor "A" Bank 1 or Single Sensor Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P0342 |
|
P034015 |
Camshaft Position Sensor "A" Bank 1 or Single Sensor Circuit Short to Battery or Open |
Comes on |
DTC stored |
SAE Code: P0343 |
|
P034031 |
Camshaft Position Sensor "A" Bank 1 or Single Sensor No Signal |
Comes on |
DTC stored |
SAE Code: P0340 |
|
P034511 |
Camshaft Position Sensor "A" Bank 2 Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P0347 |
|
P034515 |
Camshaft Position Sensor "A" Bank 2 Circuit Short to Battery or Open |
Comes on |
DTC stored |
SAE Code: P0348 |
|
P034531 |
Camshaft Position Sensor "A" Bank 2 No Signal |
Comes on |
DTC stored |
SAE Code: P0345 |
|
P035113 |
Ignition Coil "A" Circuit Open |
Comes on |
DTC stored |
SAE Code: P0351 |
|
P035213 |
Ignition Coil "B" Circuit Open |
Comes on |
DTC stored |
SAE Code: P0352 |
|
P035313 |
Ignition Coil "C" Circuit Open |
Comes on |
DTC stored |
SAE Code: P0353 |
|
P035413 |
Ignition Coil "D" Circuit Open |
Comes on |
DTC stored |
SAE Code: P0354 |
|
P035513 |
Ignition Coil "E" Circuit Open |
Comes on |
DTC stored |
SAE Code: P0355 |
|
P035613 |
Ignition Coil "F" Circuit Open |
Comes on |
DTC stored |
SAE Code: P0356 |
|
P036511 |
Camshaft Position Sensor "B" Bank 1 Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P0367 |
|
P036515 |
Camshaft Position Sensor "B" Bank 1 Circuit Short to Battery or Open |
Comes on |
DTC stored |
SAE Code: P0368 |
|
P03652A |
Camshaft Position Sensor "B" Bank 1 Signal Stuck in Range |
Comes on |
DTC stored |
SAE Code: P0365 |
|
P036531 |
Camshaft Position Sensor "B" Bank 1 No Signal |
Comes on |
DTC stored |
SAE Code: P0365 |
|
P039011 |
Camshaft Position Sensor "B" Bank 2 Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P0392 |
|
P039015 |
Camshaft Position Sensor "B" Bank 2 Circuit Short to Battery or Open |
Comes on |
DTC stored |
SAE Code: P0393 |
|
P039031 |
Camshaft Position Sensor "B" Bank 2 No Signal |
Comes on |
DTC stored |
SAE Code: P0390 |
|
P042000 |
Catalyst System Efficiency Below Threshold Bank 1 |
Comes on |
DTC stored |
SAE Code: P0420 |
|
P043000 |
Catalyst System Efficiency Below Threshold Bank 2 |
Comes on |
DTC stored |
SAE Code: P0430 |
|
P043E00 |
Evaporative Emission System Leak Detection Reference Orifice Low Flow |
Comes on |
DTC stored |
SAE Code: P043E |
|
P043F00 |
Evaporative Emission System Leak Detection Reference Orifice High Flow |
Comes on |
DTC stored |
SAE Code: P043F |
|
P04417E |
Evaporative Emission System Incorrect Purge Flow Actuator Stuck On |
Comes on |
DTC stored |
SAE Code: P0441 |
|
P04417F |
Evaporative Emission System Incorrect Purge Flow Actuator Stuck Off |
Comes on |
DTC stored |
SAE Code: P0441 |
|
P04419C |
Evaporative Emission System Incorrect Purge Flow Low/Insufficient Flow |
Comes on |
DTC stored |
SAE Code: P0441 |
|
P045011 |
Evaporative Emission System Pressure Sensor/Switch Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P0452 |
|
P045015 |
Evaporative Emission System Pressure Sensor/Switch Circuit Short to Battery or Open |
Comes on |
DTC stored |
SAE Code: P0453 |
|
P04502A |
Evaporative Emission System Pressure Sensor/Switch Signal Stuck in Range |
Comes on |
DTC stored |
SAE Code: P0451 |
|
P04502F |
Evaporative Emission System Pressure Sensor/Switch Signal Erratic |
Comes on |
DTC stored |
SAE Code: P0451 |
|
P045500 |
Evaporative Emission System Leak Detected (Large Leak) |
Comes on |
DTC stored |
SAE Code: P0455 |
|
P045600 |
Evaporative Emission System Leak Detected (Very Small Leak) |
Comes on |
DTC stored |
SAE Code: P0456 |
|
P046012 |
Fuel Level Sensor "A" Circuit Short to Battery |
Comes on |
DTC stored |
SAE Code: P0463 |
|
P046014 |
Fuel Level Sensor "A" Circuit Short to Ground or Open |
Comes on |
DTC stored |
SAE Code: P0462 |
|
P04602A |
Fuel Level Sensor "A" Signal Stuck In Range |
Comes on |
DTC stored |
SAE Code: P0461 |
|
P050031 |
Vehicle Speed Sensor "A" No Signal |
Comes on |
DTC stored |
SAE Code: P0500 |
|
P05042B |
Brake Switch "A"/"B" Signal Cross Coupled |
Does not come on |
DTC stored |
SAE Code: P0504 |
|
P050500 |
Idle Control System |
Comes on |
DTC stored |
SAE Code: P0505 |
|
P050A00 |
Cold Start Idle Control System Performance |
Comes on |
DTC stored |
SAE Code: P050A |
|
P050B00 |
Cold Start Ignition Timing Performance |
Comes on |
DTC stored |
SAE Code: P050B |
|
P056014 |
System Voltage Circuit Short to Ground or Open |
Comes on |
DTC stored |
SAE Code: P0562 |
|
P059712 |
Thermostat Heater Control Circuit Short to Battery |
Comes on |
DTC stored |
SAE Code: P0599 |
|
P059714 |
Thermostat Heater Control Circuit Short to Ground or Open |
Comes on |
DTC stored |
SAE Code: P0598 |
|
P060444 |
Internal Control Module Random Access Memory (RAM) Error Data Memory Failure |
Comes on |
DTC stored |
SAE Code: P0604 |
|
P060596 |
Control Module Performance Bank 2 Component Internal Failure |
Comes on |
DTC stored |
SAE Code: P0607 |
|
P060604 |
Control Module Processor System Internal Failure |
Comes on |
DTC stored |
SAE Code: P0606 |
|
P060629 |
Control Module Processor Signal Invalid |
Comes on |
DTC stored |
SAE Code: P0606 |
|
P06062A |
Control Module Processor Signal Stuck in Range |
Comes on |
DTC stored |
SAE Code: P0606 |
|
P060647 |
Control Module Processor Watchdog/Safety MCU Failure |
Comes on |
DTC stored |
SAE Code: P0606 |
|
P060796 |
Control Module Performance Bank 1 Component Internal Failure |
Comes on |
DTC stored |
SAE Code: P0607 |
|
P060A47 |
Internal Control Module Monitoring Processor Performance Watchdog/Safety MCU Failure |
Comes on |
DTC stored |
SAE Code: P060A |
|
P060B49 |
Internal Control Module A/D Processing Performance Internal Electronic Failure |
Comes on |
DTC stored |
SAE Code: P060B |
|
P060D49 |
Internal Control Module Accelerator Pedal Position Performance Internal Electronic Failure |
Comes on |
DTC stored |
SAE Code: P060D |
|
P060E49 |
Internal Control Module Throttle Position Performance Internal Electronic Failure |
Comes on |
DTC stored |
SAE Code: P060E |
|
P061512 |
Starter Relay Circuit Short to Battery |
Comes on |
DTC stored |
SAE Code: P0617 |
|
P061E49 |
Internal Control Module Brake Signal Internal Electronic Failure |
Comes on |
DTC stored |
SAE Code: P061E |
|
P062D13 |
Fuel Injector Driver Circuit Performance Bank 1 Circuit Open |
Comes on |
DTC stored |
SAE Code: P062D |
|
P062F44 |
Internal Control Module EEPROM Data Memory Failure |
Comes on |
DTC stored |
SAE Code: P062F |
|
P063051 |
VIN Not Programmed |
Comes on |
DTC stored |
SAE Code: P0630 |
|
P065714 |
Actuator Supply Voltage "A" Circuit Short to Ground or Open |
Comes on |
DTC stored |
SAE Code: P0658 |
|
P06579E |
Actuator Supply Voltage "A" Stuck On |
Comes on |
DTC stored |
SAE Code: P0657 |
|
P070312 |
Brake Switch "B" Circuit Short to Battery |
Does not come on |
DTC stored |
SAE Code: P0724 |
|
P070513 |
Transmission Range Sensor "A" Circuit Open |
Comes on |
DTC stored |
SAE Code: P0705 |
|
P070562 |
Transmission Range Sensor "A" Signal Compare Failure |
Comes on |
DTC stored |
SAE Code: P0705 |
|
P101A9E |
A/F Sensor Heater Performance Bank 1 Sensor 1 Stuck On |
Comes on |
DTC stored |
SAE Code: P101D |
|
P102A9E |
O2 Sensor Heater Performance Bank 1 Sensor 2 Stuck On |
Comes on |
DTC stored |
SAE Code: P102D |
|
P103A9E |
A/F Sensor Heater Performance Bank 2 Sensor 1 Stuck On |
Comes on |
DTC stored |
SAE Code: P103D |
|
P105A9E |
O2 Sensor Heater Performance Bank 2 Sensor 2 Stuck On |
Comes on |
DTC stored |
SAE Code: P105D |
|
P107A11 |
Fuel Rail Pressure Sensor (Low) Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P107C |
|
P107A15 |
Fuel Rail Pressure Sensor (Low) Circuit Short to Battery or Open |
Comes on |
DTC stored |
SAE Code: P107D |
|
P107A2A |
Fuel Rail Pressure Sensor (Low) Signal Stuck in Range |
Comes on |
DTC stored |
SAE Code: P107B |
|
P107A64 |
Fuel Rail Pressure Sensor (Low) Signal Plausibility Failure |
Comes on |
DTC stored |
SAE Code: P107B |
|
P117000 |
Fuel Performance/Port Injector |
Does not come on |
DTC stored |
SAE Code: P1170 |
|
P117B00 |
Fuel Performance/Direct Injector |
Does not come on |
DTC stored |
SAE Code: P117B |
|
P11EA00 |
Bank 1 Air-Fuel Ratio Imbalance (Port) |
Comes on |
DTC stored |
SAE Code: P11EA |
|
P11EB00 |
Bank 2 Air-Fuel Ratio Imbalance (Port) |
Comes on |
DTC stored |
SAE Code: P11EB |
|
P11EC00 |
Cylinder #1 Air-Fuel Ratio Imbalance (Port) |
Comes on |
DTC stored |
SAE Code: P11EC |
|
P11ED00 |
Cylinder #2 Air-Fuel Ratio Imbalance (Port) |
Comes on |
DTC stored |
SAE Code: P11ED |
|
P11EE00 |
Cylinder #3 Air-Fuel Ratio Imbalance (Port) |
Comes on |
DTC stored |
SAE Code: P11EE |
|
P11EF00 |
Cylinder #4 Air-Fuel Ratio Imbalance (Port) |
Comes on |
DTC stored |
SAE Code: P11EF |
|
P11F000 |
Cylinder #5 Air-Fuel Ratio Imbalance (Port) |
Comes on |
DTC stored |
SAE Code: P11F0 |
|
P11F100 |
Cylinder #6 Air-Fuel Ratio Imbalance (Port) |
Comes on |
DTC stored |
SAE Code: P11F1 |
|
P123513 |
High Pressure Fuel Pump Circuit Open |
Comes on |
DTC stored |
SAE Code: P1235 |
|
P160300 |
Engine Stall History |
Does not come on |
DTC stored |
SAE Code: P1603 |
|
P160400 |
Startability Malfunction |
Does not come on |
DTC stored |
SAE Code: P1604 |
|
P160500 |
Rough Idling |
Does not come on |
DTC stored |
SAE Code: P1605 |
|
P160700 |
Cruise Control Input Processor |
Comes on |
DTC stored |
SAE Code: P1607 |
|
P210014 |
Throttle Actuator "A" Control Motor Circuit Short to Ground or Open |
Comes on |
DTC stored |
SAE Code: P2102 |
|
P210015 |
Throttle Actuator "A" Control Motor Circuit Short to Battery or Open |
Comes on |
DTC stored |
SAE Code: P2103 |
|
P210900 |
Throttle/Pedal Position Sensor "A" Minimum Stop Performance |
Does not come on |
DTC stored |
SAE Code: P2109 |
|
P211172 |
Throttle Actuator "A" Control System Actuator Stuck Open |
Comes on |
DTC stored |
SAE Code: P2111 |
|
P211173 |
Throttle Actuator "A" Control System Actuator Stuck Closed |
Comes on |
DTC stored |
SAE Code: P2112 |
|
P211900 |
Throttle Actuator "A" Control Throttle Body Range/Performance |
Comes on |
DTC stored |
SAE Code: P2119 |
|
P211904 |
Throttle Actuator "A" Control Throttle Body Range/Performance System Internal Failure |
Comes on |
DTC stored |
SAE Code: P2119 |
|
P211977 |
Throttle Actuator "A" Control Throttle Body Range/Performance Commanded Position Not Reachable |
Comes on |
DTC stored |
SAE Code: P2119 |
|
P212012 |
Throttle/Pedal Position Sensor/Switch "D" Circuit Short to Battery |
Comes on |
DTC stored |
SAE Code: P2123 |
|
P212014 |
Throttle/Pedal Position Sensor/Switch "D" Circuit Short to Ground or Open |
Comes on |
DTC stored |
SAE Code: P2122 |
|
P21201C |
Throttle/Pedal Position Sensor/Switch "D" Voltage Out of Range |
Comes on |
DTC stored |
SAE Code: P2121 |
|
P21201F |
Throttle/Pedal Position Sensor/Switch "D" Circuit Intermittent |
Comes on |
DTC stored |
SAE Code: P2120 |
|
P212099 |
Throttle/Pedal Position Sensor/Switch "D" Exceeded Learning Limit |
Comes on |
DTC stored |
SAE Code: P2121 |
|
P212512 |
Throttle/Pedal Position Sensor/Switch "E" Circuit Short to Battery |
Comes on |
DTC stored |
SAE Code: P2128 |
|
P212514 |
Throttle/Pedal Position Sensor/Switch "E" Circuit Short to Ground or Open |
Comes on |
DTC stored |
SAE Code: P2127 |
|
P21251F |
Throttle/Pedal Position Sensor/Switch "E" Circuit Intermittent |
Comes on |
DTC stored |
SAE Code: P2125 |
|
P21352B |
Throttle/Pedal Position Sensor/Switch "A"/"B" Voltage Correlation Signal Cross Coupled |
Comes on |
DTC stored |
SAE Code: P2135 |
|
P21382B |
Throttle/Pedal Position Sensor/Switch "D"/"E" Voltage Correlation Signal Cross Coupled |
Comes on |
DTC stored |
SAE Code: P2138 |
|
P219519 |
A/F (O2) Sensor Signal Biased/Stuck Lean Bank 1 Sensor 1 Circuit Current Above Threshold |
Comes on |
DTC stored |
SAE Code: P2195 |
|
P219524 |
A/F (O2) Sensor Signal Biased/Stuck Lean Bank 1 Sensor 1 Signal Stuck High |
Comes on |
DTC stored |
SAE Code: P2195 |
|
P219618 |
A/F (O2) Sensor Signal Biased/Stuck Rich Bank 1 Sensor 1 Circuit Current Below Threshold |
Comes on |
DTC stored |
SAE Code: P2196 |
|
P219623 |
A/F (O2) Sensor Signal Biased/Stuck Rich Bank 1 Sensor 1 Signal Stuck Low |
Comes on |
DTC stored |
SAE Code: P2196 |
|
P219719 |
A/F (O2) Sensor Signal Biased/Stuck Lean Bank 2 Sensor 1 Circuit Current Above Threshold |
Comes on |
DTC stored |
SAE Code: P2197 |
|
P219724 |
A/F (O2) Sensor Signal Biased/Stuck Lean Bank 2 Sensor 1 Signal Stuck High |
Comes on |
DTC stored |
SAE Code: P2197 |
|
P219818 |
A/F (O2) Sensor Signal Biased/Stuck Rich Bank 2 Sensor 1 Circuit Current Below Threshold |
Comes on |
DTC stored |
SAE Code: P2198 |
|
P219823 |
A/F (O2) Sensor Signal Biased/Stuck Rich Bank 2 Sensor 1 Signal Stuck Low |
Comes on |
DTC stored |
SAE Code: P2198 |
|
P219A00 |
Bank 1 Air-Fuel Ratio Imbalance |
Comes on |
DTC stored |
SAE Code: P219A |
|
P219B00 |
Bank 2 Air-Fuel Ratio Imbalance |
Comes on |
DTC stored |
SAE Code: P219B |
|
P219C00 |
Cylinder 1 Air-Fuel Ratio Imbalance |
Comes on |
DTC stored |
SAE Code: P219C |
|
P219D00 |
Cylinder 2 Air-Fuel Ratio Imbalance |
Comes on |
DTC stored |
SAE Code: P219D |
|
P219E00 |
Cylinder 3 Air-Fuel Ratio Imbalance |
Comes on |
DTC stored |
SAE Code: P219E |
|
P219F00 |
Cylinder 4 Air-Fuel Ratio Imbalance |
Comes on |
DTC stored |
SAE Code: P219F |
|
P21A000 |
Cylinder 5 Air-Fuel Ratio Imbalance |
Comes on |
DTC stored |
SAE Code: P21A0 |
|
P21A100 |
Cylinder 6 Air-Fuel Ratio Imbalance |
Comes on |
DTC stored |
SAE Code: P21A1 |
|
P21CF13 |
Cylinder 1 Injector "B" Circuit Open |
Comes on |
DTC stored |
SAE Code: P21CF |
|
P21D013 |
Cylinder 2 Injector "B" Circuit Open |
Comes on |
DTC stored |
SAE Code: P21D0 |
|
P21D113 |
Cylinder 3 Injector "B" Circuit Open |
Comes on |
DTC stored |
SAE Code: P21D1 |
|
P21D213 |
Cylinder 4 Injector "B" Circuit Open |
Comes on |
DTC stored |
SAE Code: P21D2 |
|
P21D313 |
Cylinder 5 Injector "B" Circuit Open |
Comes on |
DTC stored |
SAE Code: P21D3 |
|
P21D413 |
Cylinder 6 Injector "B" Circuit Open |
Comes on |
DTC stored |
SAE Code: P21D4 |
|
P223711 |
A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P2238 |
|
P223712 |
A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Short to Battery |
Comes on |
DTC stored |
SAE Code: P2239 |
|
P223714 |
A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Short to Ground or Open |
Comes on |
DTC stored |
SAE Code: P2237 |
|
P223716 |
A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Voltage Below Threshold |
Comes on |
DTC stored |
SAE Code: P2238 |
|
P223717 |
A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Voltage Above Threshold |
Comes on |
DTC stored |
SAE Code: P2239 |
|
P22371B |
A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Resistance Above Threshold |
Comes on |
DTC stored |
SAE Code: P2238 |
|
P224011 |
A/F (O2) Sensor Positive Current Control Bank 2 Sensor 1 Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P2241 |
|
P224012 |
A/F (O2) Sensor Positive Current Control Bank 2 Sensor 1 Circuit Short to Battery |
Comes on |
DTC stored |
SAE Code: P2242 |
|
P224013 |
A/F (O2) Sensor Positive Current Control Bank 2 Sensor 1 Circuit Open |
Comes on |
DTC stored |
SAE Code: P2240 |
|
P224016 |
A/F (O2) Sensor Positive Current Control Bank 2 Sensor 1 Circuit Voltage Below Threshold |
Comes on |
DTC stored |
SAE Code: P2241 |
|
P224017 |
A/F (O2) Sensor Positive Current Control Bank 2 Sensor 1 Circuit Voltage Above Threshold |
Comes on |
DTC stored |
SAE Code: P2242 |
|
P22401A |
A/F (O2) Sensor Positive Current Control Bank 2 Sensor 1 Circuit Resistance Below Threshold |
Comes on |
DTC stored |
SAE Code: P2241 |
|
P225111 |
O2 Sensor Negative Current Control Bank 1 Sensor 1 Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P2252 |
|
P225112 |
O2 Sensor Negative Current Control Bank 1 Sensor 1 Circuit Short to Battery |
Comes on |
DTC stored |
SAE Code: P2253 |
|
P225411 |
O2 Sensor Negative Current Control Bank 2 Sensor 1 Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P2255 |
|
P225412 |
O2 Sensor Negative Current Control Bank 2 Sensor 1 Circuit Short to Battery |
Comes on |
DTC stored |
SAE Code: P2256 |
|
P24007E |
Evaporative Emission System Leak Detection Pump Control Circuit Actuator Stuck On |
Comes on |
DTC stored |
SAE Code: P2402 |
|
P24007F |
Evaporative Emission System Leak Detection Pump Control Circuit Actuator Stuck Off |
Comes on |
DTC stored |
SAE Code: P2401 |
|
P24187E |
Evaporative Emission System Switching Valve Control Circuit Actuator Stuck On |
Comes on |
DTC stored |
SAE Code: P2419 |
|
P24187F |
Evaporative Emission System Switching Valve Control Circuit Actuator Stuck Off |
Comes on |
DTC stored |
SAE Code: P2420 |
|
P261029 |
ECM/PCM Engine Off Timer Performance Signal Invalid |
Comes on |
DTC stored |
SAE Code: P2610 |
|
P261093 |
ECM/PCM Engine Off Timer Performance No Operation |
Comes on |
DTC stored |
SAE Code: P2610 |
|
U010187 |
Lost Communication with TCM Missing Message |
Comes on |
DTC stored |
SAE Code: U0101 |
|
U015587 |
Lost Communication with Instrument Panel Cluster (IPC) Control Module Missing Message |
Comes on |
DTC stored |
SAE Code: U0155 |
