Evaporative Emission System Pressure / Intake Air Pressure Signal Compare Failure (P106A62,P106C62). Fuel Rail Pressure Sensor (Low) Circuit Short to Ground (P107A11). Fuel Rail Pressure Sensor (Low)
Evaporative Emission System Pressure / Intake Air Pressure Signal Compare Failure (P106A62,P106C62)
DESCRIPTION
Those DTCs are designed to detect a deviation in the output characteristics of a pressure sensor.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
P106A62 |
Evaporative Emission System Pressure / Intake Air Pressure Signal Compare Failure |
The difference between the pressure of the canister pressure sensor (Vapor Pressure Pump*) and manifold absolute pressure sensor (Intake Manifold Absolute Pressure*) is higher than 8.69 kPa (1.26 psi) (2 trip detection logic). |
|
Comes on |
DTC stored |
SAE Code: P106A |
P106C62 |
Evaporative Emission System Pressure/Barometric Pressure Signal Compare Failure |
The difference between the pressure of the canister pressure sensor (Vapor Pressure Pump*) and atmospheric pressure sensor (Atmospheric Pressure*) is higher than 7.89 kPa (1.14 psi) (2 trip detection logic). |
|
Comes on |
DTC stored |
SAE Code: P106C |
*: Data List name
MONITOR DESCRIPTION
Those DTCs are stored when a deviation from pressure sensor characteristics is detected.
The pressure sensors* are checked approximately 50 minutes after the power switch is turned off. If the pressures detected by the pressure sensors* differ by a certain amount, the MIL is illuminated and a DTC is stored (2 trip detection logic).
HINT:
- *: P106A62 checks the canister pressure sensor and the manifold absolute pressure sensor. P106C62 checks the canister pressure sensor and atmospheric pressure sensor.
- Correct judgment may not be possible when the altitude is 4000 m (13120 ft.) or more.
MONITOR STRATEGY
Related DTCs |
P106A: Canister pressure sensor - manifold absolute pressure sensor rationality P106C: Canister pressure sensor - barometric pressure sensor rationality |
Required Sensors/Components (Main) |
Canister pressure sensor Atmospheric pressure sensor (ECM) Manifold absolute pressure sensor |
Required Sensors/Components (Related) |
- |
Frequency of Operation |
Continuous |
Duration |
P106A: Within 65 seconds P106C: - |
MIL Operation |
2 driving cycles |
Sequence of Operation |
None |
TYPICAL ENABLING CONDITIONS
P106AMonitor runs whenever the following DTCs are not stored |
P0106, P0107, P0108 (Manifold absolute pressure) P0401 (EGR system) P0452, P0453 (Evaporative emission system pressure sensor) |
Time after power switch off |
50 minutes |
Time after ECM started by soak-timer |
60 seconds or more |
Auxiliary battery voltage |
8 V or higher |
Intake air temperature |
-10°C (14°F) or higher |
Engine coolant temperature |
-10°C (14°F) or higher |
Time after power switch off |
50 minutes |
Time after ECM started by soak-timer |
60 seconds or more |
Auxiliary battery voltage |
8 V or higher |
Intake air temperature |
-10°C (14°F) or higher |
Engine coolant temperature |
-10°C (14°F) or higher |
EVAP system pressure sensor malfunction (P0451, P0452, P0453) |
Not detected |
TYPICAL MALFUNCTION THRESHOLDS
P106ADifference between canister pressure and manifold absolute pressure |
Higher than 8.69 kPa (1.26 psi) |
Difference between canister pressure and atmospheric pressure |
Higher than 7.89 kPa (1.14 psi) |
CONFIRMATION DRIVING PATTERN
HINT:
- After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here

- When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here

- Connect the Techstream to the DLC3.
- Turn the power switch on (IG).
- Turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the power switch off and wait for at least 30 seconds.
- Turn the power switch on (IG).
- Turn the Techstream on.
- Put the engine in Inspection Mode (Maintenance Mode).
Click here

- Start the engine and idle for 10 seconds or more [A].
- Turn the power switch off.
- Leave the power switch off for 55 minutes [B].
- Turn the power switch on (IG).
- Turn the Techstream on.
- Enter the following menus: Powertrain / Engine / Trouble Codes [C].
- Read the pending DTCs.
HINT:
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
- Enter the following menus: Powertrain / Engine / Utility / All Readiness.
- Input the DTC: P106A62 or P106C62.
- Check the DTC judgment result.
Techstream Display
Description
NORMAL
- DTC judgment completed
- System normal
ABNORMAL
- DTC judgment completed
- System abnormal
INCOMPLETE
- DTC judgment not completed
- Perform driving pattern after confirming DTC enabling conditions
HINT:
- If the judgment result is NORMAL, the system is normal.
- If the judgment result is ABNORMAL, the system is malfunctioning.
- If the judgment result is INCOMPLETE, perform steps [A] through [C] again.
- [A] to [C]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- When clearing the permanent DTCs, do not disconnect the cable from the auxiliary battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.
NOTICE:
- Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the Freeze Frame Data and Vehicle Control History can be useful for troubleshooting.
Click here

(Select Powertrain in Health Check and then check the time stamp data.)
Click here

- If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.
Click here

HINT:
- Refer to "Data List / Active Test" [Atmospheric Pressure, Intake Manifold Absolute Pressure and Vapor Pressure Pump].
Click here

- Read Freeze Frame Data using the Techstream. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P106A62 AND/OR P106C62)
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine / Trouble Codes.
(e) Read the DTCs.
Powertrain > Engine > Trouble CodesResult | Proceed to |
|---|---|
DTC P106A62 is output |
A |
DTC P106C62 is output |
B |
DTC P106A62 and P106C62 are output |
C |
DTC P106A62 and/or P106C62 and other DTCs are output |
D |
HINT:
If any DTCs other than P106A62 and/or P106C62 are output, troubleshoot those DTCs first.
| B | GO TO STEP 3 |
| C | GO TO STEP 4 |
| D | GO TO DTC CHART |
|
REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
(a) Replace the manifold absolute pressure sensor.
Click here ![]()
| NEXT | GO TO STEP 5 |
REPLACE ECM (ATMOSPHERIC PRESSURE SENSOR)
(a) Replace the ECM (atmospheric pressure sensor).
Click here ![]()
| NEXT | GO TO STEP 5 |
REPLACE CANISTER PUMP MODULE
(a) Replace the canister pump module.
Click here ![]()
|
CLEAR DTC
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Clear the DTCs.
Powertrain > Engine > Clear DTCs(e) Turn the power switch off and wait for at least 30 seconds.
|
CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
(a) Turn the power switch on (IG).
(b) Turn the Techstream on.
(c) Enter the following menus: Powertrain / Engine / Data List / Atmospheric Pressure, Vapor Pressure Pump and Intake Manifold Absolute Pressure.
Powertrain > Engine > Data ListTester Display |
|---|
Atmospheric Pressure |
Intake Manifold Absolute Pressure |
Vapor Pressure Pump |
(d) Confirm that the difference between Intake Manifold Absolute Pressure and Vapor Pressure Pump is 8.69 kPa (1.26 psi) or less.
(e) Confirm that the difference between Atmospheric Pressure and Vapor Pressure Pump is 7.89 kPa (1.14 psi) or less.
| NEXT | END |
Fuel Rail Pressure Sensor (Low) Circuit Short to Ground (P107A11)
DESCRIPTION
The fuel pressure sensor (for low pressure side) replaces the fuel pressure with electrical signals and outputs them to the ECM. The ECM controls the optimal fuel pressure for the operation conditions to reduce the fuel pump power consumption and improve fuel economy.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
P107A11 |
Fuel Rail Pressure Sensor (Low) Circuit Short to Ground |
The fuel pressure sensor (for low pressure side) output voltage is less than 0.43 V for 3 seconds or more (1 trip detection logic). |
|
Comes on |
DTC stored |
SAE Code: P107C |
HINT:
When this DTC is output, check the fuel pressure (for low pressure side) in the Data List. Enter the following menus: Powertrain / Engine / Data List / Fuel Pressure (Low).
DTC No. | Fuel Pressure (Low) | Malfunction |
|---|---|---|
P107A11 |
Approximately 0 kPa |
|
If the Data List value is normal it may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.
Click here ![]()
MONITOR DESCRIPTION
This DTC is stored if the fuel pressure sensor (for low pressure side) output voltage is out of the standard range due to an open or short in the sensor circuit.
MONITOR STRATEGY
Related DTCs |
P107C: Fuel rail pressure sensor range check (Low voltage) |
Required Sensors/Components (Main) |
Fuel pressure sensor (for low pressure side) |
Required Sensors/Components (Related) |
- |
Frequency of Operation |
Continuous |
Duration |
3 seconds |
MIL Operation |
Immediate |
Sequence of Operation |
None |
TYPICAL ENABLING CONDITIONS
Monitor runs whenever the following DTCs are not stored |
None |
All of the following conditions are met |
- |
Auxiliary battery voltage |
8 V or higher |
Power switch |
On (IG) |
Time after engine start |
2 seconds or more |
TYPICAL MALFUNCTION THRESHOLDS
Fuel rail pressure sensor voltage |
Less than 0.43 V |
CONFIRMATION DRIVING PATTERN
HINT:
- After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here

- When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here

- Connect the Techstream to the DLC3.
- Turn the power switch on (IG).
- Turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the power switch off and wait for at least 30 seconds.
- Turn the power switch on (IG).
- Turn the Techstream on.
- Put the engine in Inspection Mode (Maintenance Mode).
Click here

- Start the engine.
- Idle the engine for 10 seconds or more [A].
- Enter the following menus: Powertrain / Engine / Trouble Codes [B].
- Read the pending DTCs.
HINT:
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
- Enter the following menus: Powertrain / Engine / Utility / All Readiness.
- Input the DTC: P107A11.
- Check the DTC judgment result.
Techstream Display
Description
NORMAL
- DTC judgment completed
- System normal
ABNORMAL
- DTC judgment completed
- System abnormal
INCOMPLETE
- DTC judgment not completed
- Perform driving pattern after confirming DTC enabling conditions
HINT:
- If the judgment result is NORMAL, the system is normal.
- If the judgment result is ABNORMAL, the system has a malfunction.
- If the judgment result is INCOMPLETE, perform steps [A] through [B] again.
- [A] to [B]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- When clearing the permanent DTCs, do not disconnect the cable from the auxiliary battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.
WIRING DIAGRAM
NOTICE:
- Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the Freeze Frame Data and Vehicle Control History can be useful for troubleshooting.
Click here

(Select Powertrain in Health Check and then check the time stamp data.)
Click here

- If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.
Click here

HINT:
Read Freeze Frame Data using the Techstream. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
CHECK HARNESS AND CONNECTOR
*a |
Front view of wire harness connector (to Fuel Pressure Sensor (for Low Pressure Side)) |
HINT:
Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.
(a) Disconnect the fuel pressure sensor (for low pressure side) connector.
(b) Turn the power switch on (IG).
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
D5-1 (VC) - D5-3 (E2) |
Power switch on (IG) |
4.75 to 5.25 V |
D5-2 (PFL) - D5-3 (E2) |
Power switch on (IG) |
4.4 to 5.6 V |
(d) Turn the power switch off and wait for at least 30 seconds.
(e) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
D5-1 (VC) - D5-2 (PFL) |
Power switch off |
171 to 189 kΩ |
HINT:
Perform "Inspection After Repair" after replacing the fuel pressure sensor (for low pressure side).
Click here ![]()
| OK | REPLACE FUEL PRESSURE SENSOR (FOR LOW PRESSURE SIDE) |
|
CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR (FOR LOW PRESSURE SIDE) - ECM)
(a) Disconnect the fuel pressure sensor (for low pressure side) connector.
(b) Disconnect the ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
D5-1 (VC) - C55-84 (VCPF) |
Always |
Below 1 Ω |
D5-2 (PFL) or C55-107 (PFL) - Body ground and other terminals |
Always |
10 kΩ or higher |
| OK | REPLACE ECM |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
Fuel Rail Pressure Sensor (Low) Circuit Short to Battery or Open (P107A15)
DESCRIPTION
Refer to DTC P107A11.
Click here ![]()
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
P107A15 |
Fuel Rail Pressure Sensor (Low) Circuit Short to Battery or Open |
The fuel pressure sensor (for low pressure side) output voltage is higher than 4.85 V for 3 seconds or more (1 trip detection logic). |
|
Comes on |
DTC stored |
SAE Code: P107D |
HINT:
When this DTC is output, check the fuel pressure (for low pressure side) in the Data List. Enter the following menus: Powertrain / Engine / Data List / Fuel Pressure (Low).
DTC No. | Fuel Pressure (Low) | Malfunction |
|---|---|---|
P107A15 |
Approximately 750 kPa or higher |
|
If the Data List value is normal it may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.
Click here ![]()
MONITOR DESCRIPTION
This DTC is stored if the fuel pressure sensor (for low pressure side) output voltage is out of the standard range due to an open or short in the sensor circuit.
MONITOR STRATEGY
Related DTCs |
P107D: Fuel rail pressure sensor range check (High voltage) |
Required Sensors/Components (Main) |
Fuel pressure sensor (for low pressure side) |
Required Sensors/Components (Related) |
- |
Frequency of Operation |
Continuous |
Duration |
3 seconds |
MIL Operation |
Immediate |
Sequence of Operation |
None |
TYPICAL ENABLING CONDITIONS
Monitor runs whenever the following DTCs are not stored |
None |
Both of the following conditions are met |
- |
Auxiliary battery voltage |
8 V or higher |
Power switch |
On (IG) |
TYPICAL MALFUNCTION THRESHOLDS
Fuel rail pressure sensor voltage |
Higher than 4.85 V |
CONFIRMATION DRIVING PATTERN
HINT:
- After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here

- When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here

- Connect the Techstream to the DLC3.
- Turn the power switch on (IG).
- Turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the power switch off and wait for at least 30 seconds.
- Turn the power switch on (IG).
- Turn the Techstream on.
- Put the engine in Inspection Mode (Maintenance Mode).
Click here

- Start the engine.
- Idle the engine for 10 seconds or more [A].
- Enter the following menus: Powertrain / Engine / Trouble Codes [B].
- Read the pending DTCs.
HINT:
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
- Enter the following menus: Powertrain / Engine / Utility / All Readiness.
- Input the DTC: P107A15.
- Check the DTC judgment result.
Techstream Display
Description
NORMAL
- DTC judgment completed
- System normal
ABNORMAL
- DTC judgment completed
- System abnormal
INCOMPLETE
- DTC judgment not completed
- Perform driving pattern after confirming DTC enabling conditions
HINT:
- If the judgment result is NORMAL, the system is normal.
- If the judgment result is ABNORMAL, the system has a malfunction.
- If the judgment result is INCOMPLETE, perform steps [A] through [B] again.
- [A] to [B]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- When clearing the permanent DTCs, do not disconnect the cable from the auxiliary battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.
WIRING DIAGRAM
Refer to DTC P107A11.
Click here ![]()
NOTICE:
- Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the Freeze Frame Data and Vehicle Control History can be useful for troubleshooting.
Click here

(Select Powertrain in Health Check and then check the time stamp data.)
Click here

- If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.
Click here

HINT:
Read Freeze Frame Data using the Techstream. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
CHECK HARNESS AND CONNECTOR
*a |
Front view of wire harness connector (to Fuel Pressure Sensor (for Low Pressure Side)) |
HINT:
Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.
(a) Disconnect the fuel pressure sensor (for low pressure side) connector.
(b) Turn the power switch on (IG).
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
D5-1 (VC) - D5-3 (E2) |
Power switch on (IG) |
4.75 to 5.25 V |
D5-2 (PFL) - D5-3 (E2) |
Power switch on (IG) |
4.4 to 5.6 V |
(d) Turn the power switch off and wait for at least 30 seconds.
(e) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
D5-3 (E2) - Body ground |
Power switch off |
Below 1 Ω |
D5-1 (VC) - D5-2 (PFL) |
Power switch off |
171 to 189 kΩ |
HINT:
Perform "Inspection After Repair" after replacing the fuel pressure sensor (for low pressure side).
Click here ![]()
| OK | REPLACE FUEL PRESSURE SENSOR (FOR LOW PRESSURE SIDE) |
|
CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR (FOR LOW PRESSURE SIDE) - ECM)
(a) Disconnect the fuel pressure sensor (for low pressure side) connector.
(b) Disconnect the ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
D5-3 (E2) - C55-61 (EPFL) |
Always |
Below 1 Ω |
D5-2 (PFL) - C55-107 (PFL) |
Always |
Below 1 Ω |
D5-2 (PFL) or C55-107 (PFL) - Other terminals |
Always |
10 kΩ or higher |
| OK | REPLACE ECM |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |