Diagnosis System. Diagnostic Trouble Code Chart. Dtc Check / Clear
Diagnosis System
DIAGNOSIS SYSTEM
DESCRIPTION
When troubleshooting OBD II (On-Board Diagnostics) vehicles, the Techstream (complying with SAE J1978) must be connected to the DLC3 (Data Link Connector 3) of the vehicle. Various data in the vehicle's ECM (Engine Control Module) can be then read.
OBD II regulations require that the vehicle's on-board computer illuminates the MIL (Malfunction Indicator Lamp) on the instrument panel when the computer detects a malfunction in:
- The emission control system and components.
- The powertrain control components (which affect vehicle emissions).
- The computer itself.
In addition, the applicable DTCs prescribed by SAE J2012 are stored in the ECM memory. If the malfunction does not recur in 3 consecutive trips, the MIL turns off automatically but the DTCs remain stored in the ECM memory.
To check the DTCs, connect the Techstream to the DLC3. The Techstream displays output DTCs, Freeze Frame Data, and a variety of engine data. The DTCs and Freeze Frame Data can be cleared with the Techstream. In order to enhance OBD function on vehicles and develop the Off-Board diagnosis system, Controller Area Network (CAN) communication is used in this system. CAN is a network which uses a pair of data transmission lines spanning multiple computers and sensors. It allows for high speed communications between the systems and simplification of the wire harness connections.
NORMAL MODE AND CHECK MODE
The diagnosis system operates in normal mode during normal vehicle use. In normal mode, 2 trip detection logic is used to ensure accurate detection of malfunctions. Check mode is also available as an option for technicians. In check mode, 1 trip detection logic is used for duplicating malfunction symptoms and increasing the system's ability to detect malfunctions, including intermittent problems (Techstream only).
2 TRIP DETECTION LOGIC
When a malfunction is first detected, the malfunction is temporarily stored in the ECM memory (1st trip). If the same malfunction is detected during the subsequent drive cycle, the MIL is illuminated (2nd trip).
DLC3 (Data Link Connector 3)
(a) Check the DLC3.
Click here ![]()
FREEZE FRAME DATA
The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
AUXILIARY BATTERY VOLTAGE
Standard Voltage:
11 to 16 V
If the voltage is less than 11 V, recharge or replace the auxiliary battery.
MIL (Malfunction Indicator Lamp)
(a) The MIL is illuminated when the power switch is turned on (IG) (with the engine is not running).
(b) The MIL will turn off when the power switch is turned on (READY). If the MIL remains illuminated, the diagnosis system has detected a malfunction or abnormality in the system.
HINT:
If the MIL does not illuminate when the power switch is turned on (IG), check the MIL circuit.
Click here ![]()
ALL READINESS
HINT:
- With "All Readiness", you can use the Techstream to check whether or not DTC judgment has been completed.
- You should check "All Readiness" after simulating malfunction symptoms or for validation after finishing repairs.
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Clear the DTCs.
Powertrain > Engine > Clear DTCs(e) Turn the power switch off and wait for at least 30 seconds.
(f) Turn the power switch on (IG).
(g) Turn the Techstream on.
(h) Perform the DTC judgment driving pattern to run the DTC judgment.
(i) Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Powertrain > Engine > UtilityAll Readiness
(j) Input the DTCs to be confirmed.
(k) Check the DTC judgment result.
Techstream Display | Description |
|---|---|
NORMAL |
|
ABNORMAL |
|
INCOMPLETE |
|
DIAGNOSIS RELATED INFORMATION
HINT:
- If the detection conditions of certain DTCs are met before a malfunction can be confirmed, the ECM will store Diagnosis Related Information. Vehicle condition information from when the detection conditions were met can be checked using the Diagnosis Related Information. Diagnosis Related Information should be used as a reference only, and should not be relied upon solely when determining whether a part is faulty or not.
- Clearing DTCs will also clear Diagnosis Related Information.
- DTCs and Diagnosis Related Information are saved in the Techstream at the same time.
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine / Utility / Diagnosis Related Information.
Powertrain > Engine > UtilityDiagnosis Related Information
(e) Select a Diagnosis Related Information item to display it' s details.
Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART
SFI SystemDTC No. | Detection Item | MIL | Memory | Note | Link |
|---|---|---|---|---|---|
P001001 |
Camshaft Position "A" Actuator Bank 1 General Electrical Failure |
Comes on |
DTC stored |
SAE Code: P0010 |
|
P001100 |
Camshaft Position "A" - Timing Over-Advanced or System Performance Bank 1 |
Comes on |
DTC stored |
SAE Code: P0011 |
|
P001200 |
Camshaft Position "A" - Timing Over-Retarded Bank 1 |
Comes on |
DTC stored |
SAE Code: P0012 |
|
P001313 |
Camshaft Position "B" - Actuator Bank 1 Circuit Open |
Comes on |
DTC stored |
SAE Code: P0013 |
|
P001400 |
Camshaft Position "B" - Timing Over-Advanced or System Performance Bank 1 |
Comes on |
DTC stored |
SAE Code: P0014 |
|
P001500 |
Camshaft Position "B" - Timing Over-Retarded Bank 1 |
Comes on |
DTC stored |
SAE Code: P0015 |
|
P001600 |
Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor A |
Comes on |
DTC stored |
SAE Code: P0016 |
|
P001700 |
Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor B |
Comes on |
DTC stored |
SAE Code: P0017 |
|
P003012 |
HO2S Heater Control Bank 1 Sensor 1 Circuit Short to Battery |
Comes on |
DTC stored |
SAE Code: P0032 |
|
P003013 |
HO2S Heater Control Bank 1 Sensor 1 Circuit Open |
Comes on |
DTC stored |
SAE Code: P0031 |
|
P003612 |
HO2S Heater Control Circuit Bank 1 Sensor 2 Circuit Short to Battery |
Comes on |
DTC stored |
SAE Code: P0038 |
|
P003613 |
A/F (O2) Heater Control Circuit Bank 1 Sensor 2 Circuit Open |
Comes on |
DTC stored |
SAE Code: P0037 |
|
P006900 |
Manifold Absolute Pressure - Barometric Pressure Correlation |
Comes on |
DTC stored |
SAE Code: P0069 |
|
P008700 |
Fuel Rail / System Pressure - Too Low |
Comes on |
DTC stored |
SAE Code: P0087 |
|
P008800 |
Fuel Rail / System Pressure - Too High |
Comes on |
DTC stored |
SAE Code: P0088 |
|
P008A00 |
Low Pressure Fuel System Pressure - Too Low |
Does not come on |
DTC stored |
SAE Code: P008A |
|
P008B00 |
Low Pressure Fuel System Pressure - Too High |
Does not come on |
DTC stored |
SAE Code: P008B |
|
P00B111 |
Radiator Coolant Temperature Sensor Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P00B3 |
|
P00B115 |
Radiator Coolant Temperature Sensor Circuit Short to Battery or Open |
Comes on |
DTC stored |
SAE Code: P00B4 |
|
P00B162 |
Radiator Coolant Temperature Sensor Signal Compare Failure |
Comes on |
DTC stored |
SAE Code: P00B2 |
|
P00D562 |
A/F (O2) Sensor Correlation Bank 1 Sensor 1/Bank 1 Sensor 2 Signal Compare Failure |
Comes on |
DTC stored |
SAE Code: P00D5 |
|
P010012 |
Mass or Volume Air Flow Sensor "A" Circuit Short to Battery |
Comes on |
DTC stored |
SAE Code: P0103 |
|
P010014 |
Mass or Volume Air Flow Sensor "A" Circuit Short to Ground or Open |
Comes on |
DTC stored |
SAE Code: P0102 |
|
P010064 |
Mass or Volume Air Flow Sensor "A" Signal Plausibility Failure |
Comes on |
DTC stored |
SAE Code: P0101 |
|
P010511 |
Manifold Absolute Pressure / Barometric Pressure Sensor Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P0107 |
|
P010515 |
Manifold Absolute Pressure / Barometric Pressure Sensor Circuit Short to Battery or Open |
Comes on |
DTC stored |
SAE Code: P0108 |
|
P01052A |
Manifold Absolute Pressure / Barometric Pressure Sensor Signal Stuck in Range |
Comes on |
DTC stored |
SAE Code: P0106 |
|
P011011 |
Intake Air Temperature Sensor 1 Bank 1 Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P0112 |
|
P011015 |
Intake Air Temperature Sensor 1 Bank 1 Circuit Short to Battery or Open |
Comes on |
DTC stored |
SAE Code: P0113 |
|
P01102A |
Intake Air Temperature Sensor 1 Bank 1 Signal Stuck in Range |
Comes on |
DTC stored |
SAE Code: P0111 |
|
P011511 |
Engine Coolant Temperature Sensor 1 Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P0117 |
|
P011515 |
Engine Coolant Temperature Sensor 1 Circuit Short to Battery or Open |
Comes on |
DTC stored |
SAE Code: P0118 |
|
P01152A |
Engine Coolant Temperature Sensor 1 Signal Stuck in Range |
Comes on |
DTC stored |
SAE Code: P0116 |
|
P012011 |
Throttle / Pedal Position Sensor / Switch "A" Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P0122 |
|
P012015 |
Throttle / Pedal Position Sensor / Switch "A" Circuit Short to Battery or Open |
Comes on |
DTC stored |
SAE Code: P0123 |
|
P01201C |
Throttle / Pedal Position Sensor / Switch "A" Circuit Voltage Out of Range |
Comes on |
DTC stored |
SAE Code: P0121 |
|
P012500 |
Insufficient Coolant Temperature for Closed Loop Fuel Control |
Comes on |
DTC stored |
SAE Code: P0125 |
|
P012800 |
Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature) |
Comes on |
DTC stored |
SAE Code: P0128 |
|
P012807 |
Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature) Mechanical Failure |
Comes on |
DTC stored |
SAE Code: P0128 |
|
P012F62 |
Engine Coolant Temperature/Engine Oil Temperature Signal Compare Failure |
Comes on |
DTC stored |
SAE Code: P012F |
|
P013616 |
A/F (O2) Sensor Circuit Bank 1 Sensor 2 Circuit Current (Voltage) Below Threshold |
Comes on |
DTC stored |
SAE Code: P0136 |
|
P013A7C |
A/F Sensor - Rich to Lean Bank 1 Sensor 2 Slow Response |
Comes on |
DTC stored |
SAE Code: P013A |
|
P014C00 |
O2 Sensor Slow Response - Rich to Lean Bank 1 Sensor 1 |
Comes on |
DTC stored |
SAE Code: P014C |
|
P014D00 |
O2 Sensor Slow Response - Lean to Rich Bank 1 Sensor 1 |
Comes on |
DTC stored |
SAE Code: P014D |
|
P015A00 |
O2 Sensor Delayed Response - Rich to Lean Bank 1 Sensor 1 |
Comes on |
DTC stored |
SAE Code: P015A |
|
P015B00 |
O2 Sensor Delayed Response - Lean to Rich Bank 1 Sensor 1 |
Comes on |
DTC stored |
SAE Code: P015B |
|
P017100 |
System Too Lean Bank 1 |
Comes on |
DTC stored |
SAE Code: P0171 |
|
P017200 |
System Too Rich Bank 1 |
Comes on |
DTC stored |
SAE Code: P0172 |
|
P019011 |
Fuel Rail Pressure Sensor "A" Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P0192 |
|
P019015 |
Fuel Rail Pressure Sensor "A" Circuit Short to Battery or Open |
Comes on |
DTC stored |
SAE Code: P0193 |
|
P01902A |
Fuel Rail Pressure Sensor "A" Signal Stuck in Range |
Comes on |
DTC stored |
SAE Code: P0191 |
|
P019064 |
Fuel Rail Pressure Sensor "A" Signal Plausibility Failure |
Comes on |
DTC stored |
SAE Code: P0191 |
|
P019511 |
Engine Oil Temperature Sensor Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P0197 |
|
P019515 |
Engine Oil Temperature Sensor Circuit Short to Battery or Open |
Comes on |
DTC stored |
SAE Code: P0198 |
|
P020113 |
Cylinder 1 Injector "A" Circuit Open |
Comes on |
DTC stored |
SAE Code: P0201 |
|
P020213 |
Cylinder 2 Injector "A" Circuit Open |
Comes on |
DTC stored |
SAE Code: P0202 |
|
P020313 |
Cylinder 3 Injector "A" Circuit Open |
Comes on |
DTC stored |
SAE Code: P0203 |
|
P020413 |
Cylinder 4 Injector "A" Circuit Open |
Comes on |
DTC stored |
SAE Code: P0204 |
|
P022011 |
Throttle/Pedal Position Sensor/Switch "B" Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P0222 |
|
P022015 |
Throttle/Pedal Position Sensor/Switch "B" Circuit Short to Battery or Open |
Comes on |
DTC stored |
SAE Code: P0223 |
|
P030000 |
Random/Multiple Cylinder Misfire Detected |
Comes on/Blinks* *: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored |
SAE Code: P0300 |
|
P030027 |
Random/Multiple Cylinder Misfire Detected (Emission) Signal Rate of Change Above Threshold |
Comes on |
DTC stored |
SAE Code: - |
|
P030085 |
Random / Multiple Cylinder Misfire Detected (Over Temperature) Signal Above Allowable Range |
Comes on/Blinks* *: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored |
SAE Code: - |
|
P030100 |
Cylinder 1 Misfire Detected |
Comes on/Blinks* *: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored |
SAE Code: P0301 |
|
P030200 |
Cylinder 2 Misfire Detected |
Comes on/Blinks* *: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored |
SAE Code: P0302 |
|
P030300 |
Cylinder 3 Misfire Detected |
Comes on/Blinks* *: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored |
SAE Code: P0303 |
|
P030400 |
Cylinder 4 Misfire Detected |
Comes on/Blinks* *: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored |
SAE Code: P0304 |
|
P032511 |
Knock Sensor 1 Bank 1 or Single Sensor Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P0327 |
|
P032515 |
Knock Sensor 1 Bank 1 or Single Sensor Circuit Short to Battery or Open |
Comes on |
DTC stored |
SAE Code: P0328 |
|
P033511 |
Crankshaft Position Sensor "A" Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P0337 |
|
P033515 |
Crankshaft Position Sensor "A" Circuit Short to Battery or Open |
Comes on |
DTC stored |
SAE Code: P0338 |
|
P03352A |
Crankshaft Position Sensor "A" Signal Stuck in Range |
Comes on |
DTC stored |
SAE Code: P0335 |
|
P033531 |
Crankshaft Position Sensor "A" No Signal |
Comes on |
DTC stored |
SAE Code: P0335 |
|
P034011 |
Camshaft Position Sensor "A" Bank 1 or Single Sensor Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P0342 |
|
P034015 |
Camshaft Position Sensor "A" Bank 1 or Single Sensor Circuit Short to Battery or Open |
Comes on |
DTC stored |
SAE Code: P0343 |
|
P034031 |
Camshaft Position Sensor "A" Bank 1 or Single Sensor No Signal |
Comes on |
DTC stored |
SAE Code: P0340 |
|
P036511 |
Camshaft Position Sensor "B" Bank 1 Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P0367 |
|
P036515 |
Camshaft Position Sensor "B" Bank 1 Circuit Short to Battery or Open |
Comes on |
DTC stored |
SAE Code: P0368 |
|
P03652A |
Camshaft Position Sensor "B" Bank 1 Signal Stuck in Range |
Comes on |
DTC stored |
SAE Code: P0365 |
|
P036531 |
Camshaft Position Sensor "B" Bank 1 No Signal |
Comes on |
DTC stored |
SAE Code: P0365 |
|
P04019C |
Exhaust Gas Recirculation "A" Low / Insufficient Flow |
Comes on |
DTC stored |
SAE Code: P0401 |
|
P040318 |
Exhaust Gas Recirculation "A" Circuit Current Below Threshold |
Comes on |
DTC stored |
SAE Code: P0489 |
|
P040319 |
Exhaust Gas Recirculation "A" Circuit Current Above Threshold |
Comes on |
DTC stored |
SAE Code: P0490 |
|
P042000 |
Catalyst System Efficiency Below Threshold Bank 1 |
Comes on |
DTC stored |
SAE Code: P0420 |
|
P043E00 |
Evaporative Emission System Leak Detection Reference Orifice Low Flow |
Comes on |
DTC stored |
SAE Code: P043E |
|
P043F00 |
Evaporative Emission System Leak Detection Reference Orifice High Flow |
Comes on |
DTC stored |
SAE Code: P043F |
|
P04417E |
Evaporative Emission System Incorrect Purge Flow Actuator Stuck On |
Comes on |
DTC stored |
SAE Code: P0441 |
|
P04417F |
Evaporative Emission System Incorrect Purge Flow Actuator Stuck Off |
Comes on |
DTC stored |
SAE Code: P0441 |
|
P04419C |
Evaporative Emission System Incorrect Purge Flow Low/Insufficient Flow |
Comes on |
DTC stored |
SAE Code: P0441 |
|
P045011 |
Evaporative Emission System Pressure Sensor/Switch Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P0452 |
|
P045015 |
Evaporative Emission System Pressure Sensor/Switch Circuit Short to Battery or Open |
Comes on |
DTC stored |
SAE Code: P0453 |
|
P04502F |
Evaporative Emission System Pressure Sensor/Switch Signal Erratic |
Comes on |
DTC stored |
SAE Code: P0451 |
|
P050500 |
Idle Control System |
Comes on |
DTC stored |
SAE Code: P0505 |
|
P050A00 |
Cold Start Idle Control System Performance |
Comes on |
DTC stored |
SAE Code: P050A |
|
P050B00 |
Cold Start Ignition Timing Performance |
Comes on |
DTC stored |
SAE Code: P050B |
|
P052012 |
Engine Oil Pressure Sensor/Switch "A" Circuit Short to Battery |
Comes on |
DTC stored |
SAE Code: P0523 |
|
P052014 |
Engine Oil Pressure Sensor/Switch "A" Circuit Short to Ground or Open |
Comes on |
DTC stored |
SAE Code: P0522 |
|
P052024 |
Engine Oil Pressure Sensor/Switch "A" Signal Stuck High |
Comes on |
DTC stored |
SAE Code: P0521 |
|
P05202A |
Engine Oil Pressure Sensor/Switch "A" Signal Stuck in Range |
Comes on |
DTC stored |
SAE Code: P0521 |
|
P052477 |
Engine Oil Pressure Too Low (Severe) |
Comes on |
DTC stored |
SAE Code: P0524 |
|
P056014 |
System Voltage Circuit Short to Ground or Open |
Comes on |
DTC stored |
SAE Code: P0562 |
|
P059712 |
Thermostat Heater Control Circuit Short to Battery |
Comes on |
DTC stored |
SAE Code: P0599 |
|
P059714 |
Thermostat Heater Control Circuit Short to Ground or Open |
Comes on |
DTC stored |
SAE Code: P0598 |
|
P059F73 |
Active Grille Air Shutter "A" Actuator Stuck Closed |
Comes on |
DTC stored |
SAE Code: P059F |
|
P05A072 |
Active Grille Air Shutter "A" Actuator Stuck Open |
Comes on |
DTC stored |
SAE Code: P05A0 |
|
P05A074 |
Active Grille Air Shutter "A" Actuator Slipping |
Comes on |
DTC stored |
SAE Code: P05A0 |
|
P05A211 |
Active Grille Air Shutter "A" Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P05A5 |
|
P05A212 |
Active Grille Air Shutter "A" Circuit Short to Battery |
Comes on |
DTC stored |
SAE Code: P05A4 |
|
P05A213 |
Active Grille Air Shutter "A" Circuit Open |
Comes on |
DTC stored |
SAE Code: P05A2 |
|
P05A27E |
Active Grille Air Shutter "A" Actuator Stuck On |
Comes on |
DTC stored |
SAE Code: P05A3 |
|
P05A27F |
Active Grille Air Shutter "A" Actuator Stuck Off |
Comes on |
DTC stored |
SAE Code: P05A3 |
|
P05B112 |
Active Grille Air Shutter "B" Circuit Short to Battery |
Comes on |
DTC stored |
SAE Code: P05B3 |
|
P05B114 |
Active Grille Air Shutter "B" Circuit Short to Ground or Open |
Comes on |
DTC stored |
SAE Code: P05B4 |
|
P05B131 |
Active Grille Air Shutter "B" No Signal |
Comes on |
DTC stored |
SAE Code: P05B2 |
|
P060444 |
Internal Control Module Random Access Memory (RAM) Error Data Memory Failure |
Comes on |
DTC stored |
SAE Code: P0604 |
|
P060647 |
Control Module Processor Watchdog/Safety MCU Failure |
Comes on |
DTC stored |
SAE Code: P0606 |
|
P060747 |
Control Module Performance Bank 1 Watchdog/Safety MCU Failure |
Comes on |
DTC stored |
SAE Code: P0607 |
|
P060787 |
Control Module Performance Bank 1 Missing Message |
Comes on |
DTC stored |
SAE Code: P0607 |
|
P060E49 |
Internal Control Module Throttle Position Performance Internal Electronic Failure |
Comes on |
DTC stored |
SAE Code: P060E |
|
P062712 |
Fuel Pump "A" Control Circuit Short to Battery |
Comes on |
DTC stored |
SAE Code: P0629 |
|
P062714 |
Fuel Pump "A" Control Circuit Short to Ground or Open |
Comes on |
DTC stored |
SAE Code: P0628 |
|
P062D13 |
Fuel Injector Driver Circuit Performance Bank 1 Circuit Open |
Comes on |
DTC stored |
SAE Code: P062D |
|
P062F44 |
Internal Control Module EEPROM Data Memory Failure |
Comes on |
DTC stored |
SAE Code: P062F |
|
P063051 |
VIN Not Programmed |
Comes on |
DTC stored |
SAE Code: P0630 |
|
P064A49 |
Fuel Pump Control Module Internal Electronic Failure |
Comes on |
DTC stored |
SAE Code: P064A |
|
P065714 |
Actuator Supply Voltage "A" Circuit Short to Ground or Open |
Comes on |
DTC stored |
SAE Code: P0658 |
|
P06579E |
Actuator Supply Voltage "A" Stuck On |
Comes on |
DTC stored |
SAE Code: P0657 |
|
P06AB11 |
Control Module Internal Temperature Sensor "B" Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P06AD |
|
P06AB15 |
Control Module Internal Temperature Sensor "B" Circuit Short to Battery or Open |
Comes on |
DTC stored |
SAE Code: P06AE |
|
P06DA13 |
Engine Oil Pressure Control Circuit Open |
Does not come on |
DTC stored |
SAE Code: P06DA |
|
P101A9E |
A/F Sensor Heater Performance Bank 1 Sensor 1 Stuck On |
Comes on |
DTC stored |
SAE Code: P101D |
|
P102A9E |
O2 Sensor Heater Performance Bank 1 Sensor 2 Stuck On |
Comes on |
DTC stored |
SAE Code: P102D |
|
P106A62 |
Evaporative Emission System Pressure / Intake Air Pressure Signal Compare Failure |
Comes on |
DTC stored |
SAE Code: P106A |
|
P106C62 |
Evaporative Emission System Pressure/Barometric Pressure Signal Compare Failure |
Comes on |
DTC stored |
SAE Code: P106C |
|
P107A11 |
Fuel Rail Pressure Sensor (Low) Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P107C |
|
P107A15 |
Fuel Rail Pressure Sensor (Low) Circuit Short to Battery or Open |
Comes on |
DTC stored |
SAE Code: P107D |
|
P107A2A |
Fuel Rail Pressure Sensor (Low) Signal Stuck in Range |
Comes on |
DTC stored |
SAE Code: P107B |
|
P107A64 |
Fuel Rail Pressure Sensor (Low) Signal Plausibility Failure |
Comes on |
DTC stored |
SAE Code: P107B |
|
P111C62 |
Control Module Internal Temperature Sensor/Intake Air Temperature Sensor Signal Compare Failure |
Comes on |
DTC stored |
SAE Code: P111C |
|
P117000 |
Fuel Performance/Port Injector |
Does not come on |
DTC stored |
SAE Code: P1170 |
|
P117B00 |
Fuel Performance/Direct Injector |
Does not come on |
DTC stored |
SAE Code: P117B |
|
P11EA00 |
Bank 1 Air-Fuel Ratio Imbalance (Port) |
Comes on |
DTC stored |
SAE Code: P11EA |
|
P11EC00 |
Cylinder #1 Air-Fuel Ratio Imbalance (Port) |
Comes on |
DTC stored |
SAE Code: P11EC |
|
P11ED00 |
Cylinder #2 Air-Fuel Ratio Imbalance (Port) |
Comes on |
DTC stored |
SAE Code: P11ED |
|
P11EE00 |
Cylinder #3 Air-Fuel Ratio Imbalance (Port) |
Comes on |
DTC stored |
SAE Code: P11EE |
|
P11EF00 |
Cylinder #4 Air-Fuel Ratio Imbalance (Port) |
Comes on |
DTC stored |
SAE Code: P11EF |
|
P123513 |
High Pressure Fuel Pump Circuit Open |
Comes on |
DTC stored |
SAE Code: P1235 |
|
P12D013 |
Fuel Pump Control (All Phase) Circuit Open |
Comes on |
DTC stored |
SAE Code: P12D0 |
|
P12D113 |
Fuel Pump Control (U Phase) Circuit Open |
Comes on |
DTC stored |
SAE Code: P12D1 |
|
P12D213 |
Fuel Pump Control (V Phase) Circuit Open |
Comes on |
DTC stored |
SAE Code: P12D2 |
|
P12D313 |
Fuel Pump Control (W Phase) Circuit Open |
Comes on |
DTC stored |
SAE Code: P12D3 |
|
P12D41D |
Fuel Pump Control Circuit Current Out of Range |
Comes on |
DTC stored |
SAE Code: P12D4 |
|
P12D501 |
Fuel Pump Control General Electrical Failure |
Comes on |
DTC stored |
SAE Code: P12D5 |
|
P136001 |
"A" Camshaft Position Actuator Bank 1 General Electrical Failure |
Comes on |
DTC stored |
SAE Code: P1360 |
|
P136201 |
"B" Camshaft Position Actuator Bank 1 General Electrical Failure |
Comes on |
DTC stored |
SAE Code: P1362 |
|
P136411 |
"C" Camshaft Position Actuator Bank 1 Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P1364 |
|
P136415 |
"C" Camshaft Position Actuator Bank 1 Circuit Short to Battery or Open |
Comes on |
DTC stored |
SAE Code: P1364 |
|
P136629 |
"E" Camshaft Position Actuator Bank 1 Signal Invalid |
Comes on |
DTC stored |
SAE Code: P1366 |
|
P140018 |
Exhaust Gas Recirculation "A" Control Circuit 2 Circuit Current Below Threshold |
Comes on |
DTC stored |
SAE Code: P0489 |
|
P140019 |
Exhaust Gas Recirculation "A" Control Circuit 2 Circuit Current Above Threshold |
Comes on |
DTC stored |
SAE Code: P0490 |
|
P142000 |
Evaporative Emission Canister (Small Leak) |
Comes on |
DTC stored |
SAE Code: P1420 |
|
P142100 |
Evaporative Emission Canister (Gross Leak) |
Comes on |
DTC stored |
SAE Code: P1421 |
|
P142200 |
Evaporative Emission Fuel Tank (Small Leak) |
Comes on |
DTC stored |
SAE Code: P1422 |
|
P142300 |
Evaporative Emission Fuel Tank (Gross Leak) |
Comes on |
DTC stored |
SAE Code: P1423 |
|
P145011 |
Fuel Tank Pressure Sensor Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P1452 |
|
P145015 |
Fuel Tank Pressure Sensor Circuit Short to Battery or Open |
Comes on |
DTC stored |
SAE Code: P1453 |
|
P14502A |
Fuel Tank Pressure Sensor Signal Stuck in Range |
Comes on |
DTC stored |
SAE Code: P1451 |
|
P14502F |
Fuel Tank Pressure Sensor Signal Erratic |
Comes on |
DTC stored |
SAE Code: P1451 |
|
P15F009 |
Engine Oil Pressure Too Low (Moderate) |
Does not come on |
DTC stored |
SAE Code: P15F0 |
|
P15F077 |
Engine Oil Pressure Too Low (Minor) |
Does not come on |
DTC stored |
SAE Code: P15F0 |
|
P15F109 |
Variable Oil Pump Component Failure |
Does not come on |
DTC stored |
SAE Code: P15F1 |
|
P15F177 |
Variable Oil Pump Commanded Position Not Reachable |
Does not come on |
DTC stored |
SAE Code: P15F1 |
|
P16B09F |
Actuator Cut Circuit Stuck Off |
Comes on |
DTC stored |
SAE Code: P16B0 |
|
P210014 |
Throttle Actuator "A" Control Motor Circuit Short to Ground or Open |
Comes on |
DTC stored |
SAE Code: P2102 |
|
P210015 |
Throttle Actuator "A" Control Motor Circuit Short to Battery or Open |
Comes on |
DTC stored |
SAE Code: P2103 |
|
P210900 |
Throttle/Pedal Position Sensor "A" Minimum Stop Performance |
Does not come on |
DTC stored |
SAE Code: P2109 |
|
P211172 |
Throttle Actuator "A" Control System Actuator Stuck Open |
Comes on |
DTC stored |
SAE Code: P2111 |
|
P211173 |
Throttle Actuator "A" Control System Actuator Stuck Closed |
Comes on |
DTC stored |
SAE Code: P2112 |
|
P211900 |
Throttle Actuator "A" Control Throttle Body Range/Performance |
Comes on |
DTC stored |
SAE Code: P2119 |
|
P211904 |
Throttle Actuator "A" Control Throttle Body Range/Performance System Internal Failure |
Comes on |
DTC stored |
SAE Code: P2119 |
|
P211977 |
Throttle Actuator "A" Control Throttle Body Range/Performance Commanded Position Not Reachable |
Comes on |
DTC stored |
SAE Code: P2119 |
|
P21199B |
Throttle Actuator "A" Control Throttle Body High/Excessive Flow |
Comes on |
DTC stored |
SAE Code: P2119 |
|
P21352B |
Throttle/Pedal Position Sensor/Switch "A"/"B" Voltage Correlation Signal Cross Coupled |
Comes on |
DTC stored |
SAE Code: P2135 |
|
P219519 |
A/F (O2) Sensor Signal Biased/Stuck Lean Bank 1 Sensor 1 Circuit Current Above Threshold |
Comes on |
DTC stored |
SAE Code: P2195 |
|
P219524 |
A/F (O2) Sensor Signal Biased/Stuck Lean Bank 1 Sensor 1 Signal Stuck High |
Comes on |
DTC stored |
SAE Code: P2195 |
|
P219618 |
A/F (O2) Sensor Signal Biased/Stuck Rich Bank 1 Sensor 1 Circuit Current Below Threshold |
Comes on |
DTC stored |
SAE Code: P2196 |
|
P219623 |
A/F (O2) Sensor Signal Biased/Stuck Rich Bank 1 Sensor 1 Signal Stuck Low |
Comes on |
DTC stored |
SAE Code: P2196 |
|
P219A00 |
Bank 1 Air-Fuel Ratio Imbalance |
Comes on |
DTC stored |
SAE Code: P219A |
|
P219C00 |
Cylinder 1 Air-Fuel Ratio Imbalance |
Comes on |
DTC stored |
SAE Code: P219C |
|
P219D00 |
Cylinder 2 Air-Fuel Ratio Imbalance |
Comes on |
DTC stored |
SAE Code: P219D |
|
P219E00 |
Cylinder 3 Air-Fuel Ratio Imbalance |
Comes on |
DTC stored |
SAE Code: P219E |
|
P219F00 |
Cylinder 4 Air-Fuel Ratio Imbalance |
Comes on |
DTC stored |
SAE Code: P219F |
|
P21CF13 |
Cylinder 1 Injector "B" Circuit Open |
Comes on |
DTC stored |
SAE Code: P21CF |
|
P21D013 |
Cylinder 2 Injector "B" Circuit Open |
Comes on |
DTC stored |
SAE Code: P21D0 |
|
P21D113 |
Cylinder 3 Injector "B" Circuit Open |
Comes on |
DTC stored |
SAE Code: P21D1 |
|
P21D213 |
Cylinder 4 Injector "B" Circuit Open |
Comes on |
DTC stored |
SAE Code: P21D2 |
|
P222611 |
Barometric Pressure Sensor "A" Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P2228 |
|
P222615 |
Barometric Pressure Sensor "A" Circuit Short to Battery or Open |
Comes on |
DTC stored |
SAE Code: P2229 |
|
P223711 |
A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P2238 |
|
P223712 |
A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Short to Battery |
Comes on |
DTC stored |
SAE Code: P2239 |
|
P223713 |
A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Open |
Comes on |
DTC stored |
SAE Code: P2237 |
|
P223716 |
A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Voltage Below Threshold |
Comes on |
DTC stored |
SAE Code: P2238 |
|
P223717 |
A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Voltage Above Threshold |
Comes on |
DTC stored |
SAE Code: P2239 |
|
P22371B |
A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Resistance Above Threshold |
Comes on |
DTC stored |
SAE Code: P2238 |
|
P225111 |
O2 Sensor Negative Current Control Bank 1 Sensor 1 Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P2252 |
|
P225112 |
O2 Sensor Negative Current Control Bank 1 Sensor 1 Circuit Short to Battery |
Comes on |
DTC stored |
SAE Code: P2253 |
|
P227019 |
A/F (O2) Sensor Signal Biased/Stuck Lean Bank 1 Sensor 2 Circuit Current Above Threshold |
Comes on |
DTC stored |
SAE Code: P2270 |
|
P227118 |
A/F (O2) Sensor Signal Biased/Stuck Rich Bank 1 Sensor 2 Circuit Current Below Threshold |
Comes on |
DTC stored |
SAE Code: P2271 |
|
P22AB11 |
A/F (O2) Sensor Positive Current Control Bank 1 Sensor 2 Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P22AC |
|
P22AB12 |
A/F (O2) Sensor Positive Current Control Bank 1 Sensor 2 Circuit Short to Battery |
Comes on |
DTC stored |
SAE Code: P22AD |
|
P22AB13 |
A/F (O2) Sensor Positive Current Control Bank 1 Sensor 2 Circuit Open |
Comes on |
DTC stored |
SAE Code: P22AB |
|
P22AB16 |
A/F (O2) Sensor Positive Current Control Bank 1 Sensor 2 Circuit Voltage Below Threshold |
Comes on |
DTC stored |
SAE Code: P22AC |
|
P22AB17 |
A/F (O2) Sensor Positive Current Control Bank 1 Sensor 2 Circuit Voltage Above Threshold |
Comes on |
DTC stored |
SAE Code: P22AD |
|
P22B211 |
A/F (O2) Sensor Negative Current Control Bank 1 Sensor 2 Circuit Short to Ground |
Comes on |
DTC stored |
SAE Code: P22B3 |
|
P22B212 |
A/F (O2) Sensor Negative Current Control Bank 1 Sensor 2 Circuit Short to Battery |
Comes on |
DTC stored |
SAE Code: P22B4 |
|
P24007E |
Evaporative Emission System Leak Detection Pump Control Circuit Actuator Stuck On |
Comes on |
DTC stored |
SAE Code: P2402 |
|
P24007F |
Evaporative Emission System Leak Detection Pump Control Circuit Actuator Stuck Off |
Comes on |
DTC stored |
SAE Code: P2401 |
|
P24187E |
Evaporative Emission System Switching Valve Control Circuit Actuator Stuck On |
Comes on |
DTC stored |
SAE Code: P2419 |
|
P24187F |
Evaporative Emission System Switching Valve Control Circuit Actuator Stuck Off |
Comes on |
DTC stored |
SAE Code: P2420 |
|
P24507E |
Evaporative Emission System Switching Valve Actuator Stuck On |
Comes on |
DTC stored |
SAE Code: P2450 |
|
P24517F |
Evaporative Emission System Switching Valve Actuator Stuck Off |
Comes on |
DTC stored |
SAE Code: P2451 |
|
P261029 |
ECM/PCM Engine Off Timer Performance Signal Invalid |
Comes on |
DTC stored |
SAE Code: P2610 |
|
P261093 |
ECM/PCM Engine Off Timer Performance No Operation |
Comes on |
DTC stored |
SAE Code: P2610 |
|
P261401 |
Camshaft Position Signal Output "A" General Electrical Failure |
Comes on |
DTC stored |
SAE Code: P2614 |
|
P268111 |
Engine Coolant Bypass Valve Circuit Short to Ground |
Does not come on |
DTC stored |
SAE Code: P2682 |
|
P268115 |
Engine Coolant Bypass Valve Circuit Short to Battery or Open |
Does not come on |
DTC stored |
SAE Code: P2683 |
|
P26CA12 |
Engine Coolant Pump Circuit Short to Battery |
Comes on |
DTC stored |
SAE Code: P26CD |
|
P26CA14 |
Engine Coolant Pump Circuit Short to Ground or Open |
Comes on |
DTC stored |
SAE Code: P26CC |
|
P26CA31 |
Engine Coolant Pump No Signal |
Comes on |
DTC stored |
SAE Code: P26CA |
|
P26CB71 |
Engine Coolant Pump Actuator Stuck |
Comes on |
DTC stored |
SAE Code: P26CB |
|
P26CE37 |
Engine Coolant Pump Overspeed |
Does not come on |
DTC stored |
SAE Code: P26CE |
|
P319000 |
Poor Engine Power |
Comes on |
DTC stored |
SAE Code: P3190 |
|
P319100 |
Engine does not Start |
Comes on |
DTC stored |
SAE Code: P3191 |
|
P319300 |
Fuel Run Out |
Does not come on |
DTC stored |
SAE Code: P3193 |
|
U011087 |
Lost Communication with Drive Motor Control Module "A" Missing Message |
Comes on |
DTC stored |
SAE Code: U0110 |
|
U012987 |
Lost Communication with Brake System Control Module Missing Message |
Comes on |
DTC stored |
SAE Code: U0129 |
|
U028487 |
Lost Communication with Active Grille Air Shutter Module "A" Missing Message |
Comes on |
DTC stored |
SAE Code: U0284 |
|
U029387 |
Lost Communication With Hybrid Powertrain Control Module Missing Message |
Comes on |
DTC stored |
SAE Code: U0293 |
|
U129387 |
Lost Communication between Hybrid Powertrain Control Module and Active Grille Air Shutter Missing Message |
Comes on |
DTC stored |
SAE Code: U1293 |
Dtc Check / Clear
DTC CHECK / CLEAR
NOTICE:
When the diagnosis system is changed from normal mode to check mode or vice versa, all DTCs and Freeze Frame Data recorded in normal mode are cleared. Before changing modes, always check and make a note of DTCs and Freeze Frame Data.
HINT:
- DTCs which are stored in the ECM can be displayed on the Techstream. The Techstream can display the confirmed, pending and permanent DTCs.
- If a malfunction is detected during the current driving cycle, confirmed and permanent DTCs are stored.
- Some DTCs are not stored if the ECM does not detect the same malfunction again during a second consecutive driving cycle. However, such malfunctions, detected on only one occasion, are stored as pending DTCs.
- Confirmed and pending DTCs can be cleared by using the Techstream or by disconnecting the cable from the negative (-) auxiliary battery terminal. However, permanent DTCs cannot be cleared using either of these two methods.
- After clearing current DTCs using the Techstream (or by disconnecting the cable from the negative (-) auxiliary battery terminal), permanent DTCs can be cleared when the universal trip is performed and then the system is determined to be normal for the relevant DTCs. The driving pattern to obtain a normal judgment is described under the "Confirmation Driving Pattern" for the respective DTC.
To clear permanent DTCs, all of the following conditions must be are met:
- There is a history that universal trip driving was performed.
- The vehicle has been judged as normal for 2 trips. (Normal judgment does not have to be performed in 2 consecutive trip, but normal judgment should occur in the latest trip.) (not for misfire and fuel system DTCs)
- No malfunctions are detected.
Pending DTC |
Store condition |
Malfunction detected |
Clear condition |
System determined to be normal or DTCs cleared using Techstream or Cable disconnected from negative (-) auxiliary battery terminal |
|
Confirmed DTC |
Store condition |
Malfunction detected (2nd trip) |
Clear condition |
No malfunctions in 40 driving cycles or DTCs cleared using Techstream or Cable disconnected from negative (-) auxiliary battery terminal |
|
Permanent DTC |
Store condition |
Malfunction detected (2nd trip) |
Clear condition |
Power switch turned to on (IG) after normal judgment obtained in 3 consecutive driving cycles or After DTCs cleared using Techstream or cable disconnected from negative (-) auxiliary battery terminal, universal trip performed and normal judgment obtained for 2 trips (not for misfire and fuel system DTCs) or After DTCs cleared using Techstream or cable disconnected from negative (-) auxiliary battery terminal, malfunction not detected when universal trip driving performed (misfire and fuel system DTCs) |
|
MIL |
ON |
Malfunction detected (2nd trip) |
OFF |
Power switch turned to on (IG) after normal judgment obtained in 3 consecutive driving cycles or DTCs cleared using Techstream or Cable disconnected from negative (-) auxiliary battery terminal |
HINT:
- Obtaining a normal judgment and performing a universal trip driving pattern can be done in the same driving cycle or in different driving cycles.
- It is unnecessary to obtain a normal judgment if the output DTCs are misfire or fuel system DTCs.
CHECK DTC
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine / Trouble Codes.
Powertrain > Engine > Trouble Codes(e) Check the DTC(s) and Freeze Frame Data, and then write them down.
Techstream Display | Description |
|---|---|
Test Failed |
Shows the malfunction judgment results during the current trip. |
Pending |
Shows the malfunction judgment results up to now. (Indicates the possibility of a malfunction when no DTC is confirmed.) |
Confirmed |
Shows the DTCs confirmed up to now. (The number of current trips differs for each DTC.) |
(f) Check the details of the DTC(s).
Click here ![]()
CHECK TIME STAMP
HINT:
By checking Time Stamp, the time and order in which DTCs were stored in an ECU can be checked.
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Health Check.
(e) Perform the following steps when the data setting screen is displayed.
(f) Select the systems for which to perform Health Check and check for time stamp data.
Selectable items:- Powertrain
- Chassis
- Body
- Store All Data
(g) Select "Yes" when "Do you want to store time stamp data?" is displayed.
HINT:
If "Yes" is not selected, time stamp data will not be stored.
(h) After Health Check has completed, select "Time Stamp Data" to display the Time Stamp screen.
(i) Select the desired system from the drop-down list on the bottom of the Time Stamp screen.
(j) Check the order and time which DTCs were stored for the selected system.
CLEAR DTC (Pending and Confirmed DTC)
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine / Trouble Codes.
(e) Clear the DTCs.
Powertrain > Engine > Clear DTCsCLEAR DTC (Pending and Confirmed DTC without using Techstream)
(a) Perform either of the following operations:
NOTICE:
After turning power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here ![]()
(1) Disconnect the cable from the negative (-) auxiliary battery terminal for more than 1 minute.
(2) Remove the EFI-MAIN NO. 4 fuse from the No. 1 engine room relay block and No. 1 junction block assembly located inside the engine compartment for more than 1 minute.
OUTLINE- After clearing current DTCs using the Techstream (or by disconnecting the cable from the negative (-) auxiliary battery terminal), permanent DTCs can be cleared when the universal trip is performed and then the system is determined to be normal for the relevant DTCs. The driving pattern to obtain a normal judgment is described under the "Confirmation Driving Pattern" for the respective DTC.
- To clear permanent DTCs, all of the following conditions must be are met:
- There is a history that universal trip driving was performed.
- The vehicle has been judged as normal for 2 trips. (Normal judgment does not have to be performed in 2 consecutive trip, but normal judgment should occur in the latest trip.) (not for misfire and fuel system DTCs)
- No malfunctions are detected.
CLEAR PERMANENT DTC
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine / Trouble Codes.
Powertrain > Engine > Trouble CodesHINT:
If "PERMANENT" in the top right of the screen displays "YES", permanent DTCs are stored.
(e) Select the "Generic" tab.
(f) Check if permanent DTCs are stored.
HINT:
If permanent DTCs are not output, it is not necessary to continue this procedure.
(g) Clear the DTCs.
Powertrain > Engine > Clear DTCsNOTICE:
Do not clear the DTCs or disconnect the cable from the auxiliary battery terminal after performing this step.
(h) Perform the universal trip.
HINT:
The driving pattern to obtain a normal judgment and the universal trip driving can be performed consecutively in the same driving cycle.
- Turn the power switch on (READY) and wait for 30 seconds or more.
- Drive the vehicle at 40 km/h or more for a total of 5 minutes or more.
CAUTION:
When performing a driving pattern, obey all speed limits and traffic laws.
HINT:
It is possible to complete the drive pattern even if the vehicle decelerates to less than 40 km/h during the driving cycle provided that the vehicle is driven at 40 km/h or more for a total of 5 minutes.
- Allow 10 minutes or more to elapse from the time the power switch turned on (READY).
(i) Turn the power switch off and wait for 2 minutes or more.
(j) Turn the power switch on (IG).
(k) Enter the following menus: Powertrain / Engine / Trouble Codes.
Powertrain > Engine > Trouble Codes(l) Check that the permanent DTCs have been cleared.
HINT:
If permanent DTCs are not output, it is not necessary to continue this procedure.
(m) Perform the normal judgment procedure in the respective confirmation driving pattern of each output DTC.
HINT:
- Confirmation driving patterns do not need to be performed for misfire and fuel system DTCs.
- Do not turn the power switch off by mistake during this step.
(n) With the power switch on (READY) wait for 5 seconds or more. (Except when the power switch is already turned on (READY) or the engine is running)
(o) Turn the power switch off and wait for 2 minutes or more.
(p) Turn the power switch on (IG).
(q) Enter the following menus: Powertrain / Engine / Trouble Codes.
Powertrain > Engine > Trouble Codes(r) Check that the permanent DTCs have been cleared.
HINT:
If permanent DTCs are not output, it is not necessary to continue this procedure.
(s) Perform the normal judgment procedure in the respective confirmation driving pattern of each output DTC.
HINT:
- Confirmation driving patterns do not need to be performed for misfire and fuel system DTCs.
- Do not turn the power switch off by mistake during this step.
(t) With the power switch on (READY) wait for 5 seconds or more. (Except when the power switch is already turned on (READY) or the engine is running)
(u) Turn the power switch off and wait for 2 minutes or more.
(v) Turn the power switch on (IG).
(w) Enter the following menus: Powertrain / Engine / Trouble Codes.
Powertrain > Engine > Trouble Codes(x) Check that the permanent DTCs have been cleared.
