Air Fuel Ratio Sensor
Components
COMPONENTS
ILLUSTRATION
*1 |
V-BANK COVER SUB-ASSEMBLY |
*2 |
AIR FUEL RATIO SENSOR (for Bank 1) |
*3 |
AIR FUEL RATIO SENSOR (for Bank 2) |
- |
- |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
* |
For use with SST |
Inspection
INSPECTION
PROCEDURE
1. INSPECT AIR FUEL RATIO SENSOR (for Bank 1)
(a) Measure the resistance according to the value(s) in the table below. Standard Resistance:
If the result is not as specified, replace the air fuel ratio sensor. |
|
2. INSPECT AIR FUEL RATIO SENSOR (for Bank 2)
(a) Measure the resistance according to the value(s) in the table below. Standard Resistance:
If the result is not as specified, replace the air fuel ratio sensor. |
|
Installation
INSTALLATION
PROCEDURE
1. INSTALL AIR FUEL RATIO SENSOR (for Bank 1)
HINT:
Perform "Inspection After Repair" after replacing the air fuel ratio sensor.
Click here ![]()
(a) Using SST, install the air fuel ratio sensor to the exhaust manifold assembly RH (TWC: Front Catalyst). SST: 09224-00012 Torque: Specified tightening torque : 44 N·m {449 kgf·cm, 32 ft·lbf} NOTICE: If the air fuel ratio sensor has been struck or dropped, replace it. HINT:
|
|
(b) Engage the 2 wire harness clamps.
(c) Connect the air fuel ratio sensor connector.
2. INSTALL AIR FUEL RATIO SENSOR (for Bank 2)
HINT:
Perform "Inspection After Repair" after replacing the air fuel ratio sensor.
Click here ![]()
(a) Using SST, install the air fuel ratio sensor to the exhaust manifold assembly LH (TWC: Front Catalyst). SST: 09224-00012 Torque: Specified tightening torque : 44 N·m {449 kgf·cm, 32 ft·lbf} NOTICE: If the air fuel ratio sensor has been struck or dropped, replace it. HINT:
|
|
(b) Connect the air fuel ratio sensor connector.
(c) Engage the wire harness clamp.
3. INSTALL V-BANK COVER SUB-ASSEMBLY
Click here ![]()
4. INSPECT FOR EXHAUST GAS LEAK
Click here ![]()
5. PERFORM INITIALIZATION
(a) Perform "Inspection After Repair" after replacing an air fuel ratio sensor.
Click here ![]()
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during air fuel ratio sensor removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/ReplacedReplaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
|
Inspection after repair |
|
PROCEDURE
1. REMOVE V-BANK COVER SUB-ASSEMBLY
Click here ![]()
2. REMOVE AIR FUEL RATIO SENSOR (for Bank 2)
(a) Disengage the wire harness clamp. |
![]() |
(b) Disconnect the air fuel ratio sensor connector.
(c) Using SST, remove the air fuel ratio sensor from the exhaust manifold assembly LH (TWC: Front Catalyst). SST: 09224-00012 NOTICE: If the air fuel ratio sensor has been struck or dropped, replace it. |
![]() |
3. REMOVE AIR FUEL RATIO SENSOR (for Bank 1)
(a) Disconnect the air fuel ratio sensor connector. |
![]() |
(b) Disengage the 2 wire harness clamps.
(c) Using SST, remove the air fuel ratio sensor from the exhaust manifold assembly RH (TWC: Front Catalyst). SST: 09224-00012 NOTICE: If the air fuel ratio sensor has been struck or dropped, replace it. |
![]() |









