Egr Cooler
Components
COMPONENTS
ILLUSTRATION
*1 |
EGR COOLER ASSEMBLY |
*2 |
EGR VALVE GASKET |
*3 |
EGR COOLER GASKET |
*4 |
NO. 4 WATER BY-PASS HOSE |
*5 |
NO. 3 WATER BY-PASS HOSE |
- |
- |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
Installation
INSTALLATION
PROCEDURE
1. INSTALL EGR COOLER ASSEMBLY
(a) Install a new EGR cooler gasket to the EGR cooler assembly. NOTICE: Make sure that the claws of the EGR cooler gasket are toward the EGR cooler assembly side. |
|
(b) Install a new EGR valve gasket to the EGR valve assembly. NOTICE: Make sure that the claws of the EGR valve gasket are toward the EGR valve assembly side. |
|
(c) Temporarily install the EGR cooler assembly to the cylinder head sub-assembly and EGR valve assembly with the 5 bolts. |
![]() |
(d) Tighten the 3 bolts (A).
Torque:
21 N·m {214 kgf·cm, 15 ft·lbf}
(e) Tighten the 2 bolts (B).
Torque:
21 N·m {214 kgf·cm, 15 ft·lbf}
(f) Connect the No. 3 water by-pass hose and No. 4 water by-pass hose to the EGR cooler assembly and slide the 2 clips to secure them.
2. INSTALL INVERTER WITH CONVERTER ASSEMBLY
Click here ![]()
3. ADD ENGINE COOLANT (for Engine)
Click here ![]()
4. INSPECT FOR COOLANT LEAK (for Engine)
Click here ![]()
5. INSPECT FOR EXHAUST GAS LEAK
Click here ![]()
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during EGR cooler assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/ReplacedReplaced Part or Performed Procedure | Necessary Procedures | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
| *1: When performing learning using the Techstream. Click here |
|||
Auxiliary battery terminal is disconnected/reconnected |
Perform steering sensor zero point calibration |
Lane departure alert system (w/ Steering Control) |
|
Pre-collision system |
|||
Intelligent clearance sonar system* |
|||
Lighting System (for HV Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking assist monitor system |
||
Panoramic view monitor system |
|||
Replacement of inverter with converter assembly |
Resolver learning |
|
|
Replacement of ECM |
Perform Vehicle Identification Number (VIN) registration |
MIL comes on |
|
Gas leak from exhaust system is repaired |
Inspection After Repair |
|
|
PROCEDURE
1. DRAIN ENGINE COOLANT (for Engine)
Click here ![]()
2. REMOVE INVERTER WITH CONVERTER ASSEMBLY
Click here ![]()
3. REMOVE EGR COOLER ASSEMBLY
(a) Slide the 2 clips and disconnect the No. 3 water by-pass hose and No. 4 water by-pass hose from the EGR cooler assembly. |
|
(b) Remove the 5 bolts and EGR cooler assembly from the cylinder head sub-assembly and EGR valve assembly. |
![]() |
(c) Remove the EGR valve gasket from the EGR valve assembly. |
![]() |
(d) Remove the EGR cooler gasket from the EGR cooler assembly. |
![]() |








