Problem Symptoms Table. Readiness Monitor Drive Pattern. Registration
Problem Symptoms Table
PROBLEM SYMPTOMS TABLE
HINT:
- Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
- Inspect the fuses and relays related to this system before inspecting the suspected areas below.
Symptom | Suspected Area | Link |
|---|---|---|
Engine does not crank (Does not start) |
Hybrid control system |
|
VC output circuit (ECM 5 V output) |
||
No initial combustion (Does not start) |
ECM power source circuit |
|
VC output circuit (ECM 5 V output) |
||
Ignition system |
||
Fuel system |
||
Port fuel injector assembly |
||
Direct fuel injector assembly |
||
Fuel pump (for low pressure side) |
||
Crankshaft position sensor |
||
Intake system |
||
Valve timing |
||
EGR valve assembly |
||
Engine cranks normally but difficult to start |
ECM power source circuit |
|
Throttle body with motor assembly |
||
Fuel pump assembly (for high pressure side) |
||
Fuel pump (for low pressure side) |
||
Engine coolant temperature sensor |
||
Fuel system |
||
Ignition system |
||
Compression |
||
Port fuel injector assembly |
||
Direct fuel injector assembly |
||
Crankshaft position sensor |
||
Intake system |
||
Valve timing |
||
EGR valve assembly |
||
Incomplete intermittent combustion occurs (Does not start) |
Fuel system |
|
Fuel pump (for low pressure side) |
||
Ignition system |
||
Port fuel injector assembly |
||
Direct fuel injector assembly |
||
Crankshaft position sensor |
||
Intake system |
||
Valve timing |
||
High engine speed |
Throttle body with motor assembly |
|
ECM power source circuit |
||
PCV system |
||
Low engine speed (Poor idle) |
Fuel system |
|
Throttle body with motor assembly |
||
Port fuel injector assembly |
||
Direct fuel injector assembly |
||
Fuel pump assembly (for high pressure side) |
||
PCV system |
||
Intake system |
||
Rough idle |
Flow chart [Rough idling] |
|
Throttle body with motor assembly |
||
Port fuel injector assembly |
||
Direct fuel injector assembly |
||
Fuel pump assembly (for high pressure side) |
||
Ignition system |
||
Air fuel ratio sensor (sensor 1) |
||
Air fuel ratio sensor (sensor 2) |
||
Mass air flow meter sub-assembly |
||
Manifold absolute pressure sensor |
||
Compression |
||
Fuel system |
||
Intake system |
||
Valve timing |
||
EGR valve assembly |
||
Hunting (Poor idle) |
Throttle body with motor assembly |
|
ECM power source circuit |
||
Fuel system |
||
Spark plug |
||
Intake system |
||
Drive start control |
||
Hesitation/Poor acceleration (Poor driveability) |
Port fuel injector assembly |
|
Direct fuel injector assembly |
||
Fuel system |
||
Fuel pump assembly (for high pressure side) |
||
Ignition system |
||
Intake system |
||
Valve timing |
||
Brake override system |
||
Drive start control |
||
Surging (Poor driveability) |
Fuel system |
|
Fuel pump (for low pressure side) |
||
Ignition system |
||
Port fuel injector assembly |
||
Direct fuel injector assembly |
||
Engine stalls soon after starting |
Fuel system |
|
Throttle body with motor assembly |
||
Crankshaft position sensor |
||
Ignition system |
||
Fuel pump assembly (for high pressure side) |
||
Intake system |
||
Valve timing |
||
EGR valve assembly |
||
MIL (Malfunction Indicator Lamp) malfunction |
MIL Circuit |
|
Meter/Gauge system |
||
Unable/difficult to refuel |
Fuel system (canister, refueling valve, roll over valve, fuel tank, etc.) |
- |
Readiness Monitor Drive Pattern
READINESS MONITOR DRIVE PATTERN
PURPOSE OF READINESS TESTS
- The On-Board Diagnostic (OBD II) system is designed to monitor the performance of emission related components, and indicate any detected abnormalities using DTCs (Diagnostic Trouble Codes). Since various components need to be monitored during different driving conditions, the OBD II system is designed to run separate monitoring programs called Readiness Monitors.
- To view the status, enter the following menus: Powertrain / Engine / Monitor / Current Monitor / Current.
- When the status of a Readiness Monitor reads Complete, the necessary conditions have been met for running the performance tests for that Readiness Monitor.
- A generic OBD II scan tool can also be used to view the Readiness Monitor status.
HINT:
Many state Inspection and Maintenance (I/M) programs require the status of vehicle Readiness Monitor to show Complete before beginning emission tests.
- The Readiness Monitor is reset to Incomplete if:
- The ECM has lost auxiliary battery power or blown a fuse.
- DTCs have been cleared.
- The conditions for running the Readiness Monitor have not been met.
- If the Readiness Monitor status shows Incomplete, follow the appropriate Readiness Monitor Drive Pattern to change the status to Complete.
CAUTION:
Strictly observe posted speed limits, traffic laws, and road conditions when performing these drive patterns.
NOTICE:
These drive patterns represent the fastest method of satisfying all conditions necessary to achieve complete status for each specific Readiness Monitor.
In the event of a drive pattern being interrupted (possibly due to factors such as traffic conditions), the drive pattern can be resumed. In most cases, the Readiness Monitor will still achieve complete status upon completion of the drive pattern.
To ensure completion of the Readiness Monitors, avoid sudden changes in vehicle load and speed (driving up and down hills and/or sudden acceleration).
VVT SYSTEM MONITOR
(a) Refer to Confirmation Driving Pattern [P001100].
Click here ![]()
(b) Refer to Confirmation Driving Pattern [P001200].
Click here ![]()
(c) Refer to Confirmation Driving Pattern [P001400].
Click here ![]()
CATALYST MONITOR (ACTIVE AIR FUEL RATIO CONTROL TYPE)
(a) Refer to Confirmation Driving Pattern [P042000].
Click here ![]()
EVAP SYSTEM MONITOR (KEY OFF TYPE)
(a) Refer to Confirmation Driving Pattern [EVAP System].
Click here ![]()
AIR FUEL RATIO (A/F) SENSOR MONITORS (ACTIVE AIR FUEL RATIO CONTROL TYPE)
(a) Refer to Confirmation Driving Pattern [P00D562].
Click here ![]()
(b) Refer to Confirmation Driving Pattern [P013616].
Click here ![]()
(c) Refer to Confirmation Driving Pattern [P014C00].
Click here ![]()
(d) Refer to Confirmation Driving Pattern [P219519].
Click here ![]()
(e) Refer to Confirmation Driving Pattern [P227019].
Click here ![]()
AIR FUEL RATIO (A/F) IMBALANCE MONITOR
(a) Refer to Confirmation Driving Pattern [P11EA00].
Click here ![]()
EGR SYSTEM MONITOR
(a) Refer to Confirmation Driving Pattern [P04019C].
Click here ![]()
Registration
REGISTRATION
PROCEDURE
1. VIN (VEHICLE IDENTIFICATION NUMBER)
NOTICE:
The Vehicle Identification Number (VIN) must be written to a replacement ECM.
HINT:
The VIN is a 17-digit alphanumeric vehicle identification number. The Techstream is required to register the VIN.
(a) DESCRIPTION
HINT:
This registration section consists of 2 parts: Read VIN and Write VIN.
(1) Read VIN: This procedure allows the VIN stored in the ECM to be read in order to confirm that the 2 VINs, provided with the vehicle and stored in the vehicle ECM, are the same.
(2) Write VIN: This procedure allows the VIN to be written into the ECM. If the ECM is replaced, or the ECM VIN and vehicle VIN do not match, the VIN can be registered, or overwritten in the ECM by following this procedure.
(b) READ VIN
(1) Confirm the vehicle VIN.
(2) Connect the Techstream to the DLC3.
(3) Turn the power switch on (IG).
(4) Turn the Techstream on.
(5) Enter the following menus: Powertrain / Engine / Utility / VIN / VIN Read.
Powertrain > Engine > UtilityVIN
(6) According to the display on the Techstream, read the VIN stored in the ECM.
(c) WRITE VIN
(1) Confirm the vehicle VIN.
(2) Connect the Techstream to the DLC3.
(3) Turn the power switch on (IG).
(4) Turn the Techstream on.
(5) Enter the following menus: Powertrain / Engine / Utility / VIN / VIN Write.
Powertrain > Engine > UtilityVIN
(6) According to the display on the Techstream, write the VIN to the ECM.
