Camshaft
Components
COMPONENTS
ILLUSTRATION
*1 |
VENTILATION HOSE |
*2 |
PURGE VALVE (PURGE VSV) |
*3 |
NO. 1 FUEL VAPOR FEED HOSE |
*4 |
NO. 2 SURGE TANK STAY |
*5 |
INTAKE AIR SURGE TANK ASSEMBLY |
*6 |
AIR SURGE TANK TO INTAKE MANIFOLD GASKET |
*7 |
VACUUM HOSE SUB-ASSEMBLY |
*8 |
VACUUM HOSE |
*9 |
NO. 2 AIR TUBE |
- |
- |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
![]() |
Do not apply lubricants (to the threaded parts) |
- |
- |
ILLUSTRATION
*1 |
WATER FILLER BRACKET |
*2 |
WIRE HARNESS CLAMP BRACKET |
*3 |
VACUUM PUMP ASSEMBLY |
*4 |
IGNITION COIL ASSEMBLY |
*5 |
ENGINE OIL LEVEL DIPSTICK GUIDE |
*6 |
ENGINE OIL LEVEL DIPSTICK |
*7 |
ENGINE OIL LEVEL DIPSTICK GUIDE O-RING |
*8 |
NO. 2 O-RING |
*9 |
NO. 3 O-RING |
- |
- |
![]() |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
- |
- |
ILLUSTRATION
*1 |
CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 1) |
*2 |
CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 1) |
*3 |
VVT SENSOR (for Intake Side of Bank 1) |
*4 |
VVT SENSOR (for Exhaust Side of Bank 1) |
*5 |
CYLINDER HEAD COVER SUB-ASSEMBLY |
*6 |
CYLINDER HEAD COVER GASKET |
*7 |
SPARK PLUG TUBE GASKET |
*8 |
NO. 1 ENGINE COVER SUB-ASSEMBLY |
*9 |
O-RING |
- |
- |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
![]() |
Adhesive 1324 |
★ |
Precoated part |
ILLUSTRATION
*1 |
CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 2) |
*2 |
CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 2) |
*3 |
VVT SENSOR (for Intake Side of Bank 2) |
*4 |
VVT SENSOR (for Exhaust Side of Bank 2) |
*5 |
CYLINDER HEAD COVER SUB-ASSEMBLY LH |
*6 |
NO. 2 CYLINDER HEAD COVER GASKET |
*7 |
SPARK PLUG TUBE GASKET |
*8 |
O-RING |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
![]() |
Adhesive 1324 |
★ |
Precoated part |
ILLUSTRATION
*1 |
CAMSHAFT |
*2 |
NO. 2 CAMSHAFT |
*3 |
CAMSHAFT BEARING CAP (for Bank 1) |
*4 |
NO. 2 CHAIN TENSIONER ASSEMBLY |
*5 |
CAMSHAFT TIMING GEAR ASSEMBLY (for Bank 1) |
*6 |
CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY (for Bank 1) |
*7 |
CAMSHAFT TIMING GEAR BOLT (for Intake Side of Bank 1) |
*8 |
NO. 2 CHAIN SUB-ASSEMBLY (for Bank 1) |
*9 |
FUEL PUMP LIFTER HOUSING |
*10 |
CAMSHAFT BEARING CAP OIL HOLE GASKET |
*11 |
CHAIN SUB-ASSEMBLY (for Bank 1) |
*12 |
NO. 1 CHAIN TENSIONER ASSEMBLY |
*13 |
TIMING CHAIN COVER GASKET |
*14 |
TIMING CHAIN COVER PLATE |
*15 |
CAMSHAFT TIMING GEAR BOLT (for Exhaust Side of Bank 1) |
*16 |
NO. 1 CAMSHAFT BEARING CAP |
*17 |
NO. 2 CAMSHAFT BEARING CAP |
- |
- |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
ILLUSTRATION
*1 |
NO. 3 CAMSHAFT SUB-ASSEMBLY |
*2 |
NO. 4 CAMSHAFT SUB-ASSEMBLY |
*3 |
CAMSHAFT BEARING CAP (for Bank 2) |
*4 |
NO. 3 CHAIN TENSIONER ASSEMBLY |
*5 |
CAMSHAFT TIMING GEAR ASSEMBLY (for Bank 2) |
*6 |
CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY (for Bank 2) |
*7 |
CAMSHAFT TIMING GEAR BOLT (for Intake Side of Bank 2) |
*8 |
NO. 2 CHAIN SUB-ASSEMBLY (for Bank 2) |
*9 |
CAMSHAFT BEARING CAP OIL HOLE GASKET LH |
*10 |
CHAIN SUB-ASSEMBLY (for Bank 2) |
*11 |
CAMSHAFT TIMING GEAR BOLT (for Exhaust Side of Bank 2) |
*12 |
NO. 3 CAMSHAFT BEARING CAP |
*13 |
NO. 4 CAMSHAFT BEARING CAP |
- |
- |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
Installation
INSTALLATION
PROCEDURE
1. SET NO. 1 CYLINDER TO TDC (COMPRESSION)
(a) Confirm that the timing mark (cutout) on the crankshaft pulley is aligned with the "0" timing mark of the timing chain cover assembly. |
|
2. SET CAMSHAFT TIMING GEAR ASSEMBLY (for Bank 2)
HINT:
Perform Inspection After Repair after replacing the camshaft timing gear assembly.
Click here ![]()
(a) Align the mark plate (yellow) with the timing mark of the camshaft timing gear assembly as shown in the illustration and install the No. 2 chain sub-assembly to the camshaft timing gear assembly. |
|
(b) Install the chain sub-assembly to the camshaft timing gear assembly, and then set the camshaft timing gear assembly to the camshaft housing sub-assembly LH. HINT:
|
|
3. SET CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY (for Bank 2)
HINT:
Perform Inspection After Repair after replacing the camshaft timing exhaust gear assembly.
Click here ![]()
(a) Align the mark plate (yellow) with the timing mark of the camshaft timing exhaust gear assembly as shown in the illustration and install the No. 2 chain sub-assembly to the camshaft timing exhaust gear assembly. |
|
(b) Set the camshaft timing exhaust gear assembly to the camshaft housing sub-assembly LH.
4. SET NO. 3 CHAIN TENSIONER ASSEMBLY
(a) While lifting up the camshaft timing exhaust gear assembly, pass the No. 3 chain tensioner assembly through the No. 2 chain sub-assembly and set it in place. NOTICE: Temporarily set the No. 3 chain tensioner assembly only, do not install the bolt. |
![]() |
5. INSTALL NO. 3 CAMSHAFT SUB-ASSEMBLY
HINT:
Perform Inspection After Repair after replacing the No. 3 camshaft sub-assembly.
Click here ![]()
(a) Clean the camshaft housing sub-assembly LH and No. 3 camshaft sub-assembly journals and apply engine oil to them.
(b) Make sure that the No. 1 valve rocker arm sub-assembly is installed as shown in the illustration. |
|
(c) Align the straight pin of the No. 3 camshaft sub-assembly and the pin hole of the camshaft timing gear assembly, and install the No. 3 camshaft sub-assembly to the camshaft timing gear assembly. NOTICE: Be careful not to damage the contact surface of the camshaft timing gear assembly with the straight pin of the No. 3 camshaft sub-assembly. |
|
(d) Check that there is no clearance between the camshaft timing gear assembly and No. 3 camshaft sub-assembly flange.
6. INSTALL NO. 4 CAMSHAFT SUB-ASSEMBLY
HINT:
Perform Inspection After Repair after replacing the No. 4 camshaft sub-assembly.
Click here ![]()
(a) Clean the camshaft housing sub-assembly LH and No. 4 camshaft sub-assembly journals and apply engine oil to them.
(b) Make sure that the No. 1 valve rocker arm sub-assembly is installed as shown in the illustration. |
|
(c) Align the straight pin of the No. 4 camshaft sub-assembly and the pin hole of the camshaft timing exhaust gear assembly, and install the No. 4 camshaft sub-assembly to the camshaft timing exhaust gear assembly. NOTICE: Be careful not to damage the contact surface of the camshaft timing exhaust gear assembly with the straight pin of the No. 4 camshaft sub-assembly. |
|
(d) Check that there is no clearance between the camshaft timing exhaust gear assembly and No. 4 camshaft sub-assembly flange.
7. SET CAMSHAFT BEARING CAP (for Bank 2)
(a) Clean the camshaft bearing caps and apply engine oil to them.
(b) Slide the camshaft timing gear assembly and camshaft timing exhaust gear assembly as shown in the illustration. HINT: To ensure there is sufficient space for installing the No. 3 camshaft bearing cap and No. 4 camshaft bearing cap, slide the camshaft timing gear assembly and camshaft timing exhaust gear assembly. |
![]() |
(c) Remove the replacement bolts and washers (No. 3 camshaft bearing cap and No. 4 camshaft bearing cap side). NOTICE: Do not remove any of the replacement bolts and washers other than those on the No. 3 camshaft bearing cap and No. 4 camshaft bearing cap side. |
|
(d) Temporarily set the No. 3 camshaft bearing cap and No. 4 camshaft bearing cap.
NOTICE:
- Do not install the bolts of the No. 3 camshaft bearing cap and No. 4 camshaft bearing cap.
- Do not install any camshaft bearing caps other than the No. 3 camshaft bearing cap and No. 4 camshaft bearing cap.
(e) Slide the camshaft timing gear assembly and camshaft timing exhaust gear assembly as shown in the illustration. NOTICE: Securely insert the straight pins of the No. 3 camshaft sub-assembly and No. 4 camshaft sub-assembly into the pin holes of the camshaft timing gear assembly and camshaft timing exhaust gear assembly. |
![]() |
8. TEMPORARILY INSTALL CAMSHAFT TIMING GEAR BOLT (for Intake Side of Bank 2)
(a) Check that there is no clearance between the camshaft timing gear assembly and No. 3 camshaft sub-assembly flange.
(b) Apply engine oil to the areas of the camshaft timing gear bolt shown in the illustration. |
![]() |
(c) Use a wrench to hold the hexagonal portion of the No. 3 camshaft sub-assembly.
*a |
Hold |
![]() |
Turn |
(d) Temporarily install the camshaft timing gear bolt to the camshaft timing gear assembly.
Torque:
10 N·m {102 kgf·cm, 7 ft·lbf}
NOTICE:
- Installing the camshaft timing gear bolt while there is external force applied to the camshaft timing gear assembly could result in damage to the engine, so make sure that the camshaft bearing cap is not installed when temporarily installing the camshaft timing gear bolt.
- Be careful not to damage the No. 3 camshaft sub-assembly, camshaft housing sub-assembly LH or spark plug tube with the wrench.
- Make sure that the flange part of the camshaft timing gear bolt is directly contacting the camshaft timing gear assembly.
9. TEMPORARILY INSTALL CAMSHAFT TIMING GEAR BOLT (for Exhaust Side of Bank 2)
(a) Check that there is no clearance between the camshaft timing exhaust gear assembly and No. 4 camshaft sub-assembly flange.
(b) Apply engine oil to the areas of the camshaft timing gear bolt shown in the illustration. |
![]() |
(c) Use a wrench to hold the hexagonal portion of the No. 4 camshaft sub-assembly.
*a |
Hold |
![]() |
Turn |
(d) Temporarily install the camshaft timing gear bolt to the camshaft timing exhaust gear assembly.
Torque:
10 N·m {102 kgf·cm, 7 ft·lbf}
NOTICE:
- Installing the camshaft timing gear bolt while there is external force applied to the camshaft timing exhaust gear assembly could result in damage to the engine, so make sure that the camshaft bearing cap is not installed when temporarily installing the camshaft timing gear bolt.
- Be careful not to damage the No. 4 camshaft sub-assembly, camshaft housing sub-assembly LH or spark plug tube with the wrench.
- Make sure that the flange part of the camshaft timing gear bolt is directly contacting the camshaft timing exhaust gear assembly.
10. INSTALL CAMSHAFT BEARING CAP (for Bank 2)
(a) Clean the camshaft bearing caps and apply engine oil to them.
(b) Check the marks and numbers on the camshaft bearing caps, and then remove the replacement bolts and washers in the order shown in the illustration. Immediately after removing the replacement bolts and washers in the location for a camshaft bearing cap, install the camshaft bearing cap with the bolts in the order shown in the illustration.
Torque:
Bolt (A) :
28 N·m {286 kgf·cm, 21 ft·lbf}
Bolt (B) :
16 N·m {163 kgf·cm, 12 ft·lbf}
NOTICE:
- Be sure to follow the numerical order when performing this procedure.
- Do not drop replacement bolts and washers into the cylinder head LH.
*a |
Replacement Bolt and Washer |
*b |
Replacement Bolt and Washer Removal |
*c |
Part Installation |
![]() |
Bolt (A) |
![]() |
Bolt (B) |
(c) Check the torque of each bolt again.
11. TIGHTEN CAMSHAFT TIMING GEAR BOLT (for Intake Side of Bank 2)
(a) Use a wrench to hold the hexagonal portion of the No. 3 camshaft sub-assembly.
*a |
Hold |
![]() |
Turn |
(b) Tighten the camshaft timing gear bolt.
Torque:
95 N·m {969 kgf·cm, 70 ft·lbf}
NOTICE:
Be careful not to damage the No. 3 camshaft sub-assembly, camshaft housing sub-assembly LH or spark plug tube with the wrench.
12. TIGHTEN CAMSHAFT TIMING GEAR BOLT (for Exhaust Side of Bank 2)
(a) Use a wrench to hold the hexagonal portion of the No. 4 camshaft sub-assembly.
*a |
Hold |
![]() |
Turn |
(b) Tighten the camshaft timing gear bolt.
Torque:
95 N·m {969 kgf·cm, 70 ft·lbf}
NOTICE:
Be careful not to damage the No. 4 camshaft sub-assembly, camshaft housing sub-assembly LH or spark plug tube with the wrench.
13. INSTALL NO. 3 CHAIN TENSIONER ASSEMBLY
(a) Install the No. 3 chain tensioner assembly with the bolt.
Torque:
21 N·m {214 kgf·cm, 15 ft·lbf}
14. CONNECT CHAIN SUB-ASSEMBLY (for Bank 2)
(a) Align the paint marks on the camshaft timing gear assembly and chain sub-assembly and install the chain sub-assembly to the camshaft timing gear assembly. HINT: If the paint marks are not aligned, align them by turning the No. 3 camshaft sub-assembly slightly. |
|
15. SET CAMSHAFT TIMING GEAR ASSEMBLY (for Bank 1)
HINT:
Perform Inspection After Repair after replacing the camshaft timing gear assembly.
Click here ![]()
(a) Align the mark plate (yellow) with the timing mark of the camshaft timing gear assembly as shown in the illustration and install the No. 2 chain sub-assembly to the camshaft timing gear assembly. |
|
(b) Install the chain sub-assembly to the camshaft timing gear assembly, and then set the camshaft timing gear assembly to the camshaft housing sub-assembly. HINT:
|
|
16. SET CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY (for Bank 1)
HINT:
Perform Inspection After Repair after replacing the camshaft timing exhaust gear assembly.
Click here ![]()
(a) Align the mark plate (yellow) with the timing mark of the camshaft timing exhaust gear assembly as shown in the illustration and install the No. 2 chain sub-assembly to the camshaft timing exhaust gear assembly. |
|
(b) Set the camshaft timing exhaust gear assembly to the camshaft housing sub-assembly.
17. SET NO. 2 CHAIN TENSIONER ASSEMBLY
(a) While lifting up the camshaft timing exhaust gear assembly, pass the No. 2 chain tensioner assembly through the No. 2 chain sub-assembly and set it in place. NOTICE: Temporarily set the No. 2 chain tensioner assembly only, do not install the bolt. |
![]() |
18. INSTALL CAMSHAFT
HINT:
Perform Inspection After Repair after replacing the camshaft.
Click here ![]()
(a) Turn the crankshaft clockwise until it is in the position shown in the illustration so that the chain sub-assembly can be installed easily. HINT: When turning the crankshaft, engine oil may spray out of the oil holes. |
|
(b) Clean the camshaft housing sub-assembly and camshaft journals and apply engine oil to them.
(c) Make sure that the No. 1 valve rocker arm sub-assembly is installed as shown in the illustration. |
|
(d) Align the straight pin of the camshaft and the pin hole of the camshaft timing gear assembly, and install the camshaft to the camshaft timing gear assembly. NOTICE: Be careful not to damage the contact surface of the camshaft timing gear assembly with the straight pin of the camshaft. |
|
(e) Check that there is no clearance between the camshaft timing gear assembly and camshaft flange.
19. INSTALL NO. 2 CAMSHAFT
HINT:
Perform Inspection After Repair after replacing the No. 2 camshaft.
Click here ![]()
(a) Clean the camshaft housing sub-assembly and No. 2 camshaft journals and apply engine oil to them.
(b) Make sure that the No. 1 valve rocker arm sub-assembly is installed as shown in the illustration. |
|
(c) Align the straight pin of the No. 2 camshaft and the pin hole of the camshaft timing exhaust gear assembly, and install the No. 2 camshaft to the camshaft timing exhaust gear assembly. NOTICE: Be careful not to damage the contact surface of the camshaft timing exhaust gear assembly with the straight pin of the No. 2 camshaft. |
|
(d) Check that there is no clearance between the camshaft timing gear assembly and No. 2 camshaft flange.
20. SET CAMSHAFT BEARING CAP (for Bank 1)
(a) Clean the camshaft bearing caps and apply engine oil to them.
(b) Slide the camshaft timing gear assembly and camshaft timing exhaust gear assembly as shown in the illustration. HINT: To ensure there is sufficient space for installing the No. 1 camshaft bearing cap and No. 2 camshaft bearing cap, slide the camshaft timing gear assembly and camshaft timing exhaust gear assembly. |
![]() |
(c) Remove the replacement bolts and washers (No. 1 camshaft bearing cap and No. 2 camshaft bearing cap side). NOTICE: Do not remove any of the replacement bolts and washers other than those on the No. 1 camshaft bearing cap and No. 2 camshaft bearing cap side. |
|
(d) Temporarily set the No. 1 camshaft bearing cap and No. 2 camshaft bearing cap.
NOTICE:
- Do not install the bolts of the No. 1 camshaft bearing cap and No. 2 camshaft bearing cap.
- Do not install any camshaft bearing caps other than the No. 1 camshaft bearing cap and No. 2 camshaft bearing cap.
(e) Slide the camshaft timing gear assembly and camshaft timing exhaust gear assembly as shown in the illustration. NOTICE: Securely insert the straight pins of the camshaft and No. 2 camshaft into the pin holes of the camshaft timing gear assembly and camshaft timing exhaust gear assembly. |
![]() |
21. TEMPORARILY INSTALL CAMSHAFT TIMING GEAR BOLT (for Intake Side of Bank 1)
(a) Check that there is no clearance between the camshaft timing gear assembly and camshaft flange.
(b) Apply engine oil to the areas of the camshaft timing gear bolt shown in the illustration. |
![]() |
(c) Use a wrench to hold the hexagonal portion of the camshaft.
*a |
Hold |
![]() |
Turn |
(d) Temporarily install the camshaft timing gear bolt.
Torque:
10 N·m {102 kgf·cm, 7 ft·lbf}
NOTICE:
- Installing the camshaft timing gear bolt while there is external force applied to the camshaft timing gear assembly could result in damage to the engine, so make sure that the camshaft bearing cap is not installed when temporarily installing the camshaft timing gear bolt.
- Be careful not to damage the camshaft, camshaft housing sub-assembly or spark plug tube with the wrench.
- Make sure that the flange part of the camshaft timing gear bolt is directly contacting the camshaft timing gear assembly.
22. TEMPORARILY INSTALL CAMSHAFT TIMING GEAR BOLT (for Exhaust Side of Bank 1)
(a) Check that there is no clearance between the camshaft timing exhaust gear assembly and No. 2 camshaft flange.
(b) Apply engine oil to the areas of the camshaft timing gear bolt shown in the illustration. |
![]() |
(c) Use a wrench to hold the hexagonal portion of the No. 2 camshaft.
*a |
Hold |
![]() |
Turn |
(d) Temporarily install the camshaft timing gear bolt.
Torque:
10 N·m {102 kgf·cm, 7 ft·lbf}
NOTICE:
- Installing the camshaft timing gear bolt while there is external force applied to the camshaft timing exhaust gear assembly could result in damage to the engine, so make sure that the camshaft bearing cap is not installed when temporarily installing the camshaft timing gear bolt.
- Be careful not to damage the No. 2 camshaft, camshaft housing sub-assembly or spark plug tube with the wrench.
- Make sure that the flange part of the camshaft timing gear bolt is directly contacting the camshaft timing exhaust gear assembly.
23. INSTALL CAMSHAFT BEARING CAP (for Bank 1)
(a) Clean the camshaft bearing caps and apply engine oil to them.
(b) Check the marks and numbers on the camshaft bearing caps, and then remove the replacement bolts and washers in the order shown in the illustration. Immediately after removing the replacement bolts and washers in the location for a camshaft bearing cap, install the camshaft bearing cap with the bolts in the order shown in the illustration.
Torque:
Bolt (A) :
28 N·m {286 kgf·cm, 21 ft·lbf}
Bolt (B), (C) :
16 N·m {163 kgf·cm, 12 ft·lbf}
NOTICE:
- Be sure to follow the numerical order when performing this procedure.
- Do not drop replacement bolts and washers into the cylinder head sub-assembly.
*a |
Replacement Bolt and Washer |
*b |
Replacement Bolt and Washer Removal |
*c |
Part Installation |
![]() |
Bolt (A) |
![]() |
Bolt (B) |
![]() |
Bolt (C) |
(c) Check the torque of each bolt again.
24. TIGHTEN CAMSHAFT TIMING GEAR BOLT (for Intake Side of Bank 1)
(a) Use a wrench to hold the hexagonal portion of the camshaft.
*a |
Hold |
![]() |
Turn |
(b) Tighten the camshaft timing gear bolt.
Torque:
95 N·m {969 kgf·cm, 70 ft·lbf}
NOTICE:
Be careful not to damage the camshaft, camshaft housing sub-assembly or spark plug tube with the wrench.
25. TIGHTEN CAMSHAFT TIMING GEAR BOLT (for Exhaust Side of Bank 1)
(a) Use a wrench to hold the hexagonal portion of the No. 2 camshaft.
*a |
Hold |
![]() |
Turn |
(b) Tighten the camshaft timing gear bolt.
Torque:
95 N·m {969 kgf·cm, 70 ft·lbf}
NOTICE:
Be careful not to damage the No. 2 camshaft, camshaft housing sub-assembly or spark plug tube with the wrench.
26. INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY
(a) Install the No. 2 chain tensioner assembly with the bolt.
Torque:
21 N·m {214 kgf·cm, 15 ft·lbf}
27. CONNECT CHAIN SUB-ASSEMBLY (for Bank 1)
(a) Align the paint marks on the camshaft timing gear assembly and chain sub-assembly and install the chain sub-assembly to the camshaft timing gear assembly. HINT: If the paint marks are not aligned, align them by turning the camshaft slightly. |
|
28. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY
(a) Turn the crankshaft counterclockwise 30° past the "0" timing mark, and then turn it clockwise to align the notch with the "0" timing mark. |
![]() |
(b) Turn the crankshaft slightly to eliminate the slack in the chain sub-assembly.
HINT:
Make sure there is some slack in the chain sub-assembly around the area where the No. 1 chain tensioner assembly is installed.
(c) Turn the stopper plate clockwise to release the lock, and push the plunger deep into the No. 1 chain tensioner assembly. |
|
(d) Turn the stopper plate counterclockwise to set the lock, and insert a 1.0 mm (0.0394 in.) diameter pin into the hole of the stopper plate.
(e) Install the No. 1 chain tensioner assembly to the cylinder head sub-assembly with the 2 bolts.
Torque:
10 N·m {102 kgf·cm, 7 ft·lbf}
(f) Remove the 1.0 mm (0.0394 in.) diameter pin from the No. 1 chain tensioner assembly.
29. INSPECT VALVE TIMING
(a) Check the camshaft timing marks.
NOTICE:
- Check each timing mark from a viewpoint directly in line with the center of the camshaft and the timing mark on each camshaft timing gear assembly and each camshaft timing exhaust gear assembly.
- If the timing marks are checked from any other viewpoint, the valve timing may appear misaligned.
(b) Check that each camshaft timing mark is positioned as shown in the illustration.
*a |
Timing Mark |
*b |
Viewpoint |
HINT:
For the camshaft or No. 3 camshaft sub-assembly:
Be sure to check mark (A) at the point where marks (B), (C) and (D) are positioned in line. If the marks are checked from any other viewpoint, they cannot be checked correctly.
(c) If the valve timing is misaligned, reinstall the chain sub-assembly.
(d) Turn the crankshaft 2 revolutions, set the No. 1 cylinder to TDC/compression and check the timing marks again.
30. INSTALL TIMING CHAIN COVER PLATE
Click here ![]()
31. INSTALL SPARK PLUG TUBE GASKET
Click here ![]()
32. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH
Click here ![]()
33. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
Click here ![]()
34. INSTALL CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 2)
Click here ![]()
35. INSTALL CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 2)
Click here ![]()
36. INSTALL CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 1)
Click here ![]()
37. INSTALL CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 1)
Click here ![]()
38. INSTALL WATER FILLER BRACKET
Click here ![]()
39. INSTALL WIRE HARNESS CLAMP BRACKET
Click here ![]()
40. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
Click here ![]()
41. INSTALL VACUUM PUMP ASSEMBLY
Click here ![]()
42. INSTALL IGNITION COIL ASSEMBLY
Click here ![]()
43. INSTALL AIR SURGE TANK TO INTAKE MANIFOLD GASKET
Click here ![]()
44. INSTALL INTAKE AIR SURGE TANK ASSEMBLY
Click here ![]()
45. CONNECT PURGE VALVE (PURGE VSV)
Click here ![]()
46. CONNECT VENTILATION HOSE
Click here ![]()
47. INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY
Click here ![]()
48. INSTALL ENGINE HANGERS
Click here ![]()
49. REMOVE ENGINE ASSEMBLY FROM ENGINE STAND
Click here ![]()
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during camshaft removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/ReplacedReplaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
Battery terminal is disconnected/reconnected |
Perform steering sensor zero point calibration |
Lane departure alert system (w/ Steering Control) |
|
Pre-collision system |
|||
Intelligent Clearance Sonar System*1 |
|||
Lighting System (for Gasoline Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking Assist Monitor System |
||
Panoramic View Monitor System |
|||
Replacement of ECM |
Vehicle Identification Number (VIN) registration |
MIL comes on |
|
ECU communication ID registration (Immobiliser system) |
Engine start function |
||
|
Inspection after repair |
|
|
Replacement of automatic transaxle assembly |
|
|
|
Replacement of ECM (If transaxle compensation code read from ECM) |
|
||
Replacement of ECM (If transaxle compensation code not read from ECM) |
|
||
Replacement of automatic transaxle fluid |
ATF thermal degradation estimate reset |
The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly |
|
Replacement of ECM |
Code registration (Smart Key System (for Start Function)) |
|
|
Suspension, tires, etc. |
|
|
|
Rear television camera assembly optical axis adjustment (Back camera position setting) |
Parking Assist Monitor System |
|
|
|
Panoramic View Monitor System |
|
|
Perform headlight ECU sub-assembly LH initialization |
Lighting system (for Gasoline Model with Cornering Light) |
||
Front wheel alignment adjustment |
Perform system variant learning and acceleration sensor zero point calibration. |
|
- *1: When performing learning using the Techstream.
Click here

- *2: Not necessary when ECM replaced with new one.
PROCEDURE
1. INSTALL ENGINE ASSEMBLY TO ENGINE STAND
Click here ![]()
2. REMOVE ENGINE HANGERS
Click here ![]()
3. REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY
Click here ![]()
4. DISCONNECT VENTILATION HOSE
Click here ![]()
5. DISCONNECT PURGE VALVE (PURGE VSV)
Click here ![]()
6. REMOVE NO. 2 SURGE TANK STAY
Click here ![]()
7. REMOVE INTAKE AIR SURGE TANK ASSEMBLY
Click here ![]()
8. REMOVE AIR SURGE TANK TO INTAKE MANIFOLD GASKET
Click here ![]()
9. REMOVE IGNITION COIL ASSEMBLY
Click here ![]()
10. REMOVE VACUUM PUMP ASSEMBLY
Click here ![]()
11. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
Click here ![]()
12. REMOVE WIRE HARNESS CLAMP BRACKET
Click here ![]()
13. REMOVE WATER FILLER BRACKET
Click here ![]()
14. REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 1)
Click here ![]()
15. REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 1)
Click here ![]()
16. REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 2)
Click here ![]()
17. REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 2)
Click here ![]()
18. REMOVE VVT SENSOR (for Intake Side of Bank 1)
Click here ![]()
19. REMOVE VVT SENSOR (for Exhaust Side of Bank 1)
Click here ![]()
20. REMOVE VVT SENSOR (for Intake Side of Bank 2)
Click here ![]()
21. REMOVE VVT SENSOR (for Exhaust Side of Bank 2)
Click here ![]()
22. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
Click here ![]()
23. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH
Click here ![]()
24. REMOVE SPARK PLUG TUBE GASKET
Click here ![]()
25. REMOVE TIMING CHAIN COVER PLATE
Click here ![]()
26. SET NO. 1 CYLINDER TO TDC (COMPRESSION)
(a) Turn the crankshaft clockwise to align the timing mark (cutout) on the crankshaft pulley with the "0" timing mark on the timing chain cover assembly. |
|
(b) Check that the timing marks of the camshaft timing gear assemblies are aligned with the timing marks of the camshaft bearing caps as shown in the illustration. HINT: If the marks are not aligned, turn the crankshaft again to align the marks. |
|
(c) Place paint marks on the timing marks and sprockets of each camshaft timing gear assembly and on the links of the chain sub-assembly.
HINT:
Be sure to place the paint marks on 2 links of the chain sub-assembly and on the sprockets of the camshaft timing gear assemblies at the locations of the timing marks of the camshaft timing gear assemblies.
27. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY
(a) Turn the crankshaft approximately 30° counterclockwise so that there is some slack in the chain sub-assembly. HINT: This prevents the valves and pistons from interfering with each other. |
![]() |
(b) Align the hole in the lever of the No. 1 chain tensioner assembly with the hole in the tensioner body as shown in the illustration, and then insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole. NOTICE: Check that the pin is locked. |
|
(c) Turn the crankshaft clockwise to align the timing mark (cutout) on the crankshaft pulley with the "0" timing mark on the timing chain cover assembly. |
|
(d) Remove the 2 bolts and No. 1 chain tensioner assembly from the cylinder head sub-assembly. NOTICE: Do not drop the No. 1 chain tensioner assembly or bolts into the timing chain cover assembly. |
![]() |
28. DISCONNECT CHAIN SUB-ASSEMBLY (for Bank 1)
(a) Turn the crankshaft clockwise until it is in the position shown in the illustration so that there is some slack in the chain sub-assembly between the banks. CAUTION: As the camshafts may turn suddenly, do not touch the camshafts or camshaft timing gears. HINT: When turning the crankshaft, engine oil may spray out of the oil holes. |
![]() |
(b) Turn the crankshaft clockwise until it is in the position shown in the illustration so that the chain sub-assembly can be removed easily. HINT: When turning the crankshaft, engine oil may spray out of the oil holes. |
|
(c) Remove the chain sub-assembly from the sprocket of the camshaft timing gear assembly and set it on the camshaft timing gear assembly. CAUTION: As the camshaft may turn suddenly and pinch your fingers when the chain sub-assembly is removed, pinch the chain sub-assembly and lift it upward to remove it from the sprocket. |
![]() |
29. SEPARATE NO. 2 CHAIN TENSIONER ASSEMBLY
(a) Remove the bolt to separate the No. 2 chain tensioner assembly from the camshaft housing sub-assembly. |
![]() |
30. REMOVE CAMSHAFT TIMING GEAR BOLT (for Intake Side of Bank 1)
(a) Use a wrench to hold the hexagonal portion of the camshaft and remove the camshaft timing gear bolt from the camshaft timing gear assembly.
*a |
Hold |
![]() |
Turn |
NOTICE:
- Be careful not to damage the camshaft, camshaft housing sub-assembly or spark plug tube with the wrench.
- If the camshaft timing gear bolt has been struck or dropped, replace it.
31. REMOVE CAMSHAFT TIMING GEAR BOLT (for Exhaust Side of Bank 1)
(a) Use a wrench to hold the hexagonal portion of the No. 2 camshaft and remove the camshaft timing gear bolt from the camshaft timing exhaust gear assembly.
NOTICE:
- Be careful not to damage the No. 2 camshaft, camshaft housing sub-assembly or spark plug tube with the wrench.
- If the camshaft timing gear bolt has been struck or dropped, replace it.
*a |
Hold |
![]() |
Turn |
32. REMOVE CAMSHAFT BEARING CAP (for Bank 1)
(a) Slide the camshaft timing gear assembly and camshaft timing exhaust gear assembly as shown in the illustration. |
![]() |
(b) Remove the bolts and camshaft bearing caps in the order shown in the illustration. Immediately after removing a camshaft bearing cap, install replacement bolts and washers in the order shown in the illustration. Torque: 10 N·m {102 kgf·cm, 7 ft·lbf} NOTICE:
HINT:
|
|
33. REMOVE NO. 2 CAMSHAFT
(a) While lifting up the camshaft timing exhaust gear assembly, remove the No. 2 chain tensioner assembly. |
![]() |
(b) Lift up the rear of the No. 2 camshaft so that it is at an angle.
(c) Pull the No. 2 camshaft as shown in the illustration to remove it from the camshaft timing exhaust gear assembly. |
![]() |
34. REMOVE CAMSHAFT
(a) Lift up the rear of the camshaft so that it is at an angle.
(b) Pull the camshaft as shown in the illustration to remove it from the camshaft timing gear assembly. |
![]() |
35. REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY (for Bank 1)
(a) Remove the camshaft timing exhaust gear assembly. |
![]() |
36. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY (for Bank 1)
(a) Remove the camshaft timing gear assembly and No. 2 chain sub-assembly. NOTICE: Do not drop the chain sub-assembly into the gap between the engine and timing chain cover assembly. |
![]() |
(b) Suspend the chain sub-assembly with a string or equivalent. |
![]() |
37. DISCONNECT CHAIN SUB-ASSEMBLY (for Bank 2)
(a) Turn the crankshaft counterclockwise to align the timing mark (cutout) on the crankshaft pulley with the "0" timing mark on the timing chain cover assembly. |
|
(b) Remove the chain sub-assembly from the sprocket of the camshaft timing gear assembly and set it on the camshaft timing gear assembly. CAUTION: As the camshaft may turn suddenly and pinch your fingers when the chain sub-assembly is removed, pinch the chain sub-assembly and lift it upward to remove it from the sprocket. |
![]() |
38. SEPARATE NO. 3 CHAIN TENSIONER ASSEMBLY
(a) Remove the bolt to separate the No. 3 chain tensioner assembly from the camshaft housing sub-assembly LH. |
![]() |
39. REMOVE CAMSHAFT TIMING GEAR BOLT (for Intake Side of Bank 2)
(a) Use a wrench to hold the hexagonal portion of the No. 3 camshaft sub-assembly and remove the camshaft timing gear bolt from the camshaft timing gear assembly.
*a |
Hold |
![]() |
Turn |
NOTICE:
- Be careful not to damage the No. 3 camshaft sub-assembly, camshaft housing sub-assembly LH or spark plug tube with the wrench.
- If the camshaft timing gear bolt has been struck or dropped, replace it.
40. REMOVE CAMSHAFT TIMING GEAR BOLT (for Exhaust Side of Bank 2)
(a) Use a wrench to hold the hexagonal portion of the No. 4 camshaft sub-assembly and remove the camshaft timing gear bolt from the camshaft timing exhaust gear assembly.
*a |
Hold |
![]() |
Turn |
NOTICE:
- Be careful not to damage the No. 4 camshaft sub-assembly, camshaft housing sub-assembly LH or spark plug tube with the wrench.
- If the camshaft timing gear bolt has been struck or dropped, replace it.
41. REMOVE CAMSHAFT BEARING CAP (for Bank 2)
(a) Slide the camshaft timing gear assembly and camshaft timing exhaust gear assembly as shown in the illustration. |
![]() |
(b) Remove the bolts and camshaft bearing caps in the order shown in the illustration. Immediately after removing a camshaft bearing cap, install replacement bolts and washers in the order shown in the illustration. Torque: 10 N·m {102 kgf·cm, 7 ft·lbf} NOTICE:
HINT:
|
|
42. REMOVE NO. 4 CAMSHAFT SUB-ASSEMBLY
(a) While lifting up the camshaft timing exhaust gear assembly, remove the No. 3 chain tensioner assembly. |
![]() |
(b) Lift up the rear of the No. 4 camshaft sub-assembly so that it is at an angle.
(c) Pull the No. 4 camshaft sub-assembly as shown in the illustration to remove it from the camshaft timing exhaust gear assembly. |
![]() |
43. REMOVE NO. 3 CAMSHAFT SUB-ASSEMBLY
(a) Lift up the rear of the No. 3 camshaft sub-assembly so that it is at an angle.
(b) Pull the No. 3 camshaft sub-assembly as shown in the illustration to remove it from the camshaft timing gear assembly. |
![]() |
44. REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY (for Bank 2)
(a) Remove the camshaft timing exhaust gear assembly. |
![]() |
45. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY (for Bank 2)
(a) Remove the camshaft timing gear assembly and No. 2 chain sub-assembly. NOTICE: Do not drop the chain sub-assembly into the gap between the engine and timing chain cover assembly. |
![]() |
(b) Suspend the chain sub-assembly with a string or equivalent. |
![]() |





























































