Rear Crankshaft Oil Seal
Components
COMPONENTS
ILLUSTRATION
*1 |
REAR ENGINE OIL SEAL |
*2 |
NO. 1 CRANKSHAFT POSITION SENSOR PLATE |
*3 |
DRIVE PLATE AND RING GEAR SUB-ASSEMBLY |
*4 |
REAR DRIVE PLATE SPACER |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
![]() |
MP grease |
![]() |
Adhesive 1324 |
★ |
Precoated part |
- |
- |
Installation
INSTALLATION
PROCEDURE
1. INSTALL REAR ENGINE OIL SEAL
(a) Using height adjustment attachments and plate lift attachments, place the engine assembly on a flat level surface.
NOTICE:
- Using height adjustment attachments and plate lift attachments, keep the engine assembly level.
- To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments under the No. 2 oil pan sub-assembly of the engine assembly.
- Using an engine sling device and engine lift, secure the engine assembly before servicing.
(b) Apply MP grease to the lip of a new rear engine oil seal. NOTICE:
|
|
(c) Using SST and a hammer, tap in the rear engine oil seal.
SST: 09223-15030
SST: 09950-70010
09951-07150
Oil Seal Protrusion Height:
-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)
NOTICE:
Do not tap in the rear engine oil seal at an angle.
2. INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE
(a) Install the No. 1 crankshaft position sensor plate. HINT: Align the pin of the No. 1 crankshaft position sensor plate with the pin hole of the crankshaft. |
![]() |
3. INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY
(a) Using SST, hold the crankshaft pulley. SST: 09213-70011 09213-70020 SST: 09330-00021 |
![]() |
(b) Clean the 8 bolts and 8 bolt holes.
(c) Install the drive plate and ring gear sub-assembly and rear drive plate spacer to the crankshaft.
*1 |
Drive Plate and Ring Gear Sub-assembly |
*2 |
Rear Drive Plate Spacer |
![]() |
Transaxle Side |
(d) Apply adhesive to 2 or 3 threads at the end of each of the 8 bolts. Adhesive: Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent |
|
(e) Install and uniformly tighten the 8 bolts in several steps in the sequence shown in the illustration. Torque: 83 N·m {846 kgf·cm, 61 ft·lbf} NOTICE: Do not start the engine for at least 1 hour after installing the drive plate and ring gear sub-assembly. |
![]() |
4. INSTALL AUTOMATIC TRANSAXLE ASSEMBLY
Click here ![]()
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear crankshaft oil seal removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/ReplacedReplaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
Battery terminal is disconnected/reconnected |
Perform steering sensor zero point calibration |
Lane departure alert system (w/ Steering Control) |
|
Pre-collision system |
|||
Intelligent Clearance Sonar System*1 |
|||
Lighting System (for Gasoline Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking Assist Monitor System |
||
Panoramic View Monitor System |
|||
Replacement of ECM |
Vehicle Identification Number (VIN) registration |
MIL comes on |
|
ECU communication ID registration (Immobiliser system) |
Engine start function |
||
Gas leak from exhaust system is repaired |
Inspection after repair |
|
|
Replacement of automatic transaxle assembly |
|
|
|
Replacement of ECM (If transaxle compensation code read from ECM) |
|
||
Replacement of ECM (If transaxle compensation code not read from ECM) |
|
||
Replacement of automatic transaxle fluid |
ATF thermal degradation estimate reset |
The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly |
|
Replacement of ECM |
Code registration (Smart Key System (for Start Function)) |
|
|
Suspension, tires, etc. |
|
|
|
Rear television camera assembly optical axis adjustment (Back camera position setting) |
Parking Assist Monitor System |
|
|
|
Panoramic View Monitor System |
|
|
Perform headlight ECU sub-assembly LH initialization |
Lighting system (for Gasoline Model with Cornering Light) |
||
Front wheel alignment adjustment |
Perform system variant learning and acceleration sensor zero point calibration. |
|
- *1: When performing learning using the Techstream.
Click here

- *2: Not necessary when ECM replaced with new one.
PROCEDURE
1. REMOVE AUTOMATIC TRANSAXLE ASSEMBLY
Click here ![]()
2. REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY
(a) Using height adjustment attachments and plate lift attachments, place the engine assembly on a flat level surface.
NOTICE:
- Using height adjustment attachments and plate lift attachments, keep the engine assembly level.
- To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments under the No. 2 oil pan sub-assembly of the engine assembly.
- Using an engine sling device and engine lift, secure the engine assembly before servicing.
(b) Using SST, hold the crankshaft pulley. SST: 09213-70011 09213-70020 SST: 09330-00021 |
![]() |
(c) Remove the 8 bolts, the rear drive plate spacer, the drive plate and ring gear sub-assembly. |
![]() |
3. REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE
(a) Remove the No. 1 crankshaft position sensor plate.
4. REMOVE REAR ENGINE OIL SEAL
(a) Using a knife, cut through the lip of the rear engine oil seal. |
|
(b) Using a screwdriver with its tip wrapped with protective tape, pry out the rear engine oil seal.
NOTICE:
Be careful not to damage the crankshaft.











