Ecm
Components
COMPONENTS
ILLUSTRATION
*1 |
LUGGAGE TRIM SERVICE HOLE COVER |
- |
- |
ILLUSTRATION
*1 |
ECM |
*2 |
NO. 1 ECM BRACKET |
*3 |
NO. 2 ECM BRACKET |
- |
- |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
- |
- |
Installation
INSTALLATION
PROCEDURE
1. INSTALL NO. 2 ECM BRACKET
(a) Install the No. 2 ECM bracket to the ECM with the 2 screws.
Torque:
4,5 N·m {46 kgf·cm, 40 in·lbf}
2. INSTALL NO. 1 ECM BRACKET
(a) Install the No. 1 ECM bracket to the ECM with the 2 screws.
Torque:
4,5 N·m {46 kgf·cm, 40 in·lbf}
3. INSTALL ECM
(a) Install the ECM with the 2 nuts in the order shown in the illustration. Torque: 8 N·m {82 kgf·cm, 71 in·lbf} NOTICE: If the ECM has been struck or dropped, replace it. |
![]() |
(b) Engage the clamp. |
![]() |
(c) Install the engine wire to the No. 2 ECM bracket with the bolt.
Torque:
10 N·m {102 kgf·cm, 7 ft·lbf}
(d) Connect the 2 ECM connectors and rotate the 2 levers to lock them.
NOTICE:
- When connecting the ECM connectors, make sure that the connecting parts of the ECM connectors are free of dirt, water and other foreign matter.
- Be sure to securely connect the ECM connectors.
4. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
Click here ![]()
5. INSTALL LUGGAGE TRIM SERVICE HOLE COVER
Click here ![]()
6. PERFORM INITIALIZATION
Click here ![]()
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during ECM removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/ReplacedReplaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
| *: When performing learning using the Techstream. Click here |
|||
Auxiliary battery terminal is disconnected/reconnected |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
Pre-collision System |
|||
Intelligent Clearance Sonar System* |
|||
Lighting System (for HV Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking Assist Monitor System |
||
Panoramic View Monitor System |
|||
Replacement of ECM |
Perform Vehicle Identification Number (VIN) registration |
MIL illuminates |
|
NOTICE:
- After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here

- If the ECM has been struck or dropped, replace it.
- Perform Vehicle Identification Number (VIN) registration when replacing the ECM.
Click here

PROCEDURE
1. REMOVE LUGGAGE TRIM SERVICE HOLE COVER
Click here ![]()
2. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
Click here ![]()
3. REMOVE ECM
(a) Rotate the 2 levers while pushing the locks, and disconnect the 2 ECM connectors. NOTICE: After disconnecting the ECM connectors, make sure that dirt, water and other foreign matter does not contact the connecting parts of the ECM connectors. |
![]() |
(b) Remove the bolt and separate the engine wire from the No. 2 ECM bracket.
(c) Disengage the clamp.
(d) Remove the 2 nuts and ECM. NOTICE: If the ECM has been struck or dropped, replace it. |
![]() |
4. REMOVE NO. 1 ECM BRACKET
(a) Remove the 2 screws and No. 1 ECM bracket from the ECM. |
![]() |
5. REMOVE NO. 2 ECM BRACKET
(a) Remove the 2 screws and No. 2 ECM bracket from the ECM. |
![]() |






