Oil Level Sensor
Components
COMPONENTS
ILLUSTRATION
*1 |
ENGINE OIL LEVEL SENSOR |
*2 |
NO. 2 OIL PAN SUB-ASSEMBLY |
*3 |
OIL STRAINER SUB-ASSEMBLY |
*4 |
OIL STRAINER GASKET |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
Inspection
INSPECTION
PROCEDURE
1. INSPECT ENGINE OIL LEVEL SENSOR
(a) Measure the resistance according to the value(s) in the table below. Standard Resistance:
If the result is not as specified, replace the engine oil level sensor. |
|
Installation
INSTALLATION
PROCEDURE
1. INSTALL ENGINE OIL LEVEL SENSOR
(a) Install the engine oil level sensor to the oil pan sub-assembly with the 2 nuts.
Torque:
10 N·m {102 kgf·cm, 7 ft·lbf}
(b) Install a new clip to the engine oil level sensor.
2. INSTALL OIL STRAINER SUB-ASSEMBLY
Click here ![]()
3. INSTALL NO. 2 OIL PAN SUB-ASSEMBLY
Click here ![]()
4. REMOVE ENGINE ASSEMBLY FROM ENGINE STAND
Click here ![]()
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during engine oil level sensor removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/ReplacedReplaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
Battery terminal is disconnected/reconnected |
Perform steering sensor zero point calibration |
Lane departure alert system (w/ Steering Control) |
|
Pre-collision system |
|||
Intelligent Clearance Sonar System* |
|||
Lighting System (for Gasoline Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking Assist Monitor System |
||
Panoramic View Monitor System |
|||
Replacement of ECM |
Vehicle Identification Number (VIN) registration |
MIL comes on |
|
ECU communication ID registration (Immobiliser system) |
Engine start function |
||
|
Inspection after repair |
|
|
Replacement of automatic transaxle assembly |
|
|
|
Replacement of ECM (If transaxle compensation code read from ECM) |
|
||
Replacement of ECM (If transaxle compensation code not read from ECM) |
|
||
Replacement of automatic transaxle fluid |
ATF thermal degradation estimate reset |
The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly |
|
Replacement of ECM |
Code registration (Smart Key System (for Start Function)) |
|
|
Suspension, tires, etc. |
|
|
|
Rear television camera assembly optical axis adjustment (Back camera position setting) |
Parking Assist Monitor System |
|
|
|
Panoramic View Monitor System |
|
|
Perform headlight ECU sub-assembly LH initialization |
Lighting system (for Gasoline Model with Cornering Light) |
||
Front wheel alignment adjustment |
Perform system variant learning and acceleration sensor zero point calibration. |
|
- *1: When performing learning using the Techstream.
Click here

- *2: Not necessary when ECM replaced with new one.
PROCEDURE
1. INSTALL ENGINE ASSEMBLY TO ENGINE STAND
Click here ![]()
2. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY
Click here ![]()
3. REMOVE OIL STRAINER SUB-ASSEMBLY
Click here ![]()
4. REMOVE ENGINE OIL LEVEL SENSOR
(a) Remove the clip from the engine oil level sensor. |
![]() |
(b) Remove the 2 nuts and engine oil level sensor from the oil pan sub-assembly. |
![]() |



