Hybrid/EV Battery Voltage Isolation Sensor Circuit Internal Electronic Failure (P0AA749). Hybrid/EV Battery Air Temperature Sensor "A" Circuit Short to Ground (P0AAC11,P0AAC15). Hybrid/EV Battery Curr
Hybrid/EV Battery Voltage Isolation Sensor Circuit Internal Electronic Failure (P0AA749)
DESCRIPTION
The hybrid vehicle control ECU monitors the insulation monitoring circuit located in the battery voltage sensor and detects malfunctions.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
P0AA749 |
Hybrid/EV Battery Voltage Isolation Sensor Circuit Internal Electronic Failure |
Malfunction in the insulation monitoring circuit in the battery voltage sensor (1 trip detection logic) |
Battery voltage sensor |
Does not come on |
Master Warning Light: Comes on |
DTC No. | Data List |
|---|---|
P0AA749 |
Short Wave Highest Value Level |
CONFIRMATION DRIVING PATTERN
HINT:
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here ![]()
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG) and turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the power switch off and wait for 2 minutes or more.
- Turn the power switch on (IG) and turn the Techstream on.
- With power switch on (IG) and wait for 70 seconds or more.
- Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
- Check the DTC judgment result.
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.
PROCEDURE
CLEAR DTC
Click here ![]()
|
SIMULATION TEST
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG) and wait for 70 seconds or more.
NOTICE:
Do not turn the power switch off until step 3 is complete.
(c) Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
(d) Check if DTCs are output.
Powertrain > Hybrid Control > Trouble CodesResult | Proceed to |
|---|---|
P0AA749 is not output. |
A |
P0AA749 is output. |
B |
| B | REPLACE BATTERY VOLTAGE SENSOR |
|
SIMULATION TEST
NOTICE:
Do not turn the power switch off while performing this inspection.
(a) With the vehicle and engine stopped, turn the power switch on (READY) with shift lever in P and wait for 70 seconds or more. (If the engine starts, wait until the engine stops.)
(b) While depressing the brake pedal without depressing the accelerator pedal, move the shift lever to D and wait for 1 minute. (Step A)
(c) Drive the vehicle 0.5 m (1.6 ft.) forward and perform step A.
(d) Drive the vehicle another 0.5 m (1.6 ft.) forward and perform step A. Repeat this procedure 5 times (minimum total driving distance: 2 m (6.6 ft.)).
(e) Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
(f) Check if DTCs are output.
Powertrain > Hybrid Control > Trouble CodesResult | Proceed to |
|---|---|
P0AA649 is not output. |
A |
P0AA649 is output. |
B |
| A | REPLACE BATTERY VOLTAGE SENSOR |
| B | GO TO DTC CHART (P0AA649) |
Hybrid/EV Battery Air Temperature Sensor "A" Circuit Short to Ground (P0AAC11,P0AAC15)
DESCRIPTION
The inlet air temperature sensor (battery) is mounted on the HV battery. The resistance of the sensor varies in accordance with changes in the intake air temperature. The characteristics of the inlet air temperature sensor are the same as those of the battery temperature sensors (Click here
). The battery voltage sensor uses signals from the inlet air temperature sensor to control the air volume of the battery cooling blower assembly.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
P0AAC11 |
Hybrid/EV Battery Air Temperature Sensor "A" Circuit Short to Ground |
The inlet air temperature sensor output voltage is lower than the specified value (short circuit) and the detected temperature is higher than the specified value. (1 trip detection logic) |
|
Does not come on |
Master Warning Light: Comes on |
P0AAC15 |
Hybrid/EV Battery Air Temperature Sensor "A" Circuit Short to Auxiliary Battery or Open |
The inlet air temperature sensor output voltage is higher than the standard value (short to +B or open) and the detected temperature is lower than the specified value. (1 trip detection logic) |
|
Does not come on |
Master Warning Light: Comes on |
HINT:
After checking for the above DTCs, check the hybrid system Data List item "Hybrid Battery Cooling Fan Intake Air Temperature 1" using the Techstream.
Displayed Temperature | Malfunction |
|---|---|
-45°C (-49°F) or less |
Open or +B short circuit |
95 °C or more |
GND short |
DTC No. | Data List |
|---|---|
P0AAC11 |
Hybrid Battery Cooling Fan Intake Air Temperature 1 |
P0AAC15 |
CONFIRMATION DRIVING PATTERN
HINT:
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here ![]()
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG) and turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the power switch off and wait for 2 minutes or more.
- Turn the power switch on (IG) and turn the Techstream on.
- With power switch on (IG) and wait for 5 seconds or more.
- Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
- Check the DTC judgment result.
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.
WIRING DIAGRAM
Refer to the wiring diagram for DTC P0A9B2A.
Click here ![]()
CAUTION:
- Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.
- Inspecting the high-voltage system
- Disconnecting the low voltage connector of the inverter with converter assembly
- Disconnecting the low voltage connector of the HV battery
- To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

- After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

- After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.
Click here

HINT:
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
*a
Without waiting for 10 minutes
NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here ![]()
PROCEDURE
CHECK DTC OUTPUT (HYBRID CONTROL)
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
(d) Check for DTCs.
Powertrain > Hybrid Control > Trouble CodesResult | Proceed to |
|---|---|
P0AFC00, P0AFC96 or P308A12 is not output. |
A |
P0AFC00, P0AFC96 or P308A12 is output. |
B |
(e) Turn the power switch off.
| B | GO TO DTC CHART (HYBRID CONTROL SYSTEM) |
|
CHECK CONNECTOR CONNECTION CONDITION (INLET AIR TEMPERATURE SENSOR)
CAUTION:
Be sure to wear insulated gloves.
(a) Check that the service plug grip is not installed.
NOTICE:
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
(b) Remove the No. 1 hybrid battery exhaust duct.
Click here ![]()
(c) Check the connections of the y6 battery voltage sensor connector. Click here OK: The connector is connected securely and there are no contact problems. |
![]() |
(d) Install the No. 1 hybrid battery exhaust duct.
| NG | CONNECT SECURELY |
|
CHECK INSTALLATION OF INLET AIR TEMPERATURE SENSOR
CAUTION:
Be sure to wear insulated gloves and protective goggles.
(a) Check that the service plug grip is not installed.
NOTICE:
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
(b) Remove the upper HV battery cover sub-assembly.
Click here ![]()
(c) Visually check the installation condition of the inlet air temperature sensor.
|
![]() |
(d) Install the upper HV battery cover sub-assembly.
| B | REPLACE HYBRID BATTERY THERMISTOR |
| C | INSTALL PARTS CORRECTLY |
|
CHECK HV BATTERY (INLET AIR TEMPERATURE SENSOR)
CAUTION:
Be sure to wear insulated gloves.
(a) Check that the service plug grip is not installed.
NOTICE:
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
(b) Remove the No. 1 hybrid battery exhaust duct.
Click here ![]()
(c) Disconnect the y6 battery voltage sensor connector.
NOTICE:
Before disconnecting the connector, check that it is not loose or disconnected.
(d) Measure the resistance according to the value(s) in the table below. Standard Resistance:
NOTICE: When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder. |
|
(e) Disconnect the K17 battery voltage sensor connector.
(f) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
y6-1 (TC0) - K17-1 (IGCT) |
Power switch off |
10 kΩ or higher |
y6-1 (TC0) - K17-5 (GND) |
Power switch off |
10 kΩ or higher |
y6-7 (GC0) - K17-1 (IGCT) |
Power switch off |
10 kΩ or higher |
y6-7 (GC0) - K17-5 (GND) |
Power switch off |
10 kΩ or higher |
y6-4 (TB0) - K17-1 (IGCT) |
Power switch off |
10 kΩ or higher |
y6-4 (TB0) - K17-5 (GND) |
Power switch off |
10 kΩ or higher |
y6-10 (GB0) - K17-1 (IGCT) |
Power switch off |
10 kΩ or higher |
y6-10 (GB0) - K17-5 (GND) |
Power switch off |
10 kΩ or higher |
y6-3 (TB1) - K17-1 (IGCT) |
Power switch off |
10 kΩ or higher |
y6-3 (TB1) - K17-5 (GND) |
Power switch off |
10 kΩ or higher |
y6-9 (GB1) - K17-1 (IGCT) |
Power switch off |
10 kΩ or higher |
y6-9 (GB1) - K17-5 (GND) |
Power switch off |
10 kΩ or higher |
y6-2 (TB2) - K17-1 (IGCT) |
Power switch off |
10 kΩ or higher |
y6-2 (TB2) - K17-5 (GND) |
Power switch off |
10 kΩ or higher |
y6-8 (GB2) - K17-1 (IGCT) |
Power switch off |
10 kΩ or higher |
y6-8 (GB2) - K17-5 (GND) |
Power switch off |
10 kΩ or higher |
(g) Reconnect the y6 and K17 battery voltage sensor connectors.
(h) Install the No. 1 hybrid battery exhaust duct.
| OK | REPLACE BATTERY VOLTAGE SENSOR |
|
CHECK HARNESS AND CONNECTOR (BATTERY TEMPERATURE SENSOR AND INLET AIR TEMPERATURE SENSOR)
CAUTION:
Be sure to wear insulated gloves and protective goggles.
(a) Check that the service plug grip is not installed.
NOTICE:
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
(b) Remove the upper HV battery cover sub-assembly.
Click here ![]()
(c) Check the wire harnesses and connectors of the battery temperature sensors and inlet air temperature sensor for abnormalities by sight and touch.
Specified Condition:
There are no open or short circuits in the wire harnesses and connectors. There are no short circuits to other wire harnesses.
(d) Install the upper HV battery cover sub-assembly.
| OK | REPLACE HYBRID BATTERY THERMISTOR |
| NG | REPAIR HARNESS OR CONNECTOR (INLET AIR TEMPERATURE SENSOR) |
Hybrid/EV Battery Current Sensor "A" Circuit Range/Performance (P0ABF00)
DESCRIPTION
A battery current sensor is installed to the positive (+) terminal side of the HV battery and detects current flowing from the HV battery. The battery current sensor outputs voltage, which changes between 0 and 5 V according to the detected amperage, to the IB terminal of the battery voltage sensor. The battery voltage sensor sends signals to the hybrid vehicle control ECU. The hybrid vehicle control ECU determines the charging and discharging amount of the HV battery based on the received signals and calculates the SOC of the HV battery through the accumulated amperage.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
P0ABF00 |
Hybrid/EV Battery Current Sensor "A" Circuit Range/Performance |
Abnormal battery current sensor characteristics: (based on hybrid system consumption and HV battery output). (1 trip detection logic) |
|
Comes on |
Master Warning Light: Comes on |
DTC No. | Data List |
|---|---|
P0ABF00 |
- |
MONITOR DESCRIPTION
The hybrid vehicle control ECU detects malfunctions of the battery current sensor by monitoring motor and generator torque. If the hybrid vehicle control ECU detects a battery current sensor malfunction, the hybrid vehicle control ECU will illuminate the MIL and store a DTC.
MONITOR STRATEGY
Related DTCs |
P0AC0 (INF P0ABF00): Current sensor malfunction (gain or offset) |
Required sensors/components |
Battery current sensor |
Frequency of operation |
Continuous |
Duration |
TMC's intellectual property |
MIL operation |
1 driving cycle |
Sequence of operation |
None |
TYPICAL ENABLING CONDITIONS
The monitor will run whenever the following DTCs are not stored |
TMC's intellectual property |
Other conditions belong to TMC's intellectual property |
- |
TYPICAL MALFUNCTION THRESHOLDS
TMC's intellectual property |
- |
COMPONENT OPERATING RANGE
Hybrid vehicle control ECU |
DTC P0AC0 (INF P0ABF00) is not detected |
CONFIRMATION DRIVING PATTERN
HINT:
- After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here

- When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here

- Connect the Techstream to the DLC3.
- Turn the power switch on (IG) and turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the power switch off and wait for 2 minutes or more.
- Turn the power switch on (IG) and turn the Techstream on.
- Drive the vehicle for approximately 10 minutes according to the freeze frame data items "Vehicle Speed", "Accelerator Position", "Hybrid Battery Current", "Motor Torque" and "Generator Torque". [*1]
HINT:
[*1] : Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
- Check the DTC judgment result.
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.
PROCEDURE
CHECK DTC OUTPUT (HYBRID CONTROL)
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
(d) Check for DTCs.
Powertrain > Hybrid Control > Trouble CodesResult | Proceed to |
|---|---|
One of the followings applies:
|
A |
P0AFC00 or P0AFC96 is also output. |
B |
(e) Turn the power switch off.
(f) Disconnect the Techstream from the DLC3.
| B | GO TO DTC CHART (HYBRID CONTROL SYSTEM) |
|
CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - HV BATTERY JUNCTION BLOCK ASSEMBLY)
Click here ![]()
| NG | REPLACE HYBRID BATTERY THERMISTOR |
|
REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY
Click here ![]()
|
CLEAR DTC
Click here ![]()
|
PERFORM ROAD TEST
(a) Drive the vehicle for approximately 10 minutes according to the freeze frame data items "Vehicle Speed", "Accelerator Position", "Hybrid Battery Current", "Motor Torque" and "Generated Torque".
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
|
CHECK DTC OUTPUT (HYBRID CONTROL)
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
(d) Check for DTCs.
Powertrain > Hybrid Control > Trouble CodesResult | Proceed to |
|---|---|
P0ABF00 is not output. |
A |
P0ABF00 is output again. |
B |
(e) Turn the power switch off.
| A | END |
| B | REPLACE BATTERY VOLTAGE SENSOR |


