Hybrid/EV Battery State of Charge High (P0C3000). Motor Electronics Coolant Pump "A" Component Internal Failure (P0C7396). Hybrid/EV Battery System Discharge Time Too Long (P0C7600)
Hybrid/EV Battery State of Charge High (P0C3000)
DESCRIPTION
The hybrid vehicle control ECU monitors the system internal operation and will store a DTC and perform fail-safe control if it detects the following malfunction.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
P0C3000 |
Hybrid/EV Battery State of Charge High |
Charging prohibited Charging of the HV battery continues even after charging is prohibited when the hybrid system is malfunctioning and "Hybrid Battery SOC" has reached the upper limit. (1 trip detection logic) |
Hybrid vehicle control ECU |
Does not come on |
Master Warning Light: Comes on |
DTC No. | Data List |
|---|---|
P0C3000 |
|
CONFIRMATION DRIVING PATTERN
HINT:
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here ![]()
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG) and turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the power switch off and wait for 2 minutes or more.
- Turn the power switch on (IG) and turn the Techstream on.
- Apply the parking brake and secure the wheels using chocks.
- Fully apply the parking brake and chock all 4 wheels. Firmly depress the brake pedal, turn the power switch on (READY) and with the shift lever in D. Depress the accelerator pedal to start the engine and increase the engine speed. This will cause the "Hybrid Battery SOC" to increase.
If the charge current drops, release the accelerator pedal and then depress it again to maintain charging.
- Select "WIN Control Limit Power" in the Data List and check that charging stops when "WIN Control Limit Power" reaches 0 kW.
- Check that charging stops when the Data List item "Hybrid Battery SOC" reaches the upper limit.
- Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
- Check the DTC judgment result.
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.
PROCEDURE
CHECK DTC OUTPUT (HYBRID CONTROL)
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
(d) Check for DTCs.
Powertrain > Hybrid Control > Trouble CodesResult | Proceed to |
|---|---|
P0C3000 only is output. |
A |
DTCs except P0C3000 are output. |
B |
(e) Turn the power switch off.
| A | REPLACE HYBRID VEHICLE CONTROL ECU |
| B | GO TO DTC CHART (HYBRID CONTROL SYSTEM) |
Motor Electronics Coolant Pump "A" Component Internal Failure (P0C7396)
DTC SUMMARY
MALFUNCTION DESCRIPTION
This DTC is stored when the inverter water pump assembly is malfunctioning. The cause of this malfunction may be one of the following:
Inverter water pump assembly malfunction- Inverter water pump assembly internal malfunction
- Open or short in wire harness
- Improperly connected connector
- Foreign matter in inverter water pump assembly
- Hybrid cooling system coolant is frozen
HINT:
If this DTC is stored, the driving torque may be restricted.
DESCRIPTION
The inverter water pump assembly transmits rotation speed information to the hybrid vehicle control ECU. The hybrid vehicle control ECU monitors the speed and detects malfunctions.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
P0C7396 |
Motor Electronics Coolant Pump "A" Component Internal Failure |
The inverter water pump assembly revolution speed is abnormally high or low (or stopped) for 1 minute or more. (1 trip detection logic) |
|
Comes on |
Master Warning Light: Comes on |
HINT:
The inverter water pump assembly operates when the power switch is on (READY).
Related Data ListDTC No. | Data List |
|---|---|
P0C7396 |
|
DTC No. | Active Test |
|---|---|
P0C7396 |
Activate the Inverter Water Pump |
MONITOR DESCRIPTION
The hybrid vehicle control ECU monitors speed of the inverter water pump assembly. If there is an abnormality in speed, the hybrid vehicle control ECU will illuminate the MIL and store a DTC.
MONITOR STRATEGY
Related DTCs |
P0C73 (INF P0C7396): Motor Electronics Coolant Pump "A" malfunction |
Required sensors/components |
Inverter water pump assembly |
Frequency of operation |
Continuous |
Duration |
TMC's intellectual property |
MIL operation |
1 driving cycle |
Sequence of operation |
None |
TYPICAL ENABLING CONDITIONS
The monitor will run whenever the following DTCs are not stored |
TMC's intellectual property |
Other conditions belong to TMC's intellectual property |
- |
TYPICAL MALFUNCTION THRESHOLDS
TMC's intellectual property |
- |
COMPONENT OPERATING RANGE
Hybrid vehicle control ECU |
DTC P0C73 (INF P0C7396) is not detected |
CONFIRMATION DRIVING PATTERN
HINT:
- After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here

- When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here

- Connect the Techstream to the DLC3.
- Turn the power switch on (IG) and turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the power switch off and wait for 2 minutes or more.
- Turn the power switch on (IG) and turn the Techstream on.
- Turn the power switch on (READY). [*1]
- Wait for 2 minutes or more. [*2]
HINT:
[*1] to [*2] : Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
- Check the DTC judgment result.
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.
WIRING DIAGRAM
NOTICE:
If this vehicle is jump started, etc. and excessive voltage is applied to the auxiliary battery, the inverter water pump assembly may suspend control as a self-protection function and store DTCs.
(When the auxiliary battery voltage returns to normal, the inverter water pump assembly will resume normal operation. In this case it is not necessary to replace the inverter water pump assembly.)
PROCEDURE
CHECK DTC OUTPUT (HYBRID CONTROL)
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
(d) Check for DTCs.
Powertrain > Hybrid Control > Trouble CodesResult | Proceed to |
|---|---|
P0C7396 only is output, or DTCs except the ones in the table below are also output. |
A |
Any of the following DTCs including pending DTCs are also output. |
B |
Malfunction Content | Relevant DTC |
|
|---|---|---|
Microcomputer malfunction |
P060647 |
Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure |
P06881F |
ECM/PCM Power Relay Sense Circuit Intermittent |
|
Sensor and actuator circuit malfunction |
P314A31 |
Motor Electronics Coolant Pump "A" No Signal |
HINT:
P0C7396 may be output as a result of the malfunction indicated by the DTCs above.
- The chart above is listed in inspection order of priority.
- Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)
(e) Turn the power switch off.
| B | GO TO DTC CHART (HYBRID CONTROL SYSTEM) |
|
READ VALUE USING TECHSTREAM (INVERTER WATER PUMP REVOLUTION)
NOTICE:
Be sure to perform the inspection with the auxiliary battery voltage at 11 V or more.
HINT:
- When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.
- When the inverter water pump assembly signal line (SWP - IWP) is open or its connection is faulty, the inverter water pump assembly is operated forcibly.
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Enter the following menus: Powertrain / Hybrid Control / Data List / Inverter Water Pump Revolution.
Powertrain > Hybrid Control > Data ListInverter Water Pump Revolution
(d) According to the display on the Techstream, read the Data List.
OK:
Tester Display | Condition | Specified Condition |
|---|---|---|
Inverter Water Pump Revolution |
Power switch on (IG) |
200 rpm or less |
HINT:
When the inverter water pump assembly is not operating, the Data List item "Inverter Water Pump Revolution" displays a value 200 rpm or less.
(e) Turn the power switch off.
| NG | GO TO STEP 6 |
|
CLEAR DTC
Click here ![]()
|
PERFORM ACTIVE TEST USING TECHSTREAM (ACTIVATE THE INVERTER WATER PUMP)
NOTICE:
- Make sure that the HV coolant level is above the low line of the inverter reserve tank.
- Be sure to perform the inspection with the auxiliary battery voltage at 11 V or more.
HINT:
When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Enter the following menus: Powertrain / Hybrid Control / Active Test / Activate the Inverter Water Pump.
(d) Select the Data List item "Inverter Water Pump Revolution".
Powertrain > Hybrid Control > Active TestActivate the Inverter Water Pump
Inverter Water Pump Revolution
(e) According to the display on the Techstream, perform the Active Test "Activate the Inverter Water Pump" and, check the value of the Data List item "Inverter Water Pump Revolution".
OK:
Tester Display | Condition | Specified Condition |
|---|---|---|
Inverter Water Pump Revolution |
Power switch on (IG) During Active Test |
3176 to 8617 rpm |
HINT:
- Perform the Active Test with the inverter coolant temperature between -15 and 65 °C.
- When the inverter water pump assembly is not operating, the Data List item "Inverter Water Pump Revolution" displays a value 200 rpm or less.
(f) Turn the power switch off.
| NG | GO TO STEP 6 |
|
CHECK HV COOLANT (CHECK FOR CONDITIONS THAT MAY HAVE CAUSED FREEZING)
Click here ![]()
Result | Proceed to |
|---|---|
Ambient Temperature value is above freezing temperature of the HV coolant. |
A |
Ambient Temperature value is below freezing temperature of the HV coolant. |
B |
| A | GO TO STEP 12 |
| B | REPLACE HV COOLANT |
CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)
Click here ![]()
| NG | CONNECT SECURELY |
|
CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)
Click here ![]()
| NG | CONNECT SECURELY |
|
CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)
(a) Disconnect the A23 hybrid vehicle control ECU connector.
(b) Disconnect the X1 inverter water pump assembly connector.
(c) Measure the resistance according to the value(s) in the table below. Standard Resistance (Check for Open):
Standard Resistance (Check for Short):
|
|
(d) Reconnect the X1 inverter water pump assembly connector.
(e) Reconnect the A23 hybrid vehicle control ECU connector.
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
READ VALUE USING TECHSTREAM (INVERTER WATER PUMP REVOLUTION)
NOTICE:
Be sure to perform the inspection with the auxiliary battery voltage at 11 V or more.
HINT:
When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.
(a) Connect the Techstream to the DLC3.
(b) Remove the INV W/PMP fuse from No. 4 relay block. |
|
(c) Turn the power switch on (IG).
(d) Enter the following menus: Powertrain / Hybrid Control / Data List / Inverter Water Pump Revolution.
Powertrain > Hybrid Control > Data ListInverter Water Pump Revolution
(e) According to the display on the Techstream, read the Data List.
OK:
Tester Display | Condition | Specified Condition |
|---|---|---|
Inverter Water Pump Revolution |
Power switch on (IG) |
200 rpm or less |
(f) Turn the power switch off.
(g) Install the INV W/PMP fuse.
| NG | REPLACE HYBRID VEHICLE CONTROL ECU |
|
CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)
(a) Disconnect the A23 hybrid vehicle control ECU connector.
(b) Turn the power switch on (IG).
(c) Measure the voltage according to the value(s) in the table below. Standard Voltage:
NOTICE: Turning the power switch on (IG) with the hybrid vehicle control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection. |
|
(d) Turn the power switch off.
(e) Reconnect the A23 hybrid vehicle control ECU connector.
| NG | GO TO STEP 12 |
|
CHECK HYBRID VEHICLE CONTROL ECU (CHECK WAVEFORM)
(a) Connect an oscilloscope between the hybrid vehicle control ECU terminals specified in the table below.
(b) Check the waveform while turning the power switch on (IG).
OK: Waveform duty ratio is between 3% and 9%. |
|
(c) Turn the power switch off.
| NG | REPLACE HYBRID VEHICLE CONTROL ECU |
|
REPLACE INVERTER WATER PUMP ASSEMBLY
Click here ![]()
|
ADD HV COOLANT AND PERFORM AIR BLEEDING
(a) After replacing the inverter water pump assembly, add HV coolant and perform air bleeding.
Click here ![]()
| NEXT | END |
Hybrid/EV Battery System Discharge Time Too Long (P0C7600)
DTC SUMMARY
MALFUNCTION DESCRIPTION
When the power switch is turned from on (READY) to off, the hybrid vehicle control ECU detect that the high-voltage capacitor inside the inverter with converter assembly is not discharged.
The cause of this malfunction may be one of the following:
Inverter voltage sensor (VH) internal circuit malfunction- Voltage sensor (VH) malfunction
- Motor generator control ECU (MG ECU) malfunction
- Communication (wire harness) malfunction
- Inverter with converter assembly malfunction
- Hybrid vehicle control ECU malfunction
- Wire harness malfunction
- Inverter with converter assembly malfunction
DESCRIPTION
For a description of the inverter.
Click here ![]()
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
P0C7600 |
Hybrid/EV Battery System Discharge Time Too Long |
The inverter voltage (VH) does not drop during discharge. (Discharge: Offsetting of the residual pressure in the high-voltage side after power switch is turned off) (1 trip detection logic) |
|
Does not come on |
Master Warning Light: Comes on |
HINT:
When the power switch is turned from on (READY) to off, the MG ECU discharges voltage stored in the inverter by allowing current to flow to motor (MG2) without generating torque. When the vehicle is normal, VH voltage becomes approximately 0 V after discharging. If VH voltage exceeds a specified value, this DTC is stored.
Related Data List DTC No. | Data List |
|---|---|
P0C7600 |
VH-Voltage after Boosting |
CONFIRMATION DRIVING PATTERN
HINT:
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here ![]()
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG) and turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the power switch off and wait for 2 minutes or more.
- Turn the power switch on (READY) and wait for 30 seconds or more.
- Turn the power switch off and wait for 2 minutes or more.
- Turn the power switch on (IG) and turn the Techstream on.
- Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
- Check the DTC judgment result.
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.
WIRING DIAGRAM
Refer to the wiring diagram for the shut down signal circuit.
Click here ![]()
CAUTION:
- Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.
- Inspecting the high-voltage system
- Disconnecting the low voltage connector of the inverter with converter assembly
- Disconnecting the low voltage connector of the HV battery
- To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

- After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

- After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.
Click here

HINT:
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
*a
Without waiting for 10 minutes
NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here ![]()
PROCEDURE
CHECK DTC OUTPUT (HYBRID CONTROL, MOTOR GENERATOR)
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Enter the following menus: Powertrain / Hybrid Control and Motor Generator / Trouble Codes.
(d) Check for DTCs.
Powertrain > Hybrid Control > Trouble Codes Powertrain > Motor Generator > Trouble CodesResult | Proceed to |
|---|---|
P0C7600 only is output, or DTCs except the ones in the table below are also output. |
A |
DTCs of hybrid control system in the tables below are output. |
B |
DTCs of motor generator control system in the tables below are output. |
C |
Malfunction Content | System | Relevant DTC |
|
|---|---|---|---|
Microcomputer malfunction |
Hybrid control system |
P060647 |
Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure |
P060687 |
Hybrid/EV Powertrain Control Module Processor to Monitoring Processor Missing Message |
||
P060A47 |
Hybrid/EV Powertrain Control Module Monitoring Processor Watchdog / Safety MCU Failure |
||
P060A87 |
Hybrid/EV Powertrain Control Module Processor from Monitoring Processor Missing Message |
||
P0A1B49 |
Drive Motor "A" Control Module Internal Electronic Failure |
||
P1C9E9F |
Hybrid/EV System Reset Stuck Off |
||
Motor generator control system |
P0A1B1F |
Generator Control Module Circuit Intermittent |
|
P0A1A47 |
Generator Control Module Watchdog / Safety μC Failure |
||
P0A1A49 |
Generator Control Module Internal Electronic Failure |
||
P1C2A1C |
Generator A/D Converter Circuit Circuit Voltage Out of Range |
||
P1C2A49 |
Generator A/D Converter Circuit Internal Electronic Failure |
||
P1C2B1C |
Drive Motor "A" Control Module A/D Converter Circuit Voltage Out of Range |
||
P1C2B49 |
Drive Motor "A" Control Module A/D Converter Circuit Internal Electronic Failure |
||
P1CAC49 |
Generator Position Sensor Internal Electronic Failure |
||
P1CAD49 |
Drive Motor "A" Position Sensor Internal Electronic Failure |
||
P1CAF38 |
Generator Position Sensor REF Signal Cycle Malfunction Signal Frequency Incorrect |
||
P1CB038 |
Drive Motor "A" Position Sensor REF Signal Frequency Incorrect |
||
P313383 |
Communication Error from Generator to Drive Motor "A" Value of Signal Protection Calculation Incorrect |
||
P313386 |
Communication Error from Generator to Drive Motor "A" Signal Invalid |
||
P313387 |
Communication Error from Generator to Drive Motor "A" Missing Message |
||
Power source circuit malfunction |
Motor generator control system |
P06D61C |
Generator Control Module Offset Power Circuit Voltage Out of Range |
P06B01C |
Generator Control Module Position Sensor REF Power Source Circuit Voltage Out of Range |
||
Communication system malfunction |
Hybrid control system |
P312387 |
Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message |
Sensor and actuator circuit malfunction |
Hybrid control system |
P0AD911 |
Hybrid/EV Battery Positive Contactor Circuit Short to Ground |
P0AD915 |
Hybrid/EV Battery Positive Contactor Circuit Short to Auxiliary Battery or Open |
||
P0ADD11 |
Hybrid/EV Battery Negative Contactor Circuit Short to Ground |
||
P0ADD15 |
Hybrid/EV Battery Negative Contactor Circuit Short to Auxiliary Battery or Open |
||
P0AE411 |
Hybrid/EV Battery Precharge Contactor Circuit Short to Ground |
||
P0AE415 |
Hybrid/EV Battery Precharge Contactor Circuit Short to Auxiliary Battery or Open |
||
Motor generator control system |
P0A3F16 |
Drive Motor "A" Position Sensor Circuit Voltage Below Threshold |
|
P0A4B16 |
Generator Position Sensor Circuit Voltage Below Threshold |
||
P0A4B21 |
Generator Position Sensor Signal Amplitude < Minimum |
||
P0A4B22 |
Generator Position Sensor Signal Amplitude > Maximum |
||
P0C5013 |
Drive Motor "A" Position Sensor Circuit "A" Circuit Open |
||
P0C5016 |
Drive Motor "A" Position Sensor Circuit "A" Circuit Voltage Below Threshold |
||
P0C5017 |
Drive Motor "A" Position Sensor Circuit "A" Circuit Voltage Above Threshold |
||
P0C5A13 |
Drive Motor "A" Position Sensor Circuit "B" Circuit Open |
||
P0C5A16 |
Drive Motor "A" Position Sensor Circuit "B" Circuit Voltage Below Threshold |
||
P0C5A17 |
Drive Motor "A" Position Sensor Circuit "B" Circuit Voltage Above Threshold |
||
P0C6413 |
Generator Position Sensor Circuit "A" Circuit Open |
||
P0C6416 |
Generator Position Sensor Circuit "A" Circuit Voltage Below Threshold |
||
P0C6417 |
Generator Position Sensor Circuit "A" Circuit Voltage Above Threshold |
||
P0C6913 |
Generator Position Sensor Circuit "B" Circuit Open |
||
P0C6916 |
Generator Position Sensor Circuit "B" Circuit Voltage Below Threshold |
||
P0C6917 |
Generator Position Sensor Circuit "B" Circuit Voltage Above Threshold |
||
System malfunction |
Hybrid control system |
P0D2D1C |
Drive Motor "A" Inverter Voltage Sensor Voltage Out of Range |
P1C8349 |
High Voltage Power Resource Circuit Voltage Sensor after Boosting Malfunction |
||
Motor generator control system |
P0D2D16 |
Drive Motor "A" Inverter Voltage Sensor (VH) Circuit Voltage Below Threshold |
|
P0D2D17 |
Drive Motor "A" Inverter Voltage Sensor (VH) Circuit Voltage Above Threshold |
||
P1CB69E |
Drive Motor "A" Inverter Voltage Sensor (VH) Stuck On |
||
HINT:
- P0C7600 may be output as a result of the malfunction indicated by the DTCs above.
- The chart above is listed in inspection order of priority.
- Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)
(e) Turn the power switch off.
| B | GO TO DTC CHART (HYBRID CONTROL SYSTEM) |
| C | GO TO DTC CHART (MOTOR GENERATOR CONTROL SYSTEM) |
|
CHECK SHUT DOWN SIGNAL CIRCUIT
Click here ![]()
HINT:
If the "Shut Down Signal Circuit" inspection results are normal, perform the next step.
| NEXT | REPLACE INVERTER WITH CONVERTER ASSEMBLY |



