Knock Sensor 1 Bank 1 or Single Sensor Circuit Short to Ground (P032511,P033011). Knock Sensor 1 Bank 1 or Single Sensor Circuit Short to Battery or Open (P032515,P033015). Crankshaft Position Sensor
Knock Sensor 1 Bank 1 or Single Sensor Circuit Short to Ground (P032511,P033011)
DESCRIPTION
A flat-type knock control sensor (non-resonant type) has a structure that can detect vibrations between approximately 5 kHz and 15 kHz.
The knock control sensor is fitted onto the engine block to detect engine knocking.
The knock control sensor contains a piezoelectric element which generates a voltage when it becomes deformed.
The voltage is generated when the engine block vibrates due to knocking. Any occurrence of engine knocking can be suppressed by delaying the ignition timing.
HINT:
When DTC P032511 is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is delayed to its maximum retardation. Fail-safe mode continues until the engine switch is turned off.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
P032511 |
Knock Sensor 1 Bank 1 or Single Sensor Circuit Short to Ground |
The knock control sensor (bank 1) output voltage is less than 0.5 V for 1 second or more (1 trip detection logic). |
|
Comes on |
DTC stored |
SAE Code: P0327 |
P033011 |
Knock Sensor 2 Bank 2 Circuit Short to Ground |
The knock control sensor (bank 2) output voltage is less than 0.5 V for 1 second or more (1 trip detection logic). |
|
Comes on |
DTC stored |
SAE Code: P0332 |
Reference: Inspection using an oscilloscope
HINT:
The correct waveform is as shown.
ECM Terminal Name |
Between KNK1 and EKNK Between KNK2 and EKN2 |
Tester Range |
1 V/DIV., 1 ms./DIV. |
Condition |
Engine speed maintained at 4000 rpm after warming up engine |
MONITOR DESCRIPTION
If the output voltage transmitted by the knock control sensor remains low for 1 second or more, the ECM interprets this as a malfunction in the sensor circuit, and stores this DTC.
MONITOR STRATEGY
Related DTCs |
P0327: Knock control sensor (bank 1) range check (low voltage) P0332: Knock control sensor (bank 2) range check (low voltage) |
Required Sensors/Components (Main) |
Knock control sensor |
Required Sensors/Components (Related) |
- |
Frequency of Operation |
Continuous |
Duration |
1 second |
MIL Operation |
Immediate |
Sequence of Operation |
None |
TYPICAL ENABLING CONDITIONS
Monitor runs whenever the following DTCs are not stored |
None |
Both of the following conditions are met |
- |
Battery voltage |
10.5 V or higher |
Time after engine start |
5 seconds or more |
TYPICAL MALFUNCTION THRESHOLDS
Knock control sensor voltage |
Less than 0.5 V |
CONFIRMATION DRIVING PATTERN
HINT:
- After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here

- When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here

- Connect the Techstream to the DLC3.
- Turn the engine switch on (IG).
- Turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the engine switch off and wait for at least 30 seconds.
- Start the engine and wait 5 minutes [A].
- Turn the Techstream on.
- Enter the following menus: Powertrain / Engine / Trouble Codes [B].
- Read the pending DTCs.
HINT:
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
- Enter the following menus: Powertrain / Engine / Utility / All Readiness.
- Input the DTC: P032511 or P033011.
- Check the DTC judgment result.
Techstream Display
Description
NORMAL
- DTC judgment completed
- System normal
ABNORMAL
- DTC judgment completed
- System abnormal
INCOMPLETE
- DTC judgment not completed
- Perform driving pattern after confirming DTC enabling conditions
HINT:
- If the judgment result is NORMAL, the system is normal.
- If the judgment result is ABNORMAL, the system is malfunctioning.
- If the judgment result is INCOMPLETE, idle the engine for 5 minutes and check the DTC judgment result again.
- [A] to [B]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- When clearing the permanent DTCs, do not disconnect the cable from the battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.
WIRING DIAGRAM
HINT:
- DTC P032511 is for the bank 1 knock control sensor circuit.
- DTC P033011 is for the bank 2 knock control sensor circuit.
- Bank 1 refers to the bank that includes the No. 1 cylinder*.
*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.
- Bank 2 refers to the bank that does not include the No. 1 cylinder.
- Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
CHECK TERMINAL VOLTAGE (POWER SOURCE OF KNOCK CONTROL SENSOR)
*a |
Front view of wire harness connector (to Knock Control Sensor) |
*b |
Bank 1 |
*c |
Bank 2 |
(a) Disconnect the knock control sensor connector.
(b) Turn the engine switch on (IG).
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
U6-1 (EKNK) - U6-2 (KNK1) |
Engine switch on (IG) |
4.5 to 5.5 V |
U7-1 (EKN2) - U7-2 (KNK2) |
Engine switch on (IG) |
4.5 to 5.5 V |
| NG | GO TO STEP 3 |
|
INSPECT KNOCK CONTROL SENSOR
(a) Inspect the knock control sensor.
Click here ![]()
HINT:
Perform "Inspection After Repair" after replacing the knock control sensor.
Click here ![]()
| OK | GO TO STEP 4 |
| NG | REPLACE KNOCK CONTROL SENSOR |
CHECK HARNESS AND CONNECTOR (KNOCK CONTROL SENSOR - ECM)
(a) Disconnect the knock control sensor connector.
(b) Disconnect the ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
U6-2 (KNK1) or C56-82 (KNK1) - Body ground |
Always |
10 kΩ or higher |
U7-2 (KNK2) or C56-114 (KNK2) - Body ground |
Always |
10 kΩ or higher |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
CLEAR DTC
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Clear the DTC.
Powertrain > Engine > Clear DTCs(e) Turn the engine switch off and wait for at least 30 seconds.
|
CHECK WHETHER DTC OUTPUT RECURS (DTC P032511 OR P033011)
(a) Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
(b) Enter the following menus: Powertrain / Engine / Trouble Codes.
(c) Read the DTCs.
Powertrain > Engine > Trouble CodesResult | Proceed to |
|---|---|
DTCs are not output |
A |
DTC P032511 or P033011 is output |
B |
| A | CHECK FOR INTERMITTENT PROBLEMS |
| B | REPLACE ECM |
Knock Sensor 1 Bank 1 or Single Sensor Circuit Short to Battery or Open (P032515,P033015)
DESCRIPTION
Refer to DTC P032511.
Click here ![]()
HINT:
When DTC P032515 or P033015 is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is delayed to its maximum retardation. Fail-safe mode continues until the engine switch is turned off.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
P032515 |
Knock Sensor 1 Bank 1 or Single Sensor Circuit Short to Battery or Open |
The knock control sensor (bank 1) output voltage is higher than 4.5 V for 1 second or more (1 trip detection logic). |
|
Comes on |
DTC stored |
SAE Code: P0328 |
P033015 |
Knock Sensor 2 Bank 2 Circuit Short to Battery or Open |
The knock control sensor (bank 2) output voltage is higher than 4.5 V for 1 second or more (1 trip detection logic). |
|
Comes on |
DTC stored |
SAE Code: P0333 |
Reference: Inspection using an oscilloscope.
Click here ![]()
MONITOR DESCRIPTION
If the output voltage transmitted by the knock control sensor remains high for 1 second or more, the ECM interprets this as a malfunction in the sensor circuit, and stores this DTC.
MONITOR STRATEGY
Related DTCs |
P0328: Knock control sensor (bank 1) range check (high voltage) P0333: Knock control sensor (bank 2) range check (high voltage) |
Required Sensors/Components (Main) |
Knock control sensor |
Required Sensors/Components (Related) |
- |
Frequency of Operation |
Continuous |
Duration |
1 second |
MIL Operation |
Immediate |
Sequence of Operation |
None |
TYPICAL ENABLING CONDITIONS
Monitor runs whenever the following DTCs are not stored |
None |
Both of the following conditions are met |
- |
Battery voltage |
10.5 V or higher |
Time after engine start |
5 seconds or more |
TYPICAL MALFUNCTION THRESHOLDS
Knock control sensor voltage |
Higher than 4.5 V |
CONFIRMATION DRIVING PATTERN
HINT:
- After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here

- When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here

- Connect the Techstream to the DLC3.
- Turn the engine switch on (IG).
- Turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the engine switch off and wait for at least 30 seconds.
- Start the engine and wait 5 minutes [A].
- Turn the Techstream on.
- Enter the following menus: Powertrain / Engine / Trouble Codes [B].
- Read the pending DTCs.
HINT:
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
- Enter the following menus: Powertrain / Engine / Utility / All Readiness.
- Input the DTC: P032515 or P033015.
- Check the DTC judgment result.
Techstream Display
Description
NORMAL
- DTC judgment completed
- System normal
ABNORMAL
- DTC judgment completed
- System abnormal
INCOMPLETE
- DTC judgment not completed
- Perform driving pattern after confirming DTC enabling conditions
HINT:
- If the judgment result is NORMAL, the system is normal.
- If the judgment result is ABNORMAL, the system is malfunctioning.
- If the judgment result is INCOMPLETE, idle the engine for 5 minutes and check the DTC judgment result again.
- [A] to [B]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- When clearing the permanent DTCs, do not disconnect the cable from the battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.
WIRING DIAGRAM
Refer to DTC P032511.
Click here ![]()
HINT:
- DTC P032515 is for the bank 1 knock control sensor circuit.
- DTC P033015 is for the bank 2 knock control sensor circuit.
- Bank 1 refers to the bank that includes the No. 1 cylinder*.
*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.
- Bank 2 refers to the bank that does not include the No. 1 cylinder.
- Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
CHECK TERMINAL VOLTAGE (POWER SOURCE OF KNOCK CONTROL SENSOR)
*a |
Front view of wire harness connector (to Knock Control Sensor) |
*b |
Bank 1 |
*c |
Bank 2 |
(a) Disconnect the knock control sensor connector.
(b) Turn the engine switch on (IG).
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
U6-1 (EKNK) - U6-2 (KNK1) |
Engine switch on (IG) |
4.5 to 5.5 V |
U7-1 (EKN2) - U7-2 (KNK2) |
Engine switch on (IG) |
4.5 to 5.5 V |
| NG | GO TO STEP 3 |
|
INSPECT KNOCK CONTROL SENSOR
(a) Inspect the knock control sensor.
Click here ![]()
HINT:
Perform "Inspection After Repair" after replacing the knock control sensor.
Click here ![]()
| OK | GO TO STEP 4 |
| NG | REPLACE KNOCK CONTROL SENSOR |
CHECK HARNESS AND CONNECTOR (KNOCK CONTROL SENSOR - ECM)
(a) Disconnect the knock control sensor connector.
(b) Disconnect the ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
U6-2 (KNK1) - C56-82 (KNK1) |
Always |
Below 1 Ω |
U6-1 (EKNK) - C56-81 (EKNK) |
Always |
Below 1 Ω |
U7-2 (KNK2) - C56-114 (KNK2) |
Always |
Below 1 Ω |
U7-1 (EKN2) - C56-113 (EKN2) |
Always |
Below 1 Ω |
U6-2 (KNK1) or C56-82 (KNK1) - Other terminals |
Always |
10 kΩ or higher |
U7-2 (KNK2) or C56-114 (KNK2) - Other terminals |
Always |
10 kΩ or higher |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
CLEAR DTC
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Clear the DTC.
Powertrain > Engine > Clear DTCs(e) Turn the engine switch off and wait for at least 30 seconds.
|
CHECK WHETHER DTC OUTPUT RECURS (DTC P032515 OR P033015)
(a) Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
(b) Enter the following menus: Powertrain / Engine / Trouble Codes.
(c) Read the DTCs.
Powertrain > Engine > Trouble CodesResult | Proceed to |
|---|---|
DTCs are not output |
A |
DTC P032515 or P033015 is output |
B |
| A | CHECK FOR INTERMITTENT PROBLEMS |
| B | REPLACE ECM |
Crankshaft Position Sensor "A" Circuit Short to Ground (P033511,P033515)
DESCRIPTION
The crankshaft position sensor system consists of a No. 1 crankshaft position sensor plate and Magneto Resistance Element (MRE) type sensor. The crankshaft position sensor plate has 34 teeth at 10° intervals (2 teeth are missing for detecting top dead center), and is installed on the crankshaft. The crankshaft position sensor generates 34 signals per crankshaft revolution. The ECM uses the crankshaft position sensor signal (NE signal) to detect the crankshaft position and engine speed.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
P033511 |
Crankshaft Position Sensor "A" Circuit Short to Ground |
The crankshaft position sensor output voltage is less than 0.3 V for 4 seconds or more (1 trip detection logic). |
|
Comes on |
DTC stored |
SAE Code: P0337 |
P033515 |
Crankshaft Position Sensor "A" Circuit Short to Battery or Open |
The crankshaft position sensor output voltage is higher than 4.7 V for 4 seconds or more (1 trip detection logic). |
|
Comes on |
DTC stored |
SAE Code: P0338 |
- Reference: Inspection using an oscilloscope.
HINT:
The correct waveform is as shown.
ECM Terminal Name
Between NE+ and NE-
Tester Range
2 V/DIV., 20 ms./DIV.
Condition
Idling with warm engine
MONITOR DESCRIPTION
If the output voltage transmitted by the crankshaft position sensor remains low or high, the ECM interprets this as a malfunction in the sensor circuit, illuminates the MIL and stores a DTC.
MONITOR STRATEGY
Related DTCs |
P0337: Crankshaft position sensor range check (Low voltage) P0338: Crankshaft position sensor range check (High voltage) |
Required Sensors/Components (Main) |
Crankshaft position sensor |
Required Sensors/Components (Related) |
VVT sensor |
Frequency of Operation |
Continuous |
Duration |
4 seconds |
MIL Operation |
Immediate |
Sequence of Operation |
None |
TYPICAL ENABLING CONDITIONS
Monitor runs whenever following DTCs are not present |
None |
All of the following conditions are met |
- |
Battery voltage |
8 V or higher |
Engine switch |
On (IG) |
Starter |
Off |
TYPICAL MALFUNCTION THRESHOLDS
P0337: Range Check (Low Voltage)Crankshaft position sensor voltage |
Less than 0.3 V |
Crankshaft position sensor voltage |
Higher than 4.7 V |
CONFIRMATION DRIVING PATTERN
HINT:
- After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here

- When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here

- Connect the Techstream to the DLC3.
- Turn the engine switch on (IG).
- Turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the engine switch off and wait for at least 30 seconds.
- Turn the engine switch on (IG) [A].
- Turn the Techstream on.
- Wait 5 seconds or more [B].
- Enter the following menus: Powertrain / Engine / Trouble Codes [C].
- Read the pending DTCs.
HINT:
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
- Enter the following menus: Powertrain / Engine / Utility / All Readiness.
- Input the DTC: P033511 or P033515.
- Check the DTC judgment result.
Techstream Display
Description
NORMAL
- DTC judgment completed
- System normal
ABNORMAL
- DTC judgment completed
- System abnormal
INCOMPLETE
- DTC judgment not completed
- Perform driving pattern after confirming DTC enabling conditions
HINT:
- If the judgment result is NORMAL, the system is normal.
- If the judgment result is ABNORMAL, the system has a malfunction.
- [A] to [C]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- When clearing the permanent DTCs, do not disconnect the cable from the battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.
WIRING DIAGRAM
HINT:
- The engine speed can be checked by using the Techstream. To perform the check, follow the procedures below:
- Connect the Techstream to the DLC3.
- Turn the engine switch on (IG).
- Turn the Techstream on.
- Enter the following menus: Powertrain / Engine / Data List / Engine Speed.
- Start the engine.
- The engine speed may be indicated as zero despite the engine running normally. This is caused by a lack of NE signals from the crankshaft position sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the crankshaft position sensor output voltage is insufficient.
- Read Freeze Frame Data using the Techstream. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
READ VALUE USING TECHSTREAM (ENGINE SPEED)
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine / Data List / Engine Speed.
Powertrain > Engine > Data ListEngine Speed
(e) Start the engine.
(f) Read the values displayed on the Techstream while the engine is running.
Standard:
Correct values are displayed.
HINT:
- To check the engine speed change, display the graph on the Techstream.
- If the engine does not start, check the engine speed while cranking.
- If the engine speed indicated on the Techstream remains at zero (0), there may be an open or short in the crankshaft position sensor circuit.
| OK | CHECK FOR INTERMITTENT PROBLEMS |
|
CHECK HARNESS AND CONNECTOR
*a |
Front view of wire harness connector (to Crankshaft Position Sensor) |
HINT:
Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.
(a) Disconnect the crankshaft position sensor connector.
(b) Turn the engine switch on (IG).
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
U5-3 (VC) - Body ground |
Engine switch on (IG) |
4.5 to 5.5 V |
U5-1 (NE+) - Body ground |
Engine switch on (IG) |
3.0 to 5.0 V |
(d) Turn the engine switch off and wait for at least 30 seconds.
(e) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
U5-3 (VC) - U5-1 (NE+) |
Engine switch off |
1.425 to 1.575 kΩ |
U5-2 (NE-) - Body ground |
Always |
Below 1 Ω |
| OK | REPLACE CRANK POSITION SENSOR |
|
CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
(a) Disconnect the crankshaft position sensor connector.
(b) Disconnect the ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
U5-3 (VC) - C56-96 (VCNE) |
Always |
Below 1 Ω |
U5-2 (NE-) - C56-95 (NE-) |
Always |
Below 1 Ω |
U5-1 (NE+) - C56-128 (NE+) |
Always |
Below 1 Ω |
U5-3 (VC) or C56-96 (VCNE) - Body ground and other terminals |
Always |
10 kΩ or higher |
U5-2 (NE-) or C56-95 (NE-) - Body ground and other terminals |
Always |
10 kΩ or higher |
U5-1 (NE+) or C56-128 (NE+) - Body ground and other terminals |
Always |
10 kΩ or higher |
| OK | REPLACE ECM |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |