Motor/Generator Shutdown Signal Stuck Off (P321E9F). ECM/PCM Power Relay Sense Circuit Intermittent (P06881F). Hybrid/EV Battery Control System Over Temperature (P30004B)
Motor/Generator Shutdown Signal Stuck Off (P321E9F)
DTC SUMMARY
MALFUNCTION DESCRIPTION
The hybrid vehicle control ECU detects malfunctions which prevent the inverter with converter assembly emergency shutdown circuit (HSDN) from shutting down the hybrid control system. Detection is performed when the power switch is turned on (IG) and during the shutdown sequence when the power switch is turned off.
The cause of this malfunction may be one of the following:
Hybrid vehicle control ECU and inverter with converter assembly shutdown circuit malfunction- Hybrid vehicle control ECU malfunction
- Connector or wire harness malfunction (between hybrid vehicle control ECU and inverter with converter assembly) malfunction
- Inverter with converter assembly malfunction
DESCRIPTION
The hybrid vehicle control ECU sends a block signal to the motor generator control ECU (MG ECU) to shutdown the power supply to the motor. When the system is not in the on (READY) state, it sends an HSDN (MG shutdown signal) signal from the hybrid vehicle control ECU to the motor generator control ECU (MG ECU) to check the function of the HV gate block. When a malfunction is detected in the HV gate block function, DTCs are stored.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
P321E9F |
Motor/Generator Shutdown Signal Stuck Off |
When the HV gate block function check is performed (when the power switch is turned from on (READY) to off), the inverter voltage (VH) drops and current flows in the inverter. (1 trip detection logic) |
|
Does not come on |
Master Warning Light: Comes on |
DTC No. | Data List |
|---|---|
P321E9F |
|
CONFIRMATION DRIVING PATTERN
HINT:
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here ![]()
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG) and turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the power switch off and wait for 2 minutes or more.
- Turn the power switch on (READY) and wait for 30 seconds or more.
- Turn the power switch off and wait for 2 minutes or more.
- Turn the power switch on (READY) and wait for 30 seconds or more.
- Turn the power switch off and wait for 2 minutes or more.
- Turn the power switch on (IG) and turn the Techstream on.
- Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
- Check the DTC judgment result.
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.
WIRING DIAGRAM
Refer to the wiring diagram for the shut down signal circuit.
Click here ![]()
CAUTION:
- Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.
- Inspecting the high-voltage system
- Disconnecting the low voltage connector of the inverter with converter assembly
- Disconnecting the low voltage connector of the HV battery
- To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

- After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

- After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.
Click here

HINT:
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
*a
Without waiting for 10 minutes
NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here ![]()
PROCEDURE
CHECK DTC OUTPUT (HYBRID CONTROL)
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
(d) Check for DTCs.
Powertrain > Hybrid Control > Trouble CodesResult | Proceed to |
|---|---|
P321E9F only is output, or DTCs except the ones in the table below are also output |
A |
Any of the following DTCs are also output |
B |
Malfunction Content | Relevant DTC |
|
|---|---|---|
Sensor and actuator circuit malfunction |
P33B99F |
Motor/Generator Shutdown Signal (Hybrid/EV Side) Stuck Off |
P33BF9F |
Motor/Generator Shutdown Signal (MG Side) Stuck Off |
|
HINT:
- P321E9F may be output as a result of the malfunction indicated by the DTCs above.
- The chart above is listed in inspection order of priority.
- Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)
(e) Turn the power switch off.
| B | GO TO DTC CHART (HYBRID CONTROL SYSTEM) |
|
CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)
Click here ![]()
| NG | CONNECT SECURELY |
|
CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)
Click here ![]()
Result | Proceed to |
|---|---|
OK |
A |
NG (The connector is not connected securely.) |
B |
NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) |
C |
| B | CONNECT SECURELY |
| C | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - HYBRID VEHICLE CONTROL ECU)
CAUTION:
Be sure to wear insulated gloves.
(a) Check that the service plug grip is not installed.
NOTICE:
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
(b) Disconnect the A42 inverter with converter assembly connector.
(c) Disconnect the A24 hybrid vehicle control ECU connector.
(d) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
(e) Reconnect the A24 hybrid vehicle control ECU connector.
(f) Reconnect the A42 inverter with converter assembly connector.
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
CHECK INVERTER WITH CONVERTER ASSEMBLY
CAUTION:
Be sure to wear insulated gloves.
(a) Check that the service plug grip is not installed.
NOTICE:
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
(b) Disconnect the A42 inverter with converter assembly connector.
(c) Measure the resistance according to the value(s) in the table below. Standard Resistance:
NOTICE: Be sure not to damage or deform the terminal being inspected. |
|
(d) Reconnect the A42 inverter with converter assembly connector.
| OK | REPLACE HYBRID VEHICLE CONTROL ECU |
| NG | REPLACE INVERTER WITH CONVERTER ASSEMBLY |
ECM/PCM Power Relay Sense Circuit Intermittent (P06881F)
DESCRIPTION
This DTC indicates that the hybrid vehicle control ECU detected an instantaneous interruption in +B power source voltage.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
P06881F |
ECM/PCM Power Relay Sense Circuit Intermittent |
When the power switch is on (READY), the hybrid vehicle control ECU is reset due to an instantaneous interruption of power source. (1 trip detection logic) |
|
Does not come on |
Master Warning Light: Comes on |
CONFIRMATION DRIVING PATTERN
HINT:
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here ![]()
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG) and turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the power switch off and wait for 2 minutes or more.
- Turn the power switch on (IG) and turn the Techstream on.
- Turn the power switch on (READY) and wait for 30 seconds or more.
(If the DTC is not output, drive the vehicle on urban roads according to the freeze frame data item "Vehicle Speed" for approximately 5 minutes.)
- Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
- Check the DTC judgment result.
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.
WIRING DIAGRAM
PROCEDURE
CHECK AUXILIARY BATTERY TERMINAL
(a) Confirm whether the auxiliary battery terminals have been disconnected recently.
Result | Proceed to |
|---|---|
Terminals have been disconnected. |
A |
Terminals have not been disconnected. |
B |
| B | GO TO STEP 5 |
|
CONFIRM MASTER WARNING LIGHT
(a) Turn the power switch on (READY) from off.
(b) Confirm that the master warning light illuminates.
| Result | Proceed to |
|---|---|
Master warning light illuminates. |
A |
Master warning light does not illuminate. |
B |
NOTICE:
DTC P06881F may be stored after disconnecting and reconnecting the auxiliary battery terminals. If this happens, the DTC will not be output if the power switch is turned off and then on (READY) again. In this case, clear the DTCs to complete the inspection.
(c) Turn the power switch off.
| B | END |
|
CLEAR DTC
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
(d) Read and record the DTCs and freeze frame data.
Powertrain > Hybrid Control > Trouble Codes(e) Clear the DTCs and freeze frame data.
Powertrain > Hybrid Control > Clear DTCs(f) Turn the power switch off and wait for 2 minutes or more.
|
CHECK DTC OUTPUT (HYBRID CONTROL)
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
(d) Check for DTCs.
Powertrain > Hybrid Control > Trouble Codes| Result | Proceed to |
|---|---|
DTC P06881F is output again. |
A |
DTCs other than P06881F are also output. |
B |
(e) Turn the power switch off.
| B | GO TO DTC CHART (HYBRID CONTROL SYSTEM) |
|
CHECK AUXILIARY BATTERY TERMINAL (CONTACT PROBLEM)
(a) Check the connection of the auxiliary battery terminal.
OK:
The terminal is connected securely and there is no contact problem.
| NG | CONNECT SECURELY |
|
CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)
Click here ![]()
| NG | CONNECT SECURELY |
|
CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - IGCT RELAY)
(a) Remove the IGCT relay from the No. 3 relay block.
(b) Disconnect the A23 and A24 hybrid vehicle control ECU connectors.
(c) Measure the resistance according to the value(s) in the table below.
*1 |
No. 3 Relay Block |
*2 |
IGCT Relay Holder |
*a |
Rear view of wire harness connector (to Hybrid Vehicle Control ECU) |
- |
- |
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
A24-4 (+B1) - 5 (IGCT relay holder) |
Power switch off |
Below 1 Ω |
A23-1 (+B2) - 5 (IGCT relay holder) |
Power switch off |
Below 1 Ω |
(d) Reconnect the A23 and A24 hybrid vehicle control ECU connectors.
(e) Reinstall the IGCT relay.
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
CHECK FOR INTERMITTENT PROBLEMS
(a) Check for intermittent problems.
Click here ![]()
(1) Check the connection and terminal contact pressure of the connectors and wire harnesses between the hybrid vehicle control ECU and the No. 3 relay block.
(2) When the power switch is on (READY), jiggle the connectors and wire harnesses between the hybrid vehicle control ECU and the No. 3 relay block.
| Result | Proceed to |
|---|---|
Problem symptom does not recur. |
A |
Problem symptom recurs. |
B |
| A | REPLACE HYBRID VEHICLE CONTROL ECU |
| B | REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA |
Hybrid/EV Battery Control System Over Temperature (P30004B)
DESCRIPTION
The hybrid vehicle control ECU monitors its internal operation and detects the following malfunction.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
P30004B |
Hybrid/EV Battery Control System Over Temperature |
The HV battery temperature becomes too high due to a malfunction in the HV system. (1 trip detection logic) |
|
Does not come on |
Master Warning Light: Comes on |
DTC No. | Data List |
|---|---|
P30004B |
|
CONFIRMATION DRIVING PATTERN
HINT:
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here ![]()
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG) and turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the power switch off and wait for 2 minutes or more.
- Turn the power switch on (IG) and turn the Techstream on.
- Drive the vehicle for approximately 10 minutes according to the freeze frame data items "Vehicle Speed", "Hybrid Battery Temperature 1 to 3", "Hybrid Battery Cooling Fan Intake Air Temperature 1", "Ambient Temperature" and "Hybrid Battery Current".
- Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
- Check the DTC judgment result.
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.
CAUTION:
- Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.
- Inspecting the high-voltage system
- Disconnecting the low voltage connector of the inverter with converter assembly
- Disconnecting the low voltage connector of the HV battery
- To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

- After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

- After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.
*a
Without waiting for 10 minutes
Click here

HINT:
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
- Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.
If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.
- When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.
*a
Dealer
*b
Battery Collection Agent
- Before returning the HV battery, make sure to perform a recovery inspection.
- Make a note of the output DTCs as some of them may be necessary for recovery inspection of the HV battery.
NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here ![]()
PROCEDURE
CHECK DTC OUTPUT (HYBRID CONTROL)
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
(d) Check for DTCs.
Powertrain > Hybrid Control > Trouble CodesResult | Proceed to |
|---|---|
P30004B only is output. |
A |
DTCs other than P30004B are also output. |
B |
(e) Turn the power switch off.
| B | GO TO DTC CHART (HYBRID CONTROL SYSTEM) |
|
CLEAN NO. 1 HV BATTERY INTAKE FILTER
(a) Check the HV battery cooling system intake port for blockage. HINT: If anything is blocking the HV battery cooling system intake port, remove it. |
|
(b) Clean the No. 1 HV battery intake filter.
Click here ![]()
|
CHECK FREEZE FRAME DATA (HYBRID CONTROL)
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
(d) Read the freeze frame data of DTC P30004B.
Powertrain > Hybrid Control > Trouble CodesNOTICE:
Although freeze frame data is recorded before and after a DTC is stored, for this step it is only necessary to read the freeze frame data recorded before "0s" (when the DTC was stored).
*a |
Freeze Frame Data Recorded |
*b |
DTC Stored |
*c |
Time |
Result | Proceed to |
|---|---|
Other than below |
A |
The difference between the value of "VL-Voltage before Boosting" and the total of "Hybrid Battery Block 1 to 11 Voltage" is 10 V or more. |
B |
(e) Turn the power switch off.
| B | GO TO STEP 7 |
|
CHECK FREEZE FRAME DATA (HYBRID CONTROL)
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
(d) Read the freeze frame data of DTC P30004B.
Powertrain > Hybrid Control > Trouble CodesNOTICE:
Although freeze frame data is recorded before and after a DTC is stored, for this step it is only necessary to read the freeze frame data recorded at "0s" (when the DTC was stored).
Result | Proceed to |
|---|---|
Other than below |
A |
The value of any of "Hybrid Battery Temperature 1 to 3" is 80 °C or more. |
B |
(e) Turn the power switch off.
| B | GO TO STEP 8 |
|
READ VALUE USING TECHSTREAM (DATA LIST)
(a) Apply the parking brake and secure the wheels using chocks.
(b) Connect the Techstream to the DLC3.
(c) Turn the power switch on (READY).
(d) Enter the following menus: Powertrain / Hybrid Control / Data List / Hybrid Battery Temperature 1 to 3.
Powertrain > Hybrid Control > Data ListTester Display |
|---|
Hybrid Battery Temperature 1 |
Hybrid Battery Temperature 2 |
Hybrid Battery Temperature 3 |
(e) According to the display on the Techstream, read the Data List and check that the value of each "Hybrid Battery Temperature 1 to 3" is 40 °C or less.
HINT:
If the value of any of "Hybrid Battery Temperature 1 to 3" is more than 40 °C, turn the power switch off and wait until the values to decrease to 40 °C or less before continuing this procedure.
(f) Enter the following menus: Powertrain / Hybrid Control / Data List / Hybrid Battery Block 1, 2, 9, 10, 11 Voltage.
Powertrain > Hybrid Control > Data ListTester Display |
|---|
Hybrid Battery Block 1 Voltage |
Hybrid Battery Block 2 Voltage |
Hybrid Battery Block 9 Voltage |
Hybrid Battery Block 10 Voltage |
Hybrid Battery Block 11 Voltage |
(g) According to the display on the Techstream, read the Data List and check the value of each "Hybrid Battery Block 1, 2, 9, 10 and 11 Voltage" with the power switch on (IG).
*a |
Hybrid Battery Block 1 Voltage |
*b |
Hybrid Battery Block 2 Voltage |
*c |
Hybrid Battery Block 3 Voltage |
*d |
Hybrid Battery Block 4 Voltage |
*e |
Hybrid Battery Block 5 Voltage |
*f |
Hybrid Battery Block 6 Voltage |
*g |
Hybrid Battery Block 7 Voltage |
*h |
Hybrid Battery Block 8 Voltage |
*i |
Hybrid Battery Block 9 Voltage |
*j |
Hybrid Battery Block 10 Voltage |
*k |
Hybrid Battery Block 11 Voltage |
- |
- |
Result | Proceed to |
|---|---|
Other than below |
A |
The difference between the lowest and highest HV Battery Block Voltage is 0.3 V or more. |
B |
(h) Turn the power switch off.
| B | GO TO STEP 8 |
|
READ VALUE USING TECHSTREAM (DATA LIST)
(a) Apply the parking brake and secure the wheels using chocks.
(b) Connect the Techstream to the DLC3.
(c) Turn the power switch on (READY).
(d) Enter the following menus: Powertrain / Hybrid Control / Data List / Hybrid Battery Temperature 1 to 3.
Powertrain > Hybrid Control > Data ListTester Display |
|---|
Hybrid Battery Temperature 1 |
Hybrid Battery Temperature 2 |
Hybrid Battery Temperature 3 |
(e) According to the display on the Techstream, read the Data List and check that the value of each "Hybrid Battery Temperature 1 to 3" is 40 °C or less.
HINT:
If the value of any of "Hybrid Battery Temperature 1 to 3" is more than 40 °C, turn the power switch off and wait until the values to decrease to 40 °C or less before continuing this procedure.
(f) Enter the following menus: Powertrain / Hybrid Control / Data List / Hybrid Battery Block 3 to 8 Voltage.
Powertrain > Hybrid Control > Data ListTester Display |
|---|
Hybrid Battery Block 3 Voltage |
Hybrid Battery Block 4 Voltage |
Hybrid Battery Block 5 Voltage |
Hybrid Battery Block 6 Voltage |
Hybrid Battery Block 7 Voltage |
Hybrid Battery Block 8 Voltage |
(g) According to the display on the Techstream, read the Data List and check the value of each "Hybrid Battery Block 3 to 8 Voltage" with the power switch on (IG).
*a |
Hybrid Battery Block 1 Voltage |
*b |
Hybrid Battery Block 2 Voltage |
*c |
Hybrid Battery Block 3 Voltage |
*d |
Hybrid Battery Block 4 Voltage |
*e |
Hybrid Battery Block 5 Voltage |
*f |
Hybrid Battery Block 6 Voltage |
*g |
Hybrid Battery Block 7 Voltage |
*h |
Hybrid Battery Block 8 Voltage |
*i |
Hybrid Battery Block 9 Voltage |
*j |
Hybrid Battery Block 10 Voltage |
*k |
Hybrid Battery Block 11 Voltage |
- |
- |
Result | Proceed to |
|---|---|
Other than below |
A |
The difference between the lowest and highest HV Battery Block Voltage is 0.3 V or more. |
B |
(h) Turn the power switch off.
| A | END |
| B | GO TO STEP 8 |
REPLACE BATTERY VOLTAGE SENSOR
Click here ![]()
| NEXT | REPLACE HV BATTERY |
REPLACE HYBRID VEHICLE CONTROL ECU
Click here ![]()
| NEXT | REPLACE HV BATTERY |


