Throttle / Pedal Position Sensor / Switch "A" Circuit Voltage Out of Range (P01201C). Camshaft Position "B" - Actuator Bank 1 Circuit Open (P001313). Camshaft Position "B" - Timing Over-Advanced or Sy
Throttle / Pedal Position Sensor / Switch "A" Circuit Voltage Out of Range (P01201C)
DESCRIPTION
Refer to DTC P012011.
Click here ![]()
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
P01201C |
Throttle / Pedal Position Sensor / Switch "A" Circuit Voltage Out of Range |
The difference between the output voltage of VTA1 and VTA2 is less than 0.8 V, or higher than 1.6 V for less than 2 seconds (1 trip detection logic). |
|
Comes on |
DTC stored |
SAE Code: P0121 |
MONITOR DESCRIPTION
The ECM uses the throttle position sensor to monitor the throttle valve opening angle. There are several checks that the ECM performs to confirm the proper operation of the throttle position sensor.
This sensor transmits two signals: VTA1 and VTA2. VTA1 is used to detect the throttle opening angle and VTA2 is used to detect malfunctions in VTA1. The ECM performs several checks to confirm the proper operation of the throttle position sensor and VTA1.
For each throttle opening angle, a specific voltage difference is expected between the outputs of VTA1 and VTA2. If the output voltage difference between the two signals deviates from the normal operating range, the ECM interprets this as a malfunction of the throttle position sensor, illuminates the MIL and stores a DTC.
MONITOR STRATEGY
Related DTCs |
P0121: Throttle position sensor rationality |
Required Sensors/Components (Main) |
Throttle position sensor |
Required Sensors/Components (Related) |
- |
Frequency of Operation |
Continuous |
Duration |
Within 2 seconds |
MIL Operation |
Immediate |
Sequence of Operation |
None |
TYPICAL ENABLING CONDITIONS
Either of the following conditions is met |
A or B |
A. Power switch |
On (IG) |
B. Throttle actuator power |
On |
Throttle position sensor circuit fail (P0122, P0123, P0222, P0223, P2135) |
Not detected |
TYPICAL MALFUNCTION THRESHOLDS
Either of the following conditions is met |
A or B |
A. Difference of learned throttle position sensor opener position voltage between VTA2 and VTA1 |
Higher than 1.6 V |
B. Difference of learned throttle position sensor opener position voltage between VTA2 and VTA1 |
Less than 0.8 V |
CONFIRMATION DRIVING PATTERN
HINT:
- After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here

- When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here

- Connect the Techstream to the DLC3.
- Turn the power switch on (IG).
- Turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the power switch off and wait for at least 30 seconds.
- Turn the power switch on (IG) [A].
- Turn the Techstream on.
- Put the engine in Inspection Mode (Maintenance Mode).
Click here

- Start the engine.
- With the vehicle stationary, fully depress and release the accelerator pedal [B].
HINT:
During charge control, the engine speed is set at idle. Therefore, the engine speed will not increase when the accelerator pedal is depressed. In this case, perform step [B] after charge control has completed.
- Idle the engine for 2 seconds or more [C].
- Enter the following menus: Powertrain / Engine / Trouble Codes [D].
- Read the pending DTCs.
HINT:
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
- Enter the following menus: Powertrain / Engine / Utility / All Readiness.
- Input the DTC: P01201C.
- Check the DTC judgment result.
Techstream Display
Description
NORMAL
- DTC judgment completed
- System normal
ABNORMAL
- DTC judgment completed
- System abnormal
INCOMPLETE
- DTC judgment not completed
- Perform driving pattern after confirming DTC enabling conditions
HINT:
- If the judgment result is NORMAL, the system is normal.
- If the judgment result is ABNORMAL, the system is malfunctioning.
- If the judgment result is INCOMPLETE, perform steps [B] through [D] again.
- [A] to [D]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- When clearing the permanent DTCs, do not disconnect the cable from the auxiliary battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.
FAIL-SAFE
When this DTC is stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 7.5° throttle valve opening angle by the return spring. The ECM then adjusts the engine output, by controlling the fuel injection (intermittent fuel cut) and ignition timing, in accordance with the engine torque request signal sent from the hybrid vehicle control ECU assembly, to allow the vehicle to continue being driven at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.
Fail-safe mode continues until a pass condition is detected, and the power switch is turned off.
WIRING DIAGRAM
Refer to DTC P012011.
Click here ![]()
NOTICE:
- Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the Freeze Frame Data and Vehicle Control History can be useful for troubleshooting.
Click here

(Select Powertrain in Health Check and then check the time stamp data.)
Click here

- If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.
Click here

HINT:
- DTC P01201C is stored when the VTA1 and VTA2 output voltages are not consistent with the sensor characteristics. Therefore, check the Freeze Frame Data for this DTC. Use the following formula to confirm the relative differences in voltage.
Characteristic Sensor Output:
VTA2 x 0.8 is approximately equal to VTA1 + 1.11 V
VTA1: Throttle Position Sensor No.1 Voltage
VTA2: Throttle Position Sensor No.2 Voltage
- Read Freeze Frame Data using the Techstream. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)
(a) Disconnect the throttle body with motor assembly connector.
(b) Disconnect the ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
C25-2 (VC) - C55-109 (VCTA) |
Always |
Below 1 Ω |
C25-1 (VTA) - C55-108 (VTA1) |
Always |
Below 1 Ω |
C25-3 (VTA2) - C55-87 (VTA2) |
Always |
Below 1 Ω |
C25-4 (E2) - C55-110 (ETA) |
Always |
Below 1 Ω |
C25-2 (VC) or C55-109 (VCTA) - Body ground and other terminals |
Always |
10 kΩ or higher |
C25-1 (VTA) or C55-108 (VTA1) - Body ground and other terminals |
Always |
10 kΩ or higher |
C25-3 (VTA2) or C55-87 (VTA2) - Body ground and other terminals |
Always |
10 kΩ or higher |
(d) Inspect the condition of the terminals of the connectors.
Click here ![]()
| OK | GO TO STEP 5 |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
(a) Repair or replace the wire harness or connector.
|
CLEAR DTC
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Clear the DTCs.
Powertrain > Engine > Clear DTCs(e) Turn the power switch off and wait for at least 30 seconds.
|
CHECK WHETHER DTC OUTPUT RECURS (DTC P01201C)
(a) Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
(b) Enter the following menus: Powertrain / Engine / Trouble Codes.
(c) Read the DTCs.
Powertrain > Engine > Trouble CodesResult | Proceed to |
|---|---|
DTCs are not output |
A |
DTC P01201C is output |
B |
| A | END |
|
CHECK HARNESS AND CONNECTOR (RESISTANCE OF ECM)
(a) Disconnect the throttle body with motor assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
C25-2 (VC) - C25-1 (VTA) |
Power switch off |
190 to 210 kΩ |
C25-2 (VC) - C25-3 (VTA2) |
Power switch off |
190 to 210 kΩ |
HINT:
Perform "Inspection After Repair" after replacing the throttle body with motor assembly.
Click here ![]()
| OK | REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY |
| NG | REPLACE ECM |
Camshaft Position "B" - Actuator Bank 1 Circuit Open (P001313)
DESCRIPTION
The Variable Valve Timing (VVT) system (for exhaust side) adjusts the exhaust valve timing to improve driveability. The engine oil pressure turns the VVT controller (camshaft timing exhaust gear assembly) to adjust the valve timing.
The cam timing oil control solenoid assembly operates according to signals received from the ECM to control the position of the camshaft timing oil control valve assembly (exhaust camshaft timing gear bolt assembly) and supply engine oil. The camshaft timing oil control valve assembly (exhaust camshaft timing gear bolt assembly) moves when the ECM applies 12 V to the cam timing oil control solenoid assembly. The ECM changes the energizing time of the cam timing oil control solenoid assembly (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
P001313 |
Camshaft Position "B" - Actuator Bank 1 Circuit Open |
Open or short in cam timing oil control solenoid assembly circuit (1 trip detection logic). |
|
Comes on |
DTC stored |
SAE Code: P0013 |
MONITOR DESCRIPTION
This DTC is designed to detect an open or short in the cam timing oil control solenoid assembly circuit. If the cam timing oil control solenoid assembly duty-cycle is excessively high or low while the power switch is on (IG) or the engine is running, the ECM will illuminate the MIL and store this DTC.
MONITOR STRATEGY
Related DTCs |
P0013: Cam timing oil control solenoid assembly range check |
Required Sensors/Components (Main) |
Cam timing oil control solenoid assembly |
Required Sensors/Components (Related) |
- |
Frequency of Operation |
Continuous |
Duration |
1 second |
MIL Operation |
Immediate |
Sequence of Operation |
None |
TYPICAL ENABLING CONDITIONS
AllMonitor runs whenever the following DTCs are not stored |
None |
All of the following conditions are met |
- |
Auxiliary battery voltage |
8 V or higher |
Power switch |
On (IG) |
Time after power switch off to on (IG) |
0.5 seconds or more |
Either of the following conditions is met |
A or B |
A. Both of the following conditions are met |
- |
Auxiliary battery voltage |
11 V or higher, and less than 13 V |
Target duty cycle |
Less than 70% |
B. Both of the following conditions are met |
- |
Auxiliary battery voltage |
13 V or higher |
Target duty cycle |
Less than 80% |
Both of the following conditions are met |
- |
Current cut status |
Not cut |
Target duty cycle |
25% or higher |
TYPICAL MALFUNCTION THRESHOLDS
Case 1Output duty cycle |
100% or higher |
Output duty cycle |
0% or less |
CONFIRMATION DRIVING PATTERN
HINT:
- After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here

- When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here

- Connect the Techstream to the DLC3.
- Turn the power switch on (IG).
- Turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the power switch off and wait for at least 30 seconds.
- Turn the power switch on (IG).
- Turn the Techstream on.
- Put the engine in Inspection Mode (Maintenance Mode).
Click here

- Start the engine [A].
- Wait 5 seconds or more [B].
- Enter the following menus: Powertrain / Engine / Trouble Codes [C].
- Read the pending DTCs.
HINT:
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
- Enter the following menus: Powertrain / Engine / Utility / All Readiness.
- Input the DTC: P001313.
- Check the DTC judgment result.
Techstream Display
Description
NORMAL
- DTC judgment completed
- System normal
ABNORMAL
- DTC judgment completed
- System abnormal
INCOMPLETE
- DTC judgment not completed
- Perform driving pattern after confirming DTC enabling conditions
HINT:
- If the judgment result is NORMAL, the system is normal.
- If the judgment result is ABNORMAL, the system has a malfunction.
- If the judgment result is INCOMPLETE, perform steps [A] through [C] again.
- [A] to [C]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- When clearing the permanent DTCs, do not disconnect the cable from the auxiliary battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.
WIRING DIAGRAM
NOTICE:
- Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the Freeze Frame Data and Vehicle Control History can be useful for troubleshooting.
Click here

(Select Powertrain in Health Check and then check the time stamp data.)
Click here

- If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.
Click here

HINT:
Read Freeze Frame Data using the Techstream. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
CLEAR DTC
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Clear the DTC after recording the Freeze Frame Data and DTC.
Powertrain > Engine > Clear DTCs(e) Turn the power switch off and wait for at least 30 seconds.
|
READ OUTPUT DTC (DTC P001313)
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Put the engine in Inspection Mode (Maintenance Mode).
Powertrain > Hybrid Control > UtilityInspection Mode
(e) Start the engine.
(f) Enter the following menus: Powertrain / Engine / Trouble Codes.
(g) Read the DTCs.
Powertrain > Engine > Trouble CodesResult | Proceed to |
|---|---|
DTCs are not output |
A |
DTC P001313 is output |
B |
| A | CHECK FOR INTERMITTENT PROBLEMS |
|
INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY
(a) Inspect the cam timing oil control solenoid assembly.
Click here ![]()
| NG | REPLACE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY |
|
CHECK HARNESS AND CONNECTOR (CAM TIMING OIL CONTROL SOLENOID ASSEMBLY - ECM)
(a) Disconnect the cam timing oil control solenoid assembly connector.
(b) Disconnect the ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
C22-2 (+) - C55-26 (OE1+) |
Always |
Below 1 Ω |
C22-1 (-) - C55-25 (OE1-) |
Always |
Below 1 Ω |
C22-2 (+) or C55-26 (OE1+) - Body ground and other terminals |
Always |
10 kΩ or higher |
C22-1 (-) or C55-25 (OE1-) - Body ground and other terminals |
Always |
10 kΩ or higher |
| OK | REPLACE ECM |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
Camshaft Position "B" - Timing Over-Advanced or System Performance Bank 1 (P001400,P001500)
DESCRIPTION
Refer to DTC P001313.
Click here ![]()
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
P001400 |
Camshaft Position "B" - Timing Over-Advanced or System Performance Bank 1 |
Exhaust valve timing is stuck at a certain value when in the advance range (2 trip detection logic). |
|
Comes on |
DTC stored |
SAE Code: P0014 |
P001500 |
Camshaft Position "B" - Timing Over-Retarded Bank 1 |
Exhaust valve timing is stuck at a certain value when in the retard range (1 trip detection logic). |
|
Comes on |
DTC stored |
SAE Code: P0015 |
MONITOR DESCRIPTION
The ECM optimizes the exhaust valve timing using the Variable Valve Timing (VVT) system to control the exhaust camshaft. The VVT system includes the ECM, cam timing oil control solenoid assembly, camshaft timing oil control valve assembly (exhaust camshaft timing gear bolt assembly) and camshaft timing exhaust gear assembly. The ECM sends a target duty-cycle control signal to the cam timing oil control solenoid assembly. The camshaft timing oil control valve assembly (exhaust camshaft timing gear bolt assembly) is operated to control the oil pressure supplied to the camshaft timing exhaust gear assembly based on this signal. The camshaft timing gear assembly can advance or retard the exhaust camshaft.
If the difference between the target and actual exhaust valve timing is large, and changes in the actual exhaust valve timing are small, the ECM interprets this as the camshaft timing exhaust gear assembly stuck malfunction and stores a DTC.
- Example:
- A DTC is stored when the following conditions are met:
- It takes 5 seconds or more to change the valve timing by 5°CA.
- After the above condition is met, the cam timing oil control solenoid assembly is forcibly activated for 9.5 seconds.
These DTCs indicate that the camshaft timing exhaust gear assembly cannot operate properly due to a camshaft timing oil control valve assembly (exhaust camshaft timing gear bolt assembly) malfunction or the presence of foreign matter in the camshaft timing oil control valve assembly (exhaust camshaft timing gear bolt assembly).
MONITOR STRATEGY
Related DTCs |
P0014: Advanced camshaft timing (for exhaust camshaft) P0015: Retarded camshaft timing (for exhaust camshaft) |
Required Sensors/Components (Main) |
Cam timing oil control solenoid assembly Camshaft timing oil control valve assembly (exhaust camshaft timing gear bolt assembly) Camshaft timing exhaust gear assembly |
Required Sensors/Components (Related) |
Crankshaft position sensor Camshaft position sensor Engine coolant temperature sensor |
Frequency of Operation |
Continuous |
Duration |
Within 10 seconds |
MIL Operation |
Advanced camshaft timing: 2 driving cycles Retarded camshaft timing: Immediate |
Sequence of Operation |
None |
TYPICAL ENABLING CONDITIONS
Monitor runs whenever the following DTCs are not stored |
P0013 (Exhaust VVT oil control solenoid) P0017 (Exhaust VVT system - misalignment) P0101, P0102, P0103 (Mass air flow meter) P0107, P0108 (Manifold absolute pressure) P0117, P0118 (Engine coolant temperature sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P0335, P0337, P0338 (Crankshaft position sensor) P0340, P0342, P0343 (Camshaft position sensor) P0365, P0367, P0368 (Exhaust camshaft position sensor) |
Auxiliary battery voltage |
11 V or higher |
Engine speed |
500 to 4000 rpm |
Engine coolant temperature |
75 to 100 °C |
TYPICAL MALFUNCTION THRESHOLDS
P0014: Advanced Camshaft TimingBoth of the following conditions are met |
- |
Deviation of actual valve timing and target valve timing |
More than 5°CA (Crankshaft Angle) for 5 seconds or more after the VVT hold duty ratio learned value reaches the upper or lower limit |
Valve timing |
No change at advanced valve timing |
Both of the following conditions are met |
- |
Deviation of actual valve timing and target valve timing |
More than 5°CA (Crankshaft Angle) for 5 seconds or more after the VVT hold duty ratio learned value reaches the upper or lower limit |
Valve timing |
No change at retarded valve timing |
If the difference between the target and actual camshaft timing is greater than the specified value, the ECM operates the VVT actuator for 10 seconds by applying and releasing oil pressure. Then, the ECM monitors the camshaft timing change for 10 seconds.
MONITOR RESULT
Refer to detailed information in Checking Monitor Status.
Click here ![]()
Monitor ID | Test ID | Scaling | Unit | Description |
|---|---|---|---|---|
$35 |
$85 |
Multiply by 0.01 |
Second |
Forced movement of oil control solenoid time |
CONFIRMATION DRIVING PATTERN
HINT:
- After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here

- When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here

- Connect the Techstream to the DLC3.
- Turn the power switch on (IG).
- Turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
HINT:
- P001400 is output:
Clear the DTC not using the Techstream.
- P001500 is output:
Clear the DTC using the Techstream.
- P001400 is output:
- Turn the power switch off and wait for at least 30 seconds.
- Turn the power switch on (IG) [A].
- Turn the Techstream on.
- Put the engine in Inspection Mode (Maintenance Mode).
Click here

- Start the engine and warm it up until the engine coolant temperature reaches 75 °C or higher [B].
- With the engine running, accelerate the vehicle to 75 km/h or more by depressing the accelerator pedal for 10 seconds or more [C].
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
HINT:
If the engine stops, further depress the accelerator pedal to restart the engine.
- Idle the engine for 100 seconds or more [D].
HINT:
- P001400 is output:
With the shift lever in P.
- P001500 is output:
With the shift lever in D.
- P001400 is output:
- Enter the following menus: Powertrain / Engine / Trouble Codes [E].
- Read the pending DTCs.
HINT:
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
- Enter the following menus: Powertrain / Engine / Utility / All Readiness.
- Input the DTC: P001400 or P001500.
- Check the DTC judgment result.
Techstream Display
Description
NORMAL
- DTC judgment completed
- System normal
ABNORMAL
- DTC judgment completed
- System abnormal
INCOMPLETE
- DTC judgment not completed
- Perform driving pattern after confirming DTC enabling conditions
HINT:
- If the judgment result is NORMAL, the system is normal.
- If the judgment result is ABNORMAL, the system has a malfunction.
- If the judgment result is INCOMPLETE, perform steps [F] through [H].
- [A] to [E]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- When clearing the permanent DTCs, do not disconnect the cable from the auxiliary battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.
- With the engine running, accelerate the vehicle to 75 km/h or more by depressing the accelerator pedal for 10 seconds or more [F].
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
HINT:
If the engine stops, further depress the accelerator pedal to restart the engine.
- Idle the engine for 100 seconds or more [G].
HINT:
- P001400 is output:
With the shift lever in P.
- P001500 is output:
With the shift lever in D.
- P001400 is output:
- Enter the following menus: Powertrain / Engine / Trouble Codes [H].
- Read the pending DTCs.
HINT:
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
- Check the DTC judgment result again.
HINT:
- If the judgment result is NORMAL, the system is normal.
- If the judgment result is ABNORMAL, the system has a malfunction.
- [A] to [H]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- When clearing the permanent DTCs, do not disconnect the cable from the auxiliary battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.
NOTICE:
- Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the Freeze Frame Data and Vehicle Control History can be useful for troubleshooting.
Click here

(Select Powertrain in Health Check and then check the time stamp data.)
Click here

- If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.
Click here

HINT:
- DTC P001400 or P001500 may be stored when foreign matter in the engine oil is caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. This foreign matter may then be captured by the oil filter.
- Read Freeze Frame Data using the Techstream. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P001400 OR P001500)
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine / Trouble Codes.
(e) Read the DTCs.
Powertrain > Engine > Trouble CodesResult | Proceed to |
|---|---|
DTC P001400 or P001500 is output |
A |
DTC P001400 or P001500 and other DTCs are output |
B |
HINT:
If any DTCs other than P001400 or P001500 are output, troubleshoot those DTCs first.
| B | GO TO DTC CHART |
|
PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EXHAUST VVT OCV DUTY RATIO BANK 1)
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Put the engine in Inspection Mode (Maintenance Mode).
Powertrain > Hybrid Control > UtilityInspection Mode
(e) Start the engine.
(f) Enter the following menus: Powertrain / Engine / Active Test / Control the Exhaust VVT OCV Duty Ratio Bank 1.
Powertrain > Engine > Active TestControl the Exhaust VVT OCV Duty Ratio Bank 1
(g) Check the engine speed while operating the cam timing oil control solenoid assembly using the Techstream.
OK:
Techstream Operation | Engine Condition |
|---|---|
0% |
Normal engine speed |
100% |
Engine idles roughly or stalls |
HINT:
- Refer to "Data List / Active Test" [Exhaust VVT Hold Learn Value Bank 1, Exhaust VVT Change Angle Bank 1, Exhaust VVT OCV Control Duty Ratio Bank 1 and Exhaust VVT Target Angle Bank 1].
Click here

- Test not possible with the shift lever in P during charge control. Move the shift lever to N to perform test.
- If the DTCs are stored after the Active Test, clear the DTCs.
| NG | GO TO STEP 5 |
|
CLEAR DTC
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Clear the DTCs.
Powertrain > Engine > Clear DTCsHINT:
- P001400 is output:
Clear the DTC not using the Techstream.
- P001500 is output:
Clear the DTC using the Techstream.
(e) Turn the power switch off and wait for at least 30 seconds.
|
CHECK WHETHER DTC OUTPUT RECURS (DTC P001400 OR P001500)
(a) Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
(b) Enter the following menus: Powertrain / Engine / Trouble Codes.
(c) Read the DTCs.
Powertrain > Engine > Trouble CodesResult | Proceed to |
|---|---|
DTCs are not output |
A |
DTC P001400 or P001500 is output |
B |
HINT:
DTC P001400 or P001500 may be stored when foreign matter in the engine oil is caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. That foreign matter may then be captured by the oil filter.
| A | CHECK FOR INTERMITTENT PROBLEMS |
|
INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY
(a) Inspect the cam timing oil control solenoid assembly.
Click here ![]()
| NG | GO TO STEP 11 |
|
INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (EXHAUST CAMSHAFT TIMING GEAR BOLT ASSEMBLY)
(a) Inspect the camshaft timing oil control valve assembly (exhaust camshaft timing gear bolt assembly).
Click here ![]()
| NG | GO TO STEP 13 |
|
CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TEETH ON TIMING CHAIN)
(a) Remove the cylinder head cover sub-assembly.
Click here ![]()
(b) Turn the crankshaft pulley and align its groove with the TDC timing mark of the timing chain cover.
(c) Check that the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly are at the positions shown in the illustration. HINT: If the timing marks are not as shown, turn the crankshaft one revolution clockwise. OK: Timing marks on camshaft timing gear assembly and camshaft timing exhaust gear assembly are at the positions shown in the illustration. HINT: If the result is not as specified, check for mechanical malfunctions that may have affected the valve timing, such as a jumped tooth or stretching of the timing chain. |
|
| OK | GO TO STEP 15 |
|
CHECK ENGINE MECHANICAL SYSTEM
(a) Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.
HINT:
Perform "Inspection After Repair" after repairing or replacing the engine mechanical system.
Click here ![]()
| NG | REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA |
|
CLEAR DTC
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Clear the DTCs.
Powertrain > Engine > Clear DTCsHINT:
- P001400 is output:
Clear the DTC not using the Techstream.
- P001500 is output:
Clear the DTC using the Techstream.
(e) Turn the power switch off and wait for at least 30 seconds.
|
CHECK WHETHER DTC OUTPUT RECURS (DTC P001400 OR P001500)
(a) Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
(b) Enter the following menus: Powertrain / Engine / Trouble Codes.
(c) Read the DTCs.
Powertrain > Engine > Trouble CodesResult | Proceed to |
|---|---|
DTCs are not output |
A |
DTC P001400 or P001500 is output |
B |
| A | CHECK FOR INTERMITTENT PROBLEMS |
| B | REPLACE ECM |
REPLACE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY
(a) Replace the cam timing oil control solenoid assembly.
Click here ![]()
|
INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (EXHAUST CAMSHAFT TIMING GEAR BOLT ASSEMBLY)
(a) Inspect the camshaft timing oil control valve assembly (exhaust camshaft timing gear bolt assembly).
Click here ![]()
| OK | GO TO STEP 14 |
|
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (EXHAUST CAMSHAFT TIMING GEAR BOLT ASSEMBLY)
(a) Replace the camshaft timing oil control valve assembly (exhaust camshaft timing gear bolt assembly).
Click here ![]()
|
PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EXHAUST VVT OCV DUTY RATIO BANK 1)
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Put the engine in Inspection Mode (Maintenance Mode).
Powertrain > Hybrid Control > UtilityInspection Mode
(e) Start the engine.
(f) Enter the following menus: Powertrain / Engine / Active Test / Control the Exhaust VVT OCV Duty Ratio Bank 1.
Powertrain > Engine > Active TestControl the Exhaust VVT OCV Duty Ratio Bank 1
(g) Check the engine speed while operating the cam timing oil control solenoid assembly using the Techstream.
OK:
Techstream Operation | Engine Condition |
|---|---|
0% |
Normal engine speed |
100% |
Engine idles roughly or stalls |
HINT:
- Refer to "Data List / Active Test" [Exhaust VVT Hold Learn Value Bank 1, Exhaust VVT Change Angle Bank 1, Exhaust VVT OCV Control Duty Ratio Bank 1 and Exhaust VVT Target Angle Bank 1].
Click here

- Test not possible with the shift lever in P during charge control. Move the shift lever to N to perform test.
- If the DTCs are stored after the Active Test, clear the DTCs.
| OK | END |
|
REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
(a) Replace the camshaft timing exhaust gear assembly.
Click here ![]()
HINT:
Perform "Inspection After Repair" after replacing the camshaft timing exhaust gear assembly.
Click here ![]()
|
CLEAR DTC
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Clear the DTCs.
Powertrain > Engine > Clear DTCsHINT:
- P001400 is output:
Clear the DTC not using the Techstream.
- P001500 is output:
Clear the DTC using the Techstream.
(e) Turn the power switch off and wait for at least 30 seconds.
|
CHECK WHETHER DTC OUTPUT RECURS (DTC P001400 OR P001500)
(a) Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
(b) Enter the following menus: Powertrain / Engine / Trouble Codes.
(c) Read the DTCs.
Powertrain > Engine > Trouble CodesResult | Proceed to |
|---|---|
DTCs are not output |
A |
DTC P001400 or P001500 is output |
B |
| A | END |
| B | REPLACE ECM |
