Driver Assistance System - Basic Inspection
- Additional Service When Replacing Adas Control Unit 2
- Configuration (adas Control Unit 2)
- Pre-Inspection for Diagnosis
- Steering Torque Calibration
- Mac Key Writing
Additional Service When Replacing Adas Control Unit 2 Nissan Pathfinder 2022
Work Procedure
Always perform the additional service after replacing the ADAS control unit 2.
ADAS CONTROL UNIT 2 CONFIGURATION
Perform the ADAS control unit 2 configuration. Refer to Work Procedure.
>>GO TO 2.
WRITING MAC KEY
Turn ignition switch OFF.
Turn ignition switch ON.
Perform MAC key writing. Refer to Work Procedure.
With ProPILOT Assist>>GO TO 3.
Without ProPILOT Assist>>INSPECTION END
STEERING TORQUE CALIBRATION
Turn ignition switch OFF.
Turn ignition switch ON.
Perform the steering torque calibration. Refer to Work Procedure.
>>INSPECTION END
Configuration (adas Control Unit 2) Nissan Pathfinder R53
Work Procedure
Vehicle specification needs to be written with CONSULT because it is not written after replacing the ADAS control unit 2.
The configuration requires network connection. CONSULT connects to network and then it downloads the configuration data from the server. Then CONSULT writes the Nissan Pathfinder vehicle specification to the ADAS control unit 2.
The configuration no need to “save” configuration data from the ADAS control unit 2. The configuration data is always generated freshly at the server and then downloaded to the CONSULT.
WRITING VEHICLE SPECIFICATION
With CONSULT
Perform writing Nissan Pathfinder vehicle specification to ADAS control unit 2 following "Automatic Configuration" procedure of "Configuration" according to CONSULT Operation Manual.
>>WORK END
Pre-Inspection for Diagnosis Nissan Pathfinder R53
Work Procedure
CHECK THE STEERING WHEEL
Is the steering wheel equipped with a cover or other materials?
YES>>Remove the steering wheel cover or other materials.
NO>>Inspection End.
Steering Torque Calibration Nissan Pathfinder R53
Work Procedure
After replacing the ADAS control unit 2 and after replacing or removing the following steering components, the steering torque calibration is necessary to operate the system normally.
Steering wheel
Spiral cable
Steering angle sensor
Steering column assembly
Steering gear assembly
Work Procedure (Preparation)
PERFORM SELF-DIAGNOSIS
Start the engine.
Perform self-diagnosis of "ICC/ADAS 2".
Check if any DTC is detected.
Is any DTC detected?
YES>>Perform diagnosis on the detected DTC and repair or replace the applicable item. Refer to DTC Index.
NO>>GO TO 2.
PREPARATION BEFORE STEERING TORQUE CALIBRATION
Perform pre-inspection for diagnosis. Refer to Work Procedure.
Place the car on a level surface.
Adjust the tire pressure to the specified pressure value.
Maintain no-load in Nissan Pathfinder vehicle.
Check if the following conditions are satisfied.
Engine: Running
Shift position: P Range
Steering wheel: Center (within ±15 degrees)
ProPILOT Assist: OFF
Nissan Pathfinder Vehicle speed: 0 km/h
ADAS control unit 2 voltage: More than 10.5 V
Release the parking brake.
Refer to Work Procedure (Steering Torque Calibration).
Work Procedure (Steering Torque Calibration)
STEERING TORQUE CALIBRATION
CONSULT
Select "Work Support", then "Steering Torque Calibration".
Select "START" to begin the Steering Torque Calibration.
Confirm the displayed item.
“Completed”: Select “Completion”.
“Abnormally completed”: Perform the following services.
Displayed item possible cause service procedure:
| Possible Cause | Action |
|---|---|
| Steering wheel torque value is out range. |
|
| Out of execution condition. |
|
| Calibration for torque value is abnormally completed. | Touch "Retry". |
Confirm that “Completed” is displayed and then select “End” to close the adjustment procedure.
YES>>Work End.
Mac Key Writing Nissan Pathfinder
Work Procedure
When replacing ADAS control unit 2, it is necessary to write MAC key to ADAS control unit 2. Write MAC key to ADAS control unit 2 according to "MAC Key writing" procedure of "CONSULT Operation Manual".
Ignition switch ON
CONSULT is connected to internet
PERFORM MAC KEY WRITING
Ignition switch ON.
Select "MAC Key writing" on "Work Support" of "ICC/ADAS 2" using CONSULT.
Touch "Write".
WORK END