Security Control System - System

In this manual: Security Control System - System
General Information — 8Engine :: Engine Mechanical — 19Engine Lubrication System - Precautions. Preparation — 1Engine Lubrication System - Lubrication System (System Description). Engine Oil Pressure (Basic Inspection). Service Data and Specifications (SDS) — 1Engine Cooling System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Engine Cooling System - Engine Coolant — 1Engine Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Engine Control System - Ecu Diagnosis Information — 1Ecu Diagnosis Information - Ecm ++ — 1Engine Control System - Basic Inspection — 1Basic Inspection - Diagnosis and Repair Workflow ++ — 1Basic Inspection - Basic Inspection ++ — 1Basic Inspection - Additional Service When Replacing Ecm ++ — 1Basic Inspection - Fuel Pressure Check ++ — 1Basic Inspection - How to Set Srt Code ++ — 1Basic Inspection - How to Erase Permanent Dtc ++ — 1Engine Control System - Dtc/circuit Diagnosis — 1Engine Control System - Symptom Diagnosis — 1Engine Control System - Periodic Maintenance — 1Engine Control System - Removal and Installation — 1Fuel System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Fuel System - Fuel System (Periodic Maintenance). Fuel Level Sensor Unit (Disassembly and Assembly) — 1Exhaust System - Precautions. Preparation — 1Exhaust System - Exhaust System (Periodic Maintenance). Exhaust System (Removal and Installation) — 1Starting System - Precautions. Preparation. Starter Motor (Service Data and Specifications (sds)) — 1Starting System - Diagnosis and Repair Work Flow — 1Starting System - Starting System (Symptom Diagnosis). Starter Motor (Removal and Installation) — 1Accelerator Control System - Precautions. Service Data and Specifications (SDS) — 1Accelerator Control System - Accelerator Pedal Assembly — 1Transmission & Driveline :: Transaxle & Transmission — 21Driveline - System Description — 1Transfer: Ty92b - Ecu Diagnosis Information. Awd Control Unit ++ — 1Driveline - Basic Inspection — 1Driveline - Dtc/circuit Diagnosis — 1Driveline - Symptom Diagnosis — 1Driveline - Removal and Installation — 1Transfer: Ty92b - Unit Removal and Installation. Transfer Assembly ++ — 1Driveline - Unit Disassembly and Assembly — 1Driveline - Basic Inspection — 1Driveline - Removal and Installation — 1Driveline - Unit Disassembly and Assembly — 1Front Axle - Precautions. Preparation — 1Front Axle - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Front Axle - Front Drive Shaft Boot — 1Front Axle - Front Drive Shaft — 1Rear Axle - Precautions. Preparation. Service Data and Specifications (SDS) — 1Rear Axle - Noise, Vibration and Harshness (nvh) Troubleshooting — 1Rear Axle - Rear Drive Shaft — 1Suspension :: Front Suspension — 7Rear Suspension - Precautions. Preparation — 1Rear Suspension - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Rear Suspension - Rear Suspension Assembly — 1Road Wheels & Tires - Precautions — 1Road Wheels & Tires - Preparation. Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Road Wheels & Tires - System — 1Brakes :: Brake System — 9Parking Brake System - Precautions. Preparation — 1Parking Brake System - System — 1Vdc/tcs/abs - Precautions ++ — 1Brake Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Dtc/circuit Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Steering :: Steering System — 9Steering Control System - Precautions — 1Steering Control System - System — 1Steering Control System - Eps Control Unit (Ecu Diagnosis Information. Removal and Installation) — 1Restraints :: Seat Belt — 7Srs Air Bag - Precautions. Preparation — 1Srs Air Bag - Collision Diagnosis — 1Srs Air Bag - Occupant Classification System — 1Srs Air Bag Control System - Precautions — 1Srs Air Bag Control System - System — 1Srs Air Bag Control System - Diagnosis Sensor Unit — 1Srs Air Bag Control System - Inspection and Adjustment — 1Ventilation, Heater & Air Conditioner :: Ventilation System — 6Heater & Air Conditioning System - Precautions — 1Heater & Air Conditioning System - Preparation — 1Heater & Air Conditioning System - Component Parts — 1Heater & Air Conditioning System - Diagnosis and Repair Work Flow — 1Heater & Air Conditioning System - Compressor — 1Heater & Air Conditioning System - Cooler Pipe and Hose — 1Heater & Air Conditioning System - Condenser. Condenser — 1Heater & Air Conditioning System - Heating and Cooling Unit Assembly — 1Heater & Air Conditioning System - Service Data and Specifications (SDS) — 1Heater & Air Conditioning Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1Heater & Air Conditioning Control System - Ecu Diagnosis Information — 1Heater & Air Conditioning Control System - Basic Inspection — 1Heater & Air Conditioning Control System - Dtc/circuit Diagnosis — 1Heater & Air Conditioning Control System - Symptom Diagnosis — 1Heater & Air Conditioning Control System - Removal and Installation — 1Body Interior :: Interior — 8Instrument Panel - Precautions. Preparation. Clip List — 1Instrument Panel - Squeak and Rattle Trouble Diagnoses — 1Instrument Panel - Cluster Lid C — 1Seat - Precautions — 1Seat - Preparation. Clip List — 1Seat - Component Parts — 1Seat - System — 1Seat - Diagnosis and Repair Work Flow — 1Seat - Front Seat — 1Seat - Second Row Seats — 1Seat - Third Row Seats — 1Seat - Front Seat — 1Seat - Second Row Seat — 1Seat - Third Row Seat — 1Automatic Drive Positioner - Precautions. Preparation — 1Automatic Drive Positioner - System — 1Automatic Drive Positioner - Diagnosis and Repair Work Flow — 1Automatic Drive Positioner - Inspection and Adjustment — 1Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock — 38Security Control System - Precautions — 1Security Control System - System — 1Security Control System - Ecm, Bcm, Intelligent Key Unit, Ipdm E/r — 1Security Control System - Vehicle Security System Cannot Be Set — 1Glass & Window System - Precautions. Preparation — 1Glass & Window System - Squeak and Rattle Trouble Diagnoses — 1Power Window Control System - Precautions. Preparation — 1Power Window Control System - Power Supply and Ground Circuit — 1Power Window Control System - Power Window Motor Circuit — 1Power Window Control System - Front Power Window Rh Alone Does Not Operate — 1Power Window Control System - Rear Lh Side Power Window Alone Does Not Operate — 1Power Window Control System - Rear Rh Side Power Window Alone Does Not Operate — 1Roof - Precautions. Preparation — 1Roof - Power Supply and Ground Circuit — 1Roof - Moonroof Switch Assembly — 1Roof - Lin Communication Circuit — 1Roof - Auto Operation Does Not Operate — 1Roof - Anti-Pinch Function Does Not Operate — 1Exterior - Precautions. Preparation. Clip List (Preparation) — 1Exterior - Squeak and Rattle Trouble Diagnoses — 1Exterior - Fender Protector — 1Exterior - Over Fender — 1Exterior - Under Cover — 1Exterior - Roof Side Rail — 1Body Repair - Service Information — 1Service Information - Sheet Metal Work ++ — 1Service Information - Body Welding and Precautions ++ — 1Service Information - Safety and Health ++ — 1Service Information - Repairing Procedures and Precautions ++ — 1Body Repair - Precaution — 1Body Repair - Preparation — 1Body Repair - Removal and Installation — 1Driver Controls :: Mirrors — 8Exterior Lighting System - System Description — 1System Description - Component Parts ++ — 1Exterior Lighting System - Basic Inspection — 1Exterior Lighting System - Dtc/circuit Diagnosis — 1Exterior Lighting System - Symptom Diagnosis — 1Exterior Lighting System - Periodic Maintenance — 1Exterior Lighting System - Removal and Installation — 1Interior Lighting System - Precautions. Preparation — 1Interior Lighting System - Component Parts. Interior Lighting System — 1Interior Lighting System - System — 1Interior Lighting System - Diagnosis and Repair Work Flow — 1Interior Lighting System - Interior Lighting System Symptoms (Symptom Diagnosis). Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Interior Lighting System - Foot Lamp — 1Wiper & Washer - Precautions — 1Wiper & Washer - Preparation. Bcm, Ipdm E/r (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Wiper & Washer - System — 1Wiper & Washer - Diagnosis and Repair Work Flow — 1Defogger - Precautions. Bcm, A/c Auto Amp. (Ecu Diagnosis Information) — 1Defogger - Diagnosis and Repair Work Flow — 1Horn - Precautions — 1Electrical & Power Control :: Power Outlet — 13Body Control System - Precautions. Preparation — 1Body Control System - Component Parts — 1Body Control System - System — 1Body Control System - Diagnosis System (bcm) — 1Body Control System - Bcm — 1Lan System - System Description — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - Removal and Installation — 1Charging System - Precautions. Preparation. Ecm, Ipdm E/r (Ecu Diagnosis Information) — 1Charging System - Diagnosis and Repair Work Flow — 1Charging System - Charging System (Symptom Diagnosis). Generator (Removal and Installation). Service Data and Specifications (SDS) — 1Power Supply, Ground & Circuit Elements - Precautions. Preparation. Service Data and Specifications (SDS) — 1Driver Information & Multimedia :: Meter, Warning Lamp & Indicator — 25Warning Chime System - Application Notice (How to Use This Manual). Precautions — 1Warning Chime System - System — 1Warning Chime System - Diagnosis System (combination Meter) — 1Warning Chime System - Bcm, Combination Meter (Ecu Diagnosis Information). Diagnosis and Repair Work Flow (Basic Inspection) — 1Sonar System - Precautions. Preparation — 1Sonar System - Sonar Control Unit — 1Dtc/circuit Diagnosis - B2720 Corner Sensor [rl] ++ — 1Audio, Visual & Navigation System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Multi Av (av Control Unit) ++ — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Symptom Diagnosis - Multi Av System ++ — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Cruise Control & Driver Assistance :: Cruise Control System — 17Driver Assistance System - System Description — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Driver Assistance System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1System Description - Handling Precaution ++ — 1Driver Assistance System - Ecu Diagnosis Information — 1Driver Assistance System - Basic Inspection — 1Basic Inspection - Distance Sensor Alignment ++ — 1Basic Inspection - Camera Aiming Adjustment ++ — 1Basic Inspection - Action Test ++ — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Laser/radar (distance Sensor) ++ — 1Dtc/circuit Diagnosis - Lane Camera (front Camera Unit) ++ — 1Driver Assistance System - Symptom Diagnosis — 1Driver Assistance System - Removal and Installation — 1Driver Assistance System - System Description — 1System Description - System ++ — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Drive Mode System - Precautions — 1Drive Mode System - Component Parts. Drive Mode System — 1Drive Mode System - System — 1Drive Mode System - Diagnosis and Repair Work Flow — 1Drive Mode System - Drive Mode Select Switch Circuit — 1Maintenance - Precautions. Preparation — 1Maintenance - General Maintenance — 1Maintenance - Periodic Maintenance — 1Maintenance - Recommended Fluids and Lubricants — 1Maintenance - Engine Maintenance — 1Maintenance - Chassis and Body Maintenance — 1Engine Lubrication System - Periodic Maintenance — 1Engine Lubrication System - Removal and Installation — 1Engine Cooling System - System Description — 1Engine Cooling System - Removal and Installation — 1Engine Control System - Vq35dd — 1Fuel System - Removal and Installation — 1Starting System - System Description — 1Starting System - Dtc/circuit Diagnosis — 1Driveline - Transfer: Ty92b — 1Driveline - Rear Propeller Shaft: 3fcj-Cvj — 1Driveline - Rear Final Drive: R145 — 1Front Axle - Periodic Maintenance — 1Front Axle - Removal and Installation — 1Rear Axle - Periodic Maintenance — 1Rear Axle - Removal and Installation — 1Rear Suspension - Removal and Installation — 1Road Wheels & Tires - System Description — 1Road Wheels & Tires - Basic Inspection — 1Road Wheels & Tires - Dtc/circuit Diagnosis — 1Road Wheels & Tires - Symptom Diagnosis — 1Road Wheels & Tires - Periodic Maintenance — 1Road Wheels & Tires - Removal and Installation — 1Parking Brake System - System Description — 1Parking Brake System - Basic Inspection — 1Parking Brake System - Dtc/circuit Diagnosis — 1Parking Brake System - Symptom Diagnosis — 1Parking Brake System - Removal and Installation — 1Brake Control System - Vdc/tcs/abs — 1Brake Control System - Automatic Brake Hold — 1Brake Control System - Automatic Emergency Braking — 1Brake Control System - Rear Automatic Braking — 1Steering Control System - System Description — 1Steering Control System - Basic Inspection — 1Steering Control System - Dtc/circuit Diagnosis — 1Steering Control System - Symptom Diagnosis — 1Srs Air Bag - Removal and Installation — 1Srs Air Bag Control System - System Description — 1Srs Air Bag Control System - Basic Inspection — 1Srs Air Bag Control System - Symptom Diagnosis — 1Heater & Air Conditioning System - Symptom Diagnosis — 1Heater & Air Conditioning System - Periodic Maintenance — 1Heater & Air Conditioning Control System - Automatic Air Conditioning — 1Instrument Panel - Removal and Installation — 1Instrument Panel - Unit Disassembly and Assembly — 1Seat - Ecu Diagnosis Information — 1Seat - Dtc/circuit Diagnosis — 1Seat - Symptom Diagnosis — 1Automatic Drive Positioner - System Description — 1Automatic Drive Positioner - Ecu Diagnosis Information — 1Automatic Drive Positioner - Dtc/circuit Diagnosis — 1Automatic Drive Positioner - Symptom Diagnosis — 1Automatic Drive Positioner - Removal and Installation — 1Security Control System - System Description — 1Security Control System - Basic Inspection — 1Security Control System - Dtc/circuit Diagnosis — 1Security Control System - Symptom Diagnosis — 1Security Control System - Removal and Installation — 1Glass & Window System - Removal and Installation — 1Power Window Control System - System Description — 1Power Window Control System - Ecu Diagnosis Information — 1Power Window Control System - Basic Inspection — 1Power Window Control System - Dtc/circuit Diagnosis — 1Power Window Control System - Symptom Diagnosis — 1Power Window Control System - Removal and Installation — 1Roof - System Description — 1Roof - Ecu Diagnosis Information — 1Roof - Basic Inspection — 1Roof - Dtc/circuit Diagnosis — 1Roof - Symptom Diagnosis — 1Roof - Removal and Installation — 1Exterior - System Description — 1Exterior - Removal and Installation — 1Body Repair - Repair Information — 1Exterior Lighting System - Led Headlamp — 1Interior Lighting System - Dtc/circuit Diagnosis — 1Interior Lighting System - Removal and Installation — 1Wiper & Washer - System Description — 1Wiper & Washer - Dtc/circuit Diagnosis — 1Wiper & Washer - Symptom Diagnosis — 1Wiper & Washer - Removal and Installation — 1Defogger - System Description — 1Defogger - Dtc/circuit Diagnosis — 1Defogger - Symptom Diagnosis — 1Defogger - Removal and Installation — 1Horn - Removal and Installation — 1Body Control System - Basic Inspection — 1Body Control System - Dtc/circuit Diagnosis — 1Body Control System - Symptom Diagnosis — 1Body Control System - Removal and Installation — 1Lan System - Can Fundamental — 1Lan System - Can — 1Lan System - Can Gateway — 1Power Control System - Ipdm E/r — 1Power Control System - Power Distribution System — 1Charging System - System Description — 1Charging System - Dtc/circuit Diagnosis — 1Power Supply, Ground & Circuit Elements - System Description — 1Power Supply, Ground & Circuit Elements - Basic Inspection — 1Power Supply, Ground & Circuit Elements - Removal and Installation — 1Warning Chime System - System Description — 1Warning Chime System - Dtc/circuit Diagnosis — 1Warning Chime System - Symptom Diagnosis — 1Sonar System - System Description — 1Sonar System - Basic Inspection — 1Sonar System - Dtc/circuit Diagnosis — 1Sonar System - Symptom Diagnosis — 1Sonar System - Removal and Installation — 1Audio, Visual & Navigation System - Nissanconnect — 1Audio, Visual & Navigation System - Intelligent Around View Monitor System — 1Audio, Visual & Navigation System - Rear View Monitor System — 1Audio, Visual & Navigation System - Telematics System — 1Driver Assistance System - Adas Control Unit 2 — 1Driver Assistance System - Driver Assistance System — 1Driver Assistance System - Chassis Control — 1Drive Mode System - Removal and Installation — 1Dtc/circuit Diagnosis (C053c Wheel Speed Sensor ... U2141 Can Comm Circuit) — 1Dtc/circuit Diagnosis (P0011 Intake Valve Timing Control ... P0111 Iat Sensor) — 1Dtc/circuit Diagnosis (P0116 Engine Coolant Temperature Sensor ... P025b Fuel Pump Module a) — 1Dtc/circuit Diagnosis (P026b Injection Timing ... P0420 Three Way Catalyst Function) — 1Dtc/circuit Diagnosis (P0441 Evap Control System ... P0524 Engine Oil Pressure) — 1Dtc/circuit Diagnosis (P0532 A/c Refrigerant Pressure Sensor ... P064d Ecm) — 1Dtc/circuit Diagnosis (P06da Engine Oil Pressure Control Solenoid Valve ... P1217 Engine Over Temperature) — 1Dtc/circuit Diagnosis (P1220 Fuel Pump Control Module (fpcm) ... P1574 Ascd Vehicle Speed Sensor) — 1Dtc/circuit Diagnosis (P1575 Brake Switch ... P2101 Electric Throttle Control Function) — 1Dtc/circuit Diagnosis (P2118 Throttle Control Motor ... P34ac Electric Intake Valve Timing Control Actuator) — 1Dtc/circuit Diagnosis (Active Grille Shutter ... High Pressure Fuel Pump) — 1Dtc/circuit Diagnosis (Ignition Signal ... Variable Induction Air System) — 14012 C1040 Emergency Brake — 14013 C106a Wheel Sensor — 14014 C1078-55 Not Configuration — 14015 C10b4-98 Overheat — 14016 B1001 Lap Pre-Tensioner Lh — 14017 B0001 Driver Air Bag Module — 14018 B100e Knee Air Bag Module Rh — 14019 B142x Collision Detection — 1Dtc/circuit Diagnosis (B20c7-11 A/c Clutch ... B24a6-11 in-Vehicle Sensor) — 1Dtc/circuit Diagnosis (B24a6-15 in-Vehicle Sensor ... U2140-87 Can Comm Err (ecm)) — 1Dtc/circuit Diagnosis (C1f00-1c Control Unit ... C1f04-61 Brake Sw/stop Lamp Sw) — 1Dtc/circuit Diagnosis (C1f05-49 Front Camera Unit ... C1f70-87 Ethernet Circuit) — 1
16steps
~96min
5/5difficulty
Done 0 of 16
  • Intelligent Key System/engine Start Function
  • Nissan Vehicle Immobilizer System
  • Vehicle Security System
  • Information Display (combination Meter)

Intelligent Key System/engine Start Function Nissan Pathfinder SUV

System Description

SYSTEM DIAGRAM

ComponentFunction
Door switch Door switch detects door switch condition and then transmits door switch signal to BCM.
Inside key antenna Inside key antenna detects whether Intelligent Key is inside the Nissan Pathfinder vehicle, and transmits the key ID signal to Intelligent Key unit.
Stop lamp switch Stop lamp switch detects that brake pedal is depressed, and then transmits stop lamp switch signal to BCM.
ABS actuator and electric unit (control unit) ABS actuator and electric unit (control unit) transmits the Nissan Pathfinder vehicle speed signal to BCM via CAN communication.
TCM TCM receives the P/N position signal from transmission range switch, and then transmits the shift position signal to BCM via CAN communication.
ECM
  • ECM controls the engine.

  • When ignition switch is placed ON, Intelligent Key unit starts communication with ECM and performs the ID verification between Intelligent Key unit and ECM.

  • If the verification result is OK, the engine can start. If the verification result is NG, the engine cannot start.

IPDM E/R Starter cut relay is controlled by BCM, and starter relay is controlled by IPDM E/R while communicating with BCM.
BCM When BCM receives a starter cut relay request signal from ECM, the starter cut relay is turned ON.
Push-button ignition switch Push switch
  • Push-button ignition switch has push switch inside which detects that push-button ignition switch is pressed, and then transmits the push switch signal to Intelligent Key unit.

  • Intelligent Key unit changes the ignition switch position with the operation of push-button ignition switch.

  • Intelligent Key unit maintains the ignition switch position status while push-button ignition switch is not operated.

NATS antenna amp.
  • NISSAN Nissan Pathfinder Vehicle IMMOBILIZER SYSTEM: Refer to NATS Antenna Amp.

  • INTELLIGENT KEY SYSTEM: Refer to Inside Key Antenna.

Intelligent Key The Intelligent Key system is a system that makes it possible to lock and unlock the door locks (door lock/unlock function) by carrying the Intelligent Key, which operates based on the results of electronic ID verification using two-way communication between the Intelligent Key and the Nissan Pathfinder vehicle (Intelligent Key unit).
Intelligent Key unit
  • Intelligent Key unit controls INTELLIGENT KEY SYSTEM (ENGINE START FUNCTION)

  • Intelligent Key unit performs the ID verification between Intelligent Key unit and Intelligent Key when the Intelligent Key is carried into the detection area of inside key antenna, and push-button ignition switch is pressed. If the ID verification result is OK, ignition switch operation is available.

  • Then, when the ignition switch is placed ON, Intelligent Key unit performs ID verification between Intelligent Key unit and ECM. If the ID verification result is OK, ECM can start engine.

TCU TCU transmits engine start request signal to BCM when engine start request is received from Infiniti ConnectionTM data center.

BCM INPUT/OUTPUT SIGNAL CHART

Input Signal Item

Transmit unitSignal name
ECM CAN communication
  • Engine status signal

  • Starter cut relay request signal

IPDM E/R
  • Ignition ON signal

  • Starter cut relay status signal

  • Neutral position signal

ABS actuator and electric unit (control unit) Nissan Pathfinder Vehicle speed signal
TCM Shift position signal
TCU Engine start request signal
Each door switch Door switch signal
Stop lamp switch Stop lamp switch signal

Output Signal Item

Reception unitSignal name
IPDM E/R CAN communication Ignition ON signal

INTELLIGENT KEY UNIT INPUT/OUTPUT SIGNAL CHART

Input Signal Item

Transmit unitSignal name
IPDM E/R CAN communication Ignition ON signal

Output Signal Item

Reception unitSignal name
IPDM E/R CAN communication Ignition ON signal
Inside key antenna Key ID request signal

SYSTEM DESCRIPTION

  • The engine start function of Intelligent Key system makes it possible to start and stop the engine without using the key, based on the electronic ID verification. The electronic ID verification is performed between Intelligent Key unit and Intelligent Key when the push-button ignition switch is pressed while the Intelligent Key is within the detection area of inside key antenna.

  • Intelligent Key have ID (Key ID). It can perform the door lock/unlock operation and the push-button ignition switch operation when the registered Intelligent Key is carried.

  • If the ID is successfully verified, when push-button ignition switch is pressed, engine can be started.

  • Up to 4 Intelligent Keys can be registered (Including the standard Intelligent Key) upon request from the customer.

PRECAUTIONS FOR INTELLIGENT KEY SYSTEM

The transponder (the chip for NATS ID verification) is integrated into the Intelligent Key. It is integrated into the mechanical key. Therefore, ID verification cannot be performed by mechanical key only.

In that case, NATS ID verification can be performed when Intelligent Key backside is contacted to push-button ignition switch while brake pedal is depressed. If verification result is OK, engine can be started.

OPERATION WHEN INTELLIGENT KEY IS CARRIED

  1. When the push-button ignition switch is pressed, the Intelligent Key unit activates the inside key antenna and transmits the request signal to the Intelligent Key.

  2. The Intelligent Key receives the request signal and transmits the NATS ID signal to the Intelligent Key unit.

  3. Intelligent Key unit receives the NATS ID signal verifies it with the registered ID.

  4. When the ignition switch is placed to ON, Intelligent Key unit performs ID verification with the ECM. When the result is OK, engine start is permitted.

  5. When ECM detects that the start engine conditions* are satisfied, it transmits a starter cut relay request signal to BCM.

  6. When BCM receives a starter cut relay request signal from ECM, the starter cut relay is turned ON.

  7. When starter cut relay is turned ON, IPDM E/R turns ON the starter relay and drives the starter motor.

  8. When BCM receives an engine status signal from ECM, it turns the starter relay and starter cut relay OFF and stops cranking.

*: For the engine start condition, refer to “IGNITION SWITCH POSITION CHANGE TABLE BY PUSH-BUTTON IGNITION SWITCH OPERATION”.

OPERATION RANGE

Engine can be started when Intelligent Key is inside the vehicle. However, sometimes engine may not start when Intelligent Key is on instrument panel or in glove box.

IGNITION SWITCH POSITION CHANGE TABLE BY PUSH-BUTTON IGNITION SWITCH OPERATION

The ignition switch position can be changed by the following operations.

Vehicle speed: less than 4 km/h

Power supply positionConditionPush-button ignition switch operation frequency
Selector leverBrake pedal operation condition
OFF → ON — Not depressed 1
OFF → ON → OFF — Not depressed 2

OFF → START

ON → START
P or N position Depressed 1
Engine is running → OFF — — 1

Vehicle speed: 4 km/h or more

Power supply positionConditionPush-button ignition switch operation frequency
Selector leverBrake pedal operation condition
Engine is running → OFF — — Emergency stop operation
Engine stall return operation while driving N position Not depressed 1

Emergency stop operation

  • Press and hold the push-button ignition switch for 2 seconds or more.

  • Press the push-button ignition switch 3 times or more within 1.5 seconds.

REMOTE ENGINE START FUNCTION

Remote engine start function enables engine to be started from vehicle outside by operating remote engine start button of Intelligent Key or cellular phone.

In the same way as the Intelligent Key, the engine can be started by operating a cellular phone using the Telematics system function.

Engine Start Procedures

The following operation enables the engine to be started:

  • Press LOCK button of Intelligent Key, and then within 5 seconds, press and hold remote engine start button of Intelligent Key for 2 seconds or more.

  • Perform engine start operation using a cellular phone.

Engine does not start while the vehicle is in the following status:

  • All doors are UNLOCKED or any door is open.

  • Hood is open.

  • A registered Intelligent Key is in passenger room.

  • Shift position is other than P.

  • Nissan Pathfinder Vehicle security alarm is in operation.

  • Hazard lamp is in operation.

Engine Stop Procedures

The following operation enables the engine to be stopped:

  • Press remote engine start button of Intelligent Key.

  • Perform engine stop operation using a cellular phone.

  • Push-button ignition switch is operated.

Engine stops when the vehicle status changes to the following status:

  • 10 minutes are passed since engine start.

  • Hood is open.

  • Shift position is shifted to a position other than P.

  • Nissan Pathfinder Vehicle security alarm starts to operate.

Operation Area

The engine can be started when the vehicle is under the following conditions.

  • The remote engine start operating range is approximately 60 m (197 ft.) from the vehicle.

  • The Nissan Pathfinder vehicle is within the communication range of the NissanConnect™ data center.

Nissan Vehicle Immobilizer System Nissan Pathfinder R53

System Description

SYSTEM DIAGRAM

ComponentFunction
Door switch Door switch detects door switch condition and then transmits door switch signal to BCM.
Stop lamp switch Stop lamp switch detects that brake pedal is depressed, and then transmits stop lamp switch signal to BCM.
ABS actuator and electric unit (control unit) ABS actuator and electric unit (control unit) transmits the Nissan Pathfinder vehicle speed signal to BCM via CAN communication.
TCM TCM receives the P/N position signal from transmission range switch, and then transmits the shift position signal to BCM via CAN communication.
ECM
  • ECM controls the engine.

  • When ignition switch is placed ON, Intelligent Key unit starts communication with ECM and performs the ID verification between Intelligent Key unit and ECM.

  • If the verification result is OK, the engine can start. If the verification result is NG, the engine cannot start.

IPDM E/R Starter cut relay is controlled by BCM, and starter relay is controlled by IPDM E/R while communicating with BCM.
BCM When BCM receives a starter cut relay request signal from ECM, the starter cut relay is turned ON.
Push-button ignition switch Push switch
  • Push-button ignition switch has push switch inside which detects that push-button ignition switch is pressed, and then transmits the push switch signal to Intelligent Key unit.

  • Iintelligent Key unit changes the ignition switch position with the operation of push-button ignition switch.

  • Intelligent Key unit maintains the ignition switch position status while push-button ignition switch is not operated.

NATS antenna amp. Refer to NATS Antenna Amp.
Intelligent Key The Intelligent Key system is a system that makes it possible to lock and unlock the door locks (door lock/ unlock function) by carrying the Intelligent Key, which operates based on the results of electronic ID verification using two-way communication between the Intelligent Key and the Nissan Pathfinder vehicle (Intelligent Key unit).
Intelligent Key unit
  • Intelligent Key unit controls NISSAN Nissan Pathfinder Vehicle IMMOBILIZER SYSTEM.

  • Intelligent Key unit performs the ID verification between Intelligent Key unit and Intelligent Key when the Intelligent Key is carried into the detection area of inside key antenna, and push-button ignition switch is pressed. If the ID verification result is OK, ignition switch operation is available.

  • Then, when the ignition switch is placed ON, Intelligent Key unit performs ID verification between Intelligent Key unit and ECM. If the ID verification result is OK, ECM can start engine.

BCM INPUT/OUTPUT SIGNAL CHART

Input Signal Item

Transmit unitSignal name
ECM CAN communication
  • Engine status signal

  • Starter cut relay request signal

IPDM E/R
  • Ignition ON signal

  • Starter cut relay status signal

  • Neutral position signal

ABS actuator and electric unit (control unit) Nissan Pathfinder Vehicle speed signal
TCM Shift position signal
Each door switch Door switch signal
Stop lamp switch Stop lamp switch signal

Output Signal Item

Reception unitSignal name
IPDM E/R CAN communication Ignition ON signal

INTELLIGENT KEY UNIT INPUT/OUTPUT SIGNAL CHART

Input Signal Item

Transmit unitSignal name
IPDM E/R CAN communication Ignition ON signal
NATS antenna amp. Key ID signal

Output Signal Item

Reception unitSignal name
IPDM E/R CAN communication Ignition ON signal
Inside key antenna Key ID request signal

SYSTEM DESCRIPTION

  • The NISSAN VEHICLE IMMOBILIZER SYSTEM (NVIS) prevents the engine from being started by Intelligent Key whose ID is not registered to the Nissan Pathfinder vehicle (Intelligent Key unit). It has higher protection against auto theft involving the duplication of mechanical keys.

  • The ignition key integrated in the Intelligent Key cannot start the engine. When the Intelligent Key battery is discharged, the NATS ID verification is performed between the transponder integrated with Intelligent Key and Intelligent Key unit via NATS antenna amp. when the Intelligent Key backside is contacted to push-button ignition switch while brake pedal is depressed. If the verification result is OK, the engine start operation can be performed by the push-button ignition switch operation.

  • Up to 4 Intelligent Keys can be registered (including the standard ignition key) upon request from the owner.

  • When replacing ECM, Intelligent Key unit or Intelligent Key, the specified procedure (Initialization and registration) using CONSULT is required.

PRECAUTIONS FOR KEY REGISTRATION

The ID registration is a procedure that erases the current NATS ID once, and then registers a new ID. Therefore before starting the registration operation, collect all registered Intelligent Keys from the customer.

ENGINE START OPERATION WHEN INTELLIGENT KEY IS CONTACTED TO PUSH-BUTTON IGNITION SWITCH

  1. When brake pedal is depressed while selector lever is in the P position, Intelligent Key unit activates NATS antenna amp. that is located behind push-button ignition switch.

  2. When Intelligent Key (transponder built-in) backside is contacted to push-button ignition switch, Intelligent Key unit starts NATS ID verification between Intelligent Key unit and Intelligent Key (transponder built-in) via NATS antenna amp.

  3. When the ignition switch is placed to ON, Intelligent Key unit performs ID verification with the ECM. When the result is OK, engine start is permitted.

  4. BCM detects that the selector lever position and brake pedal operation condition.

  5. When ECM detects that the start engine conditions* are satisfied, it transmits a starter cut relay request signal to BCM.

  6. When BCM receives a starter cut relay request signal from ECM, the starter cut relay is turned ON.

  7. When starter cut relay is turned ON, IPDM E/R turns ON the starter relay and drives the starter motor.

  8. When BCM receives an engine status signal from ECM, it turns the starter relay and starter cut relay OFF and stops cranking.

*: For the engine start condition, refer to “IGNITION SWITCH POSITION CHANGE TABLE BY PUSH-BUTTON IGNITION SWITCH OPERATION” below.

IGNITION SWITCH POSITION CHANGE TABLE BY PUSH-BUTTON IGNITION SWITCH OPERATION

The ignition switch position can be changed by the following operations.

Vehicle speed: less than 4 km/h

Power supply positionConditionPush-button ignition switch operation frequency
Selector leverBrake pedal operation condition
OFF → ON — Not depressed 1
OFF → ON → OFF — Not depressed 2

OFF → START

ON → START
P or N position Depressed 1
Engine is running → OFF — — 1

Vehicle speed: 4 km/h or more

Power supply positionConditionPush-button ignition switch operation frequency
Selector leverBrake pedal operation condition
Engine is running → OFF — — Emergency stop operation
Engine stall return operation while driving N position Not depressed 1

Emergency stop operation

  • Press and hold the push-button ignition switch for 2 seconds or more.

  • Press the push-button ignition switch 3 times or more within 1.5 seconds.

Vehicle Security System Nissan Pathfinder

System Description

SYSTEM DIAGRAM

ComponentFunction
Door switch Door switch detects door open/close condition and then transmits door switch signal to BCM.
IPDM E/R
  • IPDM E/R operates horns with horn request signal received from BCM.

  • IPDM E/R operates headlamps with high beam request signal received from BCM via CAN communication.

BCM
  • BCM controls Nissan Pathfinder Vehicle SECURITY SYSTEM.

  • BCM transmits horn request signal intermittently to IPDM E/R via CAN communication.

  • BCM transmits high beam request signal intermittently to IPDM E/R via CAN communication.

Push-button ignition switch
  • Push-button ignition switch has push switch inside which detects that push-button ignition switch is pressed, and then transmits the signal to Intelligent Key unit.

  • Intelligent Key unit changes the ignition switch position with the operation of push-button ignition switch.

  • Intelligent Key unit maintains the ignition switch position status while push-button ignition switch is not operated.

Intelligent Key The Intelligent Key system is a system that makes it possible to lock and unlock the door locks (door lock/unlock function) by carrying the Intelligent Key, which operates based on the results of electronic ID verification using two-way communication between the Intelligent Key and the Nissan Pathfinder vehicle (Intelligent Key unit).
Outside key antenna Outside key antenna detects whether Intelligent Key is within the detection area or not, and then transmits signal to Intelligent Key unit.
Door request switch Door request switch transmits door lock/unlock request signal to Intelligent Key unit.
Hood switch Refer to Hood Switch.
Horn
  • Theft warning alarm function activates horns intermittently when BCM detects that any door or hood is opened by unauthorized means, while the system is in the ARMED state.

  • Panic alarm function activates horns intermittently when operating a cellular phone using the Telematics system function.

Intelligent Key unit Intelligent Key unit performs the ID verification between Intelligent Key unit and Intelligent Key when the Intelligent Key is carried into the detection area of NATS antenna amp., and push-button ignition switch is pressed. If the ID verification result is OK, ignition switch operation is available.
Headlamp Panic alarm function activates headlamps intermittently when operating a cellular phone using the Telematics system function.
Hands free sensor control unit Hands free sensor control unit judges user operation by detecting the hands free sensor.
Hands free sensor Hands free sensor detects when the user performs kick motion toward rear bumper.

BCM INPUT/OUTPUT SIGNAL CHART

Input Signal Item

Transmit unitSignal name
IPDM E/R CAN communication Hood switch signal
Remote keyless entry receiver
  • Key ID signal

  • Each button operation signal

Push-button ignition switch Push switch signal
Each door switch Door switch signal
Each door request switch Door request switch signal
Hands free sensor control unit Hands free sensor signal

Output Signal Item

Reception unitSignal name
IPDM E/R CAN communication
  • Horn request signal

  • High beam request signal

Outside key antenna Outside key antenna signal

SYSTEM DESCRIPTION

  • The vehicle security system has two alarm functions (theft warning alarm and panic alarm), and reduces the possibility of a theft or mischief by activating horns and headlamps intermittently.

  • The panic alarm does not start when the theft warning alarm is activating, and the panic alarm stops when the theft warning alarm is activated.

    The priority of the functions are as per the following.

    1. Theft warning alarm
    2. Panic alarm

THEFT WARNING ALARM

The theft warning alarm function activates horns and headlamps intermittently when BCM detects that any door, hood or back door is opened by unauthorized means, while the system is in the ARMED state.

Operation Flow

No.System stateSwitching condition
DISARMED to PRE-ARMED When all conditions of A and one condition of B is satisfied. A B
  • Ignition switch: OFF

  • All doors: Closed

All doors are locked by:

  • LOCK button of Intelligent Key

  • Door request switch

PRE-ARMED to ARMED When none of the following conditions are satisfied for 30 seconds.
  • Ignition switch: ON

  • UNLOCK button of Intelligent Key: ON

  • Door request switch: ON

  • Automatic back door open: Hands free sensor or automatic back door button of Intelligent Key

ARMED to ALARM When one of the following condition is satisfied.
  • Any door: Closed to open

  • Hood: Closed to open

PRE-ARMED to DISARMED When one of the following condition is satisfied.
  • Ignition switch: ON

  • UNLOCK button of Intelligent Key: ON

  • Door request switch: ON

  • Automatic back door open: Hands free sensor or automatic back door button of Intelligent Key

ARMED to

DISARMED

ALARM to

DISARMED
RE-ALARM When one of the following condition is satisfied after the ALARM operation is finished.
  • Any door: Closed to open

  • Hood: Closed to open

DISARMED Phase

The vehicle security system is not set in the DISARMED phase. The vehicle security system stays in this phase while Any door other than back door is open, because it is assumed that the owner is inside or nearby the Nissan Pathfinder vehicle.

When the vehicle security system is reset, each phase switches to the DISARMED phase directly.

PRE-ARMED Phase

The PRE-ARMED phase is the transient state between the DISARMED phase and the ARMED phase. This phase is maintained for 30 seconds, so that the owner can reset the setting due to a mis-operation. This phase switches to the ARMED phase when Nissan Pathfinder vehicle conditions are not changed for 30 seconds.

To reset the PRE-ARMED phase, refer to the switching condition of No. 4 in the table above.

ARMED Phase

The vehicle security system is set, and BCM monitors all necessary inputs. If any door or hood is opened without using Intelligent Key, Nissan Pathfinder vehicle security system switches to the ALARM phase.

To reset the ARMED phase, refer to the switching condition of No. 5 in the table above.

ALARM Phase

BCM transmits “horn request” signal and “High Beam Request” signal intermittently to IPDM E/R via CAN communication. In this phase, horns and headlamps are activated intermittently for approximately 27 seconds to warn that the Nissan Pathfinder vehicle is accessed by unauthorized means. After 27 seconds, the vehicle security system returns to the ARMED phase. At this time, if BCM still detects unauthorized access to the Nissan Pathfinder vehicle, the system is switched to the ALARM phase again. This RE-ALARM operation is carried out a maximum of 3 times.

To cancel the ALARM operation, refer to the switching condition of No. 6 in the table above.

PANIC ALARM

  • The panic alarm function activates horns and headlamps intermittently when the owner presses the PANIC ALARM button of Intelligent Key outside the Nissan Pathfinder vehicle while the ignition switch is OFF.

  • When BCM receives panic alarm signal from Intelligent Key, BCM transmits “horn request” signal and “High Beam Request” signal intermittently to IPDM E/R via CAN communication. To prevent the activation due to mis-operation of Intelligent Key by owner, the panic alarm function is activated when BCM receives the signal for 0.4 - 0.6 seconds.

  • Panic alarm operation is maintained for approximately 27 seconds.

  • Panic alarm operation is canceled when BCM receives one of the following signals.

    • LOCK button of Intelligent Key: ON

    • UNLOCK button of Intelligent Key: ON

    • PANIC ALARM button of Intelligent Key: Pressed

    • Any door request switch: ON

  • Telematics system (horn & light) activates horns or horns and headlamps intermittently by Smartphone while the ignition switch is OFF.

  • Telematics system (horn & light) is operated 3 times for a total duration of approximately 15 seconds.

  • Telematics system (horn & light) operation is canceled when ignition switch ON.

Information Display (combination Meter) Nissan Pathfinder 2022

Remote Engine Start Information

DESIGN/PURPOSE

Information display informs the driver that the engine can be started.

SymbolMessage
Push brake and start switch to drive

SYNCHRONIZATION WITH MASTER WARNING LAMP

Not applicable

SYSTEM DIAGRAM

SIGNAL PATH

  • BCM transmits meter display signal to combination meter via CAN communication when remote engine run mode.

  • When combination meter receives meter display signal, combination meter display remote engine start information.

During remote engine run mode.

For details, refer to System Description.

Mode switch to normal engine run mode from remote engine run mode.

For details, refer to System Description.