Driveline - Basic Inspection
- Diagnosis and Repair Work Flow
- Additional Service When Replacing Awd Control Unit (in Electro-Hydraulic Coupling)
- Air Bleeding and Initialize Oil Deterioration Level
Diagnosis and Repair Work Flow Nissan Pathfinder Fifth generation
Work Flow
DETAILED FLOW
INTERVIEW FROM THE CUSTOMER
Clarify customer complaints before inspection. First of all, perform an interview utilizing Diagnostic Work Sheet and reproduce symptoms as well as fully understand it. Ask customer about his/her complaints carefully. Check symptoms by driving Nissan Pathfinder vehicle with customer, if necessary.
>>GO TO 2.
CHECK SYMPTOM
Reproduce the symptom that is indicated by the customer, based on the information from the customer obtained by interview. Also check that the symptom is not caused by protection function. Refer to Protection Function.
>>GO TO 3.
PERFORM SELF-DIAGNOSIS
CONSULT
Select “Self Diagnostic Result” mode of “ALL MODE AWD/4WD”.
Is any DTC detected?
YES>>Record or print self-diagnosis results. GO TO 4.
NO>>GO TO 6.
RECHECK SYMPTOM
CONSULT
Erase self-diagnostic results for “ALL MODE AWD/4WD”.
Perform DTC confirmation procedures for the error detected system.
Is any DTC detected?
YES>>GO TO 5.
NO>>Check harness and connectors based on the information obtained by interview. Refer to Intermittent Incident.
REPAIR OR REPLACE ERROR-DETECTED PARTS
Repair or replace error-detected parts.
Reconnect part or connector after repairing or replacing.
When DTC is detected, erase self-diagnostic results for “ALL MODE AWD/4WD”.
GO TO 7.
IDENTIFY ERROR-DETECTED SYSTEM BY SYMPTOM DIAGNOSIS
Estimate error-detected system based on symptom diagnosis and perform inspection.
Can the error-detected system be identified?
YES>>GO TO 7.
NO>>Check harness and connectors based on the information obtained by interview. Refer to Intermittent Incident.
FINAL CHECK
CONSULT
Check the reference value for 4WD control unit.
Recheck the symptom and check that symptom is not reproduced on the same conditions.
Is the symptom reproduced?
YES>>GO TO 3.
NO>>Inspection End.
Diagnostic Work Sheet
Description
In general, customers have their own criteria for a problem. Therefore, it is important to understand the symptom and status well enough by asking the customer about his/her concerns carefully. To systemize all the information for the diagnosis, prepare the interview sheet referring to the interview points.
In some cases, multiple conditions that appear simultaneously may cause a DTC to be detected.
Interview sheet sample
| Interview sheet | |||||
|---|---|---|---|---|---|
| Customer name | MR/MS | Registration number | Initial year registration | ||
| Nissan Pathfinder Vehicle type | VIN | ||||
| Storage date | Engine | Mileage | Mile (km) | ||
| Symptom | □Nissan Pathfinder Vehicle does not enter 4WD mode. | ||||
| □4WD warning icon/display is displayed. | |||||
| □Heavy tight-corner braking symptom occurs | |||||
| □Noise □Vibration | |||||
□Others ( ) |
|||||
| First occurrence | □Recently □Others ( ) | ||||
| Frequency of occurrence | □Always □Under a certain conditions of □Sometimes (time(s)/day) | ||||
| Climate conditions | □Irrelevant | ||||
| Weather | □Fine □Cloud □Rain □Snow □Others ( ) | ||||
| Temperature | □Hot □Warm □Cool □Cold □Temperature (Approx. °C) | ||||
| Relative humidity | □High □Moderate □Low | ||||
| Road conditions | □Urban area □Suburb area □High way □Mountain road (uphill or down hill) □Rough road |
||||
| Operation conditions, etc. | □Irrelevant □When engine starts □During idling □During driving □During acceleration □At constant speed driving □During deceleration □During cornering (right curve or left curve) |
||||
| Other conditions | |||||
Memo |
|||||
Additional Service When Replacing Awd Control Unit (in Electro-Hydraulic Coupling) Nissan Pathfinder 2026
Description
When replacing 4WD control unit (integrated with actuator assembly of electro-hydraulic coupling assembly) and electro-hydraulic coupling assembly, the following work is required:
For the work procedure, refer to Work Procedure.
CONSULT
4WD control unit programming
Air bleeding and initialize oil deterioration level of electro-hydraulic coupling oil
Work Procedure
ASIST on the CONSULT has been synchronized to the current date.
All CONSULT software updates (if any) have been installed.
REPLACING CONTROL UNIT
Ignition switch OFF.
Replace electro-hydraulic coupling assembly or AWD control unit (integrated with actuator assembly). Refer to Disassembly.
GO TO 2.
PERFORM AWD CONTROL UNIT PROGRAMMIMG
CONSULT
Select “Re/programming, Configuration” from the main menu of the CONSULT.
Select “ALL MODE AWD/4WD” when prompted
Select “Data Via Auto Programming”, and follow the instructions according to the procedure in CONSULT Operation Manual.
GO TO 3.
PERFORM AIR BLEEDING AND INITIALIZE OIL DETERIORATION LEVEL
Perform air bleeding and initialize oil deterioration level of electro-hydraulic coupling oil. Refer to Description.
>>Work End.
Air Bleeding and Initialize Oil Deterioration Level Nissan Pathfinder Fifth generation
Description
When the electro-hydraulic coupling oil is drained, such as when replacing or removing/installing electro-hydraulic coupling component parts, the air bleeding and initialize oil deterioration level of electro-hydraulic coupling oil is required after fill with new electro-hydraulic coupling oil.
Work Procedure
PREPARATIONS BEFORE WORK
Set the vehicle in the following condition:
Temperature condition is 14°F (-10°C) or higher.
Nissan Pathfinder Vehicle is stopped on a flat place.
Engine running.
Battery voltage condition is 14.2 V or more.
GO TO 2.
AIR BLEEDING AND INITIALIZE OIL DETERIORATION LEVEL
CONSULT
Ignition switch OFF to ON.
Select “BLEED AIR & INITIALIZE OIL DETERIORATION LEVEL” in “Work support” mode of “ALL MODE AWD/4WD”.
Select “Start”.
Follow the instructions in CONSULT.
Is “Completed” displayed?
YES>>GO TO 3.
NO>>Perform self-diagnosis for “ALL MODE AWD/4WD” and check detected DTC. Refer to DTC Index.
CHECK OIL LEVEL
Check oil level for electro-hydraulic coupling oil again and add oil if necessary. Refer to Adjustment.
>>GO TO 4.
FINAL CHECK
CONSULT
Perform DTC confirmation procedure for DTC “C1220-54”. Refer to DTC Description.
Is DTC “C1220-54” detected?
YES>>Proceed to diagnosis procedure: Refer to DTC Diagnosis Procedure.
NO>>Work End.