Audio, Visual & Navigation System - Dtc/circuit Diagnosis

In this manual: Audio, Visual & Navigation System - Dtc/circuit Diagnosis
General Information — 8Engine :: Engine Mechanical — 19Engine Lubrication System - Precautions. Preparation — 1Engine Lubrication System - Lubrication System (System Description). Engine Oil Pressure (Basic Inspection). Service Data and Specifications (SDS) — 1Engine Cooling System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Engine Cooling System - Engine Coolant — 1Engine Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Engine Control System - Ecu Diagnosis Information — 1Ecu Diagnosis Information - Ecm ++ — 1Engine Control System - Basic Inspection — 1Basic Inspection - Diagnosis and Repair Workflow ++ — 1Basic Inspection - Basic Inspection ++ — 1Basic Inspection - Additional Service When Replacing Ecm ++ — 1Basic Inspection - Fuel Pressure Check ++ — 1Basic Inspection - How to Set Srt Code ++ — 1Basic Inspection - How to Erase Permanent Dtc ++ — 1Engine Control System - Dtc/circuit Diagnosis — 1Engine Control System - Symptom Diagnosis — 1Engine Control System - Periodic Maintenance — 1Engine Control System - Removal and Installation — 1Fuel System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Fuel System - Fuel System (Periodic Maintenance). Fuel Level Sensor Unit (Disassembly and Assembly) — 1Exhaust System - Precautions. Preparation — 1Exhaust System - Exhaust System (Periodic Maintenance). Exhaust System (Removal and Installation) — 1Starting System - Precautions. Preparation. Starter Motor (Service Data and Specifications (sds)) — 1Starting System - Diagnosis and Repair Work Flow — 1Starting System - Starting System (Symptom Diagnosis). Starter Motor (Removal and Installation) — 1Accelerator Control System - Precautions. Service Data and Specifications (SDS) — 1Accelerator Control System - Accelerator Pedal Assembly — 1Transmission & Driveline :: Transaxle & Transmission — 21Driveline - System Description — 1Transfer: Ty92b - Ecu Diagnosis Information. Awd Control Unit ++ — 1Driveline - Basic Inspection — 1Driveline - Dtc/circuit Diagnosis — 1Driveline - Symptom Diagnosis — 1Driveline - Removal and Installation — 1Transfer: Ty92b - Unit Removal and Installation. Transfer Assembly ++ — 1Driveline - Unit Disassembly and Assembly — 1Driveline - Basic Inspection — 1Driveline - Removal and Installation — 1Driveline - Unit Disassembly and Assembly — 1Front Axle - Precautions. Preparation — 1Front Axle - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Front Axle - Front Drive Shaft Boot — 1Front Axle - Front Drive Shaft — 1Rear Axle - Precautions. Preparation. Service Data and Specifications (SDS) — 1Rear Axle - Noise, Vibration and Harshness (nvh) Troubleshooting — 1Rear Axle - Rear Drive Shaft — 1Suspension :: Front Suspension — 7Rear Suspension - Precautions. Preparation — 1Rear Suspension - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Rear Suspension - Rear Suspension Assembly — 1Road Wheels & Tires - Precautions — 1Road Wheels & Tires - Preparation. Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Road Wheels & Tires - System — 1Brakes :: Brake System — 9Parking Brake System - Precautions. Preparation — 1Parking Brake System - System — 1Vdc/tcs/abs - Precautions ++ — 1Brake Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Dtc/circuit Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Steering :: Steering System — 9Steering Control System - Precautions — 1Steering Control System - System — 1Steering Control System - Eps Control Unit (Ecu Diagnosis Information. Removal and Installation) — 1Restraints :: Seat Belt — 7Srs Air Bag - Precautions. Preparation — 1Srs Air Bag - Collision Diagnosis — 1Srs Air Bag - Occupant Classification System — 1Srs Air Bag Control System - Precautions — 1Srs Air Bag Control System - System — 1Srs Air Bag Control System - Diagnosis Sensor Unit — 1Srs Air Bag Control System - Inspection and Adjustment — 1Ventilation, Heater & Air Conditioner :: Ventilation System — 6Heater & Air Conditioning System - Precautions — 1Heater & Air Conditioning System - Preparation — 1Heater & Air Conditioning System - Component Parts — 1Heater & Air Conditioning System - Diagnosis and Repair Work Flow — 1Heater & Air Conditioning System - Compressor — 1Heater & Air Conditioning System - Cooler Pipe and Hose — 1Heater & Air Conditioning System - Condenser. Condenser — 1Heater & Air Conditioning System - Heating and Cooling Unit Assembly — 1Heater & Air Conditioning System - Service Data and Specifications (SDS) — 1Heater & Air Conditioning Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1Heater & Air Conditioning Control System - Ecu Diagnosis Information — 1Heater & Air Conditioning Control System - Basic Inspection — 1Heater & Air Conditioning Control System - Dtc/circuit Diagnosis — 1Heater & Air Conditioning Control System - Symptom Diagnosis — 1Heater & Air Conditioning Control System - Removal and Installation — 1Body Interior :: Interior — 8Instrument Panel - Precautions. Preparation. Clip List — 1Instrument Panel - Squeak and Rattle Trouble Diagnoses — 1Instrument Panel - Cluster Lid C — 1Seat - Precautions — 1Seat - Preparation. Clip List — 1Seat - Component Parts — 1Seat - System — 1Seat - Diagnosis and Repair Work Flow — 1Seat - Front Seat — 1Seat - Second Row Seats — 1Seat - Third Row Seats — 1Seat - Front Seat — 1Seat - Second Row Seat — 1Seat - Third Row Seat — 1Automatic Drive Positioner - Precautions. Preparation — 1Automatic Drive Positioner - System — 1Automatic Drive Positioner - Diagnosis and Repair Work Flow — 1Automatic Drive Positioner - Inspection and Adjustment — 1Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock — 38Security Control System - Precautions — 1Security Control System - System — 1Security Control System - Ecm, Bcm, Intelligent Key Unit, Ipdm E/r — 1Security Control System - Vehicle Security System Cannot Be Set — 1Glass & Window System - Precautions. Preparation — 1Glass & Window System - Squeak and Rattle Trouble Diagnoses — 1Power Window Control System - Precautions. Preparation — 1Power Window Control System - Power Supply and Ground Circuit — 1Power Window Control System - Power Window Motor Circuit — 1Power Window Control System - Front Power Window Rh Alone Does Not Operate — 1Power Window Control System - Rear Lh Side Power Window Alone Does Not Operate — 1Power Window Control System - Rear Rh Side Power Window Alone Does Not Operate — 1Roof - Precautions. Preparation — 1Roof - Power Supply and Ground Circuit — 1Roof - Moonroof Switch Assembly — 1Roof - Lin Communication Circuit — 1Roof - Auto Operation Does Not Operate — 1Roof - Anti-Pinch Function Does Not Operate — 1Exterior - Precautions. Preparation. Clip List (Preparation) — 1Exterior - Squeak and Rattle Trouble Diagnoses — 1Exterior - Fender Protector — 1Exterior - Over Fender — 1Exterior - Under Cover — 1Exterior - Roof Side Rail — 1Body Repair - Service Information — 1Service Information - Sheet Metal Work ++ — 1Service Information - Body Welding and Precautions ++ — 1Service Information - Safety and Health ++ — 1Service Information - Repairing Procedures and Precautions ++ — 1Body Repair - Precaution — 1Body Repair - Preparation — 1Body Repair - Removal and Installation — 1Driver Controls :: Mirrors — 8Exterior Lighting System - System Description — 1System Description - Component Parts ++ — 1Exterior Lighting System - Basic Inspection — 1Exterior Lighting System - Dtc/circuit Diagnosis — 1Exterior Lighting System - Symptom Diagnosis — 1Exterior Lighting System - Periodic Maintenance — 1Exterior Lighting System - Removal and Installation — 1Interior Lighting System - Precautions. Preparation — 1Interior Lighting System - Component Parts. Interior Lighting System — 1Interior Lighting System - System — 1Interior Lighting System - Diagnosis and Repair Work Flow — 1Interior Lighting System - Interior Lighting System Symptoms (Symptom Diagnosis). Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Interior Lighting System - Foot Lamp — 1Wiper & Washer - Precautions — 1Wiper & Washer - Preparation. Bcm, Ipdm E/r (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Wiper & Washer - System — 1Wiper & Washer - Diagnosis and Repair Work Flow — 1Defogger - Precautions. Bcm, A/c Auto Amp. (Ecu Diagnosis Information) — 1Defogger - Diagnosis and Repair Work Flow — 1Horn - Precautions — 1Electrical & Power Control :: Power Outlet — 13Body Control System - Precautions. Preparation — 1Body Control System - Component Parts — 1Body Control System - System — 1Body Control System - Diagnosis System (bcm) — 1Body Control System - Bcm — 1Lan System - System Description — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - Removal and Installation — 1Charging System - Precautions. Preparation. Ecm, Ipdm E/r (Ecu Diagnosis Information) — 1Charging System - Diagnosis and Repair Work Flow — 1Charging System - Charging System (Symptom Diagnosis). Generator (Removal and Installation). Service Data and Specifications (SDS) — 1Power Supply, Ground & Circuit Elements - Precautions. Preparation. Service Data and Specifications (SDS) — 1Driver Information & Multimedia :: Meter, Warning Lamp & Indicator — 25Warning Chime System - Application Notice (How to Use This Manual). Precautions — 1Warning Chime System - System — 1Warning Chime System - Diagnosis System (combination Meter) — 1Warning Chime System - Bcm, Combination Meter (Ecu Diagnosis Information). Diagnosis and Repair Work Flow (Basic Inspection) — 1Sonar System - Precautions. Preparation — 1Sonar System - Sonar Control Unit — 1Dtc/circuit Diagnosis - B2720 Corner Sensor [rl] ++ — 1Audio, Visual & Navigation System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Multi Av (av Control Unit) ++ — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Symptom Diagnosis - Multi Av System ++ — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Cruise Control & Driver Assistance :: Cruise Control System — 17Driver Assistance System - System Description — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Driver Assistance System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1System Description - Handling Precaution ++ — 1Driver Assistance System - Ecu Diagnosis Information — 1Driver Assistance System - Basic Inspection — 1Basic Inspection - Distance Sensor Alignment ++ — 1Basic Inspection - Camera Aiming Adjustment ++ — 1Basic Inspection - Action Test ++ — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Laser/radar (distance Sensor) ++ — 1Dtc/circuit Diagnosis - Lane Camera (front Camera Unit) ++ — 1Driver Assistance System - Symptom Diagnosis — 1Driver Assistance System - Removal and Installation — 1Driver Assistance System - System Description — 1System Description - System ++ — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Drive Mode System - Precautions — 1Drive Mode System - Component Parts. Drive Mode System — 1Drive Mode System - System — 1Drive Mode System - Diagnosis and Repair Work Flow — 1Drive Mode System - Drive Mode Select Switch Circuit — 1Maintenance - Precautions. Preparation — 1Maintenance - General Maintenance — 1Maintenance - Periodic Maintenance — 1Maintenance - Recommended Fluids and Lubricants — 1Maintenance - Engine Maintenance — 1Maintenance - Chassis and Body Maintenance — 1Engine Lubrication System - Periodic Maintenance — 1Engine Lubrication System - Removal and Installation — 1Engine Cooling System - System Description — 1Engine Cooling System - Removal and Installation — 1Engine Control System - Vq35dd — 1Fuel System - Removal and Installation — 1Starting System - System Description — 1Starting System - Dtc/circuit Diagnosis — 1Driveline - Transfer: Ty92b — 1Driveline - Rear Propeller Shaft: 3fcj-Cvj — 1Driveline - Rear Final Drive: R145 — 1Front Axle - Periodic Maintenance — 1Front Axle - Removal and Installation — 1Rear Axle - Periodic Maintenance — 1Rear Axle - Removal and Installation — 1Rear Suspension - Removal and Installation — 1Road Wheels & Tires - System Description — 1Road Wheels & Tires - Basic Inspection — 1Road Wheels & Tires - Dtc/circuit Diagnosis — 1Road Wheels & Tires - Symptom Diagnosis — 1Road Wheels & Tires - Periodic Maintenance — 1Road Wheels & Tires - Removal and Installation — 1Parking Brake System - System Description — 1Parking Brake System - Basic Inspection — 1Parking Brake System - Dtc/circuit Diagnosis — 1Parking Brake System - Symptom Diagnosis — 1Parking Brake System - Removal and Installation — 1Brake Control System - Vdc/tcs/abs — 1Brake Control System - Automatic Brake Hold — 1Brake Control System - Automatic Emergency Braking — 1Brake Control System - Rear Automatic Braking — 1Steering Control System - System Description — 1Steering Control System - Basic Inspection — 1Steering Control System - Dtc/circuit Diagnosis — 1Steering Control System - Symptom Diagnosis — 1Srs Air Bag - Removal and Installation — 1Srs Air Bag Control System - System Description — 1Srs Air Bag Control System - Basic Inspection — 1Srs Air Bag Control System - Symptom Diagnosis — 1Heater & Air Conditioning System - Symptom Diagnosis — 1Heater & Air Conditioning System - Periodic Maintenance — 1Heater & Air Conditioning Control System - Automatic Air Conditioning — 1Instrument Panel - Removal and Installation — 1Instrument Panel - Unit Disassembly and Assembly — 1Seat - Ecu Diagnosis Information — 1Seat - Dtc/circuit Diagnosis — 1Seat - Symptom Diagnosis — 1Automatic Drive Positioner - System Description — 1Automatic Drive Positioner - Ecu Diagnosis Information — 1Automatic Drive Positioner - Dtc/circuit Diagnosis — 1Automatic Drive Positioner - Symptom Diagnosis — 1Automatic Drive Positioner - Removal and Installation — 1Security Control System - System Description — 1Security Control System - Basic Inspection — 1Security Control System - Dtc/circuit Diagnosis — 1Security Control System - Symptom Diagnosis — 1Security Control System - Removal and Installation — 1Glass & Window System - Removal and Installation — 1Power Window Control System - System Description — 1Power Window Control System - Ecu Diagnosis Information — 1Power Window Control System - Basic Inspection — 1Power Window Control System - Dtc/circuit Diagnosis — 1Power Window Control System - Symptom Diagnosis — 1Power Window Control System - Removal and Installation — 1Roof - System Description — 1Roof - Ecu Diagnosis Information — 1Roof - Basic Inspection — 1Roof - Dtc/circuit Diagnosis — 1Roof - Symptom Diagnosis — 1Roof - Removal and Installation — 1Exterior - System Description — 1Exterior - Removal and Installation — 1Body Repair - Repair Information — 1Exterior Lighting System - Led Headlamp — 1Interior Lighting System - Dtc/circuit Diagnosis — 1Interior Lighting System - Removal and Installation — 1Wiper & Washer - System Description — 1Wiper & Washer - Dtc/circuit Diagnosis — 1Wiper & Washer - Symptom Diagnosis — 1Wiper & Washer - Removal and Installation — 1Defogger - System Description — 1Defogger - Dtc/circuit Diagnosis — 1Defogger - Symptom Diagnosis — 1Defogger - Removal and Installation — 1Horn - Removal and Installation — 1Body Control System - Basic Inspection — 1Body Control System - Dtc/circuit Diagnosis — 1Body Control System - Symptom Diagnosis — 1Body Control System - Removal and Installation — 1Lan System - Can Fundamental — 1Lan System - Can — 1Lan System - Can Gateway — 1Power Control System - Ipdm E/r — 1Power Control System - Power Distribution System — 1Charging System - System Description — 1Charging System - Dtc/circuit Diagnosis — 1Power Supply, Ground & Circuit Elements - System Description — 1Power Supply, Ground & Circuit Elements - Basic Inspection — 1Power Supply, Ground & Circuit Elements - Removal and Installation — 1Warning Chime System - System Description — 1Warning Chime System - Dtc/circuit Diagnosis — 1Warning Chime System - Symptom Diagnosis — 1Sonar System - System Description — 1Sonar System - Basic Inspection — 1Sonar System - Dtc/circuit Diagnosis — 1Sonar System - Symptom Diagnosis — 1Sonar System - Removal and Installation — 1Audio, Visual & Navigation System - Nissanconnect — 1Audio, Visual & Navigation System - Intelligent Around View Monitor System — 1Audio, Visual & Navigation System - Rear View Monitor System — 1Audio, Visual & Navigation System - Telematics System — 1Driver Assistance System - Adas Control Unit 2 — 1Driver Assistance System - Driver Assistance System — 1Driver Assistance System - Chassis Control — 1Drive Mode System - Removal and Installation — 1Dtc/circuit Diagnosis (C053c Wheel Speed Sensor ... U2141 Can Comm Circuit) — 1Dtc/circuit Diagnosis (P0011 Intake Valve Timing Control ... P0111 Iat Sensor) — 1Dtc/circuit Diagnosis (P0116 Engine Coolant Temperature Sensor ... P025b Fuel Pump Module a) — 1Dtc/circuit Diagnosis (P026b Injection Timing ... P0420 Three Way Catalyst Function) — 1Dtc/circuit Diagnosis (P0441 Evap Control System ... P0524 Engine Oil Pressure) — 1Dtc/circuit Diagnosis (P0532 A/c Refrigerant Pressure Sensor ... P064d Ecm) — 1Dtc/circuit Diagnosis (P06da Engine Oil Pressure Control Solenoid Valve ... P1217 Engine Over Temperature) — 1Dtc/circuit Diagnosis (P1220 Fuel Pump Control Module (fpcm) ... P1574 Ascd Vehicle Speed Sensor) — 1Dtc/circuit Diagnosis (P1575 Brake Switch ... P2101 Electric Throttle Control Function) — 1Dtc/circuit Diagnosis (P2118 Throttle Control Motor ... P34ac Electric Intake Valve Timing Control Actuator) — 1Dtc/circuit Diagnosis (Active Grille Shutter ... High Pressure Fuel Pump) — 1Dtc/circuit Diagnosis (Ignition Signal ... Variable Induction Air System) — 14012 C1040 Emergency Brake — 14013 C106a Wheel Sensor — 14014 C1078-55 Not Configuration — 14015 C10b4-98 Overheat — 14016 B1001 Lap Pre-Tensioner Lh — 14017 B0001 Driver Air Bag Module — 14018 B100e Knee Air Bag Module Rh — 14019 B142x Collision Detection — 1Dtc/circuit Diagnosis (B20c7-11 A/c Clutch ... B24a6-11 in-Vehicle Sensor) — 1Dtc/circuit Diagnosis (B24a6-15 in-Vehicle Sensor ... U2140-87 Can Comm Err (ecm)) — 1Dtc/circuit Diagnosis (C1f00-1c Control Unit ... C1f04-61 Brake Sw/stop Lamp Sw) — 1Dtc/circuit Diagnosis (C1f05-49 Front Camera Unit ... C1f70-87 Ethernet Circuit) — 1
87steps
~522min
4/5difficulty
Done 0 of 87
  • B2a04 Calibration
  • B2a05 Configuration
  • B2a07 Steering Angle Sensor
  • B2a1a Rear Camera
  • B2a1f Camera Power Supply
  • B2a2c Power Supply
  • U1327 Mac Key Update
  • U2141 Can Comm Err (tcm)
  • U214f Mac Comm Error (bcm)
  • U2a04 Comm Bus Off Its1-Fd
  • Power Supply and Ground Circuit

B2a04 Calibration Nissan Pathfinder 2022

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
B2A04-51

Calibration

(Around view monitor control unit)
Diagnosis condition Ignition switch ON
Signal (terminal) —
Threshold Calibration is incomplete or the connected camera is different from the one when calibrated.
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

Camera calibration

FAIL-SAFE

  • Unmatched icon display (red) is displayed (applicable for unmatched camera only).

  • MOD (Moving Object Detection) function is stopped.

Confirmation Procedure

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Ignition switch OFF and wait at least 30 seconds.

  3. Ignition switch ON and wait at least 30 seconds or more.

  4. Select “Self Diagnostic Result” mode of “AVM”.

  5. Check DTC.

Is DTC B2A04–51 detected?

YES>>

Proceed to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM CALIBRATING CAMERA IMAGE

When DTC B2A04–51 is detected, perform camera calibration.

>>

Perform camera calibration. Refer to Work Procedure.

B2a05 Configuration Nissan Pathfinder SUV

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
B2A05–44

Configuration

(Around view monitor control unit)
Diagnosis condition Ignition switch ON
Signal (terminal) —
Threshold Internal abnormality
Diagnosis delay time 2 seconds or more
B2A05–45 Diagnosis condition Ignition switch ON
Signal (terminal) —
Threshold Internal abnormality
Diagnosis delay time 2 seconds or more
B2A05–46 Diagnosis condition Ignition switch ON
Signal (terminal) —
Threshold Internal abnormality
Diagnosis delay time 2 seconds or more
B2A05–49 Diagnosis condition Ignition switch ON
Signal (terminal) —
Threshold Internal abnormality
Diagnosis delay time 2 seconds or more
B2A05–55 Diagnosis condition Ignition switch ON
Signal (terminal) —
Threshold Configuration is incomplete
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Around view monitor control unit

  • Vehicle specification is incomplete

FAIL-SAFE

  • On applicable camera screen marking (Red) is displayed.

  • MOD (Moving Object Detection) function is stopped.

Confirmation Procedure

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Ignition switch OFF and wait at least 30 seconds.

  3. Ignition switch ON and wait at least 30 seconds or more.

  4. Select “Self Diagnostic Result” mode of “AVM”.

  5. Check DTC.

Is DTC B2A05 detected?

YES>>

Proceed to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

DETERMINE MALFUNCTION TYPE

CONSULT

  1. Ignition switch ON.

  2. Ignition switch OFF and wait at least 30 seconds.

  3. Ignition switch ON and wait at least 30 seconds or more.

  4. Select “Self Diagnostic Result” mode of “AVM”.

  5. Check DTC.

Is DTC B2A05–44, 45, 46, 49, or 55 detected?

YES>>

44, 45, 46 or 49 – GO TO 3.

YES>>

55 – GO TO 2.

NO>>

Refer to Intermittent Incident.

PERFORM CONFIGURATION PROCEDURE

Perform configuration of around view monitor control unit. Refer to Description.

>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to Confirmation Procedure.

Is DTC B1341–44, 45, 46,49 or 55 detected again?

YES>>

Replace around view monitor control unit. Refer to Removal and Installation.

NO>>

Inspection End.

B2a07 Steering Angle Sensor Nissan Pathfinder R53

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
B2A07–86

Steering angle sensor

(Steering angle sensor)
Diagnosis condition Ignition switch ON
Signal (terminal) CAN communication signal
Threshold The steering angle sensor is malfunctioning
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • ABS actuator and electric unit (control unit)

  • Steering angle sensor

  • Around view monitor control unit

FAIL-SAFE

  • Predicted course line is not displayed.

  • MOD (Moving Object Detection) function is cancelled.

Confirmation Procedure

CHECK DTC PRIORITY

If DTC B2A07–86 is displayed with DTC B2156–87, first perform the trouble diagnosis for DTC B2156–87.

Is DTC B2156–87 detected?

YES>>

Refer to DTC Description.

NO>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Ignition switch OFF and wait at least 30 seconds.

  3. Ignition switch ON and wait at least 30 seconds or more.

  4. Select “Self Diagnostic Result” mode of “AVM”.

  5. Check DTC.

Is DTC B2A07–86 detected?

YES>>

Proceed to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

CHECK SELF-DIAGNOSIS RESULTS

CONSULT

Check if U2156–87 is detected with B2A07–86 in “Self Diagnostic Result” mode of “AVM”.

Is U2156–87 detected?

YES>>

Perform diagnosis of U2156–87. Refer to DTC Description.

NO>>

GO TO 2.

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS RESULTS

CONSULT

  1. Ignition switch ON.

  2. Ignition switch OFF and wait at least 30 seconds.

  3. Ignition switch ON and wait at least 30 seconds or more.

  4. Select “Self Diagnostic Result” mode of “ABS”.

  5. Check DTC.

Are any DTCs detected?

YES>>

Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to DTC Index.

NO>>

Replace around view monitor control unit. Refer to Removal and Installation.

B2a1a Rear Camera Nissan Pathfinder R53

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
B2A1A-13

Rear camera

(Rear cameral)
Diagnosis condition Ignition switch ON
Signal (terminal) LVDS (rear camera)
Threshold Communication error with rear camera
Diagnosis delay time 30 seconds or more
B2A1A-31 Diagnosis condition Ignition switch ON
Signal (terminal) LVDS (rear camera)
Threshold Communication error with rear camera
Diagnosis delay time 30 seconds or more

POSSIBLE CAUSE

  • LVDS cable (between around view monitor control unit and rear camera)

  • Rear camera

FAIL-SAFE

  • Camera image may not be displayed

  • MOD (Moving Object Detection) function is stopped.

Confirmation Procedure

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Ignition switch OFF and wait at least 30 seconds.

  3. Ignition switch ON and wait at least 30 seconds or more.

  4. Select “Self Diagnostic Result” mode of “AVM”.

  5. Check DTC.

Is DTC B2A1A–13 or 31 detected?

YES>>

Proceed to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

CHECK LVDS CABLE 1

  1. Ignition switch OFF.

  2. Check the connection status of the LVDS cable connector. (around view monitor control unit side, wire to wire, and rear camera side)

Is inspection result normal?

YES>>

GO TO 2.

NO>>

Connect the LVDS cable connector correctly.

CHECK LVDS CABLE 2

  1. Ignition switch OFF.

  2. Disconnect around view monitor control unit connector and rear camera connector.

  3. Check continuity between around view monitor control unit harness connector and rear camera harness connector.

    Around view monitor control unit Rear camera Continuity
    Connector Terminals Connector Terminals
    M97 37 B463 1 Yes
    38 2
  4. Check continuity between around view monitor control unit harness connector and ground.

    Around view monitor control unit Ground Continuity
    Connector Terminal
    M97 37 No

Is inspection result normal?

YES>>

Replace rear camera. Refer to Removal and Installation.

NO>>

Replace LVDS cable.

B2a1f Camera Power Supply Nissan Pathfinder 5th Gen

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
B2A1F-16

Camera power supply

(Camera power supply)
Diagnosis condition Ignition switch ON
Signal (terminal) Camera power supply
Threshold 0 V
Diagnosis delay time 30 seconds or more

POSSIBLE CAUSE

  • LVDS cable (between around view monitor control unit and each camera)

  • Around view monitor control unit

FAIL-SAFE

  • Camera image not displayed

  • MOD (Moving Object Detection) function is stopped.

Confirmation Procedure

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Ignition switch OFF and wait at least 30 seconds.

  3. Ignition switch ON and wait at least 30 seconds or more.

  4. Select “Self Diagnostic Result” mode of “AVM”.

  5. Check DTC.

Is DTC B2A1F–16 detected?

YES>>

Proceed to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

CHECK AROUND VIEW MONITOR CONTROL UNIT POWER SUPPLY CIRCUIT

Check around view monitor control unit power supply circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace malfunctioning parts.

CHECK LVDS CABLE 1

  1. Ignition switch OFF.

  2. Check the connection status of the LVDS cable connector (around view monitor control unit side, wire to wire, and each camera side)

    .

Is inspection result normal?

YES>>

GO TO 3.

NO>>

Connect the LVDS cable connector correctly.

CHECK LVDS CABLE 2

  1. Ignition switch OFF.

  2. Disconnect around view monitor control unit connector and each camera connector.

  3. Check continuity between around view monitor control unit harness connector and each camera harness connector.

    Around view monitor control unit Each camera Continuity
    Connector Terminals Connector Terminals
    M97 39 E226 (front camera) 1 Yes
    33 D51 (side camera LH) 1
    35 D151 (side camera RH) 1
    37 B463 (rear camera) 1

Is inspection result normal?

YES>>

Replace around view monitor control unit. Refer to Removal and Installation.

NO>>

Replace defective LVDS cable.

B2a2c Power Supply Nissan Pathfinder R53

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
B2A2C-A2

Power supply

(Power supply)
Diagnosis condition Ignition switch ON
Signal (terminal) ACC power supply
Threshold ACC power supply voltage is low
Diagnosis delay time 30 seconds or more

POSSIBLE CAUSE

  • ACC power supply circuit

  • Around view monitor control unit

FAIL-SAFE

  • Camera image not displayed

  • MOD (Moving Object Detection) function is stopped.

Confirmation Procedure

If DTC B2A07–86 is displayed with DTC B2156–87, first perform the trouble diagnosis for DTC B2156–87.

Is the applicable DTC detected?

YES>>

Perform diagnosis of DTC B2156–87. Refer to DTC Description.

NO>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Ignition switch OFF and wait at least 30 seconds.

  3. Ignition switch ON and wait at least 30 seconds or more.

  4. Select “Self Diagnostic Result” mode of “AVM”.

  5. Check DTC.

Is DTC B2A2C–A3 detected?

YES>>

Proceed to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

CHECK AROUND VIEW MONITOR CONTROL UNIT POWER SUPPLY CIRCUIT

Check around view monitor control unit power supply circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

Replace around view monitor control unit. Refer to Removal and Installation.

NO>>

Repair or replace malfunctioning parts.

U1327 Mac Key Update Nissan Pathfinder 2026

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition
U1327–52

MAC key update

(Message Authentication Code key update)
— Diagnosis condition —
Signal (terminal) —
Threshold MAC key writing is incomplete
Diagnosis delay time —
U1327–54 Diagnosis condition —
Signal (terminal) —
Threshold MAC key is not written after around view monitor control unit replacement
Diagnosis delay time —

POSSIBLE CAUSE

  • U1327–52:

    • Network communication error between CONSULT and around view monitor control unit

    • Around view monitor control unit used in other Nissan Pathfinder vehicle is installed in the vehicle

    • Around view monitor control unit

  • U1327–54:

    • Writing of MAC key has not been executed

    • Around view monitor control unit

FAIL-SAFE

—

Confirmation Procedure

DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Select “MAC Diagnosis” mode of “AVM”.

Is DTC U1327–52 or 54 detected as the current malfunction?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

DETERMINE MALFUNCTION TYPE

CONSULT

  1. Ignition switch ON.

  2. Select “MAC Diagnosis” mode of “AVM”.

Is DTC U1327 detected?

YES>>

GO TO 2.

YES>>

GO TO 4.

NO>>

Refer to Intermittent Incident.

PERFORM MAC KEY WRITING

CONSULT

  1. Perform MAC key writing. Refer to Description.

  2. Select “MAC Diagnosis” mode of “AVM”.

Is DTC U1327–54 detected as the current malfunction?

YES>>

GO TO 3.

NO>>

Inspection End.

PERFORM MAC KEY WRITING 2

CONSULT

  1. Perform MAC key writing. Refer to Description.

  2. Select “MAC Diagnosis” mode of “AVM”.

Is DTC U1327–54 detected as the current malfunction?

YES>>

GO TO 4.

NO>>

Inspection End.

PERFORM MAC KEY WRITING 3

CONSULT

  1. Perform MAC key writing. Refer to Description.

  2. Select “MAC Diagnosis” mode of “AVM”.

Is DTC U1327–52 or 54 detected as the current malfunction?

YES>>

Replace around view monitor control unit. Refer to Removal and Installation.

NO>>

Inspection End.

U2141 Can Comm Err (tcm) Nissan Pathfinder 2026

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U2141-87

CAN comm err (TCM)

[Controller area network communication error (TCM)]
Diagnosis condition Ignition switch ON
Signal (terminal) CAN communication signal
Threshold Communication error
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system (TCM)

FAIL-SAFE

  • Rear/front view is black screen (Bird-eye/Side view is displayed).

  • Rear view is not displayed even if shift lever is in R position.

  • MOD function does not operate.

Confirmation Procedure

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Ignition switch OFF and wait at least 30 seconds.

  3. Ignition switch ON and wait at least 30 seconds or more.

  4. Select “Self Diagnostic Result” mode of “AVM”.

  5. Check DTC.

Is DTC U2141–87 detected?

YES>>

Proceed to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to Confirmation Procedure.

Is DTC U2141-87 detected again?

YES>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

NO>>

Inspection End.

U214f Mac Comm Error (bcm) Nissan Pathfinder 2022

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC Detection Condition
U214F-57

CAN comm err (BCM)

[Control Area Network communication error (BCM)]
Diagnosis condition —
Signal (terminal) —
Threshold MAC communication error
Diagnosis delay time —

POSSIBLE CAUSE

  • MAC communication error

  • Around view monitor control unit used in other Nissan Pathfinder vehicles is installed in the vehicle

  • Around view monitor control unit

  • BCM

FAIL-SAFE

  • Camera image is not displayed.

  • MOD function does not operate.

Confirmation Procedure

CHECK DTC PRIORITY

If DTC U214F–57 is displayed with DTC U1327–52 or DTC U1327–54, first perform the trouble diagnosis for DTC U1327–52 or DTC U1327–54.

Is DTC U1327–52 or 54 detected?

YES>>

Refer to DTC Description.

NO>>

GO TO 2.

CHECK MAC DIAGNOSIS

CONSULT

  1. Ignition switch ON.

  2. Select “MAC Diagnosis” mode of “AVM”.

Is DTC U214F–57 detected?

YES>>

Proceed to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

CHECK DTC PRIORITY

If DTC U214F-57 is displayed with DTC U1327-52 or DTC U1327-54, first perform the trouble diagnosis for DTC U1327-52 or U1327-54.

Is DTC U1327-52 or 54 detected?

YES>>

Refer to DTC Description.

NO>>

GO TO 2.

CHECK MAC DIAGNOSIS

CONSULT

Perform “MAC Diagnosis” mode of “AVM” .

Is DTC U214F-57 detected with DTC U2152-57 and DTC U2176–57 at the same time?

YES>>

Replace around view monitor control unit. Refer to Removal and Installation.

NO>>

GO TO 3.

CHECK CAN COMMUNICATION SYSTEM

Check CAN communication system. Refer to Trouble Diagnosis Flow Chart.

>>

Inspection End.

U2a04 Comm Bus Off Its1-Fd Nissan Pathfinder SUV

DTC Description

DESCRIPTION

CAN (Controller Area Network) is a serial communication line for real time applications. It is an on-Nissan Pathfinder vehicle multiplex communication line with high data communication speed and excellent error detection ability. Modern Nissan Pathfinder vehicle is equipped with many electronic control unit, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with 2 communication lines (CAN-High line, CAN‐Low line) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only. CAN Communication Signal Chart. Refer to CAN Communication Signal Chart.

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U2A04-88

Comm Bus Off ITS1-FD

(Communication Bus Off Intelligent Transport System1-FD)
Diagnosis condition Ignition switch ON
Signal (terminal) CAN communication signal
Threshold Around view monitor control unit cannot communicate CAN communication signal
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

  • Camera image is not displayed.

  • MOD function does not operate.

Confirmation Procedure

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Ignition switch OFF and wait at least 30 seconds.

  3. Ignition switch ON and wait at least 30 seconds or more.

  4. Select “Self Diagnostic Result” mode of “AVM”.

  5. Check DTC.

Is DTC U2A04–88 detected?

YES>>

Proceed to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

CONSULT

  1. Ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to Confirmation Procedure.

Is DTC U2A04-88 detected again?

YES>>

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

NO>>

Inspection End.

Power Supply and Ground Circuit Nissan Pathfinder 2026

Diagnosis Procedure

CHECK FUSE

Check that the following fuse is not blown.

Terminal No.Signal nameFuse No.Capacity
17 Ignition signal 41 10 A

Is the fuse blown?

YES>>

Replace the blown fuse after repairing the affected circuit.

NO>>

GO TO 2.

CHECK POWER SUPPLY CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect around view monitor control unit connector.

  3. Check voltage between around view monitor control unit connector and ground.

    Around view monitor control unit(–)Condition

    Voltage

    (Approx.)
    ConnectorTerminal
    M96 17 Ground Ignition switch: ON Battery voltage

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace harness or connectors.

CHECK GROUND CIRCUIT

  1. Ignition switch OFF.

  2. Check continuity between around view monitor control unit connector and ground.

    Around view monitor control unit(–)Continuity
    ConnectorTerminal
    M96 16 Ground Yes

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Repair or replace harness or connectors.