Dtc/circuit Diagnosis (P0532 A/c Refrigerant Pressure Sensor ... P064d Ecm)

In this manual: Dtc/circuit Diagnosis (P0532 A/c Refrigerant Pressure Sensor ... P064d Ecm)
General Information — 8Engine :: Engine Mechanical — 19Engine Lubrication System - Precautions. Preparation — 1Engine Lubrication System - Lubrication System (System Description). Engine Oil Pressure (Basic Inspection). Service Data and Specifications (SDS) — 1Engine Cooling System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Engine Cooling System - Engine Coolant — 1Engine Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Engine Control System - Ecu Diagnosis Information — 1Ecu Diagnosis Information - Ecm ++ — 1Engine Control System - Basic Inspection — 1Basic Inspection - Diagnosis and Repair Workflow ++ — 1Basic Inspection - Basic Inspection ++ — 1Basic Inspection - Additional Service When Replacing Ecm ++ — 1Basic Inspection - Fuel Pressure Check ++ — 1Basic Inspection - How to Set Srt Code ++ — 1Basic Inspection - How to Erase Permanent Dtc ++ — 1Engine Control System - Dtc/circuit Diagnosis — 1Engine Control System - Symptom Diagnosis — 1Engine Control System - Periodic Maintenance — 1Engine Control System - Removal and Installation — 1Fuel System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Fuel System - Fuel System (Periodic Maintenance). Fuel Level Sensor Unit (Disassembly and Assembly) — 1Exhaust System - Precautions. Preparation — 1Exhaust System - Exhaust System (Periodic Maintenance). Exhaust System (Removal and Installation) — 1Starting System - Precautions. Preparation. Starter Motor (Service Data and Specifications (sds)) — 1Starting System - Diagnosis and Repair Work Flow — 1Starting System - Starting System (Symptom Diagnosis). Starter Motor (Removal and Installation) — 1Accelerator Control System - Precautions. Service Data and Specifications (SDS) — 1Accelerator Control System - Accelerator Pedal Assembly — 1Transmission & Driveline :: Transaxle & Transmission — 21Driveline - System Description — 1Transfer: Ty92b - Ecu Diagnosis Information. Awd Control Unit ++ — 1Driveline - Basic Inspection — 1Driveline - Dtc/circuit Diagnosis — 1Driveline - Symptom Diagnosis — 1Driveline - Removal and Installation — 1Transfer: Ty92b - Unit Removal and Installation. Transfer Assembly ++ — 1Driveline - Unit Disassembly and Assembly — 1Driveline - Basic Inspection — 1Driveline - Removal and Installation — 1Driveline - Unit Disassembly and Assembly — 1Front Axle - Precautions. Preparation — 1Front Axle - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Front Axle - Front Drive Shaft Boot — 1Front Axle - Front Drive Shaft — 1Rear Axle - Precautions. Preparation. Service Data and Specifications (SDS) — 1Rear Axle - Noise, Vibration and Harshness (nvh) Troubleshooting — 1Rear Axle - Rear Drive Shaft — 1Suspension :: Front Suspension — 7Rear Suspension - Precautions. Preparation — 1Rear Suspension - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Rear Suspension - Rear Suspension Assembly — 1Road Wheels & Tires - Precautions — 1Road Wheels & Tires - Preparation. Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Road Wheels & Tires - System — 1Brakes :: Brake System — 9Parking Brake System - Precautions. Preparation — 1Parking Brake System - System — 1Vdc/tcs/abs - Precautions ++ — 1Brake Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Dtc/circuit Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Steering :: Steering System — 9Steering Control System - Precautions — 1Steering Control System - System — 1Steering Control System - Eps Control Unit (Ecu Diagnosis Information. Removal and Installation) — 1Restraints :: Seat Belt — 7Srs Air Bag - Precautions. Preparation — 1Srs Air Bag - Collision Diagnosis — 1Srs Air Bag - Occupant Classification System — 1Srs Air Bag Control System - Precautions — 1Srs Air Bag Control System - System — 1Srs Air Bag Control System - Diagnosis Sensor Unit — 1Srs Air Bag Control System - Inspection and Adjustment — 1Ventilation, Heater & Air Conditioner :: Ventilation System — 6Heater & Air Conditioning System - Precautions — 1Heater & Air Conditioning System - Preparation — 1Heater & Air Conditioning System - Component Parts — 1Heater & Air Conditioning System - Diagnosis and Repair Work Flow — 1Heater & Air Conditioning System - Compressor — 1Heater & Air Conditioning System - Cooler Pipe and Hose — 1Heater & Air Conditioning System - Condenser. Condenser — 1Heater & Air Conditioning System - Heating and Cooling Unit Assembly — 1Heater & Air Conditioning System - Service Data and Specifications (SDS) — 1Heater & Air Conditioning Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1Heater & Air Conditioning Control System - Ecu Diagnosis Information — 1Heater & Air Conditioning Control System - Basic Inspection — 1Heater & Air Conditioning Control System - Dtc/circuit Diagnosis — 1Heater & Air Conditioning Control System - Symptom Diagnosis — 1Heater & Air Conditioning Control System - Removal and Installation — 1Body Interior :: Interior — 8Instrument Panel - Precautions. Preparation. Clip List — 1Instrument Panel - Squeak and Rattle Trouble Diagnoses — 1Instrument Panel - Cluster Lid C — 1Seat - Precautions — 1Seat - Preparation. Clip List — 1Seat - Component Parts — 1Seat - System — 1Seat - Diagnosis and Repair Work Flow — 1Seat - Front Seat — 1Seat - Second Row Seats — 1Seat - Third Row Seats — 1Seat - Front Seat — 1Seat - Second Row Seat — 1Seat - Third Row Seat — 1Automatic Drive Positioner - Precautions. Preparation — 1Automatic Drive Positioner - System — 1Automatic Drive Positioner - Diagnosis and Repair Work Flow — 1Automatic Drive Positioner - Inspection and Adjustment — 1Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock — 38Security Control System - Precautions — 1Security Control System - System — 1Security Control System - Ecm, Bcm, Intelligent Key Unit, Ipdm E/r — 1Security Control System - Vehicle Security System Cannot Be Set — 1Glass & Window System - Precautions. Preparation — 1Glass & Window System - Squeak and Rattle Trouble Diagnoses — 1Power Window Control System - Precautions. Preparation — 1Power Window Control System - Power Supply and Ground Circuit — 1Power Window Control System - Power Window Motor Circuit — 1Power Window Control System - Front Power Window Rh Alone Does Not Operate — 1Power Window Control System - Rear Lh Side Power Window Alone Does Not Operate — 1Power Window Control System - Rear Rh Side Power Window Alone Does Not Operate — 1Roof - Precautions. Preparation — 1Roof - Power Supply and Ground Circuit — 1Roof - Moonroof Switch Assembly — 1Roof - Lin Communication Circuit — 1Roof - Auto Operation Does Not Operate — 1Roof - Anti-Pinch Function Does Not Operate — 1Exterior - Precautions. Preparation. Clip List (Preparation) — 1Exterior - Squeak and Rattle Trouble Diagnoses — 1Exterior - Fender Protector — 1Exterior - Over Fender — 1Exterior - Under Cover — 1Exterior - Roof Side Rail — 1Body Repair - Service Information — 1Service Information - Sheet Metal Work ++ — 1Service Information - Body Welding and Precautions ++ — 1Service Information - Safety and Health ++ — 1Service Information - Repairing Procedures and Precautions ++ — 1Body Repair - Precaution — 1Body Repair - Preparation — 1Body Repair - Removal and Installation — 1Driver Controls :: Mirrors — 8Exterior Lighting System - System Description — 1System Description - Component Parts ++ — 1Exterior Lighting System - Basic Inspection — 1Exterior Lighting System - Dtc/circuit Diagnosis — 1Exterior Lighting System - Symptom Diagnosis — 1Exterior Lighting System - Periodic Maintenance — 1Exterior Lighting System - Removal and Installation — 1Interior Lighting System - Precautions. Preparation — 1Interior Lighting System - Component Parts. Interior Lighting System — 1Interior Lighting System - System — 1Interior Lighting System - Diagnosis and Repair Work Flow — 1Interior Lighting System - Interior Lighting System Symptoms (Symptom Diagnosis). Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Interior Lighting System - Foot Lamp — 1Wiper & Washer - Precautions — 1Wiper & Washer - Preparation. Bcm, Ipdm E/r (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Wiper & Washer - System — 1Wiper & Washer - Diagnosis and Repair Work Flow — 1Defogger - Precautions. Bcm, A/c Auto Amp. (Ecu Diagnosis Information) — 1Defogger - Diagnosis and Repair Work Flow — 1Horn - Precautions — 1Electrical & Power Control :: Power Outlet — 13Body Control System - Precautions. Preparation — 1Body Control System - Component Parts — 1Body Control System - System — 1Body Control System - Diagnosis System (bcm) — 1Body Control System - Bcm — 1Lan System - System Description — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - Removal and Installation — 1Charging System - Precautions. Preparation. Ecm, Ipdm E/r (Ecu Diagnosis Information) — 1Charging System - Diagnosis and Repair Work Flow — 1Charging System - Charging System (Symptom Diagnosis). Generator (Removal and Installation). Service Data and Specifications (SDS) — 1Power Supply, Ground & Circuit Elements - Precautions. Preparation. Service Data and Specifications (SDS) — 1Driver Information & Multimedia :: Meter, Warning Lamp & Indicator — 25Warning Chime System - Application Notice (How to Use This Manual). Precautions — 1Warning Chime System - System — 1Warning Chime System - Diagnosis System (combination Meter) — 1Warning Chime System - Bcm, Combination Meter (Ecu Diagnosis Information). Diagnosis and Repair Work Flow (Basic Inspection) — 1Sonar System - Precautions. Preparation — 1Sonar System - Sonar Control Unit — 1Dtc/circuit Diagnosis - B2720 Corner Sensor [rl] ++ — 1Audio, Visual & Navigation System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Multi Av (av Control Unit) ++ — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Symptom Diagnosis - Multi Av System ++ — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Cruise Control & Driver Assistance :: Cruise Control System — 17Driver Assistance System - System Description — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Driver Assistance System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1System Description - Handling Precaution ++ — 1Driver Assistance System - Ecu Diagnosis Information — 1Driver Assistance System - Basic Inspection — 1Basic Inspection - Distance Sensor Alignment ++ — 1Basic Inspection - Camera Aiming Adjustment ++ — 1Basic Inspection - Action Test ++ — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Laser/radar (distance Sensor) ++ — 1Dtc/circuit Diagnosis - Lane Camera (front Camera Unit) ++ — 1Driver Assistance System - Symptom Diagnosis — 1Driver Assistance System - Removal and Installation — 1Driver Assistance System - System Description — 1System Description - System ++ — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Drive Mode System - Precautions — 1Drive Mode System - Component Parts. Drive Mode System — 1Drive Mode System - System — 1Drive Mode System - Diagnosis and Repair Work Flow — 1Drive Mode System - Drive Mode Select Switch Circuit — 1Maintenance - Precautions. Preparation — 1Maintenance - General Maintenance — 1Maintenance - Periodic Maintenance — 1Maintenance - Recommended Fluids and Lubricants — 1Maintenance - Engine Maintenance — 1Maintenance - Chassis and Body Maintenance — 1Engine Lubrication System - Periodic Maintenance — 1Engine Lubrication System - Removal and Installation — 1Engine Cooling System - System Description — 1Engine Cooling System - Removal and Installation — 1Engine Control System - Vq35dd — 1Fuel System - Removal and Installation — 1Starting System - System Description — 1Starting System - Dtc/circuit Diagnosis — 1Driveline - Transfer: Ty92b — 1Driveline - Rear Propeller Shaft: 3fcj-Cvj — 1Driveline - Rear Final Drive: R145 — 1Front Axle - Periodic Maintenance — 1Front Axle - Removal and Installation — 1Rear Axle - Periodic Maintenance — 1Rear Axle - Removal and Installation — 1Rear Suspension - Removal and Installation — 1Road Wheels & Tires - System Description — 1Road Wheels & Tires - Basic Inspection — 1Road Wheels & Tires - Dtc/circuit Diagnosis — 1Road Wheels & Tires - Symptom Diagnosis — 1Road Wheels & Tires - Periodic Maintenance — 1Road Wheels & Tires - Removal and Installation — 1Parking Brake System - System Description — 1Parking Brake System - Basic Inspection — 1Parking Brake System - Dtc/circuit Diagnosis — 1Parking Brake System - Symptom Diagnosis — 1Parking Brake System - Removal and Installation — 1Brake Control System - Vdc/tcs/abs — 1Brake Control System - Automatic Brake Hold — 1Brake Control System - Automatic Emergency Braking — 1Brake Control System - Rear Automatic Braking — 1Steering Control System - System Description — 1Steering Control System - Basic Inspection — 1Steering Control System - Dtc/circuit Diagnosis — 1Steering Control System - Symptom Diagnosis — 1Srs Air Bag - Removal and Installation — 1Srs Air Bag Control System - System Description — 1Srs Air Bag Control System - Basic Inspection — 1Srs Air Bag Control System - Symptom Diagnosis — 1Heater & Air Conditioning System - Symptom Diagnosis — 1Heater & Air Conditioning System - Periodic Maintenance — 1Heater & Air Conditioning Control System - Automatic Air Conditioning — 1Instrument Panel - Removal and Installation — 1Instrument Panel - Unit Disassembly and Assembly — 1Seat - Ecu Diagnosis Information — 1Seat - Dtc/circuit Diagnosis — 1Seat - Symptom Diagnosis — 1Automatic Drive Positioner - System Description — 1Automatic Drive Positioner - Ecu Diagnosis Information — 1Automatic Drive Positioner - Dtc/circuit Diagnosis — 1Automatic Drive Positioner - Symptom Diagnosis — 1Automatic Drive Positioner - Removal and Installation — 1Security Control System - System Description — 1Security Control System - Basic Inspection — 1Security Control System - Dtc/circuit Diagnosis — 1Security Control System - Symptom Diagnosis — 1Security Control System - Removal and Installation — 1Glass & Window System - Removal and Installation — 1Power Window Control System - System Description — 1Power Window Control System - Ecu Diagnosis Information — 1Power Window Control System - Basic Inspection — 1Power Window Control System - Dtc/circuit Diagnosis — 1Power Window Control System - Symptom Diagnosis — 1Power Window Control System - Removal and Installation — 1Roof - System Description — 1Roof - Ecu Diagnosis Information — 1Roof - Basic Inspection — 1Roof - Dtc/circuit Diagnosis — 1Roof - Symptom Diagnosis — 1Roof - Removal and Installation — 1Exterior - System Description — 1Exterior - Removal and Installation — 1Body Repair - Repair Information — 1Exterior Lighting System - Led Headlamp — 1Interior Lighting System - Dtc/circuit Diagnosis — 1Interior Lighting System - Removal and Installation — 1Wiper & Washer - System Description — 1Wiper & Washer - Dtc/circuit Diagnosis — 1Wiper & Washer - Symptom Diagnosis — 1Wiper & Washer - Removal and Installation — 1Defogger - System Description — 1Defogger - Dtc/circuit Diagnosis — 1Defogger - Symptom Diagnosis — 1Defogger - Removal and Installation — 1Horn - Removal and Installation — 1Body Control System - Basic Inspection — 1Body Control System - Dtc/circuit Diagnosis — 1Body Control System - Symptom Diagnosis — 1Body Control System - Removal and Installation — 1Lan System - Can Fundamental — 1Lan System - Can — 1Lan System - Can Gateway — 1Power Control System - Ipdm E/r — 1Power Control System - Power Distribution System — 1Charging System - System Description — 1Charging System - Dtc/circuit Diagnosis — 1Power Supply, Ground & Circuit Elements - System Description — 1Power Supply, Ground & Circuit Elements - Basic Inspection — 1Power Supply, Ground & Circuit Elements - Removal and Installation — 1Warning Chime System - System Description — 1Warning Chime System - Dtc/circuit Diagnosis — 1Warning Chime System - Symptom Diagnosis — 1Sonar System - System Description — 1Sonar System - Basic Inspection — 1Sonar System - Dtc/circuit Diagnosis — 1Sonar System - Symptom Diagnosis — 1Sonar System - Removal and Installation — 1Audio, Visual & Navigation System - Nissanconnect — 1Audio, Visual & Navigation System - Intelligent Around View Monitor System — 1Audio, Visual & Navigation System - Rear View Monitor System — 1Audio, Visual & Navigation System - Telematics System — 1Driver Assistance System - Adas Control Unit 2 — 1Driver Assistance System - Driver Assistance System — 1Driver Assistance System - Chassis Control — 1Drive Mode System - Removal and Installation — 1Dtc/circuit Diagnosis (C053c Wheel Speed Sensor ... U2141 Can Comm Circuit) — 1Dtc/circuit Diagnosis (P0011 Intake Valve Timing Control ... P0111 Iat Sensor) — 1Dtc/circuit Diagnosis (P0116 Engine Coolant Temperature Sensor ... P025b Fuel Pump Module a) — 1Dtc/circuit Diagnosis (P026b Injection Timing ... P0420 Three Way Catalyst Function) — 1Dtc/circuit Diagnosis (P0441 Evap Control System ... P0524 Engine Oil Pressure) — 1Dtc/circuit Diagnosis (P0532 A/c Refrigerant Pressure Sensor ... P064d Ecm) — 1Dtc/circuit Diagnosis (P06da Engine Oil Pressure Control Solenoid Valve ... P1217 Engine Over Temperature) — 1Dtc/circuit Diagnosis (P1220 Fuel Pump Control Module (fpcm) ... P1574 Ascd Vehicle Speed Sensor) — 1Dtc/circuit Diagnosis (P1575 Brake Switch ... P2101 Electric Throttle Control Function) — 1Dtc/circuit Diagnosis (P2118 Throttle Control Motor ... P34ac Electric Intake Valve Timing Control Actuator) — 1Dtc/circuit Diagnosis (Active Grille Shutter ... High Pressure Fuel Pump) — 1Dtc/circuit Diagnosis (Ignition Signal ... Variable Induction Air System) — 14012 C1040 Emergency Brake — 14013 C106a Wheel Sensor — 14014 C1078-55 Not Configuration — 14015 C10b4-98 Overheat — 14016 B1001 Lap Pre-Tensioner Lh — 14017 B0001 Driver Air Bag Module — 14018 B100e Knee Air Bag Module Rh — 14019 B142x Collision Detection — 1Dtc/circuit Diagnosis (B20c7-11 A/c Clutch ... B24a6-11 in-Vehicle Sensor) — 1Dtc/circuit Diagnosis (B24a6-15 in-Vehicle Sensor ... U2140-87 Can Comm Err (ecm)) — 1Dtc/circuit Diagnosis (C1f00-1c Control Unit ... C1f04-61 Brake Sw/stop Lamp Sw) — 1Dtc/circuit Diagnosis (C1f05-49 Front Camera Unit ... C1f70-87 Ethernet Circuit) — 1
108steps
~648min
5/5difficulty
Done 0 of 108
  • P0532 A/c Refrigerant Pressure Sensor
  • P055f Engine Oil Pressure
  • P0573 Brake Pedal Switch a
  • P059f Active Grille Shutter
  • P0606 Ecm
  • P0611 Ecm Protection
  • P062b Ecm
  • P062f Control Module
  • P0643 Sensor Power Supply
  • P064d Ecm

P0532 A/c Refrigerant Pressure Sensor Nissan Pathfinder R53

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis name)
DTC detecting condition
P0532 00

REFRIGERANT PRESS SENSOR A

(A/C refrigerant pressure sensor A circuit low)
Diagnosis condition
  • Ignition switch ON

  • Engine running

Signal (terminal) Refrigerant pressure sensor signal
Threshold ECM detects that input signal from the refrigerant pressure sensor is out of the specified range.
Diagnosis delay time 5 seconds or more

POSSIBLE CAUSE

  • Harness or connectors

  • Refrigerant pressure sensor

FAIL-SAFE

Not applicable

Confirmation Procedure

PRECONDITIONING-1

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 11 V or more under ignition switch OFF condition.

>>

GO TO 2.

PRECONDITIONING-2

Check the following conditions:

Ambient temperature 0 °C or more

Is the condition satisfied?

YES>>

GO TO 3.

NO>>
  1. Satisfy the condition.

  2. GO TO 3.

PERFORM COMPONENT FUNCTION CHECK

Perform component function check. Refer to Component Function Check.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Proceed to DTC Diagnosis Procedure.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and warm it up to normal operating temperature.

  2. Hold Nissan Pathfinder vehicle speed at more than 40 km/h for 180 consecutive seconds.

  3. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO>>

INSPECTION END

DTC Diagnosis Procedure

CHECK REFRIGERANT PRESSURE SENSOR

Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace refrigerant pressure sensor.

P055f Engine Oil Pressure Nissan Pathfinder 2022

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P055F

Engine oil pressure

(Engine oil pressure out of range)
Diagnosis condition
  • After ECM self shut-off.

  • Engine oil temperature is more than -10 °C (14 °F).

Signal (terminal) Engine oil pressure sensor signal
Threshold When the engine oil pressure is higher than normal value at stop engine.
Diagnosis delay time 3.5 seconds

POSSIBLE CAUSE

  • Harness or connectors (Engine oil pressure sensor, engine oil temperature sensor or crankshaft position sensor circuit is open or shorted.)

  • Engine oil pressure sensor

  • Engine oil temperature sensor

  • Engine oil pressure control solenoid valve

  • Crankshaft position sensor

  • Oil pump

  • Clogging in oil line

  • Amount of engine oil

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON and wait at least 30 seconds.

  2. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P055F is displayed with other DTC, first perform the trouble diagnosis for other DTC.

Is other DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2.

CHECK HARNESS CONNECTOR

  1. Disconnect following sensors harness connector and ECM harness connector.

    • Engine oil pressure sensor

    • Engine oil temperature sensor

    • Crankshaft position sensor

  2. Connect following sensors harness connector and ECM harness connector.

    • Engine oil pressure sensor

    • Engine oil temperature sensor

    • Crankshaft position sensor

  3. Perform DTC Confirmation Procedure. Refer to DTC Description.

Is DTC detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK ENGINE OIL LEVEL AND LEAKAGE

  1. Turn ignition switch OFF.

  2. Check engine oil level and leakage. Refer to Inspection.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts.

CHECK OIL PUMP

Visually check oil pump and listen to operation sound.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace error-detected parts.

CHECK ENGINE OIL PRESSURE

With CONSULT

  1. Turn ignition switch ON.

  2. On CONSULT screen, select “ENGINE”>>“Data Monitor”.

  3. Start the engine and check that “EOP SENSOR” changes, according to engine speeds.

    Monitor itemConditionValue
    EOP SENSOR
    • Engine: After warming up

    • Selector lever: P or N

    • Air conditioner switch: OFF

    • No load

    Idle 1.570 – 1.900 V
    2,000 rpm 1.610 – 2.120 V

Without CONSULT

Check engine oil pressure. Refer to Inspection.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Change engine oil. Refer to Draining and Refilling.

P0573 Brake Pedal Switch a Nissan Pathfinder SUV

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0573 00

Brake pedal switch A

(Brake Switch "A" Circuit High)
Diagnosis condition
  • When a deceleration G of -0.13 G or more occurs after the Nissan Pathfinder vehicle speed exceeds 30 km/h.

  • When the brake normal open switch [Stop lamp switch (BCM)] is pressed.

Signal (terminal) Brake pedal position switch signal
Threshold Brake pedal position switch is released until 2 seconds have passed after the Nissan Pathfinder vehicle has stopped when the diagnosis condition is established. Malfunction is confirmed when the above condition is established 5 times.
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors

    (Brake pedal position switch circuit is close.)

  • Brake pedal position switch

FAIL-SAFE

Not applicable

CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC P0573 is displayed with DTC P0605, first perform the confirmation procedure (trouble diagnosis) for DTC P0605.

Is DTC P0605 detected?

YES>>

Perform diagnosis for P0605. Refer to Diagnosis Procedure.

NO>>

GO TO 2.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TEST CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 11 V at ignition switch ON.

>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON and wait at least 2 seconds.

  2. Repeat the following step 5 times.

    1. Drive the Nissan Pathfinder vehicle and accelerate to 48 km/h.

    2. Decelerate from 48 km/h to 0 km/h within 7 seconds.

    3. Stop the Nissan Pathfinder vehicle for 2 seconds or more.

  3. Check DTC.

Is DTC P0573 detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P1572 is displayed with other DTC, first perform the trouble diagnosis for other DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2.

CHECK OVERALL FUNCTION-1

With CONSULT

  1. Turn ignition switch ON.

  2. Select “BRAKE SW1” and “BRAKE SW2” in “DATA MONITOR” mode of “ENGINE” using CONSULT.

  3. Check “BRAKE SW1” and “BRAKE SW2” indication as per the following conditions.

    Monitor itemConditionIndication
    BRAKE SW1 Brake pedal Slightly depressed OFF
    Fully released ON
    BRAKE SW2 Brake pedal Slightly depressed ON
    Fully released OFF

Without CONSULT

  1. Turn ignition switch ON.

  2. Check the voltage between ECM harness connector terminals as per the following.

    ECMCondition

    Voltage

    (Approx.)
    Connector+–
    Terminal
    E32 192 204 Brake pedal Slightly depressed 0 V
    Fully released Battery voltage

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 4.

CHECK STOP LAMP SWITCH POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect stop lamp switch harness connector.

  3. Check the voltage between stop lamp switch harness connector and ground.

    +−Voltage
    Stop lamp switch
    ConnectorTerminal
    E38 1 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Perform the trouble diagnosis for power supply circuit.

CHECK STOP LAMP SWITCH

Check the stop lamp switch. Refer toComponent Inspection .

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Replace stop lamp switch. Refer to Exploded View.

CHECK STOP LAMP SWITCH SIGNAL CIRCUIT

  1. Disconnect BCM harness connector.

  2. Check the continuity between stop lamp switch harness connector and ECM harness connector.

    +−Continuity
    Stop lamp switchBCM
    ConnectorTerminalConnectorTerminal
    E38 2 M80 110 Existed
  3. Also check harness for short to ground and to power.

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

GO TO 6.

REPLACE ECM

Replace ECM. Refer to Removal and Installation.

>>

INSPECTION END

P059f Active Grille Shutter Nissan Pathfinder Fifth generation

DTC Description

DTC DETECTION LOGIC

Active grille shutter normally stops within zone which is defined by zone (90°±10°).

If the active grille shutter stops within zone stuck error is detected, and if the active grille shutter stops at position beyond zone overrun error is detected.

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P059F 00

ACTIVE GRILLE AIR SHUTTER A

(Active grille air shutter A performance/stuck off)
Diagnosis condition —
Signal (terminal) Active grille shutter communication signal
Threshold Detects the malfunction of initial position learning or operational malfunctions for specified times.
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors

    (Active grille shutter circuit is open or shorted.)

  • Active grille shutter

  • Foreign objects interferes with active grille shutter

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

CHECK DTC PRIORITY

If DTC P059F is displayed with other DTC, first perform the trouble diagnosis for other DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2.

PERFORM DIAGNOSIS PROCEDURE

>>

Refer to DTC Diagnosis Procedure.

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P059F is displayed with other DTC, first perform the trouble diagnosis for other DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2.

CHECK ACTIVE GRILL SHUTTER

  1. Turn ignition switch OFF.

  2. Check if any foreign objects interferes with active grille shutter.

  3. Check the installation condition of active grille shutter.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace the error-detected parts.

CHECK ACTIVE GRILLE SHUTTER POWER SUPPLY

  1. Disconnect active grille shutter harness connector.

  2. Check the voltage between active grille shutter harness connector and ground as follows.

    +−Condition

    Voltage

    (Approx.)
    Active grille shutter
    ConnectorTerminal
    E202 1 Ground Ignition switch: ON Battery voltage
    Ignition switch: OFF 0 V

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

GO TO 4.

CHECK ACTIVE GRILLE SHUTTER POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF

  2. Disconnect IPDM E/R harness connector.

  3. Check the continuity between active grille shutter harness connector and IPDM E/R harness connector.

    Active grille shutterIPDM E/RContinuity
    ConnectorTerminalConnectorTerminal
    E202 1 E120 8 Existed

Is the inspection result normal?

YES>>

Perform trouble diagnosis for power supply circuit.

NO>>

Repair or replace the error-detected parts.

CHECK ACTIVE GRILLE SHUTTER GROUND CIRCUIT

  1. Turn ignition switch OFF

  2. Check the continuity between active grille shutter harness connector and ground.

    Active grille shutter−Continuity
    ConnectorTerminal
    E202 4 Ground Existed
  3. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair open circuit, short to ground or short to power in harness or connectors.

CHECK ACTIVE GRILLE SHUTTER INPUT SIGNAL CIRCUIT

  1. Disconnect ECM harness connector.

  2. Check the continuity between ECM harness connector and active grille shutter harness connector.

+–Continuity
ECMActive grille shutter
ConnectorTerminalConnectorTerminal
F79 167 E202 3 Existed

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair or replace the error-detected parts.

CHECK ACTIVE GRILLE SHUTTER

Check active grille shutter. Refer to Component Inspection.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace active grille shutter. Refer to Removal and Installation.

P0606 Ecm Nissan Pathfinder 2022

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0606 00

CONTROL MODULE

(Control module processor)
Diagnosis condition —
Signal (terminal) —
Threshold Malfunction in ECM processor
Diagnosis delay time —

POSSIBLE CAUSE

ECM

FAIL-SAFE

Fail safe modeNissan Pathfinder Vehicle behavior
Device fix mode
  • Fixes electric intake valve timing control motor in the reference position.

  • Fixes exhaust valve timing control solenoid valve in the reference position.

Electric throttle control cancel mode ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed opening (approx. 5 degrees) by the return spring.

DTC Confirmation Procedure

PRECONDITIONING

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 11 V or more with ignition switch ON.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE-I

  1. Turn ignition switch ON (engine stopped) and wait at least 10 seconds.

  2. Turn ignition switch OFF and wait at least 10 seconds.

  3. Turn ignition switch ON.

  4. Check 1st trip DTC.

Is DTC P0606 detected?

YES>>

Proceed to Diagnosis Procedure.

NO>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE-II

  1. Start engine.

  2. Rev up the engine quickly to approximately 3,000 rpm under unloaded condition and completely release the accelerator pedal.

  3. Let the engine idle and wait at least 10 seconds.

  4. Turn ignition switch OFF and wait at least 10 seconds.

  5. Turn ignition switch ON.

  6. Check 1st trip DTC.

Is DTC P0606 detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure for 3 times. Refer to DTC Description.

Is the DTC P0606 displayed again?

YES>>

Replace ECM. Refer to Removal and Installation.

NO>>

INSPECTION END

P0611 Ecm Protection Nissan Pathfinder R53

DTC Description

This DTC is detected when the ECM protective function is activated due to an extreme temperature increase in ECM, resulting from severe conditions such as heavy load driving.

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0611 00

FIC MODULE

(Fuel Injector Control Module Performance)
Diagnosis condition —
Signal (terminal) —
Threshold ECM overheat protection control is activated
Diagnosis delay time —

POSSIBLE CAUSE

ECM overheating

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

This DTC is displayed as protection function history. If no malfunction is detected after the diagnosis, the customer must be informed of the activation of the protection function.

>>

Refer to DTC Diagnosis Procedure.

DTC Diagnosis Procedure

INSPECTION START

  1. Perform DTC P0605 confirmation procedure. Refer to DTC Description.

  2. Check 1st trip DTC.

Is the 1st trip DTC P0605 detected?

YES>>

Refer to DTC Description.

NO>>

Explain the customer about the activation of the protection function.

P062b Ecm Nissan Pathfinder 5th Gen

DTC Description

When the malfunction occurs in the fuel injector driver circuit, DTC is detected.

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P062B 00

ECM

(Internal control module fuel injector control performance)
Diagnosis condition Engine running at idle
Signal (terminal) —
Threshold Injector driver unit is malfunctioning
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness and connectors (Injector circuit is open or shorted)

  • Battery power supply

  • ECM (injector driver unit)

  • Fuel injector relay

FAIL-SAFE

Fail safe modeNissan Pathfinder Vehicle behavior
Traveling control mode Accelerator angle variation control

ECM controls the accelerator pedal depression speed to make it slower than actual speed. This causes a drop in accelerating performance and encourages the driver to repair malfunction.

Device fix mode
  • Fixes electric intake valve timing control motor in the reference position.

  • Fixes exhaust valve timing control solenoid valve in the reference position.

Combustion control mode Stratified charge combustion control at starting No stratified charge combustion at starting (cold start).

DTC Confirmation Procedure

PRECONDITIONING

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine and keep the engine speed at idle for 30 seconds.

  2. Check 1st trip DTC.

Is DTC P062B detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK FUEL INJECTOR DRIVER CIRCUIT

Check ECM (Injector driver unit), relay, connector and harness for error or abnormality. Refer to Component Function Check.

Is inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

  4. Check 1st trip DTC.

Is the DTC P062B displayed again?

YES>>

Replace ECM. Refer to Removal and Installation.

NO>>

INSPECTION END

P062f Control Module Nissan Pathfinder

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P062F 00

CONTROL MODULE

(Internal control module EEPROM error)
Diagnosis condition Ignition switch ON
Signal (terminal) —
Threshold ECM calculation is function malfunctioning
Diagnosis delay time —

POSSIBLE CAUSE

ECM

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following

procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is between 11 V or more with ignition switch ON.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON and wait at least 1 second.

  2. Turn ignition switch OFF and wait at least 10 seconds.

  3. Repeat step 1 and 2 for 10 times.

  4. Erase DTC.

  5. Turn ignition switch OFF and wait at least 10 seconds.

  6. Turn ignition switch ON.

  7. Check the DTC.

Is DTC P062F detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

INSPECTION START

  1. Turn ignition switch ON and wait at least 1 second.

  2. Turn ignition switch OFF and wait at least 10 seconds.

  3. Repeat step 1 and 2 for 10 times.

  4. Erase DTC.

  5. Turn ignition switch OFF and wait at least 10 seconds.

  6. Turn ignition switch ON.

  7. Check the DTC.

Is DTC erased?

YES>>

INSPECTION END

NO>>

GO TO 2.

REPLACE ECM

  1. Replace ECM. Refer to Removal and Installation.

  2. Perform Description.

>>

INSPECTION END

P0643 Sensor Power Supply Nissan Pathfinder R53

DTC Description

ECM supplies a voltage of 5 V to some of the sensors systematically divided into 3 groups, respectively. Accordingly, when a short circuit develops in a sensor power source, a malfunction may occur simultaneously in the sensors belonging to the same group as the short-circuited sensor.

Sensor power supply 1

  • APP sensor 1

  • Crankshaft position sensor 1

  • Exhaust camshaft position sensor (bank 1)

  • Throttle position sensor

  • Mass air flow sensor

  • Intake camshaft position sensor (bank 1)

  • Engine oil pressure sensor

Sensor power supply 2

  • APP sensor 2

  • Intake camshaft position sensor (bank2)

  • Refrigerant pressure sensor

  • Crankshaft position sensor 2

  • Exhaust camshaft position sensor (bank 2)

  • Fuel rail pressure sensor

Sensor power supply 3

  • EVAP control system pressure sensor

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0643 00

SENSOR POWER/CIRC

(Sensor power supply 1 circuit short)
Diagnosis condition Engine running at idle
Signal (terminal) Sensor power supply 1 signal
Threshold A voltage of power source for sensor is excessively low or high
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors

    • Crankshaft position sensor 1 is shorted.

    • Exhaust camshaft position sensor (bank 1) is shorted.

    • Throttle position sensor is shorted.

    • Mass air flow sensor is shorted.

    • Accelerator pedal position sensor 1 is shorted.

    • Intake camshaft position sensor (bank 1) is shorted.

    • Engine oil pressure sensor is shorted.

  • Crankshaft position sensor 1

  • Exhaust camshaft position sensor (bank 1)

  • Throttle position sensor

  • Mass air flow sensor

  • Accelerator pedal position sensor 1

  • Intake camshaft position sensor (bank 1)

  • Engine oil pressure sensor

FAIL-SAFE

Fail safe modeNissan Pathfinder Vehicle behavior
Device fix mode
  • Fixes electric intake valve timing control motor in the reference position.

  • Fixes exhaust valve timing control solenoid valve in the reference position.

Electric throttle control cancel mode ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed opening (approx. 5 degrees) by the return spring.

DTC Confirmation Procedure

PRECONDITIONING

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 11 V or more with ignition switch ON.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON and wait at least 10 second.

  2. Turn ignition switch OFF and wait at least 10 seconds.

  3. Repeat step 1 and 2 for 2 times.

  4. Turn ignition switch ON.

  5. Check the DTC.

Is the DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK ECM POWER SUPPLY AND GROUND CIRCUIT

Perform trouble diagnosis for ECM power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts.

CHECK ACCELERATOR PEDAL POSITION SENSOR 1 POWER SUPPLY CIRCUIT

  1. Disconnect accelerator pedal position (APP) sensor harness connector.

  2. Turn ignition switch ON.

  3. Check the voltage between APP sensor harness connector and ground.

    +-

    Voltage

    (Approx.)
    APP sensor
    ConnectorTerminal
    E31 4 Ground 5 V

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

GO TO 3.

CHECK SENSOR POWER SUPPLY CIRCUITS

Check harness for short to power and short to ground, between the following terminals.

ECMSensor
ConnectorTerminalNameConnectorTerminal
F78 38 Exhaust camshaft position sensor (bank 1) F43 1
39 Crankshaft position sensor 1 F11 1
40 Intake camshaft position sensor (bank 1) F113 1
41 Mass air flow sensor E64 1
42 Engine oil pressure sensor F54 3
F79 129 Electric throttle control actuator F50 5
E32 198 APP sensor 1 E31 4

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair short to ground or short to power in harness or connectors.

CHECK COMPONENTS

Check the following.

  • Crankshaft position sensor 1 (Refer to Component Inspection.)

  • Exhaust camshaft position sensor (bank1) (Refer to Component Inspection.)

  • TP sensor (Refer to Component Inspection (Throttle Position Sensor).)

  • Mass air flow sensor (Refer to Component Inspection (Mass Air Flow Sensor).)

  • Intake camshaft position sensor (bank 1) (Refer to Component Inspection.)

  • Engine oil pressure sensor (Refer to Component Inspection.)

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace malfunctioning component.

CHECK APP SENSOR

Refer to Component Inspection (Accelerator Pedal Position Sensor).

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Replace accelerator pedal assembly. Refer to Removal and Installation.

CHECK INTERMITTENT INCIDENT

Check intermittent incident. Refer to Intermittent Incident.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair or replace error-detected parts.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure. Refer to DTC Confirmation Procedure.

Is the 1st trip DTC P0643 displayed again?

YES>>

Replace ECM. Refer to Removal and Installation.

NO>>

INSPECTION END

P064d Ecm Nissan Pathfinder SUV

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detecting condition
P064D 00

Internal control module

(Internal Control Module O2 Sensor Processor Performance Bank 1)
Diagnosis condition -
Signal (terminal) A/F sensor 1 (bank 1) signal
Threshold ECM communication error
Diagnosis delay time 1 sec

POSSIBLE CAUSE

ECM

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the turn ignition switch OFF and wait at least 10 seconds before conducting the next test.

YES>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

Start the engine.

Is DTC P064D detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

REPLACE ECM

Replace ECM. Refer to Removal and Installation.

YES>>

INSPECTION END