4017 B0001 Driver Air Bag Module

In this manual: 4017 B0001 Driver Air Bag Module
General Information — 8Engine :: Engine Mechanical — 19Engine Lubrication System - Precautions. Preparation — 1Engine Lubrication System - Lubrication System (System Description). Engine Oil Pressure (Basic Inspection). Service Data and Specifications (SDS) — 1Engine Cooling System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Engine Cooling System - Engine Coolant — 1Engine Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Engine Control System - Ecu Diagnosis Information — 1Ecu Diagnosis Information - Ecm ++ — 1Engine Control System - Basic Inspection — 1Basic Inspection - Diagnosis and Repair Workflow ++ — 1Basic Inspection - Basic Inspection ++ — 1Basic Inspection - Additional Service When Replacing Ecm ++ — 1Basic Inspection - Fuel Pressure Check ++ — 1Basic Inspection - How to Set Srt Code ++ — 1Basic Inspection - How to Erase Permanent Dtc ++ — 1Engine Control System - Dtc/circuit Diagnosis — 1Engine Control System - Symptom Diagnosis — 1Engine Control System - Periodic Maintenance — 1Engine Control System - Removal and Installation — 1Fuel System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Fuel System - Fuel System (Periodic Maintenance). Fuel Level Sensor Unit (Disassembly and Assembly) — 1Exhaust System - Precautions. Preparation — 1Exhaust System - Exhaust System (Periodic Maintenance). Exhaust System (Removal and Installation) — 1Starting System - Precautions. Preparation. Starter Motor (Service Data and Specifications (sds)) — 1Starting System - Diagnosis and Repair Work Flow — 1Starting System - Starting System (Symptom Diagnosis). Starter Motor (Removal and Installation) — 1Accelerator Control System - Precautions. Service Data and Specifications (SDS) — 1Accelerator Control System - Accelerator Pedal Assembly — 1Transmission & Driveline :: Transaxle & Transmission — 21Driveline - System Description — 1Transfer: Ty92b - Ecu Diagnosis Information. Awd Control Unit ++ — 1Driveline - Basic Inspection — 1Driveline - Dtc/circuit Diagnosis — 1Driveline - Symptom Diagnosis — 1Driveline - Removal and Installation — 1Transfer: Ty92b - Unit Removal and Installation. Transfer Assembly ++ — 1Driveline - Unit Disassembly and Assembly — 1Driveline - Basic Inspection — 1Driveline - Removal and Installation — 1Driveline - Unit Disassembly and Assembly — 1Front Axle - Precautions. Preparation — 1Front Axle - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Front Axle - Front Drive Shaft Boot — 1Front Axle - Front Drive Shaft — 1Rear Axle - Precautions. Preparation. Service Data and Specifications (SDS) — 1Rear Axle - Noise, Vibration and Harshness (nvh) Troubleshooting — 1Rear Axle - Rear Drive Shaft — 1Suspension :: Front Suspension — 7Rear Suspension - Precautions. Preparation — 1Rear Suspension - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Rear Suspension - Rear Suspension Assembly — 1Road Wheels & Tires - Precautions — 1Road Wheels & Tires - Preparation. Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Road Wheels & Tires - System — 1Brakes :: Brake System — 9Parking Brake System - Precautions. Preparation — 1Parking Brake System - System — 1Vdc/tcs/abs - Precautions ++ — 1Brake Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Dtc/circuit Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Steering :: Steering System — 9Steering Control System - Precautions — 1Steering Control System - System — 1Steering Control System - Eps Control Unit (Ecu Diagnosis Information. Removal and Installation) — 1Restraints :: Seat Belt — 7Srs Air Bag - Precautions. Preparation — 1Srs Air Bag - Collision Diagnosis — 1Srs Air Bag - Occupant Classification System — 1Srs Air Bag Control System - Precautions — 1Srs Air Bag Control System - System — 1Srs Air Bag Control System - Diagnosis Sensor Unit — 1Srs Air Bag Control System - Inspection and Adjustment — 1Ventilation, Heater & Air Conditioner :: Ventilation System — 6Heater & Air Conditioning System - Precautions — 1Heater & Air Conditioning System - Preparation — 1Heater & Air Conditioning System - Component Parts — 1Heater & Air Conditioning System - Diagnosis and Repair Work Flow — 1Heater & Air Conditioning System - Compressor — 1Heater & Air Conditioning System - Cooler Pipe and Hose — 1Heater & Air Conditioning System - Condenser. Condenser — 1Heater & Air Conditioning System - Heating and Cooling Unit Assembly — 1Heater & Air Conditioning System - Service Data and Specifications (SDS) — 1Heater & Air Conditioning Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1Heater & Air Conditioning Control System - Ecu Diagnosis Information — 1Heater & Air Conditioning Control System - Basic Inspection — 1Heater & Air Conditioning Control System - Dtc/circuit Diagnosis — 1Heater & Air Conditioning Control System - Symptom Diagnosis — 1Heater & Air Conditioning Control System - Removal and Installation — 1Body Interior :: Interior — 8Instrument Panel - Precautions. Preparation. Clip List — 1Instrument Panel - Squeak and Rattle Trouble Diagnoses — 1Instrument Panel - Cluster Lid C — 1Seat - Precautions — 1Seat - Preparation. Clip List — 1Seat - Component Parts — 1Seat - System — 1Seat - Diagnosis and Repair Work Flow — 1Seat - Front Seat — 1Seat - Second Row Seats — 1Seat - Third Row Seats — 1Seat - Front Seat — 1Seat - Second Row Seat — 1Seat - Third Row Seat — 1Automatic Drive Positioner - Precautions. Preparation — 1Automatic Drive Positioner - System — 1Automatic Drive Positioner - Diagnosis and Repair Work Flow — 1Automatic Drive Positioner - Inspection and Adjustment — 1Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock — 38Security Control System - Precautions — 1Security Control System - System — 1Security Control System - Ecm, Bcm, Intelligent Key Unit, Ipdm E/r — 1Security Control System - Vehicle Security System Cannot Be Set — 1Glass & Window System - Precautions. Preparation — 1Glass & Window System - Squeak and Rattle Trouble Diagnoses — 1Power Window Control System - Precautions. Preparation — 1Power Window Control System - Power Supply and Ground Circuit — 1Power Window Control System - Power Window Motor Circuit — 1Power Window Control System - Front Power Window Rh Alone Does Not Operate — 1Power Window Control System - Rear Lh Side Power Window Alone Does Not Operate — 1Power Window Control System - Rear Rh Side Power Window Alone Does Not Operate — 1Roof - Precautions. Preparation — 1Roof - Power Supply and Ground Circuit — 1Roof - Moonroof Switch Assembly — 1Roof - Lin Communication Circuit — 1Roof - Auto Operation Does Not Operate — 1Roof - Anti-Pinch Function Does Not Operate — 1Exterior - Precautions. Preparation. Clip List (Preparation) — 1Exterior - Squeak and Rattle Trouble Diagnoses — 1Exterior - Fender Protector — 1Exterior - Over Fender — 1Exterior - Under Cover — 1Exterior - Roof Side Rail — 1Body Repair - Service Information — 1Service Information - Sheet Metal Work ++ — 1Service Information - Body Welding and Precautions ++ — 1Service Information - Safety and Health ++ — 1Service Information - Repairing Procedures and Precautions ++ — 1Body Repair - Precaution — 1Body Repair - Preparation — 1Body Repair - Removal and Installation — 1Driver Controls :: Mirrors — 8Exterior Lighting System - System Description — 1System Description - Component Parts ++ — 1Exterior Lighting System - Basic Inspection — 1Exterior Lighting System - Dtc/circuit Diagnosis — 1Exterior Lighting System - Symptom Diagnosis — 1Exterior Lighting System - Periodic Maintenance — 1Exterior Lighting System - Removal and Installation — 1Interior Lighting System - Precautions. Preparation — 1Interior Lighting System - Component Parts. Interior Lighting System — 1Interior Lighting System - System — 1Interior Lighting System - Diagnosis and Repair Work Flow — 1Interior Lighting System - Interior Lighting System Symptoms (Symptom Diagnosis). Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Interior Lighting System - Foot Lamp — 1Wiper & Washer - Precautions — 1Wiper & Washer - Preparation. Bcm, Ipdm E/r (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Wiper & Washer - System — 1Wiper & Washer - Diagnosis and Repair Work Flow — 1Defogger - Precautions. Bcm, A/c Auto Amp. (Ecu Diagnosis Information) — 1Defogger - Diagnosis and Repair Work Flow — 1Horn - Precautions — 1Electrical & Power Control :: Power Outlet — 13Body Control System - Precautions. Preparation — 1Body Control System - Component Parts — 1Body Control System - System — 1Body Control System - Diagnosis System (bcm) — 1Body Control System - Bcm — 1Lan System - System Description — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - Removal and Installation — 1Charging System - Precautions. Preparation. Ecm, Ipdm E/r (Ecu Diagnosis Information) — 1Charging System - Diagnosis and Repair Work Flow — 1Charging System - Charging System (Symptom Diagnosis). Generator (Removal and Installation). Service Data and Specifications (SDS) — 1Power Supply, Ground & Circuit Elements - Precautions. Preparation. Service Data and Specifications (SDS) — 1Driver Information & Multimedia :: Meter, Warning Lamp & Indicator — 25Warning Chime System - Application Notice (How to Use This Manual). Precautions — 1Warning Chime System - System — 1Warning Chime System - Diagnosis System (combination Meter) — 1Warning Chime System - Bcm, Combination Meter (Ecu Diagnosis Information). Diagnosis and Repair Work Flow (Basic Inspection) — 1Sonar System - Precautions. Preparation — 1Sonar System - Sonar Control Unit — 1Dtc/circuit Diagnosis - B2720 Corner Sensor [rl] ++ — 1Audio, Visual & Navigation System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Multi Av (av Control Unit) ++ — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Symptom Diagnosis - Multi Av System ++ — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Cruise Control & Driver Assistance :: Cruise Control System — 17Driver Assistance System - System Description — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Driver Assistance System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1System Description - Handling Precaution ++ — 1Driver Assistance System - Ecu Diagnosis Information — 1Driver Assistance System - Basic Inspection — 1Basic Inspection - Distance Sensor Alignment ++ — 1Basic Inspection - Camera Aiming Adjustment ++ — 1Basic Inspection - Action Test ++ — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Laser/radar (distance Sensor) ++ — 1Dtc/circuit Diagnosis - Lane Camera (front Camera Unit) ++ — 1Driver Assistance System - Symptom Diagnosis — 1Driver Assistance System - Removal and Installation — 1Driver Assistance System - System Description — 1System Description - System ++ — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Drive Mode System - Precautions — 1Drive Mode System - Component Parts. Drive Mode System — 1Drive Mode System - System — 1Drive Mode System - Diagnosis and Repair Work Flow — 1Drive Mode System - Drive Mode Select Switch Circuit — 1Maintenance - Precautions. Preparation — 1Maintenance - General Maintenance — 1Maintenance - Periodic Maintenance — 1Maintenance - Recommended Fluids and Lubricants — 1Maintenance - Engine Maintenance — 1Maintenance - Chassis and Body Maintenance — 1Engine Lubrication System - Periodic Maintenance — 1Engine Lubrication System - Removal and Installation — 1Engine Cooling System - System Description — 1Engine Cooling System - Removal and Installation — 1Engine Control System - Vq35dd — 1Fuel System - Removal and Installation — 1Starting System - System Description — 1Starting System - Dtc/circuit Diagnosis — 1Driveline - Transfer: Ty92b — 1Driveline - Rear Propeller Shaft: 3fcj-Cvj — 1Driveline - Rear Final Drive: R145 — 1Front Axle - Periodic Maintenance — 1Front Axle - Removal and Installation — 1Rear Axle - Periodic Maintenance — 1Rear Axle - Removal and Installation — 1Rear Suspension - Removal and Installation — 1Road Wheels & Tires - System Description — 1Road Wheels & Tires - Basic Inspection — 1Road Wheels & Tires - Dtc/circuit Diagnosis — 1Road Wheels & Tires - Symptom Diagnosis — 1Road Wheels & Tires - Periodic Maintenance — 1Road Wheels & Tires - Removal and Installation — 1Parking Brake System - System Description — 1Parking Brake System - Basic Inspection — 1Parking Brake System - Dtc/circuit Diagnosis — 1Parking Brake System - Symptom Diagnosis — 1Parking Brake System - Removal and Installation — 1Brake Control System - Vdc/tcs/abs — 1Brake Control System - Automatic Brake Hold — 1Brake Control System - Automatic Emergency Braking — 1Brake Control System - Rear Automatic Braking — 1Steering Control System - System Description — 1Steering Control System - Basic Inspection — 1Steering Control System - Dtc/circuit Diagnosis — 1Steering Control System - Symptom Diagnosis — 1Srs Air Bag - Removal and Installation — 1Srs Air Bag Control System - System Description — 1Srs Air Bag Control System - Basic Inspection — 1Srs Air Bag Control System - Symptom Diagnosis — 1Heater & Air Conditioning System - Symptom Diagnosis — 1Heater & Air Conditioning System - Periodic Maintenance — 1Heater & Air Conditioning Control System - Automatic Air Conditioning — 1Instrument Panel - Removal and Installation — 1Instrument Panel - Unit Disassembly and Assembly — 1Seat - Ecu Diagnosis Information — 1Seat - Dtc/circuit Diagnosis — 1Seat - Symptom Diagnosis — 1Automatic Drive Positioner - System Description — 1Automatic Drive Positioner - Ecu Diagnosis Information — 1Automatic Drive Positioner - Dtc/circuit Diagnosis — 1Automatic Drive Positioner - Symptom Diagnosis — 1Automatic Drive Positioner - Removal and Installation — 1Security Control System - System Description — 1Security Control System - Basic Inspection — 1Security Control System - Dtc/circuit Diagnosis — 1Security Control System - Symptom Diagnosis — 1Security Control System - Removal and Installation — 1Glass & Window System - Removal and Installation — 1Power Window Control System - System Description — 1Power Window Control System - Ecu Diagnosis Information — 1Power Window Control System - Basic Inspection — 1Power Window Control System - Dtc/circuit Diagnosis — 1Power Window Control System - Symptom Diagnosis — 1Power Window Control System - Removal and Installation — 1Roof - System Description — 1Roof - Ecu Diagnosis Information — 1Roof - Basic Inspection — 1Roof - Dtc/circuit Diagnosis — 1Roof - Symptom Diagnosis — 1Roof - Removal and Installation — 1Exterior - System Description — 1Exterior - Removal and Installation — 1Body Repair - Repair Information — 1Exterior Lighting System - Led Headlamp — 1Interior Lighting System - Dtc/circuit Diagnosis — 1Interior Lighting System - Removal and Installation — 1Wiper & Washer - System Description — 1Wiper & Washer - Dtc/circuit Diagnosis — 1Wiper & Washer - Symptom Diagnosis — 1Wiper & Washer - Removal and Installation — 1Defogger - System Description — 1Defogger - Dtc/circuit Diagnosis — 1Defogger - Symptom Diagnosis — 1Defogger - Removal and Installation — 1Horn - Removal and Installation — 1Body Control System - Basic Inspection — 1Body Control System - Dtc/circuit Diagnosis — 1Body Control System - Symptom Diagnosis — 1Body Control System - Removal and Installation — 1Lan System - Can Fundamental — 1Lan System - Can — 1Lan System - Can Gateway — 1Power Control System - Ipdm E/r — 1Power Control System - Power Distribution System — 1Charging System - System Description — 1Charging System - Dtc/circuit Diagnosis — 1Power Supply, Ground & Circuit Elements - System Description — 1Power Supply, Ground & Circuit Elements - Basic Inspection — 1Power Supply, Ground & Circuit Elements - Removal and Installation — 1Warning Chime System - System Description — 1Warning Chime System - Dtc/circuit Diagnosis — 1Warning Chime System - Symptom Diagnosis — 1Sonar System - System Description — 1Sonar System - Basic Inspection — 1Sonar System - Dtc/circuit Diagnosis — 1Sonar System - Symptom Diagnosis — 1Sonar System - Removal and Installation — 1Audio, Visual & Navigation System - Nissanconnect — 1Audio, Visual & Navigation System - Intelligent Around View Monitor System — 1Audio, Visual & Navigation System - Rear View Monitor System — 1Audio, Visual & Navigation System - Telematics System — 1Driver Assistance System - Adas Control Unit 2 — 1Driver Assistance System - Driver Assistance System — 1Driver Assistance System - Chassis Control — 1Drive Mode System - Removal and Installation — 1Dtc/circuit Diagnosis (C053c Wheel Speed Sensor ... U2141 Can Comm Circuit) — 1Dtc/circuit Diagnosis (P0011 Intake Valve Timing Control ... P0111 Iat Sensor) — 1Dtc/circuit Diagnosis (P0116 Engine Coolant Temperature Sensor ... P025b Fuel Pump Module a) — 1Dtc/circuit Diagnosis (P026b Injection Timing ... P0420 Three Way Catalyst Function) — 1Dtc/circuit Diagnosis (P0441 Evap Control System ... P0524 Engine Oil Pressure) — 1Dtc/circuit Diagnosis (P0532 A/c Refrigerant Pressure Sensor ... P064d Ecm) — 1Dtc/circuit Diagnosis (P06da Engine Oil Pressure Control Solenoid Valve ... P1217 Engine Over Temperature) — 1Dtc/circuit Diagnosis (P1220 Fuel Pump Control Module (fpcm) ... P1574 Ascd Vehicle Speed Sensor) — 1Dtc/circuit Diagnosis (P1575 Brake Switch ... P2101 Electric Throttle Control Function) — 1Dtc/circuit Diagnosis (P2118 Throttle Control Motor ... P34ac Electric Intake Valve Timing Control Actuator) — 1Dtc/circuit Diagnosis (Active Grille Shutter ... High Pressure Fuel Pump) — 1Dtc/circuit Diagnosis (Ignition Signal ... Variable Induction Air System) — 14012 C1040 Emergency Brake — 14013 C106a Wheel Sensor — 14014 C1078-55 Not Configuration — 14015 C10b4-98 Overheat — 14016 B1001 Lap Pre-Tensioner Lh — 14017 B0001 Driver Air Bag Module — 14018 B100e Knee Air Bag Module Rh — 14019 B142x Collision Detection — 1Dtc/circuit Diagnosis (B20c7-11 A/c Clutch ... B24a6-11 in-Vehicle Sensor) — 1Dtc/circuit Diagnosis (B24a6-15 in-Vehicle Sensor ... U2140-87 Can Comm Err (ecm)) — 1Dtc/circuit Diagnosis (C1f00-1c Control Unit ... C1f04-61 Brake Sw/stop Lamp Sw) — 1Dtc/circuit Diagnosis (C1f05-49 Front Camera Unit ... C1f70-87 Ethernet Circuit) — 1
162steps
~972min
5/5difficulty
Done 0 of 162
  • B0001 Driver Air Bag Module
  • B0010 Assist A/b Module
  • B0030 Rear Side A/b Module Lh
  • B0052 Front Seat Belt Buckle Switch Rh
  • B0073 Pre-Ten Rear Lh
  • B0094 Crash Zone Sens
  • B00a0 Occupant Sens Unit
  • B00d5 Pass A/b Indicator
  • B1000 Air Bag Diagnosis Sensor Unit
  • B1004 Passenger Air Bag Module Active Vent

B0001 Driver Air Bag Module Nissan Pathfinder

DTC Description

DESCRIPTION

DTC B0001 DRIVER AIR BAG MODULE

The driver air bag module is dual stage and wired to the air bag diagnosis sensor unit through the spiral cable. The air bag diagnosis sensor unit will monitor for opens and shorts in detected lines to the driver air bag module including the spiral cable.

PART LOCATION

Refer to Component Parts Location.

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC detecting condition
B0001

DRIVER AIR BAG MODULE

[SHORT]
1A Diagnosis condition When push-button ignition switch is ON.
Signal (terminal) Driver air bag module circuit (DR1) (terminals 37 and 38)
Threshold —
Diagnosis delay time —

DRIVER AIR BAG MODULE

[OPEN]
13 Diagnosis condition When push-button ignition switch is ON.
Signal (terminal) Driver air bag module circuit (DR1) (terminals 37 and 38)
Threshold —
Diagnosis delay time —

DRIVER AIR BAG MODULE

[VB-SHORT]
12 Diagnosis condition When push-button ignition switch is ON.
Signal (terminal) Driver air bag module circuit (DR1) (terminals 37 and 38)
Threshold —
Diagnosis delay time —

DRIVER AIR BAG MODULE

[GND-SHORT]
11 Diagnosis condition When push-button ignition switch is ON.
Signal (terminal) Driver air bag module circuit (DR1) (terminals 37 and 38)
Threshold —
Diagnosis delay time —

DRIVER AIR BAG MODULE

[SHORT]
09 Diagnosis condition When push-button ignition switch is ON.
Signal (terminal) Driver air bag module circuit (DR1) (terminals 37 and 38)
Threshold —
Diagnosis delay time —

DRIVER AIR BAG MODULE

[SHORT]
00 Diagnosis condition When push-button ignition switch is ON.
Signal (terminal) Driver air bag module circuit (DR1) (terminals 37 and 38)
Threshold —
Diagnosis delay time —

POSSIBLE CAUSE

[OPEN]

  • Connection malfunction or open circuit of harness and connector

  • Internal malfunction of driver air bag module

  • Internal malfunction of air bag diagnosis sensor unit

[VB-SHORT]

  • Connection malfunction or short circuit to power supply of harness and connector

  • Internal malfunction of driver air bag module

  • Internal malfunction of air bag diagnosis sensor unit

[GND-SHORT]

  • Connection malfunction or short circuit to ground of harness and connector

  • Internal malfunction of driver air bag module

  • Internal malfunction of air bag diagnosis sensor unit

[SHORT]

  • Connection malfunction or short circuit of harness and connector

  • Internal malfunction of driver air bag module

  • Internal malfunction of air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE (With CONSULT)

CHECK SELF-DIAG RESULT

CONSULT

  1. Ignition ON.

  2. Check for DTC.

Is the DTC detected?

YES>>

Refer to Diagnosis Procedure.

YES>>

GO TO 2.

NO>>

Inspection End.

ERASE SELF-DIAG RESULT

CONSULT

Erase the DTC.

Can the DTC be erased?

YES>>

Inspection End.

NO>>

Refer to Diagnosis Procedure.

DTC CONFIRMATION PROCEDURE (Without CONSULT)

CHECK SELF-DIAG RESULT

  1. Ignition switch ON.

  2. Check the air bag warning lamp status. Refer to Trouble Diagnosis without CONSULT.

Is the DTC detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

Inspection End.

Diagnosis Procedure

HARNESS CONNECTOR

Visually inspect all applicable harness connectors for the following:

  • Visible damage to connector or terminal

  • Loose terminal

  • Poor connection

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Perform one of the following repairs:

  • Visible damage: Replace the harness.

  • Loose terminal: Secure the terminal.

  • Poor connection: Secure the connection.

CONFIRM DTC

CONSULT

  1. Reconnect all harness connectors.

  2. Ignition switch ON.

  3. Check for DTC.

Is DTC still current?

YES>>

GO TO 3.

NO>>

Refer to Intermittent Incident.

WIRING HARNESS

Check the wiring harness for visible damage.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Replace the harness.

CHECK SPIRAL CABLE CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect driver air bag module harness connectors and spiral cable harness connector.

  3. Check continuity between driver air bag module harness connector and spiral cable connector.

    Driver air bag moduleSpiral cableContinuity
    ConnectorTerminalConnectorTerminal
    M89 39 M53 18 Yes
    40 19
    M87 37 20
    38 19
  4. Check continuity between driver air bag module harness connector and ground.

    Driver air bag module Ground Continuity
    Connector Terminal
    M89 39 No
    40
    M87 37
    38

Is DTC still current?

YES>>

GO TO 5.

NO>>

Refer to Intermittent Incident.

DRIVER AIR BAG MODULE

CONSULT

  1. Replace the driver air bag module. Refer to Removal and Installation.

  2. Ignition switch ON.

  3. Check for DTC.

Is DTC still current?

YES>>

GO TO 6.

NO>>

Clear DTC. Inspection End.

AIR BAG DIAGNOSIS SENSOR UNIT

CONSULT

  1. Replace the air bag diagnosis sensor unit. Refer to Removal and Installation.

  2. Ignition switch ON.

  3. Check for DTC.

Is DTC still current?

YES>>

GO TO 7.

NO>>

Clear DTC. Inspection End.

RELATED HARNESS

Replace the related harness.

>>

Inspection End.

B0010 Assist A/b Module Nissan Pathfinder Fifth generation

DTC Description

DESCRIPTION

DTC B0010 PASSENGER AIR BAG MODULE

The passenger air bag module is dual stage (US/CAN models) and single stage (MEX models) and is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit will monitor for opens and shorts in detected lines to the passenger air bag module.

PART LOCATION

Refer to Component Parts Location.

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC detecting condition
B0010

ASSIST A/B MODULE

[SHORT]
1A Diagnosis condition When push-button ignition switch is ON
Signal (terminal) Front passenger air bag module circuit (AS1) (terminals 1 and 2)
Threshold —
Diagnosis delay time —

ASSIST A/B MODULE

[OPEN]
13 Diagnosis condition When push-button ignition switch is ON
Signal (terminal) Front passenger air bag module circuit (AS1) (terminals 1 and 2)
Threshold —
Diagnosis delay time —

ASSIST A/B MODULE

[VB-SHORT]
12 Diagnosis condition When push-button ignition switch is ON
Signal (terminal) Front passenger air bag module circuit (AS1) (terminals 1 and 2)
Threshold —
Diagnosis delay time —

ASSIST A/B MODULE

[GND-SHORT]
11 Diagnosis condition When push-button ignition switch is ON
Signal (terminal) Front passenger air bag module circuit (AS1) (terminals 1 and 2)
Threshold —
Diagnosis delay time —

ASSIST A/B MODULE

[SHORT]
09 Diagnosis condition When push-button ignition switch is ON
Signal (terminal) Front passenger air bag module circuit (AS1) (terminals 1 and 2)
Threshold —
Diagnosis delay time —

POSSIBLE CAUSE

[OPEN]

  • Connection malfunction or open circuit of harness and connector

  • Internal malfunction of front passenger air bag module

  • Internal malfunction of air bag diagnosis sensor unit

[VB-SHORT]

  • Connection malfunction or short circuit to power supply of harness and connector

  • Internal malfunction of front passenger air bag module

  • Internal malfunction of air bag diagnosis sensor unit

[GND-SHORT]

  • Connection malfunction or short circuit to ground of harness and connector

  • Internal malfunction of front passenger air bag module

  • Internal malfunction of air bag diagnosis sensor unit

[SHORT]

  • Connection malfunction or short circuit of harness and connector

  • Internal malfunction of front passenger air bag module

  • Internal malfunction of air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE (With CONSULT)

CHECK SELF-DIAG RESULT

CONSULT

  1. Ignition switch ON.

  2. Check for DTC.

Is the DTC detected?

YES>>

Refer to Diagnosis Procedure.

YES>>

GO TO 2.

NO>>

Inspection End.

ERASE SELF-DIAG RESULT

CONSULT

Erase the DTC.

Can the DTC be erased?

YES>>

Inspection End.

NO>>

Refer to Diagnosis Procedure.

DTC CONFIRMATION PROCEDURE (Without CONSULT)

CHECK SELF-DIAG RESULT

  1. Ignition switch ON.

  2. Check the air bag warning lamp status. Refer to Trouble Diagnosis without CONSULT.

Is the DTC detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

Inspection End.

Diagnosis Procedure

HARNESS CONNECTOR

Visually inspect all applicable harness connectors for the following:

  • Visible damage to connector or terminal

  • Loose terminal

  • Poor connection

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Perform one of the following repairs:

  • Visible damage: Replace the harness.

  • Loose terminal: Secure the terminal.

  • Poor connection: Secure the connection.

CONFIRM DTC

CONSULT

  1. Reconnect all harness connectors.

  2. Ignition switch ON.

  3. Check for DTC.

Is DTC still current?

YES>>

GO TO 3.

NO>>

Refer to Intermittent Incident.

WIRING HARNESS

Check the wiring harness for visible damage.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Replace the harness.

CONFIRM DTC

CONSULT

  1. Reconnect all harness connectors.

  2. Ignition switch ON.

  3. Check for DTC.

Is DTC still current?

YES>>

GO TO 5.

NO>>

Refer to Intermittent Incident.

FRONT PASSENGER AIR BAG MODULE

CONSULT

  1. Replace the front passenger air bag module. Refer to Removal and Installation.

  2. Ignition switch ON.

  3. Check for DTC.

Is DTC still current?

YES>>

GO TO 6.

NO>>

Clear DTC. Inspection End.

AIR BAG DIAGNOSIS SENSOR UNIT

CONSULT

  1. Replace the air bag diagnosis sensor unit. Refer to Removal and Installation.

  2. Ignition switch ON.

  3. Check for DTC.

Is DTC still current?

YES>>

GO TO 7.

NO>>

Clear DTC. Inspection End.

RELATED HARNESS

Replace the related harness.

>>

Inspection End.

B0030 Rear Side A/b Module Lh Nissan Pathfinder 2026

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC Detection Condition
B0030-1A

REAR SIDE A/B MODULE LH

(Second Row Left Side Air bag Deployment Control)
Diagnosis condition When ignition switch is ON.
Signal (terminal) Rear side air bag module LH signal
Threshold Rear side air bag module LH circuits are shorted to each other
Diagnosis delay time 2 seconds or more.
B0030-1B

REAR SIDE A/B MODULE LH

(Second Row Left Side Air bag Deployment Control)
Diagnosis condition When ignition switch is ON.
Signal (terminal) Rear side air bag module LH signal
Threshold Rear side air bag module LH circuit resistance is above threshold
Diagnosis delay time 2 seconds or more.
B0030-55

REAR SIDE A/B MODULE LH

(Second Row Left Side Air bag Deployment Control)
Diagnosis condition When ignition switch is ON.
Signal (terminal) Rear side air bag module LH signal
Threshold When a mismatch is detected between in the configuration data stored in the air bag diagnosis sensor unit and Nissan Pathfinder vehicle specification.
Diagnosis delay time 2 seconds or more.
B0030-11

REAR SIDE A/B MODULE LH

(Second Row Left Side Air bag Deployment Control)
Diagnosis condition When ignition switch is ON.
Signal (terminal) Rear side air bag module LH signal
Threshold Rear side air bag module LH circuit is shorted to ground
Diagnosis delay time 2 seconds or more.
B0030-09

REAR SIDE A/B MODULE LH

(Second Row Left Side Air bag Deployment Control)
Diagnosis condition When ignition switch is ON.
Signal (terminal) Rear side air bag module LH signal
Threshold Rear side air bag module LH circuit is shorted to other
Diagnosis delay time 2 seconds or more.
B0030-12

REAR SIDE A/B MODULE LH

(Second Row Left Side Air bag Deployment Control)
Diagnosis condition When ignition switch is ON.
Signal (terminal) Rear side air bag module LH signal
Threshold Rear side air bag module LH circuit is shorted to power supply circuit
Diagnosis delay time 2 seconds or more.
B0030-13

REAR SIDE A/B MODULE LH

(Second Row Left Side Air bag Deployment Control)
Diagnosis condition When ignition switch is ON.
Signal (terminal) Rear side air bag module LH signal
Threshold Rear side air bag module LH circuit is open
Diagnosis delay time 2 seconds or more.

POSSIBLE CAUSE

  • Connection malfunction of harness and connector

  • Internal malfunction of rear side air bag module LH

  • Internal malfunction of air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

CONSULT

  1. Ignition switch ON.

  2. Select “Self Diagnostic Result” mode of “AIR BAG”.

Is malfunctioning part detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Replace wiring harness.

REPLACE REAR SIDE AIR BAG MODULE LH

  1. Replace rear side air bag module LH. Refer to Removal and Installation.

  2. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

GO TO 4.

NO>>

Inspection End.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

  1. Replace air bag diagnosis sensor unit. Refer to Removal and Installation.

  2. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

GO TO 1.

NO>>

Inspection End.

B0052 Front Seat Belt Buckle Switch Rh Nissan Pathfinder R53

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC Detection Condition
B0052–11

Front seat belt buckle switch RH

(Passenger Seat Belt Sensor)
Diagnosis condition When ignition switch is ON.
Signal (terminal) Front seat belt buckle switch RH signal
Threshold Front seat belt buckle switch RH circuit is shorted to ground
Diagnosis delay time 2 seconds or more.
B0052–12

Front seat belt buckle switch RH

(Passenger Seat Belt Sensor)
Diagnosis condition When ignition switch is ON.
Signal (terminal) Front seat belt buckle switch RH signal
Threshold Front seat belt buckle switch RH circuit is shorted to power supply circuit
Diagnosis delay time 2 seconds or more.
B0052–2B

Front seat belt buckle switch RH

(Passenger Seat Belt Sensor)
Diagnosis condition When ignition switch is ON.
Signal (terminal) Front seat belt buckle switch RH signal
Threshold Front seat belt buckle switch RH circuit is shorted to other
Diagnosis delay time 2 seconds or more.
B0052–29

Front seat belt buckle switch RH

(Passenger Seat Belt Sensor)
Diagnosis condition When ignition switch is ON.
Signal (terminal) Front seat belt buckle switch RH signal
Threshold Front seat belt buckle switch RH circuit is out of order
Diagnosis delay time 2 seconds or more.

POSSIBLE CAUSE

  • Connection malfunction or open circuit of harness and connector

  • Internal malfunction of front seat belt buckle switch RH

  • Internal malfunction of air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAGNOSTIC RESULT

CONSULT

  1. Ignition switch ON.

  2. Select “Self Diagnostic Result” mode of “AIR BAG”.

Is malfunctioning part detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Replace wiring harness.

REPLACE FRONT SEAT BELT BUCKLE SWITCH RH

  1. Replace front seat belt buckle RH. Refer to Removal and Installation.

  2. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

GO TO 4.

NO>>

Inspection End.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

  1. Replace air bag diagnosis sensor unit. Refer to Removal and Installation.

  2. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

GO TO 1.

NO>>

Inspection End.

B0073 Pre-Ten Rear Lh Nissan Pathfinder R53

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC Detection Condition
B0073-09

PRE-TEN REAR LH

(Second Row Left Seat Belt Pretensioner Deployment Control)
Diagnosis condition When ignition switch is ON.
Signal (terminal) Rear seat belt pre-tensioner LH signal
Threshold Rear seat belt pre-tensioner LH circuit is shorted to other
Diagnosis delay time 2 seconds or more.
B0073-1A

PRE-TEN REAR LH

(Second Row Left Seat Belt Pretensioner Deployment Control)
Diagnosis condition When ignition switch is ON.
Signal (terminal) Rear seat belt pre-tensioner LH signal
Threshold Rear seat belt pre-tensioner LH circuits are shorted to each other
Diagnosis delay time 2 seconds or more.
B0073-1B

PRE-TEN REAR LH

(Second Row Left Seat Belt Pretensioner Deployment Control)
Diagnosis condition When ignition switch is ON.
Signal (terminal) Rear seat belt pre-tensioner LH signal
Threshold Rear seat belt pre-tensioner LH circuit resistance is above threshold
Diagnosis delay time 2 seconds or more.
B0073-11

PRE-TEN REAR LH

(Second Row Left Seat Belt Pretensioner Deployment Control)
Diagnosis condition When ignition switch is ON.
Signal (terminal) Rear seat belt pre-tensioner LH signal
Threshold Rear seat belt pre-tensioner LH circuit is shorted to ground
Diagnosis delay time 2 seconds or more.
B0073-13

PRE-TEN REAR LH

(Second Row Left Seat Belt Pretensioner Deployment Control)
Diagnosis condition When ignition switch is ON.
Signal (terminal) Rear seat belt pre-tensioner LH signal
Threshold Rear seat belt pre-tensioner LH circuit is shorted to other
Diagnosis delay time 2 seconds or more.

POSSIBLE CAUSE

  • Connection malfunction or short circuit of harness and connector

  • Internal malfunction of rear seat belt pre-tensioner LH

  • Internal malfunction of air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

CONSULT

  1. Ignition switch ON.

  2. Perform “Self Diagnostic Result” mode of “AIR BAG”.

Is malfunctioning part detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End

Diagnosis Procedure

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Replace wiring harness.

REPLACE REAR SEAT BELT PRE-TENSIONER LH

  1. Replace rear seat belt pre-tensioner LH. Refer to Removal and Installation.

  2. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

GO TO 4.

NO>>

Inspection End.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

  1. Replace air bag diagnosis sensor unit. Refer to Removal and Installation.

  2. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

GO TO 1.

NO>>

Inspection End.

B0094 Crash Zone Sens Nissan Pathfinder SUV

DTC Description

DESCRIPTION

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC detecting condition
B0094

CRASH ZONE SENS

[RESET]
93 Diagnosis condition When ignition switch is ON.
Signal (terminal) Crash zone sensor (terminals 55 and 56)
Threshold —
Diagnosis delay time —

CRASH ZONE SENS

[COMM ERR]
81 Diagnosis condition When ignition switch is ON.
Signal (terminal) Crash zone sensor (terminals 55 and 56)
Threshold —
Diagnosis delay time —

CRASH ZONE SENS

[OPEN]
88 Diagnosis condition When ignition switch is ON.
Signal (terminal) Crash zone sensor (terminals 55 and 56)
Threshold —
Diagnosis delay time —

CRASH ZONE SENS

[UNMATCH]
86 Diagnosis condition When ignition switch is ON.
Signal (terminal) Crash zone sensor (terminals 55 and 56)
Threshold —
Diagnosis delay time —

CRASH ZONE SENS

[OFFSET ERR]
28 Diagnosis condition When ignition switch is ON.
Signal (terminal) Crash zone sensor (terminals 55 and 56)
Threshold —
Diagnosis delay time —

CRASH ZONE SENS

[SELF-DIAG ERR]
25 Diagnosis condition When ignition switch is ON.
Signal (terminal) Crash zone sensor (terminals 18 and 19)
Threshold —
Diagnosis delay time —

CRASH ZONE SENS

[LOWER LIMIT ERR]
23 Diagnosis condition When ignition switch is ON.
Signal (terminal) Crash zone sensor (terminals 55 and 56)
Threshold —
Diagnosis delay time —

CRASH ZONE SENS

[UPPER LIMIT ERR]
24 Diagnosis condition When ignition switch is ON.
Signal (terminal) Crash zone sensor (terminals 55 and 56)
Threshold —
Diagnosis delay time —

CRASH ZONE SENS

[GND-SHORT]
11 Diagnosis condition When ignition switch is ON.
Signal (terminal) Crash zone sensor (terminals 55 and 56)
Threshold —
Diagnosis delay time —

POSSIBLE CAUSE

[RESET], [COMM ERR]

  • Connection malfunction of harness or connector

  • Internal malfunction of crash zone sensor

  • Internal malfunction of air bag diagnosis sensor unit

[OPEN]

  • Connection malfunction or open circuit of harness or connector

  • Internal malfunction of crash zone sensor

  • Internal malfunction of air bag diagnosis sensor unit

[UNMATCH]

  • Air bag diagnosis sensor unit and crash zone sensor is different from the part specified

[OFFSET ERR], [SELF-DIAG ERR], [LOWER LIMIT ERR], [UPPER LIMIT ERR]

  • Internal malfunction of crash zone sensor

  • Internal malfunction of air bag diagnosis sensor unit

[GND-SHORT]

  • Connection malfunction or short circuit to ground of harness or connector

  • Internal malfunction of crash zone sensor

  • Internal malfunction of air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE (With CONSULT)

CHECK SELF-DIAG RESULT

CONSULT

  1. Ignition switch ON.

  2. Check for DTC.

Is the DTC detected?

YES>>

Refer to Diagnosis Procedure.

YES>>

GO TO 2.

NO>>

Inspection End.

ERASE SELF-DIAG RESULT

CONSULT

Erase the DTC.

Can the DTC be erased?

YES>>

Inspection End.

NO>>

Refer to Diagnosis Procedure.

DTC CONFIRMATION PROCEDURE (Without CONSULT)

CHECK SELF-DIAG RESULT

CONSULT

  1. Ignition switch ON.

  2. Check the air bag warning lamp status. Refer to Trouble Diagnosis without CONSULT.

Is the DTC detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

Inspection End.

Diagnosis Procedure

HARNESS CONNECTOR

Visually inspect all applicable harness connectors for the following:

  • Visible damage to connector or terminal

  • Loose terminal

  • Poor connection

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Perform one of the following repairs:

  • Visible damage: Replace the harness.

  • Loose terminal: Secure the terminal.

  • Poor connection: Secure the connection.

CONFIRM DTC

CONSULT

  1. Reconnect all harness connectors.

  2. Ignition switch ON.

  3. Check for DTC.

Is DTC still current?

YES>>

GO TO 3.

NO>>

Refer to Intermittent Incident.

WIRING HARNESS

Check the wiring harness for visible damage.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Replace the harness.

CONFIRM DTC

CONSULT

  1. Reconnect all harness connectors.

  2. Ignition switch ON.

  3. Check for DTC.

Is DTC still current?

YES>>

GO TO 5.

NO>>

Refer to Intermittent Incident.

CRASH ZONE SENSOR

CONSULT

  1. Replace the crash zone sensor. Refer to Removal and Installation.

  2. Ignition switch ON.

  3. Check for DTC.

Is DTC still current?

YES>>

GO TO 6.

NO>>

Clear DTC. Inspection End.

AIR BAG DIAGNOSIS SENSOR UNIT

CONSULT

  1. Replace the air bag diagnosis sensor unit. Refer to Removal and Installation.

  2. Ignition switch ON.

  3. Check for DTC.

Is DTC still current?

YES>>

GO TO 7.

NO>>

Clear DTC. Inspection End.

RELATED HARNESS

Replace the related harness.

>>

Inspection End.

B00a0 Occupant Sens Unit Nissan Pathfinder 2026

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC detecting condition
B00A0

OCCUPANT SENS UNIT

[Occupant Classification System (Subfault)]
[ABNORMAL VOLTAGE] 00 Diagnosis condition Ignition switch ON.
Signal (terminal) Occupant detection sensor signal
Threshold Power supply malfunction of occupant detection sensor
Diagnosis delay time —
[UNIT MALFUNC] 02 Diagnosis condition Ignition switch ON.
Signal (terminal) Occupant detection sensor signal
Threshold Malfunction of occupant detection sensor
Diagnosis delay time —
[UNIT MALFUNC] 09 Diagnosis condition Ignition switch ON.
Signal (terminal) Occupant detection sensor signal
Threshold Malfunction of occupant detection sensor
Diagnosis delay time —

OCCUPANT SENS UNIT

[Occupant Classification System (Subfault)]
[UNIT MALFUNC] 04 Diagnosis condition Ignition switch ON.
Signal (terminal) Occupant detection sensor unit signal
Threshold Malfunction of occupant detection sensor control unit
Diagnosis delay time —
[COMM ERR] 83 Diagnosis condition Ignition switch ON.
Signal (terminal) Occupant detection sensor unit signal
Threshold
  • Communication malfunction of occupant detection sensor control unit

  • Communication blank of occupant detection sensor control unit

Diagnosis delay time —
[COMM ERR] 86 Diagnosis condition Ignition switch ON.
Signal (terminal) Occupant detection sensor unit signal
Threshold
  • Communication malfunction of occupant detection sensor control unit

  • Communication blank of occupant detection sensor control unit

Diagnosis delay time —
B00A0 [COMM ERR] 87 Diagnosis condition Ignition switch ON.
Signal (terminal) Occupant detection sensor unit signal
Threshold
  • Communication malfunction of occupant detection sensor control unit

  • Communication blank of occupant detection sensor control unit

Diagnosis delay time —
[COMM ERR] 88 Diagnosis condition Ignition switch ON.
Signal (terminal) Occupant detection sensor unit signal
Threshold
  • Communication malfunction of occupant detection sensor control unit

  • Communication blank of occupant detection sensor control unit

Diagnosis delay time —
[UNDEFINED] 8F Diagnosis condition Ignition switch ON.
Signal (terminal) Occupant detection sensor unit signal
Threshold Undefined status of occupant detection sensor control unit
Diagnosis delay time —
[RESET] 93 Diagnosis condition Ignition switch ON.
Signal (terminal) Occupant detection sensor unit signal
Threshold Reset malfunction of occupant detection sensor control unit
Diagnosis delay time —

POSSIBLE CAUSE

  • [B00A0–00]

    • Connection malfunction or short circuit to power supply of harness or connector

    • Internal malfunction of occupant detection sensor

    • Internal malfunction of air bag diagnosis sensor unit

  • [B00A0–02, B00A0–09]

    • Connection malfunction of harness and connector

    • Internal malfunction of occupant detection sensor

    • Internal malfunction of air bag diagnosis sensor unit

  • [B00A0–04, B00A0–83, B00A0–86, B00A0–87, B00A0–88, B00A0–8F]

    • Connection malfunction or open circuit of harness and connector

    • Internal malfunction of occupant detection sensor control unit

    • Internal malfunction of air bag diagnosis sensor unit

  • [B00A0–93]

    • Connection malfunction of harness and connector

    • Internal malfunction of occupant detection sensor control unit

    • Internal malfunction of air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE (With CONSULT)

CHECK SELF-DIAG RESULT

CONSULT

  1. Ignition switch ON.

  2. Check the DTC.

Is the DTC detected?

YES>>

Refer to:

  • B00A0-00, -02 or -09: Diagnosis Procedure (B00A0-00, -02 or -09)

  • B00A0-04: Diagnosis Procedure (B00A0-04)

  • B00A0-83, -86, -87, -88 or -8F: Diagnosis Procedure (B00A0-83, -86, -87, -88 or -8F)

  • B00A0-93: Diagnosis Procedure (B00A0-93)

YES>>

GO TO 2.

NO>>

Inspection End.

ERASE SELF-DIAG RESULT

CONSULT

Erase the DTC.

Can the DTC be erased?

YES>>

Inspection End.

NO>>

Refer to:

  • B00A0-00, -02 or -09: Diagnosis Procedure (B00A0-00, -02 or -09)

  • B00A0-04: Diagnosis Procedure (B00A0-04)

  • B00A0-83, -86, -87, -88 or -8F: Diagnosis Procedure (B00A0-83, -86, -87, -88 or -8F)

  • B00A0-93: Diagnosis Procedure (B00A0-93)

DTC CONFIRMATION PROCEDURE (Without CONSULT)

CHECK SELF-DIAG RESULT

  1. Ignition switch ON.

  2. Check the air bag warning lamp status. Refer to SRS Operation Check.

Is the DTC detected?

YES>>

Refer to:

  • B00A0-00, -02 or -09: Diagnosis Procedure (B00A0-00, -02 or -09)

  • B00A0-04: Diagnosis Procedure (B00A0-04)

  • B00A0-83, -86, -87, -88 or -8F: Diagnosis Procedure (B00A0-83, -86, -87, -88 or -8F)

  • B00A0-93: Diagnosis Procedure (B00A0-93)

NO>>

Inspection End.

Diagnosis Procedure (B00A0-00, -02 or -09)

HARNESS CONNECTOR

Visually inspect all applicable harness connectors for the following:

  • Visible damage to connector or terminal

  • Loose terminal

  • Poor connection

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Perform the following repairs. Then, GO TO 2.

  • Visible damage: Replace the harness.

  • Loose terminal: Secure the terminal.

  • Poor connection: Secure the connection.

CONFIRM DTC

CONSULT

  1. Reconnect all harness connectors.

  2. Ignition switch ON.

  3. Check for DTC.

Is DTC still current?

YES>>

GO TO 3.

NO>>

Clear DTC and perform zero point reset. Refer to Description.

REPLACE OCS CONTROL UNIT AND SENSORS

CONSULT

  1. Replace the OCS control unit and sensors. Refer to Removal and Installation.

  2. Ignition switch ON.

  3. Check for DTC.

Is DTC still current?

YES>>

GO TO 4.

NO>>

Clear DTC and perform zero point reset. Refer to Description.

AIR BAG DIAGNOSIS SENSOR UNIT

CONSULT

  1. Replace the air bag diagnosis sensor unit. Refer to Removal and Installation.

  2. Ignition switch ON.

  3. Check for DTC.

Is DTC still current?

YES>>

GO TO 5.

NO>>

Clear DTC and perform zero point reset. Refer to Description.

RELATED HARNESS

CONSULT

  1. Replace the related harnesses (OCS sensors to OCS control unit, OCS control unit to seat, seat to main harness, main harness to air bag diagnosis sensor unit).

  2. Ignition switch ON.

  3. Check for DTC.

Is DTC still current?

YES>>

GO TO 6.

NO>>

Clear DTC and perform zero point reset. Refer to Description.

REPLACE PASSENGER SEAT CUSHION FRAME

CONSULT

  1. Replace the passenger seat cushion frame. Refer to Seat Cushion.

  2. Clear DTC and perform zero point reset. Refer to Description.

>>

Inspection End.

Diagnosis Procedure (B00A0-04)

HARNESS CONNECTOR

Visually inspect all applicable harness connectors for the following:

  • Visible damage to connector or terminal

  • Loose terminal

  • Poor connection

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Perform the following repairs. Then, GO TO 2.

  • Visible damage: Replace the harness.

  • Loose terminal: Secure the terminal.

  • Poor connection: Secure the connection.

CONFIRM DTC

CONSULT

  1. Reconnect all harness connectors.

  2. Ignition switch ON.

  3. Check for DTC.

Is DTC still current?

YES>>

GO TO 3.

NO>>

Clear DTC and perform zero point reset. Refer to Description.

REPLACE OCS CONTROL UNIT

CONSULT

  1. Replace the OCS control unit. Refer to Removal and Installation.

  2. Ignition switch ON.

  3. Check for DTC.

Is DTC still current?

YES>>

GO TO 4.

NO>>

Clear DTC and perform zero point reset. Refer to Description.

AIR BAG DIAGNOSIS SENSOR UNIT

CONSULT

  1. Replace the air bag diagnosis sensor unit. Refer to Removal and Installation.

  2. Ignition switch ON.

  3. Check for DTC.

Is DTC still current?

YES>>

GO TO 5.

NO>>

Clear DTC and perform zero point reset. Refer to Description.

RELATED HARNESS

CONSULT

  1. Replace the related harnesses (OCS sensors to OCS control unit, OCS control unit to seat, seat to main harness, main harness to air bag diagnosis sensor unit)

  2. Ignition switch ON.

  3. Check for DTC.

Is DTC still current?

YES>>

GO TO 6.

NO>>

Clear DTC and perform zero point reset. Refer to Description.

REPLACE OCS SENSORS

CONSULT

  1. Replace the OCS sensors. Refer to Removal and Installation.

  2. Ignition switch ON.

  3. Check for DTC.

Is DTC still current?

YES>>

GO TO 7.

NO>>

Clear DTC and perform zero point reset. Refer to Description.

REPLACE PASSENGER SEAT CUSHION FRAME

CONSULT

  1. Replace the passenger seat cushion frame. Refer to Seat Cushion.

  2. Clear DTC and perform zero point reset. Refer to Description.

>>

Inspection End.

Diagnosis Procedure (B00A0-83, -86, -87, -88 or -8F)

HARNESS CONNECTOR

Visually inspect all applicable harness connectors for the following:

  • Visible damage to connector or terminal

  • Loose terminal

  • Poor connection

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Perform the following repairs. Then, GO TO 2.

  • Visible damage: Replace the harness.

  • Loose terminal: Secure the terminal.

  • Poor connection: Secure the connection.

CONFIRM DTC

CONSULT

  1. Reconnect all harness connectors.

  2. Ignition switch ON.

  3. Check for DTC.

Is DTC still current?

YES>>

GO TO 3.

NO>>

Clear DTC and perform zero point reset. Refer to Description.

REPLACE OCS CONTROL UNIT AND SENSORS

CONSULT

  1. Replace the OCS control unit and sensors. Refer to Removal and Installation.

  2. Ignition switch ON.

  3. Check for DTC.

Is DTC still current?

YES>>

GO TO 4.

NO>>

Clear DTC and perform zero point reset. Refer to Description.

AIR BAG DIAGNOSIS SENSOR UNIT

CONSULT

  1. Replace the air bag diagnosis sensor unit. Refer to Removal and Installation.

  2. Ignition switch ON.

  3. Check for DTC.

Is DTC still current?

YES>>

GO TO 5.

NO>>

Clear DTC and perform zero point reset. Refer to Description.

RELATED HARNESS

CONSULT

  1. Replace the related harnesses (OCS sensors to OCS control unit, OCS control unit to seat, seat to main harness, main harness to air bag diagnosis sensor unit).

  2. Ignition switch ON.

  3. Check for DTC.

Is DTC still current?

YES>>

GO TO 6.

NO>>

Clear DTC and perform zero point reset. Refer to Description.

REPLACE PASSENGER SEAT CUSHION FRAME

CONSULT

  1. Replace the passenger seat cushion frame. Refer to Seat Cushion.

  2. Clear DTC and perform zero point reset. Refer to Description.

>>

Inspection End.

Diagnosis Procedure (B00A0-93)

PERFORM ZERO POINT RESET

CONSULT

  1. Perform zero point reset. Refer to Description.

  2. Ignition switch ON.

  3. Check for DTC.

Is DTC still current?

YES>>

GO TO 2.

NO>>

Clear DTC. Inspection End.

HARNESS CONNECTOR

Visually inspect all applicable harness connectors for the following:

  • Visible damage to connector or terminal

  • Loose terminal

  • Poor connection

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Perform the following repairs. Then, GO TO 3.

  • Visible damage: Replace the harness.

  • Loose terminal: Secure the terminal.

  • Poor connection: Secure the connection.

CONFIRM DTC

CONSULT

  1. Reconnect all harness connectors.

  2. Ignition switch ON.

  3. Check for DTC.

Is DTC still current?

YES>>

GO TO 4.

NO>>

Clear DTC and perform zero point reset. Refer to Description.

REPLACE OCS CONTROL UNIT

CONSULT

  1. Replace the OCS control unit. Refer to Removal and Installation.

  2. Ignition switch ON.

  3. Check for DTC.

Is DTC still current?

YES>>

GO TO 5.

NO>>

Clear DTC and perform zero point reset. Refer to Description.

AIR BAG DIAGNOSIS SENSOR UNIT

CONSULT

  1. Replace the air bag diagnosis sensor unit. Refer to Removal and Installation.

  2. Ignition switch ON.

  3. Check for DTC.

Is DTC still current?

YES>>

GO TO 6.

NO>>

Clear DTC and perform zero point reset. Refer to Description.

RELATED HARNESS

CONSULT

  1. Replace the related harnesses (OCS sensors to OCS control unit, OCS control unit to seat, seat to main harness, main harness to air bag diagnosis sensor unit)

  2. Ignition switch ON.

  3. Check for DTC.

Is DTC still current?

YES>>

GO TO 7.

NO>>

Clear DTC and perform zero point reset. Refer to Description.

REPLACE OCS SENSORS

CONSULT

  1. Replace the OCS sensors. Refer to Removal and Installation.

  2. Ignition switch ON.

  3. Check for DTC.

Is DTC still current?

YES>>

GO TO 8.

NO>>

Clear DTC and perform zero point reset. Refer to Description.

REPLACE PASSENGER SEAT CUSHION FRAME

CONSULT

  1. Replace the passenger seat cushion frame. Refer to Seatback.

  2. Clear DTC and perform zero point reset. Refer to Description.

>>

Inspection End.

B00d5 Pass A/b Indicator Nissan Pathfinder Fifth generation

DTC Description

DESCRIPTION

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC detecting condition
B00D5

PASS A/B INDICATOR

[UNIT MALFUNC]
04 Diagnosis condition Ignition switch ON.
Signal (terminal) Front passenger air bag OFF indicator is malfunctioning.
Threshold —
Diagnosis delay time —

PASS A/B INDICATOR

[PWR-SHORT/OPEN]
15 Diagnosis condition Ignition switch ON.
Signal (terminal) Front passenger air bag OFF indicator is malfunctioning.
Threshold —
Diagnosis delay time —

PASS A/B INDICATOR

[OPEN]
13 Diagnosis condition Ignition switch ON.
Signal (terminal) Front passenger air bag OFF indicator is malfunctioning.
Threshold —
Diagnosis delay time —

PASS A/B INDICATOR

[VB-SHORT]
12 Diagnosis condition Ignition switch ON.
Signal (terminal) Front passenger air bag OFF indicator is malfunctioning.
Threshold —
Diagnosis delay time —

PASS A/B INDICATOR

[GND-SHORT]
11 Diagnosis condition Ignition switch ON.
Signal (terminal) Front passenger air bag OFF indicator is malfunctioning.
Threshold —
Diagnosis delay time —

POSSIBLE CAUSE

[UNIT MALFUNC]

  • Internal malfunction of front passenger air bag OFF indicator

  • Internal malfunction of air bag diagnosis sensor unit

[PWE-SHORT/OPEN]

  • Connection malfunction or short circuit to power supply of harness and connector

  • Connection malfunction or open circuit of harness and connector

  • Internal malfunction of front passenger air bag OFF indicator

  • Internal malfunction of air bag diagnosis sensor unit

[OPEN]

  • Connection malfunction or open circuit of harness and connector

  • Internal malfunction of front passenger air bag OFF indicator

  • Internal malfunction of air bag diagnosis sensor unit

[VB-SHORT]

  • Connection malfunction or short circuit to power supply of harness and connector

  • Internal malfunction of front passenger air bag OFF indicator

  • Internal malfunction of air bag diagnosis sensor unit

[GND-SHORT]

  • Connection malfunction or short circuit to ground of harness and connector

  • Internal malfunction of front passenger air bag OFF indicator

  • Internal malfunction of air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE (With CONSULT)

CHECK SELF-DIAG RESULT

CONSULT

  1. Ignition switch ON.

  2. Check for DTC.

Is the DTC detected?

YES>>

Refer to Diagnosis Procedure.

YES>>

GO TO 2.

NO>>

Inspection End.

ERASE SELF-DIAG RESULT

CONSULT

Erase the DTC.

Can the DTC be erased?

YES>>

Inspection End.

NO>>

Refer to Diagnosis Procedure.

DTC CONFIRMATION PROCEDURE (Without CONSULT)

CHECK SELF-DIAG RESULT

  1. Ignition switch ON.

  2. Check the air bag warning lamp status. Refer to Trouble Diagnosis without CONSULT.

Is the DTC detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

Inspection End.

Diagnosis Procedure

HARNESS CONNECTOR

Visually inspect all applicable harness connectors for the following:

  • Visible damage to connector or terminal

  • Loose terminal

  • Poor connection

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Perform one of the following repairs:

  • Visible damage: Replace the harness.

  • Loose terminal: Secure the terminal.

  • Poor connection: Secure the connection.

CONFIRM DTC

CONSULT

  1. Reconnect all harness connectors.

  2. Ignition switch ON.

  3. Check for DTC.

Is DTC still current?

YES>>

GO TO 3.

NO>>

Refer to Intermittent Incident.

WIRING HARNESS

Check the wiring harness for visible damage.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Replace the harness.

CONFIRM DTC

CONSULT

  1. Reconnect all harness connectors.

  2. Ignition switch ON.

  3. Check for DTC.

Is DTC still current?

YES>>

GO TO 5.

NO>>

Refer to Intermittent Incident.

PASSENGER AIR BAG OFF INDICATOR

CONSULT

  1. Replace the passenger air bag off indicator. Refer to Removal and Installation.

  2. Ignition switch ON.

  3. Check for DTC.

Is DTC still current?

YES>>

GO TO 6.

NO>>

Clear DTC. Inspection End.

AIR BAG DIAGNOSIS SENSOR UNIT

CONSULT

  1. Replace the air bag diagnosis sensor unit. Refer to Removal and Installation.

  2. Ignition switch ON.

  3. Check for DTC.

Is DTC still current?

YES>>

GO TO 7.

NO>>

Clear DTC. Inspection End.

RELATED HARNESS

Replace the related harness.

>>

Inspection End.

B1000 Air Bag Diagnosis Sensor Unit Nissan Pathfinder 5th Gen

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC Detection Condition
B1000-49

Air bag diagnosis sensor unit

(Air bag diagnosis sensor unit)
Diagnosis condition Ignition switch ON.
Signal (terminal) —
Threshold Air bag diagnosis sensor unit is malfunctioning
Diagnosis delay time 2 seconds or more.
B1000-55

Air bag diagnosis sensor unit

(Air bag diagnosis sensor unit)
Diagnosis condition Ignition switch ON.
Signal (terminal) —
Threshold When no data are stored in the air bag diagnosis sensor unit
Diagnosis delay time 2 seconds or more.

POSSIBLE CAUSE

Malfunction in air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

CONSULT

  1. Ignition switch ON.

  2. Select “Self Diagnostic Result” mode of “AIR BAG”.

Is malfunctioning part detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

  1. Replace air bag diagnosis sensor unit. Refer to Removal and Installation.

  2. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

Check Intermittent incident. Refer to Intermittent Incident.

NO>>

Inspection End.

B1004 Passenger Air Bag Module Active Vent Nissan Pathfinder 2022

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC Detection Condition
B1004-1A

Passenger air bag module active vent

(Passenger air bag module active vent)
Diagnosis condition Ignition switch ON.
Signal (terminal) Passenger air bag module (active vent) signal
Threshold Passenger air bag module (active vent) circuits are shorted to each other
Diagnosis delay time 2 seconds or more.
B1004-1B

Passenger air bag module active vent

(Passenger air bag module active vent)
Diagnosis condition Ignition switch ON.
Signal (terminal) Passenger air bag module (active vent) signal
Threshold Passenger air bag module (active vent) circuit resistance is above threshold
Diagnosis delay time 2 seconds or more.
B1004-09

Passenger air bag module active vent

(Passenger air bag module active vent)
Diagnosis condition Ignition switch ON.
Signal (terminal) Passenger air bag module (active vent) signal
Threshold Passenger air bag module (active vent) circuit is shorted to other
Diagnosis delay time 2 seconds or more.
B1004-11

Passenger air bag module active vent

(Passenger air bag module active vent)
Diagnosis condition Ignition switch ON.
Signal (terminal) Passenger air bag module (active vent) signal
Threshold Passenger air bag module (active vent) circuit is shorted to ground
Diagnosis delay time 2 seconds or more.
B1004-12

Passenger air bag module active vent

(Passenger air bag module active vent)
Diagnosis condition When ignition switch is ON.
Signal (terminal) Passenger air bag module (active vent) signal
Threshold Passenger air bag module (active vent) circuit is shorted to power supply circuit
Diagnosis delay time 2 seconds or more.
B1004-55

Passenger air bag module active vent

(Passenger air bag module active vent)
Diagnosis condition Ignition switch ON.
Signal (terminal) Passenger air bag module (active vent) signal
Threshold When a mismatch is detected between in the configuration data stored in the air bag diagnosis sensor unit and Nissan Pathfinder vehicle specification.
Diagnosis delay time 2 seconds or more.

POSSIBLE CAUSE

  • Connection malfunction or open circuit of harness and connector

  • Internal malfunction of passenger air bag module (active vent)

  • Internal malfunction of air bag diagnosis sensor unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

CHECK SELF-DIAG RESULT

CONSULT

  1. Ignition switch ON.

  2. Select “Self Diagnostic Result” mode of “AIR BAG”.

Is malfunctioning part detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

Diagnosis Procedure

CHECK HARNESS CONNECTOR

Check the harness connector.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace harness connector.

CHECK WIRING HARNESS

Check the wiring harness externals.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Replace wiring harness.

REPLACE PASSENGER AIR BAG MODULE

  1. Replace passenger air bag module. Refer to Removal and Installation.

  2. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

GO TO 4.

NO>>

Inspection End.

REPLACE AIR BAG DIAGNOSIS SENSOR UNIT

  1. Replace air bag diagnosis sensor unit. Refer to Removal and Installation.

  2. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC detected?

YES>>

GO TO 1.

NO>>

Inspection End.