Dtc/circuit Diagnosis (P1220 Fuel Pump Control Module (fpcm) ... P1574 Ascd Vehicle Speed Sensor)

In this manual: Dtc/circuit Diagnosis (P1220 Fuel Pump Control Module (fpcm) ... P1574 Ascd Vehicle Speed Sensor)
General Information — 8Engine :: Engine Mechanical — 19Engine Lubrication System - Precautions. Preparation — 1Engine Lubrication System - Lubrication System (System Description). Engine Oil Pressure (Basic Inspection). Service Data and Specifications (SDS) — 1Engine Cooling System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Engine Cooling System - Engine Coolant — 1Engine Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Engine Control System - Ecu Diagnosis Information — 1Ecu Diagnosis Information - Ecm ++ — 1Engine Control System - Basic Inspection — 1Basic Inspection - Diagnosis and Repair Workflow ++ — 1Basic Inspection - Basic Inspection ++ — 1Basic Inspection - Additional Service When Replacing Ecm ++ — 1Basic Inspection - Fuel Pressure Check ++ — 1Basic Inspection - How to Set Srt Code ++ — 1Basic Inspection - How to Erase Permanent Dtc ++ — 1Engine Control System - Dtc/circuit Diagnosis — 1Engine Control System - Symptom Diagnosis — 1Engine Control System - Periodic Maintenance — 1Engine Control System - Removal and Installation — 1Fuel System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Fuel System - Fuel System (Periodic Maintenance). Fuel Level Sensor Unit (Disassembly and Assembly) — 1Exhaust System - Precautions. Preparation — 1Exhaust System - Exhaust System (Periodic Maintenance). Exhaust System (Removal and Installation) — 1Starting System - Precautions. Preparation. Starter Motor (Service Data and Specifications (sds)) — 1Starting System - Diagnosis and Repair Work Flow — 1Starting System - Starting System (Symptom Diagnosis). Starter Motor (Removal and Installation) — 1Accelerator Control System - Precautions. Service Data and Specifications (SDS) — 1Accelerator Control System - Accelerator Pedal Assembly — 1Transmission & Driveline :: Transaxle & Transmission — 21Driveline - System Description — 1Transfer: Ty92b - Ecu Diagnosis Information. Awd Control Unit ++ — 1Driveline - Basic Inspection — 1Driveline - Dtc/circuit Diagnosis — 1Driveline - Symptom Diagnosis — 1Driveline - Removal and Installation — 1Transfer: Ty92b - Unit Removal and Installation. Transfer Assembly ++ — 1Driveline - Unit Disassembly and Assembly — 1Driveline - Basic Inspection — 1Driveline - Removal and Installation — 1Driveline - Unit Disassembly and Assembly — 1Front Axle - Precautions. Preparation — 1Front Axle - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Front Axle - Front Drive Shaft Boot — 1Front Axle - Front Drive Shaft — 1Rear Axle - Precautions. Preparation. Service Data and Specifications (SDS) — 1Rear Axle - Noise, Vibration and Harshness (nvh) Troubleshooting — 1Rear Axle - Rear Drive Shaft — 1Suspension :: Front Suspension — 7Rear Suspension - Precautions. Preparation — 1Rear Suspension - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Rear Suspension - Rear Suspension Assembly — 1Road Wheels & Tires - Precautions — 1Road Wheels & Tires - Preparation. Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Road Wheels & Tires - System — 1Brakes :: Brake System — 9Parking Brake System - Precautions. Preparation — 1Parking Brake System - System — 1Vdc/tcs/abs - Precautions ++ — 1Brake Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Dtc/circuit Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Steering :: Steering System — 9Steering Control System - Precautions — 1Steering Control System - System — 1Steering Control System - Eps Control Unit (Ecu Diagnosis Information. Removal and Installation) — 1Restraints :: Seat Belt — 7Srs Air Bag - Precautions. Preparation — 1Srs Air Bag - Collision Diagnosis — 1Srs Air Bag - Occupant Classification System — 1Srs Air Bag Control System - Precautions — 1Srs Air Bag Control System - System — 1Srs Air Bag Control System - Diagnosis Sensor Unit — 1Srs Air Bag Control System - Inspection and Adjustment — 1Ventilation, Heater & Air Conditioner :: Ventilation System — 6Heater & Air Conditioning System - Precautions — 1Heater & Air Conditioning System - Preparation — 1Heater & Air Conditioning System - Component Parts — 1Heater & Air Conditioning System - Diagnosis and Repair Work Flow — 1Heater & Air Conditioning System - Compressor — 1Heater & Air Conditioning System - Cooler Pipe and Hose — 1Heater & Air Conditioning System - Condenser. Condenser — 1Heater & Air Conditioning System - Heating and Cooling Unit Assembly — 1Heater & Air Conditioning System - Service Data and Specifications (SDS) — 1Heater & Air Conditioning Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1Heater & Air Conditioning Control System - Ecu Diagnosis Information — 1Heater & Air Conditioning Control System - Basic Inspection — 1Heater & Air Conditioning Control System - Dtc/circuit Diagnosis — 1Heater & Air Conditioning Control System - Symptom Diagnosis — 1Heater & Air Conditioning Control System - Removal and Installation — 1Body Interior :: Interior — 8Instrument Panel - Precautions. Preparation. Clip List — 1Instrument Panel - Squeak and Rattle Trouble Diagnoses — 1Instrument Panel - Cluster Lid C — 1Seat - Precautions — 1Seat - Preparation. Clip List — 1Seat - Component Parts — 1Seat - System — 1Seat - Diagnosis and Repair Work Flow — 1Seat - Front Seat — 1Seat - Second Row Seats — 1Seat - Third Row Seats — 1Seat - Front Seat — 1Seat - Second Row Seat — 1Seat - Third Row Seat — 1Automatic Drive Positioner - Precautions. Preparation — 1Automatic Drive Positioner - System — 1Automatic Drive Positioner - Diagnosis and Repair Work Flow — 1Automatic Drive Positioner - Inspection and Adjustment — 1Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock — 38Security Control System - Precautions — 1Security Control System - System — 1Security Control System - Ecm, Bcm, Intelligent Key Unit, Ipdm E/r — 1Security Control System - Vehicle Security System Cannot Be Set — 1Glass & Window System - Precautions. Preparation — 1Glass & Window System - Squeak and Rattle Trouble Diagnoses — 1Power Window Control System - Precautions. Preparation — 1Power Window Control System - Power Supply and Ground Circuit — 1Power Window Control System - Power Window Motor Circuit — 1Power Window Control System - Front Power Window Rh Alone Does Not Operate — 1Power Window Control System - Rear Lh Side Power Window Alone Does Not Operate — 1Power Window Control System - Rear Rh Side Power Window Alone Does Not Operate — 1Roof - Precautions. Preparation — 1Roof - Power Supply and Ground Circuit — 1Roof - Moonroof Switch Assembly — 1Roof - Lin Communication Circuit — 1Roof - Auto Operation Does Not Operate — 1Roof - Anti-Pinch Function Does Not Operate — 1Exterior - Precautions. Preparation. Clip List (Preparation) — 1Exterior - Squeak and Rattle Trouble Diagnoses — 1Exterior - Fender Protector — 1Exterior - Over Fender — 1Exterior - Under Cover — 1Exterior - Roof Side Rail — 1Body Repair - Service Information — 1Service Information - Sheet Metal Work ++ — 1Service Information - Body Welding and Precautions ++ — 1Service Information - Safety and Health ++ — 1Service Information - Repairing Procedures and Precautions ++ — 1Body Repair - Precaution — 1Body Repair - Preparation — 1Body Repair - Removal and Installation — 1Driver Controls :: Mirrors — 8Exterior Lighting System - System Description — 1System Description - Component Parts ++ — 1Exterior Lighting System - Basic Inspection — 1Exterior Lighting System - Dtc/circuit Diagnosis — 1Exterior Lighting System - Symptom Diagnosis — 1Exterior Lighting System - Periodic Maintenance — 1Exterior Lighting System - Removal and Installation — 1Interior Lighting System - Precautions. Preparation — 1Interior Lighting System - Component Parts. Interior Lighting System — 1Interior Lighting System - System — 1Interior Lighting System - Diagnosis and Repair Work Flow — 1Interior Lighting System - Interior Lighting System Symptoms (Symptom Diagnosis). Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Interior Lighting System - Foot Lamp — 1Wiper & Washer - Precautions — 1Wiper & Washer - Preparation. Bcm, Ipdm E/r (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Wiper & Washer - System — 1Wiper & Washer - Diagnosis and Repair Work Flow — 1Defogger - Precautions. Bcm, A/c Auto Amp. (Ecu Diagnosis Information) — 1Defogger - Diagnosis and Repair Work Flow — 1Horn - Precautions — 1Electrical & Power Control :: Power Outlet — 13Body Control System - Precautions. Preparation — 1Body Control System - Component Parts — 1Body Control System - System — 1Body Control System - Diagnosis System (bcm) — 1Body Control System - Bcm — 1Lan System - System Description — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - Removal and Installation — 1Charging System - Precautions. Preparation. Ecm, Ipdm E/r (Ecu Diagnosis Information) — 1Charging System - Diagnosis and Repair Work Flow — 1Charging System - Charging System (Symptom Diagnosis). Generator (Removal and Installation). Service Data and Specifications (SDS) — 1Power Supply, Ground & Circuit Elements - Precautions. Preparation. Service Data and Specifications (SDS) — 1Driver Information & Multimedia :: Meter, Warning Lamp & Indicator — 25Warning Chime System - Application Notice (How to Use This Manual). Precautions — 1Warning Chime System - System — 1Warning Chime System - Diagnosis System (combination Meter) — 1Warning Chime System - Bcm, Combination Meter (Ecu Diagnosis Information). Diagnosis and Repair Work Flow (Basic Inspection) — 1Sonar System - Precautions. Preparation — 1Sonar System - Sonar Control Unit — 1Dtc/circuit Diagnosis - B2720 Corner Sensor [rl] ++ — 1Audio, Visual & Navigation System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Multi Av (av Control Unit) ++ — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Symptom Diagnosis - Multi Av System ++ — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Cruise Control & Driver Assistance :: Cruise Control System — 17Driver Assistance System - System Description — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Driver Assistance System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1System Description - Handling Precaution ++ — 1Driver Assistance System - Ecu Diagnosis Information — 1Driver Assistance System - Basic Inspection — 1Basic Inspection - Distance Sensor Alignment ++ — 1Basic Inspection - Camera Aiming Adjustment ++ — 1Basic Inspection - Action Test ++ — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Laser/radar (distance Sensor) ++ — 1Dtc/circuit Diagnosis - Lane Camera (front Camera Unit) ++ — 1Driver Assistance System - Symptom Diagnosis — 1Driver Assistance System - Removal and Installation — 1Driver Assistance System - System Description — 1System Description - System ++ — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Drive Mode System - Precautions — 1Drive Mode System - Component Parts. Drive Mode System — 1Drive Mode System - System — 1Drive Mode System - Diagnosis and Repair Work Flow — 1Drive Mode System - Drive Mode Select Switch Circuit — 1Maintenance - Precautions. Preparation — 1Maintenance - General Maintenance — 1Maintenance - Periodic Maintenance — 1Maintenance - Recommended Fluids and Lubricants — 1Maintenance - Engine Maintenance — 1Maintenance - Chassis and Body Maintenance — 1Engine Lubrication System - Periodic Maintenance — 1Engine Lubrication System - Removal and Installation — 1Engine Cooling System - System Description — 1Engine Cooling System - Removal and Installation — 1Engine Control System - Vq35dd — 1Fuel System - Removal and Installation — 1Starting System - System Description — 1Starting System - Dtc/circuit Diagnosis — 1Driveline - Transfer: Ty92b — 1Driveline - Rear Propeller Shaft: 3fcj-Cvj — 1Driveline - Rear Final Drive: R145 — 1Front Axle - Periodic Maintenance — 1Front Axle - Removal and Installation — 1Rear Axle - Periodic Maintenance — 1Rear Axle - Removal and Installation — 1Rear Suspension - Removal and Installation — 1Road Wheels & Tires - System Description — 1Road Wheels & Tires - Basic Inspection — 1Road Wheels & Tires - Dtc/circuit Diagnosis — 1Road Wheels & Tires - Symptom Diagnosis — 1Road Wheels & Tires - Periodic Maintenance — 1Road Wheels & Tires - Removal and Installation — 1Parking Brake System - System Description — 1Parking Brake System - Basic Inspection — 1Parking Brake System - Dtc/circuit Diagnosis — 1Parking Brake System - Symptom Diagnosis — 1Parking Brake System - Removal and Installation — 1Brake Control System - Vdc/tcs/abs — 1Brake Control System - Automatic Brake Hold — 1Brake Control System - Automatic Emergency Braking — 1Brake Control System - Rear Automatic Braking — 1Steering Control System - System Description — 1Steering Control System - Basic Inspection — 1Steering Control System - Dtc/circuit Diagnosis — 1Steering Control System - Symptom Diagnosis — 1Srs Air Bag - Removal and Installation — 1Srs Air Bag Control System - System Description — 1Srs Air Bag Control System - Basic Inspection — 1Srs Air Bag Control System - Symptom Diagnosis — 1Heater & Air Conditioning System - Symptom Diagnosis — 1Heater & Air Conditioning System - Periodic Maintenance — 1Heater & Air Conditioning Control System - Automatic Air Conditioning — 1Instrument Panel - Removal and Installation — 1Instrument Panel - Unit Disassembly and Assembly — 1Seat - Ecu Diagnosis Information — 1Seat - Dtc/circuit Diagnosis — 1Seat - Symptom Diagnosis — 1Automatic Drive Positioner - System Description — 1Automatic Drive Positioner - Ecu Diagnosis Information — 1Automatic Drive Positioner - Dtc/circuit Diagnosis — 1Automatic Drive Positioner - Symptom Diagnosis — 1Automatic Drive Positioner - Removal and Installation — 1Security Control System - System Description — 1Security Control System - Basic Inspection — 1Security Control System - Dtc/circuit Diagnosis — 1Security Control System - Symptom Diagnosis — 1Security Control System - Removal and Installation — 1Glass & Window System - Removal and Installation — 1Power Window Control System - System Description — 1Power Window Control System - Ecu Diagnosis Information — 1Power Window Control System - Basic Inspection — 1Power Window Control System - Dtc/circuit Diagnosis — 1Power Window Control System - Symptom Diagnosis — 1Power Window Control System - Removal and Installation — 1Roof - System Description — 1Roof - Ecu Diagnosis Information — 1Roof - Basic Inspection — 1Roof - Dtc/circuit Diagnosis — 1Roof - Symptom Diagnosis — 1Roof - Removal and Installation — 1Exterior - System Description — 1Exterior - Removal and Installation — 1Body Repair - Repair Information — 1Exterior Lighting System - Led Headlamp — 1Interior Lighting System - Dtc/circuit Diagnosis — 1Interior Lighting System - Removal and Installation — 1Wiper & Washer - System Description — 1Wiper & Washer - Dtc/circuit Diagnosis — 1Wiper & Washer - Symptom Diagnosis — 1Wiper & Washer - Removal and Installation — 1Defogger - System Description — 1Defogger - Dtc/circuit Diagnosis — 1Defogger - Symptom Diagnosis — 1Defogger - Removal and Installation — 1Horn - Removal and Installation — 1Body Control System - Basic Inspection — 1Body Control System - Dtc/circuit Diagnosis — 1Body Control System - Symptom Diagnosis — 1Body Control System - Removal and Installation — 1Lan System - Can Fundamental — 1Lan System - Can — 1Lan System - Can Gateway — 1Power Control System - Ipdm E/r — 1Power Control System - Power Distribution System — 1Charging System - System Description — 1Charging System - Dtc/circuit Diagnosis — 1Power Supply, Ground & Circuit Elements - System Description — 1Power Supply, Ground & Circuit Elements - Basic Inspection — 1Power Supply, Ground & Circuit Elements - Removal and Installation — 1Warning Chime System - System Description — 1Warning Chime System - Dtc/circuit Diagnosis — 1Warning Chime System - Symptom Diagnosis — 1Sonar System - System Description — 1Sonar System - Basic Inspection — 1Sonar System - Dtc/circuit Diagnosis — 1Sonar System - Symptom Diagnosis — 1Sonar System - Removal and Installation — 1Audio, Visual & Navigation System - Nissanconnect — 1Audio, Visual & Navigation System - Intelligent Around View Monitor System — 1Audio, Visual & Navigation System - Rear View Monitor System — 1Audio, Visual & Navigation System - Telematics System — 1Driver Assistance System - Adas Control Unit 2 — 1Driver Assistance System - Driver Assistance System — 1Driver Assistance System - Chassis Control — 1Drive Mode System - Removal and Installation — 1Dtc/circuit Diagnosis (C053c Wheel Speed Sensor ... U2141 Can Comm Circuit) — 1Dtc/circuit Diagnosis (P0011 Intake Valve Timing Control ... P0111 Iat Sensor) — 1Dtc/circuit Diagnosis (P0116 Engine Coolant Temperature Sensor ... P025b Fuel Pump Module a) — 1Dtc/circuit Diagnosis (P026b Injection Timing ... P0420 Three Way Catalyst Function) — 1Dtc/circuit Diagnosis (P0441 Evap Control System ... P0524 Engine Oil Pressure) — 1Dtc/circuit Diagnosis (P0532 A/c Refrigerant Pressure Sensor ... P064d Ecm) — 1Dtc/circuit Diagnosis (P06da Engine Oil Pressure Control Solenoid Valve ... P1217 Engine Over Temperature) — 1Dtc/circuit Diagnosis (P1220 Fuel Pump Control Module (fpcm) ... P1574 Ascd Vehicle Speed Sensor) — 1Dtc/circuit Diagnosis (P1575 Brake Switch ... P2101 Electric Throttle Control Function) — 1Dtc/circuit Diagnosis (P2118 Throttle Control Motor ... P34ac Electric Intake Valve Timing Control Actuator) — 1Dtc/circuit Diagnosis (Active Grille Shutter ... High Pressure Fuel Pump) — 1Dtc/circuit Diagnosis (Ignition Signal ... Variable Induction Air System) — 14012 C1040 Emergency Brake — 14013 C106a Wheel Sensor — 14014 C1078-55 Not Configuration — 14015 C10b4-98 Overheat — 14016 B1001 Lap Pre-Tensioner Lh — 14017 B0001 Driver Air Bag Module — 14018 B100e Knee Air Bag Module Rh — 14019 B142x Collision Detection — 1Dtc/circuit Diagnosis (B20c7-11 A/c Clutch ... B24a6-11 in-Vehicle Sensor) — 1Dtc/circuit Diagnosis (B24a6-15 in-Vehicle Sensor ... U2140-87 Can Comm Err (ecm)) — 1Dtc/circuit Diagnosis (C1f00-1c Control Unit ... C1f04-61 Brake Sw/stop Lamp Sw) — 1Dtc/circuit Diagnosis (C1f05-49 Front Camera Unit ... C1f70-87 Ethernet Circuit) — 1
133steps
~798min
5/5difficulty
Done 0 of 133
  • P1220 Fuel Pump Control Module (fpcm)
  • P1225 Tp Sensor
  • P12a9 Hvac Communication
  • P1526 Ascd System
  • P155b Energy Management Control
  • P155d Generator
  • P1564 Ascd Steering Switch
  • P1568 Icc Function
  • P1572 Brake Pedal Position Switch
  • P1574 Ascd Vehicle Speed Sensor

P1220 Fuel Pump Control Module (fpcm) Nissan Pathfinder SUV

DTC Description

DTC DETECTION LOGIC

DTC No.

Trouble diagnosis name

(Trouble diagnosis content)
DTC detecting condition
P1220 00

FPCM/CIRCUIT

(Fuel pump control module)
Diagnosis condition Engine cranking
Signal (terminal) Fuel pump control module signal
Threshold A signal voltage of the FPCM to the ECM is too low
Diagnosis delay time -

POSSIBLE CAUSE

  • Harness or connectors

    (FPCM circuit is open or shorted)

    (Fuel pump circuit is open or shorted)

  • FPCM

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

  • Before performing the following procedure, confirm that battery voltage is between 12 - 15 V at idle.

  • Before performing the following procedure, check that the engine coolant temperature is −10 °C or more.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and let it idle for at least 5 seconds.

    If engine does not start, crank engine for at least 5 seconds.

  2. Check DTC.

Is DTC detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

INSPECTION END

Diagnosis Procedure

CHECK FUEL PUMP RELAY POWER SUPPLY

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Turn ignition switch ON.

  4. Check the voltage between ECM harness connector terminals.

    ECM Voltage
    Connector + Connector -
    Terminal Terminal
    F78 84 F79 87 Battery voltage

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 2.

CHECK FUEL PUMP RELAY POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect IPDM E/R harness connector.

  3. Check the continuity between ECM harness connector and IPDM E/R harness connector.

    + − Continuity
    ECM IPDM E/R
    Connector Terminal Connector Terminal
    F78 84 F24 76 Existed
  4. Also check harness for short to ground.

Is the inspection result normal?

YES>>

Perform the trouble diagnosis for power supply circuit.

NO>>

Repair or replace error-detected parts.

CHECK FPCM POWER SUPPLY

  1. Turn ignition switch OFF.

  2. Reconnect ECM harness connector.

  3. Disconnect FPCM harness connector.

  4. Turn ignition switch ON.

  5. Check the voltage between FPCM harness connector and ground.

    FPCM Ground Voltage
    Connector Terminal
    B58 1 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

GO TO 4.

CHECK FPCM POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect IPDM E/R harness connector.

  3. Check the continuity between FPCM harness connector and IPDM E/R harness connector.

    + − Continuity
    FPCM IPDM E/R
    Connector Terminal Connector Terminal
    B58 1 E121 46 Existed
  4. Also check harness for short to ground.

Is the inspection result normal?

YES>>

Perform the trouble diagnosis for power supply circuit.

NO>>

Repair or replace error-detected parts.

CHECK FPCM GROUND CIRCUIT FOR OPEN AND SHORT

  1. Turn ignition switch OFF.

  2. Check the continuity between FPCM harness connector and ground.

    FPCM Ground Continuity
    Connector Terminal
    B58 4 Ground Existed
  3. Also check harness for short to power.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair open circuit or short to power in harness or connectors.

CHECK FPCM INPUT AND OUTPUT CIRCUITS FOR OPEN AND SHORT

  1. Disconnect ECM harness connector.

  2. Check the continuity between FPCM harness connector and ECM harness connector.

    FPCM ECM Continuity
    Connector Terminal Connector Terminal
    B58 2 E32 188 Existed
    3 182
  3. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

GO TO 7.

DETECT MALFUNCTIONING PART

Check the following.

  • Harness for open or short between FPCM and ECM

  • Loose or poor connection for each connector and harness

>>

Repair open circuit, short to ground or short to power in harness or connectors.

CHECK FUEL PUMP CONTROL CIRCUIT FOR OPEN AND SHORT

  1. Disconnect fuel level sensor unit and fuel pump harness connector.

  2. Check the continuity between FPCM harness connector and fuel level sensor unit and fuel pump harness connector.

    FPCM Fuel level sensor unit and fuel pump Continuity
    Connector Terminal Connector Terminal
    B58 5 B57 7 Existed
    6 8
  3. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Repair open circuit, short to ground or short to power in harness or connectors.

CHECK FPCM

Refer to Component Inspection (FPCM).

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Replace FPCM.

CHECK INTERMITTENT INCIDENT

Refer to Intermittent Incident.

>>

INSPECTION END

Component Inspection (FPCM)

CHECK FUEL PUMP CONTROL MODULE (FPCM)

  1. Check the voltage between FPCM terminals under the following conditions.

    FPCM Condition Voltage
    Connector + −
    Terminal Terminal
    B58 5 6 For 1 second after turning ignition switch ON Approx. 8.5 V
    More than 1 second after turning ignition switch ON Approx. 0 V
    Idle speed Approx. 8.5 V

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace FPCM.

P1225 Tp Sensor Nissan Pathfinder

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P1225 00

CTP LEARNING-B1

(Closed throttle position learning bank 1)
Diagnosis condition Ignition switch ON
Signal (terminal) —
Threshold Closed throttle position learning value is excessively low
Diagnosis delay time —

POSSIBLE CAUSE

Electric throttle control actuator (TP sensor 1 and 2)

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 10 V at idle.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON.

  2. Turn ignition switch OFF and wait at least 10 seconds.

  3. Turn ignition switch ON.

  4. Check 1st trip DTC.

Is DTC P1225 detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK ELECTRIC THROTTLE CONTROL ACTUATOR VISUALLY

  1. Turn ignition switch OFF.

  2. Remove air duct and resonator assembly. Refer to Exploded View.

  3. Check if foreign matter is caught between the throttle valve and the housing.

Is the inspection result normal?

YES>>

Replace malfunctioning electric throttle control actuator. Refer to Exploded View.

NO>>
  1. Remove the foreign matter and clean the electric throttle control actuator inside.

  2. Perform throttle valve closed position leaning. Refer to Description.

P12a9 Hvac Communication Nissan Pathfinder

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P12A9 00

HVAC communication

(HVAC communication)
Diagnosis condition Engine speed less than 650 rpm
Signal (terminal) CAN communication signal
Threshold When the ambient temperature estimated from the intake air temperature and engine coolant temperature is lower than 0℃
Diagnosis delay time 5 seconds

POSSIBLE CAUSE

A/C auto amp.

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 12 V or more at idle.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine.

  2. Set the select lever in P or N range and wait at least 30 seconds.

  3. Check DTC.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK CAN COMMUNICATION LINE

Check CAN communication line. Refer to Trouble Diagnosis Flow Chart.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts.

CHECK DTC WITH A/C AUTO AMP.

Check DTC with A/C auto amp. Refer to DTC Index.

Is DTC detected?

YES>>

Perform trouble shooting relevant to DTC indicated.

NO>>

INSPECTION END

P1526 Ascd System Nissan Pathfinder Fifth generation

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P1526 00

Nissan Pathfinder Vehicle speed sensor

(Vehicle speed sensor)
Diagnosis condition Ignition switch ON
Signal CAN communication signal
Threshold ECM cannot receive a communication signal sent from VDC (Nissan Pathfinder vehicle dynamics control system)
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Harness or connectors (The CAN communication line is open or shorted.)

  • VDC(Nissan Pathfinder vehicle dynamics control system)

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON and wait at least 3 seconds.

  2. Check DTC.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

Perform the trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

P155b Energy Management Control Nissan Pathfinder 5th Gen

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P155B 00

Electrical energy management system

(Electrical energy management system)
Diagnosis condition Ignition switch ON
Signal (terminal) ECM power supply
Threshold Battery voltage measured by ECM below or above threshold.
Diagnosis delay time 20 seconds or more

POSSIBLE CAUSE

  • Harness or connectors

  • ECM

  • IPDM E/R

  • Battery

  • Generator

FAIL-SAFE

Not applicable

CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC P155B is displayed with DTC P155E and P155F first perform the trouble diagnosis for DTC P155E andP155F.

Which DTC is detected?

YES>>

Perform diagnosis of applicable.

  • DTC P155E: Refer to DTC Description.

  • DTC P155F: Refer to DTC Description.

NO>>

GO TO 2.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Ignition switch OFF and wait at least 10 seconds.

  2. Ignition switch ON.

  3. Ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.

>>

GO TO 3.

DTC CONFIRMATION PROCEDURE

  1. Start engine and let it idle for at least 20 seconds.

  2. Check DTC.

Which DTC is detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK CHARGE SYSTEM

Check charge system. Refer to Work Flow (Without 165–DSS-5000P) or Work Flow (With 165–DSS-5000P).

Which DTC is detected?

YES>>

INSPECTION END

NO>>

Repair or replace the error-detected parts.

P155d Generator Nissan Pathfinder 5th Gen

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P155D 00 GENERATOR A Diagnosis condition Engine running at idle
Signal (terminal) Generator mechanical malfunction signal
Threshold ECM receives mechanical malfunction signal sent from generator
Diagnosis delay time —
B Diagnosis condition Engine running at idle
Signal (terminal) Generator electrical malfunction signal
Threshold ECM receives electrical malfunction signal sent from generator
Diagnosis delay time —

POSSIBLE CAUSE

Generator

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted. always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine and let it idle at least 10 seconds.

  2. Check DTC.

Is DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK CHARGING SYSTEM

Perform trouble diagnosis for charging system. Refer to Work Flow (Without 165–DSS-5000P) or Work Flow (With 165–DSS-5000P).

Is the inspection result normal?

YES>>

Replace generator. Refer to Removal and Installation.

NO>>

Repair or replace error-detected parts.

P1564 Ascd Steering Switch Nissan Pathfinder 2022

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P1564 00

ASCD SW

(ASCD steering switch)
Diagnosis condition Ignition switch ON
Signal (terminal) ASCD steering switch signal
Threshold
  • An excessively high voltage signal from the ASCD steering switch is sent to ECM

  • ECM detects that input signal from the ASCD steering switch is out of the specified range

  • ECM detects that the ASCD steering switch is stuck ON

Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors (ASCD steering switch circuit is open or shorted.)

  • ASCD steering switch

  • ECM

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

CHECK DTC PRIORITY

If DTC P1564 is displayed with DTC P0605, first perform the confirmation procedure (trouble diagnosis) for DTC P0605.

Is DTC P0605 detected?

YES>>

Perform diagnosis for P0605. Refer to DTC Description.

NO>>

GO TO 2.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON and wait at least 10 seconds.

  2. Press MAIN switch for at least 10 seconds, then release it and wait at least 10 seconds.

  3. Press CANCEL switch for at least 10 seconds, then release it and wait at least 10 seconds.

  4. Press ACCEL/RES switch for at least 10 seconds, then release it and wait at least 10 seconds.

  5. Press COAST/SET switch for at least 10 seconds, then release it and wait at least 10 seconds.

  6. Check DTC.

Is DTC P1564 detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P1564 is displayed with DTC P0605, first perform the confirmation procedure (trouble diagnosis) for DTC P0605.

Is DTC P0605 detected?

YES>>

Perform diagnosis for P0605. Refer to DTC Description.

NO>>

GO TO 2.

CHECK ASCD STEERING SWITCH CIRCUIT

With CONSULT

  1. Turn ignition switch ON.

  2. On CONSULT screen, select “ENGINE”>>“Data Monitor”>>“MAIN SW”, “CANCEL SW”, “RESUME/ACC SW” and “SET SW”.

  3. Check each item indication under the following conditions.

    Monitor item Condition Indication
    MAIN SW MAIN switch Pressed ON
    Released OFF
    CANCEL SW CANCEL switch Pressed ON
    Released OFF
    RESUME/ACC SW ACCEL/RES switch Pressed ON
    Released OFF
    SET SW COAST/SET switch Pressed ON
    Released OFF

Without CONSULT

  1. Turn ignition switch ON.

  2. Check the voltage between ECM harness connector terminals as per the following.

    ECM Condition

    Voltage

    (Approx.)
    Connector + –
    Terminal
    E32

    186

    (ASCD steering switch signal)
    187 MAIN switch: Pressed 0 V
    CANCEL switch: Pressed 1 V
    COAST/SET switch: Pressed 2 V
    ACCEL/RES switch: Pressed 3 V
    All ASCD steering switches: Released 4 V

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

GO TO 3.

CHECK ASCD STEERING SWITCH GROUND CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Disconnect combination switch (spiral cable) harness connector.

  4. Check the continuity between combination switch harness and ECM harness connector.

    Combination switch ECM Continuity
    Connector Terminal Connector Terminal
    M30 1 E32 187 Existed
  5. Also check harness for short to power.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts.

CHECK ASCD STEERING SWITCH INPUT SIGNAL CIRCUIT

  1. Check the continuity between combination switch (spiral cable) harness connector and ECM harness connector.

    Combination switch ECM Continuity
    Connector Terminal Connector Terminal
    M30 8 E32 186 Existed
  2. Also check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace error-detected parts.

CHECK COMBINATION SWITCH

Check the continuity between combination switch (spiral cable) connector terminals.

Combination switch Continuity
Terminal
21 8 Existed
36 1

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Replace spiral cable. Refer to Removal and Installation.

CHECK ASCD STEERING SWITCH

Refer to Component Inspection.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace ASCD steering switch. Refer to Removal and Installation.

Component Inspection

CHECK ASCD STEERING SWITCH

  1. Turn ignition switch OFF.

  2. Disconnect combination switch (spiral cable) harness connector M149.

  3. Check resistance between combination switch harness connector terminals under the following conditions.

    Combination switch Condition

    Resistance

    (Approx.)
    Connector Terminals
    M149 21 36 MAIN switch: Pressed 0 Ω
    CANCEL switch: Pressed 250 Ω
    COAST/SET switch: Pressed 660 Ω
    ACCEL/RES switch: Pressed 1,480 Ω
    All ASCD steering switches: Released 4,000 Ω

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace ASCD steering switch. Refer to Removal and Installation.

P1568 Icc Function Nissan Pathfinder 5th Gen

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P1568 00

ICC COMMAND VALUE

(ICC function)
Diagnosis condition —
Signal (terminal) ADAS control unit 2 signal
Threshold ECM detects a difference between signals from ADAS control unit 2 is out of specified range
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors (CAN communication line is open or shorted.)

  • ADAS control unit 2

  • ECM

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

CHECK DTC PRIORITY

If DTC P1568 is displayed with DTC UXXXX, P0605 or P0607, first perform the confirmation procedure for DTC UXXXX, P0605 or P0607.

Is DTC UXXXX, P0605 or P0607 detected?

YES>>

Perform diagnosis of applicable.

  • DTC UXXXX: Refer to DTC Index.

  • DTC P0605: Refer to DTC Description.

  • DTC P0607: Refer to DTC Description.

NO>>

GO TO 2.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Step 4 may be conducted with the drive wheels lifted in the shop or by driving the Nissan Pathfinder vehicle. If a road test is expected to be easier, it is unnecessary to lift the vehicle.

>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON.

  2. Press MAIN switch on ICC steering switch.

  3. Drive the Nissan Pathfinder vehicle at more than 40 km/h.

  4. Press SET/COAST switch.

  5. Check DTC.

Is DTC P1568 detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P1568 is displayed with DTC UXXXX, P0605 or P0607, first perform the confirmation procedure for DTC UXXXX, P0605 or P0607.

Is DTC UXXXX, P0605 or P0607 detected?

YES>>

Perform diagnosis of applicable.

  • DTC UXXXX: Refer to DTC Index.

  • DTC P0605: Refer to DTC Description.

  • DTC P0607: Refer to DTC Description.

NO>>

GO TO 2.

REPLACE ADAS CONTROL UNIT 2

  1. Replace ADAS control unit 2.

  2. Perform Work Procedure.

  3. Check DTC of ADAS control unit 2. Refer to CONSULT Function (ICC/ADAS 2)(Without ProPILOT system) or CONSULT Function (ICC/ADAS 2) (With ProPILOT system).

>>

INSPECTION END

P1572 Brake Pedal Position Switch Nissan Pathfinder R53

DTC Description

When the brake pedal is depressed, brake pedal position switch is turned OFF and stop lamp switch is turned ON. ECM detects the state of the brake pedal by those two types of input (ON/OFF signal).

Refer to System Description for the ASCD function.

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P1572 00

ASCD BRAKE SW

(Brake pedal position switch)
Diagnosis condition Selector lever Suitable position and engine run
Signal (terminal) Brake pedal position switch signal
Threshold Brake pedal position switch signal is not sent to ECM for extremely long time
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors (Brake pedal position switch circuit is shorted.)

  • Brake pedal position switch

  • Incorrect brake pedal position switch installation

  • ECM

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

CHECK DTC PRIORITY

If DTC P1572 is displayed with DTC P0605, first perform the confirmation procedure (trouble diagnosis) for DTC P0605.

Is DTC P0605 detected?

YES>>

Perform diagnosis for P0605. Refer to DTC Description.

NO>>

GO TO 2.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine (VDC switch OFF).

  2. Press MAIN switch and make sure that CRUISE lamp illuminates.

  3. Drive the Nissan Pathfinder vehicle for at least 5 consecutive seconds under the following conditions.

    Nissan Pathfinder Vehicle speed More than 30 km/h
    Selector lever Suitable position
  4. Check DTC.

Is DTC P1572 detected?

YES>>

Proceed to Diagnosis Procedure.

NO>>

GO TO 4.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Drive the Nissan Pathfinder vehicle for at least 5 consecutive seconds under the following conditions.

    Nissan Pathfinder Vehicle speed More than 30 km/h
    Selector lever Suitable position
    Driving location Depress the brake pedal for more than 5 seconds so as not to come off from the above-mentioned Nissan Pathfinder vehicle speed.
  2. Check DTC.

Is DTC P1572 detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P1572 is displayed with DTC P0605, first perform the confirmation procedure (trouble diagnosis) for DTC P0605.

Is DTC P0605 detected?

YES>>

Perform diagnosis for P0605. Refer to DTC Description.

NO>>

GO TO 2.

CHECK OVERALL FUNCTION

With CONSULT

  1. Turn ignition switch ON.

  2. Select “BRAKE SW1” and “BRAKE SW2” in “DATA MONITOR” mode of “ENGINE” using CONSULT.

  3. Check “BRAKE SW1” and “BRAKE SW2” indication as per the following conditions.

    Monitor item Condition Indication
    BRAKE SW1 Brake pedal Slightly depressed OFF
    Fully released ON
    BRAKE SW2 Brake pedal Slightly depressed ON
    Fully released OFF

Without CONSULT

  1. Turn ignition switch ON.

  2. Check the voltage between ECM harness connector terminals as per the following.

    ECM Condition

    Voltage

    (Approx.)
    Connector + –
    Terminal
    E32

    192

    (Brake pedal position switch signal)
    204 Brake pedal Slightly depressed 0 V
    Fully released Battery voltage

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

GO TO 3.

CHECK BRAKE PEDAL POSITION SWITCH POWER SUPPLY

  1. Turn ignition switch OFF.

  2. Disconnect brake pedal position switch harness connector.

  3. Turn ignition switch ON.

  4. Check the voltage between brake pedal position switch harness connector and ground.

    + − Voltage
    Brake pedal position switch
    Connector Terminal
    E76 1 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

GO TO 4.

CHECK BRAKE PEDAL POSITION SWITCH POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect fuse block (J/B) harness connector.

  3. Check the continuity between brake pedal position switch harness connector and fuse block (J/B) harness connector.

    Brake pedal position switch Fuse block (J/B) Continuity
    Connector Terminal Connector Terminal
    E76 1 E55 7J Existed
  4. Also check harness for short to ground.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace error-detected parts.

CHECK FUSE

Check that the following fuse is not blowing.

Location Fuse No. Capacity
Fuse block (J/B) #32 10A

Is the fuse blown (open)?

YES>>

Replace the fuse after repairing the applicable circuit.

NO>>

Perform trouble diagnosis for power supply circuit.

CHECK BRAKE PEDAL POSITION SWITCH INPUT SIGNAL CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between brake pedal position switch harness connector and ECM harness connector.

    Brake pedal position switch ECM Continuity
    Connector Terminal Connector Terminal
    E76 2 E32 192 Existed
  4. Also check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair or replace error-detected parts.

CHECK BRAKE PEDAL POSITION SWITCH

Refer to Component Inspection (Brake Pedal Position Switch)

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace brake pedal position switch. Refer to Exploded View.

Component Inspection (Brake Pedal Position Switch)

CHECK BRAKE PEDAL POSITION SWITCH-I

  1. Turn ignition switch OFF.

  2. Disconnect brake pedal position harness connector.

  3. Check the continuity between brake pedal position switch terminals as per the following conditions.

    Brake pedal position switch Condition Continuity
    Terminal
    1 2 Brake pedal Fully released Existed
    Slightly depressed Not existed

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

GO TO 2.

CHECK BRAKE PEDAL POSITION SWITCH-II

  1. Adjust brake pedal position switch installation. Refer to Adjustment.

  2. Check the continuity between brake pedal position switch terminals as per the following conditions.

    Brake pedal position switch Condition Continuity
    Terminal
    1 2 Brake pedal Fully released Existed
    Slightly depressed Not existed

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace brake pedal position switch. Refer to Exploded View.

P1574 Ascd Vehicle Speed Sensor Nissan Pathfinder 2026

DTC Description

The ECM receives two vehicle speed signals via the CAN communication line. One is sent from “combination meter”, and the other is from TCM (Transmission control module). The ECM uses these signals for ASCD control. Refer to System Description for ASCD functions.

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P1574 00

ASCD VHL SPD SEN

(ASCD Nissan Pathfinder vehicle speed sensor)
Diagnosis condition Nissan Pathfinder Vehicle speed: More than 40 km/h
Signal (terminal) —
Threshold The difference between the two Nissan Pathfinder vehicle speed signals is out of the specified range
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors (CAN communication line is open or shorted.)

  • Combination meter

  • ABS actuator and electric unit (control unit)

  • Wheel sensor

  • TCM

  • ECM

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

CHECK DTC PRIORITY

If DTC P1574 is displayed with DTC UXXXX, P0500, P0605 or P0607, first perform the confirmation procedure (trouble diagnosis) for DTC UXXXX, P0500, P0605 or P0607.

Is DTC UXXXX, P0500, P0605 or P0607 detected?

YES>>

Perform diagnosis of applicable.

  • DTC UXXXX: Refer to DTC Index.

  • DTC P0500: Refer to DTC Description.

  • DTC P0605: Refer to DTC Description.

  • DTC P0607: Refer to DTC Description.

NO>>

GO TO 2.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine (VDC switch OFF).

  2. Drive the Nissan Pathfinder vehicle at more than 40 km/h.

  3. Check DTC.

Is DTC P1574 detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P1574 is displayed with DTC UXXXX, P0500, P0605 or P0607, first perform the confirmation procedure (trouble diagnosis) for DTC UXXXX, P0500, P0605 or P0607.

Is DTC UXXXX, P0500, P0605 or P0607 detected?

YES>>

Perform diagnosis of applicable.

  • DTC UXXXX: Refer to DTC Index.

  • DTC P0500: Refer to DTC Description.

  • DTC P0605: Refer to DTC Description.

  • DTC P0607: Refer to DTC Description.

NO>>

GO TO 2.

CHECK DTC WITH TCM

Check DTC with TCM. Refer to CONSULT Function.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Perform trouble shooting relevant to DTC indicated.

CHECK DTC WITH ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)

Check DTC with ABS actuator and electric unit (control unit). Refer to CONSULT Function.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace.

CHECK DTC WITH COMBINATION METER

Check DTC with combination meter.

  • FULL TFT METER: Refer to CONSULT Function (METER/M&A).

  • 7 INCH INFORMATION DISPLAY: Refer to CONSULT Function (METER/M&A).

>>

INSPECTION END