Driveline - Unit Disassembly and Assembly
- Transfer Cover
- Ring Gear Shaft
- Drive Pinion
- Transfer Case
Transfer Cover Nissan Pathfinder SUV
Exploded View

| 1. | Transfer cover dust seal | 2. | Transfer cover | 3. | Filler plug |
| 4. | Gasket | 5. | Transfer cover oil seal | 6. | O-ring |
| 7. | Ring gear bearing adjusting shim (transfer cover side) | 8. | Ring gear bearing (transfer cover side) | 9. | Gasket |
| 10. | Transfer oil temperature sensor | 11. | Ring gear shaft | 12. | Ring gear |
| 13. | Ring gear bearing (transfer case side) | 14. | Baffle plate | 15. | Snap ring |
| 16. | Ring gear bearing outer race (transfer case side) | 17. | Ring gear bearing adjusting shim (transfer case side) | 18. | Transfer case |
| 19. | Drain plug | 20. | Plug | 21. | O-ring |
| 22. | Oil seal | 23. | Dowel pin | 24. | Drive pinion |
| 25. | Drive pinion adjusting shim | 26. | O-ring | 27. | Pinion bearing assembly |
| 28. | Oil seal | 29. | Dust cover | 30. | Companion flange |
| 31. | Pinion lock nut | A. | Oil seal lip | B. | Comply with the assembly procedure when tightening. Refer to Assembly. |
Disassembly
Remove the oil temperature sensor using the following procedure:Disconnect the harness connector from the oil temperature sensor connector and release clip.
Remove the oil temperature sensor and gasket from the transfer cover.Remove transfer cover mounting bolts (
).

Lightly tap transfer cover (1) with a plastic hammer to remove the transfer cover.

Remove O-ring from transfer cover.
Lightly tap the metal part of oil seals (1) with a punch from the back side of the transfer cover to remove oil seals.

Remove the ring gear bearing adjusting shim [transfer cover side (1)] and ring gear bearing outer race [transfer cover side (2)] using drift (commercial service tool).

Remove drain plug and gasket.
Remove filler plug and gasket.
Perform inspection after disassembly. Refer to Inspection.
Assembly
Select the ring gear bearing adjusting shim (transfer cover side). Refer to Adjustment.
Install the selected ring gear bearing adjusting shim [transfer cover side (1)] and ring gear bearing outer race [transfer cover side (2)] using drift (commercial service tool).

Install gasket onto drain plug and install them to transfer cover.
Install the transfer cover to the transfer case, and apply anti-corrosive oil onto the thread and seats on the mounting bolts. Then tighten mounting bolts to the specified torque.

Check the backlash, tooth contact, total preload and companion flange runout. Refer to Adjustment.
Remove transfer cover to install O-ring.
Apply multi-purpose grease lightly and evenly onto an O-ring, and install it to the transfer cover.
Install the transfer cover to the transfer case, and apply anti-corrosive oil onto thread and seats on the mounting bolts. Then tighten mounting bolts to the specified torque.

Using drift (commercial service tool), drive the transfer cover oil seal.
| Depth | : 0 +0.6/-0 mm (0 +0.024/-0 in) |
Using Tool, drive the transfer cover dust seal.
| Tool | : — (NI-53127) |

Install the oil temperature sensor using the following procedure:Attach the gasket to the oil temperature sensor and attach the main body to the transfer cover.
Install the oil temperature sensor clip and connect harness connector.Install gasket onto filler plug and install them to transfer cover.
Inspection
Inspection After Disassembly
Check items below. If necessary, replace them with new ones.
Transfer Cover
Check the bearing mounting surface for wear, cracks and damages.
Ring Gear Shaft Nissan Pathfinder 5th Gen
Exploded View

| 1. | Transfer cover dust seal | 2. | Transfer cover | 3. | Filler plug |
| 4. | Gasket | 5. | Transfer cover oil seal | 6. | O-ring |
| 7. | Ring gear bearing adjusting shim (transfer cover side) | 8. | Ring gear bearing (transfer cover side) | 9. | Gasket |
| 10. | Transfer oil temperature sensor | 11. | Ring gear shaft | 12. | Ring gear |
| 13. | Ring gear bearing (transfer case side) | 14. | Baffle plate | 15. | Snap ring |
| 16. | Ring gear bearing outer race (transfer case side) | 17. | Ring gear bearing adjusting shim (transfer case side) | 18. | Transfer case |
| 19. | Drain plug | 20. | Plug | 21. | O-ring |
| 22. | Oil seal | 23. | Dowel pin | 24. | Drive pinion |
| 25. | Drive pinion adjusting shim | 26. | O-ring | 27. | Pinion bearing assembly |
| 28. | Oil seal | 29. | Dust cover | 30. | Companion flange |
| 31. | Pinion lock nut | A. | Oil seal lip | B. | Comply with the assembly procedure when tightening. Refer to Assembly. |
Disassembly
Remove transfer cover assembly. Refer to Disassembly.
Remove ring gear bearing outer race (transfer cover side) and ring gear bearing adjusting shim (transfer cover side) from the transfer cover. Refer to Disassembly.
Remove ring gear shaft assembly from the transfer case.
Remove ring gear bearing outer race (transfer case side) and ring gear bearing adjusting shim (transfer case side) from the transfer case. Refer to Disassembly.
Remove ring gear bearing inner race (transfer cover side) from ring gear shaft with drift (A) (commercial service tool) and bearing separator (commercial service tool).

Remove ring gear bearing inner race (transfer case side) from ring gear shaft with drift [commercial service tool (A)] and bearing separator (commercial service tool).

Remove snap ring. Refer to Exploded View.
Remove ring gear bearing from ring gear shaft with drift [commercial service tool (A)] and separator (commercial service tool).

Perform inspection after disassembly. Refer to Inspection.
Assembly
Select ring gear bearing adjusting shim (transfer case side) and ring gear bearing adjusting shim (transfer cover side). Refer to Adjustment.
Assemble the selected ring gear bearing adjusting shim (transfer case side) and ring gear bearing outer race (transfer case side) to transfer case. Refer to Assembly.
Assemble the selected ring gear bearing adjusting shim (transfer cover side) and ring gear bearing outer race (transfer cover side) to transfer cover. Refer to Assembly.
Install the ring gear to ring gear shaft.
Install snap ring.
Install the ring gear bearing inner race (transfer cover side) with drift [commercial service tool(A)].

Install the ring gear bearing inner race (transfer case side) to ring gear shaft with drift [commercial service tool (A)].

Install the ring gear shaft assembly to the transfer case.
Apply multi-purpose grease to spline part indicated in the figure.

Install transfer cover to check and adjust each part. Refer to Assembly.
Check backlash, tooth contact, total preload and companion flange runout. Refer to Adjustment.
Reinstall transfer cover for installing O-ring. Refer to Assembly.
After installing transfer case oil seals, remove wrapped vinyl from the spline of ring gear shaft.
Inspection
inspection AFTER DISASSEMBLY
Check items below. If necessary, replace them with new ones.
Gear and Shaft
Check gear face and shaft for wear, cracks, damage, and seizure.
Bearing
Check for seizure, peeling, wear, corrosion, sticking, unusual noise, roughness in hand turning, and other damage.
Shim
Check for seizure, damage, and unusual wear.
Drive Pinion Nissan Pathfinder 5th Gen
Exploded View

| 1. | Transfer cover dust seal | 2. | Transfer cover | 3. | Filler plug |
| 4. | Gasket | 5. | Transfer cover oil seal | 6. | O-ring |
| 7. | Ring gear bearing adjusting shim (transfer cover side) | 8. | Ring gear bearing (transfer cover side) | 9. | Gasket |
| 10. | Transfer oil temperature sensor | 11. | Ring gear shaft | 12. | Ring gear |
| 13. | Ring gear bearing (transfer case side) | 14. | Baffle plate | 15. | Snap ring |
| 16. | Ring gear bearing outer race (transfer case side) | 17. | Ring gear bearing adjusting shim (transfer case side) | 18. | Transfer case |
| 19. | Drain plug | 20. | Plug | 21. | O-ring |
| 22. | Oil seal | 23. | Dowel pin | 24. | Drive pinion |
| 25. | Drive pinion adjusting shim | 26. | O-ring | 27. | Pinion bearing assembly |
| 28. | Oil seal | 29. | Dust cover | 30. | Companion flange |
| 31. | Pinion lock nut | A. | Oil seal lip | B. | Comply with the assembly procedure when tightening. Refer to Assembly. |
Disassembly
Remove pinion bearing assembly bolts.

Lightly tap companion flange with a plastic hammer to remove drive pinion assembly (1).

Remove the O-ring from the pinion bearing.
Remove the pinion lock nut.
Remove drive pinion from pinion bearing assembly with drift [commercial service tool (A) and bearing separator [commercial service tool (B)].

Remove the adjusting shim.
Remove the companion flange.
Remove the dust cover.
Remove the oil seal.
Perform inspection after disassembly. Refer to Inspection.
Assembly
Select drive pinion adjusting shim. Refer to Adjustment.
Assemble the selected drive pinion adjusting shim to drive pinion.
Install the drive pinion to pinion bearing assembly with drift (commercial service tool).
Install oil seal to pinion bearing assembly with drift (A) (commercial service tool).

Install dust cover.
Install companion flange (1) to pinion bearing with drift (A) (commercial service tool).

Apply anti-corrosive oil to the thread and seat of the lock nut, and adjust the pinion lock nut tightening torque and pinion bearing preload torque, using a preload gauge.Install pinion lock nut, and then tighten to the specified torque.
| Pinion lock nut tightening torque | : 90±9 N·m |
| Pinion bearing preload | : Refer to Preload Torque. |
Apply multi-purpose grease lightly and evenly onto an O-ring, and install it to the pinion bearing assembly.
Install drive pinion assembly, and apply anti-corrosive oil onto thread and seats on the mounting bolts. Tighten to the specified torque.

Check backlash, tooth contact, total preload and companion flange runout. Refer to Adjustment.
Adjustment
ADJUSTING SHIM SELECTION

Select adjusting shim of T1, T2, and T3, respectively, by using the following equation.
T1 [Ring gear bearing adjusting shim (transfer case side)]
T1 = A −(B +X/2) +C +W −V −F −(M/100) +0.055 mm (0.0022 in)
T2 [Ring gear bearing adjusting shim (transfer cover side)]
T2 = −Y +Z +(B +X/2) −C −W −H +(M/100) +0.055 mm (0.0022 in)
T3 (Drive pinion adjusting shim)
T3 = −Q +(R +S/2) −K +(O/100)
Check dimension (M) on the ring gear side face.

Check dimension (O) on the gear end of the drive pinion.

PINION BEARING PRELOAD
Remove ring gear shaft assembly from the transfer case. Refer to Disassembly.
Rotate the companion flange back and forth from 2 to 3 times to check for unusual noise, binding, sticking, and so on.
Rotate the companion flange at least 20 times to check for smooth operation of the bearing.
Measure the pinion bearing preload with the preload gauge (A) [SST: ST3127S000 (NI-25765-A)].

| Pinion bearing preload | : Refer to Preload Torque. |
If outside the standard, disassemble the drive pinion assembly to check and adjust each part.
TOTAL PRELOAD
Measure pinion bearing preload.
Assemble the ring gear shaft assembly to the transfer case. Refer to Assembly.
Install transfer cover to check and adjust each part. Refer to Assembly.
Rotate the companion flange at least 20 times to check for smooth operation of the bearing.
Measure the total preload with the preload gauge (A) [SST: ST3127S000 (NI-25765-A)].

| Total preload | : Refer to Preload Torque. |
If outside the standard, disassemble the transfer assembly to check and adjust each part. Measure it with the transfer case oil seal and transfer cover oil seal removed when measuring total preload after disassembly. Then install transfer case oil seals and transfer cover oil seal.
BACKLASH
Install the bolt to the companion flange.
Fit a dial indicator onto the bolt (A).

Measure the circumference backlash of the companion flange.
| Backlash | : Refer to Backlash. |
If outside the standard, disassemble the transfer assembly to check and adjust each part.
TOOTH CONTACT
Remove transfer cover. Refer to Disassembly.
Remove ring gear shaft assembly from transfer case. Refer to Disassembly.
Apply red lead onto the ring gear.

Assemble the ring gear shaft assembly to the transfer case. Refer to Assembly.
Install transfer cover to check and adjust each part. Refer to Assembly.
Remove the plug from the transfer case.
Rotate the companion flange back and forth several times, and check the drive pinion gear to ring gear tooth contact by viewing from the plug hole.
Tooth Contact Judgment Guide 
Follow the procedure below to adjust pinion height (dimension X) if tooth contact is improper. For selecting adjusting shim, refer to the latest parts information.

Thicken the drive pinion adjusting shim to move the drive pinion closer to the ring gear in case of face contact or heel contact.

Thin the drive pinion adjusting shim to move the drive pinion farther from the ring gear in case of flank contact or toe contact.

COMPANION FLANGE RUNOUT
Fit a dial indicator onto the companion flange face (inner side of the propeller shaft mounting bolt holes).

Rotate the companion flange to check for runout.
| Companion flange runout | : Refer to Companion Flange Runout. |
Fit a test indicator to the inner side of the companion flange (socket diameter).
Rotate the companion flange to check for runout.
| Companion flange runout | : Refer to Companion Flange Runout. |
Follow the procedure below to adjust if runout value is outside the repair limit.Check for runout while changing the phase between companion flange and drive pinion in 90° steps. Then search for the minimum point. Replace companion flange if runout value is still outside the limit after the phase has been changed. Adjust assembly status of the pinion bearing and drive pinion, or replace pinion bearing assembly if runout is outside the standard after the companion flange is replaced.
Inspection
INSPECTION AFTER DISASSEMBLY
Check items below. If necessary, replace them with new ones.
Gear and Shaft
Check gear face and shaft for wear, cracks, damage, and seizure.
Bearing
Check for seizure, peeling, wear, corrosion, sticking, unusual noise, roughness in hand turning, and other damage.
Shim
Check for seizure, damage, and unusual wear.
Transfer Case Nissan Pathfinder 5th Gen
Exploded View

| 1. | Transfer cover dust seal | 2. | Transfer cover | 3. | Filler plug |
| 4. | Gasket | 5. | Transfer cover oil seal | 6. | O-ring |
| 7. | Ring gear bearing adjusting shim (transfer cover side) | 8. | Ring gear bearing (transfer cover side) | 9. | Gasket |
| 10. | Transfer oil temperature sensor | 11. | Ring gear shaft | 12. | Ring gear |
| 13. | Ring gear bearing (transfer case side) | 14. | Baffle plate | 15. | Snap ring |
| 16. | Ring gear bearing outer race (transfer case side) | 17. | Ring gear bearing adjusting shim (transfer case side) | 18. | Transfer case |
| 19. | Drain plug | 20. | Plug | 21. | O-ring |
| 22. | Oil seal | 23. | Dowel pin | 24. | Drive pinion |
| 25. | Drive pinion adjusting shim | 26. | O-ring | 27. | Pinion bearing assembly |
| 28. | Oil seal | 29. | Dust cover | 30. | Companion flange |
| 31. | Pinion lock nut | A. | Oil seal lip | B. | Comply with the assembly procedure when tightening. Refer to Assembly. |
Disassembly
Remove transfer cover. Refer to Disassembly.
Remove ring gear shaft assembly. Refer to Disassembly.
Remove drive pinion assembly. Refer to Disassembly.
Remove O-ring from transfer case.
Remove bolts (A) and baffle plate (1).

Remove the ring gear bearing adjusting shim (transfer case side) (1) and ring gear bearing outer race (transfer case side) (2) by tapping from the 2 cutouts (
) on the transfer case.

Remove plug and gasket.
Perform inspection after disassembly. Refer to Inspection.
Assembly
Select the ring gear bearing adjusting shim (transfer case side). Refer to Adjustment.
Install the selected ring gear bearing adjusting shim (transfer case side) and the ring gear bearing outer race (transfer case side) using drift (A) (commercial service tool).

Install drive pinion assembly. Refer to Assembly.
Install baffle plate (1) and bolts (A).

Install ring gear shaft assembly. Refer to Assembly.
Install transfer cover to check and adjust each part. Refer to Assembly.
Check backlash, tooth contact, total preload and companion flange runout. Refer to Adjustment.
Reinstall transfer cover for installing O-ring. Refer to Assembly.
Install oil seals with drift (commercial service tool).

| A | : 67.5 ± 0.5 mm (2.657 ± 0.020 in) |
After installing oil seals to transfer case, remove wrapped vinyl from the spline of ring gear shaft.
Apply multi-purpose grease lightly and evenly onto an O-ring, and install it to the transfer case.
Inspection
Inspection After Disassembly
Check items below. If necessary, replace them with new ones.
Case
Check the bearing mounting surface for wear, cracks and damages.