Lan System - Dtc/circuit Diagnosis
- B2600-42 Config Error
- B2600-56 Config Error
- U2340-87 Can Comm Circuit
- U278c-88 Ethernet Port1 Failure
- Power Supply and Ground Circuit
B2600-42 Config Error Nissan Pathfinder 5th Gen
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms (Trouble diagnosis content) | DTC detected condition | |
|---|---|---|---|
| B2600-42 | CONFIG ERROR (Configuration error) |
Diagnosis condition | When ignition switch is ON. |
| Signal (terminal) | — | ||
| Threshold | Errors are detected in the data stored in the 8CH CAN gateway (except programming data) | ||
| Diagnosis delay time | 2 seconds or more | ||
POSSIBLE CAUSE
8CH CAN gateway
FAIL-SAFE
8CH CAN gateway stops transmitting and receiving the following.
CAN communication signals between each CAN communication circuit
Ethernet communication signals between each ethernet communication circuit
Confirmation Procedure
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
Turn ignition switch ON and wait at least 2 seconds or more.
Select “Self Diagnostic Result” mode of “8ch CAN GATEWAY 2” using CONSULT.
Check DTC.
Is DTC B2600-42 detected?
YES>>Refer to DTC Diagnosis Procedure.
NO-1>>To check malfunction symptom before repair: Intermittent Incident
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
PERFORM DTC CONFIRMATION PROCEDURE AGAIN
Turn ignition switch ON.
Erase DTC.
Perform DTC confirmation procedure again. Refer to Confirmation Procedure.
Check DTC.
Is DTC B2600-42 displayed?
YES>>Replace 8CH CAN gateway. Refer to Removal and Installation.
NO>>INSPECTION END
B2600-56 Config Error Nissan Pathfinder Fifth generation
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms (Trouble diagnosis content) | DTC detected condition | |
|---|---|---|---|
| B2600-56 | CONFIG ERROR (Configuration error) |
Diagnosis condition | When ignition switch is ON. |
| Signal (terminal) | — | ||
| Threshold | Monitoring mode is set. | ||
| Diagnosis delay time | 2 seconds or more | ||
POSSIBLE CAUSE
8CH CAN gateway
FAIL-SAFE
—
Confirmation Procedure
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
Turn ignition switch ON and wait at least 2 seconds or more.
Select “Self Diagnostic Result” mode of “8ch CAN GATEWAY 2” using CONSULT.
Check DTC.
Is DTC B2600-56 detected?
YES>>Refer to DTC Diagnosis Procedure.
NO-1>>To check malfunction symptom before repair: Intermittent Incident
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
REMOVE AND INSTALL BATTERY
Turn ignition switch OFF.
Disconnect the battery cable from the negative terminal.
Connect the battery cable to the negative terminal.
GO TO 2.
PERFORM DTC CONFIRMATION PROCEDURE AGAIN
Turn ignition switch ON.
Perform DTC confirmation procedure again. Refer to Confirmation Procedure.
Check DTC.
Is DTC B2600-56 displayed?
YES>>Replace 8CH CAN gateway. Refer to Removal and Installation.
NO>>INSPECTION END
U2340-87 Can Comm Circuit Nissan Pathfinder SUV
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms (Trouble diagnosis content) | DTC detected condition | |
|---|---|---|---|
| U2340-87 | CAN COMM CIRCUIT (CAN communication circuit) |
Diagnosis condition | When ignition switch is ON. |
| Signal (terminal) | CAN communication signal | ||
| Threshold | Lost communication with ECM | ||
| Diagnosis delay time | 4 seconds or more | ||
POSSIBLE CAUSE
Harness or connector
(CAN communication line)
8CH CAN gateway
ECM malfunction
FAIL-SAFE
System continue normal control.
Confirmation Procedure
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
Turn ignition switch ON and wait at least 4 seconds or more.
Select “Self Diagnostic Result” mode of “8ch CAN GATEWAY 2” using CONSULT.
Check DTC.
Is DTC U2340-87 detected?
YES>>Refer to DTC Diagnosis Procedure.
NO-1>>To check malfunction symptom before repair: Intermittent Incident
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
PERFORM DTC CONFIRMATION PROCEDURE AGAIN
Turn ignition switch ON.
Erase DTC.
Perform DTC confirmation procedure again. Refer to Confirmation Procedure.
Check DTC.
Is DTC “U2340-87” detected?
YES>>Perform trouble diagnosis procedure for CAN communication system. Refer to Trouble Diagnosis Flow Chart.
NO>>INSPECTION END
U278c-88 Ethernet Port1 Failure Nissan Pathfinder 2022
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms (Trouble diagnosis content) | DTC detected condition | |
|---|---|---|---|
| U278C-88 | ETHERNET PORT1 FAILURE (Ethernet port1 failure) |
Diagnosis condition | When ignition switch is ON. |
| Signal (terminal) | — | ||
| Threshold | Lost ethernet communication with AV control unit | ||
| Diagnosis delay time | 7 seconds or more | ||
POSSIBLE CAUSE
Ethernet harness
8CH CAN gateway
AV control unit
FAIL-SAFE
8CH CAN gateway stops transmitting and receiving ethernet communication signals between ethernet communication circuit which cannot communicate.
Confirmation Procedure
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT
Turn ignition switch ON and wait at least 3 minutes or more.
Select “Self Diagnostic Result” mode of “8ch CAN GATEWAY 2” using CONSULT.
Check DTC.
Is DTC U278C–88 detected?
YES>>Refer to DTC Diagnosis Procedure.
NO-1>>To check malfunction symptom before repair: Intermittent Incident
NO-2>>Confirmation after repair: INSPECTION END
DTC Diagnosis Procedure
CHECK CONNECTOR
Ignition switch OFF.
Check the ethernet harness connectors and terminals of 8CH CAN gateway and AV control unit for damage or looseness.
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace the malfunction part, securely lock the harness connector.
PERFORM ALL DTC READING
Ignition switch ON.
Perform “All DTC Reading” with CONSULT.
Check if any DTCs of ethernet (DTC “U2754-88”) are detected in “Self Diagnostic Result” of “MULTI AV”
Are any DTCs of ethernet detected?
YES>>Replace the 8CH CAN gateway (Refer to Removal and Installation), and GO TO 3.
NO>>Replace the AV control unit. Refer to Removal and Installation.
PERFORM DTC CONFIRMATION PROCEDURE-1
Erases all self-diagnosis results with CONSULT.
Perform DTC confirmation procedure again. Refer to Confirmation Procedure.
Is DTC “U278C-88” detected as the current malfunction?
YES>>Replace the AV control unit (Refer to Removal and Installation), and GO TO 4.
NO>>INSPECTION END
PERFORM DTC CONFIRMATION PROCEDURE-2
Erases all self-diagnosis results with CONSULT.
Perform DTC confirmation procedure again. Refer to Confirmation Procedure.
Is DTC “U278C-88” detected as the current malfunction?
YES>>Replace the ethernet harness between 8CH CAN gateway and AV control unit.
NO>>INSPECTION END
Power Supply and Ground Circuit Nissan Pathfinder R53
8ch Can Gateway
Diagnosis Procedure
CHECK FUSE
Check that the following fuse are not blown.
| Signal name | Fuse No. |
|---|---|
| Battery power supply | 16 |
| Ignition power supply | 9 |
| Accessory power supply | 40 |
Is the fuse blown (open)?
YES>>Replace the blown fuse after repairing the affected circuit if a fuse is blown.
NO>>GO TO 2.
CHECK POWER SUPPLY CIRCUIT
Turn the ignition switch OFF.
Disconnect the connector of 8CH CAN gateway.
Check voltage between 8CH CAN gateway harness connector and ground.
Terminals Condition Voltage
(Standard)Voltage
(Reference value)(+) (−) 8CH CAN gateway Ground Ignition switch Connector Terminal M5 1 OFF 6 – 16 V Battery
voltage17 ON 7 – 16 V Battery
voltage18 ACC 7 – 16 V Battery
voltage
Is the measurement value normal?
YES>>GO TO 3.
NO>>Repair harness or connector.
CHECK GROUND CIRCUIT
Check continuity between 8CH CAN gateway harness connector and ground.
| 8CH CAN gateway | Ground | Continuity | |
| Connector | Terminal | ||
| M5 | 21 | Existed | |
| 28 | |||
Does continuity exist?
YES>>INSPECTION END
NO>>Repair harness or connector.