Automatic Drive Positioner - Dtc/circuit Diagnosis

In this manual: Automatic Drive Positioner - Dtc/circuit Diagnosis
General Information — 8Engine :: Engine Mechanical — 19Engine Lubrication System - Precautions. Preparation — 1Engine Lubrication System - Lubrication System (System Description). Engine Oil Pressure (Basic Inspection). Service Data and Specifications (SDS) — 1Engine Cooling System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Engine Cooling System - Engine Coolant — 1Engine Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Engine Control System - Ecu Diagnosis Information — 1Ecu Diagnosis Information - Ecm ++ — 1Engine Control System - Basic Inspection — 1Basic Inspection - Diagnosis and Repair Workflow ++ — 1Basic Inspection - Basic Inspection ++ — 1Basic Inspection - Additional Service When Replacing Ecm ++ — 1Basic Inspection - Fuel Pressure Check ++ — 1Basic Inspection - How to Set Srt Code ++ — 1Basic Inspection - How to Erase Permanent Dtc ++ — 1Engine Control System - Dtc/circuit Diagnosis — 1Engine Control System - Symptom Diagnosis — 1Engine Control System - Periodic Maintenance — 1Engine Control System - Removal and Installation — 1Fuel System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Fuel System - Fuel System (Periodic Maintenance). Fuel Level Sensor Unit (Disassembly and Assembly) — 1Exhaust System - Precautions. Preparation — 1Exhaust System - Exhaust System (Periodic Maintenance). Exhaust System (Removal and Installation) — 1Starting System - Precautions. Preparation. Starter Motor (Service Data and Specifications (sds)) — 1Starting System - Diagnosis and Repair Work Flow — 1Starting System - Starting System (Symptom Diagnosis). Starter Motor (Removal and Installation) — 1Accelerator Control System - Precautions. Service Data and Specifications (SDS) — 1Accelerator Control System - Accelerator Pedal Assembly — 1Transmission & Driveline :: Transaxle & Transmission — 21Driveline - System Description — 1Transfer: Ty92b - Ecu Diagnosis Information. Awd Control Unit ++ — 1Driveline - Basic Inspection — 1Driveline - Dtc/circuit Diagnosis — 1Driveline - Symptom Diagnosis — 1Driveline - Removal and Installation — 1Transfer: Ty92b - Unit Removal and Installation. Transfer Assembly ++ — 1Driveline - Unit Disassembly and Assembly — 1Driveline - Basic Inspection — 1Driveline - Removal and Installation — 1Driveline - Unit Disassembly and Assembly — 1Front Axle - Precautions. Preparation — 1Front Axle - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Front Axle - Front Drive Shaft Boot — 1Front Axle - Front Drive Shaft — 1Rear Axle - Precautions. Preparation. Service Data and Specifications (SDS) — 1Rear Axle - Noise, Vibration and Harshness (nvh) Troubleshooting — 1Rear Axle - Rear Drive Shaft — 1Suspension :: Front Suspension — 7Rear Suspension - Precautions. Preparation — 1Rear Suspension - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Rear Suspension - Rear Suspension Assembly — 1Road Wheels & Tires - Precautions — 1Road Wheels & Tires - Preparation. Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Road Wheels & Tires - System — 1Brakes :: Brake System — 9Parking Brake System - Precautions. Preparation — 1Parking Brake System - System — 1Vdc/tcs/abs - Precautions ++ — 1Brake Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Dtc/circuit Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Steering :: Steering System — 9Steering Control System - Precautions — 1Steering Control System - System — 1Steering Control System - Eps Control Unit (Ecu Diagnosis Information. Removal and Installation) — 1Restraints :: Seat Belt — 7Srs Air Bag - Precautions. Preparation — 1Srs Air Bag - Collision Diagnosis — 1Srs Air Bag - Occupant Classification System — 1Srs Air Bag Control System - Precautions — 1Srs Air Bag Control System - System — 1Srs Air Bag Control System - Diagnosis Sensor Unit — 1Srs Air Bag Control System - Inspection and Adjustment — 1Ventilation, Heater & Air Conditioner :: Ventilation System — 6Heater & Air Conditioning System - Precautions — 1Heater & Air Conditioning System - Preparation — 1Heater & Air Conditioning System - Component Parts — 1Heater & Air Conditioning System - Diagnosis and Repair Work Flow — 1Heater & Air Conditioning System - Compressor — 1Heater & Air Conditioning System - Cooler Pipe and Hose — 1Heater & Air Conditioning System - Condenser. Condenser — 1Heater & Air Conditioning System - Heating and Cooling Unit Assembly — 1Heater & Air Conditioning System - Service Data and Specifications (SDS) — 1Heater & Air Conditioning Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1Heater & Air Conditioning Control System - Ecu Diagnosis Information — 1Heater & Air Conditioning Control System - Basic Inspection — 1Heater & Air Conditioning Control System - Dtc/circuit Diagnosis — 1Heater & Air Conditioning Control System - Symptom Diagnosis — 1Heater & Air Conditioning Control System - Removal and Installation — 1Body Interior :: Interior — 8Instrument Panel - Precautions. Preparation. Clip List — 1Instrument Panel - Squeak and Rattle Trouble Diagnoses — 1Instrument Panel - Cluster Lid C — 1Seat - Precautions — 1Seat - Preparation. Clip List — 1Seat - Component Parts — 1Seat - System — 1Seat - Diagnosis and Repair Work Flow — 1Seat - Front Seat — 1Seat - Second Row Seats — 1Seat - Third Row Seats — 1Seat - Front Seat — 1Seat - Second Row Seat — 1Seat - Third Row Seat — 1Automatic Drive Positioner - Precautions. Preparation — 1Automatic Drive Positioner - System — 1Automatic Drive Positioner - Diagnosis and Repair Work Flow — 1Automatic Drive Positioner - Inspection and Adjustment — 1Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock — 38Security Control System - Precautions — 1Security Control System - System — 1Security Control System - Ecm, Bcm, Intelligent Key Unit, Ipdm E/r — 1Security Control System - Vehicle Security System Cannot Be Set — 1Glass & Window System - Precautions. Preparation — 1Glass & Window System - Squeak and Rattle Trouble Diagnoses — 1Power Window Control System - Precautions. Preparation — 1Power Window Control System - Power Supply and Ground Circuit — 1Power Window Control System - Power Window Motor Circuit — 1Power Window Control System - Front Power Window Rh Alone Does Not Operate — 1Power Window Control System - Rear Lh Side Power Window Alone Does Not Operate — 1Power Window Control System - Rear Rh Side Power Window Alone Does Not Operate — 1Roof - Precautions. Preparation — 1Roof - Power Supply and Ground Circuit — 1Roof - Moonroof Switch Assembly — 1Roof - Lin Communication Circuit — 1Roof - Auto Operation Does Not Operate — 1Roof - Anti-Pinch Function Does Not Operate — 1Exterior - Precautions. Preparation. Clip List (Preparation) — 1Exterior - Squeak and Rattle Trouble Diagnoses — 1Exterior - Fender Protector — 1Exterior - Over Fender — 1Exterior - Under Cover — 1Exterior - Roof Side Rail — 1Body Repair - Service Information — 1Service Information - Sheet Metal Work ++ — 1Service Information - Body Welding and Precautions ++ — 1Service Information - Safety and Health ++ — 1Service Information - Repairing Procedures and Precautions ++ — 1Body Repair - Precaution — 1Body Repair - Preparation — 1Body Repair - Removal and Installation — 1Driver Controls :: Mirrors — 8Exterior Lighting System - System Description — 1System Description - Component Parts ++ — 1Exterior Lighting System - Basic Inspection — 1Exterior Lighting System - Dtc/circuit Diagnosis — 1Exterior Lighting System - Symptom Diagnosis — 1Exterior Lighting System - Periodic Maintenance — 1Exterior Lighting System - Removal and Installation — 1Interior Lighting System - Precautions. Preparation — 1Interior Lighting System - Component Parts. Interior Lighting System — 1Interior Lighting System - System — 1Interior Lighting System - Diagnosis and Repair Work Flow — 1Interior Lighting System - Interior Lighting System Symptoms (Symptom Diagnosis). Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Interior Lighting System - Foot Lamp — 1Wiper & Washer - Precautions — 1Wiper & Washer - Preparation. Bcm, Ipdm E/r (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Wiper & Washer - System — 1Wiper & Washer - Diagnosis and Repair Work Flow — 1Defogger - Precautions. Bcm, A/c Auto Amp. (Ecu Diagnosis Information) — 1Defogger - Diagnosis and Repair Work Flow — 1Horn - Precautions — 1Electrical & Power Control :: Power Outlet — 13Body Control System - Precautions. Preparation — 1Body Control System - Component Parts — 1Body Control System - System — 1Body Control System - Diagnosis System (bcm) — 1Body Control System - Bcm — 1Lan System - System Description — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - Removal and Installation — 1Charging System - Precautions. Preparation. Ecm, Ipdm E/r (Ecu Diagnosis Information) — 1Charging System - Diagnosis and Repair Work Flow — 1Charging System - Charging System (Symptom Diagnosis). Generator (Removal and Installation). Service Data and Specifications (SDS) — 1Power Supply, Ground & Circuit Elements - Precautions. Preparation. Service Data and Specifications (SDS) — 1Driver Information & Multimedia :: Meter, Warning Lamp & Indicator — 25Warning Chime System - Application Notice (How to Use This Manual). Precautions — 1Warning Chime System - System — 1Warning Chime System - Diagnosis System (combination Meter) — 1Warning Chime System - Bcm, Combination Meter (Ecu Diagnosis Information). Diagnosis and Repair Work Flow (Basic Inspection) — 1Sonar System - Precautions. Preparation — 1Sonar System - Sonar Control Unit — 1Dtc/circuit Diagnosis - B2720 Corner Sensor [rl] ++ — 1Audio, Visual & Navigation System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Multi Av (av Control Unit) ++ — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Symptom Diagnosis - Multi Av System ++ — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Cruise Control & Driver Assistance :: Cruise Control System — 17Driver Assistance System - System Description — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Driver Assistance System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1System Description - Handling Precaution ++ — 1Driver Assistance System - Ecu Diagnosis Information — 1Driver Assistance System - Basic Inspection — 1Basic Inspection - Distance Sensor Alignment ++ — 1Basic Inspection - Camera Aiming Adjustment ++ — 1Basic Inspection - Action Test ++ — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Laser/radar (distance Sensor) ++ — 1Dtc/circuit Diagnosis - Lane Camera (front Camera Unit) ++ — 1Driver Assistance System - Symptom Diagnosis — 1Driver Assistance System - Removal and Installation — 1Driver Assistance System - System Description — 1System Description - System ++ — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Drive Mode System - Precautions — 1Drive Mode System - Component Parts. Drive Mode System — 1Drive Mode System - System — 1Drive Mode System - Diagnosis and Repair Work Flow — 1Drive Mode System - Drive Mode Select Switch Circuit — 1Maintenance - Precautions. Preparation — 1Maintenance - General Maintenance — 1Maintenance - Periodic Maintenance — 1Maintenance - Recommended Fluids and Lubricants — 1Maintenance - Engine Maintenance — 1Maintenance - Chassis and Body Maintenance — 1Engine Lubrication System - Periodic Maintenance — 1Engine Lubrication System - Removal and Installation — 1Engine Cooling System - System Description — 1Engine Cooling System - Removal and Installation — 1Engine Control System - Vq35dd — 1Fuel System - Removal and Installation — 1Starting System - System Description — 1Starting System - Dtc/circuit Diagnosis — 1Driveline - Transfer: Ty92b — 1Driveline - Rear Propeller Shaft: 3fcj-Cvj — 1Driveline - Rear Final Drive: R145 — 1Front Axle - Periodic Maintenance — 1Front Axle - Removal and Installation — 1Rear Axle - Periodic Maintenance — 1Rear Axle - Removal and Installation — 1Rear Suspension - Removal and Installation — 1Road Wheels & Tires - System Description — 1Road Wheels & Tires - Basic Inspection — 1Road Wheels & Tires - Dtc/circuit Diagnosis — 1Road Wheels & Tires - Symptom Diagnosis — 1Road Wheels & Tires - Periodic Maintenance — 1Road Wheels & Tires - Removal and Installation — 1Parking Brake System - System Description — 1Parking Brake System - Basic Inspection — 1Parking Brake System - Dtc/circuit Diagnosis — 1Parking Brake System - Symptom Diagnosis — 1Parking Brake System - Removal and Installation — 1Brake Control System - Vdc/tcs/abs — 1Brake Control System - Automatic Brake Hold — 1Brake Control System - Automatic Emergency Braking — 1Brake Control System - Rear Automatic Braking — 1Steering Control System - System Description — 1Steering Control System - Basic Inspection — 1Steering Control System - Dtc/circuit Diagnosis — 1Steering Control System - Symptom Diagnosis — 1Srs Air Bag - Removal and Installation — 1Srs Air Bag Control System - System Description — 1Srs Air Bag Control System - Basic Inspection — 1Srs Air Bag Control System - Symptom Diagnosis — 1Heater & Air Conditioning System - Symptom Diagnosis — 1Heater & Air Conditioning System - Periodic Maintenance — 1Heater & Air Conditioning Control System - Automatic Air Conditioning — 1Instrument Panel - Removal and Installation — 1Instrument Panel - Unit Disassembly and Assembly — 1Seat - Ecu Diagnosis Information — 1Seat - Dtc/circuit Diagnosis — 1Seat - Symptom Diagnosis — 1Automatic Drive Positioner - System Description — 1Automatic Drive Positioner - Ecu Diagnosis Information — 1Automatic Drive Positioner - Dtc/circuit Diagnosis — 1Automatic Drive Positioner - Symptom Diagnosis — 1Automatic Drive Positioner - Removal and Installation — 1Security Control System - System Description — 1Security Control System - Basic Inspection — 1Security Control System - Dtc/circuit Diagnosis — 1Security Control System - Symptom Diagnosis — 1Security Control System - Removal and Installation — 1Glass & Window System - Removal and Installation — 1Power Window Control System - System Description — 1Power Window Control System - Ecu Diagnosis Information — 1Power Window Control System - Basic Inspection — 1Power Window Control System - Dtc/circuit Diagnosis — 1Power Window Control System - Symptom Diagnosis — 1Power Window Control System - Removal and Installation — 1Roof - System Description — 1Roof - Ecu Diagnosis Information — 1Roof - Basic Inspection — 1Roof - Dtc/circuit Diagnosis — 1Roof - Symptom Diagnosis — 1Roof - Removal and Installation — 1Exterior - System Description — 1Exterior - Removal and Installation — 1Body Repair - Repair Information — 1Exterior Lighting System - Led Headlamp — 1Interior Lighting System - Dtc/circuit Diagnosis — 1Interior Lighting System - Removal and Installation — 1Wiper & Washer - System Description — 1Wiper & Washer - Dtc/circuit Diagnosis — 1Wiper & Washer - Symptom Diagnosis — 1Wiper & Washer - Removal and Installation — 1Defogger - System Description — 1Defogger - Dtc/circuit Diagnosis — 1Defogger - Symptom Diagnosis — 1Defogger - Removal and Installation — 1Horn - Removal and Installation — 1Body Control System - Basic Inspection — 1Body Control System - Dtc/circuit Diagnosis — 1Body Control System - Symptom Diagnosis — 1Body Control System - Removal and Installation — 1Lan System - Can Fundamental — 1Lan System - Can — 1Lan System - Can Gateway — 1Power Control System - Ipdm E/r — 1Power Control System - Power Distribution System — 1Charging System - System Description — 1Charging System - Dtc/circuit Diagnosis — 1Power Supply, Ground & Circuit Elements - System Description — 1Power Supply, Ground & Circuit Elements - Basic Inspection — 1Power Supply, Ground & Circuit Elements - Removal and Installation — 1Warning Chime System - System Description — 1Warning Chime System - Dtc/circuit Diagnosis — 1Warning Chime System - Symptom Diagnosis — 1Sonar System - System Description — 1Sonar System - Basic Inspection — 1Sonar System - Dtc/circuit Diagnosis — 1Sonar System - Symptom Diagnosis — 1Sonar System - Removal and Installation — 1Audio, Visual & Navigation System - Nissanconnect — 1Audio, Visual & Navigation System - Intelligent Around View Monitor System — 1Audio, Visual & Navigation System - Rear View Monitor System — 1Audio, Visual & Navigation System - Telematics System — 1Driver Assistance System - Adas Control Unit 2 — 1Driver Assistance System - Driver Assistance System — 1Driver Assistance System - Chassis Control — 1Drive Mode System - Removal and Installation — 1Dtc/circuit Diagnosis (C053c Wheel Speed Sensor ... U2141 Can Comm Circuit) — 1Dtc/circuit Diagnosis (P0011 Intake Valve Timing Control ... P0111 Iat Sensor) — 1Dtc/circuit Diagnosis (P0116 Engine Coolant Temperature Sensor ... P025b Fuel Pump Module a) — 1Dtc/circuit Diagnosis (P026b Injection Timing ... P0420 Three Way Catalyst Function) — 1Dtc/circuit Diagnosis (P0441 Evap Control System ... P0524 Engine Oil Pressure) — 1Dtc/circuit Diagnosis (P0532 A/c Refrigerant Pressure Sensor ... P064d Ecm) — 1Dtc/circuit Diagnosis (P06da Engine Oil Pressure Control Solenoid Valve ... P1217 Engine Over Temperature) — 1Dtc/circuit Diagnosis (P1220 Fuel Pump Control Module (fpcm) ... P1574 Ascd Vehicle Speed Sensor) — 1Dtc/circuit Diagnosis (P1575 Brake Switch ... P2101 Electric Throttle Control Function) — 1Dtc/circuit Diagnosis (P2118 Throttle Control Motor ... P34ac Electric Intake Valve Timing Control Actuator) — 1Dtc/circuit Diagnosis (Active Grille Shutter ... High Pressure Fuel Pump) — 1Dtc/circuit Diagnosis (Ignition Signal ... Variable Induction Air System) — 14012 C1040 Emergency Brake — 14013 C106a Wheel Sensor — 14014 C1078-55 Not Configuration — 14015 C10b4-98 Overheat — 14016 B1001 Lap Pre-Tensioner Lh — 14017 B0001 Driver Air Bag Module — 14018 B100e Knee Air Bag Module Rh — 14019 B142x Collision Detection — 1Dtc/circuit Diagnosis (B20c7-11 A/c Clutch ... B24a6-11 in-Vehicle Sensor) — 1Dtc/circuit Diagnosis (B24a6-15 in-Vehicle Sensor ... U2140-87 Can Comm Err (ecm)) — 1Dtc/circuit Diagnosis (C1f00-1c Control Unit ... C1f04-61 Brake Sw/stop Lamp Sw) — 1Dtc/circuit Diagnosis (C1f05-49 Front Camera Unit ... C1f70-87 Ethernet Circuit) — 1
115steps
~690min
4/5difficulty
Done 0 of 115
  • B2900-01 Sliding / Lifting Switch
  • B2920-09 Driver Seat Control Unit
  • B2921-A2 Driver Seat Control Unit
  • B2921-A3 Driver Seat Control Unit
  • U2118-87 Can Comm Err (intelligent Key)
  • Power Supply and Ground Circuit (driver Seat Control Unit)
  • Sliding Switch
  • Seat Memory Switch
  • Power Seat Switch Lh Ground Circuit
  • Sliding Sensor
  • Tilt Sensor
  • Sliding Motor
  • Lifting Motor (front)
  • Telescopic Motor
  • Seat Memeory Switch Indicator

B2900-01 Sliding / Lifting Switch Nissan Pathfinder 5th Gen

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC detection condition
B2900-01

Sliding / lifting switch

(Sliding / lifting switch)
Diagnosis condition The power consumption control of driver seat control unit is in wake-up state
Signal (terminal) Sliding / lifting switch signal (terminal #31)
Threshold 0.352 – 3.962 V
Diagnosis delay time 20 seconds or more

POSSIBLE CAUSE

  • Sliding / lifting switch

  • Driver seat control unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 20 seconds or more.

  2. Select “Self Diagnostic Result” mode of “AUTO DRIVE POS.”.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK SLIDING / LIFTING SWITCH SIGNAL VOLTAGE

Check voltage between driver seat control unit harness connector and ground.

(+)(—)Condition

Voltage

(Approx.)
Driver seat control unit
ConnectorTerminal
B209 31 Ground Sliding switch Operate (forward) 3.065 – 3.962 V
Operate (backward) 2.638 – 3.064 V
Lifting switch Operate (upward) 0.789 – 1.755 V
Operate (downward) 0.352 – 0.788 V
Sliding / lifting switch release 3.963 – 4.799 V*

*: When the power consumption control of driver seat control unit is in wake-up state.

Is the inspection result normal?

YES>>

Inspection End.

NO>>

GO TO 2.

CHECK SLIDING / LIFTING SWITCH

Check sliding / lifting switch. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Replace driver seat control unit. Refer to Removal and Installation.

NO>>

Replace power seat switch LH. Refer to Removal and Installation.

Component Inspection

CHECK SLIDING / LIFTING SWITCH

  1. Ignition switch OFF.

  2. Disconnect power seat switch LH connector.

  3. Check resistance between power seat switch LH terminals.

    Power seat switch LHConditionResistance: (kΩ)
    Terminals
    1 4 Sliding switch Operate (forward) 4.485 – 4.575
    Operate (backward) 2.673 – 2.727
    Lifting switch Operate (upward) 0.418 – 0.426
    Operate (downward) 0.258 – 0.264
    Sliding / lifting switch release 29.700 – 30.300

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace power seat switch LH. Refer to Removal and Installation.

B2920-09 Driver Seat Control Unit Nissan Pathfinder R53

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC detection condition
B2920-09

Driver seat control unit

(Driver seat control unit)
Diagnosis condition The power consumption control of driver seat control unit is in wake-up state
Signal (terminal) —
Threshold Detects internal relay fixing
Diagnosis delay time 1 second or more

POSSIBLE CAUSE

Driver seat control unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Select “Self Diagnostic Result” mode of “AUTO DRIVE POS.”.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

REPLACE DRIVER SEAT CONTROL UNIT

Replace driver seat control unit. Refer to Removal and Installation.

>>

Inspection End.

B2921-A2 Driver Seat Control Unit Nissan Pathfinder 5th Gen

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC detection condition
B2921-A2

Driver seat control unit

(Driver seat control unit)
Diagnosis condition The power consumption control of driver seat control unit is in wake-up state
Signal (terminal) Battery power supply (terminal #48)
Threshold 8 V or less
Diagnosis delay time 1 second or more

POSSIBLE CAUSE

  • Fuse

  • Driver seat control unit battery power supply harness is open or shorted

  • Driver seat control unit

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Select “Self Diagnostic Result” mode of “AUTO DRIVE POS.”.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK FUSE

  1. Ignition switch OFF.

  2. Check that the following fuse is not blown (open):

    Signal nameFuse No.Capacity
    Battery power supply 54 20 A

Is the fuse blown (open)?

YES>>

Replace the blown (open) fuse after repairing the affected circuit if a fuse is blown (open).

NO>>

GO TO 2.

CHECK BATTERY POWER SUPPLY VOLTAGE

  1. Disconnect driver seat control unit connector.

  2. Check voltage between driver seat control unit harness connector and ground.

    (+)(—)

    Voltage

    (Approx.)
    Driver seat control unit
    ConnectorTerminal
    B210 48 Ground Battery voltage

Is the inspection result normal?

YES>>

Replace driver seat control unit. Refer to Removal and Installation.

NO>>

Repair the driver seat control unit battery power supply circuit.

B2921-A3 Driver Seat Control Unit Nissan Pathfinder 5th Gen

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC detection condition
B2921-A3

Driver seat control unit

(Driver seat control unit)
Diagnosis condition The power consumption control of driver seat control unit is in wake-up state
Signal (terminal) Battery power supply (terminal #48)
Threshold 18 V or more
Diagnosis delay time 1 second or more

POSSIBLE CAUSE

Charging system

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Select “Self Diagnostic Result” mode of “AUTO DRIVE POS.”.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK CHARGING SYSTEM

Perform trouble diagnosis for charging system. Refer to Work Flow (With 165-DSS-5000P) or Work Flow (Without 165-DSS-5000P).

>>

Inspection End.

U2118-87 Can Comm Err (intelligent Key) Nissan Pathfinder SUV

DTC Description

CAN (Controller Area Network) is a serial communication line for real time applications. It is an on-Nissan Pathfinder vehicle multiplex communication line with high data communication speed and excellent error detection ability. Modern Nissan Pathfinder vehicle is equipped with many electronic control unit, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with 2 communication lines (CAN-High line, CAN-Low line) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only.

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC detection condition
U2118-87

CAN comm err (Intelligent Key)

[Controller area network communication error (Intelligent Key)]
Diagnosis condition When ignition switch is ON
Signal (terminal) CAN communication signal
Threshold When driver seat control unit cannot communicate CAN communication signal
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

—

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 2 seconds or more.

  2. Select “Self Diagnostic Result” mode of “AUTO DRIVE POS.”.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK CAN COMMUNICATION SYSTEM

Perform trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

>>

Inspection End.

Power Supply and Ground Circuit (driver Seat Control Unit) Nissan Pathfinder SUV

Diagnosis Procedure

CHECK FUSE

  1. Ignition switch OFF.

  2. Check that the following fuse is not blown (open):

    Signal nameFuse No.Capacity
    Battery power supply 54 20 A

Is the fuse blown (open)?

YES>>

Replace the blown (open) fuse after repairing the affected circuit if a fuse is blown (open).

NO>>

GO TO 2.

CHECK BATTERY POWER SUPPLY VOLTAGE

  1. Disconnect driver seat control unit connector.

  2. Check voltage between driver seat control unit harness connector and ground.

    (+)(—)

    Voltage

    (Approx.)
    Driver seat control unit
    ConnectorTerminal
    B210 48 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the driver seat control unit battery power supply circuit.

CHECK GROUND CIRCUIT (OPEN)

Check continuity between driver seat control unit harness connector and ground.

Driver seat control unit—Continuity
ConnectorTerminal
B210 51 Ground Yes

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Repair the harness or connector.

Sliding Switch Nissan Pathfinder Fifth generation

Component Function Check

CHECK FUNCTION

CONSULT

  1. Ignition switch ON.

  2. Select “Sliding switch (Forward)” and “Sliding switch (Backward)” in “Data Monitor” mode of “AUTO DRIVE POS.”.

  3. Check sliding switch signal under the following conditions:

Monitor itemConditionStatus
Sliding switch (Forward) Sliding switch Operate (forward) On
Release Off
Sliding switch (Backward) Sliding switch Operate (backward) On
Release Off

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK SLIDING SWITCH POWER SUPPLY VOLTAGE

  1. Ignition switch OFF.

  2. Disconnect power seat switch LH connector.

  3. Ignition switch ON.

  4. Check voltage between power seat switch LH harness connector and ground.

    (+)(—)

    Voltage

    (Approx.)
    Power seat switch LH
    ConnectorTerminal
    B208 4 Ground 5 V

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 2.

CHECK SLIDING SWITCH SIGNAL CIRCUIT (OPEN)

  1. Ignition switch OFF.

  2. Disconnect driver seat control unit connector.

  3. Check continuity between power seat switch LH harness connector and driver seat control unit harness connector.

    Power seat switch LHDriver seat control unitContinuity
    ConnectorTerminalConnectorTerminal
    B208 4 B209 31 Yes

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the harness or connector.

CHECK SLIDING SWITCH SIGNAL CIRCUIT (SHORT TO GROUND)

Check continuity between power seat switch LH harness connector and ground.

Power seat switch LH—Continuity
ConnectorTerminal
B208 4 Ground No

Is the inspection result normal?

YES>>

Replace driver seat control unit. Refer to Removal and Installation.

NO>>

Repair the harness or connector.

CHECK SLIDING SWITCH

Check sliding switch. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace power seat switch LH. Refer to Removal and Installation.

Component Inspection

CHECK SLIDING SWITCH

  1. Ignition switch OFF.

  2. Disconnect power seat switch LH connector.

  3. Check resistance between power seat switch LH terminals.

    Power seat switch LHConditionResistance (kΩ)
    Terminals
    1 4 Sliding switch Operate (forward) 4.485 – 4.575
    Operate (backward) 2.673 – 2.727
    Release 29.700 – 30.300

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace power seat switch LH. Refer to Removal and Installation.

Seat Memory Switch Nissan Pathfinder R53

Component Function Check

CHECK FUNCTION

CONSULT

  1. Ignition switch ON.

  2. Select “Memory switch 1”, “Memory switch 2” and “Set switch” in “Data Monitor” mode of “AUTO DRIVE POS.”.

  3. Check seat memory switch signal under the following conditions:

Monitor itemConditionStatus
Memory switch 1 Memory switch-1 Press On
Release Off
Memory switch 2 Memory switch-2 Press On
Release Off
Set switch Set switch Press On
Release Off

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK SEAT MEMORY SWITCH POWER SUPPLY VOLTAGE

  1. Ignition switch OFF.

  2. Disconnect seat memory switch connector.

  3. Ignition switch ON.

  4. Check voltage between seat memory switch harness connector and ground.

    (+)(—)

    Voltage

    (Approx.)
    Seat memory switch
    ConnectorTerminal
    D60 1 Ground Battery voltage
    6
    7

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 2.

CHECK SEAT MEMORY SWITCH SIGNAL CIRCUIT (OPEN)

  1. Ignition switch OFF.

  2. Disconnect driver seat control unit connector.

  3. Check continuity between seat memory switch harness connector and driver seat control unit harness connector.

    Seat memory switchDriver seat control unitContinuity
    ConnectorTerminalConnectorTerminal
    D60 1 B209 10 Yes
    6 12
    7 9

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the harness or connector.

CHECK SEAT MEMORY SWITCH SIGNAL CIRCUIT (SHORT TO GROUND)

Check continuity between seat memory switch harness connector and ground.

Seat memory switch—Continuity
ConnectorTerminal
D60 1 Ground No
6
7

Is the inspection result normal?

YES>>

Replace driver seat control unit. Refer to Removal and Installation.

NO>>

Repair the harness or connector.

CHECK SEAT MEMORY SWITCH GROUND CIRCUIT (OPEN)

  1. Ignition switch OFF.

  2. Check continuity between seat memory switch harness connector and ground.

    Seat memory switch—Continuity
    ConnectorTerminal
    D60 8 Ground Yes

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair the harness or connector.

CHECK SEAT MEMORY SWITCH

Check seat memory switch. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace seat memory switch. Refer to Removal and Installation.

Component Inspection

CHECK SEAT MEMORY SWITCH

  1. Ignition switch OFF.

  2. Disconnect seat memory switch connector.

  3. Check continuity between seat memory switch terminals.

    Seat memory switchConditionContinuity
    Terminals
    8 7 Memory switch-1 Press Yes
    Release No
    1 Memory switch-2 Press Yes
    Release No
    6 Set switch Press Yes
    Release No

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace seat memory switch. Refer to Removal and Installation.

Power Seat Switch Lh Ground Circuit Nissan Pathfinder Fifth generation

Diagnosis Procedure

CHECK POWER SEAT SWITCH GROUND CIRCUIT (OPEN)

  1. Ignition switch OFF.

  2. Disconnect power seat switch LH connector and driver seat control unit connector.

  3. Check continuity between power seat switch LH harness connector and driver seat control unit harness connector.

    Power seat switch LHDriver seat control unitContinuity
    ConnectorTerminalConnectorTerminal
    B208 1 B209 32 Yes

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Repair the harness or connector.

Sliding Sensor Nissan Pathfinder SUV

Component Function Check

CHECK FUNCTION

CONSULT

  1. Ignition switch ON.

  2. Select “Sliding motor position” in “Data Monitor” mode of “AUTO DRIVE POS.”.

  3. Check sliding sensor signal under the following conditions:

Monitor itemConditionStatus
Sliding motor position Seat sliding Operate (forward) Change (increase)
Operate (backward) Change (decrease)
Other than the above No change

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK SLIDING SENSOR SIGNAL

Check signal between driver seat control unit harness connector and ground with oscilloscope.

(+)(—)Condition

Signal

(Reference value)
Driver seat control unit
ConnectorTerminal
B209 35 Ground Seat sliding Operate
Other than the above 5 V*

*: When the power consumption control of driver seat control unit is in wake-up state.

Is the inspection result normal?

YES>>

Replace driver seat control unit. Refer to Removal and Installation.

NO>>

GO TO 2.

CHECK SLIDING SENSOR SIGNAL CIRCUIT (OPEN)

  1. Ignition switch OFF.

  2. Disconnect driver seat control unit connector and sliding motor LH connector.

  3. Check continuity between driver seat control unit harness connector and sliding motor LH harness connector.

    Driver seat control unitSliding motor LHContinuity
    ConnectorTerminalConnectorTerminal
    B209 35 B211 3 Yes

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the harness or connector.

CHECK SLIDING SENSOR SIGNAL CIRCUIT (SHORT TO GROUND)

Check continuity between driver seat control unit harness connector and ground.

Driver seat control unit—Continuity
ConnectorTerminal
B209 35 Ground No

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair the harness or connector.

CHECK SLIDING SENSOR POWER SUPPLY VOLTAGE

  1. Connect driver seat control unit connector.

  2. Check voltage between sliding motor LH harness connector and ground.

    (+)(—)

    Voltage

    (Approx.)
    Sliding motor LH
    ConnectorTerminal
    B211 4 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

GO TO 5.

CHECK SLIDING SENSOR POWER SUPPLY CIRCUIT (OPEN)

  1. Disconnect driver seat control unit connector.

  2. Check continuity between sliding motor LH harness connector and driver seat control unit harness connector.

    Sliding motor LHDriver seat control unitContinuity
    ConnectorTerminalConnectorTerminal
    B211 4 B209 34 Yes

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair the harness or connector.

CHECK SLIDING SENSOR POWER SUPPLY CIRCUIT (SHORT TO GROUND)

Check continuity between sliding motor LH harness connector and ground.

Sliding motor LH—Continuity
ConnectorTerminal
B211 4 Ground No

Is the inspection result normal?

YES>>

Replace driver seat control unit. Refer to Removal and Installation.

NO>>

Repair the harness or connector.

CHECK SLIDING SENSOR GROUND CIRCUIT (OPEN)

  1. Disconnect driver seat control unit connector.

  2. Check continuity between sliding motor LH harness connector and driver seat control unit harness connector.

    Sliding motor LHDriver seat control unitContinuity
    ConnectorTerminalConnectorTerminal
    B211 2 B209 33 Yes

Is the inspection result normal?

YES>>

Replace sliding motor LH.

NO>>

Repair the harness or connector.

Tilt Sensor Nissan Pathfinder 2026

Component Function Check

CHECK FUNCTION

CONSULT

  1. Ignition switch ON.

  2. Select “TILT PULSE” in “Data Monitor” mode of “AUTO DRIVE POS.”.

  3. Check sliding tilt signal under the following conditions:

Monitor itemConditionStatus
TILT PULSE Tilt motor Operate (upward) Change (increase)
Operate (downward) Change (decrease)
Other than the above No change

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK TILT SENSOR SIGNAL

Check signal between automatic drive positioner control unit harness connector and ground with oscilloscope.

(+)(—)Condition

Signal

(Reference value)
Automatic drive positioner control unit
ConnectorTerminal
M33 7 Ground Steering tilt Operate
Other than the above 5 V*

*: When the power consumption control of automatic drive positioner control unit is in wake-up state.

Is the inspection result normal?

YES>>

Replace automatic drive positioner control unit. Refer to Removal and Installation.

NO>>

GO TO 2.

CHECK TILT SENSOR SIGNAL CIRCUIT (OPEN)

  1. Ignition switch OFF.

  2. Disconnect automatic drive positioner control unit connector and tilt motor connector.

  3. Check continuity between automatic drive positioner control unit harness connector and tilt motor harness connector.

    Automatic drive positioner control unitTilt motorContinuity
    ConnectorTerminalConnectorTerminal
    M33 7 M85 5 Yes

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the harness or connector.

CHECK TILT SENSOR SIGNAL CIRCUIT (SHORT TO GROUND)

Check continuity between automatic drive positioner control unit harness connector and ground.

Automatic drive positioner control unit—Continuity
ConnectorTerminal
M33 7 Ground No

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair the harness or connector.

CHECK TILT SENSOR POWER SUPPLY VOLTAGE

  1. Connect automatic drive positioner control unit connector.

  2. Check voltage between tilt motor harness connector and ground.

    (+)(—)

    Voltage

    (Approx.)
    Tilt motor
    ConnectorTerminal
    M85 4 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

GO TO 5.

CHECK TILT SENSOR POWER SUPPLY CIRCUIT (OPEN)

  1. Disconnect automatic drive positioner control unit connector.

  2. Check continuity between tilt motor harness connector and automatic drive positioner control unit harness connector.

    Tilt motorAutomatic drive positioner control unitContinuity
    ConnectorTerminalConnectorTerminal
    M85 4 M33 8 Yes

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair the harness or connector.

CHECK TILT SENSOR POWER SUPPLY CIRCUIT (SHORT TO GROUND)

Check continuity between tilt motor harness connector and ground.

Tilt motor—Continuity
ConnectorTerminal
M85 4 Ground No

Is the inspection result normal?

YES>>

Replace automatic drive positioner control unit. Refer to Removal and Installation.

NO>>

Repair the harness or connector.

CHECK TILT SENSOR GROUND CIRCUIT (OPEN)

  1. Disconnect automatic drive positioner control unit connector.

  2. Check continuity between tilt motor harness connector and automatic drive positioner control unit harness connector.

    Tilt motorAutomatic drive positioner control unitContinuity
    ConnectorTerminalConnectorTerminal
    M85 6 M33 9 Yes

Is the inspection result normal?

YES>>

Replace tilt motor. Refer to Removal and Installation.

NO>>

Repair the harness or connector.

Sliding Motor Nissan Pathfinder SUV

Component Function Check

CHECK FUNCTION

CONSULT

  1. Ignition switch ON.

  2. Select “Sliding motor” in “Active Test” mode of “AUTO DRIVE POS.”.

  3. Check sliding motor operation.

Test itemOperation
Sliding motor Forward Seat sliding Forward
Backward Backward
Stop Stop

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK SLIDING MOTOR POWER SUPPLY VOLTAGE

CONSULT

  1. Ignition switch OFF.

  2. Disconnect sliding motor LH connector.

  3. Ignition switch ON.

  4. Select “Sliding motor” in “Active Test” mode of “AUTO DRIVE POS.”.

  5. Check voltage between sliding motor LH harness connector and ground.

    (+)(—)Condition

    Voltage

    (Approx.)
    Sliding motor LH
    ConnectorTerminal
    B211 5 Ground Sliding motor Forward Battery voltage
    Backward 0 V
    Stop 0 V
    1 Forward 0 V
    Backward Battery voltage
    Stop 0 V

Is the inspection result normal?

YES>>

Replace sliding motor LH.

NO>>

GO TO 2.

CHECK SLIDING MOTOR POWER SUPPLY CIRCUIT (OPEN)

  1. Ignition switch OFF.

  2. Disconnect driver seat control unit connector.

  3. Check continuity between sliding motor LH harness connector and driver seat control unit harness connector.

    Sliding motor LHDriver seat control unitContinuity
    ConnectorTerminalConnectorTerminal
    B211 1 B210 44 Yes
    5 43

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the harness or connector.

CHECK SLIDING MOTOR POWER SUPPLY CIRCUIT (SHORT TO GROUND)

Check continuity between sliding motor LH harness connector and ground.

Sliding motor LH—Continuity
ConnectorTerminal
B211 1 Ground No
5

Is the inspection result normal?

YES>>

Replace driver seat control unit. Refer to Removal and Installation.

NO>>

Repair the harness or connector.

Lifting Motor (front) Nissan Pathfinder

Component Function Check

CHECK FUNCTION

CONSULT

  1. Ignition switch ON.

  2. Select “SEAT LIFTER FR” in “Active Test” mode of “AUTO DRIVE POS.”.

  3. Check lifting motor LH (front) operation.

Test itemOperation
SEAT LIFTER FR Up Lifting motor LH (front) Upward
Down Downward
Stop Stop

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK LIFTING MOTOR LH (FRONT) POWER SUPPLY VOLTAGE

CONSULT

  1. Ignition switch OFF.

  2. Disconnect lifting motor LH (front) connector.

  3. Ignition switch ON.

  4. Select “SEAT LIFTER FR” in “Active Test” mode of “AUTO DRIVE POS.”.

  5. Check voltage between lifting motor LH (front) harness connector and ground.

    (+)(—)Condition

    Voltage

    (Approx.)
    Lifting motor LH (front)
    ConnectorTerminal
    B202 1 Ground Lifting motor LH (front) Up Battery voltage
    Down 0 V
    Stop 0 V
    3 Up 0 V
    Down Battery voltage
    Stop 0 V

Is the inspection result normal?

YES>>

Replace seat cushion frame. Refer to Seat Cushion.

NO>>

GO TO 2.

CHECK LIFTING MOTOR LH (FRONT) POWER SUPPLY CIRCUIT (OPEN)

  1. Ignition switch OFF.

  2. Disconnect driver seat control unit connector.

  3. Check continuity between lifting motor LH (front) harness connector and driver seat control unit harness connector.

    Lifting motor LH (front)Driver seat control unitContinuity
    ConnectorTerminalConnectorTerminal
    B202 1 B210 53 Yes
    3 52

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the harness or connector.

CHECK LIFTING MOTOR LH (FRONT) POWER SUPPLY CIRCUIT (SHORT TO GROUND)

Check continuity between lifting motor LH (front) harness connector and ground.

Lifting motor LH (front)—Continuity
ConnectorTerminal
B202 1 Ground No
3

Is the inspection result normal?

YES>>

Replace driver seat control unit. Refer to Removal and Installation.

NO>>

Repair the harness or connector.

Telescopic Motor Nissan Pathfinder 5th Gen

Component Function Check

CHECK FUNCTION

CONSULT

  1. Ignition switch ON.

  2. Select “TELESCO MOTOR” in “Active Test” mode of “AUTO DRIVE POS.”.

  3. Check telescopic motor operation.

Test itemOperation
TELESCO MOTOR FR Steering telescopic Forward
RR Backward
Off Off

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK TELESCOPIC MOTOR POWER SUPPLY VOLTAGE

CONSULT

  1. Ignition switch OFF.

  2. Disconnect telescopic motor connector.

  3. Ignition switch ON.

  4. Select “TELESCOPIC MOTOR” in “Active Test” mode of “AUTO DRIVE POS.”.

  5. Check voltage between telescopic motor harness connector and ground.

    (+)(—)Condition

    Voltage

    (Approx.)
    Telescopic motor
    ConnectorTerminal
    M94 2 Ground Telescopic motor Forward Battery voltage
    Backward 0 V
    Stop 0 V
    1 Forward 0 V
    Backward Battery voltage
    Stop 0 V

Is the inspection result normal?

YES>>

Replace telescopic motor.

NO>>

GO TO 2.

CHECK TELESCOPIC MOTOR POWER SUPPLY CIRCUIT (OPEN)

  1. Ignition switch OFF.

  2. Disconnect automatic drive positioner control unit connector.

  3. Check continuity between telescopic motor harness connector and automatic drive positioner control unit harness connector.

    Telescopic motorAutomatic drive positioner control unitContinuity
    ConnectorTerminalConnectorTerminal
    M94 1 M34 17 Yes
    2 18

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair the harness or connector.

CHECK TELESCOPIC MOTOR POWER SUPPLY CIRCUIT (SHORT TO GROUND)

Check continuity between telescopic motor harness connector and ground.

Telescopic motor—Continuity
ConnectorTerminal
M94 1 Ground No
2

Is the inspection result normal?

YES>>

Replace automatic drive positioner control unit. Refer to Removal and Installation.

NO>>

Repair the harness or connector.

Seat Memeory Switch Indicator Nissan Pathfinder 2022

Component Function Check

CHECK FUNCTION

  1. Push set switch.

  2. Check memory indicator operation.

    When driver seat position is already retained in memory : Illuminated for 5 seconds
    When driver seat position is not retained in memory : Illuminated for 0.5 second

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK MEMORY INDICATOR OPERATION

Check memory indicator operation.

Which is the malfunctioning indicator?

All indicators are NG>>

GO TO 2.

An indicator is NG>>

GO TO 4.

CHECK FUSE

Check that the following fuse is not blown (open):

Signal nameFuse No.Capacity
Memory indicator power supply 26 5 A

Is the fuse blown (open)?

YES>>

Replace the blown (open) fuse after repairing the affected circuit if a fuse is blown (open).

NO>>

GO TO 3.

CHECK MEMORY INDICATOR POWER SUPPLY VOLTAGE

  1. Disconnect seat memory switch connector.

  2. Check voltage between seat memory switch harness connector and ground.

    (+)(—)

    Voltage

    (Approx.)
    Seat memory switch
    ConnectorTerminal
    D60 2 Ground Battery voltage

Is the inspection result normal?

YES>>

Replace seat memory switch. Refer to Removal and Installation.

NO>>

Repair the memory indicator power supply circuit.

CHECK MEMORY INDICATOR SIGNAL VOLTAGE

Check voltage between seat memory switch harness connector and ground.

(+)(—)

Voltage

(Approx.)
Seat memory switch
ConnectorTerminal
D60 3 Ground Battery voltage
4

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Replace seat memory switch. Refer to Removal and Installation.

CHECK MEMORY INDICATOR SIGNAL CIRCUIT (OPEN)

  1. Disconnect seat memory switch connector and driver seat control unit connector.

  2. Check continuity between seat memory switch harness connector and driver seat control unit harness connector.

    Seat memory switchDriver seat control unitContinuity
    ConnectorTerminalConnectorTerminal
    D60 3 B209 38 Yes
    4 18

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair the harness or connector.

CHECK MEMORY INDICATOR SIGNAL CIRCUIT (SHORT TO GROUND)

Check continuity between seat memory switch harness connector and ground.

Seat memory switch—Continuity
ConnectorTerminal
D60 3 Ground No
4

Is the inspection result normal?

YES>>

Replace driver seat control unit. Refer to Removal and Installation.

NO>>

Repair the harness or connector.