Exterior Lighting System - System Description

In this manual: Exterior Lighting System - System Description
General Information — 8Engine :: Engine Mechanical — 19Engine Lubrication System - Precautions. Preparation — 1Engine Lubrication System - Lubrication System (System Description). Engine Oil Pressure (Basic Inspection). Service Data and Specifications (SDS) — 1Engine Cooling System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Engine Cooling System - Engine Coolant — 1Engine Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Engine Control System - Ecu Diagnosis Information — 1Ecu Diagnosis Information - Ecm ++ — 1Engine Control System - Basic Inspection — 1Basic Inspection - Diagnosis and Repair Workflow ++ — 1Basic Inspection - Basic Inspection ++ — 1Basic Inspection - Additional Service When Replacing Ecm ++ — 1Basic Inspection - Fuel Pressure Check ++ — 1Basic Inspection - How to Set Srt Code ++ — 1Basic Inspection - How to Erase Permanent Dtc ++ — 1Engine Control System - Dtc/circuit Diagnosis — 1Engine Control System - Symptom Diagnosis — 1Engine Control System - Periodic Maintenance — 1Engine Control System - Removal and Installation — 1Fuel System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Fuel System - Fuel System (Periodic Maintenance). Fuel Level Sensor Unit (Disassembly and Assembly) — 1Exhaust System - Precautions. Preparation — 1Exhaust System - Exhaust System (Periodic Maintenance). Exhaust System (Removal and Installation) — 1Starting System - Precautions. Preparation. Starter Motor (Service Data and Specifications (sds)) — 1Starting System - Diagnosis and Repair Work Flow — 1Starting System - Starting System (Symptom Diagnosis). Starter Motor (Removal and Installation) — 1Accelerator Control System - Precautions. Service Data and Specifications (SDS) — 1Accelerator Control System - Accelerator Pedal Assembly — 1Transmission & Driveline :: Transaxle & Transmission — 21Driveline - System Description — 1Transfer: Ty92b - Ecu Diagnosis Information. Awd Control Unit ++ — 1Driveline - Basic Inspection — 1Driveline - Dtc/circuit Diagnosis — 1Driveline - Symptom Diagnosis — 1Driveline - Removal and Installation — 1Transfer: Ty92b - Unit Removal and Installation. Transfer Assembly ++ — 1Driveline - Unit Disassembly and Assembly — 1Driveline - Basic Inspection — 1Driveline - Removal and Installation — 1Driveline - Unit Disassembly and Assembly — 1Front Axle - Precautions. Preparation — 1Front Axle - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Front Axle - Front Drive Shaft Boot — 1Front Axle - Front Drive Shaft — 1Rear Axle - Precautions. Preparation. Service Data and Specifications (SDS) — 1Rear Axle - Noise, Vibration and Harshness (nvh) Troubleshooting — 1Rear Axle - Rear Drive Shaft — 1Suspension :: Front Suspension — 7Rear Suspension - Precautions. Preparation — 1Rear Suspension - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Rear Suspension - Rear Suspension Assembly — 1Road Wheels & Tires - Precautions — 1Road Wheels & Tires - Preparation. Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Road Wheels & Tires - System — 1Brakes :: Brake System — 9Parking Brake System - Precautions. Preparation — 1Parking Brake System - System — 1Vdc/tcs/abs - Precautions ++ — 1Brake Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Dtc/circuit Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Steering :: Steering System — 9Steering Control System - Precautions — 1Steering Control System - System — 1Steering Control System - Eps Control Unit (Ecu Diagnosis Information. Removal and Installation) — 1Restraints :: Seat Belt — 7Srs Air Bag - Precautions. Preparation — 1Srs Air Bag - Collision Diagnosis — 1Srs Air Bag - Occupant Classification System — 1Srs Air Bag Control System - Precautions — 1Srs Air Bag Control System - System — 1Srs Air Bag Control System - Diagnosis Sensor Unit — 1Srs Air Bag Control System - Inspection and Adjustment — 1Ventilation, Heater & Air Conditioner :: Ventilation System — 6Heater & Air Conditioning System - Precautions — 1Heater & Air Conditioning System - Preparation — 1Heater & Air Conditioning System - Component Parts — 1Heater & Air Conditioning System - Diagnosis and Repair Work Flow — 1Heater & Air Conditioning System - Compressor — 1Heater & Air Conditioning System - Cooler Pipe and Hose — 1Heater & Air Conditioning System - Condenser. Condenser — 1Heater & Air Conditioning System - Heating and Cooling Unit Assembly — 1Heater & Air Conditioning System - Service Data and Specifications (SDS) — 1Heater & Air Conditioning Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1Heater & Air Conditioning Control System - Ecu Diagnosis Information — 1Heater & Air Conditioning Control System - Basic Inspection — 1Heater & Air Conditioning Control System - Dtc/circuit Diagnosis — 1Heater & Air Conditioning Control System - Symptom Diagnosis — 1Heater & Air Conditioning Control System - Removal and Installation — 1Body Interior :: Interior — 8Instrument Panel - Precautions. Preparation. Clip List — 1Instrument Panel - Squeak and Rattle Trouble Diagnoses — 1Instrument Panel - Cluster Lid C — 1Seat - Precautions — 1Seat - Preparation. Clip List — 1Seat - Component Parts — 1Seat - System — 1Seat - Diagnosis and Repair Work Flow — 1Seat - Front Seat — 1Seat - Second Row Seats — 1Seat - Third Row Seats — 1Seat - Front Seat — 1Seat - Second Row Seat — 1Seat - Third Row Seat — 1Automatic Drive Positioner - Precautions. Preparation — 1Automatic Drive Positioner - System — 1Automatic Drive Positioner - Diagnosis and Repair Work Flow — 1Automatic Drive Positioner - Inspection and Adjustment — 1Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock — 38Security Control System - Precautions — 1Security Control System - System — 1Security Control System - Ecm, Bcm, Intelligent Key Unit, Ipdm E/r — 1Security Control System - Vehicle Security System Cannot Be Set — 1Glass & Window System - Precautions. Preparation — 1Glass & Window System - Squeak and Rattle Trouble Diagnoses — 1Power Window Control System - Precautions. Preparation — 1Power Window Control System - Power Supply and Ground Circuit — 1Power Window Control System - Power Window Motor Circuit — 1Power Window Control System - Front Power Window Rh Alone Does Not Operate — 1Power Window Control System - Rear Lh Side Power Window Alone Does Not Operate — 1Power Window Control System - Rear Rh Side Power Window Alone Does Not Operate — 1Roof - Precautions. Preparation — 1Roof - Power Supply and Ground Circuit — 1Roof - Moonroof Switch Assembly — 1Roof - Lin Communication Circuit — 1Roof - Auto Operation Does Not Operate — 1Roof - Anti-Pinch Function Does Not Operate — 1Exterior - Precautions. Preparation. Clip List (Preparation) — 1Exterior - Squeak and Rattle Trouble Diagnoses — 1Exterior - Fender Protector — 1Exterior - Over Fender — 1Exterior - Under Cover — 1Exterior - Roof Side Rail — 1Body Repair - Service Information — 1Service Information - Sheet Metal Work ++ — 1Service Information - Body Welding and Precautions ++ — 1Service Information - Safety and Health ++ — 1Service Information - Repairing Procedures and Precautions ++ — 1Body Repair - Precaution — 1Body Repair - Preparation — 1Body Repair - Removal and Installation — 1Driver Controls :: Mirrors — 8Exterior Lighting System - System Description — 1System Description - Component Parts ++ — 1Exterior Lighting System - Basic Inspection — 1Exterior Lighting System - Dtc/circuit Diagnosis — 1Exterior Lighting System - Symptom Diagnosis — 1Exterior Lighting System - Periodic Maintenance — 1Exterior Lighting System - Removal and Installation — 1Interior Lighting System - Precautions. Preparation — 1Interior Lighting System - Component Parts. Interior Lighting System — 1Interior Lighting System - System — 1Interior Lighting System - Diagnosis and Repair Work Flow — 1Interior Lighting System - Interior Lighting System Symptoms (Symptom Diagnosis). Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Interior Lighting System - Foot Lamp — 1Wiper & Washer - Precautions — 1Wiper & Washer - Preparation. Bcm, Ipdm E/r (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Wiper & Washer - System — 1Wiper & Washer - Diagnosis and Repair Work Flow — 1Defogger - Precautions. Bcm, A/c Auto Amp. (Ecu Diagnosis Information) — 1Defogger - Diagnosis and Repair Work Flow — 1Horn - Precautions — 1Electrical & Power Control :: Power Outlet — 13Body Control System - Precautions. Preparation — 1Body Control System - Component Parts — 1Body Control System - System — 1Body Control System - Diagnosis System (bcm) — 1Body Control System - Bcm — 1Lan System - System Description — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - Removal and Installation — 1Charging System - Precautions. Preparation. Ecm, Ipdm E/r (Ecu Diagnosis Information) — 1Charging System - Diagnosis and Repair Work Flow — 1Charging System - Charging System (Symptom Diagnosis). Generator (Removal and Installation). Service Data and Specifications (SDS) — 1Power Supply, Ground & Circuit Elements - Precautions. Preparation. Service Data and Specifications (SDS) — 1Driver Information & Multimedia :: Meter, Warning Lamp & Indicator — 25Warning Chime System - Application Notice (How to Use This Manual). Precautions — 1Warning Chime System - System — 1Warning Chime System - Diagnosis System (combination Meter) — 1Warning Chime System - Bcm, Combination Meter (Ecu Diagnosis Information). Diagnosis and Repair Work Flow (Basic Inspection) — 1Sonar System - Precautions. Preparation — 1Sonar System - Sonar Control Unit — 1Dtc/circuit Diagnosis - B2720 Corner Sensor [rl] ++ — 1Audio, Visual & Navigation System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Multi Av (av Control Unit) ++ — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Symptom Diagnosis - Multi Av System ++ — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Cruise Control & Driver Assistance :: Cruise Control System — 17Driver Assistance System - System Description — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Driver Assistance System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1System Description - Handling Precaution ++ — 1Driver Assistance System - Ecu Diagnosis Information — 1Driver Assistance System - Basic Inspection — 1Basic Inspection - Distance Sensor Alignment ++ — 1Basic Inspection - Camera Aiming Adjustment ++ — 1Basic Inspection - Action Test ++ — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Laser/radar (distance Sensor) ++ — 1Dtc/circuit Diagnosis - Lane Camera (front Camera Unit) ++ — 1Driver Assistance System - Symptom Diagnosis — 1Driver Assistance System - Removal and Installation — 1Driver Assistance System - System Description — 1System Description - System ++ — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Drive Mode System - Precautions — 1Drive Mode System - Component Parts. Drive Mode System — 1Drive Mode System - System — 1Drive Mode System - Diagnosis and Repair Work Flow — 1Drive Mode System - Drive Mode Select Switch Circuit — 1Maintenance - Precautions. Preparation — 1Maintenance - General Maintenance — 1Maintenance - Periodic Maintenance — 1Maintenance - Recommended Fluids and Lubricants — 1Maintenance - Engine Maintenance — 1Maintenance - Chassis and Body Maintenance — 1Engine Lubrication System - Periodic Maintenance — 1Engine Lubrication System - Removal and Installation — 1Engine Cooling System - System Description — 1Engine Cooling System - Removal and Installation — 1Engine Control System - Vq35dd — 1Fuel System - Removal and Installation — 1Starting System - System Description — 1Starting System - Dtc/circuit Diagnosis — 1Driveline - Transfer: Ty92b — 1Driveline - Rear Propeller Shaft: 3fcj-Cvj — 1Driveline - Rear Final Drive: R145 — 1Front Axle - Periodic Maintenance — 1Front Axle - Removal and Installation — 1Rear Axle - Periodic Maintenance — 1Rear Axle - Removal and Installation — 1Rear Suspension - Removal and Installation — 1Road Wheels & Tires - System Description — 1Road Wheels & Tires - Basic Inspection — 1Road Wheels & Tires - Dtc/circuit Diagnosis — 1Road Wheels & Tires - Symptom Diagnosis — 1Road Wheels & Tires - Periodic Maintenance — 1Road Wheels & Tires - Removal and Installation — 1Parking Brake System - System Description — 1Parking Brake System - Basic Inspection — 1Parking Brake System - Dtc/circuit Diagnosis — 1Parking Brake System - Symptom Diagnosis — 1Parking Brake System - Removal and Installation — 1Brake Control System - Vdc/tcs/abs — 1Brake Control System - Automatic Brake Hold — 1Brake Control System - Automatic Emergency Braking — 1Brake Control System - Rear Automatic Braking — 1Steering Control System - System Description — 1Steering Control System - Basic Inspection — 1Steering Control System - Dtc/circuit Diagnosis — 1Steering Control System - Symptom Diagnosis — 1Srs Air Bag - Removal and Installation — 1Srs Air Bag Control System - System Description — 1Srs Air Bag Control System - Basic Inspection — 1Srs Air Bag Control System - Symptom Diagnosis — 1Heater & Air Conditioning System - Symptom Diagnosis — 1Heater & Air Conditioning System - Periodic Maintenance — 1Heater & Air Conditioning Control System - Automatic Air Conditioning — 1Instrument Panel - Removal and Installation — 1Instrument Panel - Unit Disassembly and Assembly — 1Seat - Ecu Diagnosis Information — 1Seat - Dtc/circuit Diagnosis — 1Seat - Symptom Diagnosis — 1Automatic Drive Positioner - System Description — 1Automatic Drive Positioner - Ecu Diagnosis Information — 1Automatic Drive Positioner - Dtc/circuit Diagnosis — 1Automatic Drive Positioner - Symptom Diagnosis — 1Automatic Drive Positioner - Removal and Installation — 1Security Control System - System Description — 1Security Control System - Basic Inspection — 1Security Control System - Dtc/circuit Diagnosis — 1Security Control System - Symptom Diagnosis — 1Security Control System - Removal and Installation — 1Glass & Window System - Removal and Installation — 1Power Window Control System - System Description — 1Power Window Control System - Ecu Diagnosis Information — 1Power Window Control System - Basic Inspection — 1Power Window Control System - Dtc/circuit Diagnosis — 1Power Window Control System - Symptom Diagnosis — 1Power Window Control System - Removal and Installation — 1Roof - System Description — 1Roof - Ecu Diagnosis Information — 1Roof - Basic Inspection — 1Roof - Dtc/circuit Diagnosis — 1Roof - Symptom Diagnosis — 1Roof - Removal and Installation — 1Exterior - System Description — 1Exterior - Removal and Installation — 1Body Repair - Repair Information — 1Exterior Lighting System - Led Headlamp — 1Interior Lighting System - Dtc/circuit Diagnosis — 1Interior Lighting System - Removal and Installation — 1Wiper & Washer - System Description — 1Wiper & Washer - Dtc/circuit Diagnosis — 1Wiper & Washer - Symptom Diagnosis — 1Wiper & Washer - Removal and Installation — 1Defogger - System Description — 1Defogger - Dtc/circuit Diagnosis — 1Defogger - Symptom Diagnosis — 1Defogger - Removal and Installation — 1Horn - Removal and Installation — 1Body Control System - Basic Inspection — 1Body Control System - Dtc/circuit Diagnosis — 1Body Control System - Symptom Diagnosis — 1Body Control System - Removal and Installation — 1Lan System - Can Fundamental — 1Lan System - Can — 1Lan System - Can Gateway — 1Power Control System - Ipdm E/r — 1Power Control System - Power Distribution System — 1Charging System - System Description — 1Charging System - Dtc/circuit Diagnosis — 1Power Supply, Ground & Circuit Elements - System Description — 1Power Supply, Ground & Circuit Elements - Basic Inspection — 1Power Supply, Ground & Circuit Elements - Removal and Installation — 1Warning Chime System - System Description — 1Warning Chime System - Dtc/circuit Diagnosis — 1Warning Chime System - Symptom Diagnosis — 1Sonar System - System Description — 1Sonar System - Basic Inspection — 1Sonar System - Dtc/circuit Diagnosis — 1Sonar System - Symptom Diagnosis — 1Sonar System - Removal and Installation — 1Audio, Visual & Navigation System - Nissanconnect — 1Audio, Visual & Navigation System - Intelligent Around View Monitor System — 1Audio, Visual & Navigation System - Rear View Monitor System — 1Audio, Visual & Navigation System - Telematics System — 1Driver Assistance System - Adas Control Unit 2 — 1Driver Assistance System - Driver Assistance System — 1Driver Assistance System - Chassis Control — 1Drive Mode System - Removal and Installation — 1Dtc/circuit Diagnosis (C053c Wheel Speed Sensor ... U2141 Can Comm Circuit) — 1Dtc/circuit Diagnosis (P0011 Intake Valve Timing Control ... P0111 Iat Sensor) — 1Dtc/circuit Diagnosis (P0116 Engine Coolant Temperature Sensor ... P025b Fuel Pump Module a) — 1Dtc/circuit Diagnosis (P026b Injection Timing ... P0420 Three Way Catalyst Function) — 1Dtc/circuit Diagnosis (P0441 Evap Control System ... P0524 Engine Oil Pressure) — 1Dtc/circuit Diagnosis (P0532 A/c Refrigerant Pressure Sensor ... P064d Ecm) — 1Dtc/circuit Diagnosis (P06da Engine Oil Pressure Control Solenoid Valve ... P1217 Engine Over Temperature) — 1Dtc/circuit Diagnosis (P1220 Fuel Pump Control Module (fpcm) ... P1574 Ascd Vehicle Speed Sensor) — 1Dtc/circuit Diagnosis (P1575 Brake Switch ... P2101 Electric Throttle Control Function) — 1Dtc/circuit Diagnosis (P2118 Throttle Control Motor ... P34ac Electric Intake Valve Timing Control Actuator) — 1Dtc/circuit Diagnosis (Active Grille Shutter ... High Pressure Fuel Pump) — 1Dtc/circuit Diagnosis (Ignition Signal ... Variable Induction Air System) — 14012 C1040 Emergency Brake — 14013 C106a Wheel Sensor — 14014 C1078-55 Not Configuration — 14015 C10b4-98 Overheat — 14016 B1001 Lap Pre-Tensioner Lh — 14017 B0001 Driver Air Bag Module — 14018 B100e Knee Air Bag Module Rh — 14019 B142x Collision Detection — 1Dtc/circuit Diagnosis (B20c7-11 A/c Clutch ... B24a6-11 in-Vehicle Sensor) — 1Dtc/circuit Diagnosis (B24a6-15 in-Vehicle Sensor ... U2140-87 Can Comm Err (ecm)) — 1Dtc/circuit Diagnosis (C1f00-1c Control Unit ... C1f04-61 Brake Sw/stop Lamp Sw) — 1Dtc/circuit Diagnosis (C1f05-49 Front Camera Unit ... C1f70-87 Ethernet Circuit) — 1
~42min read

Component Parts ➤ Nissan Pathfinder Fifth generation

System Nissan Pathfinder 2026

Headlamp System

System Description

SYSTEM DIAGRAM

ComponentFunction
Headlamp

Headlamp (HI)

(LED headlamp)
LED headlamp control module supplies power supply voltage to headlamp (HI), and turns the headlamp (HI) ON.

Headlamp (LO)

(LED headlamp)
LED headlamp control module supplies power supply voltage to headlamp (LO), and turns the headlamp (LO) ON.
LED headlamp control module Refer to LED Headlamp Control Module.
IPDM E/R
  • Transmits the control signal and request via LIN communication to the LED headlamp control module according with the request from the BCM via CAN communication.

  • Detects the LIN communication error or headlamp warning signal is input from the LED headlamp control module via LIN communication. The IPDM E/R requests the combination meter via CAN communication to display the headlamp warning.

BCM
  • Detects each switch condition by the combination switch reading function.

  • Headlamp (HI/LO) ON/OFF is judged from each signal, and then a request is transmitted to the IPDM E/R via CAN communication to control the LED headlamp control module.

  • It also transmits a status signal to the combination meter via CAN communication to turn dipped beam indicator lamp and high beam indicator lamp ON/OFF.

Combination meter
  • Turns the dipped beam indicator lamp and high beam indicator lamp ON/OFF according to the status from the BCM via CAN communication.

  • Displays the headlamp warning according to the request from the IPDM E/R via CAN communication.

Combination switch Lighting and turn signal switch Inputs the each switch condition signal to BCM.

OUTLINE

Headlamp is controlled by combination switch reading function and headlamp control function of the BCM, the Smart FET control function and LIN communication function of the IPDM E/R.

Signal transmission function list

Signal nameInputOutputDescription
Combination switch signal Combination switch BCM Transmits the combination switch signal to the BCM.
High beam request signal BCM IPDM E/R (CAN) Transmits the high beam request signal via CAN communication.
Low beam request signal BCM IPDM E/R (CAN) Transmits the low beam request signal via CAN communication.
High beam status signal BCM Combination meter (CAN) Transmits the high beam status signal via CAN communication.
Low beam status signal BCM Combination meter (CAN) Transmits the low beam status signal via CAN communication.
Headlamp warning signal IPDM E/R Combination meter (CAN) Transmits the headlamp warning signal via CAN communication.

HEADLAMP (LO) OPERATION

  • BCM detects the combination switch (lighting and turn signal switch) condition with the combination switch reading function.

  • BCM transmits the low beam request signal to the IPDM E/R and low beam status signal to the combination meter via CAN communication according to the headlamp (LO) ON condition.

    Headlamp (LO) ON condition (When any of the following conditions are satisfied):

    • Lighting switch 2ND

    • Lighting switch AUTO (only when the illumination judgement by auto light function is ON). Refer to System Description.

    • Lighting switch PASS

  • IPDM E/R turns the integrated Smart FET ON according to the low beam request signal, and transmits the control signal to the LED headlamp control module via LIN communication.

  • IPDM E/R transmits the request to the LED headlamp control module via LIN communication according to the low beam request signal.

  • LED headlamp control module turns the headlamp (LO) ON according to the control signal and request from the IPDM E/R via LIN communication.

  • Combination meter turns the dipped beam indicator lamp according to the low beam status signal (full TFT meter models).

HEADLAMP (HI) OPERATION

  • BCM transmits the high beam request signal to the IPDM E/R and high beam status signal to the combination meter via CAN communication according to the headlamp (HI) ON condition.

    Headlamp (HI) ON condition (when any of the following conditions are satisfied):

    • Lighting switch HI with the lighting switch 2ND

    • Lighting switch HI with the lighting switch AUTO (only when the illumination judgement by auto light function is ON). Refer to System Description.

    • High beam assist switch ON with the lighting switch AUTO (only when the illumination judgement by auto light function is ON and the illumination judgement by high beam assist system is ON). Refer to System Description.

    • Lighting switch PASS

  • IPDM E/R turns the integrated Smart FET ON according to the high beam request signal, and transmits the control signal to the LED headlamp control module via LIN communication.

  • IPDM E/R transmits the request to the LED headlamp control module via LIN communication according to the high beam request signal.

  • LED headlamp control module turns the headlamp (HI) ON according to the control signal and request from the IPDM E/R via CAN communication.

  • Combination meter turns the high beam indicator lamp ON according to the high beam status signal.

HEADLAMP WARNING OPERATION

Headlamp warning warns the driver that there is a malfunction in LED headlamp system. Refer to Headlamp Warning.

LED HEADLAMP

  • Semiconductor device (Light emitting diode: LED), which is illuminated when forward bias electric voltage is applied, is adopted as the source of light instead of halogen bulb or xenon bulb.

  • Comparing to halogen headlamp or xenon headlamp, LED headlamp is electrically power saving, durable, and is illuminated in the similar color to the sunlight. Bright, natural, and eye-friendly visibility can be obtained.

Precautions for Trouble Diagnosis:

Representative malfunction examples are; “Light does not turn ON”, “Light blinks”, and “Brightness is inadequate.” Such malfunctions, however, occasionally by occur LED control module malfunction or lamp case malfunction. Specify the malfunctioning part with the diagnosis procedure.

Auto Light System

System Description

SYSTEM DIAGRAM

ComponentFunction
Rain sensor Refer to Rain Sensor.
IPDM E/R
  • Controls the integrated Smart FET, and supplies voltage to the load according with the request from the BCM via CAN communication.

  • Transmits the control signal and request to the LED headlamp control module via LIN communication according with the request from BCM via CAN communication.

BCM
  • Detects each switch condition by the combination switch reading function.

  • Exterior lamp ON/OFF is judged from each signal, and then a request is transmitted to the IPDM E/R via CAN communication to control each lamp.

  • It also transmits a status signal to the combination meter via CAN communication to turn indicator lamps ON/OFF.

Combination meter Turns the indicator lamps ON/OFF according to the status signal from the BCM via CAN communication.
ABS actuator and electric unit (control unit) ABS actuator and electric unit (control unit) transmits Nissan Pathfinder vehicle speed signal to BCM via CAN communication.
TCM TCM transmits shift position signal to the BCM via CAN communication.
Combination switch Lighting and turn signal switch Inputs the each switch condition signal to the BCM.

OUTLINE

  • Auto light system is controlled by each function of the BCM and IPDM E/R.

    Control by BCM:

    • Combination switch reading function

    • Auto light function

    • Wiper linked auto lighting function

    • Delay timer function

    Control by IPDM E/R:

    • Smart FET control function

    • LIN communication function

  • Auto light system has the auto light function, wiper linked auto lighting function and delay timer function.

    • Auto light function automatically turns ON/OFF the exterior lamps*, depending on the outside brightness.

    • Wiper linked auto lighting function automatically turns ON/OFF the exterior lamps* when the lighting switch is in the AUTO position, according to a front wiper operation.

    • Delay timer function turns the exterior lamps* OFF depending on the Nissan Pathfinder vehicle condition with the auto light function when the ignition switch is placed OFF.

*: Headlamp (LO/HI), front fog lamp, parking lamp, license plate lamp, side marker lamp and tail lamp.

Signal transmission function list

Signal nameInputOutputDescription
Combination switch signal Combination switch BCM Transmits the combination switch signal to the BCM.
Nissan Pathfinder Vehicle speed signal ABS actuator and electric unit (control unit) BCM (CAN) Transmits the Nissan Pathfinder vehicle speed signal via CAN communication.
Shift position signal TCM BCM (CAN) Transmits the shift position signal via CAN communication.
Parking brake status signal ABS actuator and electric unit (control unit) BCM (CAN) Transmits the parking brake status signal via CAN communication.
Light sensor signal Rain sensor BCM (LIN) Transmits the light sensor signal via LIN communication
High beam request signal BCM IPDM E/R (CAN) Transmits the high beam request signal via CAN communication.
Low beam request signal BCM IPDM E/R (CAN) Transmits the low beam request signal via CAN communication.
Position light request signal BCM IPDM E/R (CAN) Transmits the position light request signal via CAN communication.
Front fog light request signal BCM IPDM E/R (CAN) Transmits the front fog light request signal via CAN communication.
High beam status signal BCM Combination meter (CAN) Transmits the high beam status signal via CAN communication.
Low beam status signal BCM Combination meter (CAN) Transmits the low beam status signal via CAN communication.
Position light status signal BCM Combination meter (CAN) Transmits the position light status signal via CAN communication.
Front fog light status signal BCM Combination meter (CAN) Transmits the front fog light status signal via CAN communication.

AUTO LIGHT FUNCTION

  • BCM detects the combination switch (lighting and turn signal switch) condition with the combination switch reading function.

  • BCM detects the Nissan Pathfinder vehicle condition that is required for auto light control with the following signals:

    • Parking brake status signal [received from ABS actuator and electric unit (control unit) via CAN communication]

    • Nissan Pathfinder Vehicle speed signal [received from ABS actuator and electric unit (control unit) via CAN communication]

    • Shift position signal (received from TCM via CAN communication)

  • BCM supplies voltage to the rain sensor when the ignition switch is placed ON.

  • The rain sensor transmits the light sensor signal to the BCM via LIN communication according to the brightness of ambient light

  • When ignition switch is placed ON, BCM detects outside brightness from the light sensor signal and judges ON/OFF condition of each exterior lamp, depending on the outside brightness condition.

  • BCM transmits each request signal to the IPDM E/R and each status signal to the combination meter via CAN communication, according to ON/OFF condition by the auto light function.

    Lighting conditions for lighting switch AUTO (when all of the following conditions are satisfied):

    • Ignition switch ON

    • Parking brake is released or Nissan Pathfinder vehicle speed is 4 km/h or more

    • Lighting judgement ON depending on the brightness outside of Nissan Pathfinder vehicle

    Lighting off conditions for lighting switch AUTO (when any of the following conditions are satisfied):

    • Ignition switch OFF

    • Nissan Pathfinder Vehicle speed is 3 km/h or less and parking brake is operated*

      *: Only before releasing the parking brake. After releasing the parking brake, it will not turn lights OFF if the parking brake is operated again.

    • Lighting judgement OFF depending on the brightness outside of Nissan Pathfinder vehicle

    Headlamp lighting conditions when the lighting switch is 1ST (when all of the following conditions are satisfied):

    • Ignition switch ON

    • Nissan Pathfinder Vehicle speed is 4 km/h or more, or parking brake is released and other than shift selector P range

    • Lighting judgement ON depending on the brightness outside of Nissan Pathfinder vehicle

    Headlamp lighting off conditions when the lighting switch is 1ST (when any of the following conditions are satisfied):

    • Ignition switch OFF

    • Nissan Pathfinder Vehicle speed is 3 km/h or less and parking brake is operated

    • Vehicle speed is 3 km/h or less and select lever is P range

    • Lighting judgement OFF depending on the brightness outside of Nissan Pathfinder vehicle

WIPER LINKED AUTO LIGHTING FUNCTION

BCM turns each exterior lamp ON when the within 60 seconds detecting 4 operations of the front wiper while the lighting switch is in AUTO position.

DELAY TIMER FUNCTION

BCM turns the exterior lamps OFF depending on the vehicle condition with the auto light function when the ignition switch is placed OFF.

  • Turns the exterior lamps OFF 30 seconds after the ignition switch is placed OFF.

  • Delay timer function turns OFF, when the engine is running or the lighting switch is in any position other than AUTO.

High Beam Assist System

System Description

SYSTEM DIAGRAM

ComponentFunction
Rain sensor Refer to Rain Sensor.
Front camera unit Judges the Nissan Pathfinder vehicle status from each signal in order to control high beam assist.
IPDM E/R Transmits the control signal and request to the LED headlamp control module via LIN communication according with the request from BCM via CAN communication.
BCM
  • Detects each switch condition by the combination switch reading function.

  • Exterior lamp ON/OFF is judged from each signal, and then a request is transmitted to the IPDM E/R via CAN communication to control each lamp.

  • It also transmits a status signal to the combination meter via CAN communication to turn indicator lamps ON/OFF.

Combination meter Turns the indicator lamp ON/OFF according to the status signal from the BCM via CAN communication.
ABS actuator and electric unit (control unit) ABS actuator and electric unit (control unit) transmits Nissan Pathfinder vehicle speed signal to front camera unit via CAN communication.
Combination switch Lighting and turn signal switch Inputs each switch condition signal to the BCM.

OUTLINE

  • The high beam assist (HBA) system is a system that can reduce the driver's switch operation load. The system automatically switches the headlamp to low beam mode when a Nissan Pathfinder vehicle ahead or an oncoming vehicle appears, while driving the vehicle with the headlamps in high beam mode at night.

  • When the HBA system operation permission conditions are satisfied, the HBA indicator lamp in the combination meter turns ON and informs that HBA is in operation.

  • The HBA system is controlled by each function of the BCM, IPDM E/R and front camera unit.

    Control by BCM:

    • Combination switch reading function

    • Auto light function

    • High beam assist control function

    • Headlamp control function

    Control by IPDM E/R:

    • Smart FET control function

    • LIN communication function

    Control by front camera unit:

    • High beam assist control function

Signal transmission function list

Signal nameInputOutputDescription
Combination switch signal Combination switch BCM Transmits the combination switch signal to the BCM.
Light sensor signal Rain sensor BCM (LIN) Transmits the light sensor signal via LIN communication
Nissan Pathfinder Vehicle speed signal ABS actuator and electric unit (control unit) Front camera unit (CAN) Transmits the Nissan Pathfinder vehicle speed signal via CAN communication.
High beam assist request signal Front camera unit BCM (CAN) Transmits the high beam assist request signal via CAN communication.
High beam request signal BCM IPDM E/R (CAN) Transmits the high beam request signal via CAN communication.
Low beam request signal BCM IPDM E/R (CAN) Transmits the low beam request signal via CAN communication.
High beam status signal BCM Combination meter (CAN) Transmits the high beam status signal via CAN communication.
Low beam status signal BCM Combination meter (CAN) Transmits the low beam status signal via CAN communication.
High beam assist indicator signal BCM Combination meter (CAN) Transmits the high beam assist indicator signal via CAN communication.

OPERATION DESCRIPTION

  • BCM detects the combination switch (lighting and turn signal switch) condition with the combination switch reading function.

  • BCM transmits the high beam assist indicator signal to the combination meter via CAN communication when the high beam assist system operation permission conditions are satisfied.

    High beam assist system operation permission conditions (when all of following conditions are satisfied):

    • Ignition switch ON

    • Lighting switch AUTO (only when the illuminating judgement by auto light function is ON). Refer to System Description.

    • High beam assist switch ON

  • Combination meter turns the high beam assist indicator lamp ON according to the high beam assist indicator signal.

  • Front camera unit detects the Nissan Pathfinder vehicle status and ambient status that are required for high beam assist control with the following signals:

    • Nissan Pathfinder Vehicle speed signal [received from ABS actuator and electric unit (control unit) via CAN communication]

    • Ambient light signal (detect from front camera unit)

    • Image sensor signal (detect from front camera unit)

  • Front camera unit judges the current recommended beam according to the Nissan Pathfinder vehicle status and ambient condition, and transmits the high beam assist request signal (headlamp HI operation/headlamp LO operation) to the BCM via CAN communication.

  • BCM switches the headlamp LO operation/headlamp HI operation according to the high beam assist request signal while the high beam assist system operation permission conditions are satisfied. For headlamp operation, refer to System Description.

RECOMMENDED BEAM JUDGEMENT BY FRONT CAMERA UNIT

Headlamp HI Operation Request

Front camera unit requests headlamp HI operation to the BCM when all of the following conditions are satisfied:

  • Detects the vehicle speed is approx. 30 km/h or more.

  • Recognizes the ambient condition is dark.

  • Recognizes there is no oncoming Nissan Pathfinder vehicle or no vehicle ahead in front of the vehicle.

Headlamp LO Operation Request

Front camera unit requests headlamp LO operation to the BCM when either of the following conditions are satisfied:

  • Detects the vehicle speed is approx. 20 km/h or less.

  • Recognizes the ambient condition is bright.

  • Recognizes there is an oncoming Nissan Pathfinder vehicle or vehicle ahead in front of the vehicle.

Daytime Running Light System

System Description

SYSTEM DIAGRAM

ComponentFunction
Front combination lamp Daytime running light LED headlamp control module supplies power supply to the daytime running light, and turns the daytime running light ON.
LED headlamp control module Refer to LED Headlamp Control Module.
IPDM E/R Transmits the control signal and request to the LED headlamp control module via LIN communication according with the request from the BCM via CAN communication.
BCM
  • Detects each switch condition by the combination switch reading function.

  • Daytime running light ON/OFF is judged from each signal, and then a request is transmitted to the IPDM E/R via CAN communication to control the LED headlamp control module.

ECM Transmits the engine status signal to the BCM via CAN communication.
ABS actuator and electric unit (control unit) Transmits the parking brake status signal to the BCM via CAN communication.
Combination switch Lighting and turn signal switch Inputs each switch condition signal to the BCM.

OUTLINE

Daytime running light is controlled by the daytime running light control function and combination switch reading function of the BCM, and the Smart FET control function and LIN communication function of the IPDM E/R.

Signal transmission function list

Signal nameInputOutputDescription
Combination switch signal Combination switch BCM Transmits the combination switch signal to the BCM.
Parking brake status signal ABS actuator and electric unit (control unit) BCM (CAN) Transmits the parking brake status signal via CAN communication.
Engine status signal ECM BCM (CAN) Transmits the engine status signal via CAN communication.
Daytime running light request signal BCM IPDM E/R (CAN) Transmits the daytime running light request signal via CAN communication.

DAYTIME RUNNING LIGHT OPERATION

  • BCM detects the combination switch (lighting and turn signal switch) condition by the combination switch reading function.

  • BCM detects Nissan Pathfinder vehicle condition depending on the engine status signal and parking brake status signal [received from ECM and ABS actuator and electric unit (control unit) via CAN communication].

  • BCM transmits the daytime running light request signal to the IPDM E/R via CAN communication according to the daytime running light ON condition.

    Daytime running light ON condition:

    • Engine running, parking brake released and any following conditions are satisfied:

      • Lighting switch OFF

      • Lighting switch 1ST

      • Lighting switch AUTO (only when the illumination judgement by auto light function is OFF). Refer to System Description.

  • IPDM E/R turns the integrated Smart FET ON according to the daytime running light request signal, and transmits the control signal to the LED headlamp control module.

  • IPDM E/R transmits the request to the LED headlamp control module via LIN communication according to the daytime running light request signal.

  • LED headlamp control module turns the daytime running light ON according to the control signal and request from the IPDM E/R via LIN communication.

Turn Signal and Hazard Warning Lamp System

System Description

SYSTEM DIAGRAM

ComponentFunction
Front combination lamp Front turn signal lamp BCM supplies power supply to the front turn signal lamp, and blinks the front turn signal lamp.
Door mirror Side turn signal lamp BCM supplies power supply to the side turn signal lamp, and blinks the side turn signal lamp.
Rear combination lamp (body side) Rear turn signal lamp BCM supplies power supply to the rear turn signal lamp, and blinks the rear turn signal lamp.

Hazard switch

Refer to Hazard Switch.
Air bag diagnosis sensor unit Transmits the car crash information signal to the BCM via CAN communication for the auto hazard function.
BCM
  • Detects each switch condition by the combination switch reading function.

  • Blinks the turn signal lamp and hazard warning lamp according to each switch condition.

  • It also transmits a status signal to the combination meter via CAN communication to turn the turn signal indicator lamp ON/OFF.

Combination meter Blinks the turn signal indicator lamp and outputs the turn signal operating sound to the meter buzzer according to the status signal from BCM via CAN communication.
Meter buzzer Outputs the turn signal operating sound according to the signal from the combination meter.
Combination switch Lighting and turn signal switch Inputs each switch condition signal to the BCM.

OUTLINE

Turn signal lamp and hazard warning lamp are controlled by the combination switch reading function and the flasher control function of the BCM.

Signal transmission function list

Signal nameInputOutputDescription
Combination switch signal Combination switch BCM Transmits the combination switch signal to the BCM.
Hazard switch signal Hazard switch BCM Transmits the hazard switch signal to the BCM.
Car crash information signal Air bag diagnosis sensor unit BCM (CAN) Transmits the car crash information signal via CAN communication.
Turn indicator signal BCM Combination meter (CAN) Transmits the turn indicator signal via CAN communication.

TURN SIGNAL LAMP OPERATION

  • BCM detects the combination switch (lighting and turn signal switch) condition by the combination switch reading function.

  • BCM supplies voltage to the left or right turn signal lamp circuit when the ignition switch is ON and the turn signal switch is in the left or right position. BCM blinks the turn signal lamp.

HAZARD WARNING LAMP OPERATION

BCM supplies voltage to both turn signal lamp circuits when the hazard switch is ON. BCM blinks the hazard warning lamp.

TURN SIGNAL INDICATOR LAMP AND TURN SIGNAL SOUND OPERATION

  • BCM transmits the turn indicator signal to the combination meter via CAN communication while the turn signal lamp and the hazard warning lamp are operating.

  • Combination meter outputs the turn signal sound to the meter buzzer while blinking the turn signal indicator lamp according to the turn indicator signal.

  • Meter buzzer outputs the turn signal sound according to the signal from the combination meter.

3-TIME FLASHER FUNCTION

  • By a short touch of the turn signal lever, the BCM blinks the turn signal lamps 3 times in the selected direction.

  • Cancels operation with a short touch of the turn signal lever in the reverse direction during the 3-time flasher function operation.

HIGH FLASHER OPERATION

  • BCM detects the turn signal lamp circuit status from the current value.

  • BCM increases the turn signal lamp blinking speed if the lamp or harness open is detected with the turn signal lamp operating.

AUTO HAZARD FUNCTION

  • The air bag diagnosis sensor unit transmits a car crash information signal to the BCM via CAN communication, when the air bag diagnosis sensor unit detects strong impact to the Nissan Pathfinder vehicle body while ignition switch is ON.

  • When a car crash information signal from the air bag diagnosis sensor unit is detected, the BCM supplies voltage to each turn signal lamp and the hazard lamp blinks.

Parking, License Plate, Side Marker and Tail Lamp System

System Description

SYSTEM DIAGRAM

ComponentFunction
Front combination lamp Parking lamp LED headlamp control module supplies power supply to the parking lamp, and turns the parking lamp ON.
Front side marker lamp IPDM E/R supplies power supply to the front side marker lamp, and turns the front side marker lamp ON.
LED headlamp control module Refer to LED Headlamp Control Module.
Rear combination lamp (body side) Tail lamp IPDM E/R supplies power supply to the tail lamp, and turns the tail lamp ON.
Rear side marker lamp IPDM E/R supplies power supply to the rear side marker lamp, and turns the rear side marker lamp ON.
Rear combination lamp (back door side) Tail lamp IPDM E/R supplies power supply to the tail lamp, and turns the tail lamp ON.
License plate lamp IPDM E/R supplies power supply to the license plate lamp, and turns the license plate lamp ON.
IPDM E/R
  • Controls the integrated Smart FET, and supplies voltage to the load according to the request from the BCM via CAN communication.

  • Transmits the control signal and request to the LED headlamp control module via LIN communication according to the request from the BCM via CAN communication.

BCM
  • Detects each switch condition by the combination switch reading function.

  • Parking, license plate, side marker and tail lamp ON/OFF is judged from each signal, and then a request is transmitted to the IPDM E/R via CAN communication to turn each Smart FET ON/OFF.

  • It also transmits a status signal to the combination meter via CAN communication to turn the position lamp indicator lamp ON/OFF.

Combination meter Turns the position lamp indicator lamp ON/OFF according to the status from the BCM via CAN communication.
Intelligent Key unit Transmits the door lock/unlock request signal to the BCM via CAN communication from door lock/unlock button operation.
Combination switch Lighting and turn signal switch Inputs the each switch condition signal to the BCM.

OUTLINE

Parking, license plate, side marker and tail lamps are controlled by the combination switch reading function, parking, license plate, side marker and tail lamp control function of the BCM, and the Smart FET control function and LIN communication function of the IPDM E/R.

Signal transmission function list

Signal nameInputOutputDescription
Combination switch signal Combination switch BCM Transmits the combination switch signal to the BCM.
Door lock/unlock request signal Intelligent Key unit BCM (CAN) Transmits the door lock/unlock request signal via CAN communication.
Position light request signal BCM IPDM E/R (CAN) Transmits the position light request signal via CAN communication.
Position light status signal BCM Combination meter (CAN) Transmits position light status signal via CAN communication.

PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMPS OPERATION

  • BCM detects the combination switch (lighting and turn signal switch) condition by the combination switch reading function.

  • BCM transmits the position light request signal to the IPDM E/R and position light status signal to the combination meter via CAN communication according to the parking, license plate, side marker and tail lamps ON condition.

    Parking, license plate, side marker and tail lamp ON condition (when any of the following conditions are satisfied):

    • Lighting switch 1ST

    • Lighting switch 2ND

    • Lighting switch AUTO (only when the illumination judgement by auto light function is ON). Refer to System Description.

  • IPDM E/R turns the integrated Smart FET ON and turns the license plate, side marker and tail lamps ON according to the position light request signal.

  • IPDM E/R turns the integrated Smart FET ON according to position light request signal, and transmits the control signal to the LED headlamp control module.

  • IPDM E/R transmits the request signal to the LED headlamp control module via LIN communication according to the position light request signal.

  • LED headlamp control module turns the parking lamp ON according to the control signal and request from the IPDM E/R via LIN communication.

  • Combination meter turns the position lamp indicator lamp ON according to the position light status signal.

SIGNATURE LIGHT FUNCTION

Description

The signature light function is a function that turns ON the parking lamp, license plate lamp, side marker lamp and tail lamp for a set period of time when the doors are locked or unlocked from outside the Nissan Pathfinder vehicle.

Operation Description

BCM transmits the position light request signal to the IPDM E/R and position light status signal to the combination meter via CAN communication according to the signature light function ON condition.

Signature light function ON condition (operation when doors are unlocked):

  • When all of the following conditions are satisfied, the signature light function operates when door unlock operation is performed from outside the Nissan Pathfinder vehicle (Intelligent Key, door request switch, etc.):

    • Ignition switch: OFF

    • Door open/close status: All door close

    • Door lock status: All door lock

  • When any of the following conditions are satisfied while the signature light function is operating, the signature light function stops:

    • Ignition switch: ON

    • Since signature light function ON, approx. 30 seconds are passed.

Signature light function ON condition (operation when doors are locked):

  • When all of the following conditions are satisfied, the signature light function operates when door lock operation is performed from outside the Nissan Pathfinder vehicle (Intelligent Key or door request switch, etc.):

    • Ignition switch: OFF

    • Door open/close status: All door close

  • When any of the following conditions are satisfied while the signature light function is operating, the signature light function stops:

    • Ignition switch: ON

    • Since signature light function ON, approx. 15 seconds are passed.

Stop Lamp System

System Description

SYSTEM DIAGRAM

ComponentFunction
Rear combination lamp (body side) Stop lamp BCM supplies power supply to the stop lamp, and turns the stop lamp ON or blinks.
High-mounted stop lamp BCM supplies power supply to the high-mounted stop lamp, and turns the high-mounted stop lamp ON or blinks.
Stop lamp switch Refer to Stop Lamp Switch.
BCM Judges the Nissan Pathfinder vehicle status from each signal, and turns the stop lamp and high-mounted stop lamp ON or blinks.
ADAS control unit When the AEB system operates, a request is transmitted to the BCM via CAN communication to turn ON the stop lamp.

OUTLINE

Stop lamp and high-mounted stop lamp are controlled by the stop lamp switch reading function and the stop lamp and high-mounted stop lamp control function of the BCM, and the AEB (Automatic Emergency Braking) function of the ADAS control unit.

Signal transmission function list

Signal nameInputOutputDescription
Stop lamp switch signal Stop lamp switch BCM Transmits the stop lamp switch signal to the BCM.
Stop lamp request signal ADAS control unit BCM (CAN) Transmits the stop lamp request signal via CAN communication.

STOP LAMP AND HIGH-MOUNTED STOP LAMP OPERATION

  • BCM detects the brake pedal position status from the stop lamp switch.

  • BCM supplies voltage to stop lamp and high-mounted stop lamp according to the stop lamp and high-mounted stop lamp ON condition.

    Stop lamp and high-mounted stop lamp ON condition:

    • Brake pedal is depressed

AUTOMATIC EMERGENCY BRAKING FUNCTION

  • When the AEB system operates, the ADAS control unit transmits the stop lamp request signal to the BCM via CAN communication (for details about the AEB system, refer to System Description).

  • When the BCM receives the stop lamp request signal from the ADAS control unit, it supplies voltage to the stop lamp and high-mounted stop lamps, turning ON the stop lamp and high-mounted stop lamp.

Front Fog Lamp System

System Description

SYSTEM DIAGRAM

ComponentFunction
Front fog lamp IPDM E/R supplies power supply to the front fog lamp, and turns the front fog lamp ON.
IPDM E/R Controls the integrated Smart FET, and supplies voltage to the front fog lamp according to the request from the BCM via CAN communication.
BCM
  • Detects each switch condition by the combination switch reading function.

  • Front fog lamp ON/OFF is judged from each signal, and then a request is transmitted to the IPDM E/R via CAN communication to turn Smart FET ON/OFF.

  • It also transmits a status signal to the combination meter via CAN communication to turn the front fog lamp indicator lamp ON/OFF.

Combination meter Turns the front fog lamp indicator lamp ON/OFF according to the status signal from the BCM via CAN communication.
Combination switch Lighting and turn signal switch Inputs the each switch condition signal to the BCM.

OUTLINE

Front fog lamp is controlled by the combination switch reading function and front fog lamp control function of the BCM, and the Smart FET control function of the IPDM E/R.

Signal transmission function list

Signal nameInputOutputDescription
Combination switch signal Combination switch BCM Transmits the combination switch signal to the BCM.
Front fog light request signal BCM IPDM E/R (CAN) Transmits the front fog light signal via CAN communication.
Front fog light status signal BCM Combination meter (CAN) Transmits the front fog light status signal via CAN communication.

FRONT FOG LAMP OPERATION

  • BCM detects the combination switch (lighting and turn signal switch) condition by the combination switch reading function.

  • BCM transmits the front fog light request signal to the IPDM E/R and front fog light status signal to the combination meter via CAN communication according to the front fog lamp ON condition.

    Front fog lamp ON condition:

    • Front fog lamp switch ON, and any of the following conditions are satisfied:

      • Lighting switch 2ND

      • Lighting switch AUTO (only when the illumination judgement by auto light function is ON). Refer to System Description.

  • IPDM E/R turns the integrated Smart FET ON, and turns the front fog lamp ON according to the front fog light request signal.

  • Combination meter turns the front fog lamp indicator lamp ON according to the front fog light status signal.

Back-Up Lamp System

System Description

SYSTEM DIAGRAM

ComponentFunction
Rear combination lamp (back door side) Back-up lamp BCM controls to back-up lamp relay, and turns the back-up lamp ON.
Back-up lamp relay Supplies voltage to the back-up lamp with the control from the BCM.
BCM Controls the back-up lamp relay.

OUTLINE

Back-up lamp is controlled by the back-up lamp control function of the BCM.

BACK-UP LAMP OPERATION

  • BCM turns the back-up lamp relay ON, and turns the back-up lamp ON when the back-up lamp ON conditions are satisfied.

    Back-up lamp ON condition (when all of the following conditions are satisfied):

    • Engine running

    • Shift selector R range

Exterior Lamp Battery Saver System

System Description

SYSTEM DIAGRAM

ComponentFunction
IPDM E/R
  • Controls the integrated Smart FET, and supplies voltage to the load according with the request from the BCM via CAN communication.

  • Transmits the control signal and request to the LED headlamp control module via LIN communication according to the request from the BCM via CAN communication.

BCM
  • Detects each switch condition by the combination switch reading function.

  • Exterior lamp ON/OFF is judged from each signal, and then a request is transmitted to the IPDM E/R via CAN communication to control each lamp.

  • It also transmits a status signal to the combination meter via CAN communication to turn indicator lamps ON/OFF.

Combination meter Turns the indicator lamp ON/OFF or displays the indicator according to the status signal from the BCM via CAN communication.
Front door lock assembly LH (door switch) Detects the front door condition (open or closed), and transmits the door switch signal to the BCM.
Intelligent Key unit Transmits the door lock request signal to the BCM via CAN communication from door lock button operation.
ECM Transmits engine status signal to the BCM via CAN communication.
Combination switch Lighting and turn signal switch Inputs the each switch condition signal to the BCM.

OUTLINE

  • Exterior lamp battery saver system is controlled by the combination switch reading function and exterior lamp battery saver function of the BCM, and the Smart FET control function of the IPDM E/R.

  • BCM turns the exterior lamp* OFF, according to the Nissan Pathfinder vehicle status when ignition switch is placed OFF while the exterior lamp is ON, to prevent battery discharge.

*: Headlamp (LO/HI), front fog lamp, parking lamp, license plate lamp, side marker lamp and tail lamp

Signal transmission function list

Signal nameInputOutputDescription
Combination switch signal Combination switch BCM Transmits the combination switch signal to the BCM.
Door switch signal Front door lock assembly LH (door switch) BCM Transmits the door switch signal to the BCM.
Door lock request signal Intelligent Key unit BCM (CAN) Transmits the door lock request signal via CAN communication.
Engine status signal ECM BCM (CAN) Transmits the engine status signal via CAN communication.
High beam request signal BCM IPDM E/R (CAN) Transmits the high beam request signal via CAN communication.
Low beam request signal BCM IPDM E/R (CAN) Transmits the low beam request signal via CAN communication.
Position light request signal BCM IPDM E/R (CAN) Transmits the position light request signal via CAN communication.
Front fog light request signal BCM IPDM E/R (CAN) Transmits the front fog light request signal via CAN communication.
High beam status signal BCM Combination meter (CAN) Transmits the high beam status signal via CAN communication.
Low beam status signal BCM Combination meter (CAN) Transmits the low beam status signal via CAN communication.
Position light status signal BCM Combination meter (CAN) Transmits the position light status signal via CAN communication.
Front fog light status signal BCM Combination meter (CAN) Transmits the front fog light status signal via CAN communication.

EXTERIOR LAMP BATTERY SAVER ACTIVATION

  • BCM turns the exterior lamps OFF (battery saver is activated) when the exterior lamp ON, engine status is running to stop (ignition switch OFF) and any of the following conditions are satisfied:

    • After 60 seconds passed

    • Front door LH is moved from CLOSED to OPEN [door switch OFF to ON]

    • Door lock operation (operate with Intelligent Key, door request switch etc.)

  • When in any of the following conditions are satisfied (after the exterior lamp battery saver is activated), exterior lamps can be turned ON:

    • Ignition switch is placed from OFF => Other than OFF

    • Lighting switch is changed

    • Front fog lamp switch is changed

Light Reminder Warning System

System Description

SYSTEM DIAGRAM

Signal transmission function list

Signal nameInputOutputDescription
Combination switch signal Combination switch BCM Transmits the combination switch signal to the BCM.
Engine status signal ECM BCM (CAN) Transmits the engine status signal via CAN communication.
Door switch signal Front door lock assembly (door switch) BCM Transmits the door switch signal to the BCM.
Light reminder warning signal BCM Combination meter (CAN) Transmits the light reminder warning signal via CAN communication.

DESIGN/PURPOSE

When the driver is exiting the vehicle while engine status is other than running and lamps are ON, the light reminder warning displays a warning in the information display to alert the driver.

Full TFT Meter
SymbolMessage

Reminder

Turn OFF

Headlights
7 inch Information Display
SymbolMessage

Reminder

Turn OFF

Headlights

SYNCHRONIZATION WITH MASTER WARNING LAMP

Not applicable

SYNCHRONIZATION WITH WARNING CHIME

Synchronization is applied.

For warning chime. Refer to System Description.

OPERATION AT COMBINATION METER CAN COMMUNICATION CUT-OFF OR UNUSUAL SIGNAL

For actions on CAN communications blackout in the combination meter, refer to Fail-Safe (full TFT meter) or Fail-Safe (7 inch information display).

SIGNAL PATH

  • BCM reads the status of the combination switch (lighting and turn signal switch).

  • BCM detects the Nissan Pathfinder vehicle condition depending on the engine status signal received by the ECM via CAN communication.

  • BCM judges the light reminder warning using the lighting switch signal, front door lock assembly LH (door switch) signal and engine status signal. BCM transmits the light reminder warning signal to the combination meter via CAN communication.

  • When the combination meter receives the light reminder warning signal, the light reminder warning pop-up screen appears in the information display.

When all of the following conditions are satisfied:

  • Engine status is other than running

  • Lighting switch 1ST or 2ND

  • Front door LH OPEN [front door lock assembly (door switch) ON]

When any of the following conditions are satisfied:

  • Engine status is running

  • Lighting switch other than 1ST or 2ND

  • Front door LH CLOSE [front door lock assembly (door switch) OFF]

TIMING CHART

Headlamp Warning System

System Description

SYSTEM DIAGRAM

Signal transmission function list

Signal nameInputOutputDescription
Headlamp warning signal LED headlamp control module Combination meter (CAN) Inputs the headlamp warning signal via LIN communication, and transmits it via CAN communication.

DESIGN/PURPOSE

Headlamp warning warns the driver that there is a malfunction in the LED headlamp system.

  • Headlight

    System Error

    See Owner′s Manual

SYNCHRONIZATION WITH MASTER WARNING LAMP

Synchronization is applied.

OPERATION AT COMBINATION METER CAN COMMUNICATION CUT-OFF OR UNUSUAL SIGNAL

For actions on CAN communications blackout in the combination meter, refer to Fail-Safe (full TFT meter) or Fail-Safe (7 inch information display).

SIGNAL PATH

  • When the LED headlamp control module detects a malfunction of the headlamp (LO) circuit, the headlamp warning signal is transmitted to the IPDM E/R via LIN communication.

  • When the IPDM E/R receives the headlamp warning signal via LIN communication or the IPDM E/R detects a malfunction of LIN communication, the IPDM E/R transmits the headlamp warning signal to the combination meter via CAN communication.

  • When the ignition switch is ON and the combination meter receives the headlamp warning signal from the IPDM E/R via CAN communication, the combination meter displays the headlamp warning on the information display.

When all of the following conditions are satisfied:

  • Ignition switch ON

  • Headlamp warning signal via CAN communication is ON

When any of the following conditions are satisfied:

  • Ignition switch other than ON

  • Headlamp warning signal via CAN communication is OFF

TIMING CHART

Trailer Tow System

System Description

SYSTEM DIAGRAM

Signal transmission function list

Signal nameInputOutputDescription
Combination switch signal Combination switch BCM Transmits the combination switch signal to the BCM.
Tail lamp request signal BCM IPDM E/R (CAN) Transmits the tail lamp request signal via CAN communication.
Stop lamp switch signal Stop lamp switch Electric brake pre-wiring Transmits the stop lamp switch signal to the electric brake pre-wiring.

TRAILER TAIL LAMP OPERATION

The trailer tail lamps are controlled by the trailer tow relay-1. With the combination switch (lighting and turn signal switch) in the 1ST position, the BCM detects lighting switch 1ST. The BCM sends a tail lamp request signal to the IPDM E/R via CAN communication. The IPDM E/R then turns the integrated Smart FET ON and turns the trailer tow relay-1 ON according to the tail lamp request signal.

TRAILER TURN SIGNAL LAMP OPERATION

The trailer turn signal lamps are controlled by the BCM. When the combination switch (lighting and turn signal switch) is in the LH or RH position with the ignition switch ON, the combination switch (lighting and turn signal switch) sends a signal to the BCM. The BCM detects the TURN RH or TURN LH ON request. The BCM sends a control signal to the respective trailer turn relay which sends power to the trailer receptacle.

TRAILER HAZARD LAMP OPERATION

The trailer hazard lamps are controlled by the BCM. When the hazard switch is pressed, the BCM detects the hazard ON request. The BCM then sends a control signal to both trailer turn relays which sends power to the trailer receptacle.

TRAILER BRAKE LAMP OPERATION

The trailer brake lamps operate when the brake pedal is pressed sending the stop lamp switch signal to the trailer receptacle.

TRAILER BACK-UP LAMP OPERATION

The trailer back-up lamps are controlled by the trailer back-up relay. When the shift selector is in R with the ignition switch ON, the back-up lamp relay supplies power to the trailer back-up relay which sends power to the trailer receptacle.

Diagnosis System (bcm) Nissan Pathfinder Fifth generation

Common Item

CONSULT Function (BCM - COMMON ITEM)

BCM Refer to CONSULT Function (BCM - COMMON ITEM).

Head Lamp

CONSULT Function (BCM - HEAD LAMP)

BCM Refer to CONSULT Function (BCM - HEAD LAMP).

Flasher

CONSULT Function (BCM - FLASHER)

BCM Refer to CONSULT FUnction (BCM - FLASHER).

Comb Sw

CONSULT Function (BCM - COMB SW)

BCM Refer to CONSULT Function (BCM - COMB SW).

Battery Saver

CONSULT Function (BCM - BATTERY SAVER)

BCM Refer to CONSULT Function (BCM - BATTERY SAVER).

Diagnosis System (ipdm E/r) Nissan Pathfinder 5th Gen

CONSULT Function (IPDM E/R)

IPDM E/R Refer to CONSULT Function (IPDM E/R).