Dtc/circuit Diagnosis (Ignition Signal ... Variable Induction Air System)

In this manual: Dtc/circuit Diagnosis (Ignition Signal ... Variable Induction Air System)
General Information — 8Engine :: Engine Mechanical — 19Engine Lubrication System - Precautions. Preparation — 1Engine Lubrication System - Lubrication System (System Description). Engine Oil Pressure (Basic Inspection). Service Data and Specifications (SDS) — 1Engine Cooling System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Engine Cooling System - Engine Coolant — 1Engine Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Engine Control System - Ecu Diagnosis Information — 1Ecu Diagnosis Information - Ecm ++ — 1Engine Control System - Basic Inspection — 1Basic Inspection - Diagnosis and Repair Workflow ++ — 1Basic Inspection - Basic Inspection ++ — 1Basic Inspection - Additional Service When Replacing Ecm ++ — 1Basic Inspection - Fuel Pressure Check ++ — 1Basic Inspection - How to Set Srt Code ++ — 1Basic Inspection - How to Erase Permanent Dtc ++ — 1Engine Control System - Dtc/circuit Diagnosis — 1Engine Control System - Symptom Diagnosis — 1Engine Control System - Periodic Maintenance — 1Engine Control System - Removal and Installation — 1Fuel System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Fuel System - Fuel System (Periodic Maintenance). Fuel Level Sensor Unit (Disassembly and Assembly) — 1Exhaust System - Precautions. Preparation — 1Exhaust System - Exhaust System (Periodic Maintenance). Exhaust System (Removal and Installation) — 1Starting System - Precautions. Preparation. Starter Motor (Service Data and Specifications (sds)) — 1Starting System - Diagnosis and Repair Work Flow — 1Starting System - Starting System (Symptom Diagnosis). Starter Motor (Removal and Installation) — 1Accelerator Control System - Precautions. Service Data and Specifications (SDS) — 1Accelerator Control System - Accelerator Pedal Assembly — 1Transmission & Driveline :: Transaxle & Transmission — 21Driveline - System Description — 1Transfer: Ty92b - Ecu Diagnosis Information. Awd Control Unit ++ — 1Driveline - Basic Inspection — 1Driveline - Dtc/circuit Diagnosis — 1Driveline - Symptom Diagnosis — 1Driveline - Removal and Installation — 1Transfer: Ty92b - Unit Removal and Installation. Transfer Assembly ++ — 1Driveline - Unit Disassembly and Assembly — 1Driveline - Basic Inspection — 1Driveline - Removal and Installation — 1Driveline - Unit Disassembly and Assembly — 1Front Axle - Precautions. Preparation — 1Front Axle - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Front Axle - Front Drive Shaft Boot — 1Front Axle - Front Drive Shaft — 1Rear Axle - Precautions. Preparation. Service Data and Specifications (SDS) — 1Rear Axle - Noise, Vibration and Harshness (nvh) Troubleshooting — 1Rear Axle - Rear Drive Shaft — 1Suspension :: Front Suspension — 7Rear Suspension - Precautions. Preparation — 1Rear Suspension - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Rear Suspension - Rear Suspension Assembly — 1Road Wheels & Tires - Precautions — 1Road Wheels & Tires - Preparation. Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Road Wheels & Tires - System — 1Brakes :: Brake System — 9Parking Brake System - Precautions. Preparation — 1Parking Brake System - System — 1Vdc/tcs/abs - Precautions ++ — 1Brake Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Dtc/circuit Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Steering :: Steering System — 9Steering Control System - Precautions — 1Steering Control System - System — 1Steering Control System - Eps Control Unit (Ecu Diagnosis Information. Removal and Installation) — 1Restraints :: Seat Belt — 7Srs Air Bag - Precautions. Preparation — 1Srs Air Bag - Collision Diagnosis — 1Srs Air Bag - Occupant Classification System — 1Srs Air Bag Control System - Precautions — 1Srs Air Bag Control System - System — 1Srs Air Bag Control System - Diagnosis Sensor Unit — 1Srs Air Bag Control System - Inspection and Adjustment — 1Ventilation, Heater & Air Conditioner :: Ventilation System — 6Heater & Air Conditioning System - Precautions — 1Heater & Air Conditioning System - Preparation — 1Heater & Air Conditioning System - Component Parts — 1Heater & Air Conditioning System - Diagnosis and Repair Work Flow — 1Heater & Air Conditioning System - Compressor — 1Heater & Air Conditioning System - Cooler Pipe and Hose — 1Heater & Air Conditioning System - Condenser. Condenser — 1Heater & Air Conditioning System - Heating and Cooling Unit Assembly — 1Heater & Air Conditioning System - Service Data and Specifications (SDS) — 1Heater & Air Conditioning Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1Heater & Air Conditioning Control System - Ecu Diagnosis Information — 1Heater & Air Conditioning Control System - Basic Inspection — 1Heater & Air Conditioning Control System - Dtc/circuit Diagnosis — 1Heater & Air Conditioning Control System - Symptom Diagnosis — 1Heater & Air Conditioning Control System - Removal and Installation — 1Body Interior :: Interior — 8Instrument Panel - Precautions. Preparation. Clip List — 1Instrument Panel - Squeak and Rattle Trouble Diagnoses — 1Instrument Panel - Cluster Lid C — 1Seat - Precautions — 1Seat - Preparation. Clip List — 1Seat - Component Parts — 1Seat - System — 1Seat - Diagnosis and Repair Work Flow — 1Seat - Front Seat — 1Seat - Second Row Seats — 1Seat - Third Row Seats — 1Seat - Front Seat — 1Seat - Second Row Seat — 1Seat - Third Row Seat — 1Automatic Drive Positioner - Precautions. Preparation — 1Automatic Drive Positioner - System — 1Automatic Drive Positioner - Diagnosis and Repair Work Flow — 1Automatic Drive Positioner - Inspection and Adjustment — 1Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock — 38Security Control System - Precautions — 1Security Control System - System — 1Security Control System - Ecm, Bcm, Intelligent Key Unit, Ipdm E/r — 1Security Control System - Vehicle Security System Cannot Be Set — 1Glass & Window System - Precautions. Preparation — 1Glass & Window System - Squeak and Rattle Trouble Diagnoses — 1Power Window Control System - Precautions. Preparation — 1Power Window Control System - Power Supply and Ground Circuit — 1Power Window Control System - Power Window Motor Circuit — 1Power Window Control System - Front Power Window Rh Alone Does Not Operate — 1Power Window Control System - Rear Lh Side Power Window Alone Does Not Operate — 1Power Window Control System - Rear Rh Side Power Window Alone Does Not Operate — 1Roof - Precautions. Preparation — 1Roof - Power Supply and Ground Circuit — 1Roof - Moonroof Switch Assembly — 1Roof - Lin Communication Circuit — 1Roof - Auto Operation Does Not Operate — 1Roof - Anti-Pinch Function Does Not Operate — 1Exterior - Precautions. Preparation. Clip List (Preparation) — 1Exterior - Squeak and Rattle Trouble Diagnoses — 1Exterior - Fender Protector — 1Exterior - Over Fender — 1Exterior - Under Cover — 1Exterior - Roof Side Rail — 1Body Repair - Service Information — 1Service Information - Sheet Metal Work ++ — 1Service Information - Body Welding and Precautions ++ — 1Service Information - Safety and Health ++ — 1Service Information - Repairing Procedures and Precautions ++ — 1Body Repair - Precaution — 1Body Repair - Preparation — 1Body Repair - Removal and Installation — 1Driver Controls :: Mirrors — 8Exterior Lighting System - System Description — 1System Description - Component Parts ++ — 1Exterior Lighting System - Basic Inspection — 1Exterior Lighting System - Dtc/circuit Diagnosis — 1Exterior Lighting System - Symptom Diagnosis — 1Exterior Lighting System - Periodic Maintenance — 1Exterior Lighting System - Removal and Installation — 1Interior Lighting System - Precautions. Preparation — 1Interior Lighting System - Component Parts. Interior Lighting System — 1Interior Lighting System - System — 1Interior Lighting System - Diagnosis and Repair Work Flow — 1Interior Lighting System - Interior Lighting System Symptoms (Symptom Diagnosis). Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Interior Lighting System - Foot Lamp — 1Wiper & Washer - Precautions — 1Wiper & Washer - Preparation. Bcm, Ipdm E/r (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Wiper & Washer - System — 1Wiper & Washer - Diagnosis and Repair Work Flow — 1Defogger - Precautions. Bcm, A/c Auto Amp. (Ecu Diagnosis Information) — 1Defogger - Diagnosis and Repair Work Flow — 1Horn - Precautions — 1Electrical & Power Control :: Power Outlet — 13Body Control System - Precautions. Preparation — 1Body Control System - Component Parts — 1Body Control System - System — 1Body Control System - Diagnosis System (bcm) — 1Body Control System - Bcm — 1Lan System - System Description — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - Removal and Installation — 1Charging System - Precautions. Preparation. Ecm, Ipdm E/r (Ecu Diagnosis Information) — 1Charging System - Diagnosis and Repair Work Flow — 1Charging System - Charging System (Symptom Diagnosis). Generator (Removal and Installation). Service Data and Specifications (SDS) — 1Power Supply, Ground & Circuit Elements - Precautions. Preparation. Service Data and Specifications (SDS) — 1Driver Information & Multimedia :: Meter, Warning Lamp & Indicator — 25Warning Chime System - Application Notice (How to Use This Manual). Precautions — 1Warning Chime System - System — 1Warning Chime System - Diagnosis System (combination Meter) — 1Warning Chime System - Bcm, Combination Meter (Ecu Diagnosis Information). Diagnosis and Repair Work Flow (Basic Inspection) — 1Sonar System - Precautions. Preparation — 1Sonar System - Sonar Control Unit — 1Dtc/circuit Diagnosis - B2720 Corner Sensor [rl] ++ — 1Audio, Visual & Navigation System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Multi Av (av Control Unit) ++ — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Symptom Diagnosis - Multi Av System ++ — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Cruise Control & Driver Assistance :: Cruise Control System — 17Driver Assistance System - System Description — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Driver Assistance System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1System Description - Handling Precaution ++ — 1Driver Assistance System - Ecu Diagnosis Information — 1Driver Assistance System - Basic Inspection — 1Basic Inspection - Distance Sensor Alignment ++ — 1Basic Inspection - Camera Aiming Adjustment ++ — 1Basic Inspection - Action Test ++ — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Laser/radar (distance Sensor) ++ — 1Dtc/circuit Diagnosis - Lane Camera (front Camera Unit) ++ — 1Driver Assistance System - Symptom Diagnosis — 1Driver Assistance System - Removal and Installation — 1Driver Assistance System - System Description — 1System Description - System ++ — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Drive Mode System - Precautions — 1Drive Mode System - Component Parts. Drive Mode System — 1Drive Mode System - System — 1Drive Mode System - Diagnosis and Repair Work Flow — 1Drive Mode System - Drive Mode Select Switch Circuit — 1Maintenance - Precautions. Preparation — 1Maintenance - General Maintenance — 1Maintenance - Periodic Maintenance — 1Maintenance - Recommended Fluids and Lubricants — 1Maintenance - Engine Maintenance — 1Maintenance - Chassis and Body Maintenance — 1Engine Lubrication System - Periodic Maintenance — 1Engine Lubrication System - Removal and Installation — 1Engine Cooling System - System Description — 1Engine Cooling System - Removal and Installation — 1Engine Control System - Vq35dd — 1Fuel System - Removal and Installation — 1Starting System - System Description — 1Starting System - Dtc/circuit Diagnosis — 1Driveline - Transfer: Ty92b — 1Driveline - Rear Propeller Shaft: 3fcj-Cvj — 1Driveline - Rear Final Drive: R145 — 1Front Axle - Periodic Maintenance — 1Front Axle - Removal and Installation — 1Rear Axle - Periodic Maintenance — 1Rear Axle - Removal and Installation — 1Rear Suspension - Removal and Installation — 1Road Wheels & Tires - System Description — 1Road Wheels & Tires - Basic Inspection — 1Road Wheels & Tires - Dtc/circuit Diagnosis — 1Road Wheels & Tires - Symptom Diagnosis — 1Road Wheels & Tires - Periodic Maintenance — 1Road Wheels & Tires - Removal and Installation — 1Parking Brake System - System Description — 1Parking Brake System - Basic Inspection — 1Parking Brake System - Dtc/circuit Diagnosis — 1Parking Brake System - Symptom Diagnosis — 1Parking Brake System - Removal and Installation — 1Brake Control System - Vdc/tcs/abs — 1Brake Control System - Automatic Brake Hold — 1Brake Control System - Automatic Emergency Braking — 1Brake Control System - Rear Automatic Braking — 1Steering Control System - System Description — 1Steering Control System - Basic Inspection — 1Steering Control System - Dtc/circuit Diagnosis — 1Steering Control System - Symptom Diagnosis — 1Srs Air Bag - Removal and Installation — 1Srs Air Bag Control System - System Description — 1Srs Air Bag Control System - Basic Inspection — 1Srs Air Bag Control System - Symptom Diagnosis — 1Heater & Air Conditioning System - Symptom Diagnosis — 1Heater & Air Conditioning System - Periodic Maintenance — 1Heater & Air Conditioning Control System - Automatic Air Conditioning — 1Instrument Panel - Removal and Installation — 1Instrument Panel - Unit Disassembly and Assembly — 1Seat - Ecu Diagnosis Information — 1Seat - Dtc/circuit Diagnosis — 1Seat - Symptom Diagnosis — 1Automatic Drive Positioner - System Description — 1Automatic Drive Positioner - Ecu Diagnosis Information — 1Automatic Drive Positioner - Dtc/circuit Diagnosis — 1Automatic Drive Positioner - Symptom Diagnosis — 1Automatic Drive Positioner - Removal and Installation — 1Security Control System - System Description — 1Security Control System - Basic Inspection — 1Security Control System - Dtc/circuit Diagnosis — 1Security Control System - Symptom Diagnosis — 1Security Control System - Removal and Installation — 1Glass & Window System - Removal and Installation — 1Power Window Control System - System Description — 1Power Window Control System - Ecu Diagnosis Information — 1Power Window Control System - Basic Inspection — 1Power Window Control System - Dtc/circuit Diagnosis — 1Power Window Control System - Symptom Diagnosis — 1Power Window Control System - Removal and Installation — 1Roof - System Description — 1Roof - Ecu Diagnosis Information — 1Roof - Basic Inspection — 1Roof - Dtc/circuit Diagnosis — 1Roof - Symptom Diagnosis — 1Roof - Removal and Installation — 1Exterior - System Description — 1Exterior - Removal and Installation — 1Body Repair - Repair Information — 1Exterior Lighting System - Led Headlamp — 1Interior Lighting System - Dtc/circuit Diagnosis — 1Interior Lighting System - Removal and Installation — 1Wiper & Washer - System Description — 1Wiper & Washer - Dtc/circuit Diagnosis — 1Wiper & Washer - Symptom Diagnosis — 1Wiper & Washer - Removal and Installation — 1Defogger - System Description — 1Defogger - Dtc/circuit Diagnosis — 1Defogger - Symptom Diagnosis — 1Defogger - Removal and Installation — 1Horn - Removal and Installation — 1Body Control System - Basic Inspection — 1Body Control System - Dtc/circuit Diagnosis — 1Body Control System - Symptom Diagnosis — 1Body Control System - Removal and Installation — 1Lan System - Can Fundamental — 1Lan System - Can — 1Lan System - Can Gateway — 1Power Control System - Ipdm E/r — 1Power Control System - Power Distribution System — 1Charging System - System Description — 1Charging System - Dtc/circuit Diagnosis — 1Power Supply, Ground & Circuit Elements - System Description — 1Power Supply, Ground & Circuit Elements - Basic Inspection — 1Power Supply, Ground & Circuit Elements - Removal and Installation — 1Warning Chime System - System Description — 1Warning Chime System - Dtc/circuit Diagnosis — 1Warning Chime System - Symptom Diagnosis — 1Sonar System - System Description — 1Sonar System - Basic Inspection — 1Sonar System - Dtc/circuit Diagnosis — 1Sonar System - Symptom Diagnosis — 1Sonar System - Removal and Installation — 1Audio, Visual & Navigation System - Nissanconnect — 1Audio, Visual & Navigation System - Intelligent Around View Monitor System — 1Audio, Visual & Navigation System - Rear View Monitor System — 1Audio, Visual & Navigation System - Telematics System — 1Driver Assistance System - Adas Control Unit 2 — 1Driver Assistance System - Driver Assistance System — 1Driver Assistance System - Chassis Control — 1Drive Mode System - Removal and Installation — 1Dtc/circuit Diagnosis (C053c Wheel Speed Sensor ... U2141 Can Comm Circuit) — 1Dtc/circuit Diagnosis (P0011 Intake Valve Timing Control ... P0111 Iat Sensor) — 1Dtc/circuit Diagnosis (P0116 Engine Coolant Temperature Sensor ... P025b Fuel Pump Module a) — 1Dtc/circuit Diagnosis (P026b Injection Timing ... P0420 Three Way Catalyst Function) — 1Dtc/circuit Diagnosis (P0441 Evap Control System ... P0524 Engine Oil Pressure) — 1Dtc/circuit Diagnosis (P0532 A/c Refrigerant Pressure Sensor ... P064d Ecm) — 1Dtc/circuit Diagnosis (P06da Engine Oil Pressure Control Solenoid Valve ... P1217 Engine Over Temperature) — 1Dtc/circuit Diagnosis (P1220 Fuel Pump Control Module (fpcm) ... P1574 Ascd Vehicle Speed Sensor) — 1Dtc/circuit Diagnosis (P1575 Brake Switch ... P2101 Electric Throttle Control Function) — 1Dtc/circuit Diagnosis (P2118 Throttle Control Motor ... P34ac Electric Intake Valve Timing Control Actuator) — 1Dtc/circuit Diagnosis (Active Grille Shutter ... High Pressure Fuel Pump) — 1Dtc/circuit Diagnosis (Ignition Signal ... Variable Induction Air System) — 14012 C1040 Emergency Brake — 14013 C106a Wheel Sensor — 14014 C1078-55 Not Configuration — 14015 C10b4-98 Overheat — 14016 B1001 Lap Pre-Tensioner Lh — 14017 B0001 Driver Air Bag Module — 14018 B100e Knee Air Bag Module Rh — 14019 B142x Collision Detection — 1Dtc/circuit Diagnosis (B20c7-11 A/c Clutch ... B24a6-11 in-Vehicle Sensor) — 1Dtc/circuit Diagnosis (B24a6-15 in-Vehicle Sensor ... U2140-87 Can Comm Err (ecm)) — 1Dtc/circuit Diagnosis (C1f00-1c Control Unit ... C1f04-61 Brake Sw/stop Lamp Sw) — 1Dtc/circuit Diagnosis (C1f05-49 Front Camera Unit ... C1f70-87 Ethernet Circuit) — 1
166steps
~996min
5/5difficulty
Done 0 of 166
  • Ignition Signal
  • Information Display (ascd)
  • Malfunction Indicator Lamp
  • Mass Air Flow Sensor
  • On Board Refueling Vapor Recovery (orvr)
  • Refrigerant Pressure Sensor
  • Sensor Power Supply 2 Circuit
  • Variable Induction Air System

Ignition Signal Nissan Pathfinder 2026

Component Function Check

INSPECTION START

Turn ignition switch OFF, and restart engine.

Does the engine start?

YES-1>>

With CONSULT: GO TO 2.

YES-2>>

Without CONSULT: GO TO 3.

No>>

Proceed to Diagnosis Procedure.

CHECK IGNITION SIGNAL FUNCTION

With CONSULT

  1. Perform “POWER BALANCE” in “Active Test” mode of “ENGINE”.

  2. Make sure that each circuit produces a momentary engine speed drop.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Proceed to Diagnosis Procedure.

CHECK IGNITION SIGNAL FUNCTION

Without CONSULT

  1. Let engine idle.

  2. Read the voltage signal between ECM harness connector terminals under the following conditions with an oscilloscope.

    ECM Condition Voltage signal
    + –
    Connector Terminal Connector Terminal
    F79 153 E32 204

    [Engine is running]

    • Warm-up condition

    • Idle speed

    154
    161
    162
    164
    168

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Proceed to Diagnosis Procedure.

Diagnosis Procedure

CHECK FUSE-I

  1. Turn ignition switch OFF.

  2. Check that the following fuse is not blowing.

    Location Fuse No. Capacity
    IPDM E/R #81 15A

Is the fuse blown (open)?

YES>>

Replace the fuse after repairing the applicable circuit.

NO>>

GO TO 2.

CHECK IGNITION COIL POWER SUPPLY-I

  1. Turn ignition switch OFF, wait at least 10 seconds and then turn it ON.

  2. Check the voltage between ECM harness connector terminals as per the following.

    ECM Voltage
    Connector + –
    Terminal
    E32 185 204 Battery voltage

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Perform the trouble diagnosis for ECM power supply circuit. Refer to Diagnosis Procedure.

CHECK IGNITION COIL POWER SUPPLY-II

  1. Turn ignition switch OFF.

  2. Disconnect condenser harness connector.

  3. Turn ignition switch ON.

  4. Check the voltage between condenser harness connector and ground.

    + − Voltage
    Condenser
    Connector Terminal
    F21 1 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

GO TO 4.

CHECK IGNITION COIL POWER SUPPLY CIRCUIT-I

  1. Turn ignition switch OFF.

  2. Disconnect IPDM E/R harness connector.

  3. Check the continuity between IPDM E/R harness connector and condenser harness connector.

    IPDM E/R Condenser Continuity
    Connector Terminal Connector Terminal
    E121 43 F21 1 Existed
  4. Also check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

Proceed to Intermittent Incident.

NO>>

Repair or replace error-detected parts.

CHECK CONDENSER GROUND CIRCUIT FOR OPEN AND SHORT

  1. Turn ignition switch OFF.

  2. Check the continuity between condenser harness connector and ground.

    Condenser — Continuity
    Connector Terminal
    F21 2 Ground Existed
  3. Also check harness for short to power.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace error-detected parts.

CHECK CONDENSER

Refer to Component Inspection (Condenser)

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Replace condenser.

CHECK IGNITION COIL POWER SUPPLY-III

  1. Reconnect all harness connectors disconnected.

  2. Disconnect ignition coil harness connector.

  3. Turn ignition switch ON.

  4. Check the voltage between ignition coil harness connector and ground.

    + − Voltage
    Ignition coil
    Cylinder Connector Terminal
    1 F47 3 Ground Battery voltage
    2 F8 3
    3 F48 3
    4 F9 3
    5 F49 3
    6 F10 3

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

GO TO 8.

CHECK IGNITION COIL POWER SUPPLY CIRCUIT-II

  1. Turn ignition switch OFF.

  2. Disconnect IPDM E/R harness connector.

  3. Check the continuity between IPDM E/R harness connector and ignition coil harness connector.

    IPDM E/R Ignition coil Continuity
    Connector Terminal Cylinder Connector Terminal
    E121 43 1 F47 3 Existed
    2 F8 3
    3 F48 3
    4 F9 3
    5 F49 3
    6 F10 3
  4. Also check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

Proceed to Intermittent Incident.

NO>>

Repair or replace error-detected parts.

CHECK IGNITION COIL GROUND CIRCUIT

  1. Turn ignition switch OFF.

  2. Check the continuity between ignition coil harness connector and ground.

    Ignition coil — Continuity
    Cylinder Connector Terminal
    1 F47 2 Ground Existed
    2 F8 2
    3 F48 2
    4 F9 2
    5 F49 2
    6 F10 2
  3. Also check harness for short to power.

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair or replace error-detected parts.

CHECK IGNITION COIL OUTPUT SIGNAL CIRCUIT

  1. Disconnect ECM harness connector.

  2. Check the continuity between ignition coil harness connector and ECM harness connector.

    Ignition coil ECM Continuity
    Cylinder Connector Terminal Connector Terminal
    1 F47 1 F79 161 Existed
    2 F8 1 164
    3 F48 1 153
    4 F9 1 162
    5 F49 1 168
    6 F10 1 154
  3. Also check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

GO TO 11.

NO>>

Repair or replace error-detected parts.

CHECK IGNITION COIL WITH POWER TRANSISTOR

Refer to Component Inspection (Ignition Coil with Power Transistor).

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace malfunctioning ignition coil with power transistor. Refer to Removal and Installation (Bank 2) or Removal and Installation (Bank 1).

Component Inspection (Ignition Coil with Power Transistor)

CHECK IGNITION COIL WITH POWER TRANSISTOR-I

  1. Turn ignition switch OFF.

  2. Disconnect ignition coil harness connector.

  3. Check resistance between ignition coil terminals as per the following.

    Ignition coil Condition Resistance
    Terminal
    1 2 Temperature [°C (°F)] 25 (77) Except 0 or ∞Ω
    1 3 Except 0 Ω
    2 3

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace malfunctioning ignition coil with power transistor. Refer to Removal and Installation (Bank 2) or Removal and Installation (Bank 1).

CHECK IGNITION COIL WITH POWER TRANSISTOR-II

  1. Turn ignition switch OFF.

  2. Reconnect all harness connectors disconnected.

  3. Pull out 20A fuse (No.85) from IPDM E/R to release fuel pressure. Refer to IPDM E/R Terminal Arrangement .

  4. Start engine.

  5. After engine stalls, crank it two or three times to release all fuel pressure.

  6. Turn ignition switch OFF.

  7. Remove all ignition coil harness connectors to avoid the electrical discharge from the ignition coils.

  8. Remove ignition coil and spark plug of the cylinder to be checked.

  9. Crank engine for 5 seconds or more to remove combustion gas in the cylinder.

  10. Connect spark plug and harness connector to ignition coil.

  11. Fix ignition coil using a rope etc. with gap of 13 – 17 mm (0.52 – 0.66 in) between the edge of the spark plug and grounded metal portion as shown in the figure.

  12. Crank engine for about three seconds, and check whether spark is generated between the spark plug and the grounded metal portion.

    Spark should be generated.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace malfunctioning ignition coil with power transistor. Refer to Removal and Installation (Bank 2) or Removal and Installation (Bank 1).

Component Inspection (Condenser)

CHECK CONDENSER

  1. Turn ignition switch OFF.

  2. Disconnect condenser harness connector.

  3. Check resistance between condenser terminals as per the following.

    Condenser Condition Resistance
    Terminal
    1 2 Temperature [°C (°F)] 25 (77) Above 1 MΩ

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace condenser.

Information Display (ascd) Nissan Pathfinder R53

Component Function Check

CHECK INFORMATION DISPLAY

  1. Start engine.

  2. Press MAIN switch on ASCD steering switch.

  3. Drive the Nissan Pathfinder vehicle at more than 40 km/h.

  4. Press COAST/SET switch.

  5. Check that the reading of the speedometer shows the same value as the set speed indicated in the information display while driving the Nissan Pathfinder vehicle on a flat road.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Proceed to Diagnosis Procedure.

Diagnosis Procedure

CHECK DTC

Check that DTC UXXXX, P0500 or P1574 is not displayed.

Is the inspection result normal?

YES>>

GO TO 2.

NO-1>>

Perform trouble diagnosis for DTC UXXXX. Refer to DTC Index.

NO-2>>

Perform trouble diagnosis for DTC P0500. Refer to DTC Description.

NO-3>>

Perform trouble diagnosis for DTC P1574. Refer to DTC Description.

CHECK DTC WITH COMBINATION METER

  • FULL TFT METER: Refer to CONSULT Function (METER/M&A).

  • 7 INCH INFORMATION DISPLAY: Refer to CONSULT Function (METER/M&A).

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Perform trouble diagnosis for DTC indicated.

CHECK INTERMITTENT INCIDENT

Refer to Intermittent Incident.

Is the inspection result normal?

YES>>

Replace combination meter.

  • FULL TFT METER: Refer to Removal and Installation.

  • 7 INCH INFORMATION DISPLAY: Refer to Removal and Installation.

NO>>

Repair or replace.

Malfunction Indicator Lamp Nissan Pathfinder 2026

Component Function Check

CHECK MIL FUNCTION

  1. Turn ignition switch ON.

  2. Make sure that MIL illuminates.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Proceed to Diagnosis Procedure.

Diagnosis Procedure

CHECK DTC

Check that DTC UXXXX is not displayed.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Perform trouble diagnosis for DTC UXXXX.

CHECK DTC WITH COMBINATION METER

Check DTC with combination meter.

  • FULL TFT METER: Refer to CONSULT Function (METER/M&A).

  • 7 INCH INFORMATION DISPLAY: Refer to CONSULT Function (METER/M&A).

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace.

CHECK INTERMITTENT INCIDENT

Refer to Intermittent Incident.

Is the inspection result normal?

YES>>

Replace combination meter. Refer to Removal and Installation.

NO>>

Repair or replace.

Mass Air Flow Sensor Nissan Pathfinder 2026

Component Inspection (Mass Air Flow Sensor)

CHECK MASS AIR FLOW SENSOR-I

With CONSULT

  1. Turn ignition switch OFF.

  2. Reconnect all harness connectors disconnected.

  3. Start engine and warm it up to normal operating temperature.

  4. On CONSULT screen, select “ENGINE”>>“Data Monitor”.

  5. Check “MASS AIR FLOW SENSOR (Hz)” indication as following.

    Monitor itemConditionIndication
    MASS AIR FLOW SENSOR (Hz) Ignition switch ON (Engine stopped.) Approx. 3,700 Hz
    Idle (Engine is warmed-up to normal operating temperature.) 4,800 – 5,300 Hz
    2,500 rpm (Engine is warmed-up to normal operating temperature.) 5,900 – 6,500 Hz
    Idle to about 4,000 rpm 4,800 – 5,300 Hz → 6,400 – 7,200 Hz

Without CONSULT

  1. Turn ignition switch OFF.

  2. Reconnect all harness connectors disconnected.

  3. Start engine and warm it up to normal operating temperature.

  4. Check the frequency between ECM harness connector terminals under the following conditions.

    ECMConditionFrequency
    Connector+–
    TerminalTerminal
    F78

    33

    [MAF sensor signal]
    30 Ignition switch ON (Engine stopped.) Approx. 3,700 Hz
    Idle (Engine is warmed-up to normal operating temperature.) 4,800 – 5,300 Hz
    2,500 rpm (Engine is warmed-up to normal operating temperature.) 5,900 – 6,500 Hz
    Idle to about 4,000 rpm 4,800 – 5,300 Hz → 6,400 – 7,200 Hz

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

GO TO 2.

CHECK FOR THE CAUSE OF UNEVEN AIR FLOW THROUGH MASS AIR FLOW SENSOR

  1. Turn ignition switch OFF.

  2. Check for the cause of uneven air flow through mass air flow sensor. Refer to the following.

    • Crushed air ducts

    • Malfunctioning seal of air cleaner element

    • Uneven dirt of air cleaner element

    • Intake valve deposits

    • Improper specification of intake air system parts

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 3.

CHECK MASS AIR FLOW SENSOR-II

With CONSULT

  1. Repair or replace malfunctioning part.

  2. Start engine and warm it up to normal operating temperature.

  3. On CONSULT screen, select “ENGINE”>>“Data Monitor”.

  4. Check “MASS AIR FLOW SENSOR (Hz)” indication as following.

    Monitor itemConditionIndication
    MASS AIR FLOW SENSOR (Hz) Ignition switch ON (Engine stopped.) Approx. 3,700 Hz
    Idle (Engine is warmed-up to normal operating temperature.) 4,800 – 5,300 Hz
    2,500 rpm (Engine is warmed-up to normal operating temperature.) 5,900 – 6,500 Hz
    Idle to about 4,000 rpm 4,800 – 5,300 Hz → 6,400 – 7,200 Hz

Without CONSULT

  1. Repair or replace malfunctioning part.

  2. Start engine and warm it up to normal operating temperature.

  3. Check the frequency between ECM harness connector terminals under the following conditions.

    ECMConditionFrequency
    Connector+–
    TerminalTerminal
    F78

    33

    [MAF sensor signal]
    30 Ignition switch ON (Engine stopped.) Approx. 3,700 Hz
    Idle (Engine is warmed-up to normal operating temperature.) 4,800 – 5,300 Hz
    2,500 rpm (Engine is warmed-up to normal operating temperature.) 5,900 – 6,500 Hz
    Idle to about 4,000 rpm 4,800 – 5,300 Hz → 6,400 – 7,200 Hz

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

GO TO 4.

CHECK MASS AIR FLOW SENSOR-III

With CONSULT

  1. Turn ignition switch OFF.

  2. Disconnect mass air flow sensor harness connector and reconnect it again.

  3. Start engine and warm it up to normal operating temperature.

  4. On CONSULT screen, select “ENGINE”>>“Data Monitor”.

  5. Check “MASS AIR FLOW SENSOR (Hz)” indication as following.

    Monitor itemConditionIndication
    MASS AIR FLOW SENSOR (Hz) Ignition switch ON (Engine stopped.) Approx. 3,700 Hz
    Idle (Engine is warmed-up to normal operating temperature.) 4,800 – 5,300 Hz
    2,500 rpm (Engine is warmed-up to normal operating temperature.) 5,900 – 6,500 Hz
    Idle to about 4,000 rpm 4,800 – 5,300 Hz → 6,400 – 7,200 Hz

Without CONSULT

  1. Turn ignition switch OFF.

  2. Disconnect mass air flow sensor harness connector and reconnect it again.

  3. Start engine and warm it up to normal operating temperature.

  4. Check the frequency between ECM harness connector terminals under the following conditions.

    ECMConditionFrequency
    Connector+–
    TerminalTerminal
    F78

    33

    [MAF sensor signal]
    30 Ignition switch ON (Engine stopped.) Approx. 3,700 Hz
    Idle (Engine is warmed-up to normal operating temperature.) 4,800 – 5,300 Hz
    2,500 rpm (Engine is warmed-up to normal operating temperature.) 5,900 – 6,500 Hz
    Idle to about 4,000 rpm 4,800 – 5,300 Hz → 6,400 – 7,200 Hz

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Clean or replace malfunctioning mass air flow sensor.

On Board Refueling Vapor Recovery (orvr) Nissan Pathfinder 5th Gen

Component Function Check

CHECK ORVR FUNCTION

Check whether the following symptoms are present.

  • Fuel odor from EVAP canister is strong.

  • Cannot refuel/Fuel odor from the fuel filler opening is strong while refueling.

Are any symptoms present?

YES>>

Proceed to Diagnosis Procedure.

NO>>

INSPECTION END

Diagnosis Procedure

INSPECTION START

Check whether the following symptoms are present.

A: Fuel odor from EVAP canister is strong.

B: Cannot refuel/Fuel odor from the fuel filler opening is strong while refueling.

Which symptom is present?

A>>

GO TO 2.

B>>

GO TO 7.

CHECK EVAP CANISTER

  1. Remove EVAP canister with EVAP canister vent control valve and EVAP control system pressure sensor attached.

  2. Weigh the EVAP canister with EVAP canister vent control valve and EVAP control system pressure sensor attached.

    The weight should be less than 2.1 kg (4.6 lb).

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 4.

CHECK IF EVAP CANISTER IS SATURATED WITH WATER

Check if water will drain from EVAP canister.

Does water drain from the EVAP canister?

YES>>

GO TO 4.

NO>>

GO TO 6.

REPLACE EVAP CANISTER

Replace EVAP canister with a new one.

>>

GO TO 5.

DETECT MALFUNCTIONING PART

Check the EVAP hose between EVAP canister and Nissan Pathfinder vehicle frame for clogging or poor connection.

>>

Repair or replace EVAP hose.

CHECK REFUELING EVAP VAPOR CUT VALVE

Refer to Component Inspection.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace refueling EVAP vapor cut valve with fuel tank. Refer to Removal and Installation.

CHECK EVAP CANISTER

  1. Remove EVAP canister with EVAP canister vent control valve and EVAP control system pressure sensor attached.

  2. Weigh the EVAP canister with EVAP canister vent control valve and EVAP control system pressure sensor attached.

    The weight should be less than 2.1 kg (4.6 lb).

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

GO TO 9.

CHECK IF EVAP CANISTER IS SATURATED WITH WATER

Check if water will drain from EVAP canister.

Does water drain from the EVAP canister?

YES>>

GO TO 9.

NO>>

GO TO 11.

REPLACE EVAP CANISTER

Replace EVAP canister with a new one.

>>

GO TO 10.

DETECT MALFUNCTIONING PART

Check the EVAP hose between EVAP canister and Nissan Pathfinder vehicle frame for clogging or poor connection.

>>

Repair or replace EVAP hose.

CHECK VENT HOSES AND VENT TUBES

Check hoses and tubes between EVAP canister and refueling control valve for clogging, kinks, looseness and improper connection.

Is the inspection result normal?

YES>>

GO TO 12.

NO>>

Repair or replace hoses and tubes.

CHECK FILLER NECK TUBE

Check recirculation line for clogging, dents and cracks.

Is the inspection result normal?

YES>>

GO TO 13.

NO>>

Replace filler neck tube.

CHECK REFUELING EVAP VAPOR CUT VALVE

Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 14.

NO>>

Replace refueling EVAP vapor cut valve with fuel tank. Refer to Removal and Installation.

CHECK FUEL FILLER TUBE

Check filler neck tube and hose connected to the fuel tank for clogging, dents and cracks.

Is the inspection result normal?

YES>>

GO TO 15.

NO>>

Replace fuel filler tube. Refer to Exploded View.

CHECK ONE-WAY FUEL VALVE-I

Check one-way valve for clogging.

Is the inspection result normal?

YES>>

GO TO 16.

NO>>

Repair or replace one-way fuel valve with fuel tank. Refer to Removal and Installation.

CHECK ONE-WAY FUEL VALVE-II

  1. Make sure that fuel is drained from the tank.

  2. Remove fuel filler tube and hose.

  3. Check one-way fuel valve for operation as follows.

    When a stick is inserted, the valve should open, when removing stick it should close.

    Do not drop any material into the tank.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace fuel filler tube or replace one-way fuel valve with fuel tank. Refer to Removal and Installation.

Component Inspection

INSPECTION START

Do you have CONSULT?

Do you have CONSULT?

YES>>

GO TO 2.

NO>>

GO TO 3.

CHECK REFUELING EVAP VAPOR CUT VALVE

With CONSULT

  1. Turn ignition switch OFF.

  2. Remove fuel tank. Refer to Removal and Installation.

  3. Drain fuel from the tank as follows:

    1. Remove fuel feed hose located on the fuel gauge retainer.

    2. Connect a spare fuel hose, one side to fuel gauge retainer where the hose was removed and the other side to a fuel container.

    3. Drain fuel using “FPCM” in “Active test” mode of “ENGINE”.

  4. Check refueling EVAP vapor cut valve for being stuck to close as follows.

    Blow air into the refueling EVAP vapor cut valve (from the end of EVAP/ORVR line hose), and check that the air flows freely into the tank.

  5. Check refueling EVAP vapor cut valve for being stuck to open as follows.

    1. Connect vacuum pump to hose end.

    2. Remove fuel gauge retainer with fuel gauge unit.

      Always replace O-ring with new one.

    3. Turn fuel tank upside down.

    4. Apply vacuum pressure to hose end [−13.3 kPa (−0.136 kg/cm3, −1.93 psi)] with fuel gauge retainer remaining open and check that the pressure is applicable.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace refueling EVAP vapor cut valve with fuel tank.

CHECK REFUELING EVAP VAPOR CUT VALVE

Without CONSULT

  1. Turn ignition switch OFF.

  2. Remove fuel tank. Refer to Removal and Installation.

  3. Drain fuel from the tank as follows:

    1. Remove fuel gauge retainer.

    2. Drain fuel from the tank using a handy pump into a fuel container.

  4. Check refueling EVAP vapor cut valve for being stuck to close as follows.

    Blow air into the refueling EVAP vapor cut valve (from the end of EVAP/ORVR line hose), and check that the air flows freely into the tank.

  5. Check refueling EVAP vapor cut valve for being stuck to open as follows.

    1. Connect vacuum pump to hose end.

    2. Remove fuel gauge retainer with fuel gauge unit.

      Always replace O-ring with new one.

    3. Turn fuel tank upside down.

    4. Apply vacuum pressure to hose end [−13.3 kPa (−0.136 kg/cm3, −1.93 psi)] with fuel gauge retainer remaining open and check that the pressure is applicable.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace refueling EVAP vapor cut valve with fuel tank. Refer to Removal and Installation.

Refrigerant Pressure Sensor Nissan Pathfinder R53

Component Function Check

CHECK REFRIGERANT PRESSURE SENSOR FUNCTION

  1. Start engine and warm it up to normal operating temperature.

  2. Turn A/C switch and blower fan switch ON.

  3. Check the voltage between ECM harness connector terminals as per the following.

    ECMConditionVoltage
    +–
    ConnectorTerminalConnectorTerminal
    F79

    108

    (Refrigerant pressure sensor signal)
    F79 125

    [Engine is running]

    • Warm-up condition

    • Idle speed

    • Both A/C switch and blower fan motor switch: ON (Compressor operates)

    1.0 – 4.0 V

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Proceed to Diagnosis Procedure.

Diagnosis Procedure

CHECK GROUND CONNECTION

  1. Turn A/C switch and blower fan switch OFF.

  2. Turn ignition switch OFF.

  3. Check ground connection E9. Refer to Ground Inspection in Circuit Inspection.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace ground connection.

CHECK REFRIGERANT PRESSURE SENSOR POWER SUPPLY

  1. Disconnect refrigerant pressure sensor harness connector.

  2. Turn ignition switch ON.

  3. Check the voltage between refrigerant pressure sensor harness connector and ground.

    +−

    Voltage

    (Approx.)
    Refrigerant pressure sensor
    ConnectorTerminal
    E244 1 Ground 5 V

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

GO TO 3.

CHECK REFRIGERANT PRESSURE SENSOR POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between refrigerant pressure sensor harness connector and ECM harness connector.

    Refrigerant pressure sensorECMContinuity
    ConnectorTerminalConnectorTerminal
    E244 1 F79 136 Existed
  4. Also check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts.

CHECK SENSOR POWER SUPPLY 2 CIRCUIT

Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

Perform the trouble diagnosis for ECM power supply circuit. Refer to Diagnosis Procedure.

NO>>

Repair or replace error-detected parts.

CHECK REFRIGERANT PRESSURE SENSOR GROUND CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between refrigerant pressure sensor harness connector and ECM harness connector.

    Refrigerant pressure sensorECMContinuity
    ConnectorTerminalConnectorTerminal
    E244 3 F79 125 Existed
  4. Also check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace error-detected parts.

CHECK REFRIGERANT PRESSURE SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

  1. Check the continuity between refrigerant pressure sensor harness connector and ECM harness connector.

    Refrigerant pressure sensorECMContinuity
    ConnectorTerminalConnectorTerminal
    E244 2 F79 108 Existed
  2. Also check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair or replace error-detected parts.

CHECK INTERMITTENT INCIDENT

Refer to Intermittent Incident.

Is the inspection result normal?

YES>>

Replace refrigerant pressure sensor. Refer to Exploded View.

NO>>

Repair or replace error-detected parts.

Sensor Power Supply 2 Circuit Nissan Pathfinder SUV

Diagnosis Procedure

ECM supplies a voltage of 5 V to some of the sensors systematically divided into 3 groups, respectively. Accordingly, when a short circuit develops in a sensor power source, a malfunction may occur simultaneously in the sensors belonging to the same group as the short-circuited sensor.

Sensor power supply 1

  • APP sensor 1

  • Crankshaft position sensor 1

  • Exhaust camshaft position sensor (bank 1)

  • Throttle position sensor

  • Mass air flow sensor

  • Intake camshaft position sensor (bank 1)

  • Engine oil pressure sensor

Sensor power supply 2

  • APP sensor 2

  • Intake camshaft position sensor (bank2)

  • Refrigerant pressure sensor

  • Crankshaft position sensor 2

  • Exhaust camshaft position sensor (bank 2)

  • Fuel rail pressure sensor

Sensor power supply 3

  • EVAP control system pressure sensor

CHECK ECM POWER SUPPLY AND GROUND CIRCUIT

Perform trouble diagnosis for ECM power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts.

CHECK APP SENSOR 2 POWER SUPPLY CIRCUIT-1

  1. Turn ignition switch OFF.

  2. Disconnect accelerator pedal position (APP) sensor harness connector.

  3. Turn ignition switch ON.

  4. Check the voltage between APP sensor harness connector and ground.

    +-

    Voltage

    (Approx.)
    APP sensor
    ConnectorTerminal
    E31 5 Ground 5V

Is the inspection result normal?

YES>>

Refer to Intermittent Incident.

NO>>

GO TO 3.

CHECK APP SENSOR 2 POWER SUPPLY CIRCUIT-2

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between APP sensor harness connector and ECM harness connector.

    ++Continuity
    APP sensorECM
    ConnectorTerminalConnectorTerminal
    E25 2 E21 150 Existed

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair open circuit.

CHECK SENSOR POWER SUPPLY 2 CIRCUIT

  1. Disconnect following sensors harness connector.

  2. Check harness for short to power and short to ground, between the following terminals.

ECMSensor
ConnectorTerminalNameConnectorTerminal
F78 60 Intake camshaft position sensor (bank 2) F37 1
63 Crankshaft position sensor 2 F91 1
65 Exhaust camshaft position sensor (bank 2) F40 1
66 Fuel rail pressure sensor F97 3
F79 136 Refrigerant pressure sensor E244 1
E32 194 APP sensor 2 E31 5

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair short to ground or short to power in harness or connectors.

CHECK COMPONENTS

Check the following.

  • APP sensor 2 (Refer to Component Inspection (Accelerator Pedal Position Sensor).)

  • Intake camshaft position sensor (Refer to Component Inspection.)

  • Refrigerant pressure sensor (Refer to Component Function Check.)

  • Crankshaft position sensor 2 (Refer to Component Inspection (Crankshaft Position Sensor 2).)

  • Exhaust camshaft position sensor (bank 2) (Refer to Component Inspection.)

  • Fuel rail pressure sensor (Refer to Component Inspection (Fuel Rail Pressure Sensor).)

Is the inspection result normal?

YES>>

Refer to Intermittent Incident.

NO>>

Replace malfunctioning component.

Variable Induction Air System Nissan Pathfinder 2022

Component Function Check

CHECK OVERALL FUNCTION-I

With CONSULT

  1. Start engine and warm it up to the normal operating temperature.

  2. Perform “VIAS S/V-1” in “Active Test” mode of “ENGINE” with CONSULT.

  3. Turn VIAS control solenoid valve 1 “ON” and “OFF”, and check that power valve actuator 1 rod moves.

    Power valve actuator 1 Power valve actuator 1 rod Power valve actuator 2
    Power valve actuator 2 rod
    : Nissan Pathfinder Vehicle front

Without CONSULT

  1. Start engine and warm it up to the normal operating temperature.

  2. Rev engine quickly up to approximately 5,000 rpm.

  3. Check that power valve actuator 1 rod moves.

    Power valve actuator 1 Power valve actuator 1 rod Power valve actuator 2
    Power valve actuator 2 rod
    : Nissan Pathfinder Vehicle front

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Diagnosis Procedure.

CHECK OVERALL FUNCTION-II

With CONSULT

  1. Perform “VIAS S/V-2” in “Active Test” mode of “ENGINE” with CONSULT.

  2. Turn VIAS control solenoid valve 2 “ON” and “OFF”, and check that power valve actuator 2 rod moves.

    Power valve actuator 1 Power valve actuator 1 rod Power valve actuator 2
    Power valve actuator 2 rod
    : Nissan Pathfinder Vehicle front

Without CONSULT

  1. When revving engine up to 5,000 rpm quickly.

  2. Rev engine quickly up to approximately 5,000 rpm.

  3. Check that power valve actuator 2 rod moves.

    Power valve actuator 1 Power valve actuator 1 rod Power valve actuator 2
    Power valve actuator 2 rod
    : Nissan Pathfinder Vehicle front

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Diagnosis Procedure.

Diagnosis Procedure

INSPECTION START

Confirm the malfunctioning system (power valve 1 or power valve 2). Refer to Component Function Check.

Which system is related to the incident?

Power valve 1>>

GO TO 2.

Power valve 2>>

GO TO 6.

CHECK VACUUM EXISTENCE-I

With CONSULT

  1. Stop engine and disconnect vacuum hose connected to power valve actuator 1.

  2. Start engine and let it idle.

  3. Perform “VIAS S/V-1” in “Active Test” mode of “ENGINE” with CONSULT.

  4. Turn VIAS control solenoid valve 1 ON and OFF, and check vacuum existence under the following conditions.

    VIAS S/V-1Vacuum
    ON Existed
    OFF Not existed

Without CONSULT

  1. Stop engine and disconnect vacuum hose connected to power valve actuator 1.

  2. Disconnect VIAS control solenoid valve 1 harness connector.

  3. Start engine.

  4. Rev engine quickly up to approximately 5,000 rpm.

  5. Check vacuum existence under the following conditions.

    ConditionVacuum
    Idle Existed
    Rev engine quickly up to approximately 5,000 rpm Not existed

Is the inspection result normal?

YES>>

Repair or replace power valve actuator 1. Refer to Component Parts Location.

NO>>

GO TO 3.

CHECK VACUUM TANK

  1. Stop engine and disconnect vacuum hose connected to intake manifold collector.

  2. Start engine and let it idle.

  3. Check vacuum existence from intake manifold collector.

Does vacuum existence from the intake manifold collector?

YES>>

GO TO 4.

NO>>

Replace intake manifold collector. Refer to Removal and Installation.

CHECK VACUUM HOSE

  1. Stop engine.

  2. Check vacuum hose for crack, clogging, improper connection or disconnection. Refer to System Description.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair hoses or tubes.

CHECK VIAS CONTROL SOLENOID VALVE 1

Check VIAS control solenoid valve 1. Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Replace VIAS control solenoid valve 1. Refer to Component Parts Location.

CHECK VACUUM EXISTENCE-II

With CONSULT

  1. Stop engine and disconnect vacuum hose connected to power valve actuator 2.

  2. Start engine and let it idle.

  3. Perform “VIAS S/V-2” in “Active Test” mode of “ENGINE” with CONSULT.

  4. Turn VIAS control solenoid valve 2 ON and OFF, and check vacuum existence under the following conditions.

    VIAS S/V 2Vacuum
    ON Existed
    OFF Not existed

Without CONSULT

  1. Stop engine and disconnect vacuum hose connected to power valve actuator 2.

  2. Disconnect VIAS control solenoid valve 1 harness connector.

  3. Start engine.

  4. Rev engine quickly up to approximately 5,000 rpm.

  5. Check vacuum existence under the following conditions.

    ConditionOperation
    Idle Existed
    Rev engine quickly up to approximately 5,000 rpm Not existed

Is the inspection result normal?

YES>>

Repair or replace power valve actuator 2. Refer to Component Parts Location.

NO>>

GO TO 7.

CHECK VACUUM HOSE

  1. Stop engine.

  2. Check vacuum hose for crack, clogging, improper connection or disconnection. Refer to System Description.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair hoses or tubes.

CHECK VIAS CONTROL SOLENOID VALVE 2

Check VIAS control solenoid valve 2. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace VIAS control solenoid valve 2. Refer to Component Parts Location.