Power Window Control System - Dtc/circuit Diagnosis
- B2c40-04 Power Window Main Switch
- B2c41-04 Power Window Motor Fl
- Main Power Window and Door Mirror Switch Circuit
- Rear Power Window Switch Lh Circuit
- Lin Communication Circuit
B2c40-04 Power Window Main Switch Nissan Pathfinder SUV
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms (Trouble diagnosis content) | DTC detection condition | |
|---|---|---|---|
| B2C40-04 | Power window main switch (Main power window and door mirror switch) |
Diagnosis condition | Ignition switch OFF (auto ACC status) or ON. |
| Signal (terminal) | — | ||
| Threshold | CPU in power window main switch detects internal malfunction. | ||
| Diagnosis delay time | 1 seconds or less | ||
POSSIBLE CAUSE
Main power window and door mirror switch
FAIL SAFE
—
DTC CONFIRMATION PROCEDURE
PERFORM DTC CONFIRMATION PROCEDURE
CONSULT
Ignition switch ON.
Select “Self Diagnostic Result” mode of “BCM”.
Check DTC.
Is DTC detected?
YES>>Refer to DTC Diagnosis Procedure.
NO>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO>>Confirmation after repair: Inspection End.
DTC Diagnosis Procedure
REPLACE MAIN POWER WINDOW AND DOOR MIRROR SWITCH
Replace main power window and door mirror switch. Refer to Removal and Installation.
>>Inspection End.
B2c41-04 Power Window Motor Fl Nissan Pathfinder 5th Gen
DTC Description
DTC DETECTION LOGIC
| DTC No. | CONSULT screen terms (Trouble diagnosis content) | DTC detection condition | |
|---|---|---|---|
| B2C41-04 | Power window motor FL (Front power window motor LH) |
Diagnosis condition | When ignition switch ON or power window timer operates. |
| Signal (terminal) | — | ||
| Threshold | CPU in front power window motor LH detect internal malfunction. | ||
| Diagnosis delay time | 10 seconds | ||
POSSIBLE CAUSE
Front power window motor LH
FAIL SAFE
Front power window motor LH operation is stop or inching.
DTC CONFIRMATION PROCEDURE
PERFORM DTC CONFIRMATION PROCEDURE
CONSULT
Ignition switch ON.
Keep pulling the power window switch AUTO-UP for 5 seconds or more.
Keep pressing the power window switch AUTO-DOWN for 5 seconds or more.
Select “Self Diagnostic Result” mode of “BCM”.
Check DTC.
Is DTC detected?
YES>>Refer to DTC Diagnosis Procedure.
NO>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO>>Confirmation after repair: Inspection End.
DTC Diagnosis Procedure
REPLACE FRONT POWER WINDOW MOTOR LH
Replace front power window motor LH. Refer to Removal and Installation.
>>Inspection End.
Main Power Window and Door Mirror Switch Circuit Nissan Pathfinder 2026
Component Function Check
CHECK MAIN POWER WINDOW AND DOOR MIRROR SWITCH FUNCTION
Check front power window motor LH operation using main power window and door mirror switch.
Is the inspection result normal?
YES>>Inspection End.
NO>>Refer to Diagnosis Procedure.
Diagnosis Procedure
CHECK MAIN POWER WINDOW AND DOOR MIRROR SWITCH CIRCUIT
Ignition switch OFF, and then wait for 3 minutes with driver door open.
Disconnect front power window motor LH connector and main power window and door mirror switch connector.
Check continuity between front power window motor LH harness connector and main power window and door mirror switch harness connector.
Main power window and door mirror switch Front power window motor LH Continuity Connector Terminal Connector Terminal D24 1 D9 2 Yes 13 1 Check continuity between main power window and door mirror switch harness connector and ground.
Main power window and door mirror switch — Continuity Connector Terminal D24 1 Ground No 13
Is the inspection result normal?
YES>>Inspection End.
NO>>Repair or replace harness.
Rear Power Window Switch Lh Circuit Nissan Pathfinder 2022
Component Function Check
CHECK FUNCTION
Check rear power window motor LH operation.
Is the inspection result normal?
YES>>Inspection End.
NO>>Refer to Diagnosis Procedure.
Diagnosis Procedure
CHECK REAR POWER WINDOW SWITCH LH CIRCUIT
Ignition switch OFF.
Disconnect rear power window motor LH connector and rear power window switch LH connector.
Check continuity between rear power window motor LH harness connector and rear power window switch LH harness connector.
Rear power window motor LH Rear power window switch LH Continuity Connector Terminal Connector Terminal D204 1 D208 2 Yes 2 3 Check continuity between rear power window switch LH harness connector and ground.
Rear power window switch LH — Continuity Connector Terminal D208 2 Ground No 3
Is the inspection result normal?
YES>>GO TO 2.
NO>>Repair or replace harness.
CHECK REAR POWER WINDOW SWITCH LH
Check rear power window switch LH.
Refer to Component Inspection.
Is the inspection result normal?
YES>>Inspection End.
NO>>Replace rear power window switch LH. Refer to Removal and Installation.
Component Inspection
CHECK REAR POWER WINDOW SWITCH LH
Disconnect rear power window switch LH connector.
Check continuity between rear power window switch LH terminals under the following conditions:
Rear power window switch LH Condition Continuity Terminals (+) (-) 3 5 NEUTRAL No UP Yes 2 NEUTRAL No DOWN Yes
Is the inspection result normal?
YES>>Inspection End.
NO>>Replace rear power window switch LH. Refer to Removal and Installation.
Lin Communication Circuit Nissan Pathfinder
Diagnosis Procedure
CHECK BCM OUTPUT SIGNAL
Ignition switch ON.
Check signal between BCM harness connector and ground using an oscilloscope.
(+) (−) Signal
(Reference value)BCM Connector Terminal M18 24 Ground 
Is the inspection result normal?
YES>>GO TO 3.
NO>>GO TO 2.
CHECK LIN COMMUNICATION CIRCUIT
Ignition switch OFF, and then wait for 3 minutes with driver door open.
Disconnect following connectors:
BCM
Main power window and door mirror switch
Front power window motor LH
Front power window motor RH
Rear power window motors
Passenger door mirror control module (if equipped)
Moonroof motor assembly (if equipped)
Sunshade motor assembly (if equipped)
Connecting parts other than power window, refer to Wiring Diagram.
Check continuity between BCM harness connector and ground.
BCM — Continuity Connector Terminal M18 24 Ground No
Is the inspection result normal?
YES>>Replace BCM. Refer to Removal and Installation.
NO>>Repair or replace harness.
CHECK LIN COMMUNICATION SIGNAL
Ignition switch OFF, and then wait for 3 minutes with driver door open.
Disconnect following connectors:
Main power window and door mirror switch
Front power window motor LH
Front power window motor RH
Rear power window motors
Ignition switch ON.
Check signal between main power window and door mirror switch harness connector, front power window motor LH harness connector, front power window motor RH harness connector, and rear power window motors harness connectors and ground using an oscilloscope.
(+) (−) Signal
(Reference value)Connector Terminal Main power window and door mirror switch D24 4 Ground 
Front power window motor LH D9 6 Front power window motor RH D105 6 Rear power window motor LH D204 6 Rear power window motor RH D304 6
Is the inspection result normal?
YES>>Inspection End.
NO>>Main power window and door mirror switch: GO TO 4.
NO>>Front power window motor LH: GO TO 5.
NO>>Front power window motor RH: GO TO 6.
NO>>Rear power window motors: GO TO 7.
CHECK LIN COMMUNICATION CIRCUIT (MAIN POWER WINDOW AND DOOR MIRROR SWITCH)
Ignition switch OFF.
Disconnect BCM connector.
Check continuity between BCM harness connector and main power window and door mirror switch harness connector.
BCM Main power window and door mirror switch Continuity Connector Terminal Connector Terminal M18 24 D24 4 Yes
Is the inspection result normal?
YES>>Inspection End.
NO>>Repair or replace harness.
CHECK LIN COMMUNICATION CIRCUIT (FRONT POWER WINDOW MOTOR LH)
Ignition switch OFF.
Disconnect BCM connector.
Check continuity between BCM harness connector and front power window motor LH harness connector.
BCM Front power window motor LH Continuity Connector Terminal Connector Terminal M18 24 D9 6 Yes
Is the inspection result normal?
YES>>Inspection End.
NO>>Repair or replace harness.
CHECK LIN COMMUNICATION CIRCUIT (FRONT POWER WINDOW MOTOR RH)
Ignition switch OFF.
Disconnect BCM connector.
Check continuity between BCM harness connector and front power window motor RH harness connector.
BCM Front power window motor RH Continuity Connector Terminal Connector Terminal M18 24 D105 6 Yes
Is the inspection result normal?
YES>>Inspection End.
NO>>Repair or replace harness.
CHECK LIN COMMUNICATION CIRCUIT (REAR POWER WINDOW MOTORS)
Ignition switch OFF.
Disconnect BCM connector.
Check continuity between BCM harness connector and rear power window motors harness connector.
BCM Rear power window motors Continuity Connector Terminal Connector Terminal M18 24 LH D204 6 Yes RH D304
Is the inspection result normal?
YES>>Inspection End.
NO>>Repair or replace harness.