Engine Control System - Dtc/circuit Diagnosis

In this manual: Engine Control System - Dtc/circuit Diagnosis
General Information — 8Engine :: Engine Mechanical — 19Engine Lubrication System - Precautions. Preparation — 1Engine Lubrication System - Lubrication System (System Description). Engine Oil Pressure (Basic Inspection). Service Data and Specifications (SDS) — 1Engine Cooling System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Engine Cooling System - Engine Coolant — 1Engine Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Engine Control System - Ecu Diagnosis Information — 1Ecu Diagnosis Information - Ecm ++ — 1Engine Control System - Basic Inspection — 1Basic Inspection - Diagnosis and Repair Workflow ++ — 1Basic Inspection - Basic Inspection ++ — 1Basic Inspection - Additional Service When Replacing Ecm ++ — 1Basic Inspection - Fuel Pressure Check ++ — 1Basic Inspection - How to Set Srt Code ++ — 1Basic Inspection - How to Erase Permanent Dtc ++ — 1Engine Control System - Dtc/circuit Diagnosis — 1Engine Control System - Symptom Diagnosis — 1Engine Control System - Periodic Maintenance — 1Engine Control System - Removal and Installation — 1Fuel System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Fuel System - Fuel System (Periodic Maintenance). Fuel Level Sensor Unit (Disassembly and Assembly) — 1Exhaust System - Precautions. Preparation — 1Exhaust System - Exhaust System (Periodic Maintenance). Exhaust System (Removal and Installation) — 1Starting System - Precautions. Preparation. Starter Motor (Service Data and Specifications (sds)) — 1Starting System - Diagnosis and Repair Work Flow — 1Starting System - Starting System (Symptom Diagnosis). Starter Motor (Removal and Installation) — 1Accelerator Control System - Precautions. Service Data and Specifications (SDS) — 1Accelerator Control System - Accelerator Pedal Assembly — 1Transmission & Driveline :: Transaxle & Transmission — 21Driveline - System Description — 1Transfer: Ty92b - Ecu Diagnosis Information. Awd Control Unit ++ — 1Driveline - Basic Inspection — 1Driveline - Dtc/circuit Diagnosis — 1Driveline - Symptom Diagnosis — 1Driveline - Removal and Installation — 1Transfer: Ty92b - Unit Removal and Installation. Transfer Assembly ++ — 1Driveline - Unit Disassembly and Assembly — 1Driveline - Basic Inspection — 1Driveline - Removal and Installation — 1Driveline - Unit Disassembly and Assembly — 1Front Axle - Precautions. Preparation — 1Front Axle - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Front Axle - Front Drive Shaft Boot — 1Front Axle - Front Drive Shaft — 1Rear Axle - Precautions. Preparation. Service Data and Specifications (SDS) — 1Rear Axle - Noise, Vibration and Harshness (nvh) Troubleshooting — 1Rear Axle - Rear Drive Shaft — 1Suspension :: Front Suspension — 7Rear Suspension - Precautions. Preparation — 1Rear Suspension - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Rear Suspension - Rear Suspension Assembly — 1Road Wheels & Tires - Precautions — 1Road Wheels & Tires - Preparation. Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Road Wheels & Tires - System — 1Brakes :: Brake System — 9Parking Brake System - Precautions. Preparation — 1Parking Brake System - System — 1Vdc/tcs/abs - Precautions ++ — 1Brake Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Dtc/circuit Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Steering :: Steering System — 9Steering Control System - Precautions — 1Steering Control System - System — 1Steering Control System - Eps Control Unit (Ecu Diagnosis Information. Removal and Installation) — 1Restraints :: Seat Belt — 7Srs Air Bag - Precautions. Preparation — 1Srs Air Bag - Collision Diagnosis — 1Srs Air Bag - Occupant Classification System — 1Srs Air Bag Control System - Precautions — 1Srs Air Bag Control System - System — 1Srs Air Bag Control System - Diagnosis Sensor Unit — 1Srs Air Bag Control System - Inspection and Adjustment — 1Ventilation, Heater & Air Conditioner :: Ventilation System — 6Heater & Air Conditioning System - Precautions — 1Heater & Air Conditioning System - Preparation — 1Heater & Air Conditioning System - Component Parts — 1Heater & Air Conditioning System - Diagnosis and Repair Work Flow — 1Heater & Air Conditioning System - Compressor — 1Heater & Air Conditioning System - Cooler Pipe and Hose — 1Heater & Air Conditioning System - Condenser. Condenser — 1Heater & Air Conditioning System - Heating and Cooling Unit Assembly — 1Heater & Air Conditioning System - Service Data and Specifications (SDS) — 1Heater & Air Conditioning Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1Heater & Air Conditioning Control System - Ecu Diagnosis Information — 1Heater & Air Conditioning Control System - Basic Inspection — 1Heater & Air Conditioning Control System - Dtc/circuit Diagnosis — 1Heater & Air Conditioning Control System - Symptom Diagnosis — 1Heater & Air Conditioning Control System - Removal and Installation — 1Body Interior :: Interior — 8Instrument Panel - Precautions. Preparation. Clip List — 1Instrument Panel - Squeak and Rattle Trouble Diagnoses — 1Instrument Panel - Cluster Lid C — 1Seat - Precautions — 1Seat - Preparation. Clip List — 1Seat - Component Parts — 1Seat - System — 1Seat - Diagnosis and Repair Work Flow — 1Seat - Front Seat — 1Seat - Second Row Seats — 1Seat - Third Row Seats — 1Seat - Front Seat — 1Seat - Second Row Seat — 1Seat - Third Row Seat — 1Automatic Drive Positioner - Precautions. Preparation — 1Automatic Drive Positioner - System — 1Automatic Drive Positioner - Diagnosis and Repair Work Flow — 1Automatic Drive Positioner - Inspection and Adjustment — 1Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock — 38Security Control System - Precautions — 1Security Control System - System — 1Security Control System - Ecm, Bcm, Intelligent Key Unit, Ipdm E/r — 1Security Control System - Vehicle Security System Cannot Be Set — 1Glass & Window System - Precautions. Preparation — 1Glass & Window System - Squeak and Rattle Trouble Diagnoses — 1Power Window Control System - Precautions. Preparation — 1Power Window Control System - Power Supply and Ground Circuit — 1Power Window Control System - Power Window Motor Circuit — 1Power Window Control System - Front Power Window Rh Alone Does Not Operate — 1Power Window Control System - Rear Lh Side Power Window Alone Does Not Operate — 1Power Window Control System - Rear Rh Side Power Window Alone Does Not Operate — 1Roof - Precautions. Preparation — 1Roof - Power Supply and Ground Circuit — 1Roof - Moonroof Switch Assembly — 1Roof - Lin Communication Circuit — 1Roof - Auto Operation Does Not Operate — 1Roof - Anti-Pinch Function Does Not Operate — 1Exterior - Precautions. Preparation. Clip List (Preparation) — 1Exterior - Squeak and Rattle Trouble Diagnoses — 1Exterior - Fender Protector — 1Exterior - Over Fender — 1Exterior - Under Cover — 1Exterior - Roof Side Rail — 1Body Repair - Service Information — 1Service Information - Sheet Metal Work ++ — 1Service Information - Body Welding and Precautions ++ — 1Service Information - Safety and Health ++ — 1Service Information - Repairing Procedures and Precautions ++ — 1Body Repair - Precaution — 1Body Repair - Preparation — 1Body Repair - Removal and Installation — 1Driver Controls :: Mirrors — 8Exterior Lighting System - System Description — 1System Description - Component Parts ++ — 1Exterior Lighting System - Basic Inspection — 1Exterior Lighting System - Dtc/circuit Diagnosis — 1Exterior Lighting System - Symptom Diagnosis — 1Exterior Lighting System - Periodic Maintenance — 1Exterior Lighting System - Removal and Installation — 1Interior Lighting System - Precautions. Preparation — 1Interior Lighting System - Component Parts. Interior Lighting System — 1Interior Lighting System - System — 1Interior Lighting System - Diagnosis and Repair Work Flow — 1Interior Lighting System - Interior Lighting System Symptoms (Symptom Diagnosis). Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Interior Lighting System - Foot Lamp — 1Wiper & Washer - Precautions — 1Wiper & Washer - Preparation. Bcm, Ipdm E/r (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Wiper & Washer - System — 1Wiper & Washer - Diagnosis and Repair Work Flow — 1Defogger - Precautions. Bcm, A/c Auto Amp. (Ecu Diagnosis Information) — 1Defogger - Diagnosis and Repair Work Flow — 1Horn - Precautions — 1Electrical & Power Control :: Power Outlet — 13Body Control System - Precautions. Preparation — 1Body Control System - Component Parts — 1Body Control System - System — 1Body Control System - Diagnosis System (bcm) — 1Body Control System - Bcm — 1Lan System - System Description — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - Removal and Installation — 1Charging System - Precautions. Preparation. Ecm, Ipdm E/r (Ecu Diagnosis Information) — 1Charging System - Diagnosis and Repair Work Flow — 1Charging System - Charging System (Symptom Diagnosis). Generator (Removal and Installation). Service Data and Specifications (SDS) — 1Power Supply, Ground & Circuit Elements - Precautions. Preparation. Service Data and Specifications (SDS) — 1Driver Information & Multimedia :: Meter, Warning Lamp & Indicator — 25Warning Chime System - Application Notice (How to Use This Manual). Precautions — 1Warning Chime System - System — 1Warning Chime System - Diagnosis System (combination Meter) — 1Warning Chime System - Bcm, Combination Meter (Ecu Diagnosis Information). Diagnosis and Repair Work Flow (Basic Inspection) — 1Sonar System - Precautions. Preparation — 1Sonar System - Sonar Control Unit — 1Dtc/circuit Diagnosis - B2720 Corner Sensor [rl] ++ — 1Audio, Visual & Navigation System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Multi Av (av Control Unit) ++ — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Symptom Diagnosis - Multi Av System ++ — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Cruise Control & Driver Assistance :: Cruise Control System — 17Driver Assistance System - System Description — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Driver Assistance System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1System Description - Handling Precaution ++ — 1Driver Assistance System - Ecu Diagnosis Information — 1Driver Assistance System - Basic Inspection — 1Basic Inspection - Distance Sensor Alignment ++ — 1Basic Inspection - Camera Aiming Adjustment ++ — 1Basic Inspection - Action Test ++ — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Laser/radar (distance Sensor) ++ — 1Dtc/circuit Diagnosis - Lane Camera (front Camera Unit) ++ — 1Driver Assistance System - Symptom Diagnosis — 1Driver Assistance System - Removal and Installation — 1Driver Assistance System - System Description — 1System Description - System ++ — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Drive Mode System - Precautions — 1Drive Mode System - Component Parts. Drive Mode System — 1Drive Mode System - System — 1Drive Mode System - Diagnosis and Repair Work Flow — 1Drive Mode System - Drive Mode Select Switch Circuit — 1Maintenance - Precautions. Preparation — 1Maintenance - General Maintenance — 1Maintenance - Periodic Maintenance — 1Maintenance - Recommended Fluids and Lubricants — 1Maintenance - Engine Maintenance — 1Maintenance - Chassis and Body Maintenance — 1Engine Lubrication System - Periodic Maintenance — 1Engine Lubrication System - Removal and Installation — 1Engine Cooling System - System Description — 1Engine Cooling System - Removal and Installation — 1Engine Control System - Vq35dd — 1Fuel System - Removal and Installation — 1Starting System - System Description — 1Starting System - Dtc/circuit Diagnosis — 1Driveline - Transfer: Ty92b — 1Driveline - Rear Propeller Shaft: 3fcj-Cvj — 1Driveline - Rear Final Drive: R145 — 1Front Axle - Periodic Maintenance — 1Front Axle - Removal and Installation — 1Rear Axle - Periodic Maintenance — 1Rear Axle - Removal and Installation — 1Rear Suspension - Removal and Installation — 1Road Wheels & Tires - System Description — 1Road Wheels & Tires - Basic Inspection — 1Road Wheels & Tires - Dtc/circuit Diagnosis — 1Road Wheels & Tires - Symptom Diagnosis — 1Road Wheels & Tires - Periodic Maintenance — 1Road Wheels & Tires - Removal and Installation — 1Parking Brake System - System Description — 1Parking Brake System - Basic Inspection — 1Parking Brake System - Dtc/circuit Diagnosis — 1Parking Brake System - Symptom Diagnosis — 1Parking Brake System - Removal and Installation — 1Brake Control System - Vdc/tcs/abs — 1Brake Control System - Automatic Brake Hold — 1Brake Control System - Automatic Emergency Braking — 1Brake Control System - Rear Automatic Braking — 1Steering Control System - System Description — 1Steering Control System - Basic Inspection — 1Steering Control System - Dtc/circuit Diagnosis — 1Steering Control System - Symptom Diagnosis — 1Srs Air Bag - Removal and Installation — 1Srs Air Bag Control System - System Description — 1Srs Air Bag Control System - Basic Inspection — 1Srs Air Bag Control System - Symptom Diagnosis — 1Heater & Air Conditioning System - Symptom Diagnosis — 1Heater & Air Conditioning System - Periodic Maintenance — 1Heater & Air Conditioning Control System - Automatic Air Conditioning — 1Instrument Panel - Removal and Installation — 1Instrument Panel - Unit Disassembly and Assembly — 1Seat - Ecu Diagnosis Information — 1Seat - Dtc/circuit Diagnosis — 1Seat - Symptom Diagnosis — 1Automatic Drive Positioner - System Description — 1Automatic Drive Positioner - Ecu Diagnosis Information — 1Automatic Drive Positioner - Dtc/circuit Diagnosis — 1Automatic Drive Positioner - Symptom Diagnosis — 1Automatic Drive Positioner - Removal and Installation — 1Security Control System - System Description — 1Security Control System - Basic Inspection — 1Security Control System - Dtc/circuit Diagnosis — 1Security Control System - Symptom Diagnosis — 1Security Control System - Removal and Installation — 1Glass & Window System - Removal and Installation — 1Power Window Control System - System Description — 1Power Window Control System - Ecu Diagnosis Information — 1Power Window Control System - Basic Inspection — 1Power Window Control System - Dtc/circuit Diagnosis — 1Power Window Control System - Symptom Diagnosis — 1Power Window Control System - Removal and Installation — 1Roof - System Description — 1Roof - Ecu Diagnosis Information — 1Roof - Basic Inspection — 1Roof - Dtc/circuit Diagnosis — 1Roof - Symptom Diagnosis — 1Roof - Removal and Installation — 1Exterior - System Description — 1Exterior - Removal and Installation — 1Body Repair - Repair Information — 1Exterior Lighting System - Led Headlamp — 1Interior Lighting System - Dtc/circuit Diagnosis — 1Interior Lighting System - Removal and Installation — 1Wiper & Washer - System Description — 1Wiper & Washer - Dtc/circuit Diagnosis — 1Wiper & Washer - Symptom Diagnosis — 1Wiper & Washer - Removal and Installation — 1Defogger - System Description — 1Defogger - Dtc/circuit Diagnosis — 1Defogger - Symptom Diagnosis — 1Defogger - Removal and Installation — 1Horn - Removal and Installation — 1Body Control System - Basic Inspection — 1Body Control System - Dtc/circuit Diagnosis — 1Body Control System - Symptom Diagnosis — 1Body Control System - Removal and Installation — 1Lan System - Can Fundamental — 1Lan System - Can — 1Lan System - Can Gateway — 1Power Control System - Ipdm E/r — 1Power Control System - Power Distribution System — 1Charging System - System Description — 1Charging System - Dtc/circuit Diagnosis — 1Power Supply, Ground & Circuit Elements - System Description — 1Power Supply, Ground & Circuit Elements - Basic Inspection — 1Power Supply, Ground & Circuit Elements - Removal and Installation — 1Warning Chime System - System Description — 1Warning Chime System - Dtc/circuit Diagnosis — 1Warning Chime System - Symptom Diagnosis — 1Sonar System - System Description — 1Sonar System - Basic Inspection — 1Sonar System - Dtc/circuit Diagnosis — 1Sonar System - Symptom Diagnosis — 1Sonar System - Removal and Installation — 1Audio, Visual & Navigation System - Nissanconnect — 1Audio, Visual & Navigation System - Intelligent Around View Monitor System — 1Audio, Visual & Navigation System - Rear View Monitor System — 1Audio, Visual & Navigation System - Telematics System — 1Driver Assistance System - Adas Control Unit 2 — 1Driver Assistance System - Driver Assistance System — 1Driver Assistance System - Chassis Control — 1Drive Mode System - Removal and Installation — 1Dtc/circuit Diagnosis (C053c Wheel Speed Sensor ... U2141 Can Comm Circuit) — 1Dtc/circuit Diagnosis (P0011 Intake Valve Timing Control ... P0111 Iat Sensor) — 1Dtc/circuit Diagnosis (P0116 Engine Coolant Temperature Sensor ... P025b Fuel Pump Module a) — 1Dtc/circuit Diagnosis (P026b Injection Timing ... P0420 Three Way Catalyst Function) — 1Dtc/circuit Diagnosis (P0441 Evap Control System ... P0524 Engine Oil Pressure) — 1Dtc/circuit Diagnosis (P0532 A/c Refrigerant Pressure Sensor ... P064d Ecm) — 1Dtc/circuit Diagnosis (P06da Engine Oil Pressure Control Solenoid Valve ... P1217 Engine Over Temperature) — 1Dtc/circuit Diagnosis (P1220 Fuel Pump Control Module (fpcm) ... P1574 Ascd Vehicle Speed Sensor) — 1Dtc/circuit Diagnosis (P1575 Brake Switch ... P2101 Electric Throttle Control Function) — 1Dtc/circuit Diagnosis (P2118 Throttle Control Motor ... P34ac Electric Intake Valve Timing Control Actuator) — 1Dtc/circuit Diagnosis (Active Grille Shutter ... High Pressure Fuel Pump) — 1Dtc/circuit Diagnosis (Ignition Signal ... Variable Induction Air System) — 14012 C1040 Emergency Brake — 14013 C106a Wheel Sensor — 14014 C1078-55 Not Configuration — 14015 C10b4-98 Overheat — 14016 B1001 Lap Pre-Tensioner Lh — 14017 B0001 Driver Air Bag Module — 14018 B100e Knee Air Bag Module Rh — 14019 B142x Collision Detection — 1Dtc/circuit Diagnosis (B20c7-11 A/c Clutch ... B24a6-11 in-Vehicle Sensor) — 1Dtc/circuit Diagnosis (B24a6-15 in-Vehicle Sensor ... U2140-87 Can Comm Err (ecm)) — 1Dtc/circuit Diagnosis (C1f00-1c Control Unit ... C1f04-61 Brake Sw/stop Lamp Sw) — 1Dtc/circuit Diagnosis (C1f05-49 Front Camera Unit ... C1f70-87 Ethernet Circuit) — 1
97steps
~582min
4/5difficulty
Done 0 of 97

Trouble Diagnosis - Specification Value Nissan Pathfinder

Component Function Check

PRECONDITIONING

With CONSULT

Make sure that all of the following conditions are satisfied.

TESTING CONDITION

  • Nissan Pathfinder Vehicle driven distance: More than 5,000 km (3,107 miles)

  • Barometric pressure: 98.3 – 104.3 kPa (1.003 – 1.064 kg/cm2, 14.25 – 15.12 psi)

  • Atmospheric temperature: 20 – 30 °C

  • Engine coolant temperature: 75 – 95 °C

  • Transmission: Warmed-up

  • After the engine is warmed up to normal operating temperature, drive Nissan Pathfinder vehicle until “FULUD TEMP” in “Data Monitor” of “TRANSMISSION” indicates more than 60 °C.

  • Electrical load: Not applied

    • Rear window defogger switch, air conditioner switch, lighting switch are OFF. Steering wheel is straight ahead.

  • Engine speed: Idle

>>

GO TO 2.

CHECK REFERENCE OF DATA MONITOR MODE

With CONSULT

  1. Perform Work Procedure.

  2. On CONSULT screen, select “ENGINE”>>“Data Monitor”.

  3. Select “Reference” and change “DISPLAY TYPE” to “Line Graph”.

  4. Select “B/FUEL SCHDL”, “A/F ALPHA-B1”, “A/F ALPHA-B2”, and “MASS AIR FLOW SENSOR (Hz)”.

  5. Make sure that monitor items are within the Reference.

Is the measurement value within the Reference?

YES>>

INSPECTION END

NO>>

Proceed to Diagnosis Procedure.

Diagnosis Procedure

The specification Reference indicated at “Reference” of “Data Monitor” mode indicates the tolerance of the ECM input/output valve when the engine control system operates normally.

When the indicated value on “Data Monitor” mode is within the Reference, the engine control system is confirmed OK. When the indicated value on “Data Monitor” mode is not within the Reference, the engine control system may have one or more malfunctions.

The Reference is used to detect malfunctions that may affect the engine control system, but will not illuminate the MIL.

The Reference will be displayed for the following three items:

  • B/FUEL SCHDL (The fuel injection pulse width programmed into ECM prior to any learned on board correction)

  • A/F ALPHA-B1/B2 (The mean value of air-fuel ratio feedback correction factor per cycle)

  • MASS AIR FLOW SENSOR (Hz) (The frequency of the mass air flow sensor)

OVERALL SEQUENCE

DETAILED PROCEDURE

CHECK “A/F ALPHA-B1” AND “A/F ALPHA-B2”

With CONSULT

  1. Start engine.

  2. Confirm that the testing conditions are met. Refer to Component Function Check.

  3. On CONSULT screen, select “ENGINE”>>“Data Monitor”.

  4. Select “Reference” and change “DISPLAY TYPE” to “Line Graph”.

  5. Select “A/F ALPHA-B1” and “A/F ALPHA-B2”.

  6. Make sure that each indication is within the Reference.

Is the measurement value within the Reference?

YES>>

GO TO 17.

NO-1>>

Less than the Reference: GO TO 2.

NO-2>>

More than the Reference: GO TO 3.

CHECK “B/FUEL SCHDL”

With CONSULT

Select “B/FUEL SCHDL” at “Reference” of “Data Monitor” mode, and make sure that the indication is within the Reference.

Is the measurement value within the Reference?

YES>>

GO TO 4.

NO>>

More than the Reference: GO TO 19.

CHECK “B/FUEL SCHDL”

With CONSULT

Select “B/FUEL SCHDL” at “Reference” of “Data Monitor” mode, and make sure that the indication is within the Reference.

Is the measurement value within the Reference?

YES>>

GO TO 6.

NO-1>>

More than the Reference: GO TO 6.

NO-2>>

Less than the Reference: GO TO 25.

CHECK “A/F ALPHA-B1” AND “A/F ALPHA-B2”

With CONSULT

  1. Stop the engine.

  2. Disconnect PCV hose, and then plug it.

  3. Start engine.

  4. Select “A/F ALPHA-B1” and “A/F ALPHA-B2” at “Reference” of “Data Monitor” mode, and make sure that the indication is within the Reference.

Is the measurement value within the Reference?

YES>>

GO TO 5.

NO>>

GO TO 6.

CHANGE ENGINE OIL

  1. Stop the engine.

  2. Change engine oil. Refer to Inspection.

>>

INSPECTION END

CHECK FUEL PRESSURE

Check fuel pressure. (Refer to Work Procedure.)

Is the inspection result normal?

YES>>

GO TO 9.

NO-1>>

Fuel pressure is too high: Replace “fuel filter and fuel pump assembly” and then GO TO 8.

NO-2>>

Fuel pressure is too low: GO TO 7.

DETECT MALFUNCTIONING PART

Check fuel hoses and fuel tubes for clogging.

Is the inspection result normal?

YES>>

Replace “fuel filter and fuel pump assembly” and then GO TO 8.

NO>>

Repair or replace and then GO TO 8.

CHECK “A/F ALPHA-B1” AND “A/F ALPHA-B2”

With CONSULT

  1. Start engine.

  2. Select “A/F ALPHA-B1” and “A/F ALPHA-B2” at “Reference” of “Data Monitor” mode, and make sure that the indication is within the Reference.

Is the measurement value within the Reference?

YES>>

INSPECTION END

NO>>

GO TO 9.

PERFORM POWER BALANCE TEST

With CONSULT

  1. Perform “POWER BALANCE” in “Active Test” mode.

  2. Make sure that the each cylinder produces a momentary engine speed drop.

Is the inspection result normal?

YES>>

GO TO 12.

NO>>

GO TO 10.

DETECT MALFUNCTIONING PART

Check the following bellow.

  • Ignition coil and its circuit (Refer to Component Function Check.)

  • Fuel injector and its circuit (Refer to Component Function Check.)

  • Intake air leakage

  • Low compression pressure (Refer to On-Nissan Pathfinder Vehicle Service.)

Is the inspection result normal?

YES>>

Replace fuel injector and then GO TO 11.

NO>>

Repair or replace malfunctioning part and then GO TO 11.

CHECK “A/F ALPHA-B1” AND “A/F ALPHA-B2”

With CONSULT

  1. Start engine.

  2. Select “A/F ALPHA-B1” and “A/F ALPHA-B2” at “Reference” of “Data Monitor” mode, and make sure that the indication is within the Reference.

Is the measurement value within the Reference?

YES>>

INSPECTION END

NO>>

GO TO 12.

CHECK A/F SENSOR 1 FUNCTION

Perform all DTC CONFIRMATION PROCEDURE related with A/F sensor 1.

  • For DTC P0130, P0150, refer to DTC Description.

  • For DTC P0131, P0151, refer to DTC Description.

  • For DTC P0132, P0152, refer to DTC Description.

  • For DTC P014C, P014D, P014E, P014F, P015A, P015B, P015C, P015D, refer to DTC Description.

  • For DTC P2096, P2097, P2098, P2099, refer to DTC Description.

Are any DTCs detected?

YES>>

GO TO 13.

NO>>

GO TO 15.

CHECK A/F SENSOR 1 CIRCUIT

Perform Diagnosis Procedure according to corresponding DTC.

>>

GO TO 14.

CHECK “A/F ALPHA-B1” AND “A/F ALPHA-B2”

With CONSULT

  1. Start engine.

  2. Select “A/F ALPHA-B1” and “A/F ALPHA-B2” at “Reference” of “Data Monitor” mode, and make sure that the indication is within the Reference.

Is the measurement value within the Reference?

YES>>

INSPECTION END

NO>>

GO TO 15.

DISCONNECT AND RECONNECT ECM HARNESS CONNECTOR

  1. Stop the engine.

  2. Disconnect ECM harness connector. Check pin terminal and connector for damage, and then reconnect it.

>>

GO TO 16.

CHECK “A/F ALPHA-B1” AND “A/F ALPHA-B2”

With CONSULT

  1. Start engine.

  2. Select “A/F ALPHA-B1” and “A/F ALPHA-B2” at “Reference” of “Data Monitor” mode, and make sure that the indication is within the Reference.

Is the measurement value within the Reference?

YES>>

INSPECTION END

NO>>

Detect malfunctioning part according to Symptom Table.

CHECK “B/FUEL SCHDL”

With CONSULT

Select “B/FUEL SCHDL” at “Reference” of “Data Monitor” mode, and make sure that the indication is within the Reference.

Is the measurement value within the Reference?

YES>>

INSPECTION END

NO-1>>

More than the Reference: GO TO 18.

NO-2>>

Less than the Reference: GO TO 25.

DETECT MALFUNCTIONING PART

  1. Check for the cause of large engine friction. Refer to the following.

    • Engine oil level is too high

    • Engine oil viscosity

    • Belt tension of power steering, alternator, A/C compressor, etc. is excessive

    • Noise from engine

    • Noise from transmission, etc.

  2. Check for the cause of insufficient combustion. Refer to the following.

    • Valve clearance malfunction

    • Intake valve timing control function malfunction

    • Camshaft sprocket installation malfunction, etc.

>>

Repair or replace malfunctioning part, and then GO TO 30.

CHECK INTAKE SYSTEM

Check for the cause of uneven air flow through mass air flow sensor. Refer to the following.

  • Crushed air ducts

  • Malfunctioning seal of air cleaner element

  • Uneven dirt of air cleaner element

  • Improper specification of intake air system

Is the inspection result normal?

YES>>

GO TO 21.

NO>>

Repair or replace malfunctioning part, and then GO TO 20.

CHECK “A/F ALPHA-B1”, “A/F ALPHA-B2”, AND “B/FUEL SCHDL”

With CONSULT

Select “A/F ALPHA-B1”, “A/F ALPHA-B2”, and “B/FUEL SCHDL” at “Reference” of “Data Monitor” mode, and make sure that the indication is within the Reference.

Is the measurement value within the Reference?

YES>>

INSPECTION END

NO>>

“B/FUEL SCHDL” is more, “A/F ALPHA-B1”, “A/F ALPHA-B2” are less than the Reference: GO TO 21.

DISCONNECT AND RECONNECT MASS AIR FLOW SENSOR HARNESS CONNECTOR

  1. Stop the engine.

  2. Disconnect mass air flow sensor harness connector. Check pin terminal and connector for damage and then reconnect it again.

>>

GO TO 22.

CHECK “A/F ALPHA-B1” AND “A/F ALPHA-B2”

With CONSULT

  1. Start engine.

  2. Select “A/F ALPHA-B1” and “A/F ALPHA-B2” at “Reference” of “Data Monitor” mode, and make sure that the indication is within the Reference.

Is the measurement value within the Reference?

YES>>

Detect malfunctioning part of mass air flow sensor circuit and repair it. Refer to Diagnosis Procedure. Then GO TO 29.

NO>>

GO TO 23.

CHECK “MASS AIR FLOW SENSOR (Hz)”

With CONSULT

Select “MASS AIR FLOW SENSOR (Hz)” at “Reference” of “Data Monitor” mode, and make sure that the indication is within the Reference.

Is the measurement value within the Reference?

YES>>

GO TO 24.

NO>>

More than the Reference: Replace malfunctioning mass air flow sensor, and then GO TO 29.

REPLACE ECM

  1. Replace ECM. Refer to Removal and Installation.

  2. Proceed to Description.

>>

GO TO 29.

CHECK INTAKE SYSTEM

Check for the cause of uneven air flow through mass air flow sensor. Refer to the following.

  • Crushed air ducts

  • Malfunctioning seal in air cleaner element

  • Uneven dirt in air cleaner element

  • Improper specification in intake air system

Is the inspection result normal?

YES>>

GO TO 27.

NO>>

Repair or replace malfunctioning part, and then GO TO 26.

CHECK “B/FUEL SCHDL”

With CONSULT

Select “B/FUEL SCHDL” at “Reference” of “Data Monitor” mode, and make sure that the indication is within the Reference.

Is the measurement value within the Reference?

YES>>

INSPECTION END

NO>>

Less than the Reference: GO TO 27.

CHECK “MASS AIR FLOW SENSOR (Hz)”

With CONSULT

Select “MASS AIR FLOW SENSOR (Hz)” at “Reference” of “Data Monitor” mode, and make sure that the indication is within the Reference.

Is the measurement value within the Reference?

YES>>

GO TO 28.

NO>>

Less than the Reference: Replace malfunctioning mass air flow sensor, and then GO TO 30.

CHECK INTAKE SYSTEM

Check for the cause of air leak after the mass air flow sensor. Refer to the following.

  • Disconnection, looseness, and cracks in air duct

  • Looseness of oil filler cap

  • Disconnection of oil level gauge

  • Open stuck, breakage, hose disconnection, or cracks in PCV valve

  • Disconnection or cracks in EVAP purge hose, stuck open EVAP canister purge volume control solenoid valve

  • Malfunctioning seal in rocker cover gasket

  • Disconnection, looseness, or cracks in hoses, such as a vacuum hose, connecting to intake air system parts

  • Malfunctioning seal in intake air system, etc.

>>

GO TO 30.

CHECK “A/F ALPHA-B1”, “A/F ALPHA-B2”, AND “B/FUEL SCHDL”

With CONSULT

Select “A/F ALPHA-B1”, “A/F ALPHA-B2”, and “B/FUEL SCHDL” at “Reference” of “Data Monitor” mode, and make sure that the indication is within the Reference.

Is the measurement value within the Reference?

YES>>

INSPECTION END

NO>>

Detect malfunctioning part according to Symptom Table.

CHECK “B/FUEL SCHDL”

With CONSULT

Select “B/FUEL SCHDL” at “Reference” of “Data Monitor” mode, and make sure that the indication is within the Reference.

Is the measurement value within the Reference?

YES>>

INSPECTION END

NO>>

Detect malfunctioning part according to Symptom Table.

Power Supply and Ground Circuit Nissan Pathfinder 5th Gen

Ecm Diagnosis Procedure

CHECK FUSE

  1. Turn ignition switch OFF.

  2. Check that the following fuse is not blowing.

    Location Fuse No. Capacity
    IPDM E/R #79 15A
    #81 15A
    Fuse, fusible link and relay box #87 15A

Is the fuse blown (open)?

YES>>

Replace the fuse after repairing the applicable circuit.

NO>>

GO TO 2.

CHECK GROUND CONNECTION

Check ground connection E9. Refer to Ground Inspection in Circuit Inspection.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace error-detected parts.

CHECK ECM GROUND CIRCUIT

  1. Disconnect ECM harness connectors.

  2. Check the continuity between ECM harness connector and ground.

    ECM — Continuity
    Connector Terminal
    F78 3 Ground Existed
    F79 87
    E32 199
    201
    204
  3. Also check harness for short to power.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts.

CHECK IGNITION SWITCH SIGNAL

Check the voltage between ECM harness connectors as follows.

ECM Condition Voltage
Connector + −
Terminal
E32 185 204 Ignition switch: ON Battery voltage
Ignition switch: OFF 0 V

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

GO TO 5.

CHECK IGNITION SWITCH SIGNAL CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connectors.

  3. Disconnect IPDM E/R harness connector.

  4. Check the continuity between IPDM E/R harness connector and ECM harness connector.

    IPDM E/R ECM Continuity
    Connector Terminal Connector Terminal
    E121 43 E32 185 Existed
  5. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES>>

Perform trouble diagnosis for power supply circuit.

NO>>

Repair or replace error-detected parts.

CHECK ECM POWER SUPPLY

  1. Reconnect ECM harness connectors.

  2. Check the voltage between ECM harness connector terminals as follows.

    ECM Condition Voltage
    Connector + −
    Terminal
    E32 197 204 Ignition switch: ON Battery voltage
    • Ignition switch: OFF

    • More than a few seconds after turning ignition switch OFF

    0 V

Is the inspection result normal?

YES>>

GO TO 11.

NO>>

GO TO 7.

CHECK ECM POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connectors.

  3. Disconnect IPDM E/R harness connector.

  4. Check the continuity between IPDM E/R harness connector and ECM harness connector.

    IPDM E/R ECM Continuity
    Connector Terminal Connector Terminal
    F24 73 E32 197 Existed
  5. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair or replace error-detected parts.

CHECK ECM RELAY CONTROL SIGNAL

  1. Reconnect ECM harness connectors.

  2. Reconnect IPDM E/R harness connectors.

  3. Turn ignition switch ON.

  4. Turn ignition switch OFF and wait at least 10 seconds.

  5. Check the voltage between ECM harness connectors as follows.

    ECM Condition Voltage
    + −
    Connector Terminal Connector Terminal
    F79 140 E32 204
    • Ignition switch: OFF

    • A few seconds after turning ignition switch OFF

    0 − 1.0 V
    • Ignition switch: OFF

    • More than a few seconds after turning ignition switch OFF

    Battery voltage

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

GO TO 9.

CHECK ECM RELAY CONTROL SIGNAL CIRCUIT

  1. Disconnect ECM harness connectors.

  2. Disconnect IPDM E/R harness connector.

  3. Check the continuity between IPDM E/R harness connector and ECM harness connector.

    IPDM E/R ECM Continuity
    Connector Terminal Connector Terminal
    E78 93 F79 140 Existed
  4. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair or replace error-detected parts.

CHECK POWER SUPPLY CIRCUIT

Perform trouble diagnosis for power supply circuit.

Is the inspection result normal?

YES>>

Replace IPDM E/R. Refer to Removal and Installation.

NO>>

Repair or replace error-detected parts.

CHECK ECM POWER SUPPLY (BACK-UP)

  1. Turn ignition switch OFF.

  2. Check the voltage between ECM harness connectors as follows.

    ECM Condition Voltage
    + −
    Connector Terminal Connector Terminal
    F79 170 E32 204 Ignition switch: OFF Battery voltage

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Repair or replace error-detected parts.

Electric Intake Valve Timing Control Module Diagnosis Procedure

CHECK FUSE

  1. Turn ignition switch OFF.

  2. Check that the following fuse is not blowing.

    Location Fuse No. Capacity
    IPDM E/R #81 15A

Is the fuse blown (open)?

YES>>

Replace the fuse after repairing the applicable circuit.

NO>>

GO TO 2.

CHECK FUSIBLE LINK

Check that the following fusible link is not blowing.

Fusible link No. Capacity
#K 50A
#I 50A

Is the fusible link blown (open)?

YES>>

Replace the fusible link after repairing the applicable circuit.

NO>>

GO TO 3.

CHECK GROUND CONNECTION

Check ground connection E9. Refer to Ground Inspection in Circuit Inspection.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts.

CHECK ELECTRIC INTAKE VALVE TIMING CONTROL MODULE GROUND CIRCUIT

  1. Disconnect electric intake valve timing control module harness connectors.

  2. Check the continuity between electric intake valve timing control module harness connector and ground.

    Electric intake valve timing control module — Continuity
    Connector Terminal
    E11 3 Ground Existed
  3. Also check harness for short to power.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace error-detected parts.

CHECK ELECTRIC INTAKE VALVE TIMING CONTROL MODULE POWER SUPPLY

  1. Reconnect electric intake valve timing control module harness connectors.

  2. Check the voltage between electric intake valve timing control module harness connector terminals as follows.

    Electric intake valve timing control module Voltage
    Connector + −
    Terminal
    E11 1 3 Battery voltage
    2

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Perform trouble diagnosis for power supply circuit.

CHECK IGNITION SWITCH SIGNAL

Check the voltage between electric intake valve timing control module harness connectors as follows.

Electric intake valve timing control module Condition Voltage
+ −
Connector Terminal Connector Terminal
F99 95 E11 3 Ignition switch: ON Battery voltage
Ignition switch: OFF 0 V

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

GO TO 7.

CHECK IGNITION SWITCH SIGNAL

  1. Turn ignition switch OFF.

  2. Disconnect electric intake valve timing control module harness connectors.

  3. Disconnect IPDM E/R harness connector.

  4. Check the continuity between IPDM E/R harness connector and electric intake valve timing control module harness connector.

    IPDM E/R Electric intake valve timing control module Continuity
    Connector Terminal Connector Terminal
    E121 43 F99 95 Existed
  5. Also check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

Perform trouble diagnosis for power supply circuit.

NO>>

Repair or replace error-detected parts.

Fuel Pump Control Module (fpcm) Diagnosis Procedure

CHECK FUSE

  1. Turn ignition switch OFF.

  2. Check that the following fuse is not blowing.

    Location Fuse No. Capacity
    IPDM E/R #85 20A

Is the fuse blown (open)?

YES>>

Replace the fuse after repairing the applicable circuit.

NO>>

GO TO 2.

CHECK GROUND CONNECTION

Check ground connection B19. Refer to Ground Inspection in Circuit Inspection.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace ground connection.

CHECK FPCM GROUND CIRCUIT FOR OPEN AND SHORT

  1. Disconnect FPCM harness connectors.

  2. Check the continuity between FPCM harness connector and ground.

    FPCM — Continuity
    Connector Terminal
    B58 4 Ground Existed
  3. Also check harness for short to power.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts.

CHECK FPCM POWER SUPPLY

  1. Turn ignition switch ON.

  2. Check the voltage between FPCM harness connector terminals.

    FPCM Voltage
    Connector + −
    Terminal
    B58 1 4 Battery voltage

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

GO TO 5.

CHECK FPCM POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect FPCM harness connectors.

  3. Disconnect IPDM E/R harness connectors.

  4. Check the continuity between IPDM E/R harness connector and FPCM harness connector.

    IPDM E/R FPCM Continuity
    Connector Terminal Connector Terminal
    E121 46 B58 1 Existed
  5. Also check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace error-detected parts.

CHECK FUEL PUMP RELAY SIGNAL

  1. Reconnect IPDM E/R harness connectors.

  2. Turn ignition switch ON.

  3. Check the voltage between ECM harness connectors.

    ECM Voltage
    + −
    Connector Terminal Connector Terminal
    F78 84 E32 204 0 − 1.0 V

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

GO TO 7.

CHECK FUEL PUMP RELAY SIGNAL CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connectors.

  3. Disconnect IPDM E/R harness connectors.

  4. Check the continuity between IPDM E/R harness connector and ECM harness connector.

    IPDM E/R ECM Continuity
    Connector Terminal Connector Terminal
    F24 76 F78 84 Existed
  5. Also check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair or replace error-detected parts.

CHECK POWER SUPPLY CIRCUIT

Perform trouble diagnosis for power supply circuit.

Is the inspection result normal?

YES>>

Replace IPDM E/R. Refer to Removal and Installation.

NO>>

Repair or replace error-detected parts.