Driveline - Rear Final Drive: R145
- Precautions
- Preparation
- System Description. Structure and Operation
- Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting
- Periodic Maintenance. Rear Differential Gear Oil
- Unit Removal and Installation. Rear Final Drive Assembly
- Service Data and Specifications (SDS)
Precautions Nissan Pathfinder Fifth generation
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER"
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collisions.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” sections of this Service Manual.
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision that would result in air bag inflation, it is recommended that all maintenance and repair be performed by an authorized NISSAN/INFINITI dealer.
Improper repair, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module, see “SRS AIR BAG”.
Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the ignition/power switch ON or engine running, never use air or electric power tools or strike near the sensor(s) with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing serious injury.
When using air or electric power tools or hammers, always switch the ignition/power switch OFF, disconnect the 12V battery or batteries, and wait at least 3 minutes before performing any service.
Service Notice or Precautions for Rear Final Drive
Use recommended gear oil only, refer to Fluids and Lubricants (For USA and Canada) or Fluids and Lubricants (For Mexico).
Use only genuine NISSAN parts for electro-hydraulic coupling oil.
Check for the correct installation status prior to removal or disassembly. If matching marks are required, be certain they never interfere with the function of the parts when applied.
Overhaul should be done in a clean work area, it is preferable to work in dustproof area.
Before disassembly, using steam or white gasoline, completely remove sand and mud from the exterior of the unit, preventing them from entering into the unit during disassembly or assembly.
Check appearance of the disassembled parts for damage, deformation, and unusual wear. Replace them with a new one if necessary.
Seals should be replaced any time when the unit is disassembled.
In principle, tighten bolts or nuts gradually in several steps working diagonally from inside to outside. If tightening sequence is specified, observe it.
Clean and flush the parts sufficiently and blow-dry them.
Be careful not to damage sliding surfaces and mating surfaces.
When applying sealant, remove the old sealant from the mounting surface; then remove any moisture, oil, and foreign materials from the application and mounting surfaces.
Always use shop paper for cleaning the inside of components.
Avoid using cotton gloves or shop rags to prevent entering of lint.
During assembly, observe the specified tightening torque, and apply new gear oil, petroleum jelly, or multi-purpose grease as specified for each Nissan Pathfinder vehicle, if necessary.
Preparation Nissan Pathfinder 2022
Special Service Tools
The actual shape of the tools may differ from those illustrated here.
Tool number (TechMate No.) Tool name | Description | |
|---|---|---|
ST30720000 (NI-25405) Drift |
![]() |
Installing front oil seal a: 77 mm (3.03 in) dia.b: 55 mm (2.185 in) dia. |
KV40105740 ( — ) Drift |
![]() |
Installing side oil seal (cover side) a: 57 mm (2.24 in) dia.b: 48 mm (1.89 in) dia. |
KV31103000 (NI-38982) Drift |
![]() |
Installing side oil seal (carrier side) a: 70 mm (2.76 in) dia.b: 59 mm (2.32 in) dia.c: 49 mm (1.93 in) dia. |
ST35325000 ( — ) Drift bar |
![]() |
Installing side oil seal (carrier side) |
— (NI-53123) Park lock tool |
![]() |
Placing transaxle in neutral |
Commercial Service Tools
| Tool name | Description | |
|---|---|---|
| Power tool | ![]() |
Loosening nuts, screws and bolts |
Lubricant or/and Sealant
| Item | Use |
|---|---|
| Electro-hydraulic coupling oil (Genuine NISSAN part) | Filling when the parts of electro-hydraulic coupling assembly and/or rear final drive assembly is disassembled |
| Red lead or equivalent | Checking tooth contact |
Always Replace with New Parts
| Never Reuse These Parts | Part # Prefix | For additional information: |
|---|---|---|
| Hose clamp | 38322BA | REAR FINAL DRIVE ASSEMBLY EXPLODED VIEW |
| Breather tube | 38322A | REAR FINAL DRIVE ASSEMBLY EXPLODED VIEW |
| O-ring | 38250E | REAR FINAL DRIVE ASSEMBLY EXPLODED VIEW |
| Nut | 55011BC | REAR FINAL DRIVE ASSEMBLY EXPLODED VIEW |
| Breather | 38322 | REAR FINAL DRIVE ASSEMBLY EXPLODED VIEW |
| Companion flange lock nut | 38351D | ELECTRO-HYDRAULIC COUPLING EXPLODED VIEW |
| Companion flange | 38761 | ELECTRO-HYDRAULIC COUPLING EXPLODED VIEW |
| Electro-hydraulic coupling oil seal | 38765F | ELECTRO-HYDRAULIC COUPLING EXPLODED VIEW |
| O-ring | 38334 | ELECTRO-HYDRAULIC COUPLING EXPLODED VIEW |
| Plug | 38351F | ELECTRO-HYDRAULIC COUPLING EXPLODED VIEW |
| Side oil seal | 38342 | ELECTRO-HYDRAULIC COUPLING EXPLODED VIEW |
| Stud | 38351C | ELECTRO-HYDRAULIC COUPLING EXPLODED VIEW |
| Filler plug | 38351F | ELECTRO-HYDRAULIC COUPLING EXPLODED VIEW |
| Bolt | 38300A | ELECTRO-HYDRAULIC COUPLING EXPLODED VIEW |
System Description. Structure and Operation Nissan Pathfinder 2022
Sectional View

| 1. | Side oil seal | 2. | Differential case | 3. | Drive pinion |
| 4. | Electro-hydraulic coupling | 5. | Companion flange | 6. | Actuator assembly |
Electro-Hydraulic Coupling
The electro-hydraulic coupling operates as the 4WD system. For the operation, refer to Operation Description.
Symptom Diagnosis. Noise, Vibration and Harshness (nvh) Troubleshooting Nissan Pathfinder 2026
NVH Troubleshooting Chart
Use the chart below to find the cause of the symptom. If necessary, repair or replace these parts.
| Possible cause and SUSPECTED PARTS | Symptom | Reference | |
|---|---|---|---|
| Noise | Vibration | ||
| Gear tooth rough | X | — | Refer to Inspection |
| Gear contact improper | X | — | — |
| Tooth surfaces worn | X | — | Refer to Inspection |
| Backlash incorrect | X | — | — |
| Companion flange excessive runout | X | — | — |
| Gear oil improper | X | — | Refer to Inspection |
| PROPELLER SHAFT | X | — | Refer to NVH Troubleshooting Chart |
| AXLE AND SUSPENSION | X | — | Refer to NVH Troubleshooting Chart Refer to NVH Troubleshooting Chart Refer to NVH Troubleshooting Chart Refer to NVH Troubleshooting Chart |
| TIRE | X | — | Refer to NVH Troubleshooting Chart |
| ROAD WHEEL | X | — | Refer to NVH Troubleshooting Chart |
| DRIVE SHAFT | X | — | Refer to NVH Troubleshooting Chart Refer to NVH Troubleshooting Chart |
| BRAKE | X | — | Refer to NVH Troubleshooting Chart |
| STEERING | X | — | Refer to NVH Troubleshooting Chart |
| Electro-hydraulic coupling | X | X | Refer to Removal and Installation |
×: Applicable
Periodic Maintenance. Rear Differential Gear Oil Nissan Pathfinder 2022
Inspection
REAR DIFFERENTIAL GEAR OIL LEAKS
Check that rear differential gear oil is not leaking from the final drive assembly or around it.
REAR DIFFERENTIAL GEAR OIL LEVEL
Remove and discard filler plug (1).

| : Front |
Rear differential gear oil level should be level with the bottom of the filler plug hole. Add rear differential gear oil if necessary. Refer to Fluids and Lubricants (United States and Canada) or Fluids and Lubricants (Mexico).
Install filler plug (1) and tighten to the specified torque. Refer to Exploded View.
Draining
Remove and discard drain plug (1), and drain rear differential gear oil.

| : Front |
Install drain plug (1) and tighten to the specified torque. Refer to Exploded View.
Refilling
Remove and discard filler plug (1).

| : Front |
Fill with new rear differential gear oil to the specified level near the filler plug hole.
| Rear differential gear oil grade and viscosity | : Refer to Fluids and Lubricants (United States and Canada) or Fluids and Lubricants (Mexico). |
| Rear differential gear oil capacity | : Refer to General Specification. |
Install filler plug (1) and tighten to specified torque. Refer to Exploded View.
Unit Removal and Installation. Rear Final Drive Assembly Nissan Pathfinder 5th Gen
Exploded View

| 1. | Plug | 2. | Breather hose | 3. | Hose clamp |
| 4. | Breather tube | 5. | O-ring | 6. | Final drive assembly |
| 7. | Breather | 8. | Bolt | 9. | Final drive assembly bracket |
| Clip | Front |
Removal and Installation
REMOVAL
Drain rear differential gear oil. Refer to Draining.
Remove rear wheel hub (LH/RH). Refer to Removal and Installation.
Remove the rear propeller shaft from the final drive assembly and support the rear propeller shaft with suitable wire. Refer to Removal and Installation.
Remove the Nissan Pathfinder vehicle spare tire.
Remove rear stabilizer bar. Refer to Removal and Installation.
Remove 4WD harness bracket.
Disconnect the harness connector from 4WD control unit.
Remove breather hose from breather tube.
Support rear final drive assembly with a suitable jack.
Remove final drive bracket bolts.
Remove rear final drive nut (
) at rear suspension member, and remove rear final drive from Nissan Pathfinder vehicle.

INSTALLATION
Installation is in the reverse order of removal.
When oil leaks while removing rear final drive assembly, check oil level after the installation. Refer to Inspection.
If replacing rear final drive assembly, perform "ADDITIONAL SERVICE WHEN REPLACING REAR FINAL DRIVE ASSEMBLY". Refer to Description.
Service Data and Specifications (SDS) Nissan Pathfinder R53
General Specification
| Applied model | 4WD | ||||||
|---|---|---|---|---|---|---|---|
| VQ35DD | |||||||
| 9AT | |||||||
| Final drive model | R145 | ||||||
| Gear ratio | 2.466 | ||||||
| Number of teeth (Drive gear/Drive pinion) | 37/15 | ||||||
| Oil type | Refer to Fluids and Lubricants (United States and Canada) or Fluids and Lubricants (Mexico). | ||||||
| Final drive oil capacity (Approx.) | 0.45 (1, 3/4) | ||||||
| Electro-hydraulic coupling oil capacity (Approx.) | 0.69 (1–1/2, 1–1/4) | ||||||
| Number of pinion gears | 2 | ||||||





