Exterior Lighting System - Dtc/circuit Diagnosis

In this manual: Exterior Lighting System - Dtc/circuit Diagnosis
General Information — 8Engine :: Engine Mechanical — 19Engine Lubrication System - Precautions. Preparation — 1Engine Lubrication System - Lubrication System (System Description). Engine Oil Pressure (Basic Inspection). Service Data and Specifications (SDS) — 1Engine Cooling System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Engine Cooling System - Engine Coolant — 1Engine Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Engine Control System - Ecu Diagnosis Information — 1Ecu Diagnosis Information - Ecm ++ — 1Engine Control System - Basic Inspection — 1Basic Inspection - Diagnosis and Repair Workflow ++ — 1Basic Inspection - Basic Inspection ++ — 1Basic Inspection - Additional Service When Replacing Ecm ++ — 1Basic Inspection - Fuel Pressure Check ++ — 1Basic Inspection - How to Set Srt Code ++ — 1Basic Inspection - How to Erase Permanent Dtc ++ — 1Engine Control System - Dtc/circuit Diagnosis — 1Engine Control System - Symptom Diagnosis — 1Engine Control System - Periodic Maintenance — 1Engine Control System - Removal and Installation — 1Fuel System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Fuel System - Fuel System (Periodic Maintenance). Fuel Level Sensor Unit (Disassembly and Assembly) — 1Exhaust System - Precautions. Preparation — 1Exhaust System - Exhaust System (Periodic Maintenance). Exhaust System (Removal and Installation) — 1Starting System - Precautions. Preparation. Starter Motor (Service Data and Specifications (sds)) — 1Starting System - Diagnosis and Repair Work Flow — 1Starting System - Starting System (Symptom Diagnosis). Starter Motor (Removal and Installation) — 1Accelerator Control System - Precautions. Service Data and Specifications (SDS) — 1Accelerator Control System - Accelerator Pedal Assembly — 1Transmission & Driveline :: Transaxle & Transmission — 21Driveline - System Description — 1Transfer: Ty92b - Ecu Diagnosis Information. Awd Control Unit ++ — 1Driveline - Basic Inspection — 1Driveline - Dtc/circuit Diagnosis — 1Driveline - Symptom Diagnosis — 1Driveline - Removal and Installation — 1Transfer: Ty92b - Unit Removal and Installation. Transfer Assembly ++ — 1Driveline - Unit Disassembly and Assembly — 1Driveline - Basic Inspection — 1Driveline - Removal and Installation — 1Driveline - Unit Disassembly and Assembly — 1Front Axle - Precautions. Preparation — 1Front Axle - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Front Axle - Front Drive Shaft Boot — 1Front Axle - Front Drive Shaft — 1Rear Axle - Precautions. Preparation. Service Data and Specifications (SDS) — 1Rear Axle - Noise, Vibration and Harshness (nvh) Troubleshooting — 1Rear Axle - Rear Drive Shaft — 1Suspension :: Front Suspension — 7Rear Suspension - Precautions. Preparation — 1Rear Suspension - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Rear Suspension - Rear Suspension Assembly — 1Road Wheels & Tires - Precautions — 1Road Wheels & Tires - Preparation. Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Road Wheels & Tires - System — 1Brakes :: Brake System — 9Parking Brake System - Precautions. Preparation — 1Parking Brake System - System — 1Vdc/tcs/abs - Precautions ++ — 1Brake Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Dtc/circuit Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Steering :: Steering System — 9Steering Control System - Precautions — 1Steering Control System - System — 1Steering Control System - Eps Control Unit (Ecu Diagnosis Information. Removal and Installation) — 1Restraints :: Seat Belt — 7Srs Air Bag - Precautions. Preparation — 1Srs Air Bag - Collision Diagnosis — 1Srs Air Bag - Occupant Classification System — 1Srs Air Bag Control System - Precautions — 1Srs Air Bag Control System - System — 1Srs Air Bag Control System - Diagnosis Sensor Unit — 1Srs Air Bag Control System - Inspection and Adjustment — 1Ventilation, Heater & Air Conditioner :: Ventilation System — 6Heater & Air Conditioning System - Precautions — 1Heater & Air Conditioning System - Preparation — 1Heater & Air Conditioning System - Component Parts — 1Heater & Air Conditioning System - Diagnosis and Repair Work Flow — 1Heater & Air Conditioning System - Compressor — 1Heater & Air Conditioning System - Cooler Pipe and Hose — 1Heater & Air Conditioning System - Condenser. Condenser — 1Heater & Air Conditioning System - Heating and Cooling Unit Assembly — 1Heater & Air Conditioning System - Service Data and Specifications (SDS) — 1Heater & Air Conditioning Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1Heater & Air Conditioning Control System - Ecu Diagnosis Information — 1Heater & Air Conditioning Control System - Basic Inspection — 1Heater & Air Conditioning Control System - Dtc/circuit Diagnosis — 1Heater & Air Conditioning Control System - Symptom Diagnosis — 1Heater & Air Conditioning Control System - Removal and Installation — 1Body Interior :: Interior — 8Instrument Panel - Precautions. Preparation. Clip List — 1Instrument Panel - Squeak and Rattle Trouble Diagnoses — 1Instrument Panel - Cluster Lid C — 1Seat - Precautions — 1Seat - Preparation. Clip List — 1Seat - Component Parts — 1Seat - System — 1Seat - Diagnosis and Repair Work Flow — 1Seat - Front Seat — 1Seat - Second Row Seats — 1Seat - Third Row Seats — 1Seat - Front Seat — 1Seat - Second Row Seat — 1Seat - Third Row Seat — 1Automatic Drive Positioner - Precautions. Preparation — 1Automatic Drive Positioner - System — 1Automatic Drive Positioner - Diagnosis and Repair Work Flow — 1Automatic Drive Positioner - Inspection and Adjustment — 1Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock — 38Security Control System - Precautions — 1Security Control System - System — 1Security Control System - Ecm, Bcm, Intelligent Key Unit, Ipdm E/r — 1Security Control System - Vehicle Security System Cannot Be Set — 1Glass & Window System - Precautions. Preparation — 1Glass & Window System - Squeak and Rattle Trouble Diagnoses — 1Power Window Control System - Precautions. Preparation — 1Power Window Control System - Power Supply and Ground Circuit — 1Power Window Control System - Power Window Motor Circuit — 1Power Window Control System - Front Power Window Rh Alone Does Not Operate — 1Power Window Control System - Rear Lh Side Power Window Alone Does Not Operate — 1Power Window Control System - Rear Rh Side Power Window Alone Does Not Operate — 1Roof - Precautions. Preparation — 1Roof - Power Supply and Ground Circuit — 1Roof - Moonroof Switch Assembly — 1Roof - Lin Communication Circuit — 1Roof - Auto Operation Does Not Operate — 1Roof - Anti-Pinch Function Does Not Operate — 1Exterior - Precautions. Preparation. Clip List (Preparation) — 1Exterior - Squeak and Rattle Trouble Diagnoses — 1Exterior - Fender Protector — 1Exterior - Over Fender — 1Exterior - Under Cover — 1Exterior - Roof Side Rail — 1Body Repair - Service Information — 1Service Information - Sheet Metal Work ++ — 1Service Information - Body Welding and Precautions ++ — 1Service Information - Safety and Health ++ — 1Service Information - Repairing Procedures and Precautions ++ — 1Body Repair - Precaution — 1Body Repair - Preparation — 1Body Repair - Removal and Installation — 1Driver Controls :: Mirrors — 8Exterior Lighting System - System Description — 1System Description - Component Parts ++ — 1Exterior Lighting System - Basic Inspection — 1Exterior Lighting System - Dtc/circuit Diagnosis — 1Exterior Lighting System - Symptom Diagnosis — 1Exterior Lighting System - Periodic Maintenance — 1Exterior Lighting System - Removal and Installation — 1Interior Lighting System - Precautions. Preparation — 1Interior Lighting System - Component Parts. Interior Lighting System — 1Interior Lighting System - System — 1Interior Lighting System - Diagnosis and Repair Work Flow — 1Interior Lighting System - Interior Lighting System Symptoms (Symptom Diagnosis). Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Interior Lighting System - Foot Lamp — 1Wiper & Washer - Precautions — 1Wiper & Washer - Preparation. Bcm, Ipdm E/r (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Wiper & Washer - System — 1Wiper & Washer - Diagnosis and Repair Work Flow — 1Defogger - Precautions. Bcm, A/c Auto Amp. (Ecu Diagnosis Information) — 1Defogger - Diagnosis and Repair Work Flow — 1Horn - Precautions — 1Electrical & Power Control :: Power Outlet — 13Body Control System - Precautions. Preparation — 1Body Control System - Component Parts — 1Body Control System - System — 1Body Control System - Diagnosis System (bcm) — 1Body Control System - Bcm — 1Lan System - System Description — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - Removal and Installation — 1Charging System - Precautions. Preparation. Ecm, Ipdm E/r (Ecu Diagnosis Information) — 1Charging System - Diagnosis and Repair Work Flow — 1Charging System - Charging System (Symptom Diagnosis). Generator (Removal and Installation). Service Data and Specifications (SDS) — 1Power Supply, Ground & Circuit Elements - Precautions. Preparation. Service Data and Specifications (SDS) — 1Driver Information & Multimedia :: Meter, Warning Lamp & Indicator — 25Warning Chime System - Application Notice (How to Use This Manual). Precautions — 1Warning Chime System - System — 1Warning Chime System - Diagnosis System (combination Meter) — 1Warning Chime System - Bcm, Combination Meter (Ecu Diagnosis Information). Diagnosis and Repair Work Flow (Basic Inspection) — 1Sonar System - Precautions. Preparation — 1Sonar System - Sonar Control Unit — 1Dtc/circuit Diagnosis - B2720 Corner Sensor [rl] ++ — 1Audio, Visual & Navigation System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Multi Av (av Control Unit) ++ — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Symptom Diagnosis - Multi Av System ++ — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Cruise Control & Driver Assistance :: Cruise Control System — 17Driver Assistance System - System Description — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Driver Assistance System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1System Description - Handling Precaution ++ — 1Driver Assistance System - Ecu Diagnosis Information — 1Driver Assistance System - Basic Inspection — 1Basic Inspection - Distance Sensor Alignment ++ — 1Basic Inspection - Camera Aiming Adjustment ++ — 1Basic Inspection - Action Test ++ — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Laser/radar (distance Sensor) ++ — 1Dtc/circuit Diagnosis - Lane Camera (front Camera Unit) ++ — 1Driver Assistance System - Symptom Diagnosis — 1Driver Assistance System - Removal and Installation — 1Driver Assistance System - System Description — 1System Description - System ++ — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Drive Mode System - Precautions — 1Drive Mode System - Component Parts. Drive Mode System — 1Drive Mode System - System — 1Drive Mode System - Diagnosis and Repair Work Flow — 1Drive Mode System - Drive Mode Select Switch Circuit — 1Maintenance - Precautions. Preparation — 1Maintenance - General Maintenance — 1Maintenance - Periodic Maintenance — 1Maintenance - Recommended Fluids and Lubricants — 1Maintenance - Engine Maintenance — 1Maintenance - Chassis and Body Maintenance — 1Engine Lubrication System - Periodic Maintenance — 1Engine Lubrication System - Removal and Installation — 1Engine Cooling System - System Description — 1Engine Cooling System - Removal and Installation — 1Engine Control System - Vq35dd — 1Fuel System - Removal and Installation — 1Starting System - System Description — 1Starting System - Dtc/circuit Diagnosis — 1Driveline - Transfer: Ty92b — 1Driveline - Rear Propeller Shaft: 3fcj-Cvj — 1Driveline - Rear Final Drive: R145 — 1Front Axle - Periodic Maintenance — 1Front Axle - Removal and Installation — 1Rear Axle - Periodic Maintenance — 1Rear Axle - Removal and Installation — 1Rear Suspension - Removal and Installation — 1Road Wheels & Tires - System Description — 1Road Wheels & Tires - Basic Inspection — 1Road Wheels & Tires - Dtc/circuit Diagnosis — 1Road Wheels & Tires - Symptom Diagnosis — 1Road Wheels & Tires - Periodic Maintenance — 1Road Wheels & Tires - Removal and Installation — 1Parking Brake System - System Description — 1Parking Brake System - Basic Inspection — 1Parking Brake System - Dtc/circuit Diagnosis — 1Parking Brake System - Symptom Diagnosis — 1Parking Brake System - Removal and Installation — 1Brake Control System - Vdc/tcs/abs — 1Brake Control System - Automatic Brake Hold — 1Brake Control System - Automatic Emergency Braking — 1Brake Control System - Rear Automatic Braking — 1Steering Control System - System Description — 1Steering Control System - Basic Inspection — 1Steering Control System - Dtc/circuit Diagnosis — 1Steering Control System - Symptom Diagnosis — 1Srs Air Bag - Removal and Installation — 1Srs Air Bag Control System - System Description — 1Srs Air Bag Control System - Basic Inspection — 1Srs Air Bag Control System - Symptom Diagnosis — 1Heater & Air Conditioning System - Symptom Diagnosis — 1Heater & Air Conditioning System - Periodic Maintenance — 1Heater & Air Conditioning Control System - Automatic Air Conditioning — 1Instrument Panel - Removal and Installation — 1Instrument Panel - Unit Disassembly and Assembly — 1Seat - Ecu Diagnosis Information — 1Seat - Dtc/circuit Diagnosis — 1Seat - Symptom Diagnosis — 1Automatic Drive Positioner - System Description — 1Automatic Drive Positioner - Ecu Diagnosis Information — 1Automatic Drive Positioner - Dtc/circuit Diagnosis — 1Automatic Drive Positioner - Symptom Diagnosis — 1Automatic Drive Positioner - Removal and Installation — 1Security Control System - System Description — 1Security Control System - Basic Inspection — 1Security Control System - Dtc/circuit Diagnosis — 1Security Control System - Symptom Diagnosis — 1Security Control System - Removal and Installation — 1Glass & Window System - Removal and Installation — 1Power Window Control System - System Description — 1Power Window Control System - Ecu Diagnosis Information — 1Power Window Control System - Basic Inspection — 1Power Window Control System - Dtc/circuit Diagnosis — 1Power Window Control System - Symptom Diagnosis — 1Power Window Control System - Removal and Installation — 1Roof - System Description — 1Roof - Ecu Diagnosis Information — 1Roof - Basic Inspection — 1Roof - Dtc/circuit Diagnosis — 1Roof - Symptom Diagnosis — 1Roof - Removal and Installation — 1Exterior - System Description — 1Exterior - Removal and Installation — 1Body Repair - Repair Information — 1Exterior Lighting System - Led Headlamp — 1Interior Lighting System - Dtc/circuit Diagnosis — 1Interior Lighting System - Removal and Installation — 1Wiper & Washer - System Description — 1Wiper & Washer - Dtc/circuit Diagnosis — 1Wiper & Washer - Symptom Diagnosis — 1Wiper & Washer - Removal and Installation — 1Defogger - System Description — 1Defogger - Dtc/circuit Diagnosis — 1Defogger - Symptom Diagnosis — 1Defogger - Removal and Installation — 1Horn - Removal and Installation — 1Body Control System - Basic Inspection — 1Body Control System - Dtc/circuit Diagnosis — 1Body Control System - Symptom Diagnosis — 1Body Control System - Removal and Installation — 1Lan System - Can Fundamental — 1Lan System - Can — 1Lan System - Can Gateway — 1Power Control System - Ipdm E/r — 1Power Control System - Power Distribution System — 1Charging System - System Description — 1Charging System - Dtc/circuit Diagnosis — 1Power Supply, Ground & Circuit Elements - System Description — 1Power Supply, Ground & Circuit Elements - Basic Inspection — 1Power Supply, Ground & Circuit Elements - Removal and Installation — 1Warning Chime System - System Description — 1Warning Chime System - Dtc/circuit Diagnosis — 1Warning Chime System - Symptom Diagnosis — 1Sonar System - System Description — 1Sonar System - Basic Inspection — 1Sonar System - Dtc/circuit Diagnosis — 1Sonar System - Symptom Diagnosis — 1Sonar System - Removal and Installation — 1Audio, Visual & Navigation System - Nissanconnect — 1Audio, Visual & Navigation System - Intelligent Around View Monitor System — 1Audio, Visual & Navigation System - Rear View Monitor System — 1Audio, Visual & Navigation System - Telematics System — 1Driver Assistance System - Adas Control Unit 2 — 1Driver Assistance System - Driver Assistance System — 1Driver Assistance System - Chassis Control — 1Drive Mode System - Removal and Installation — 1Dtc/circuit Diagnosis (C053c Wheel Speed Sensor ... U2141 Can Comm Circuit) — 1Dtc/circuit Diagnosis (P0011 Intake Valve Timing Control ... P0111 Iat Sensor) — 1Dtc/circuit Diagnosis (P0116 Engine Coolant Temperature Sensor ... P025b Fuel Pump Module a) — 1Dtc/circuit Diagnosis (P026b Injection Timing ... P0420 Three Way Catalyst Function) — 1Dtc/circuit Diagnosis (P0441 Evap Control System ... P0524 Engine Oil Pressure) — 1Dtc/circuit Diagnosis (P0532 A/c Refrigerant Pressure Sensor ... P064d Ecm) — 1Dtc/circuit Diagnosis (P06da Engine Oil Pressure Control Solenoid Valve ... P1217 Engine Over Temperature) — 1Dtc/circuit Diagnosis (P1220 Fuel Pump Control Module (fpcm) ... P1574 Ascd Vehicle Speed Sensor) — 1Dtc/circuit Diagnosis (P1575 Brake Switch ... P2101 Electric Throttle Control Function) — 1Dtc/circuit Diagnosis (P2118 Throttle Control Motor ... P34ac Electric Intake Valve Timing Control Actuator) — 1Dtc/circuit Diagnosis (Active Grille Shutter ... High Pressure Fuel Pump) — 1Dtc/circuit Diagnosis (Ignition Signal ... Variable Induction Air System) — 14012 C1040 Emergency Brake — 14013 C106a Wheel Sensor — 14014 C1078-55 Not Configuration — 14015 C10b4-98 Overheat — 14016 B1001 Lap Pre-Tensioner Lh — 14017 B0001 Driver Air Bag Module — 14018 B100e Knee Air Bag Module Rh — 14019 B142x Collision Detection — 1Dtc/circuit Diagnosis (B20c7-11 A/c Clutch ... B24a6-11 in-Vehicle Sensor) — 1Dtc/circuit Diagnosis (B24a6-15 in-Vehicle Sensor ... U2140-87 Can Comm Err (ecm)) — 1Dtc/circuit Diagnosis (C1f00-1c Control Unit ... C1f04-61 Brake Sw/stop Lamp Sw) — 1Dtc/circuit Diagnosis (C1f05-49 Front Camera Unit ... C1f70-87 Ethernet Circuit) — 1
189steps
~1134min
4/5difficulty
Done 0 of 189
  • B121a-11 Fr Fog Lamp Lh Pwr Sply Circ
  • B20a4-87 Headlamp (lh) Lin Communication
  • B20d4-11 Tail Lamp Lh Pwr Sply Circ
  • B20e3-96 Led Headlamp Lh
  • Front Side Marker Lamp Circuit
  • Tail Lamp Circuit
  • License Plate Lamp Circuit
  • Rear Side Marker Lamp Circuit
  • Stop Lamp Circuit
  • Back-Up Lamp Circuit
  • Front Fog Lamp Circuit
  • Turn Signal Lamp Circuit
  • Hazard Switch Circuit

B121a-11 Fr Fog Lamp Lh Pwr Sply Circ Nissan Pathfinder 2026

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC detection condition
B121A–11

FR FOG LAMP LH PWR SPLY CIRC

(Front fog lamp left hand power supply circuit)
[CIRCUIT SHORT TO GROUND] Diagnosis condition When front fog lamp ON conditions are satisfied (Smart FET inside IPDM E/R is ON)
Signal (terminal) Front fog lamp LH power supply circuit
Threshold Overcurrent is detected
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Harness or connector

  • Front fog lamp LH

    • LED

  • IPDM E/R

FAIL-SAFE

Shuts off the power supply to the front fog lamp LH power supply circuit until the front fog lamp ON conditions are no longer satisfied.

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

CONSULT

  1. Ignition switch ON.

  2. Select “Fr fog lamp (LH) circ malfunctn” in “Data Monitor” mode of “IPDM E/R”.

  3. Check the monitor status.

    Monitor itemMonitor status
    Fr fog lamp (LH) circ malfunctn 0
    1

What is the monitor status?

“0”>>

GO TO 2.

“1”>>

A short circuit is detected multiple times in the front fog lamp LH power supply circuit, and damage accumulates at the Smart FET inside the IPDM E/R. For this reason, IPDM E/R does not turn ON the Smart FET. Because the DTC cannot be reproduced in this state, perform DTC Diagnosis Procedure and replace IPDM E/R after the malfunctioning part is repaired. Refer to Removal and Installation.

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch OFF.

  2. Ignition switch ON.

  3. Turn lighting switch 2ND, and front fog lamp switch ON.

  4. Select “Self Diagnostic Result” mode of “IPDM E/R”.

  5. Check DTC.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK FRONT FOG LAMP LH POWER SUPPLY CIRCUIT (SHORT)

  1. Ignition switch OFF.

  2. Turn lighting switch OFF or AUTO, and front fog lamp switch OFF.

  3. Disconnect IPDM E/R connector and front fog lamp LH connector.

  4. Check continuity between IPDM E/R harness connector and ground.

    IPDM E/R—Continuity
    ConnectorTerminal
    E217 51 Ground No

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace harness.

CHECK FRONT FOG LAMP LH POWER SUPPLY

  1. Connect IPDM E/R connector.

  2. Ignition switch ON

  3. Turn lighting switch 2ND.

  4. With operating the front fog lamp switch, check voltage between front fog lamp LH harness connector and ground.

    +-Condition

    Voltage

    (Approx.)
    Front fog lamp LH
    ConnectorTerminal
    E305 2 Ground Front fog lamp switch ON Battery voltage
    OFF 0 V

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Replace IPDM E/R. Refer to Removal and Installation.

CHECK FRONT FOG LAMP LH

Check the front fog lamp LH. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace front fog lamp LH. Refer to Removal and Installation.

Component Inspection

CHECK FRONT FOG LAMP LH

  1. Ignition switch OFF.

  2. Disconnect front fog lamp LH connector.

  3. Check continuity between front fog lamp LH terminals.

    Front fog lamp LHContinuity
    Terminal
    +–
    2 1 Yes

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace front fog lamp LH. Refer to Removal and Installation.

B20a4-87 Headlamp (lh) Lin Communication Nissan Pathfinder 5th Gen

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC detection condition
B20A4–87

Headlamp (LH) LIN communication

[Headlamp (left hand) local interconnect network communication]
[MISSING MESSAGE] Diagnosis condition Ignition switch ON
Signal (terminal) Headlamp LH LIN communication
Threshold Detected headlamp LH LIN communication error
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Harness or connector

  • Front combination lamp LH

    • LED headlamp control module

    • Harness

  • IPDM E/R

FAIL-SAFE

  • Transmits the headlamp warning signal to the combination meter via CAN communication (when the ignition switch is placed ON, the headlamp warning is displayed on the information display of the combination meter).

  • Transmits the request signal to the both side LED headlamp control modules via LIN communication, and turns ON the headlamp (LO) and parking lamp.

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Select “Self Diagnostic Result” mode of “IPDM E/R”.

  3. Check DTC.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK SELF-DIAGNOSIS RESULT

CONSULT

  1. Ignition switch ON.

  2. Select “Self Diagnostic Result” mode of “IPDM E/R”.

  3. Check if DTC "B20A4–87" is displayed with DTC "B20A2–87".

Is applicable DTC detected?

YES>>

GO TO 2.

NO>>

GO TO 3.

CHECK HEADLAMP LH LIN COMMUNICATION CIRCUIT 1

  1. Ignition switch OFF.

  2. Disconnect the following connectors:

    • Front combination lamp RH

    • Front combination lamp LH

    • IPDM E/R

  3. Check continuity between front combination lamp LH harness connector and IPDM E/R harness connector.

    Front combination lamp LHIPDM E/RContinuity
    ConnectorTerminalConnectorTerminal
    E249 2 E119 38 Yes
  4. Check continuity between IPDM E/R harness connector and ground.

    IPDM E/R(-)Continuity
    ConnectorTerminal
    E119 38 Ground No

Is the inspection result normal?

YES>>

Replace IPDM E/R. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK HEADLAMP LH FUSE

  1. Ignition switch OFF.

  2. Check that the following fuse is not blown (open):

    UnitFuse No.Capacity
    Front combination lamp LH 88 15 A

Is the fuse blown (open)?

YES>>

Replace the blown (open) fuse after repairing the affected circuit if a fuse is blown (open).

NO>>

GO TO 4.

CHECK HEADLAMP LH POWER SUPPLY

  1. Disconnect front combination lamp LH connector.

  2. Check voltage between front combination lamp LH harness connector and ground.

    (+)(-)

    Voltage

    (Approx.)
    Front combination lamp LH
    ConnectorTerminal
    E249 1 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace harness.

CHECK HEADLAMP LH GROUND CIRCUIT

Check continuity between front combination lamp LH harness connector and ground.

Front combination lamp LH(-)Continuity
ConnectorTerminal
E249 6 Ground Yes

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace harness.

CHECK HEADLAMP LH CONTROL SIGNAL

  1. Ignition switch ON.

  2. Check voltage between front combination lamp LH harness connector and ground.

    (+)(-)

    Voltage

    (Approx.)
    Front combination lamp LH
    ConnectorTerminal
    E249 3 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

GO TO 7.

CHECK HEADLAMP LH CONTROL SIGNAL CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect IPDM E/R connector.

  3. Check continuity between front combination lamp LH harness connector and IPDM E/R harness connector.

    Front combination lamp LHIPDM E/RContinuity
    ConnectorTerminalConnectorTerminal
    E249 3 E217 50 Yes

Is the inspection result normal?

YES>>

Replace IPDM E/R. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK HEADLAMP LH LIN COMMUNICATION CIRCUIT 2

  1. Ignition switch OFF.

  2. Disconnect IPDM E/R connector.

  3. Check continuity between front combination lamp LH harness connector and IPDM E/R harness connector.

    Front combination lamp LHIPDM E/RContinuity
    ConnectorTerminalConnectorTerminal
    E249 2 E119 38 Yes

Is the inspection result normal?

YES>>

Replace front combination lamp LH. Refer to Removal and Installation.

NO>>

Repair or replace harness.

B20d4-11 Tail Lamp Lh Pwr Sply Circ Nissan Pathfinder 2026

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC detection condition
B20D4–11

TAIL LAMP LH PWR SPLY CIRC

(Tail lamp left hand power supply circuit)
[CIRCUIT SHORT TO GROUND] Diagnosis condition When the license plate lamp, side marker lamp and tail lamp ON conditions are satisfied (Smart FET inside IPDM E/R is ON)
Signal (terminal)

The following power supply circuit:

  • Side marker lamp

  • Tail lamp

  • License plate lamp

Threshold Overcurrent is detected
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Harness or connector

  • Front combination lamp LH

  • Front combination lamp RH

  • Rear combination lamp (body side) LH

    • LED (tail lamp)

    • Harness

  • Rear combination lamp (body side) RH

    • LED (tail lamp)

    • Harness

  • Rear combination lamp (back door side) LH

    • LED (tail lamp)

  • Rear combination lamp (back door side) RH

    • LED (tail lamp)

  • Rear side marker lamp LH bulb

  • Rear side marker lamp LH bulb socket or harness

  • Rear side marker lamp RH bulb

  • Rear side marker lamp RH bulb socket or harness

  • License plate lamp LH

  • License plate lamp RH

  • IPDM E/R

FAIL-SAFE

Shuts off the power supply to the following power supply circuits until the license plate lamp, side marker lamp and tail lamp ON conditions are no longer satisfied:

  • Tail lamp LH

  • Tail lamp RH

  • License plate lamp LH

  • License plate lamp RH

  • Front side marker lamp LH

  • Front side marker lamp RH

  • Rear side marker lamp LH

  • Rear side marker lamp RH

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

CONSULT

  1. Ignition switch ON.

  2. Select “T LAMP LH CIRC MALFUNCTN” and “T LAMP RH CIRC MALFUNCTN” in “Data Monitor” mode of “IPDM E/R”.

  3. Check the monitor status.

    Monitor itemMonitor status
    T LAMP LH CIRC MALFUNCTN 0
    1
    T LAMP RH CIRC MALFUNCTN 0
    1

What is the monitor status?

“0”>>

GO TO 2.

“1”>>

A short circuit is detected multiple times in the side marker lamp, tail lamp or license plate lamp power supply circuit, and damage accumulates at the Smart FET inside the IPDM E/R. For this reason, IPDM E/R does not turn ON the Smart FET. Because the DTC cannot be reproduced in this state, perform DTC Diagnosis Procedure and replace IPDM E/R after the malfunctioning part is repaired. Refer to Removal and Installation.

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch OFF.

  2. Ignition switch ON.

  3. Turn lighting switch 1ST.

  4. Select “Self Diagnostic Result” mode of “IPDM E/R”.

  5. Check DTC.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK TAIL LAMP POWER SUPPLY CIRCUIT (SHORT)

  1. Ignition switch OFF.

  2. Disconnect the following connectors:

    • IPDM E/R

    • Front combination lamp LH

    • Front combination lamp RH

    • Rear combination lamp LH (body side)

    • Rear combination lamp RH (body side)

    • Rear combination lamp LH (back door side)

    • Rear combination lamp RH (back door side)

    • License plate lamp LH

    • License plate lamp RH

  3. Check continuity between IPDM E/R harness connector and ground.

    IPDM E/R(-)Continuity
    ConnectorTerminal
    E120 4 Ground No
    17

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace harness.

CHECK TAIL LAMP POWER SUPPLY

  1. Connect IPDM E/R connector.

  2. Ignition switch ON.

  3. With operating the lighting switch, check voltage between rear combination lamp (body side) harness connector and ground.

    (+)(-)Condition

    Voltage

    (Approx.)
    Rear combination lamp (body side)
    ConnectorTerminal
    RH B413 2 Ground Lighting switch 1ST Battery voltage
    OFF or AUTO* 0 V
    LH B412 1ST Battery voltage
    OFF or AUTO* 0 V

    *: Only when the illumination judgement by intelligent auto light system is OFF.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Replace IPDM E/R. Refer to Removal and Installation.

CHECK TAIL LAMP

Check the tail lamp. Refer to Component Inspection (Tail Lamp).

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace the malfunctioning part.

CHECK LICENSE PLATE LAMP

Check the license plate lamp. Refer to Component Inspection (License Plate Lamp).

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace the malfunctioning part.

CHECK FRONT SIDE MARKER LAMP

Check the front side marker lamp. Refer to Component Inspection (Front Side Marker Lamp).

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace the malfunctioning part.

CHECK REAR SIDE MARKER LAMP

Check the rear side marker lamp. Refer to Component Inspection (Rear Side Marker Lamp).

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Repair or replace the malfunctioning part.

Component Inspection (Tail Lamp)

CHECK TAIL LAMP

  1. Ignition switch OFF.

  2. Disconnect rear combination lamp connector.

  3. Check continuity between rear combination lamp terminals.

    Body side
    Rear combination lamp (body side)Continuity
    Terminal
    +–
    2 1 Yes
    Back door side
    Rear combination lamp (back door side)Continuity
    Terminal
    +–
    2 1 Yes

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Body side: Replace corresponding rear combination lamp (body side). Refer to Removal and Installation.

NO>>

Back door side: Replace corresponding rear combination lamp (back door side). Refer to Removal and Installation.

Component Inspection (License Plate Lamp)

CHECK LICENSE PLATE LAMP

  1. Ignition switch OFF.

  2. Disconnect license plate lamp connector.

  3. Check continuity between license plate lamp terminals.

    License plate lampContinuity
    Terminal
    +–
    2 1 Yes

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace corresponding license plate lamp. Refer to Removal and Installation.

Component Inspection (Front Side Marker Lamp)

CHECK FRONT SIDE MARKER LAMP

  1. Ignition switch OFF.

  2. Disconnect front combination lamp connector.

  3. Check continuity between front combination lamp terminals.

    Front combination lampContinuity
    Terminal
    +–
    10 9 Yes

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace corresponding front combination lamp. Refer to Removal and Installation.

Component Inspection (Rear Side Marker Lamp)

CHECK REAR SIDE MARKER LAMP

  1. Ignition switch OFF.

  2. Disconnect rear combination lamp (body side) connector.

  3. Check continuity between rear combination lamp (body side) terminals.

    Rear combination lamp (body side)Continuity
    Terminal
    +–
    2 1 Yes

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace corresponding rear side marker lamp bulb. Refer to Bulb Replacement.

B20e3-96 Led Headlamp Lh Nissan Pathfinder 2022

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC detection condition
B20E3–96

LED HEADLAMP LH

(Light emitting diode headlamp left hand)
[CMPNENT INTERNAL MLFNCTN] Diagnosis condition Ignition switch ON
Signal (terminal) Headlamp warning signal (via LIN communication)
Threshold Detected a malfunction of headlamp LH (LO) circuit
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

  • Front combination lamp LH

    • LED [Headlamp (LO)]

    • LED headlamp control module

FAIL-SAFE

  • Transmits the headlamp warning signal to the combination meter via CAN communication (when the ignition switch is placed ON, the headlamp warning is displayed on the information display of the combination meter).

  • Transmits the request signal to both side LED headlamp control modules via LIN communication, and turns ON the headlamp (LO) and parking lamp.

DTC CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Select “Self Diagnostic Result” mode of “IPDM E/R”.

  3. Check DTC.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

REPLACE HEADLAMP LH

Replace the front combination lamp LH. Refer to Removal and Installation.

>>

Inspection End.

Front Side Marker Lamp Circuit Nissan Pathfinder Fifth generation

Component Function Check

CHECK TAIL LAMP OPERATION

Check tail lamp is turned ON when lighting switch is turned 1ST.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Check tail lamp circuit. Refer to Component Function Check.

CHECK FRONT SIDE MARKER LAMP OPERATION

  1. Ignition switch ON.

  2. With operating the lighting switch, check that the front side marker lamp is turned ON.

    Lighting switch 1ST : Front side marker lamp ON
    Lighting switch OFF or AUTO* : Front side marker lamp OFF

    *: Only when the illumination judgement by intelligent auto light system is OFF.

Is the inspection result normal?

YES>>

Front side marker lamp circuit is normal.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK FRONT SIDE MARKER LAMP POWER SUPPLY CIRCUIT

  1. Disconnect IPDM E/R connector and front combination lamp connector.

  2. Check continuity between IPDM E/R harness connector and front combination lamp harness connector.

    IPDM E/RFront combination lampContinuity
    ConnectorTerminalConnectorTerminal
    RH E120 17 E241 10 Yes
    LH 4 E239

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace harness.

CHECK FRONT SIDE MARKER LAMP GROUND CIRCUIT

Check continuity between front combination lamp harness connector and ground.

Front combination lamp—Continuity
ConnectorTerminal
RH E241 9 Ground Yes
LH E239

Is the inspection result normal?

YES>>

Replace corresponding front combination lamp. Refer to Removal and Installation.

NO>>

Repair or replace harness.

Tail Lamp Circuit Nissan Pathfinder 5th Gen

Component Function Check

CHECK TAIL LAMP OPERATION

  1. Ignition switch ON.

  2. With operating the lighting switch, check that the tail lamp is turned ON.

    Lighting switch 1ST : Tail Lamp ON
    Lighting switch OFF or AUTO* : Tail lamp OFF

    *: Only when the illumination judgement by intelligent auto light system is OFF.

Is the inspection result normal?

YES>>

Tail lamp circuit is normal.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK TAIL LAMP OUTPUT VOLTAGE

  1. Ignition switch ON.

  2. With operating the lighting switch, check voltage between IPDM E/R harness connector and ground.

    +-Condition

    Voltage

    (Approx.)
    IPDM E/R
    ConnectorTerminal
    RH E120 17 Ground Lighting switch 1ST Battery voltage
    OFF or AUTO* 0 V
    LH 4 1ST Battery voltage
    OFF or AUTO* 0 V

    *: Only when the illumination judgement by intelligent auto light system is OFF.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 2.

CHECK TAIL LAMP OUTPUT CIRCUIT (SHORT)

  1. Disconnect the following connectors:

    • Front combination lamp LH

    • Front combination lamp RH

    • Rear combination lamp LH (body side)

    • Rear combination lamp RH (body side)

    • Rear combination lamp LH (back door side)

    • Rear combination lamp RH (back door side)

    • License plate lamp LH

    • License plate lamp RH

    • IPDM E/R

  2. Check continuity between IPDM E/R harness connector and ground.

IPDM E/R—Continuity
ConnectorTerminal
RH E120 17 Ground No
LH 4

Is the inspection result normal?

YES>>

Replace IPDM E/R. Refer to Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK TAIL LAMP POWER SUPPLY CIRCUIT

  1. Ignition switch OFF.

  2. Turn lighting switch OFF or AUTO.

  3. Disconnect IPDM E/R connector and rear combination lamp connector.

  4. Check continuity between IPDM E/R harness connector and rear combination lamp harness connector.

    Body side
    IPDM E/RRear combination lamp (body side)Continuity
    ConnectorTerminalConnectorTerminal
    RH E120 17 B413 2 Yes
    LH 4 B412
    Back door side
    IPDM E/RRear combination lamp (back door side)Continuity
    ConnectorTerminalConnectorTerminal
    RH E120 17 D562 2 Yes
    LH 4 D511

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace harness.

CHECK TAIL LAMP GROUND CIRCUIT

Check continuity between rear combination lamp harness connector and ground.

Body side
Rear combination lamp (body side)—Continuity
ConnectorTerminal
RH B413 1 Ground Yes
LH B412
Back door side
Rear combination lamp (back door side)—Continuity
ConnectorTerminalTerminal
RH D562 1 Ground Yes
LH D511

Is the inspection result normal?

YES>>

Body side: Replace corresponding rear combination lamp (body side). Refer to Removal and Installation.

YES>>

Back door side: Replace corresponding rear combination lamp (back door side). Refer to Removal and Installation.

NO>>

Repair or replace harness.

License Plate Lamp Circuit Nissan Pathfinder R53

Component Function Check

CHECK TAIL LAMP LH OPERATION

Check that tail lamp LH is turned ON when lighting switch is turned 1ST.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Check tail lamp circuit. Refer to Component Function Check.

CHECK LICENSE PLATE LAMP OPERATION

  1. Ignition switch ON.

  2. With operating the lighting switch, check that the license plate lamp is turned ON.

    Lighting switch 1ST : License plate lamp ON
    Lighting switch OFF or AUTO* : License plate lamp OFF

    *: Only when the illumination judgement by intelligent auto light system is OFF.

Is the inspection result normal?

YES>>

License plate lamp circuit is normal.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK LICENSE PLATE LAMP POWER SUPPLY CIRCUIT

  1. Disconnect IPDM E/R connector and license plate lamp connector.

  2. Check continuity between IPDM E/R harness connector and license plate lamp harness connector.

    IPDM E/RLicense plate lampContinuity
    ConnectorTerminalConnectorTerminal
    RH E120 4 B461 2 Yes
    LH B460

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace harness.

CHECK LICENSE PLATE LAMP GROUND CIRCUIT

Check continuity between license plate lamp harness connector and ground.

License plate lamp—Continuity
ConnectorTerminal
RH B461 1 Ground Yes
LH B460

Is the inspection result normal?

YES>>

Replace corresponding license plate lamp. Refer to Removal and Installation.

NO>>

Repair or replace harness.

Rear Side Marker Lamp Circuit Nissan Pathfinder 5th Gen

Component Function Check

CHECK TAIL LAMP OPERATION

Check that tail lamp is turned ON when lighting switch is turned 1ST.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Check tail lamp circuit. Refer to Component Function Check.

CHECK REAR SIDE MARKER LAMP OPERATION

  1. Ignition switch ON.

  2. With operating the lighting switch, check that the rear side marker lamp is turned ON.

    Lighting switch 1ST : Rear side marker lamp ON
    Lighting switch OFF or AUTO* : Rear side marker lamp OFF

    *: Only when the illumination judgement by intelligent auto light system is OFF.

Is the inspection result normal?

YES>>

Rear side marker lamp circuit is normal.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK REAR SIDE MARKER LAMP BULB

  1. Ignition switch OFF.

  2. Check the rear side marker lamp bulb.

Is the inspection result normal?

YES>>

Check corresponding rear side marker lamp bulb socket. Repair or replace if necessary.

NO>>

Replace corresponding rear side marker lamp bulb. Refer to Bulb Replacement.

Stop Lamp Circuit Nissan Pathfinder R53

Component Function Check

CHECK STOP LAMP OPERATION

  1. Ignition switch ON.

  2. With operating the brake pedal, check that the stop lamp and high-mounted stop lamp is turned ON.

    Depressed : Stop lamp and high-mounted stop lamp ON
    Fully released : Stop lamp and high-mounted stop lamp OFF

Is the inspection result normal?

YES>>

Stop lamp circuit is normal.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK SYMPTOM

Check symptom (A or B)

Symptom
A All of stop lamp and high-mounted stop lamp are not turned ON
B Any of stop lamp and high-mounted stop lamp are not turned ON

Which symptom is detected?

A>>

GO TO 2.

B>>

GO TO 10.

CHECK FUSE

  1. Ignition switch OFF.

  2. Check that any of the following fuse is not blown (open):

    UnitLocationFuse No.Capacity
    • Battery power supply (stop lamp)

    • Battery power supply (stop lamp switch)

    Fuse block (J/B) 21 10 A

Is the fuse blown (open)?

YES>>

Replace the blown (open) fuse after repairing the affected circuit if a fuse is blown (open).

NO>>

GO TO 3.

CHECK BATTERY POWER SUPPLY (STOP LAMP)

  1. Disconnect BCM connector.

  2. Check voltage between BCM harness connector and ground.
    +-

    Voltage

    (Approx.)
    BCM
    ConnectorTerminal
    M81 139 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

GO TO 4.

CHECK BATTERY POWER SUPPLY CIRCUIT (STOP LAMP)

  1. Disconnect fuse block (J/B) connector

  2. Check voltage between BCM harness connector and fuse block (J/B) harness connector.

    BCM Fuse block (J/B) Continuity
    Connector Terminal Connector Terminal
    M81 139 E28 2R Yes

Is the inspection result normal?

YES>>

Replace fuse block (J/B).

NO>>

Repair or replace harness.

CHECK STOP LAMP SWITCH POWER SUPPLY

  1. Disconnect stop lamp switch connector.

  2. Check voltage between stop lamp switch harness connector and ground.

    +-

    Voltage

    (Approx.)
    Stop lamp switch
    ConnectorTerminal
    E38 1 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

GO TO 6.

CHECK STOP LAMP SWITCH POWER SUPPLY CIRCUIT

  1. Disconnect fuse block (J/B) connector.

  2. Check continuity between stop lamp switch harness connector and fuse block (J/B) harness connector.

    Stop lamp switch Fuse block (J/B) Continuity
    Connector Terminal Connector Terminal
    E38 1 E28 2R Yes

Is the inspection result normal?

YES>>

Replace fuse block (J/B).

NO>>

Repair or replace harness.

CHECK STOP LAMP SWITCH SIGNAL

  1. Connect stop lamp switch connector.

  2. With operating the brake pedal, check voltage between BCM harness connector and ground.

    +-Condition

    Voltage

    (Approx.)
    BCM
    ConnectorTerminal
    M80 110 Ground Ignition switch ON Brake pedal is released 0 V
    OFF
    ON Brake pedal is depressed Battery voltage
    OFF

Is the inspection result normal?

YES>>

Replace BCM. Refer to Removal and Installation.

NO>>

GO TO 8.

CHECK STOP LAMP SWITCH

Check stop lamp switch. Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Replace stop lamp switch. Refer to Exploded View.

CHECK STOP LAMP SWITCH SIGNAL CIRCUIT (OPEN)

  1. Disconnect stop lamp switch connector.

  2. Check continuity between BCM harness connector and stop lamp switch harness connector.

    BCM Stop lamp switch Continuity
    Connector Terminal Connector Terminal
    M80 110 E38 2 Yes

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Repair or replace harness.

CHECK STOP LAMP / HIGH-MOUNTED STOP LAMP OUTPUT VOLTAGE

CONSULT

  1. Ignition switch ON.

  2. Select “STOP LAMP 1” or “STOP LAMP 2” in “Active Test” mode of "BCM(HEAD LAMP)".

  3. With operating the test items, check voltage between BCM harness connector and ground.

    Stop lamp RH
    +-Test item

    Voltage

    (Approx.)
    BCM
    ConnectorTerminal
    B45 157 Ground STOP LAMP 1 On Battery voltage
    Off 0 V
    Stop lamp LH and high-mounted stop lamp
    +-Test item

    Voltage

    (Approx.)
    BCM
    ConnectorTerminal
    B45 160 Ground STOP LAMP 2 On Battery voltage
    Off 0 V

Is the inspection result normal?

YES>>

GO TO 12.

NO>>

GO TO 11.

CHECK STOP LAMP / HIGH-MOUNTED STOP LAMP POWER SUPPLY CIRCUIT (SHORT)

  1. Ignition switch OFF.

  2. Disconnect the following connectors:

    • BCM

    • Rear combination lamp LH (body side)

    • Rear combination lamp RH (body side)

    • High-mounted stop lamp

  3. Check continuity between BCM harness connector and ground.

    BCM—Continuity
    ConnectorTerminal
    B45 160 Ground No
    157

Is the inspection result normal?

YES>>

Replace BCM. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK STOP LAMP / HIGH-MOUNTED STOP LAMP POWER SUPPLY CIRCUIT (OPEN)

  1. Ignition switch OFF.

  2. Disconnect the following connectors:

    • BCM

    • Rear combination lamp LH (body side)

    • Rear combination lamp RH (body side)

    • High-mounted stop lamp

  3. Check continuity between BCM harness connector, rear combination lamp LH (body side) harness connector, rear combination lamp RH (body side) harness connector and high-mounted stop lamp harness connector.

    Stop lamp
    BCMRear combination lamp (body side)Continuity
    ConnectorTerminalConnectorTerminal
    RH B45 157 B413 4 Yes
    LH 160 B412
    High-mounted stop lamp
    BCMHigh-mounted stop lampContinuity
    ConnectorTerminalConnectorTerminal
    B45 160 D517 2 Yes

Is the inspection result normal?

YES>>

GO TO 13.

NO>>

Repair or replace harness.

CHECK STOP LAMP / HIGH-MOUNTED STOP LAMP GROUND CIRCUIT

Check continuity between rear combination lamp LH (body side) harness connector, rear combination lamp RH (body side) harness connector, high-mounted stop lamp harness connector and ground.

Stop lamp
Rear combination lamp (body side)—Continuity
ConnectorTerminal
RH B413 1 Ground Yes
LH B412
High-mounted stop lamp
High-mounted stop lamp—Continuity
ConnectorTerminal
D517 1 Ground Yes

Is the inspection result normal?

YES>>

Stop lamp: Replace corresponding rear combination lamp (body side). Refer to Removal and Installation.

YES>>

High-mounted stop lamp: Replace high-mounted stop lamp. Refer to Removal and Installation.

NO>>

Repair or replace harness.

Component Inspection

CHECK STOP LAMP SWITCH-1

  1. Ignition switch OFF.

  2. Disconnect stop lamp switch connector.

  3. Check continuity between stop lamp switch terminals.

    Stop lamp switchConditionContinuity
    Terminal
    +–
    1 2 Brake pedal Depressed Yes
    Fully released No

Is the inspection result normal?

YES>>

Inspection End.

NO>>

GO TO 2.

CHECK STOP LAMP SWITCH-2

  1. Adjust stop lamp switch installation. Refer to Inspection.

  2. Check continuity between stop lamp switch terminals.

    Stop lamp switchConditionContinuity
    Terminal
    +–
    1 2 Brake pedal Depressed Yes
    Fully released No

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace stop lamp switch. Refer to Exploded View.

Back-Up Lamp Circuit Nissan Pathfinder Fifth generation

Component Function Check

CHECK BACK-UP LAMP OPERATION

  1. Start the engine.

  2. With operating the shift selector, check that the back-up lamp is turned ON.

    Shift selector position: R range : Back-up lamp ON
    Shift selector position: Other than above : Back-up lamp OFF

Is the inspection result normal?

YES>>

Back-up lamp circuit is normal.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK BACK-UP LAMP BULB

  1. Ignition switch OFF.

  2. Check the back-up lamp bulb.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace corresponding back-up lamp bulb. Refer to Bulb Specifications.

CHECK BACK-UP LAMP RELAY FUSE

Check that the following fuse is not blown (open):

UnitLocationFuse No.Capacity
Back-up lamp relay IPDM E/R 71 10 A

Is the fuse blown (open)?

YES>>

Replace the blown (open) fuse after repairing the affected circuit if a fuse is blown (open).

NO>>

GO TO 3.

CHECK BACK-UP LAMP RELAY POWER SUPPLY

  1. Ignition switch ON.

  2. Check voltage between IPDM E/R harness connector and ground.

    (+)(-)

    Voltage

    (Approx.)
    IPDM E/R
    ConnectorTerminal
    F24 71 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Replace IPDM E/R. Refer to Removal and Installation.

CHECK BACK-UP LAMP RELAY POWER SUPPLY CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect IPDM E/R connector and back-up lamp relay connector.

  3. Check continuity between IPDM E/R harness connector and back-up lamp relay harness connector.

    Without heated steering wheel
    IPDM E/R Back-up lamp relay Continuity
    Connector Terminal Connector Terminal
    F24 71 M93 1 Yes
    3
    With heated steering wheel
    IPDM E/R Heated steering wheel relay and back-up lamp relay Continuity
    Connector Terminal Connector Terminal
    F24 71 M90 6 Yes
    8

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace harness.

CHECK BACK-UP LAMP RELAY

Check back-up lamp relay. Refer to Component Inspection (Without Heated Steering Wheel) or Component Inspection (With Heated Steering Wheel).

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Replace back-up lamp relay.

CHECK BACK-UP LAMP RELAY CONTROL SIGNAL

  1. Connect IPDM E/R connector and back-up lamp relay connector.

  2. Start the engine.

  3. With operating the shift selector, check voltage between BCM harness connector and ground.

    (+)(-)Condition

    Voltage

    (Approx.)
    BCM
    ConnectorTerminal
    M80 119 Ground Shift selector position R range 0 V
    Except R range Battery voltage

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Fixed at 0 V: GO TO 7.

NO>>

Fixed at battery voltage: Replace BCM. Refer to Removal and Installation.

CHECK BACK-UP LAMP RELAY CONTROL SIGNAL CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect BCM connector and back-up lamp relay connector.

  3. Check continuity between BCM harness connector and back-up lamp relay harness connector.

    Without heated steering wheel
    BCM Back-up lamp relay Continuity
    Connector Terminal Connector Terminal
    M80 119 M93 4 Yes
    With heated steering wheel
    BCM Heated steering wheel relay and back-up lamp relay Continuity
    Connector Terminal Connector Terminal
    M80 119 M90 9 Yes
  4. Check continuity between BCM connector and ground.

    BCM(-)Continuity
    ConnectorTerminal
    M80 119 Ground No

Is the inspection result normal?

YES>>

Replace BCM. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK BACK-UP LAMP POWER SUPPLY CIRCUIT 1

  1. Ignition switch OFF.

  2. Disconnect back-up lamp relay connector and rear combination lamp (back door side) connector.

  3. Check continuity between back-up lamp relay harness connector and rear combination lamp (back door side) harness connector.

    Without heated steering wheel
    Back-up lamp relayRear combination lamp (back door side)Continuity
    ConnectorTerminalConnectorTerminal
    RH M93 2 D564 2 Yes
    LH D506
    With heated steering wheel
    Heated steering wheel relay and back-up lamp relayRear combination lamp (back door side)Continuity
    ConnectorTerminalConnectorTerminal
    RH M90 7 D564 2 Yes
    LH D506

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Repair or replace harness.

CHECK BACK-UP LAMP GROUND CIRCUIT

Check continuity between rear combination lamp (back door side) harness connector and ground.

Rear combination lamp (back door side)(-)Continuity
ConnectorTerminal
RH D564 1 Ground Yes
LH D506

Is the inspection result normal?

YES>>

Check corresponding back-up lamp bulb socket. Repair or replace if necessary.

NO>>

Repair or replace harness.

Component Inspection (Without Heated Steering Wheel)

CHECK BACK-UP LAMP RELAY

  1. Ignition switch OFF.

  2. Disconnect back-up lamp relay connector.

  3. Apply battery voltage to back-up lamp relay between terminals 3 and 4.

  4. Check continuity between back-up lamp relay terminals.

    Back-up lamp relayConditionContinuity
    Terminal
    +–
    1 2 Battery voltage Applied Yes
    Not applied No

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace back-up lamp relay.

Component Inspection (With Heated Steering Wheel)

CHECK BACK-UP LAMP RELAY

  1. Ignition switch OFF.

  2. Disconnect back-up lamp relay connector.

  3. Apply battery voltage to back-up lamp relay between terminals 8 and 9.

  4. Check continuity between back-up lamp relay terminals.

    Heated steering wheel relay and back-up lamp relayConditionContinuity
    Terminal
    +–
    6 7 Battery voltage Applied Yes
    Not applied No

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace back-up lamp relay.

Front Fog Lamp Circuit Nissan Pathfinder R53

Component Function Check

CHECK FRONT FOG LAMP OPERATION

  1. Ignition switch ON.

  2. Turn lighting switch 2ND.

  3. With operating the front fog lamp switch, check that the front fog lamp is turned ON.

    Front fog lamp switch ON : Front fog lamp ON
    Front fog lamp switch OFF : Front fog lamp OFF

Is the inspection result normal?

YES>>

Front fog lamp circuit is normal.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK FRONT FOG LAMP OUTPUT VOLTAGE

  1. Ignition switch ON.

  2. Turn lighting switch 2ND.

  3. With operating the front fog lamp switch, check voltage between IPDM E/R harness connector and ground.

    +-Condition

    Voltage

    (Approx.)
    IPDM E/R
    ConnectorTerminal
    RH E218 57 Ground Front fog lamp switch ON Battery voltage
    OFF 0 V
    LH E217 51 ON Battery voltage
    OFF 0 V

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 2.

CHECK FRONT FOG LAMP OUTPUT CIRCUIT (SHORT)

  1. Disconnect IPDM E/R connector, front fog lamp LH connector and front fog lamp RH connector

  2. Check continuity between IPDM E/R harness connector and ground.

IPDM E/R—Continuity
ConnectorTerminal
RH E218 57 Ground No
LH E217 51

Is the inspection result normal?

YES>>

Replace IPDM E/R. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK FRONT FOG LAMP POWER SUPPLY CIRCUIT

  1. Ignition switch OFF.

  2. Turn lighting switch OFF or AUTO.

  3. Disconnect IPDM E/R connector and front fog lamp connector.

  4. Check continuity between IPDM E/R harness connector and front fog lamp harness connector.

    IPDM E/RFront fog lampContinuity
    ConnectorTerminalConnectorTerminal
    RH E218 57 E306 2 Yes
    LH E217 51 E305

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace harness.

CHECK FRONT FOG LAMP GROUND CIRCUIT

Check continuity between front fog lamp harness connector and ground.

Front fog lamp—Continuity
ConnectorTerminal
RH E306 1 Ground Yes
LH E305

Is the inspection result normal?

YES>>

Replace corresponding front fog lamp. Refer to Removal and Installation.

NO>>

Repair or replace harness.

Turn Signal Lamp Circuit Nissan Pathfinder Fifth generation

Component Function Check

CHECK TURN SIGNAL LAMP OPERATION

CONSULT

  1. Ignition switch ON.

  2. Select “FLASHER” in “Active Test” mode of "BCM(FLASHER)".

  3. With operating the test items, check that the turn signal lamp blinks.

    RH : Turn signal lamps RH blink
    LH : Turn signal lamps LH blink
    LH/RH : Turn signal lamps RH and LH blinks

Is the inspection result normal?

YES>>

Turn signal lamp circuit is normal.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK SYMPTOM

Check symptom (A or B)

Symptom
A All turn signal lamps do not blink
B Applicable side performs high flasher activation

Which symptom is detected?

A>>

GO TO 2.

B>>

GO TO 4.

CHECK FUSE

  1. Ignition switch OFF.

  2. Check that the following fuse is not blown (open):

    UnitLocationFuse No.Capacity
    BCM Fuse block (J/B) 53 10 A

Is the fuse blown (open)?

YES>>

Replace the blown (open) fuse after repairing the affected circuit if a fuse is blown (open).

NO>>

GO TO 3.

CHECK BCM POWER SUPPLY (TURN SIGNAL LAMP)

  1. Disconnect BCM connector.

  2. Check voltage between BCM harness connector and ground.

    +-

    Voltage

    (Approx)
    BCM
    ConnectorTerminal
    M81 136 Ground Battery voltage

Is the inspection result normal?

YES>>

Replace BCM. Refer to Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK TURN SIGNAL LAMP BULB

  1. Ignition switch OFF.

  2. Check each turn signal lamp bulb.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Front turn signal lamp: Replace corresponding front turn signal lamp bulb. Refer to Bulb Replacement.

NO>>

Rear turn signal lamp: Replace corresponding rear turn signal lamp bulb. Refer to Bulb Replacement.

CHECK TURN SIGNAL LAMP OUTPUT VOLTAGE

  1. Ignition switch ON.

  2. With operating the turn signal switch, check voltage between BCM harness connector and ground.

    Front turn signal lamp
    +-Condition

    Voltage

    (Approx.)
    BCM
    ConnectorTerminal
    RH M80 116 Ground Turn signal switch Right Blinking : 0 V <–> Battery voltage
    Center 0 V
    LH 128 Left Blinking : 0 V <–> Battery voltage
    Center 0 V
    Side turn signal lamp
    +-Condition

    Voltage

    (Approx.)
    BCM
    ConnectorTerminal
    RH M18 1 Ground Turn signal switch Right Blinking : 0 V <–> Battery voltage
    Center 0 V
    LH 21 Left Blinking : 0 V <–> Battery voltage
    Center 0 V
    Rear turn signal lamp
    +-Condition

    Voltage

    (Approx.)
    BCM
    ConnectorTerminal
    RH B45 159 Ground Turn signal switch Right Blinking : 0 V <–> Battery voltage
    Center 0 V
    LH 151 Left Blinking : 0 V <–> Battery voltage
    Center 0 V

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

GO TO 6.

CHECK TURN SIGNAL LAMP POWER SUPPLY CIRCUIT (SHORT)

  1. Ignition switch OFF.

  2. Disconnect BCM connector.

  3. Check continuity between BCM harness connector and ground.

    Front turn signal lamp
    BCM—Continuity
    ConnectorTerminal
    RH M80 116 Ground No
    LH 128
    Side turn signal lamp
    BCM—Continuity
    ConnectorTerminal
    RH M18 1 Ground No
    LH 21
    Rear turn signal lamp
    BCM—Continuity
    ConnectorTerminal
    RH B45 159 Ground No
    LH 151

Is the inspection result normal?

YES>>

Replace BCM. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK TURN SIGNAL LAMP POWER SUPPLY CIRCUIT (OPEN)

  1. Ignition switch OFF.

  2. Disconnect the following connectors:

    • Front combination lamp LH

    • Front combination lamp RH

    • Rear combination lamp LH (body side) connector

    • Rear combination lamp RH (body side) connector

    • Door mirror LH

    • Door mirror RH

    • BCM

  3. Check continuity between BCM harness connector, front combination lamp LH harness connector, front combination lamp RH harness connector, rear combination lamp LH (body side) harness connector, rear combination lamp RH (body side) harness connector, door mirror LH harness connector and door mirror RH harness connector.

    Front turn signal lamp
    BCMFront combination lampContinuity
    ConnectorTerminalConnectorTerminal
    RH M80 116 E250 7 Yes
    LH 128 E249
    Side turn signal lamp
    BCMDoor mirrorContinuity
    ConnectorTerminalConnectorTerminal
    RH M18 1 D128 5 Yes
    LH 21 D28
    Rear turn signal lamp
    BCMRear combination lamp (body side)Continuity
    ConnectorTerminalConnectorTerminal
    RH B45 159 B413 3 Yes
    LH 151 B412

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair or replace harness.

CHECK TURN SIGNAL LAMP GROUND CIRCUIT

Check continuity between front combination lamp LH harness connector, front combination lamp RH harness connector, rear combination lamp LH (body side) harness connector, rear combination lamp RH (body side) harness connector, door mirror LH harness connector, door mirror RH harness connector and ground.

Front turn signal lamp
Front combination lamp—Continuity
ConnectorTerminal
RH E250 8 Ground Yes
LH E249
Side turn signal lamp
Door mirror—Continuity
ConnectorTerminal
RH D128 4 Ground Yes
LH D28
Rear turn signal lamp
Rear combination lamp (body side)—Continuity
ConnectorTerminal
RH B413 1 Ground Yes
LH B412

Is the inspection result normal?

YES>>

Front turn signal lamp bulb: Replace corresponding front turn signal lamp bulb. Refer to Bulb Replacement.

YES>>

Side turn signal lamp: Replace corresponding door mirror. Refer to Removal and Installation.

YES>>

Rear turn signal lamp: Replace corresponding rear turn signal lamp bulb. Refer to Bulb Replacement.

NO>>

Repair or replace harness.

Hazard Switch Circuit Nissan Pathfinder Fifth generation

Component Function Check

CHECK HAZARD SWITCH SIGNAL

CONSULT

  1. Ignition switch ON.

  2. Select “HAZARD SW” in “Data Monitor” mode of "BCM(FLASHER)".

  3. With operating the hazard switch, check the monitor status.

    Monitor itemConditionMonitor status
    HAZARD SW Hazard switch ON On
    OFF Off

Is the inspection result normal?

YES>>

Hazard switch circuit is normal.

NO>>

Refer to Diagnosis Procedure.

Diagnosis Procedure

CHECK HAZARD SWITCH SIGNAL

  1. Ignition switch OFF.

  2. Disconnect hazard switch connector.

  3. Check voltage between hazard switch harness connector and ground.

    +-

    Voltage

    (Approx.)
    Hazard switch
    ConnectorTerminal
    M26 2 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 2.

CHECK HAZARD SWITCH SIGNAL CIRCUIT (OPEN)

  1. Disconnect BCM connector.

  2. Check continuity between hazard switch harness connector and BCM harness connector.

    Hazard switchBCMContinuity
    ConnectorTerminalConnectorTerminal
    M26 2 M18 13 Yes

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace harness.

CHECK HAZARD SWITCH SIGNAL CIRCUIT (SHORT)

Check continuity between hazard switch harness connector and ground.

Hazard switch—Continuity
ConnectorTerminal
M26 2 Ground No

Is the inspection result normal?

YES>>

Replace BCM. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK HAZARD SWITCH GROUND CIRCUIT

Check continuity between hazard switch harness connector and ground.

Hazard switch—Continuity
ConnectorTerminal
M26 3 Ground Yes

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace harness.

CHECK HAZARD SWITCH

Check hazard switch. Refer to Component Inspection.

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace hazard switch. Refer to Removal and Installation.

Component Inspection

CHECK HAZARD SWITCH

  1. Ignition switch OFF.

  2. Disconnect hazard switch connector.

  3. Check continuity between hazard switch terminals.

    Hazard switchConditionContinuity
    Terminal
    +–
    2 3 Hazard switch ON Yes
    OFF No

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace hazard switch. Refer to Removal and Installation.