Steering Control System - Symptom Diagnosis
- Power Steering Warning Lamp Does Not Turn on
- Power Steering Warning Lamp Does Not Turn Off
- Steering Wheel Turning Force Is Heavy or Light
- Unbalance Steering Wheel Turning Force and Return Between Right and Left
Power Steering Warning Lamp Does Not Turn on Nissan Pathfinder 2026
Description
The power steering warning lamp does not illuminate when the ignition switch is placed ON (lamp check).
Diagnosis Procedure
CHECK THE POWER STEERING WARNING LAMP
Perform trouble diagnosis for the power steering warning lamp system. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>Check that the pin terminals and the connection of each connector are normal.
NO>>Repair or replace malfunctioning components.
Power Steering Warning Lamp Does Not Turn Off Nissan Pathfinder 5th Gen
Description
Power steering warning lamp does not turn OFF several seconds after engine started.
Diagnosis Procedure
PERFORM SELF-DIAGNOSIS
CONSULT
Select “Self Diagnostic Result” mode of “EPS/DAST 3”.
Is any DTC detected?
YES>>Check the DTC. Refer to DTC Index.
NO>>GO TO 2.
CHECK POWER STEERING WARNING LAMP
Perform the trouble diagnosis of power steering warning lamp. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair or replace malfunctioning components.
EPS CONTROL UNIT POWER SUPPLY AND GROUND CIRCUIT
Perform the trouble diagnosis of EPS control unit power supply and ground. Refer to Diagnosis Procedure.
Is the inspection result normal?
YES>>Check that the pin terminals and the connection of each connector are normal.
NO>>Repair or replace malfunctioning components.
Steering Wheel Turning Force Is Heavy or Light Nissan Pathfinder R53
Diagnosis Procedure
PERFORM SELF-DIAGNOSIS
CONSULT
Ignition switch ON.
Select “Self Diagnostic Result” mode of “EPS/DAST 3”.
Is a malfunctioning system displayed?
YES>>Check the DTC. Refer to DTC Index.
NO>>GO TO 2.
CHECK THE ILLUMINATION OF THE POWER STEERING WARNING LAMP
Check that the power steering warning lamp turns ON when ignition switch is placed ON. Then, power steering warning lamp turns OFF after the engine is started.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Perform trouble diagnosis of power steering warning lamp. Refer to Diagnosis Procedure.
CHECK THE EPS CONTROL UNIT SIGNAL (1)
CONSULT
Start the engine.
Turn steering wheel from full left stop to full right stop.
Select “ASSIST LEVEL” in “Data Monitor” mode of “EPS/DAST 3”.
Is the display value “100%”?
YES>>GO TO 6.
NO>>GO TO 4.
CHECK THE EPS CONTROL UNIT SIGNAL (2)
CONSULT
Select “BATTERY VOLT” in “Data Monitor” mode of “EPS/DAST 3”.
Is the display value “10.5 V” or more?
YES>>GO TO 5.
NO>>Perform trouble diagnosis of EPS control unit power supply and ground. Refer to Diagnosis Procedure.
CHECK THE EPS CONTROL UNIT SIGNAL (3)
CONSULT
Select “ASSIST LEVEL” in “Data Monitor” mode of “EPS/DAST 3”.
Stop the EPS system until the item in “Data Monitor” becomes “100%”.
Check that the symptom continues.
Does the symptom continue?
YES>>GO TO 6.
NO>>The assist torque decreases because of protection function. This is not malfunction. Inspection End.
CHECK THE EPS CONTROL UNIT SIGNAL (4)
CONSULT
Start the engine.
Turn steering wheel from full left stop to full right stop.
Select “STEERING TORQUE” in “Data Monitor” mode of “EPS/DAST 3”.
Perform the torque sensor inspection.
Monitor item Condition Display value STEERING TORQUE Steering wheel: Not steering (There is no steering force) Approx. 0 N·m Steering wheel: Right turn Positive value (Nm) Steering wheel: Left turn Negative value (Nm)
Is the inspection result normal?
YES>>GO TO 8.
NO>>GO TO 7.
CHECK EPS MOTOR
Perform the trouble diagnosis of EPS motor. Refer to DTC Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 8.
NO>>Repair or replace the specific malfunctioning part.
CHECK THE STEERING FORCE
Check the steering wheel turning force. Refer to Inspection.
Is the check result normal?
YES>>Inspection End.
NO>>It is possible that there is a mechanical malfunction. Check the steering system. Refer to Inspection.
Unbalance Steering Wheel Turning Force and Return Between Right and Left Nissan Pathfinder
Diagnosis Procedure
CHECK THE ILLUMINATION OF THE POWER STEERING WARNING LAMP
Check the power steering warning lamp while engine is running.
Does the power steering warning lamp turn OFF?
YES>>GO TO 2.
NO>>Refer to Diagnosis Procedure.
CHECK WHEEL ALIGNMENT
Check the wheel alignment. Refer to Inspection and Adjustment.
Is the inspection result normal?
YES>>GO TO 3.
NO>>Adjustment of wheel alignment. Refer to Inspection and Adjustment.
CHECK EPS CONTROL UNIT SIGNAL
CONSULT
Start the engine.
Turn steering wheel from full left stop to full right stop.
Select “STEERING TORQUE” in “Data Monitor” mode of “EPS/DAST 3”.
Perform the torque sensor inspection.
Monitor item Condition Display value STEERING TORQUE Steering wheel: Not steering (There is no steering force) Approx. 0 N·m Steering wheel: Right turn Positive value (Nm) Steering wheel: Left turn Negative value (Nm)
Is the inspection result normal?
YES>>GO TO 5.
NO>>GO TO 4.
CHECK EPS MOTOR
Perform the trouble diagnosis of EPS motor. Refer to DTC Diagnosis Procedure.
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair or replace the specific malfunctioning part.
CHECK STEERING WHEEL TURNING FORCE
Check the steering wheel turning force. Refer to Inspection.
Is the check result normal?
YES>>Inspection End.
NO>>It is possible that there is a mechanical malfunction. Check the steering system. Refer to Inspection.