Power Control System - Dtc/circuit Diagnosis

In this manual: Power Control System - Dtc/circuit Diagnosis
General Information — 8Engine :: Engine Mechanical — 19Engine Lubrication System - Precautions. Preparation — 1Engine Lubrication System - Lubrication System (System Description). Engine Oil Pressure (Basic Inspection). Service Data and Specifications (SDS) — 1Engine Cooling System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Engine Cooling System - Engine Coolant — 1Engine Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Engine Control System - Ecu Diagnosis Information — 1Ecu Diagnosis Information - Ecm ++ — 1Engine Control System - Basic Inspection — 1Basic Inspection - Diagnosis and Repair Workflow ++ — 1Basic Inspection - Basic Inspection ++ — 1Basic Inspection - Additional Service When Replacing Ecm ++ — 1Basic Inspection - Fuel Pressure Check ++ — 1Basic Inspection - How to Set Srt Code ++ — 1Basic Inspection - How to Erase Permanent Dtc ++ — 1Engine Control System - Dtc/circuit Diagnosis — 1Engine Control System - Symptom Diagnosis — 1Engine Control System - Periodic Maintenance — 1Engine Control System - Removal and Installation — 1Fuel System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Fuel System - Fuel System (Periodic Maintenance). Fuel Level Sensor Unit (Disassembly and Assembly) — 1Exhaust System - Precautions. Preparation — 1Exhaust System - Exhaust System (Periodic Maintenance). Exhaust System (Removal and Installation) — 1Starting System - Precautions. Preparation. Starter Motor (Service Data and Specifications (sds)) — 1Starting System - Diagnosis and Repair Work Flow — 1Starting System - Starting System (Symptom Diagnosis). Starter Motor (Removal and Installation) — 1Accelerator Control System - Precautions. Service Data and Specifications (SDS) — 1Accelerator Control System - Accelerator Pedal Assembly — 1Transmission & Driveline :: Transaxle & Transmission — 21Driveline - System Description — 1Transfer: Ty92b - Ecu Diagnosis Information. Awd Control Unit ++ — 1Driveline - Basic Inspection — 1Driveline - Dtc/circuit Diagnosis — 1Driveline - Symptom Diagnosis — 1Driveline - Removal and Installation — 1Transfer: Ty92b - Unit Removal and Installation. Transfer Assembly ++ — 1Driveline - Unit Disassembly and Assembly — 1Driveline - Basic Inspection — 1Driveline - Removal and Installation — 1Driveline - Unit Disassembly and Assembly — 1Front Axle - Precautions. Preparation — 1Front Axle - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Front Axle - Front Drive Shaft Boot — 1Front Axle - Front Drive Shaft — 1Rear Axle - Precautions. Preparation. Service Data and Specifications (SDS) — 1Rear Axle - Noise, Vibration and Harshness (nvh) Troubleshooting — 1Rear Axle - Rear Drive Shaft — 1Suspension :: Front Suspension — 7Rear Suspension - Precautions. Preparation — 1Rear Suspension - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Rear Suspension - Rear Suspension Assembly — 1Road Wheels & Tires - Precautions — 1Road Wheels & Tires - Preparation. Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Road Wheels & Tires - System — 1Brakes :: Brake System — 9Parking Brake System - Precautions. Preparation — 1Parking Brake System - System — 1Vdc/tcs/abs - Precautions ++ — 1Brake Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Dtc/circuit Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Steering :: Steering System — 9Steering Control System - Precautions — 1Steering Control System - System — 1Steering Control System - Eps Control Unit (Ecu Diagnosis Information. Removal and Installation) — 1Restraints :: Seat Belt — 7Srs Air Bag - Precautions. Preparation — 1Srs Air Bag - Collision Diagnosis — 1Srs Air Bag - Occupant Classification System — 1Srs Air Bag Control System - Precautions — 1Srs Air Bag Control System - System — 1Srs Air Bag Control System - Diagnosis Sensor Unit — 1Srs Air Bag Control System - Inspection and Adjustment — 1Ventilation, Heater & Air Conditioner :: Ventilation System — 6Heater & Air Conditioning System - Precautions — 1Heater & Air Conditioning System - Preparation — 1Heater & Air Conditioning System - Component Parts — 1Heater & Air Conditioning System - Diagnosis and Repair Work Flow — 1Heater & Air Conditioning System - Compressor — 1Heater & Air Conditioning System - Cooler Pipe and Hose — 1Heater & Air Conditioning System - Condenser. Condenser — 1Heater & Air Conditioning System - Heating and Cooling Unit Assembly — 1Heater & Air Conditioning System - Service Data and Specifications (SDS) — 1Heater & Air Conditioning Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1Heater & Air Conditioning Control System - Ecu Diagnosis Information — 1Heater & Air Conditioning Control System - Basic Inspection — 1Heater & Air Conditioning Control System - Dtc/circuit Diagnosis — 1Heater & Air Conditioning Control System - Symptom Diagnosis — 1Heater & Air Conditioning Control System - Removal and Installation — 1Body Interior :: Interior — 8Instrument Panel - Precautions. Preparation. Clip List — 1Instrument Panel - Squeak and Rattle Trouble Diagnoses — 1Instrument Panel - Cluster Lid C — 1Seat - Precautions — 1Seat - Preparation. Clip List — 1Seat - Component Parts — 1Seat - System — 1Seat - Diagnosis and Repair Work Flow — 1Seat - Front Seat — 1Seat - Second Row Seats — 1Seat - Third Row Seats — 1Seat - Front Seat — 1Seat - Second Row Seat — 1Seat - Third Row Seat — 1Automatic Drive Positioner - Precautions. Preparation — 1Automatic Drive Positioner - System — 1Automatic Drive Positioner - Diagnosis and Repair Work Flow — 1Automatic Drive Positioner - Inspection and Adjustment — 1Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock — 38Security Control System - Precautions — 1Security Control System - System — 1Security Control System - Ecm, Bcm, Intelligent Key Unit, Ipdm E/r — 1Security Control System - Vehicle Security System Cannot Be Set — 1Glass & Window System - Precautions. Preparation — 1Glass & Window System - Squeak and Rattle Trouble Diagnoses — 1Power Window Control System - Precautions. Preparation — 1Power Window Control System - Power Supply and Ground Circuit — 1Power Window Control System - Power Window Motor Circuit — 1Power Window Control System - Front Power Window Rh Alone Does Not Operate — 1Power Window Control System - Rear Lh Side Power Window Alone Does Not Operate — 1Power Window Control System - Rear Rh Side Power Window Alone Does Not Operate — 1Roof - Precautions. Preparation — 1Roof - Power Supply and Ground Circuit — 1Roof - Moonroof Switch Assembly — 1Roof - Lin Communication Circuit — 1Roof - Auto Operation Does Not Operate — 1Roof - Anti-Pinch Function Does Not Operate — 1Exterior - Precautions. Preparation. Clip List (Preparation) — 1Exterior - Squeak and Rattle Trouble Diagnoses — 1Exterior - Fender Protector — 1Exterior - Over Fender — 1Exterior - Under Cover — 1Exterior - Roof Side Rail — 1Body Repair - Service Information — 1Service Information - Sheet Metal Work ++ — 1Service Information - Body Welding and Precautions ++ — 1Service Information - Safety and Health ++ — 1Service Information - Repairing Procedures and Precautions ++ — 1Body Repair - Precaution — 1Body Repair - Preparation — 1Body Repair - Removal and Installation — 1Driver Controls :: Mirrors — 8Exterior Lighting System - System Description — 1System Description - Component Parts ++ — 1Exterior Lighting System - Basic Inspection — 1Exterior Lighting System - Dtc/circuit Diagnosis — 1Exterior Lighting System - Symptom Diagnosis — 1Exterior Lighting System - Periodic Maintenance — 1Exterior Lighting System - Removal and Installation — 1Interior Lighting System - Precautions. Preparation — 1Interior Lighting System - Component Parts. Interior Lighting System — 1Interior Lighting System - System — 1Interior Lighting System - Diagnosis and Repair Work Flow — 1Interior Lighting System - Interior Lighting System Symptoms (Symptom Diagnosis). Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Interior Lighting System - Foot Lamp — 1Wiper & Washer - Precautions — 1Wiper & Washer - Preparation. Bcm, Ipdm E/r (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Wiper & Washer - System — 1Wiper & Washer - Diagnosis and Repair Work Flow — 1Defogger - Precautions. Bcm, A/c Auto Amp. (Ecu Diagnosis Information) — 1Defogger - Diagnosis and Repair Work Flow — 1Horn - Precautions — 1Electrical & Power Control :: Power Outlet — 13Body Control System - Precautions. Preparation — 1Body Control System - Component Parts — 1Body Control System - System — 1Body Control System - Diagnosis System (bcm) — 1Body Control System - Bcm — 1Lan System - System Description — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - Removal and Installation — 1Charging System - Precautions. Preparation. Ecm, Ipdm E/r (Ecu Diagnosis Information) — 1Charging System - Diagnosis and Repair Work Flow — 1Charging System - Charging System (Symptom Diagnosis). Generator (Removal and Installation). Service Data and Specifications (SDS) — 1Power Supply, Ground & Circuit Elements - Precautions. Preparation. Service Data and Specifications (SDS) — 1Driver Information & Multimedia :: Meter, Warning Lamp & Indicator — 25Warning Chime System - Application Notice (How to Use This Manual). Precautions — 1Warning Chime System - System — 1Warning Chime System - Diagnosis System (combination Meter) — 1Warning Chime System - Bcm, Combination Meter (Ecu Diagnosis Information). Diagnosis and Repair Work Flow (Basic Inspection) — 1Sonar System - Precautions. Preparation — 1Sonar System - Sonar Control Unit — 1Dtc/circuit Diagnosis - B2720 Corner Sensor [rl] ++ — 1Audio, Visual & Navigation System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Multi Av (av Control Unit) ++ — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Symptom Diagnosis - Multi Av System ++ — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Cruise Control & Driver Assistance :: Cruise Control System — 17Driver Assistance System - System Description — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Driver Assistance System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1System Description - Handling Precaution ++ — 1Driver Assistance System - Ecu Diagnosis Information — 1Driver Assistance System - Basic Inspection — 1Basic Inspection - Distance Sensor Alignment ++ — 1Basic Inspection - Camera Aiming Adjustment ++ — 1Basic Inspection - Action Test ++ — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Laser/radar (distance Sensor) ++ — 1Dtc/circuit Diagnosis - Lane Camera (front Camera Unit) ++ — 1Driver Assistance System - Symptom Diagnosis — 1Driver Assistance System - Removal and Installation — 1Driver Assistance System - System Description — 1System Description - System ++ — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Drive Mode System - Precautions — 1Drive Mode System - Component Parts. Drive Mode System — 1Drive Mode System - System — 1Drive Mode System - Diagnosis and Repair Work Flow — 1Drive Mode System - Drive Mode Select Switch Circuit — 1Maintenance - Precautions. Preparation — 1Maintenance - General Maintenance — 1Maintenance - Periodic Maintenance — 1Maintenance - Recommended Fluids and Lubricants — 1Maintenance - Engine Maintenance — 1Maintenance - Chassis and Body Maintenance — 1Engine Lubrication System - Periodic Maintenance — 1Engine Lubrication System - Removal and Installation — 1Engine Cooling System - System Description — 1Engine Cooling System - Removal and Installation — 1Engine Control System - Vq35dd — 1Fuel System - Removal and Installation — 1Starting System - System Description — 1Starting System - Dtc/circuit Diagnosis — 1Driveline - Transfer: Ty92b — 1Driveline - Rear Propeller Shaft: 3fcj-Cvj — 1Driveline - Rear Final Drive: R145 — 1Front Axle - Periodic Maintenance — 1Front Axle - Removal and Installation — 1Rear Axle - Periodic Maintenance — 1Rear Axle - Removal and Installation — 1Rear Suspension - Removal and Installation — 1Road Wheels & Tires - System Description — 1Road Wheels & Tires - Basic Inspection — 1Road Wheels & Tires - Dtc/circuit Diagnosis — 1Road Wheels & Tires - Symptom Diagnosis — 1Road Wheels & Tires - Periodic Maintenance — 1Road Wheels & Tires - Removal and Installation — 1Parking Brake System - System Description — 1Parking Brake System - Basic Inspection — 1Parking Brake System - Dtc/circuit Diagnosis — 1Parking Brake System - Symptom Diagnosis — 1Parking Brake System - Removal and Installation — 1Brake Control System - Vdc/tcs/abs — 1Brake Control System - Automatic Brake Hold — 1Brake Control System - Automatic Emergency Braking — 1Brake Control System - Rear Automatic Braking — 1Steering Control System - System Description — 1Steering Control System - Basic Inspection — 1Steering Control System - Dtc/circuit Diagnosis — 1Steering Control System - Symptom Diagnosis — 1Srs Air Bag - Removal and Installation — 1Srs Air Bag Control System - System Description — 1Srs Air Bag Control System - Basic Inspection — 1Srs Air Bag Control System - Symptom Diagnosis — 1Heater & Air Conditioning System - Symptom Diagnosis — 1Heater & Air Conditioning System - Periodic Maintenance — 1Heater & Air Conditioning Control System - Automatic Air Conditioning — 1Instrument Panel - Removal and Installation — 1Instrument Panel - Unit Disassembly and Assembly — 1Seat - Ecu Diagnosis Information — 1Seat - Dtc/circuit Diagnosis — 1Seat - Symptom Diagnosis — 1Automatic Drive Positioner - System Description — 1Automatic Drive Positioner - Ecu Diagnosis Information — 1Automatic Drive Positioner - Dtc/circuit Diagnosis — 1Automatic Drive Positioner - Symptom Diagnosis — 1Automatic Drive Positioner - Removal and Installation — 1Security Control System - System Description — 1Security Control System - Basic Inspection — 1Security Control System - Dtc/circuit Diagnosis — 1Security Control System - Symptom Diagnosis — 1Security Control System - Removal and Installation — 1Glass & Window System - Removal and Installation — 1Power Window Control System - System Description — 1Power Window Control System - Ecu Diagnosis Information — 1Power Window Control System - Basic Inspection — 1Power Window Control System - Dtc/circuit Diagnosis — 1Power Window Control System - Symptom Diagnosis — 1Power Window Control System - Removal and Installation — 1Roof - System Description — 1Roof - Ecu Diagnosis Information — 1Roof - Basic Inspection — 1Roof - Dtc/circuit Diagnosis — 1Roof - Symptom Diagnosis — 1Roof - Removal and Installation — 1Exterior - System Description — 1Exterior - Removal and Installation — 1Body Repair - Repair Information — 1Exterior Lighting System - Led Headlamp — 1Interior Lighting System - Dtc/circuit Diagnosis — 1Interior Lighting System - Removal and Installation — 1Wiper & Washer - System Description — 1Wiper & Washer - Dtc/circuit Diagnosis — 1Wiper & Washer - Symptom Diagnosis — 1Wiper & Washer - Removal and Installation — 1Defogger - System Description — 1Defogger - Dtc/circuit Diagnosis — 1Defogger - Symptom Diagnosis — 1Defogger - Removal and Installation — 1Horn - Removal and Installation — 1Body Control System - Basic Inspection — 1Body Control System - Dtc/circuit Diagnosis — 1Body Control System - Symptom Diagnosis — 1Body Control System - Removal and Installation — 1Lan System - Can Fundamental — 1Lan System - Can — 1Lan System - Can Gateway — 1Power Control System - Ipdm E/r — 1Power Control System - Power Distribution System — 1Charging System - System Description — 1Charging System - Dtc/circuit Diagnosis — 1Power Supply, Ground & Circuit Elements - System Description — 1Power Supply, Ground & Circuit Elements - Basic Inspection — 1Power Supply, Ground & Circuit Elements - Removal and Installation — 1Warning Chime System - System Description — 1Warning Chime System - Dtc/circuit Diagnosis — 1Warning Chime System - Symptom Diagnosis — 1Sonar System - System Description — 1Sonar System - Basic Inspection — 1Sonar System - Dtc/circuit Diagnosis — 1Sonar System - Symptom Diagnosis — 1Sonar System - Removal and Installation — 1Audio, Visual & Navigation System - Nissanconnect — 1Audio, Visual & Navigation System - Intelligent Around View Monitor System — 1Audio, Visual & Navigation System - Rear View Monitor System — 1Audio, Visual & Navigation System - Telematics System — 1Driver Assistance System - Adas Control Unit 2 — 1Driver Assistance System - Driver Assistance System — 1Driver Assistance System - Chassis Control — 1Drive Mode System - Removal and Installation — 1Dtc/circuit Diagnosis (C053c Wheel Speed Sensor ... U2141 Can Comm Circuit) — 1Dtc/circuit Diagnosis (P0011 Intake Valve Timing Control ... P0111 Iat Sensor) — 1Dtc/circuit Diagnosis (P0116 Engine Coolant Temperature Sensor ... P025b Fuel Pump Module a) — 1Dtc/circuit Diagnosis (P026b Injection Timing ... P0420 Three Way Catalyst Function) — 1Dtc/circuit Diagnosis (P0441 Evap Control System ... P0524 Engine Oil Pressure) — 1Dtc/circuit Diagnosis (P0532 A/c Refrigerant Pressure Sensor ... P064d Ecm) — 1Dtc/circuit Diagnosis (P06da Engine Oil Pressure Control Solenoid Valve ... P1217 Engine Over Temperature) — 1Dtc/circuit Diagnosis (P1220 Fuel Pump Control Module (fpcm) ... P1574 Ascd Vehicle Speed Sensor) — 1Dtc/circuit Diagnosis (P1575 Brake Switch ... P2101 Electric Throttle Control Function) — 1Dtc/circuit Diagnosis (P2118 Throttle Control Motor ... P34ac Electric Intake Valve Timing Control Actuator) — 1Dtc/circuit Diagnosis (Active Grille Shutter ... High Pressure Fuel Pump) — 1Dtc/circuit Diagnosis (Ignition Signal ... Variable Induction Air System) — 14012 C1040 Emergency Brake — 14013 C106a Wheel Sensor — 14014 C1078-55 Not Configuration — 14015 C10b4-98 Overheat — 14016 B1001 Lap Pre-Tensioner Lh — 14017 B0001 Driver Air Bag Module — 14018 B100e Knee Air Bag Module Rh — 14019 B142x Collision Detection — 1Dtc/circuit Diagnosis (B20c7-11 A/c Clutch ... B24a6-11 in-Vehicle Sensor) — 1Dtc/circuit Diagnosis (B24a6-15 in-Vehicle Sensor ... U2140-87 Can Comm Err (ecm)) — 1Dtc/circuit Diagnosis (C1f00-1c Control Unit ... C1f04-61 Brake Sw/stop Lamp Sw) — 1Dtc/circuit Diagnosis (C1f05-49 Front Camera Unit ... C1f70-87 Ethernet Circuit) — 1
63steps
~378min
4/5difficulty
Done 0 of 63
  • B1200-54 Ipdm E/r
  • B120e-04 Ipdm E/r
  • B120e-42 Ipdm E/r
  • B12a3-73 Fuel Pump Off Circuit
  • B20a1-16 Ipdm E/r
  • B20dd-73 Ign Relay on Circ
  • B20de-72 Ign Relay Off Circ
  • U0073-00 Control Module Comm Bus a Off
  • U1000-01 Can Comm Circuit
  • U2004-87 Can Comm Err (ccm/st Angle Sensor)
  • Power Supply and Ground Circuit

B1200-54 Ipdm E/r Nissan Pathfinder 2026

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC detection condition
B1200-54

IPDM E/R

(Intelligent power distribution module engine room)
[NOT CONFIGURED] Diagnosis condition When ignition switch is ON
Signal (terminal) —
Threshold Configuration is not performed
Diagnosis delay time 1 second or more

POSSIBLE CAUSE

  • Configuration is not performed.

  • IPDM E/R

FAIL-SAFE

—

DTC Confirmation Procedure

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Select “Self Diagnostic Result” mode of “IPDM E/R”.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

PERFORM CONFIGURATION (IPDM E/R)

CONSULT

  1. Perform configuration (IPDM E/R). Refer to Work Procedure.

  2. Perform DTC confirmation procedure. Refer to DTC Confirmation Procedure.

Is DTC detected?

YES>>

Replace IPDM E/R. Refer to Removal and Installation.

NO>>

Inspection End.

B120e-04 Ipdm E/r Nissan Pathfinder 2022

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC detection condition
B120E-04

IPDM E/R

(Intelligent power distribution module engine room)
[SYSTEM INTERNAL MALFUNCTN] Diagnosis condition When ignition switch is ON
Signal (terminal) —
Threshold EEPROM in IPDM E/R is malfunctioning
Diagnosis delay time 1 second or more

POSSIBLE CAUSE

IPDM E/R

FAIL-SAFE

—

DTC Confirmation Procedure

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Select “Self Diagnostic Result” mode of “IPDM E/R”.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

REPLACE IPDM E/R

Replace IPDM E/R. Refer to Removal and Installation.

NO>>

Inspection End.

B120e-42 Ipdm E/r Nissan Pathfinder 2026

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC detection condition
B120E-42

IPDM E/R

(Intelligent power distribution module engine room)
[MEMORY ERROR] 1 Diagnosis condition When the power consumption control of IPDM E/R changes from normal mode (wake-up) to low power consumption mode (sleep)
Signal (terminal) —
Threshold Configuration writing is incomplete to ROM
Diagnosis delay time —
2 Diagnosis condition —
Signal (terminal) —
Threshold IPDM E/R damage counter has maximum value
Diagnosis delay time —
3 Diagnosis condition —
Signal (terminal) —
Threshold LIN-BUS error
Diagnosis delay time —

POSSIBLE CAUSE

  • IPDM E/R

  • Harness or connectors

  • Front combination lamp LH/RH

    • LED headlamp control module

    • Harness

  • Battery current sensor

FAIL-SAFE

—

DTC Confirmation Procedure

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Perform configuration (IPDM E/R). Refer to Work Procedure.

  3. Ignition switch OFF and wait for 1 minute with the front LH door opened.

  4. Ignition switch ON.

  5. Select “Self Diagnostic Result” mode of “IPDM E/R”.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK IPDM E/R DAMAGE

CONSULT

  1. Ignition switch ON.

  2. Select the following item in “Data Monitor” mode of “IPDM E/R”:

    • T LAMP LH CIRC MALFUNCTN

    • T LAMP RH CIRC MALFUNCTN

    • Fr fog lamp (LH) circ malfunctn

    • F FOG RH CIRC MALFUNCTN

  3. Check the monitor status.

    Monitor itemMonitor status
    T LAMP LH CIRC MALFUNCTN 0
    1
    T LAMP RH CIRC MALFUNCTN 0
    1
    Fr fog lamp (LH) circ malfunctn 0
    1
    F FOG RH CIRC MALFUNCTN 0
    1

What is the monitor status?

“0”>>

GO TO 2.

“1”>>

Replace IPDM E/R. Refer to Removal and Installation.

CHECK LIN-BUS (HEADLAMP) ERROR

Check headlamp warning is displayed by information display.

Is headlamp warning displayed?

YES>>

Perform trouble diagnosis for headlamp. Refer to Diagnosis Procedure (headlamp RH) and Diagnosis Procedure (headlamp LH).

NO>>

GO TO 3.

CHECK LIN-BUS (BATTERY CURRENT SENSOR) ERROR

CONSULT

  1. Select "Battery current sen value (LIN)" in “Data Monitor” mode of “IPDM E/R”.

  2. Check the monitor value.

    Monitor itemMonitor value
    Battery current sen value (LIN) 455.34 A

What is the monitor value?

“455.34 A”>>

Perform trouble diagnosis for battery current sensor. Refer to DTC Diagnosis Procedure.

Except “455.34 A”>>

Inspection End.

B12a3-73 Fuel Pump Off Circuit Nissan Pathfinder

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC detection condition
B12A3-73

Fuel pump Off circuit

(Fuel pump Off circuit)
[CIRC SHORT TO BATTERY] Diagnosis condition When ignition switch is ON
Signal (terminal) —
Threshold —
Diagnosis delay time 1 second or more

POSSIBLE CAUSE

  • Fusible link

  • Fuse

  • Harness or connectors (battery power supply circuit is open or shorted to ground)

  • IPDM E/R

FAIL-SAFE

—

DTC Confirmation Procedure

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch OFF.

  2. Ignition switch ON.

  3. Select “Self Diagnostic Result” mode of “IPDM E/R”.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK FUSE AND FUSIBLE LINK

  1. Ignition switch OFF.

  2. Check that the following IPDM E/R fuse and fusible link is not blown (open):

    Signal nameFuse and Fusible link No.Capacity
    Battery power supply H 100 A
    F 100 A
    Ignition power supply 85 20 A

Is the fuse and fusible link blown (open)?

YES>>

Replace the blown (open) fuse or fusible link after repairing the affected circuit if a fuse or fusible link is blown (open).

NO>>

GO TO 2.

CHECK BATTERY POWER SUPPLY VOLTAGE

  1. Disconnect IPDM E/R connector.

  2. Check voltage between IPDM E/R harness connector and the ground.

    +-

    Voltage

    (Approx.)
    IPDM E/R
    ConnectorTerminal
    E118 2 Ground Battery voltage

Is the inspection result normal?

YES>>

Replace IPDM E/R. Refer to Removal and Installation.

NO>>

Repair the battery power supply circuit.

B20a1-16 Ipdm E/r Nissan Pathfinder R53

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC detection condition
B20A1-16

IPDM E/R

(Intelligent power distribution module engine room)
[CIRC VOLT BELOW THRESHOLD] Diagnosis condition When ignition switch is OFF
Signal (terminal) Battery power supply voltage (terminal #1, #2 and #81)
Threshold Voltage do not match
Diagnosis delay time 1 second or more

POSSIBLE CAUSE

  • Fusible link

  • Harness or connectors (battery power supply circuit is open or shorted to ground)

  • IPDM E/R

FAIL-SAFE

—

DTC Confirmation Procedure

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Ignition switch OFF and wait for 1 second or more.

  3. Ignition switch ON.

  4. Select “Self Diagnostic Result” mode of “IPDM E/R”.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK FUSIBLE LINK

  1. Ignition switch OFF.

  2. Check that the following IPDM E/R fusible links are not blown (open):

    Signal nameFusible link No.Capacity
    Battery power supply H 100 A
    F
    D
    O 40 A

Is the fusible link blown (open)?

YES>>

Replace the blown (open) fusible link after repairing the affected circuit if a fusible links are blown (open).

NO>>

GO TO 2.

CHECK BATTERY POWER SUPPLY VOLTAGE

  1. Disconnect IPDM E/R connector.

  2. Check voltage between IPDM E/R harness connector and the ground.

    +-

    Voltage

    (Approx.)
    IPDM E/R
    ConnectorTerminal
    E118 1 Ground Battery voltage
    2
    E77 81

Is the inspection result normal?

YES>>

Replace IPDM E/R. Refer to Removal and Installation.

NO>>

Repair the battery power supply circuit.

B20dd-73 Ign Relay on Circ Nissan Pathfinder SUV

DTC Description

  • The IPDM E/R operates the ignition relay when it receives an ignition switch ON signal from the BCM via CAN communication.

  • Turn the ignition relay OFF by pressing the push-button ignition switch once when the Nissan Pathfinder vehicle speed is 4 km/h or less.

  • Turn the ignition relay OFF with the following operation when the Nissan Pathfinder vehicle speed is more than 4 km/h or when an abnormal condition occurs in CAN communication from the combination meter (emergency OFF):

    • Press and hold the push-button ignition switch for 2 seconds or more.

    • Press the push-button ignition switch 3 times within 1.5 seconds.

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC detection condition
B20DD-73

IGN RELAY ON CIRC

(Ignition relay on circuit)
[ACTUATOR STUCK CLOSED] Diagnosis condition When ignition switch is OFF
Signal (terminal) CPU monitors the status at the contact and excitation coil circuits of the ignition relay inside it
Threshold The ignition relay ON is detected
Diagnosis delay time 1 second or more

POSSIBLE CAUSE

IPDM E/R

FAIL-SAFE

—

DTC Confirmation Procedure

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Ignition switch OFF and wait for 1 second or more.

  3. Ignition switch ON.

  4. Select “Self Diagnostic Result” mode of “IPDM E/R”.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK IGNITION RELAY POWER SUPPLY CIRCUIT 1

CONSULT

  1. Ignition switch ON.

  2. Select “Self Diagnostic Result” mode of “IPDM E/R”.

  3. Remove fuse [No. 73 (10A)] at the downstream of ignition relay in the IPDM E/R, and check the change in “Self Diagnostic Result”.

Is it now a past malfunction?

YES>>

Perform an inspection of the downstream circuit of fuse [No. 73 (10A)] at the downstream of ignition relay in IPDM E/R.

NO>>

GO TO 2.

CHECK IGNITION RELAY POWER SUPPLY CIRCUIT 2

CONSULT

  1. Return fuse [No. 73 (10A)] downstream of ignition relay in the IPDM E/R back to the original position.

  2. Remove fuse [No. 71 (10A)] at the downstream of ignition relay in the IPDM E/R, and check the change in “Self Diagnostic Result”.

Is it now a past malfunction?

YES>>

Perform an inspection of the downstream circuit of fuse [No. 71 (10A)] at the downstream of ignition relay in IPDM E/R.

NO>>

GO TO 3.

CHECK IGNITION RELAY POWER SUPPLY CIRCUIT 3

CONSULT

  1. Return fuse [No. 71 (10A)] downstream of ignition relay in the IPDM E/R back to the original position.

  2. Remove fuse [No. 81 (15A)] at the downstream of ignition relay in the IPDM E/R, and check the change in “Self Diagnostic Result”.

Is it now a past malfunction?

YES>>

Perform an inspection of the downstream circuit of fuse [No. 81 (15A)] at the downstream of ignition relay in the IPDM E/R.

NO>>

GO TO 4.

CHECK IGNITION RELAY POWER SUPPLY CIRCUIT 4

CONSULT

  1. Return fuse [No. 81 (15A)] downstream of ignition relay in the IPDM E/R back to the original position.

  2. Remove fuse [No. 85 (20A)] at the downstream of ignition relay in the IPDM E/R, and check the change in “Self Diagnostic Result”.

Is it now a past malfunction?

YES>>

Perform an inspection of the downstream circuit of fuse [No. 85 (20A)] at the downstream of ignition relay in the IPDM E/R.

NO>>

Replace IPDM E/R. Refer to Removal and Installation.

B20de-72 Ign Relay Off Circ Nissan Pathfinder 2026

DTC Description

  • The IPDM E/R operates the ignition relay when it receives an ignition switch ON signal from the BCM via CAN communication.

  • Turn the ignition relay OFF by pressing the push-button ignition switch once when the Nissan Pathfinder vehicle speed is 4 km/h or less.

  • Turn the ignition relay OFF with the following operation when the Nissan Pathfinder vehicle speed is more than 4 km/h or when an abnormal condition occurs in CAN communication from the combination meter (emergency OFF):

    • Press and hold the push-button ignition switch for 2 seconds or more.

    • Press the push-button ignition switch 3 times within 1.5 seconds.

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC detection condition
B20DE-72

IGN RELAY OFF CIRC

(Ignition relay OFF circuit)
[ACTUATOR STUCK OPEN] Diagnosis condition When ignition switch is ON
Signal (terminal) CPU monitors the status at the contact and excitation coil circuits of the ignition relay inside it
Threshold The ignition relay OFF is detected
Diagnosis delay time 1 second or more

POSSIBLE CAUSE

IPDM E/R

FAIL-SAFE

—

DTC Confirmation Procedure

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON.

  2. Select “Self Diagnostic Result” mode of “IPDM E/R”.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

REPLACE IPDM E/R

Replace IPDM E/R. Refer to Removal and Installation.

>>

Inspection End.

U0073-00 Control Module Comm Bus a Off Nissan Pathfinder 2026

DTC Description

CAN (Controller Area Network) is a serial communication line for real time applications. It is an on-Nissan Pathfinder vehicle multiplex communication line with high data communication speed and excellent error detection ability. Modern Nissan Pathfinder vehicle is equipped with many electronic control unit, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with 2 communication lines (CAN High-line, CAN Low-line) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only.

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC detection condition
U0073-00

Control module comm Bus A Off

(Control module communication Bus A Off)
[NO SUBTYPE INFO] Diagnosis condition When ignition switch is ON
Signal (terminal) CAN communication signal
Threshold When IPDM E/R cannot communicate CAN communication signal
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

When CAN communication with the ECM and BCM is impossible, the IPDM E/R performs fail-safe control. After CAN communication recovers normally, it also returns to normal control.

DTC Confirmation Procedure

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 2 seconds or more.

  2. Select “Self Diagnostic Result” mode of “IPDM E/R”.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK CAN COMMUNICATION SYSTEM

Perform trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

>>

Inspection End.

U1000-01 Can Comm Circuit Nissan Pathfinder SUV

DTC Description

Description

CAN (Controller Area Network) is a serial communication line for real time applications. It is an on-Nissan Pathfinder vehicle multiplex communication line with high data communication speed and excellent error detection ability. Modern Nissan Pathfinder vehicles are equipped with many electronic control units and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with 2 communication lines (CAN-High line, CAN-Low line) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only. Refer to CAN Communication Signal Chart.

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC Detection Condition
U1000-01

CAN COMM CIRCUIT

(CAN communication circuit)
[ELECTRICAL MALFUNCTION] Diagnosis condition Ignition switch is ON.
Signal (terminal) —
Threshold —
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

—

DTC Confirmation Procedure

PERFORM DTC CONFIRMATION

CONSULT

  1. Ignition switch ON.

  2. Ignition switch OFF and wait 1 second or more.

  3. Ignition switch ON.

  4. Select “Self Diagnostic Result” mode of “IPDM E/R”.

  5. Check DTC.

Is DTC U1000-01 displayed?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair, refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

SELF DIAGNOSTIC RESULT

CONSULT

  1. Ignition switch ON and wait for 2 seconds or more.

  2. Select “Self Diagnostic Result” mode of “IPDM E/R”.

  3. Check DTC.

Is DTC “U1000-01” displayed?

YES>>

Refer to Trouble Diagnosis Flow Chart.

NO>>

To check malfunction symptom before repair, refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

U2004-87 Can Comm Err (ccm/st Angle Sensor) Nissan Pathfinder 5th Gen

DTC Description

CAN (Controller Area Network) is a serial communication line for real time applications. It is an on-Nissan Pathfinder vehicle multiplex communication line with high data communication speed and excellent error detection ability. Modern Nissan Pathfinder vehicle is equipped with many electronic control unit, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with 2 communication lines (CAN-High line, CAN-Low line) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only.

DTC DETECTION LOGIC

DTC No.

CONSULT screen items

(Trouble diagnosis content)
DTC detection condition
U2004-87

CAN comm err (CCM/ST angle sensor)

[Controller area network communication error (chassis control module/steering angle sensor)]
[MISSING MESSAGE] Diagnosis condition When ignition switch is ON
Signal (terminal) CAN communication signal
Threshold When IPDM E/R cannot communicate CAN communication signal
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

—

DTC Confirmation Procedure

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON and wait for 2 seconds or more.

  2. Select “Self Diagnostic Result” mode of “IPDM E/R”.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End.

DTC Diagnosis Procedure

CHECK CAN COMMUNICATION SYSTEM

Perform trouble diagnosis for CAN communication system. Refer to Trouble Diagnosis Flow Chart.

>>

Inspection End.

Power Supply and Ground Circuit Nissan Pathfinder SUV

Diagnosis Procedure

CHECK FUSIBLE LINKS

Check that the following IPDM E/R fusible links are not blown:

TerminalSignal nameFusible link Nos.Capacity
1 Battery H 100 A
2 F
81 D
O 40 A

Is the fusible link blown?

YES>>

Replace the blown fusible link after repairing the affected circuit.

NO>>

GO TO 2

CHECK POWER SUPPLY CIRCUIT

  1. Disconnect IPDM E/R connector.

  2. Check voltage between IPDM E/R harness connector and ground.

    IPDM E/R—

    Voltage

    (Approx.)
    ConnectorTerminal
    E118 1 Ground Battery voltage
    2
    E77 81

Is the inspection result normal?

YES>>

GO TO 3

NO>>

Repair harness or connectors.

CHECK GROUND CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect IPDM E/R connector.

  3. Check continuity between IPDM E/R harness connector and ground.

IPDM E/R—Continuity
ConnectorTerminal
E120 12 Ground Yes
E119 31
E121 47

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Repair harness or connectors.