System Description - System ++

In this manual: System Description - System ++
General Information — 8Engine :: Engine Mechanical — 19Engine Lubrication System - Precautions. Preparation — 1Engine Lubrication System - Lubrication System (System Description). Engine Oil Pressure (Basic Inspection). Service Data and Specifications (SDS) — 1Engine Cooling System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Engine Cooling System - Engine Coolant — 1Engine Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Engine Control System - Ecu Diagnosis Information — 1Ecu Diagnosis Information - Ecm ++ — 1Engine Control System - Basic Inspection — 1Basic Inspection - Diagnosis and Repair Workflow ++ — 1Basic Inspection - Basic Inspection ++ — 1Basic Inspection - Additional Service When Replacing Ecm ++ — 1Basic Inspection - Fuel Pressure Check ++ — 1Basic Inspection - How to Set Srt Code ++ — 1Basic Inspection - How to Erase Permanent Dtc ++ — 1Engine Control System - Dtc/circuit Diagnosis — 1Engine Control System - Symptom Diagnosis — 1Engine Control System - Periodic Maintenance — 1Engine Control System - Removal and Installation — 1Fuel System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Fuel System - Fuel System (Periodic Maintenance). Fuel Level Sensor Unit (Disassembly and Assembly) — 1Exhaust System - Precautions. Preparation — 1Exhaust System - Exhaust System (Periodic Maintenance). Exhaust System (Removal and Installation) — 1Starting System - Precautions. Preparation. Starter Motor (Service Data and Specifications (sds)) — 1Starting System - Diagnosis and Repair Work Flow — 1Starting System - Starting System (Symptom Diagnosis). Starter Motor (Removal and Installation) — 1Accelerator Control System - Precautions. Service Data and Specifications (SDS) — 1Accelerator Control System - Accelerator Pedal Assembly — 1Transmission & Driveline :: Transaxle & Transmission — 21Driveline - System Description — 1Transfer: Ty92b - Ecu Diagnosis Information. Awd Control Unit ++ — 1Driveline - Basic Inspection — 1Driveline - Dtc/circuit Diagnosis — 1Driveline - Symptom Diagnosis — 1Driveline - Removal and Installation — 1Transfer: Ty92b - Unit Removal and Installation. Transfer Assembly ++ — 1Driveline - Unit Disassembly and Assembly — 1Driveline - Basic Inspection — 1Driveline - Removal and Installation — 1Driveline - Unit Disassembly and Assembly — 1Front Axle - Precautions. Preparation — 1Front Axle - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Front Axle - Front Drive Shaft Boot — 1Front Axle - Front Drive Shaft — 1Rear Axle - Precautions. Preparation. Service Data and Specifications (SDS) — 1Rear Axle - Noise, Vibration and Harshness (nvh) Troubleshooting — 1Rear Axle - Rear Drive Shaft — 1Suspension :: Front Suspension — 7Rear Suspension - Precautions. Preparation — 1Rear Suspension - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Rear Suspension - Rear Suspension Assembly — 1Road Wheels & Tires - Precautions — 1Road Wheels & Tires - Preparation. Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Road Wheels & Tires - System — 1Brakes :: Brake System — 9Parking Brake System - Precautions. Preparation — 1Parking Brake System - System — 1Vdc/tcs/abs - Precautions ++ — 1Brake Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Dtc/circuit Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Steering :: Steering System — 9Steering Control System - Precautions — 1Steering Control System - System — 1Steering Control System - Eps Control Unit (Ecu Diagnosis Information. Removal and Installation) — 1Restraints :: Seat Belt — 7Srs Air Bag - Precautions. Preparation — 1Srs Air Bag - Collision Diagnosis — 1Srs Air Bag - Occupant Classification System — 1Srs Air Bag Control System - Precautions — 1Srs Air Bag Control System - System — 1Srs Air Bag Control System - Diagnosis Sensor Unit — 1Srs Air Bag Control System - Inspection and Adjustment — 1Ventilation, Heater & Air Conditioner :: Ventilation System — 6Heater & Air Conditioning System - Precautions — 1Heater & Air Conditioning System - Preparation — 1Heater & Air Conditioning System - Component Parts — 1Heater & Air Conditioning System - Diagnosis and Repair Work Flow — 1Heater & Air Conditioning System - Compressor — 1Heater & Air Conditioning System - Cooler Pipe and Hose — 1Heater & Air Conditioning System - Condenser. Condenser — 1Heater & Air Conditioning System - Heating and Cooling Unit Assembly — 1Heater & Air Conditioning System - Service Data and Specifications (SDS) — 1Heater & Air Conditioning Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1Heater & Air Conditioning Control System - Ecu Diagnosis Information — 1Heater & Air Conditioning Control System - Basic Inspection — 1Heater & Air Conditioning Control System - Dtc/circuit Diagnosis — 1Heater & Air Conditioning Control System - Symptom Diagnosis — 1Heater & Air Conditioning Control System - Removal and Installation — 1Body Interior :: Interior — 8Instrument Panel - Precautions. Preparation. Clip List — 1Instrument Panel - Squeak and Rattle Trouble Diagnoses — 1Instrument Panel - Cluster Lid C — 1Seat - Precautions — 1Seat - Preparation. Clip List — 1Seat - Component Parts — 1Seat - System — 1Seat - Diagnosis and Repair Work Flow — 1Seat - Front Seat — 1Seat - Second Row Seats — 1Seat - Third Row Seats — 1Seat - Front Seat — 1Seat - Second Row Seat — 1Seat - Third Row Seat — 1Automatic Drive Positioner - Precautions. Preparation — 1Automatic Drive Positioner - System — 1Automatic Drive Positioner - Diagnosis and Repair Work Flow — 1Automatic Drive Positioner - Inspection and Adjustment — 1Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock — 38Security Control System - Precautions — 1Security Control System - System — 1Security Control System - Ecm, Bcm, Intelligent Key Unit, Ipdm E/r — 1Security Control System - Vehicle Security System Cannot Be Set — 1Glass & Window System - Precautions. Preparation — 1Glass & Window System - Squeak and Rattle Trouble Diagnoses — 1Power Window Control System - Precautions. Preparation — 1Power Window Control System - Power Supply and Ground Circuit — 1Power Window Control System - Power Window Motor Circuit — 1Power Window Control System - Front Power Window Rh Alone Does Not Operate — 1Power Window Control System - Rear Lh Side Power Window Alone Does Not Operate — 1Power Window Control System - Rear Rh Side Power Window Alone Does Not Operate — 1Roof - Precautions. Preparation — 1Roof - Power Supply and Ground Circuit — 1Roof - Moonroof Switch Assembly — 1Roof - Lin Communication Circuit — 1Roof - Auto Operation Does Not Operate — 1Roof - Anti-Pinch Function Does Not Operate — 1Exterior - Precautions. Preparation. Clip List (Preparation) — 1Exterior - Squeak and Rattle Trouble Diagnoses — 1Exterior - Fender Protector — 1Exterior - Over Fender — 1Exterior - Under Cover — 1Exterior - Roof Side Rail — 1Body Repair - Service Information — 1Service Information - Sheet Metal Work ++ — 1Service Information - Body Welding and Precautions ++ — 1Service Information - Safety and Health ++ — 1Service Information - Repairing Procedures and Precautions ++ — 1Body Repair - Precaution — 1Body Repair - Preparation — 1Body Repair - Removal and Installation — 1Driver Controls :: Mirrors — 8Exterior Lighting System - System Description — 1System Description - Component Parts ++ — 1Exterior Lighting System - Basic Inspection — 1Exterior Lighting System - Dtc/circuit Diagnosis — 1Exterior Lighting System - Symptom Diagnosis — 1Exterior Lighting System - Periodic Maintenance — 1Exterior Lighting System - Removal and Installation — 1Interior Lighting System - Precautions. Preparation — 1Interior Lighting System - Component Parts. Interior Lighting System — 1Interior Lighting System - System — 1Interior Lighting System - Diagnosis and Repair Work Flow — 1Interior Lighting System - Interior Lighting System Symptoms (Symptom Diagnosis). Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Interior Lighting System - Foot Lamp — 1Wiper & Washer - Precautions — 1Wiper & Washer - Preparation. Bcm, Ipdm E/r (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Wiper & Washer - System — 1Wiper & Washer - Diagnosis and Repair Work Flow — 1Defogger - Precautions. Bcm, A/c Auto Amp. (Ecu Diagnosis Information) — 1Defogger - Diagnosis and Repair Work Flow — 1Horn - Precautions — 1Electrical & Power Control :: Power Outlet — 13Body Control System - Precautions. Preparation — 1Body Control System - Component Parts — 1Body Control System - System — 1Body Control System - Diagnosis System (bcm) — 1Body Control System - Bcm — 1Lan System - System Description — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - Removal and Installation — 1Charging System - Precautions. Preparation. Ecm, Ipdm E/r (Ecu Diagnosis Information) — 1Charging System - Diagnosis and Repair Work Flow — 1Charging System - Charging System (Symptom Diagnosis). Generator (Removal and Installation). Service Data and Specifications (SDS) — 1Power Supply, Ground & Circuit Elements - Precautions. Preparation. Service Data and Specifications (SDS) — 1Driver Information & Multimedia :: Meter, Warning Lamp & Indicator — 25Warning Chime System - Application Notice (How to Use This Manual). Precautions — 1Warning Chime System - System — 1Warning Chime System - Diagnosis System (combination Meter) — 1Warning Chime System - Bcm, Combination Meter (Ecu Diagnosis Information). Diagnosis and Repair Work Flow (Basic Inspection) — 1Sonar System - Precautions. Preparation — 1Sonar System - Sonar Control Unit — 1Dtc/circuit Diagnosis - B2720 Corner Sensor [rl] ++ — 1Audio, Visual & Navigation System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Multi Av (av Control Unit) ++ — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Symptom Diagnosis - Multi Av System ++ — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Cruise Control & Driver Assistance :: Cruise Control System — 17Driver Assistance System - System Description — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Driver Assistance System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1System Description - Handling Precaution ++ — 1Driver Assistance System - Ecu Diagnosis Information — 1Driver Assistance System - Basic Inspection — 1Basic Inspection - Distance Sensor Alignment ++ — 1Basic Inspection - Camera Aiming Adjustment ++ — 1Basic Inspection - Action Test ++ — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Laser/radar (distance Sensor) ++ — 1Dtc/circuit Diagnosis - Lane Camera (front Camera Unit) ++ — 1Driver Assistance System - Symptom Diagnosis — 1Driver Assistance System - Removal and Installation — 1Driver Assistance System - System Description — 1System Description - System ++ — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Drive Mode System - Precautions — 1Drive Mode System - Component Parts. Drive Mode System — 1Drive Mode System - System — 1Drive Mode System - Diagnosis and Repair Work Flow — 1Drive Mode System - Drive Mode Select Switch Circuit — 1Maintenance - Precautions. Preparation — 1Maintenance - General Maintenance — 1Maintenance - Periodic Maintenance — 1Maintenance - Recommended Fluids and Lubricants — 1Maintenance - Engine Maintenance — 1Maintenance - Chassis and Body Maintenance — 1Engine Lubrication System - Periodic Maintenance — 1Engine Lubrication System - Removal and Installation — 1Engine Cooling System - System Description — 1Engine Cooling System - Removal and Installation — 1Engine Control System - Vq35dd — 1Fuel System - Removal and Installation — 1Starting System - System Description — 1Starting System - Dtc/circuit Diagnosis — 1Driveline - Transfer: Ty92b — 1Driveline - Rear Propeller Shaft: 3fcj-Cvj — 1Driveline - Rear Final Drive: R145 — 1Front Axle - Periodic Maintenance — 1Front Axle - Removal and Installation — 1Rear Axle - Periodic Maintenance — 1Rear Axle - Removal and Installation — 1Rear Suspension - Removal and Installation — 1Road Wheels & Tires - System Description — 1Road Wheels & Tires - Basic Inspection — 1Road Wheels & Tires - Dtc/circuit Diagnosis — 1Road Wheels & Tires - Symptom Diagnosis — 1Road Wheels & Tires - Periodic Maintenance — 1Road Wheels & Tires - Removal and Installation — 1Parking Brake System - System Description — 1Parking Brake System - Basic Inspection — 1Parking Brake System - Dtc/circuit Diagnosis — 1Parking Brake System - Symptom Diagnosis — 1Parking Brake System - Removal and Installation — 1Brake Control System - Vdc/tcs/abs — 1Brake Control System - Automatic Brake Hold — 1Brake Control System - Automatic Emergency Braking — 1Brake Control System - Rear Automatic Braking — 1Steering Control System - System Description — 1Steering Control System - Basic Inspection — 1Steering Control System - Dtc/circuit Diagnosis — 1Steering Control System - Symptom Diagnosis — 1Srs Air Bag - Removal and Installation — 1Srs Air Bag Control System - System Description — 1Srs Air Bag Control System - Basic Inspection — 1Srs Air Bag Control System - Symptom Diagnosis — 1Heater & Air Conditioning System - Symptom Diagnosis — 1Heater & Air Conditioning System - Periodic Maintenance — 1Heater & Air Conditioning Control System - Automatic Air Conditioning — 1Instrument Panel - Removal and Installation — 1Instrument Panel - Unit Disassembly and Assembly — 1Seat - Ecu Diagnosis Information — 1Seat - Dtc/circuit Diagnosis — 1Seat - Symptom Diagnosis — 1Automatic Drive Positioner - System Description — 1Automatic Drive Positioner - Ecu Diagnosis Information — 1Automatic Drive Positioner - Dtc/circuit Diagnosis — 1Automatic Drive Positioner - Symptom Diagnosis — 1Automatic Drive Positioner - Removal and Installation — 1Security Control System - System Description — 1Security Control System - Basic Inspection — 1Security Control System - Dtc/circuit Diagnosis — 1Security Control System - Symptom Diagnosis — 1Security Control System - Removal and Installation — 1Glass & Window System - Removal and Installation — 1Power Window Control System - System Description — 1Power Window Control System - Ecu Diagnosis Information — 1Power Window Control System - Basic Inspection — 1Power Window Control System - Dtc/circuit Diagnosis — 1Power Window Control System - Symptom Diagnosis — 1Power Window Control System - Removal and Installation — 1Roof - System Description — 1Roof - Ecu Diagnosis Information — 1Roof - Basic Inspection — 1Roof - Dtc/circuit Diagnosis — 1Roof - Symptom Diagnosis — 1Roof - Removal and Installation — 1Exterior - System Description — 1Exterior - Removal and Installation — 1Body Repair - Repair Information — 1Exterior Lighting System - Led Headlamp — 1Interior Lighting System - Dtc/circuit Diagnosis — 1Interior Lighting System - Removal and Installation — 1Wiper & Washer - System Description — 1Wiper & Washer - Dtc/circuit Diagnosis — 1Wiper & Washer - Symptom Diagnosis — 1Wiper & Washer - Removal and Installation — 1Defogger - System Description — 1Defogger - Dtc/circuit Diagnosis — 1Defogger - Symptom Diagnosis — 1Defogger - Removal and Installation — 1Horn - Removal and Installation — 1Body Control System - Basic Inspection — 1Body Control System - Dtc/circuit Diagnosis — 1Body Control System - Symptom Diagnosis — 1Body Control System - Removal and Installation — 1Lan System - Can Fundamental — 1Lan System - Can — 1Lan System - Can Gateway — 1Power Control System - Ipdm E/r — 1Power Control System - Power Distribution System — 1Charging System - System Description — 1Charging System - Dtc/circuit Diagnosis — 1Power Supply, Ground & Circuit Elements - System Description — 1Power Supply, Ground & Circuit Elements - Basic Inspection — 1Power Supply, Ground & Circuit Elements - Removal and Installation — 1Warning Chime System - System Description — 1Warning Chime System - Dtc/circuit Diagnosis — 1Warning Chime System - Symptom Diagnosis — 1Sonar System - System Description — 1Sonar System - Basic Inspection — 1Sonar System - Dtc/circuit Diagnosis — 1Sonar System - Symptom Diagnosis — 1Sonar System - Removal and Installation — 1Audio, Visual & Navigation System - Nissanconnect — 1Audio, Visual & Navigation System - Intelligent Around View Monitor System — 1Audio, Visual & Navigation System - Rear View Monitor System — 1Audio, Visual & Navigation System - Telematics System — 1Driver Assistance System - Adas Control Unit 2 — 1Driver Assistance System - Driver Assistance System — 1Driver Assistance System - Chassis Control — 1Drive Mode System - Removal and Installation — 1Dtc/circuit Diagnosis (C053c Wheel Speed Sensor ... U2141 Can Comm Circuit) — 1Dtc/circuit Diagnosis (P0011 Intake Valve Timing Control ... P0111 Iat Sensor) — 1Dtc/circuit Diagnosis (P0116 Engine Coolant Temperature Sensor ... P025b Fuel Pump Module a) — 1Dtc/circuit Diagnosis (P026b Injection Timing ... P0420 Three Way Catalyst Function) — 1Dtc/circuit Diagnosis (P0441 Evap Control System ... P0524 Engine Oil Pressure) — 1Dtc/circuit Diagnosis (P0532 A/c Refrigerant Pressure Sensor ... P064d Ecm) — 1Dtc/circuit Diagnosis (P06da Engine Oil Pressure Control Solenoid Valve ... P1217 Engine Over Temperature) — 1Dtc/circuit Diagnosis (P1220 Fuel Pump Control Module (fpcm) ... P1574 Ascd Vehicle Speed Sensor) — 1Dtc/circuit Diagnosis (P1575 Brake Switch ... P2101 Electric Throttle Control Function) — 1Dtc/circuit Diagnosis (P2118 Throttle Control Motor ... P34ac Electric Intake Valve Timing Control Actuator) — 1Dtc/circuit Diagnosis (Active Grille Shutter ... High Pressure Fuel Pump) — 1Dtc/circuit Diagnosis (Ignition Signal ... Variable Induction Air System) — 14012 C1040 Emergency Brake — 14013 C106a Wheel Sensor — 14014 C1078-55 Not Configuration — 14015 C10b4-98 Overheat — 14016 B1001 Lap Pre-Tensioner Lh — 14017 B0001 Driver Air Bag Module — 14018 B100e Knee Air Bag Module Rh — 14019 B142x Collision Detection — 1Dtc/circuit Diagnosis (B20c7-11 A/c Clutch ... B24a6-11 in-Vehicle Sensor) — 1Dtc/circuit Diagnosis (B24a6-15 in-Vehicle Sensor ... U2140-87 Can Comm Err (ecm)) — 1Dtc/circuit Diagnosis (C1f00-1c Control Unit ... C1f04-61 Brake Sw/stop Lamp Sw) — 1Dtc/circuit Diagnosis (C1f05-49 Front Camera Unit ... C1f70-87 Ethernet Circuit) — 1
~51min read

Engine Control System

System Description

SYSTEM DIAGRAM

SYSTEM DESCRIPTION

ECM controls the engine by various functions.

FunctionReference
Direct injection gasoline system System Description
Electric ignition system System Description
Fuel pressure control System Description
Fuel pump control module (FPCM) System Description
Intake valve timing control System Description
Exhaust valve timing control System Description
Air conditioning cut system System Description
Engine oil pressure control system System Description
Engine protection control at low engine oil pressure System Description
Cooling fan control System Description
Electronic controlled engine mount System Description
Evaporative emission system System Description
Throttle control System Description
Variable induction air system System Description
Automatic speed control device (ASCD) System Description
Oil control system System Description
Stop/start system System Description
CAN communication System Description

Fail safe

Description

When a DTC is detected, ECM executes a mode (in the Fail-safe mode) applicable to the DTC. The fail-safe mode has the preset traveling control mode (accelerator angle variation and engine output limit) and device fix mode.

Fail safe modeNissan Pathfinder Vehicle behaviorFail safe pattern
Traveling control mode Accelerator angle variation control

ECM controls the accelerator pedal depression speed to make it slower than actual speed. This causes a drop in accelerating performance and encourages the driver to repair malfunction.

A
Engine output control

ECM reduces the engine output, according to the rise in engine speed. This reduces the Nissan Pathfinder vehicle speed to encourage the driver to repair malfunction.

  • Driving at 70 km/h or more is possible.

B

ECM reduces the engine output, according to the rise in engine speed. This reduces the Nissan Pathfinder vehicle speed to encourage the driver to repair malfunction.

  • Driving at 40 km/h or more is possible.

C
Device fix mode
  • Fixes electric intake valve timing control motor in the reference position.

  • Fixes exhaust valve timing control solenoid valve in the reference position.

D
Combustion control mode Stratified charge combustion control at starting No stratified charge combustion at starting (cold start). E
Idle speed control Stops feedback control of idle speed and controls with specified speed. F
Recovery speed control at decelerating Stops recovery speed control by the fuel cut at decelerating and controls with specified speed.
Idle neutral control Stops idle neutral control.
Ignition timing correction control Partially controls ignition timing control. G
Retardation control Controls ignition timing delay control in the intermediate water temperature range.
Electric throttle control cancel mode ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed opening (approx. 5 degrees) by the return spring. H

Fail Safe List

DTC No.Detected itemsNissan Pathfinder Vehicle behavior
PatternOthers
ABCDEFGH
C053C 00 Nissan Pathfinder Vehicle speed sensor × — — — × — — — —

P0010

P0020
00 Electric intake valve timing control module — — — × × × — — —

P0011

P0012

P0021

P0022
00 Intake valve timing control — — — × — — — — —

P0014

P0015

P0019

P0024

P0025
00 Exhaust valve timing control — — — × — — — — —
P0017 00 Exhaust valve timing control — — — × — — — — —

P0078

P0084
00 Exhaust valve timing control solenoid valve — — — × — — — — —

P0087

P0088

P0090
00 Fuel rail pressure control × — — × × — — — —

P0101

P0102

P0103
00 Mass air flow sensor × × — × × × × — —

P0107

P0108
00 Barometric pressure sensor × × — × — — — — —

P0117

P0118
00 Engine coolant temperature sensor — — — — × × — — —

P0122

P0123

P0222

P0223

P2135
00 Throttle position sensor — — — × — — — — —

P0171

P0172

P0174

P0175
00 Fuel injection system × — — — × × — — —
P0190 00 Fuel rail pressure sensor × — — × × × — — —

P0191

P0192

P0193
00 × — — — × — — — —

P0201

P0202

P0203

P0204

P0205

P0206
00 Fuel injector × — — × × — — — —

P0300

P0301

P0302

P0303

P0304

P0305

P0306
00 Misfire × — — — × × — — —
P0335 00 Crankshaft position sensor — — — × × × — — —

P0340

P0345
00 Intake camshaft position sensor — — — × × × — — —

P0365

P0390
00 Exhaust camshaft position sensor — — — × — — — — —
P0500 00 Nissan Pathfinder Vehicle speed sensor × — — — × × — — —
P050A 00 Cold start control × — — — × — — —

P0604

P0605

P0606

P060B

P061B
00 ECM — — — × — — — × —
P0607 00 × × — — — — — — ASCD operation may be deactivated.
P060A 00 × × — × — — — × ASCD operation may be deactivated.

P062B

P062D

P062E
00 × — — × × — — — —

P06DD

P06DE
00 Engine oil pressure control — — — — — — — — Fixes engine oil pressure control valve in the high pressure control position.
P0641 00 Sensor power supply — — — × × × — — —
P0643 00 — — — × — — — × —
P1197 00 Out of gas — — — × — — — — —

P119A

P119B

P119C
00 Fuel pressure sensor × — — — × — — — —

P2100

P2103
00 Throttle control motor relay — — — × — — — × —
P2101 00 Electric throttle control — — — × — — — × —
P2118 00 Throttle control motor — — — × — — — × —
P2119 00 Electric throttle control actuator × × — × — — — × —

P2122

P2123

P2127

P2128

P2138
00 Accelerator pedal position sensor — — — × — — — — —

P23E9

P23EA

P2614

P2615
00 Intake camshaft position sensor (electric intake valve timing control signal) — — — × × × — — —

P23EB

P2616
00 — — — × × — — — —

P2617

P2618
00 Crankshaft position sensor (electric intake valve timing control signal) — — — × × — — — —
P2619 00 — — — × × × — — —
P25DF 00 Electric intake valve timing control actuator — — — × × — — — —
P25E8 00

ECM stops the electric valve timing control.

(The camshaft returns to the position of most retard angle.)

P34AC

P34AD

P34B1

P34C4

P34C5
00 —
P34B3 00 Electric intake valve timing control position sensor — — — × × — — — —
P34C8 00 Electric intake valve timing control module — — — × × × — — —
U0122 00 CAN communication line × — — — × — — — —

U012E

U042F
00 Engine communication — — — × × × — — —

STOP/START SYSTEM

When ECM detects error, ECM detects DTC, prohibits the start/stop system operation, and display the Stop/Start warning indicator. When ECM detects error while operating the stop/start system, ECM restarts the engine.

Auto Engine Shutoff System

System Description

SYSTEM DIAGRAM

Auto engine shutoff system is a function which is designed to automatically stop the engine after certain while to prevent an extended periods idling.

While idling and system operation condition meets, auto engine shutoff system start operate and timer in the system starts.

When any of the condition is deviate from operation condition, the timer will be reset.

The system display the countdown on the information display from 30 seconds before engine automatically stop.

Auto engine shutoff system can be canceled by steering switch operation even if the countdown announce is displayed.

However, after cancelling the system, when the ignition switch is turned ON again, the system will reset to the operating condition.

OPERATING CONDITION
Meets all of 6 conditions Acceleratorr pedal is not pressed
Brake pedal is not depressed
Nissan Pathfinder Vehicle is stopped
Engine running
Ignition switch ON
Meets either of 2 conditions (For A/T models) Shift position is in P range
(For M/T models) Meets all of 2 conditions Shift position is in Neutral position
Parking brake is in operation

AUTO ENGINE SHUTOFF SYSTEM DISPLAY STATUS (INFORMATION DISPLAY)

Refer to Indicator/Information.

BASIC OPERATION

Direct Injection Gasoline System

System Description

SYSTEM DIAGRAM

Component partsFunction
Crankshaft position sensor 1 Crankshaft Position Sensor 1
Exhaust camshaft position sensor Exhaust Camshaft Position Sensor

Mass air flow sensor

(With intake air temperature sensor)
Mass Air Flow Sensor (With Intake Air Temperature Sensor)
Intake air temperature sensor Mass Air Flow Sensor (With Intake Air Temperature Sensor)
Engine coolant temperature sensor Engine Coolant Temperature Sensor
Air fuel ratio (A/F) sensor 1 Air Fuel Ratio (A/F) Sensor 1
Fuel rail pressure sensor Fuel Rail Pressure Sensor
Throttle position sensor Electric Throttle Control Actuator
Accelerator pedal position sensor Accelerator Pedal Position Sensor
Battery ECM receives the battery voltage signal.
Knock sensor Knock Sensor
Heated oxygen sensor 2 Heated Oxygen Sensor 2
TCM ECM receives the shift position signal via CAN communication.
Power steering control module ECM receives the EPS operation signal via CAN communication.
ABS actuator and electric unit (control unit)

ECM receives the following signals via CAN communication.

  • VDC operation signal

  • TCS operation signal

A/C auto amp. ECM receives the A/C ON signal via CAN communication.
Combination meter ECM receives the Nissan Pathfinder vehicle speed signal via CAN communication.
ECM ECM (With Barometric Pressure Sensor)
Fuel injector Fuel Injector

SYSTEM DESCRIPTION

The adoption of the fuel injection method enables more accurate adjustment of fuel injection quantity by injecting atomized high-pressure fuel directly into the cylinder. This method allows high-powered engine, low fuel consumption, and emissions-reduction.

The amount of fuel injected from the fuel injector is determined by the ECM. The ECM controls the length of time the valve remains open (injection pulse duration). The amount of fuel injected is a program value in the ECM memory. The program value is preset by engine operating conditions. These conditions are determined by input signals (for engine speed, intake air, fuel rail pressure and boost pressure) from the crankshaft position sensor 1, exhaust camshaft position sensor, mass air flow sensor and fuel rail pressure sensor.

VARIOUS FUEL INJECTION INCREASE/DECREASE COMPENSATION

In addition, the amount of fuel injected is compensated to improve engine performance under various operating conditions as listed below.

<Fuel increase>

  • During warm-up

  • When starting the engine

  • During acceleration

  • Hot-engine operation

  • When selector lever position is changed from N to D

  • High-load, high-speed operation

<Fuel decrease>

  • During deceleration

  • During high engine speed operation

FUEL INJECTION CONTROL

Catalyst-heating Combustion

Catalyst-heating combustion is a combustion method.

Right after a start with the engine coolant temperature between −12 °C to 40 °C, the catalyst warm-up is accelerated by this combustion.

Homogeneous Combustion

Homogeneous combustion is a combustion method that fuel is injected during intake process so that combustion occurs in the entire combustion chamber, as is common with conventional methods.

As for a start except for starts with the engine cold, homogeneous combustion occurs.

MIXTURE RATIO FEEDBACK CONTROL (CLOSED LOOP CONTROL)

The mixture ratio feedback system provides the best air-fuel mixture ratio for driveability and emission control. The three way catalyst (manifold) can better reduce CO, HC and NOx emissions. This system uses A/F sensor 1 in the exhaust manifold to monitor whether the engine operation is rich or lean. The ECM adjusts the injection pulse width according to the sensor voltage signal. For more information about A/F sensor 1, refer to Air Fuel Ratio (A/F) Sensor 1. This maintains the mixture ratio within the range of stoichiometric (ideal air-fuel mixture).

This stage is referred to as the closed loop control condition.

Heated oxygen sensor 2 senses an oxygen concentration of exhaust gas at downstream of catalytic converter. Even if the switching characteristics of A/F sensor 1 shift, the air-fuel ratio is controlled to stoichiometric by the signal from heated oxygen sensor 2.

  • Open Loop Control

    The open loop system condition refers to when the ECM detects any of the following conditions. Feedback control stops in order to maintain stabilized fuel combustion.

    • Deceleration and acceleration

    • High-load, high-speed operation

    • Malfunction of A/F sensor 1 or its circuit

    • Insufficient activation of A/F sensor 1 at low engine coolant temperature

    • High engine coolant temperature

    • During warm-up

    • When starting the engine

MIXTURE RATIO SELF-LEARNING CONTROL

The mixture ratio feedback control system monitors the mixture ratio signal transmitted from A/F sensor 1. This feedback signal is then sent to the ECM. The ECM controls the basic mixture ratio as close to the theoretical mixture ratio as possible. However, the basic mixture ratio is not necessarily controlled as originally designed. Both manufacturing differences (i.e., mass air flow sensor sensing element) and characteristic changes during operation (i.e., fuel injector clogging) directly affect mixture ratio.

Accordingly, the difference between the basic and theoretical mixture ratios is monitored in this system. This is then computed in terms of “injection pulse duration” to automatically compensate for the difference between the two ratios.

“Fuel trim” refers to the feedback compensation value compared against the basic injection duration. Fuel trim includes “short-term fuel trim” and “long-term fuel trim”.

“Short term fuel trim” is the short-term fuel compensation used to maintain the mixture ratio at its theoretical value. The signal from A/F sensor 1 indicates whether the mixture ratio is RICH or LEAN compared to the theoretical value. The signal then triggers a reduction in fuel volume if the mixture ratio is rich, and an increase in fuel volume if it is lean.

“Long-term fuel trim” is overall fuel compensation carried out over time to compensate for continual deviation of the “short-term fuel trim” from the central value. Continual deviation will occur due to individual engine differences, wear over time and changes in the usage environment.

FUEL INJECTION TIMING

Sequential Direct Injection Gasoline System

Fuel is injected into each cylinder during each engine cycle according to the ignition order.

FUEL SHUT-OFF

Fuel to each cylinder is shut-off during deceleration, operation of the engine at excessively high speed or operation of the Nissan Pathfinder vehicle at excessively high speed.

Electric Ignition System

System Description

SYSTEM DIAGRAM

Component partsFunction
Crankshaft position sensor 1 Crankshaft Position Sensor 1
Exhaust camshaft position sensor Exhaust Camshaft Position Sensor

Mass air flow sensor

(With intake air temperature sensor)
Mass Air Flow Sensor (With Intake Air Temperature Sensor)
Engine coolant temperature sensor Engine Coolant Temperature Sensor
Throttle position sensor Electric Throttle Control Actuator
Accelerator pedal position sensor Accelerator Pedal Position Sensor
Battery ECM receives the battery voltage signal.
Knock sensor Knock Sensor
Heated oxygen sensor 2 Heated Oxygen Sensor 2
TCM ECM receives the shift position signal via CAN communication.
Combination meter ECM receives the Nissan Pathfinder vehicle speed signal via CAN communication.
ECM ECM (With Barometric Pressure Sensor)

Ignition coil

(With power transistor)
Ignition Coil and Spark Plug

SYSTEM DESCRIPTION

Ignition order: 1 - 2 - 3 - 4 - 5 - 6

The ignition timing is controlled by the ECM to maintain the best air-fuel ratio for every running condition of the engine. The ignition timing data is stored in the ECM.

The ECM receives information such as the injection pulse width and exhaust camshaft position sensor signal. Computing this information, ignition signals are transmitted to the power transistor.

During the following conditions, the ignition timing is revised by the ECM according to the other data stored in the ECM.

  • At starting

  • During warm-up

  • At idle

  • At low battery voltage

  • During acceleration

The knock sensor retard system is designed only for emergencies. The basic ignition timing is programmed within the anti-knocking zone, if recommended fuel is used under dry conditions. The retard system does not operate under normal driving conditions. If engine knocking occurs, the knock sensor monitors the condition. The signal is transmitted to the ECM. The ECM retards the ignition timing to eliminate the knocking condition.

Ignition cylinder detection signals

Fuel Pressure Control

System Description

SYSTEM DIAGRAM

Component partsFunction
Crankshaft position sensor 1 Crankshaft Position Sensor 1
Exhaust camshaft position sensor Exhaust Camshaft Position Sensor
Fuel rail pressure sensor Fuel Rail Pressure Sensor
Engine coolant temperature sensor Engine Coolant Temperature Sensor
Throttle position sensor Electric Throttle Control Actuator
Accelerator pedal position sensor Accelerator Pedal Position Sensor
Battery ECM receives the battery voltage signal.
ECM ECM (With Barometric Pressure Sensor)
High pressure fuel pump High Pressure Fuel Pump
FPCM Fuel Pump Control Module
Low pressure fuel pump Low Pressure Fuel Pump

SYSTEM DESCRIPTION

LOW FUEL PRESSURE CONTROL

  • The low fuel pressure pump is controlled by ECM. The pumped fuel passes through the fuel filter and is sent to the high pressure fuel pump.

  • Low fuel pressure is adjusted by the fuel pressure regulator.

HIGH FUEL PRESSURE CONTROL

The high pressure fuel pump raises the pressure of the fuel sent from the low pressure fuel pump. Actuated by the exhaust camshaft, the high pressure fuel pump activates the high pressure fuel pump solenoid based on a signal received from ECM, and adjusts the amount of discharge by changing the timing of closing the inlet check valve to control fuel rail pressure.

Fuel Pump Control Module (fpcm)

System Description

SYSTEM DIAGRAM

Component partsFunction
Crankshaft position sensor 1 Crankshaft Position Sensor 1
Exhaust camshaft position sensor Exhaust Camshaft Position Sensor
Engine coolant temperature sensor Engine Coolant Temperature Sensor

Mass air flow sensor

(With intake air temperature sensor)
Mass Air Flow Sensor (With Intake Air Temperature Sensor)
Battery ECM receives the battery voltage signal.
ECM ECM (With Barometric Pressure Sensor)
FPCM Fuel Pump Control Module
Low pressure fuel pump Low Pressure Fuel Pump

SYSTEM DESCRIPTION

The fuel pump control module (FPCM) controls the discharging volume of the fuel pump by the FPCM control signals (Low/Mid/High) depending on driving conditions.

ConditionsAmount of fuel flowSupplied voltage (Approx.)
For 1 second after turning ignition switch ON Low/Mid 12.9 V
  • Engine cranking

  • Engine coolant temperature is below 10 °C

  • Engine is running under high load and high speed conditions

High 10.7 – 12.9 V
Except the above Low/Mid 8.1 – 12.9 V

Intake Valve Timing Control

System Description

SYSTEM DIAGRAM

Component partsFunction
Crankshaft position sensor 1 Crankshaft Position Sensor 1
Intake camshaft position sensor Intake Camshaft Position Sensor
Engine oil temperature sensor Engine Coolant Temperature Sensor
ECM ECM (With Barometric Pressure Sensor)
Electric intake valve timing control module Electric Intake Valve Timing Control Module
Electric intake valve timing control actuator Electric Intake Valve Timing Control Actuator

SYSTEM DESCRIPTION

This engine uses an electric VTC. The electric VTC responds faster than hydraulic VTC and allows operating under low engine speed condition. This improves the fuel economy, engine output, and exhaust performance.

This mechanism continuously controls the phase of camshaft by the electric intake valve timing (IVT) control actuator with the amount of intake valve operation held constant.

ECM transmits a crankshaft position signal and an intake camshaft position signal to the electric IVT control module and transmits target values of electric IVT control actuator via engine communication (CAN).

The electric IVT control module controls the electric IVT control actuator according to a signal from ECM and changes the opening and closing timing of intake valve. Furthermore, the electric IVT control actuator has a diagnostic function and transmits a DTC detection signal to ECM via engine communication when detecting a system error.

Status of electric intake valve timing control actuatorElectric intake valve timing control actuator activation
Advanced angle Electric IVT control motor rotates faster than camshaft. This allows the camshaft position (cam phase) against camshaft sprocket to move toward the advanced angle.
Maintained Electric IVT control motor and camshaft rotate at the same speed.
Retard angle Electric IVT control motor rotates slower than camshaft. This allows the camshaft position (cam phase) against camshaft sprocket to move toward the retard angle.

Exhaust Valve Timing Control

System Description

SYSTEM DIAGRAM

Component partsFunction
Crankshaft position sensor 1 Crankshaft Position Sensor 1
Exhaust camshaft position sensor Exhaust Camshaft Position Sensor
Engine oil temperature sensor Engine Oil Temperature Sensor
Combination meter ECM receives the Nissan Pathfinder vehicle speed signal via CAN communication.
ECM ECM (With Barometric Pressure Sensor)
Exhaust valve timing control solenoid valve Exhaust Valve Timing Control Solenoid Valve

SYSTEM DESCRIPTION

With the exhaust valve timing controller which controls the phase of exhaust camshaft to optional position continuously, ECM improves both low-middle speed torque and high speed performance, emission and fuel efficiency by optimizing the exhaust valve open/close timing according to driving conditions.

The exhaust valve timing controller is hydraulically controlled by the exhaust valve timing control solenoid valve.

This mechanism hydraulically controls cam phases continuously with the fixed operating angle of the exhaust valve.

The ECM receives signals such as crankshaft position, camshaft position, engine speed, and engine oil temperature. Then, the ECM sends ON/OFF pulse duty signals to the exhaust valve timing control solenoid valve depending on driving status. This makes it possible to control the shut/open timing of the exhaust valve to increase engine torque and output in a range of high engine speed.

EXHAUST VALVE TIMING CONTROL SOLENOID VALVE CONTROL

The exhaust valve timing control solenoid valve is driven ON-OFF (duty control) by ECM output signal, and controls the open/close timing of the exhaust valve to the optimum by changing its duty ratio according to the Nissan Pathfinder vehicle's driving condition.

Exhaust valve timing control solenoid valve conditionExhaust valve timing controller operation
Engine OFF When starting the engine, the controller vane and sprocket are fixed in full advanced position by the reaction force of return spring, improving the starting performance of the engine.
Active (Retard angle) When the energization rate to the control solenoid valve is increased, the oil pressure from the oil pump is conveyed to the retard angle chamber of the controller. And advanced angle chamber oil is drained. Accordingly, the controller vane rotates leftward and the phase of camshaft becomes retard angle. This condition brings about the greater overlap with the intake valve, enabling the exhaust gas cleaning by the internal EGR effect and the fuel consumption improvement by the reduction in pumping loss.
Neutral (Maintained) When it is the target valve timing, the energization rate to the control solenoid valve is adjusted to the intermediate state. The solenoid valve is positioned at the neutral position and the oil path is interrupted to maintain the cam shaft phase.
Return (Advanced angle) When the energization rate to the control solenoid valve is decreased, the oil pressure from the oil pump is conveyed to the advanced chamber of the controller. And retard angle chamber oil is drained. Accordingly, the controller vane rotates rightward and the phase of camshaft becomes advanced angle.

EXHAUST VALVE TIMING CONTROL FEEDBACK CONTROL

Cam Position Detection

The exhaust camshaft position sensor detects a cam position, by using the groove on the plate located at the rear of the exhaust camshaft.

Feedback Control

The exhaust camshaft position sensor feeds back an actual cam position signal to ECM. Based on the signal, ECM controls the exhaust valve timing control solenoid valve to satisfy the optimum target valve opening/closing timing according to a driving condition.

Air Conditioning Cut Control

System Description

SYSTEM DIAGRAM

Exhaust camshaft position sensor is not used for engine control operation.

Component partsFunction
Crankshaft position sensor 1 Crankshaft Position Sensor 1
Exhaust camshaft position sensor Exhaust Camshaft Position Sensor
Engine coolant temperature sensor Engine Coolant Temperature Sensor
Accelerator pedal position sensor Accelerator Pedal Position Sensor
Battery ECM receives the battery voltage signal.
Refrigerant pressure sensor Refrigerant Pressure Sensor
Heated oxygen sensor 2 Heated Oxygen Sensor 2
Power steering control module ECM receives the EPS operation signal via CAN communication.
Combination meter ECM receives the Nissan Pathfinder vehicle speed signal via CAN communication.
A/C auto amp. ECM receives the A/C ON signal via CAN communication.
ECM ECM (With Barometric Pressure Sensor)
IPDM E/R ECM transmits the air conditioner cut control signal via CAN communication.
Compressor A/C Compressor

SYSTEM DESCRIPTION

This system improves engine operation when the air conditioner is used.

Under the following conditions, the air conditioner is turned off.

  • When the accelerator pedal is fully depressed.

  • When cranking the engine.

  • At high engine speeds.

  • When the engine coolant temperature becomes excessively high.

  • When operating power steering during low engine speed or low Nissan Pathfinder vehicle speed.

  • When engine speed is excessively low.

  • When refrigerant pressure is excessively low or high.

Engine Oil Pressure Control System

System Description

SYSTEM DIAGRAM

Component partsFunction
Crankshaft position sensor 1 Crankshaft Position Sensor 1
Exhaust camshaft position sensor Exhaust Camshaft Position Sensor
Engine coolant temperature sensor Engine Coolant Temperature Sensor
Engine oil pressure sensor Engine Oil Pressure Sensor
Engine oil temperature sensor Engine Oil Temperature Sensor
Battery ECM receives the battery voltage signal.
ECM ECM (With Barometric Pressure Sensor)
Engine oil pressure control solenoid valve Engine Oil Pressure Control Solenoid Valve

SYSTEM DESCRIPTION

ECM performs the variable hydraulic control (low oil pressure control and high oil pressure control) based on signals from each sensor according to oil temperature and engine load. ECM activates the engine oil pressure control solenoid valve and switches to the low oil pressure control and high oil pressure control. ECM uses the low oil pressure control for 80-90% of the operating area to maintain low oil pressure and stops piston cooling jet (i.e. achievement of less than or equal to jet injection valve opening pressure).

High oil pressure control start condition

  • High oil pressure control start condition

  • High engine speed

  • Coolant temperature is 60 °C or more under high engine load condition

Low oil pressure control start condition

  • Coolant temperature is less than 60 °C under low engine speed condition

  • Coolant temperature is 60 °C or more under low engine load and low engine speed conditions

Engine Protection Control at Low Engine Oil Pressure

System Description

SYSTEM DIAGRAM

Component partsFunction
Engine oil pressure sensor Engine Oil Pressure Sensor
Crankshaft position sensor 1 Crankshaft Position Sensor 1
Engine oil temperature sensor Engine Oil Temperature Sensor
ECM ECM (With Barometric Pressure Sensor)
Combination meter It receives the engine oil pressure waning lamp signal from ECM via CAN communication.

SYSTEM DESCRIPTION

  • The engine protection control at low engine oil pressure warns the driver of a decrease in engine oil pressure by the oil pressure warning lamp before the engine becomes damaged.

  • When detecting a decrease in engine oil pressure at an engine speed less than 1,000 rpm, ECM transmits an oil pressure warning lamp signal to the combination meter. The combination meter turns ON the oil pressure warning lamp, according to the signal.

  • When detecting a decrease in engine oil pressure at an engine speed 1,000 rpm or more, ECM transmits an oil pressure warning lamp signal to the combination meter.

    The combination meter turns ON the oil pressure warning lamp, according to the signals. When detecting a decrease in engine oil pressure, ECM cuts fuel if the engine speed exceeds the specified value.

Decrease in engine oil pressureEngine speedCombination meterFuel cut
Oil pressure warning lamp
Detection Less than 1,000 rpm ON* NO
1,000 rpm or more ON YES

*: When detecting a normal engine oil pressure, ECM turns OFF the oil pressure warning lamp.

Cooling System

System Description

SYSTEM DIAGRAM

Component partsFunction
Crankshaft position sensor 1 Crankshaft Position Sensor 1
Exhaust camshaft position sensor Exhaust Camshaft Position Sensor
Engine coolant temperature sensor Engine Coolant Temperature Sensor
Refrigerant pressure sensor Refrigerant Pressure Sensor
Battery ECM receives the battery voltage signal.
Combination meter ECM receives the Nissan Pathfinder vehicle speed signal via CAN communication.
A/C auto amp.

ECM receives below signal via CAN communication.

  • A/C ON signal

  • A/C evaporator temperature signal

  • Target A/C evaporator temperature signal

  • Blower fan ON signal

ECM ECM (With Barometric Pressure Sensor)
IPDM E/R ECM transmits the cooling fan speed request signal via CAN communication.
Cooling fan control module Cooling Fan
Cooling fan motor

SYSTEM DESCRIPTION

ECM controls cooling fan speed corresponding to vehicle speed, engine coolant temperature, air conditioner ON signal, refrigerant pressure, target A/C evaporator temperature, and A/C evaporator temperature.

Cooling fan speed request signal is sent to IPDM E/R from ECM by CAN communication line. Then, IPDM E/R sends ON/OFF pulse duty signal to cooling fan control module. Corresponding to this ON/OFF pulse duty signal, cooling fan control module gives cooling fan motor operating voltage to cooling fan motors. Cooling fan speed is controlled by duty cycle of cooling fan motor operating voltage sent from cooling fan control module.

Electronic Controlled Engine Mount

System Description

SYSTEM DIAGRAM

Component partsFunction
Crankshaft position sensor 1 Crankshaft Position Sensor 1
Intake camshaft position sensor Intake Camshaft Position Sensor
Combination meter ECM receives the Nissan Pathfinder vehicle speed signal via CAN communication.
ECM ECM (With Barometric Pressure Sensor)
Engine mount control solenoid valve Electronic Controlled Engine Mount

SYSTEM DESCRIPTION

The ECM controls the engine mount operation corresponding to the engine speed. The control system has a 2-step control [Soft/Hard]

Vehicle conditionEngine mount control
Engine speed: Below 950 rpm Soft
Engine speed: Above 950 rpm Hard

ELECTRONIC CONTROLLED ENGINE MOUNT LINE DRAWING

Electronic controlled engine mount control solenoid valve Intake manifold collector
: From next figure
Front electronic controlled engine mount Rear electronic controlled engine mount
: To previous figure

Evaporative Emission System

System Description

SYSTEM DIAGRAM

Component partsFunction
Crankshaft position sensor 1 Crankshaft Position Sensor 1
Exhaust camshaft position sensor Exhaust Camshaft Position Sensor

Mass air flow sensor

(With intake air temperature sensor)
Mass Air Flow Sensor (With Intake Air Temperature Sensor)
Engine coolant temperature sensor Engine Coolant Temperature Sensor
Air fuel ratio (A/F) sensor 1 Air Fuel Ratio (A/F) Sensor 1
Throttle position sensor Electric Throttle Control Actuator
Accelerator pedal position sensor Accelerator Pedal Position Sensor
Battery ECM receives the battery voltage signal.
EVAP control system pressure sensor EVAP Control System Pressure Sensor
Combination meter ECM receives the Nissan Pathfinder vehicle speed signal via CAN communication.
ECM ECM (With Barometric Pressure Sensor)
EVAP canister purge volume control solenoid valve EVAP Canister Purge Volume Control Solenoid Valve

SYSTEM DESCRIPTION

The evaporative emission system is used to reduce hydrocarbons emitted into the atmosphere from the fuel system. This reduction of hydrocarbons is accomplished by activated charcoals in the EVAP canister.

The fuel vapor in the sealed fuel tank is led into the EVAP canister which contains activated carbon and the vapor is stored there when the engine is not operating or when refueling to the fuel tank.

The vapor in the EVAP canister is purged by the air through the purge line to the intake manifold when the engine is operating. EVAP canister purge volume control solenoid valve is controlled by ECM. When the engine operates, the flow rate of vapor controlled by EVAP canister purge volume control solenoid valve is proportionally regulated as the air flow increases.

EVAP canister purge volume control solenoid valve also shuts off the vapor purge line during decelerating and idling.

Throttle Control

System Description

SYSTEM DIAGRAM

Component partsFunction
Crankshaft position sensor 1 Crankshaft Position Sensor 1
Engine coolant temperature sensor Engine Coolant Temperature Sensor
Exhaust camshaft position sensor Exhaust Camshaft Position Sensor

Mass air flow sensor

(With intake air temperature sensor)
Mass Air Flow Sensor (With Intake Air Temperature Sensor)
Intake air temperature sensor Mass Air Flow Sensor (With Intake Air Temperature Sensor)
Accelerator pedal position sensor Accelerator Pedal Position Sensor
Ignition switch ECM receives the ignition start signal and OFF signal.
Combination meter ECM receives the Nissan Pathfinder vehicle speed signal via CAN communication.
A/C auto amp.

ECM receives below signal via CAN communication.

  • A/C ON signal

  • Blower fan ON signal

ECM ECM (With Barometric Pressure Sensor)
Electric throttle control actuator Electric Throttle Control Actuator

SYSTEM DESCRIPTION

ECM calculates the value of signal transmitted from the accelerator pedal and activates the throttle valve by transmitting a control signal to the electric throttle control actuator. This allows the optimum throttle angle and improves drivability and fuel consumption. In addition, ECM learns the fully closed position every time when the ignition switch is turned OFF to improve the accuracy in throttle valve position.

When a malfunction occurs in the throttle control system, the throttle valve is closed by the return spring and maintains the minimum engine speed by holding a slightly opened condition which is close to the fully opened condition. This allows the securing of brake system, power steering system, and electric system and the ensuring of the safety.

Variable Induction Air System

System Description

SYSTEM DIAGRAM

Component partsFunction
Crankshaft position sensor 1 Crankshaft Position Sensor 1
Intake camshaft position sensor Intake Camshaft Position Sensor

Mass air flow sensor

(With intake air temperature sensor)
Mass Air Flow Sensor (With Intake Air Temperature Sensor)
Engine coolant temperature sensor Engine Coolant Temperature Sensor
Throttle position sensor Electric Throttle Control Actuator
Accelerator pedal position sensor Accelerator Pedal Position Sensor
Battery ECM receives the battery voltage signal.
ECM ECM (With Barometric Pressure Sensor)
VIAS control solenoid valve 1 and 2 VIAS Control Solenoid Valve 1 and 2

SYSTEM DESCRIPTION

In the medium speed range, the ECM sends the ON signal to the VIAS control solenoid valve. This signal introduces the intake manifold vacuum into the power valve actuator and therefore closes the power valve. Under this condition, the pressure waves of the exhaust stroke do not disturb the pressure waves of the intake stroke of each opposite bank. Therefore, charging efficiency is increased together with the effect of the long intake passage.

However, in the high speed range, the ECM sends the OFF signal to the VIAS control solenoid valve and the power valve is opened. Under this condition, the pressure waves of intake stroke are resonant with those of each opposite bank exhaust stroke. Therefore, charging efficiency is also increased.

In addition, both valves 1 and 2 are opened or closed in other ranges mentioned above. Thus maximum charging efficiency is obtained for the various driving conditions.

VACUUM HOSE DRAWING

Power valve actuator 1 VIAS control solenoid valve 1 VIAS control solenoid valve 2
Power valve actuator 2 Intake manifold collector

Automatic Speed Control Device (ascd)

System Description

SYSTEM DIAGRAM

Component partsFunction
Brake pedal position switch Stop Lamp Switch Brake Pedal Position Switch
ASCD steering switch ASCD Steering Switch
TCM

ECM receives the following signals via CAN communication.

  • Output shaft revolution signal

  • Shift position signal

Combination meter
  • ECM receives the Nissan Pathfinder vehicle speed signal via CAN communication.

  • ECM transmits ASCD status signal via CAN communication.

ECM ECM (With Barometric Pressure Sensor)
Electric throttle control actuator Electric Throttle Control Actuator

BASIC ASCD SYSTEM

Refer to Owner's Manual for ASCD operating instructions.

Automatic Speed Control Device (ASCD) allows a driver to keep vehicle at predetermined constant speed without depressing accelerator pedal. Driver can set Nissan Pathfinder vehicle speed in advance between approximately 40 km/h and 144 km/h.

ECM controls throttle angle of electric throttle control actuator to regulate engine speed.

Operation status of ASCD is indicated by CRUISE indicator and SET indicator in combination meter. If any malfunction occurs in the ASCD system, it automatically deactivates control.

SET OPERATION

Press MAIN switch. (The CRUISE indicator in combination meter illuminates.)

When vehicle speed reaches a desired speed between approximately 40 km/h and 144 km/h, press COAST/SET switch. (Then SET lamp in combination meter illuminates.)

ACCELERATE OPERATION

If the ACCEL/RES switch is pressed during cruise control driving, increase the vehicle speed until the switch is released or Nissan Pathfinder vehicle speed reaches maximum speed controlled by the system.

And then ASCD will maintain the new set speed.

CANCEL OPERATION

When any of following conditions exist, cruise operation will be canceled.

  • CANCEL switch is pressed

  • More than 2 switches at ASCD steering switch are pressed at the same time (Set speed will be cleared)

  • Brake pedal is depressed

  • Selector lever is in the N, P, R position

  • Nissan Pathfinder Vehicle speed decreased to 13 km/h lower than the set speed

  • TCS system is operated

When the ECM detects any of the following conditions, the ECM will cancel the cruise operation and inform the driver by blinking indicator lamp.

  • Engine coolant temperature is slightly higher than the normal operating temperature, CRUISE lamp may blink slowly.

    When the engine coolant temperature decreases to the normal operating temperature, CRUISE lamp will stop blinking and the cruise operation will be able to work by pressing COAST/SET switch or ACCEL/RES switch.

  • Malfunction for some self-diagnoses regarding ASCD control: SET indicator will blink quickly.

If MAIN switch is turned to OFF while ASCD is activated, all of ASCD operations will be canceled and Nissan Pathfinder vehicle speed memory will be erased.

COAST OPERATION

When the COAST/SET switch is pressed during cruise control driving, decrease vehicle set speed until the switch is released. And then ASCD will maintain the new set speed.

RESUME OPERATION

When the ACCEL/RES switch is pressed after cancel operation other than pressing MAIN switch is performed, Nissan Pathfinder vehicle speed will return to last set speed. To resume vehicle set speed, vehicle condition must meet following conditions.

  • Brake pedal is released

  • CVT shift selector lever is in the P and N positions

  • Nissan Pathfinder Vehicle speed is greater than 40 km/h and less than 144 km/h

Can Communication

System Description

CAN (Controller Area Network) is a serial communication line for real time application. It is an on-Nissan Pathfinder vehicle multiplex communication line with high data communication speed and excellent error detection ability. Many electronic control units are equipped onto a Nissan Pathfinder vehicle, and each control unit shares information and links with other control units during operation (not independent). In CAN communication, control units are connected with 2 communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring. Each control unit transmits/receives data but selectively reads required data only.

Refer to CAN Communication Control Circuit, about CAN communication for detail.

Oil Control System

System Description

SYSTEM DIAGRAM

Component partsFunction
Crankshaft position sensor 1 Crankshaft Position Sensor 1
Engine coolant temperature sensor Engine Coolant Temperature Sensor
Mass Air Flow Sensor (With Intake Air Temperature Sensor) Mass Air Flow Sensor (With Intake Air Temperature Sensor)
ECM ECM (With Barometric Pressure Sensor)
Combination meter
  • ECM receives the remeing distance reset request signal via CAN communication.

  • ECM transmits remeing distance signal via CAN communication.

SYSTEM DESCRIPTION

ECM calculates engine load, engine coolant temperature, and engine speed based on signals from the mass air flow sensor, engine coolant temperature sensor, and crankshaft position sensor 1 and monitors the deterioration state of engine oil.

When the mileage before engine oil change comes to approximately 1,500 km or less, pre-alert message is displayed to inform the driver that the maintenance timing is close as shown in the following table.

Remaining mileage to the engine oil change timingAlert timing
1,000 km < the mileage ≤ 1,500 km (630 mile <the mileage ≤ 940 mile) The first IGN ON after reaching 1,500 km (940 mile)
500 km < the mileage ≤ 1,000 km (310 mile < the mileage ≤ 630 mile) The first IGN ON after reaching 1,000 km (630 mile)
500 km or less (310 mile or less) The first IGN ON every 100 km (60 mile)

Furthermore, when the timing is passed, alert message is displayed every time when ignition switch is turned ON to inform the driver that engine oil change is necessary.

At oil change, the mileage must be reset using vehicle information display function.

Stop/start System

System Description

SYSTEM DIAGRAM

Electric oil pump is not applied.

INPUT/OUTPUT SIGNAL CHART

Input/OutputTransmits/Receives componentSignal nameDescription
Input Accelerator pedal position sensor Accelerator pedal position sensor signal Detects an accelerator pedal position.
Crankshaft position sensor Crankshaft position sensor signal Detects an engine speed.
Engine coolant temperature sensor Engine coolant temperature sensor signal Detects an engine coolant temperature.
Atmospheric pressure sensor Atmospheric pressure sensor signal Detects an atmospheric pressure.
IPDM E/R CAN communication Stop/Start permit signal Detects the Electric Energy management system is ready to operate the stop/start system.
Hood switch signal Detects engine hood status.
Starter status signal Detects the status of starter
Starter relay and starter control relay status signal Detects the status of Starter relay.
BCM CAN communication Stop lamp switch signal Detects the status of brake pedal switch.
Door switch signal Detects the status of driver side door.
Stop/Start OFF switch signal Detects stop/start OFF switch status.
I-key exist information signal Detects the i-key exist
Driver seatbelt switch malfunction signal Detects the driver seatbelt switch is malfunction.
Delivery mode signal Detects Nissan Pathfinder vehicle is in delivery mode
Seat belt buckle switch signal Detects driver is sitting on the driver seat.
ABS actuator and electric unit (control unit) CAN communication Nissan Pathfinder Vehicle speed signal Detects vehicle speed.
Brake fluid pressure sensor signal Detects brake fluid pressure.
ABS operation signal Detects ABS operation.
Stop/Start permit signal Detects the Braking system is ready to operate the stop/start system
ABS malfunction signal Detects ABS is malfunction
Brake booster pressure status signal Detects the status of brake booster pressure.
Stand Still Assist signal Detect the Stand still Assist status.
Road sloop estimetion signal Detects Nissan Pathfinder vehicle angularity.
EPS control unit CAN communication EPS torque signal Detects an operational state of EPS system.
A/C auto amp. CAN communication Stop/Start permit signal Detects the air conditioning system is ready to operate the stop/start system.
Combination meter CAN communication Parking brake status signal Detects the status of parking brake
TCM CAN communication Stop/Start permit signal Detects the transmission is ready to operate the stop/start system.
Shift position signal Detects the transmission is ready to operate the stop/start system.
Transmission malfunction signal Detects Transmission is malfunction.
Electric parking brake CAN communication Stop/Start permit signal Detects the electrical parking brake status.
ADAS control unit 2 CAN communication Stop/Start permit signal Detects the pro pilot status.
Chassis control module CAN communication Drive mode status signal Detects the drive mode status.
Output BCM CAN communication Stop/Start status signal Transmits a stop/start status signal
ST Cut relay ON request signal Transmits ST Cut relay ON request according to the stop/start system
Stop/start switch lamp ON request signal | Transmits the stop/start switch lamp ON request
ABS actuator and electric unit (control unit) CAN communication Stop/Start status signal Transmits a stop/start status signal
Brake hold request signal Transmits the brake hold/release request according to the stop/start system.
EPS control unit CAN communication Stop/Start status signal Transmits a stop/start status signal
A/C auto amp. CAN communication Stop/Start status signal Transmits a stop/start status signal
TCM CAN communication Stop/Start status signal Transmits a stop/start status signal
Combination meter CAN communication Stop/Start indicator lamp and message request signal Transmits request signal which turns ON the stop/start indicator lamp and display message
Electric parking brake CAN communication Stop/Start status signal Transmit a stop/start status signal.
ADAS control unit 2 CAN communication Stop/Start status signal Transmit a stop/start status signal.

SYSTEM DESCRIPTION

The stop/start system enables the engine to automatically stop/restart with a simple operation and reduces unnecessary idling during stoplight or traffic congestion to improve fuel economy, reduce exhaust gas, and minimize noise.

ECM detects a vehicle condition, engine condition and driver′s operation condition based on signals sent from each unit and the sensors to comprehensively control the stop/start system.

The operation condition of the stop/start system is indicated by the stop/start indicator lamp on the combination meter and showing on the information display. (Refer to Switch Name and Function.) If a malfunction is detected in the stop/start system, the system control is automatically deactivated and the malfunction is alerted to the driver by blinking the stop/start indicator lamp and showing the status on the information display. When a driver′s operation is judged as dangerous one during the stop/start system operation, the stop/start indicator lamp blinks at a high speed and the status is shown on the information display . The buzzer mounted on the combination meter sounds simultaneously to warn the driver of the dangerous operation.

Stop/start indicator lamp status

System conditionConditionStop/start indicator lampWarning chime
Operate Normal Illuminate —
Hood open No display Sound
Fail-Safe Starter motor operation counter: too much blinking —
Malfunction of stop/start system Blinking —

BASIC OPERATION

FUNCTION DESCRIPTION

When the stop/start system readiness conditions are satisfied while the vehicle is moving, the system is ready.

When the stop/start system operation conditions are satisfied while the vehicle is in a stop condition, the engine is stopped.

The amount of fuel saved by the stop/start system and CO2 saved information are indicated on the combination meter.

When the engine restart conditions are satisfied, ECM makes IPDM E/R restart the engine.

After restarting the engine, the stop/start indicator lamp and the indication on the information display turn OFF.

Stop/Start Readiness Condition

ECM judges stop/start system is ready when the following conditions are satisfied.

ItemCondition
Nissan Pathfinder Vehicle Stop/start OFF switch OFF (Switch indicator: OFF)
Stop/start indicator Lamp Not blink (No malfunction)
Door (driver side) Close
Seat belt (driver side) Fastened
Driving history Drive the Nissan Pathfinder vehicle at 13 km/h or more after start the engine with ignition switch

Drive the Nissan Pathfinder vehicle at 8 km/h or more after restart

Passes 5 seconds or more after restart
Hood Close
Air conditioning Automatic air conditioning Not in DEF mode
Receives Stop/start permit signal
Manual air conditioning Not in DEF mode
ABS System is normal
ABS not activated*2
Receives Stop/start permit signal
EPS System is normal
Battery status Receives Stop/start permit signal from IPDM E/R.
Gear Position D position
I-key I-key exists inside Nissan Pathfinder vehicle
ST RLY operation status Relay operates correctly
Starter motor No starter motor long continuous operation
Delivery mode Not in delivery mode*2
Brake booster pressure Presence of sufficient negative pressure to a brake force. (Refer to System Description.)
Stand Still Activation Receives Stop/Start permit signal.
Pro pilot Receives Stop/Start permit signal.
Intelligent Parking Assist Receives Stop/Start permit signal.
Drive mode switch Detects TOW mode.

*1: If ABS system is activated, drive the vehicle at 12 km/h or more after stop the vehicle.

*2: No activation in market

Stop/Start Operation Condition

When the following conditions are satisfied, ECM stops the engine. And the combination meter turns ON a stop/start indicator lamp.

ItemCondition
Nissan Pathfinder Vehicle Vehicle speed Vehicle stopped [0 km/h]
Steering wheel Not steer (steering force does not occur)
Brake pedal Depressed
Brake fluid pressure 0.6 Mpa (6 bar, 6.12 kg/cm2, 87 psi)
Nissan Pathfinder Vehicle angularity Approx. 14% or less
ST RLY Cut relay Close
Engine Engine speed Around idle speed (Approx. 1,200 rpm or less)
Elevation 2500 m (8,202 ft)
Engine coolant temperature 37 - 100℃ (98.6 - 212°F)
Engine system Permit Stop/start operation
Transmission Transmission system Receives Stop/start permit signal
Gear position D position.

Restart Condition

When any of the following conditions is satisfied during stop/start system operating condition, ECM restarts the engine. And the combination meter turns OFF the stop/start indicator lamp.

ItemCondition
Stop/Start before Nissan Pathfinder vehicle haltStop/Start
Nissan Pathfinder Vehicle Stop/start OFF switch ON (Switch indicator ON)
Door (driver side) Open
Seat belt Released
I-key I-key doesn't exist inside Nissan Pathfinder vehicle
Air conditioning Auto air conditioning Select DEF mode
Air conditioning system cannot keep the performance.
Manual air conditioning Select DEF mode and fan is ON
Brake Brake pedal Released
Brake pedal negative pressure Insufficient brake negative pressure
Accelerator pedal Depressed
Engine Engine coolant temperature less than 36℃ (96.8°F)、 over than 100℃ (212°F)
Engine system Inhibit Stop/start operation
Trans mission Shift lever position Except for D position
Paddle shift Operation
Battery

Poor battery performance

(for details, refer to System Description.)
ABS Receives Stop/start operation
Intelligent Parking Assist
Stand Still Assist
Traffic Jam Pilot
Emargency brake
Drive mode switch Selected the TOW mode

Engine stalled Condition

When any of the following conditions is satisfied during stop/start system operating condition, ECM stalls the engine.

ItemCondition
Nissan Pathfinder Vehicle Hood Open

Warning Lamps/indicator Lamps

Engine Oil Pressure Warning Lamp

DESIGN/PURPOSE

When engine oil pressure is low, the oil pressure warning lamp informs the driver of low oil pressure to prevent damage to the engine.

BULB CHECK

Not applicable

OPERATION AT COMBINATION METER CAN COMMUNICATION CUT-OFF OR UNUSUAL SIGNAL

For the operation for CAN communications blackout or abnormal signal reception, refer to Fail-Safe.

SYSTEM DIAGRAM

SIGNAL PATH

ECM calculates an engine oil pressure according to a signal transmitted from the engine oil pressure sensor. When the engine oil pressure is low, ECM transmits the engine oil pressure warning lamp signal to combination meter via CAN communication. Then the engine oil pressure warning lamp illuminates.

LIGHTING CONDITION

When any of the following conditions is satisfied:

  • Ignition switch: ON

  • Engine oil pressure is the specified value or more.

SHUTOFF CONDITION

When any of the following conditions is satisfied:

  • Ignition switch: OFF

  • Engine oil pressure is the specified value or more.

TIMING CHART

Malfunction Indicator Lamp (MIL)

DESIGN/PURPOSE

When a malfunction which increases exhaust gases is detected, ECM turns ON MIL and informs the driver of the necessity of inspection and repair.

When a malfunction which causes damage to the catalyst is detected, ECM immediately blinks MIL to alert the driver.

BULB CHECK

The bulb turns ON after turning ON the ignition switch (engine stop) and turns OFF after restarting the engine.

OPERATION AT COMBINATION METER CAN COMMUNICATION CUT-OFF OR UNUSUAL SIGNAL

For the operation for CAN communication blackout in the combination meter, refer to Fail-Safe.

SYSTEM DIAGRAM

SIGNAL PATH

  • When the lighting conditions of the malfunction indicator lamp (MIL) are satisfied, ECM transmits a malfunction indicator lamp (MIL) signal to the combination meter via CAN communication.

  • The combination meter turns ON or blinks the malfunction indicator lamp (MIL), according to a signal received from ECM.

LIGHTING CONDITION

When all of the following conditions are satisfied:

  • Ignition switch: ON

  • DTC which influences on exhaust gasses is judged.

For DTCs that the malfunction indicator lamp turns ON and the number of DTC diagnosis trips, refer to DTC Index.

SHUTOFF CONDITION

When any of the following conditions is satisfied:

  • Ignition switch: OFF

  • Erase DTC

TIMING CHART

Infomation Display (combination Meter)

Indicator/Information

ItemSymbolFunction
Auto engine shutoff system indicator
  • While Auto engine shutoff system is in operation, the system displays the announcement from 30 seconds before engine automatically stop.

  • When opening the driver's door's door, normal display and announce display will display in 2 - 3 seconds interval.

  • When the driver's door is closed, always displays the announce.

  • Countdown timer will display until the engine automatically stops.

  • System can be continue or cancel by steering switch operation

    OK:System continue

    Disable:System cancel

ASCD indicator
For detail of ASCD function, refer to System Description.
Oil control system (OCS) indicator
For detail of OCS function, refer to System Description.

Engine warning

DESIGN/PURPOSE

Warn the driver that the state of the engine.

SymbolMessage
  • Engine Stalled Stop safely

  • Engine Malfunction Power reduced Service now

  • Engine Malfunction Service now

  • Engine hot Power reduced

BULB CHECK

Not applicable

OPERATION AT COMBINATION METER CAN COMMUNICATION CUT-OFF OR UNUSUAL SIGNAL

For the operation for CAN communications blackout or abnormal signal reception, Fail-Safe (FULL TFT METER) or Fail-Safe (7 INCH INFORMATION DISPLAY).

SYSTEM DIAGRAM

SIGNAL PATH

ECM transmits the engine warning display signal to combination meter via CAN communication.

Then the engine warning displays.

LIGHTING CONDITION

When all of the following conditions is satisfied:

  • Ignition switch: ON

  • Failure of powertrain which may cause serious accident is detected.

  • Driving condition may cause accident or situation that car cannot run.

SHUTOFF CONDITION

When any of the following conditions is satisfied:

  • Ignition switch: OFF

  • Failure of powertrain which may cause serious accident is not detected.

  • No problem about driving condition.

TIMING CHART

t : 100 ms

Warning Chime

Stop/Start warning

PURPOSE

The combination meter alerts the driver by sounding the integrated buzzer and blinking the indicator lamp at high speed when the driver′s operation is judged as improper operation while the stop/start system is operating.

SYNCHRONIZATION WITH WARNING/INDICATOR (INFORMATION DISPLAY)

Applicable

For warning/indicator (information display), refer to Indicator/Information.

SYSTEM DIAGRAM

SIGNAL PATH

  • IPDM E/R transmits a hood switch signal to ECM via CAN communication.

  • BCM transmits a door switch signal to ECM via CAN communication.

  • The combination meter transmits a seat belt buckle switch signal to ECM via CAN communication.

  • ECM judges a stop/start system warning according to a received signal and transmits a stop/start indicator lamp request signal to the combination meter via CAN communication.

  • The combination meter sounds the warning buzzer and blinks the indicator lamp when receiving a stop/start indicator lamp request signal.

When the following conditions are satisfied during stop/start system operation:

  • Hood is opened.

  • Stop/start system is cancelled after the hood is opened.

  • Driver′s door is closed.

  • Driver′s seat belt is buckled.

TIMING CHART

SOUND SPECIFICATION

Warning/indicator/chime List

Warning Lamp/Indicator Lamp

ItemDesignReference
Engine Oil Pressure Warning Lamp Regarding the function. Refer to Engine Oil Pressure Warning Lamp.
Malfunction indicator lamp (MIL) Regarding the function. Refer to Malfunction Indicator Lamp (MIL).

Warning/Indicator (On Information Display)

ItemReference
ASCD indicator Refer to Indicator/Information.
Engine warning Refer to Engine warning.
Oil control system (OCS) indicator Refer to Indicator/Information.
Stop/Start indicator Refer to Switch Name and Function.

Warning Chime

ItemReference
Stop/Start warning Refer to Stop/Start warning.