Front Axle - Front Drive Shaft
Disassembly and Assembly (LH)

| 1. | Circlip | 2. | Dust shield | 3. | Slide joint housing |
| 4. | Snap ring | 5. | Spider assembly | 6. | Stopper ring |
| 7. | Boot band | 8. | Boot | 9. | Shaft |
| 10. | Damper band | 11. | Damper | 12. | Boot band |
| 13. | Boot | 14. | Circlip | 15. | Joint sub-assembly |
| Front |
DISASSEMBLY
Transaxle Side
Secure front drive shaft in a vise.
Remove boot bands and slide the boot back.
Remove circlip and dust shield from slide joint housing.
Put matching marks on slide joint housing and shaft before separating joint assembly.
Remove stopper ring with a suitable tool, then pull out slide joint housing.

Put matching mark (A) on spider assembly and shaft.

Remove snap ring (1) using a suitable tool, then remove spider assembly from shaft.

Remove boot from shaft.
Clean the old grease off of the slide joint assembly.
Wheel Side
Secure the front drive shaft in a vise.
Remove boot bands and slide the boot back.
Screw a suitable tool (A) 30 mm (1.18 in) or more into threaded part of joint sub-assembly. Pull joint sub-assembly out of shaft.

Remove boot from shaft.
Remove circlip from shaft.
While rotating ball cage, clean the old grease off of the joint sub-assembly.
Damper
Remove damper bands, then remove damper from shaft.
INSPECTION AFTER DISASSEMBLY
Shaft
Replace shaft if there is bending, cracking, or other damage.
Joint Sub-Assembly
Make sure there is no rough rotation or unusual axial looseness.
Make sure there is no foreign material inside joint sub-assembly.
Check joint sub-assembly for compression scars, cracks or fractures.
Slide Joint Housing
Make sure there are no compression scars, cracks or fractures or unusual wear of ball rolling surface.
Make sure there is no damage to shaft screws.
Make sure there is no deformation of boot installation parts.
Ball Cage
Make sure there are no compression scars, cracks, fractures of sliding surface.
Steel Ball
Make sure there are no compression scars, cracks, fractures or unusual wear.
Inner Race
Check ball sliding surface for compression scars, cracks or fractures.
Make sure there is no damage to serrated part.
Damper
Check damper for cracks or wear. Install damper with new damper bands.
ASSEMBLY
Transaxle Side
Install new boot and new small boot band on shaft.

Remove protective tape wound around serrated part of shaft.
Install spider assembly securely, making sure the matching marks which were made during disassembly are properly aligned.
Install new snap ring (1) using a suitable tool.

Pack drive shaft with specified amount of new grease (Genuine NISSAN Grease or equivalent).
| Grease quantity | : Refer to Drive Shaft . |
Install new stopper ring to housing of slide joint assembly.
After installation, pull shaft to check engagement between slide joint assembly and stopper ring.
Install boot securely into grooves (indicated by * marks) as shown.

Make sure boot installation length (L) is the length specified below. Insert a suitable tool into the large end of boot. Bleed air from boot to prevent boot deformation.
| Boot installation length (L) | : Refer to Drive Shaft. |
Secure large and small ends of boot with new boot bands as shown.

Install new dust shield to slide joint housing.
After installing housing and shaft, make sure boot position is correct. If boot position is not correct, remove old boot bands then reposition the boot and secure with new boot bands.
Wheel Side
Insert the amount of grease (Genuine NISSAN Grease or equivalent) into joint sub-assembly (1) serration hole until grease begins to ooze from ball groove and serration hole. After inserting grease, use a shop cloth to wipe off old grease that has oozed out.

Cover serrated part of shaft with tape (A). Install new boot band and boot to shaft. Be careful not to damage boot.

Remove protective tape wound around serrated part of shaft.
Attach new circlip to shaft. The circlip must fit securely into shaft groove. Attach nut to joint sub-assembly. Use a suitable tool to press-fit.

Insert the amount of new grease (Genuine NISSAN Grease or equivalent) listed below into housing from large end of boot.
| Grease quantity | : Refer to Drive Shaft. |
Install boot securely into grooves (indicated by * marks) as shown.

Make sure boot installation length (L) is the specified length indicated below. Insert a suitable tool into the large end of boot. Bleed air from boot to prevent boot deformation.
| Boot installation length (L) | : Refer to Drive Shaft. |
Install new large and small boot bands securely using Tool.

| Tool number | : KV40107300 (NI-51751) |
Secure boot band so that dimension (M) meets specification as shown.

Dimension (M) : Refer to Boot Bands.
After installing housing and shaft, rotate boot to check whether or not the actual position is correct. If boot position is not correct, remove old boot bands, then reposition the boot and secure with new boot bands.
Damper
Use new damper bands for installation.

Install damper from stationary-joint side while holding it securely.
| Dimension (A) | : Refer to Dynamic Damper. |
| Dimension (B) | : Refer to Dynamic Damper. |
Disassembly and Assembly (RH)

| 1. | Housing | 2. | Damper bands | 3. | Dynamic damper |
| 4. | Shaft | 5. | Joint sub-assembly | 6. | Circular clip |
| 7. | Boot bands | 8. | Boot | 9. | Stopper ring |
| 10. | Spider assembly | 11. | Snap ring | 12. | Support bearing |
| 13. | Dust shield | Wheel side | |||
| Fill NISSAN Genuine grease or equivalent. | |||||
DISASSEMBLY
Transaxle Side
Press shaft in a vise.
Remove circlip and dust shield from slide joint housing.
Remove boot bands and slide the boots back.
Put matching marks on slide joint housing and shaft before separating slide joint housing.
Remove stopper ring using a suitable tool, then pull out slide joint housing.

Put matching mark (A) on spider assembly and shaft.

Remove snap ring (1) using a suitable tool, then remove spider assembly from shaft.

Remove boot from shaft.
Clean old grease off of the slide joint housing.
Wheel Side
Secure the front drive shaft in a vise.
Remove boot bands and slide the boot back.
Screw a suitable tool (A) 30 mm (1.18 in) or more into threaded part of joint sub-assembly. Pull joint sub-assembly out of shaft.

Remove boot from shaft.
Remove circlip from shaft.
While rotating ball cage, clean the old grease off of the joint sub-assembly.
Support Bearing
Remove dust shield from slide joint assembly using a suitable tool.
Remove snap ring using a suitable tool.
Press support bearing assembly off slide joint assembly using a suitable tool.

Damper (if equipped)
Remove damper bands, then remove damper from shaft.
INSPECTION AFTER DISASSEMBLY
Shaft
Replace shaft if there is any bending, cracking, or other damage.
Joint Sub-assembly
Make sure there is no rough rotation or unusual axial looseness.
Make sure there is no foreign material inside joint sub-assembly.
Check joint sub-assembly for compression scars, cracks or fractures.
Sliding Joint Housing and Spider Assembly
If roller surface of spider assembly has scratches or wear, replace housing and spider assembly.
Support Bearing
Make sure wheel bearing rolls freely and is free from noise, cracks, pitting or wear.
Damper (if equipped)
Check damper for cracks or wear. Install damper with new damper bands.
ASSEMBLY
Transaxle Side
Cover serrated part of shaft with tape (A). Install new boot and boot band onto shaft. Be careful not to damage boot.

Remove protective tape wound around serrated part of shaft.
Install spider assembly securely, making sure the matching marks which were made during disassembly are properly aligned.
Install new snap ring (1) using a suitable tool.

Pack drive shaft with specified amount of grease (Genuine NISSAN Grease or equivalent).
| Grease quantity | : Refer to Drive Shaft. |
Install new stopper ring to slide joint assembly.
After installation, pull shaft to check engagement between slide joint assembly and stopper ring.
Install boot securely into grooves (indicated by * marks) as shown.

Make sure boot installation length (L) is the length indicated below. Insert a suitable tool into the large end of boot. Bleed air from boot to prevent boot deformation.
| Boot installation length (L) | : Refer to Drive Shaft. |
Secure big and small ends of boot with new boot bands as shown.

Install new dust shield to slide joint housing.
After installing housing and shaft, rotate boot to check whether or not the actual position is correct. If boot position is not correct, remove old boot bands then reposition the boot and secure with new boot bands.
Wheel Side
Insert the amount of grease (Genuine NISSAN Grease or equivalent) into joint sub-assembly (1) serration hole until grease begins to ooze from ball groove and serration hole. After inserting grease, use a shop cloth to wipe off old grease that has oozed out.

Cover serrated part of shaft with tape (A). Install new boot and boot band onto shaft. Be careful not to damage boot.

Remove protective tape wound around serrated part of shaft.
Attach new circlip to shaft. The circlip must fit securely into shaft groove. Attach nut to joint sub-assembly. Use a suitable tool to press-fit

Insert the amount of new grease (Genuine NISSAN Grease or equivalent) listed below into housing from large end of boot.
| Grease quantity | : Refer to Drive Shaft. |
Install boot securely into grooves (indicated by * marks) as shown.

Make sure boot installation length (L) is the specified length. Insert a suitable tool into the large end of boot. Bleed air from boot to prevent boot deformation.
| Boot installation length (L) | : Refer to Drive Shaft. |
Install new large and small boot bands securely using Tool.

| Tool number | : KV40107300 (NI-51751) |
Secure boot band so that dimension (M) meets specification as shown.

Dimension (M) : Refer to Boot Bands.
After installing housing and shaft, rotate boot to check whether or not the actual position is correct. If boot position is not correct, remove old boot bands then reposition the boot and secure with new boot bands.
Support Bearing
Install support bearing onto slide joint assembly.
Install snap ring.
Install dust shield.
Damper (if equipped)
Use new damper bands for installation.

Install damper from stationary-joint side while holding it securely.
| Dimension (A) | : Refer to Dynamic Damper. |
| Dimension (B) | : Refer to Dynamic Damper. |