Driver Assistance System - Basic Inspection
- Diagnosis and Repair Work Flow
- Additional Service When Replacing Chassis Control Module
- Configuration
- Mac Key Writing
Diagnosis and Repair Work Flow Nissan Pathfinder 5th Gen
Work Flow
DETAILED FLOW
INTERVIEW FROM THE CUSTOMER
Clarify customer complaints before inspection. First of all, perform an interview utilizing Diagnostic Work Sheet and reproduce the symptom as well as fully understand it. Ask customer about his/her complaints carefully. Check symptoms by driving Nissan Pathfinder vehicle with customer, if necessary.
>>GO TO 2.
CHECK SYMPTOM
Reproduce the symptom that is indicated by the customer, based on the information from the customer obtained by the interview. Also check that the symptom is not caused by fail-safe mode. Refer to Fail-safe.
>>GO TO 3.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “CHASSIS CONTROL”.
Is DTC detected?
YES>>Record or print self-diagnosis results and freeze frame data (FFD). GO TO 4.
NO>>INSPECTION END
PERFORM DTC DIAGNOSIS PROCEDURE
With CONSULT
Perform DTC confirmation procedures for the error-detected system.
Is DTC detected?
YES>>GO TO 5.
NO>>Check harness and connectors based on the information obtained by the interview.
REPAIR OR REPLACE ERROR-DETECTED PARTS
Repair or replace error-detected parts.
Reconnect part or connector after repairing or replacing.
When DTC is detected, erase self-diagnosis results for “CHASSIS CONTROL”.
GO TO 6.
FINAL CHECK
With CONSULT
Check the reference value for “CHASSIS CONTROL”.
Recheck the symptom and check that the symptom is not reproduced on the same conditions.
Is the symptom reproduced?
YES>>GO TO 3.
NO>>INSPECTION END
Diagnostic Work Sheet
Description
In general, customers have their own criteria for a symptom. Therefore, it is important to understand the symptom and status well enough by interviewing the customer about the symptom carefully. To systemize all the information for the diagnosis, prepare the interview sheet referring to the interview points.
In some cases, multiple conditions that appear simultaneously may cause a DTC to be detected.
INTERVIEW SHEET SAMPLE
| Interview sheet | |||||
|---|---|---|---|---|---|
| Customer name | MR/MS | Registration number | Initial year registration | ||
| Nissan Pathfinder Vehicle type | VIN | ||||
| Storage date | Engine / Traction motor | Mileage | km ( Mile) | ||
| Symptom | □ Does not operate ( | ) function | |||
| □ Warning lamp for ( | ) turns ON. | ||||
| □ Noise □ Vibration | |||||
□ Other ( |
) | ||||
| First occurrence | □ Recently □ Other ( | ) | |||
| Frequency of occurrence | □ Always □ Under a certain conditions of □ Sometimes ( time(s)/day) | ||||
| Climate conditions | □ Irrelevant | ||||
| Weather | □ Fine □ Cloud □ Rain □Snow □ Others ( | ) | |||
| Temperature | □ Hot □Warm □ Cool □ Cold □ Temperature [Approx. | °C ( °F)] | |||
| Relative humidity | □ High □ Moderate □ Low | ||||
| Road conditions | □ Urban area □ Suburb area □ Highway □ Mountainous road (uphill or downhill) □ Rough road |
||||
| Operating condition, etc. | □Irrelevant □When traction motor starts □ During idling □ During driving □ During acceleration □ At constant speed driving □ During deceleration □ During cornering (right curve or left curve) □ When steering wheel is steered (to right or to left) |
||||
| Other conditions | |||||
Nissan Pathfinder Vehicle equipment |
|||||
| Memo | |||||
Additional Service When Replacing Chassis Control Module Nissan Pathfinder 2022
Description
When replacing the chassis control module, the procedures of BEFORE REPLACEMENT and AFTER REPLACEMENT must be performed. For work procedure, refer to the following:
BEFORE REPLACEMENT
When replacing the chassis control module, save “Operation log”.
AFTER REPLACEMENT
After replacing the chassis control module, the following items must be performed:
Chassis control module programming
Chassis control module configuration
Writing MAC key
Work Procedure [Before Replacing Chassis Control Module]
SAVE “OPERATION LOG”
With CONSULT
Save “Operation Log”, according to the procedure of “Programming” in CONSULT Operation Manual.
>>Replace the chassis control module. Refer to Removal and Installation.
After replacing the chassis control module, perform necessary work. Refer to Work Procedure [After Replacing Chassis Control Module].
Work Procedure [After Replacing Chassis Control Module]
CHECK “OPERATION LOG”
With CONSULT
Check “Operation Log” saved before replacing the chassis control module, according to the procedure of “Programming” in CONSULT Operation Manual.
Is there an applicable Operation Log in the Saved Data List?
YES>>GO TO 2.
NO>>GO TO 3.
PERFORM CHASSIS CONTROL MODULE PROGRAMMING
With CONSULT
Perform chassis control module programming, according to “Programming” of CONSULT Operation Manual. Refer to CONSULT Operation Manual.
Ignition switch: ON
Electric load: OFF
Brake pedal: Not depressed
12V battery voltage: 12 – 13.5 V (Check the value displayed on the CONSULT screen.)
GO TO 5.
READ IN CHASSIS CONTROL MODULE PART NUMBER BY EPC LINKED
Obtain chassis control module part number by EPC (service parts catalog), according to the procedure of EPC linked in CONSULT Operation Manual. Refer to CONSULT Operation Manual.
>>GO TO 4.
PERFORM PROGRAMMING (EPC LINKED)
With CONSULT
Perform chassis control module programming according to the procedure of EPC linked in CONSULT Operation Manual. Refer to CONSULT Operation Manual.
Ignition switch: ON
Electric load: OFF
Brake pedal: Not depressed
12V battery voltage: 12 – 13.5 V (Check the value displayed on the CONSULT screen.)
GO TO 5.
PERFORM CONFIGURATION
With CONSULT
Perform configuration. Refer to Description.
>>GO TO 6.
WRITING MAC KEY
With CONSULT
Perform MAC key writing. Refer to Description.
>>GO TO 7.
PERFORM NECESSARY WORK
Perform self-diagnosis for “CHASSIS CONTROL”.
Erase the memory of self-diagnosis results.
End of work.
Configuration Nissan Pathfinder SUV
Description
Vehicle specification needs to be written with CONSULT because it is not written after replacing the chassis control module.
The configuration requires network connection. CONSULT connects to network and then it downloads the configuration data from the server. Then CONSULT writes the Nissan Pathfinder vehicle specification to the chassis control module.
Refer to Work Procedure.
The configuration no need to “save” configuration data from the chassis control module. The configuration data is always generated freshly at the server and then downloaded to the CONSULT.
Work Procedure
WRITING VEHICLE SPECIFICATION
With CONSULT
Perform writing Nissan Pathfinder vehicle specification to chassis control module following "Automatic Configuration" procedure of "Configuration" according to CONSULT Operation Manual.
>>WORK END
Mac Key Writing Nissan Pathfinder R53
Description
When replacing chassis control module, it is necessary to write MAC key to chassis control module. Write MAC key to chassis control module according to "MAC Key writing" procedure of "CONSULT Operation Manual". Refer to Work Procedure.
Ignition switch ON
CONSULT is connected to internet
Work Procedure
PERFORM MAC KEY WRITING
Ignition switch ON.
Select "MAC Key writing" on "Work Support" of "CHASSIS CONTROL" using CONSULT.
Touch "Write".
WORK END