Seat - Second Row Seats
Exploded View
CAPTAIN SEAT RH 
| 1. | Headrest | 2. | Headrest holder (locked) | 3. | Headrest holder (free) |
| 4. | Seatback trim | 5. | Side air bag module bracket (For USA and Canada) | 6. | Rear side air bag module (For USA and Canada) |
| 7. | Seatback side inner cover upper | 8. | Recliner release cable | 9. | Seatback side outer cover lower |
| 10 | Reclining device cover | 11. | Seat cushion outer finisher (RH) | 12. | Recline lever |
| 13. | Second row seat outer leg cover (RH) | 14. | Seat cushion inner finisher (RH) | 15. | Recline release cable assembly |
| 16. | Front slide finisher (RH) | 17. | Seat cushion trim | 18. | Front slide finisher (LH) |
| 19. | Seat harness | 20. | Slide finisher | 21. | Center cushion bracket |
| 22. | Second row seat power walk in control unit | 23. | Seat belt buckle (RH) | 24. | Seat cushion inner finisher (LH) |
| 25. | Seat cushion outer finisher (LH) | 26. | Second row seat outer leg cover (LH) | 27. | Armrest cover (with captain’s seat) |
| 28. | Armrest (with captain’s seat) | 29. | Seatback side inner cover lower | 30. | Seatback side inner cover upper |
| 31. | Seat walk in motor | 32. | Walk in back switch | 33. | Striker cover (RH) |
| 34. | Striker cover (LH) | 35. | Rear slide finisher (RH) | 36. | Rear slide finisher (LH) |
| 37. | Seatback board | 38. | Tether anchor finisher | 39. | Walk in back switch finisher |
| A. | Seatback pad (not serviceable) | B. | Refer to Removal and Installation. | C. | Seat cushion pad (not serviceable) |
| D. | Seat frame assembly (not serviceable) |
CAPTAIN SEAT LH 
| 1. | Headrest | 2. | Headrest holder (free) | 3. | Headrest holder (locked) |
| 4. | Seatback trim | 5. | Seatback side inner cover upper | 6. | Seat walk in motor |
| 7. | Armrest | 8. | Armrest cover | 9. | Seat outer finisher (RH) |
| 10. | Second row seat outer leg cover (RH) | 11. | Seat belt buckle (LH) | 12. | Seat cushion inner finisher (RH) |
| 13. | Seatback side inner cover lower | 14. | Slide finisher | 15. | Seat cushion trim |
| 16. | Front slide finisher (RH) | 17. | Front slide finisher (LH) | 18. | Center cushion bracket |
| 19. | Seat harness | 20. | Second row seat outer leg cover (LH) | 21. | Seat cushion inner finisher (LH) |
| 22. | Seat cushion outer finisher (LH) | 23. | Recliner lever | 24. | Rear side air bag module (For USA and Canada) |
| 25. | Side air bag module bracket (For USA and Canada) | 26. | Recline release cable assembly | 27. | Reclining device cover |
| 28. | Seatback side outer cover lower | 29. | Recliner release cable | 30. | Seatback side outer cover upper |
| 31. | Striker cover (LH) | 32. | Striker cover (RH) | 33. | Walk in back switch |
| 34. | Rear slide finisher (LH) | 35. | Rear slide finisher (RH) | 36. | Tether anchor finisher |
| 37. | Walk in back switch finisher | 38. | Seatback board | A. | Seatback pad (not serviceable) |
| B. | Refer to Removal and Installation. | C. | Seat cushion pad (not serviceable) | D. | Seat frame assembly (not serviceable) |
BENCH SEAT LH 
| 1. | Headrest (LH) | 2. | Headrest (center) (trim) | 3. | Headrest (center) (pad) |
| 4. | Headrest holder (locked) | 5. | Headrest holder (free) | 6. | Seat belt retractor finisher |
| 7. | Seat belt retractor (center) | 8. | Cup holder | 9. | Armrest hinge finisher |
| 10. | Armrest hinge | 11. | Center armrest trim | 12. | Center armrest pad |
| 13. | Seat belt buckle (center) | 14. | Seat belt buckle (LH) | 15. | Armrest bracket |
| 16. | Seat walk in motor | 17. | Seatback side inner cover upper 1 | 18. | Seatback side inner cover lower |
| 19. | Seat cushion inner finisher (RH) | 20. | Seat cushion outer finisher (RH) | 21. | Second row seat outer leg cover (RH) |
| 22. | Slide finisher | 23. | Seat cushion trim | 24. | Front slide finisher (RH) |
| 25. | Front slide finisher (LH) | 26. | Center cushion bracket | 27. | Seat harness |
| 28. | Seat cushion inner finisher (LH) | 29. | Second row seat outer leg cover (LH) | 30. | Recline lever |
| 31. | Seat cushion outer finisher (LH) | 32. | Seatback side outer cover lower | 33. | Seatback side outer cover upper |
| 34. | Recline release cable assembly | 35. | Recliner release cable | 36. | Rear side air bag module (For USA and Canada) |
| 37. | Side air bag module bracket (For USA and Canada) | 38. | Rear slide finisher (LH) | 39. | Rear slide finisher (RH) |
| 40. | Seatback trim | 41. | Seatback side inner cover upper 2 | 42. | Walk in back switch |
| 43. | Striker cover (RH) | 44. | Striker cover (LH) | 45. | Seatback board |
| 46. | Walk in back switch finisher | 47. | Tether anchor finisher | 48. | Armrest panel |
| A. | Refer to Removal and Installation. | B. | Seat cushion pad (not serviceable) | C. | Seat frame assembly (not serviceable) |
| D. | Seatback pad (not serviceable) |
Removal and Installation
SEAT RH
Removal
Disconnect negative and positive battery terminals, then wait at least three minutes. Refer to Battery Disconnect.
Remove the headrest.
Slide the seat to the full rearward position.
Using a suitable tool, release clips and remove the front slide finisher [RH (1)] and front slide finisher [LH (2)] in the direction shown.

![]() |
: Metal clip |
Disconnect the harness connector, then release from seat frame assembly.
Remove the front seat bolts.
Slide the seat to the full forward position.
Using a suitable tool, release clips and remove the rear slide finisher [LH (1)] and rear slide finisher [RH (2)] in the direction shown.

![]() |
: Metal clip |
Remove the rear seat bolts.
Remove all necessary clips.
Fold the seatback in the flat position, then remove the seat from the Nissan Pathfinder vehicle.
Installation
Installation is in the reverse order of removal.
CAPTAIN SEAT LH AND BENCH SEAT LH
Removal
Disconnect negative and positive battery terminals, then wait at least three minutes. Refer to Battery Disconnect.
Remove the headrest.
Slide the seat to the full rearward position.
Using a suitable tool, release clips and remove the front slide finisher [RH (1)] and front slide finisher [LH (2)] in the direction shown.

![]() |
: Metal clip |
Disconnect the harness connector, then release from seat frame assembly.
Remove the front seat bolts.
Slide the seat to the full forward position.
Remove the rear slide finishers using the following step:
For captain seat LH, release clips and remove the rear slide finisher [LH (1)] and rear slide finisher [RH (2)] in the direction shown.


: Metal clip For bench seat LH, release clips and remove the rear slide finisher [LH (1)] and rear slide finisher [RH (2)] in the direction shown.


: Metal clip
Remove the rear seat bolts.
Remove all necessary clips.
Fold the seatback in the flat position, then remove the seat from the Nissan Pathfinder vehicle.
Installation
Installation is in the reverse order of removal.
- Center Armrest
- Second Row Seat Heater
- Second Row Seat Power Walk in Control Unit
- Seat Walk in Motor
- Walk in Side Switch
- Walk in Back Switch
- Recliner Release Cable
- Recline Release Cable Assembly
Center Armrest Nissan Pathfinder SUV
Removal and Installation
REMOVAL
Fold down the RH seatback.
Fold down the center armrest.
Using suitable tool, release pawls and remove the armrest bracket outer finisher (1).

![]() |
: Front |
![]() |
: Pawl |
Remove nuts (A) and remove the center armrest (1).

![]() |
: Front |
If necessary, using suitable tool, release pawls and remove the cup holder (1) from the center armrest (2).

![]() |
: Pawl |
INSTALLATION
Installation is in the reverse order of removal.
Second Row Seat Heater Nissan Pathfinder
Removal and Installation
Seat Cushion
The second row seat heater is serviced as part of the seat cushion. For disassembly and assembly of the seat cushion, refer to Seat Cushion (Captain Seat LH), Seat Cushion (Seat RH), or Seat Cushion (Bench Seat LH).
Seat Back Heater
The second row seat back heater is serviced as part of the seatback. For disassembly and assembly of the seatback, refer to Seatback (Captain Seat LH), Seatback (Seat RH), or Seatback (Bench Seat LH).
Second Row Seat Power Walk in Control Unit Nissan Pathfinder Fifth generation
Removal and Installation
REMOVAL
Remove seat cushion (RH). Refer to Seat Cushion.
Release hooks (A) and position seat cushion bracket (1) aside.

Disconnect the harness connector (A) from the second row seat power walk in control unit (1).

Using suitable tool, release harness retainer from the second row seat power walk in control unit (1).
Remove screws (B) and remove the second row seat power walk in control unit (1) from the seat frame (2).
INSTALLATION
Installation is in the reverse order of removal.
Seat Walk in Motor Nissan Pathfinder SUV
Removal and Installation
REMOVAL
Remove the seatback. Refer to Seatback (Seat RH), Seatback (Captain seat LH), or Seatback (Bench Seat LH).
Remove screws (A) from the seat walk in motor (1).

Disconnect the harness connector from the seat walk in motor.
Using suitable tool, release pawls and release the track tilt release cable (1) from the seat walk in motor (2).

![]() |
: Pawl |
Remove the seat walk in motor.
INSTALLATION
Installation is in the reverse order of removal.
Walk in Side Switch Nissan Pathfinder 5th Gen
Removal and Installation
The walk in side switch is serviced as part of the seat cushion outer finisher [RH (seat RH)], seat cushion outer finisher [LH (captain seat LH), or seat cushion outer finisher [LH (bench seat LH)]. For removal and installation of the seat cushion outer finisher, refer to Seat Cushion (Seat RH), Seat Cushion (Captain seat LH), or Seat Cushion (Bench seat LH).
Walk in Back Switch Nissan Pathfinder R53
Removal and Installation
REMOVAL
Remove the seatback pad and trim. Refer to Seatback (Seat RH), Seatback (Captain seat LH), or Seatback (Bench seat LH).
Disconnect the harness connector (A) from the walk in back switch (1).

Remove screws (A) and remove the walk in back switch (1).

INSTALLATION
Installation is in the reverse order of removal.
Recliner Release Cable Nissan Pathfinder R53
Removal and Installation
Removal
Remove the seat cushion. Refer to Seat Cushion (Seat RH), Seat Cushion (Captain seat LH), Seat Cushion (Bench seat LH).
Remove the seat walk in motor. Refer to Removal and Installation.
Remove screws (A) and remove the seat cushion inner finisher [RH (1)].

Remove screws (A) and remove the seat cushion inner finisher [LH (1)].

Remove the recliner release cables (1) from the brackets (A).

Using a suitable tool, release cable retainers from the recliner release cable and remove the recliner release cable from the seat frame assembly.
Installation
Installation is in the reverse order of removal.
Make sure the recline release cable assembly strap (A) is routed through the seat cushion inner finisher [RH (1)].

Recline Release Cable Assembly Nissan Pathfinder 2022
Removal and Installation
Removal
Remove the seat cushion. Refer to Seat Cushion (Seat RH), Seat Cushion (Captain seat LH), Seat Cushion (Bench seat LH).
Remove the recline release cable assembly screws (A).

Remove the recline release cable (1) from the seat frame assembly in the direction shown.

Remove recline release cable assembly (1) from bracket (2) in direction shown.

Using a suitable tool, release clips from the recline release cable assembly, then remove recline cable assembly from the seat frame assembly.
Installation
Installation is in the reverse order of removal.
Make sure the recline release cable assembly strap (A) is routed through the seat cushion inner finisher [LH (1)].








