Power Control System - Ipdm E/r

In this manual: Power Control System - Ipdm E/r
General Information — 8Engine :: Engine Mechanical — 19Engine Lubrication System - Precautions. Preparation — 1Engine Lubrication System - Lubrication System (System Description). Engine Oil Pressure (Basic Inspection). Service Data and Specifications (SDS) — 1Engine Cooling System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Engine Cooling System - Engine Coolant — 1Engine Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Engine Control System - Ecu Diagnosis Information — 1Ecu Diagnosis Information - Ecm ++ — 1Engine Control System - Basic Inspection — 1Basic Inspection - Diagnosis and Repair Workflow ++ — 1Basic Inspection - Basic Inspection ++ — 1Basic Inspection - Additional Service When Replacing Ecm ++ — 1Basic Inspection - Fuel Pressure Check ++ — 1Basic Inspection - How to Set Srt Code ++ — 1Basic Inspection - How to Erase Permanent Dtc ++ — 1Engine Control System - Dtc/circuit Diagnosis — 1Engine Control System - Symptom Diagnosis — 1Engine Control System - Periodic Maintenance — 1Engine Control System - Removal and Installation — 1Fuel System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Fuel System - Fuel System (Periodic Maintenance). Fuel Level Sensor Unit (Disassembly and Assembly) — 1Exhaust System - Precautions. Preparation — 1Exhaust System - Exhaust System (Periodic Maintenance). Exhaust System (Removal and Installation) — 1Starting System - Precautions. Preparation. Starter Motor (Service Data and Specifications (sds)) — 1Starting System - Diagnosis and Repair Work Flow — 1Starting System - Starting System (Symptom Diagnosis). Starter Motor (Removal and Installation) — 1Accelerator Control System - Precautions. Service Data and Specifications (SDS) — 1Accelerator Control System - Accelerator Pedal Assembly — 1Transmission & Driveline :: Transaxle & Transmission — 21Driveline - System Description — 1Transfer: Ty92b - Ecu Diagnosis Information. Awd Control Unit ++ — 1Driveline - Basic Inspection — 1Driveline - Dtc/circuit Diagnosis — 1Driveline - Symptom Diagnosis — 1Driveline - Removal and Installation — 1Transfer: Ty92b - Unit Removal and Installation. Transfer Assembly ++ — 1Driveline - Unit Disassembly and Assembly — 1Driveline - Basic Inspection — 1Driveline - Removal and Installation — 1Driveline - Unit Disassembly and Assembly — 1Front Axle - Precautions. Preparation — 1Front Axle - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Front Axle - Front Drive Shaft Boot — 1Front Axle - Front Drive Shaft — 1Rear Axle - Precautions. Preparation. Service Data and Specifications (SDS) — 1Rear Axle - Noise, Vibration and Harshness (nvh) Troubleshooting — 1Rear Axle - Rear Drive Shaft — 1Suspension :: Front Suspension — 7Rear Suspension - Precautions. Preparation — 1Rear Suspension - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Rear Suspension - Rear Suspension Assembly — 1Road Wheels & Tires - Precautions — 1Road Wheels & Tires - Preparation. Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Road Wheels & Tires - System — 1Brakes :: Brake System — 9Parking Brake System - Precautions. Preparation — 1Parking Brake System - System — 1Vdc/tcs/abs - Precautions ++ — 1Brake Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Dtc/circuit Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Steering :: Steering System — 9Steering Control System - Precautions — 1Steering Control System - System — 1Steering Control System - Eps Control Unit (Ecu Diagnosis Information. Removal and Installation) — 1Restraints :: Seat Belt — 7Srs Air Bag - Precautions. Preparation — 1Srs Air Bag - Collision Diagnosis — 1Srs Air Bag - Occupant Classification System — 1Srs Air Bag Control System - Precautions — 1Srs Air Bag Control System - System — 1Srs Air Bag Control System - Diagnosis Sensor Unit — 1Srs Air Bag Control System - Inspection and Adjustment — 1Ventilation, Heater & Air Conditioner :: Ventilation System — 6Heater & Air Conditioning System - Precautions — 1Heater & Air Conditioning System - Preparation — 1Heater & Air Conditioning System - Component Parts — 1Heater & Air Conditioning System - Diagnosis and Repair Work Flow — 1Heater & Air Conditioning System - Compressor — 1Heater & Air Conditioning System - Cooler Pipe and Hose — 1Heater & Air Conditioning System - Condenser. Condenser — 1Heater & Air Conditioning System - Heating and Cooling Unit Assembly — 1Heater & Air Conditioning System - Service Data and Specifications (SDS) — 1Heater & Air Conditioning Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1Heater & Air Conditioning Control System - Ecu Diagnosis Information — 1Heater & Air Conditioning Control System - Basic Inspection — 1Heater & Air Conditioning Control System - Dtc/circuit Diagnosis — 1Heater & Air Conditioning Control System - Symptom Diagnosis — 1Heater & Air Conditioning Control System - Removal and Installation — 1Body Interior :: Interior — 8Instrument Panel - Precautions. Preparation. Clip List — 1Instrument Panel - Squeak and Rattle Trouble Diagnoses — 1Instrument Panel - Cluster Lid C — 1Seat - Precautions — 1Seat - Preparation. Clip List — 1Seat - Component Parts — 1Seat - System — 1Seat - Diagnosis and Repair Work Flow — 1Seat - Front Seat — 1Seat - Second Row Seats — 1Seat - Third Row Seats — 1Seat - Front Seat — 1Seat - Second Row Seat — 1Seat - Third Row Seat — 1Automatic Drive Positioner - Precautions. Preparation — 1Automatic Drive Positioner - System — 1Automatic Drive Positioner - Diagnosis and Repair Work Flow — 1Automatic Drive Positioner - Inspection and Adjustment — 1Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock — 38Security Control System - Precautions — 1Security Control System - System — 1Security Control System - Ecm, Bcm, Intelligent Key Unit, Ipdm E/r — 1Security Control System - Vehicle Security System Cannot Be Set — 1Glass & Window System - Precautions. Preparation — 1Glass & Window System - Squeak and Rattle Trouble Diagnoses — 1Power Window Control System - Precautions. Preparation — 1Power Window Control System - Power Supply and Ground Circuit — 1Power Window Control System - Power Window Motor Circuit — 1Power Window Control System - Front Power Window Rh Alone Does Not Operate — 1Power Window Control System - Rear Lh Side Power Window Alone Does Not Operate — 1Power Window Control System - Rear Rh Side Power Window Alone Does Not Operate — 1Roof - Precautions. Preparation — 1Roof - Power Supply and Ground Circuit — 1Roof - Moonroof Switch Assembly — 1Roof - Lin Communication Circuit — 1Roof - Auto Operation Does Not Operate — 1Roof - Anti-Pinch Function Does Not Operate — 1Exterior - Precautions. Preparation. Clip List (Preparation) — 1Exterior - Squeak and Rattle Trouble Diagnoses — 1Exterior - Fender Protector — 1Exterior - Over Fender — 1Exterior - Under Cover — 1Exterior - Roof Side Rail — 1Body Repair - Service Information — 1Service Information - Sheet Metal Work ++ — 1Service Information - Body Welding and Precautions ++ — 1Service Information - Safety and Health ++ — 1Service Information - Repairing Procedures and Precautions ++ — 1Body Repair - Precaution — 1Body Repair - Preparation — 1Body Repair - Removal and Installation — 1Driver Controls :: Mirrors — 8Exterior Lighting System - System Description — 1System Description - Component Parts ++ — 1Exterior Lighting System - Basic Inspection — 1Exterior Lighting System - Dtc/circuit Diagnosis — 1Exterior Lighting System - Symptom Diagnosis — 1Exterior Lighting System - Periodic Maintenance — 1Exterior Lighting System - Removal and Installation — 1Interior Lighting System - Precautions. Preparation — 1Interior Lighting System - Component Parts. Interior Lighting System — 1Interior Lighting System - System — 1Interior Lighting System - Diagnosis and Repair Work Flow — 1Interior Lighting System - Interior Lighting System Symptoms (Symptom Diagnosis). Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Interior Lighting System - Foot Lamp — 1Wiper & Washer - Precautions — 1Wiper & Washer - Preparation. Bcm, Ipdm E/r (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Wiper & Washer - System — 1Wiper & Washer - Diagnosis and Repair Work Flow — 1Defogger - Precautions. Bcm, A/c Auto Amp. (Ecu Diagnosis Information) — 1Defogger - Diagnosis and Repair Work Flow — 1Horn - Precautions — 1Electrical & Power Control :: Power Outlet — 13Body Control System - Precautions. Preparation — 1Body Control System - Component Parts — 1Body Control System - System — 1Body Control System - Diagnosis System (bcm) — 1Body Control System - Bcm — 1Lan System - System Description — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - Removal and Installation — 1Charging System - Precautions. Preparation. Ecm, Ipdm E/r (Ecu Diagnosis Information) — 1Charging System - Diagnosis and Repair Work Flow — 1Charging System - Charging System (Symptom Diagnosis). Generator (Removal and Installation). Service Data and Specifications (SDS) — 1Power Supply, Ground & Circuit Elements - Precautions. Preparation. Service Data and Specifications (SDS) — 1Driver Information & Multimedia :: Meter, Warning Lamp & Indicator — 25Warning Chime System - Application Notice (How to Use This Manual). Precautions — 1Warning Chime System - System — 1Warning Chime System - Diagnosis System (combination Meter) — 1Warning Chime System - Bcm, Combination Meter (Ecu Diagnosis Information). Diagnosis and Repair Work Flow (Basic Inspection) — 1Sonar System - Precautions. Preparation — 1Sonar System - Sonar Control Unit — 1Dtc/circuit Diagnosis - B2720 Corner Sensor [rl] ++ — 1Audio, Visual & Navigation System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Multi Av (av Control Unit) ++ — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Symptom Diagnosis - Multi Av System ++ — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Cruise Control & Driver Assistance :: Cruise Control System — 17Driver Assistance System - System Description — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Driver Assistance System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1System Description - Handling Precaution ++ — 1Driver Assistance System - Ecu Diagnosis Information — 1Driver Assistance System - Basic Inspection — 1Basic Inspection - Distance Sensor Alignment ++ — 1Basic Inspection - Camera Aiming Adjustment ++ — 1Basic Inspection - Action Test ++ — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Laser/radar (distance Sensor) ++ — 1Dtc/circuit Diagnosis - Lane Camera (front Camera Unit) ++ — 1Driver Assistance System - Symptom Diagnosis — 1Driver Assistance System - Removal and Installation — 1Driver Assistance System - System Description — 1System Description - System ++ — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Drive Mode System - Precautions — 1Drive Mode System - Component Parts. Drive Mode System — 1Drive Mode System - System — 1Drive Mode System - Diagnosis and Repair Work Flow — 1Drive Mode System - Drive Mode Select Switch Circuit — 1Maintenance - Precautions. Preparation — 1Maintenance - General Maintenance — 1Maintenance - Periodic Maintenance — 1Maintenance - Recommended Fluids and Lubricants — 1Maintenance - Engine Maintenance — 1Maintenance - Chassis and Body Maintenance — 1Engine Lubrication System - Periodic Maintenance — 1Engine Lubrication System - Removal and Installation — 1Engine Cooling System - System Description — 1Engine Cooling System - Removal and Installation — 1Engine Control System - Vq35dd — 1Fuel System - Removal and Installation — 1Starting System - System Description — 1Starting System - Dtc/circuit Diagnosis — 1Driveline - Transfer: Ty92b — 1Driveline - Rear Propeller Shaft: 3fcj-Cvj — 1Driveline - Rear Final Drive: R145 — 1Front Axle - Periodic Maintenance — 1Front Axle - Removal and Installation — 1Rear Axle - Periodic Maintenance — 1Rear Axle - Removal and Installation — 1Rear Suspension - Removal and Installation — 1Road Wheels & Tires - System Description — 1Road Wheels & Tires - Basic Inspection — 1Road Wheels & Tires - Dtc/circuit Diagnosis — 1Road Wheels & Tires - Symptom Diagnosis — 1Road Wheels & Tires - Periodic Maintenance — 1Road Wheels & Tires - Removal and Installation — 1Parking Brake System - System Description — 1Parking Brake System - Basic Inspection — 1Parking Brake System - Dtc/circuit Diagnosis — 1Parking Brake System - Symptom Diagnosis — 1Parking Brake System - Removal and Installation — 1Brake Control System - Vdc/tcs/abs — 1Brake Control System - Automatic Brake Hold — 1Brake Control System - Automatic Emergency Braking — 1Brake Control System - Rear Automatic Braking — 1Steering Control System - System Description — 1Steering Control System - Basic Inspection — 1Steering Control System - Dtc/circuit Diagnosis — 1Steering Control System - Symptom Diagnosis — 1Srs Air Bag - Removal and Installation — 1Srs Air Bag Control System - System Description — 1Srs Air Bag Control System - Basic Inspection — 1Srs Air Bag Control System - Symptom Diagnosis — 1Heater & Air Conditioning System - Symptom Diagnosis — 1Heater & Air Conditioning System - Periodic Maintenance — 1Heater & Air Conditioning Control System - Automatic Air Conditioning — 1Instrument Panel - Removal and Installation — 1Instrument Panel - Unit Disassembly and Assembly — 1Seat - Ecu Diagnosis Information — 1Seat - Dtc/circuit Diagnosis — 1Seat - Symptom Diagnosis — 1Automatic Drive Positioner - System Description — 1Automatic Drive Positioner - Ecu Diagnosis Information — 1Automatic Drive Positioner - Dtc/circuit Diagnosis — 1Automatic Drive Positioner - Symptom Diagnosis — 1Automatic Drive Positioner - Removal and Installation — 1Security Control System - System Description — 1Security Control System - Basic Inspection — 1Security Control System - Dtc/circuit Diagnosis — 1Security Control System - Symptom Diagnosis — 1Security Control System - Removal and Installation — 1Glass & Window System - Removal and Installation — 1Power Window Control System - System Description — 1Power Window Control System - Ecu Diagnosis Information — 1Power Window Control System - Basic Inspection — 1Power Window Control System - Dtc/circuit Diagnosis — 1Power Window Control System - Symptom Diagnosis — 1Power Window Control System - Removal and Installation — 1Roof - System Description — 1Roof - Ecu Diagnosis Information — 1Roof - Basic Inspection — 1Roof - Dtc/circuit Diagnosis — 1Roof - Symptom Diagnosis — 1Roof - Removal and Installation — 1Exterior - System Description — 1Exterior - Removal and Installation — 1Body Repair - Repair Information — 1Exterior Lighting System - Led Headlamp — 1Interior Lighting System - Dtc/circuit Diagnosis — 1Interior Lighting System - Removal and Installation — 1Wiper & Washer - System Description — 1Wiper & Washer - Dtc/circuit Diagnosis — 1Wiper & Washer - Symptom Diagnosis — 1Wiper & Washer - Removal and Installation — 1Defogger - System Description — 1Defogger - Dtc/circuit Diagnosis — 1Defogger - Symptom Diagnosis — 1Defogger - Removal and Installation — 1Horn - Removal and Installation — 1Body Control System - Basic Inspection — 1Body Control System - Dtc/circuit Diagnosis — 1Body Control System - Symptom Diagnosis — 1Body Control System - Removal and Installation — 1Lan System - Can Fundamental — 1Lan System - Can — 1Lan System - Can Gateway — 1Power Control System - Ipdm E/r — 1Power Control System - Power Distribution System — 1Charging System - System Description — 1Charging System - Dtc/circuit Diagnosis — 1Power Supply, Ground & Circuit Elements - System Description — 1Power Supply, Ground & Circuit Elements - Basic Inspection — 1Power Supply, Ground & Circuit Elements - Removal and Installation — 1Warning Chime System - System Description — 1Warning Chime System - Dtc/circuit Diagnosis — 1Warning Chime System - Symptom Diagnosis — 1Sonar System - System Description — 1Sonar System - Basic Inspection — 1Sonar System - Dtc/circuit Diagnosis — 1Sonar System - Symptom Diagnosis — 1Sonar System - Removal and Installation — 1Audio, Visual & Navigation System - Nissanconnect — 1Audio, Visual & Navigation System - Intelligent Around View Monitor System — 1Audio, Visual & Navigation System - Rear View Monitor System — 1Audio, Visual & Navigation System - Telematics System — 1Driver Assistance System - Adas Control Unit 2 — 1Driver Assistance System - Driver Assistance System — 1Driver Assistance System - Chassis Control — 1Drive Mode System - Removal and Installation — 1Dtc/circuit Diagnosis (C053c Wheel Speed Sensor ... U2141 Can Comm Circuit) — 1Dtc/circuit Diagnosis (P0011 Intake Valve Timing Control ... P0111 Iat Sensor) — 1Dtc/circuit Diagnosis (P0116 Engine Coolant Temperature Sensor ... P025b Fuel Pump Module a) — 1Dtc/circuit Diagnosis (P026b Injection Timing ... P0420 Three Way Catalyst Function) — 1Dtc/circuit Diagnosis (P0441 Evap Control System ... P0524 Engine Oil Pressure) — 1Dtc/circuit Diagnosis (P0532 A/c Refrigerant Pressure Sensor ... P064d Ecm) — 1Dtc/circuit Diagnosis (P06da Engine Oil Pressure Control Solenoid Valve ... P1217 Engine Over Temperature) — 1Dtc/circuit Diagnosis (P1220 Fuel Pump Control Module (fpcm) ... P1574 Ascd Vehicle Speed Sensor) — 1Dtc/circuit Diagnosis (P1575 Brake Switch ... P2101 Electric Throttle Control Function) — 1Dtc/circuit Diagnosis (P2118 Throttle Control Motor ... P34ac Electric Intake Valve Timing Control Actuator) — 1Dtc/circuit Diagnosis (Active Grille Shutter ... High Pressure Fuel Pump) — 1Dtc/circuit Diagnosis (Ignition Signal ... Variable Induction Air System) — 14012 C1040 Emergency Brake — 14013 C106a Wheel Sensor — 14014 C1078-55 Not Configuration — 14015 C10b4-98 Overheat — 14016 B1001 Lap Pre-Tensioner Lh — 14017 B0001 Driver Air Bag Module — 14018 B100e Knee Air Bag Module Rh — 14019 B142x Collision Detection — 1Dtc/circuit Diagnosis (B20c7-11 A/c Clutch ... B24a6-11 in-Vehicle Sensor) — 1Dtc/circuit Diagnosis (B24a6-15 in-Vehicle Sensor ... U2140-87 Can Comm Err (ecm)) — 1Dtc/circuit Diagnosis (C1f00-1c Control Unit ... C1f04-61 Brake Sw/stop Lamp Sw) — 1Dtc/circuit Diagnosis (C1f05-49 Front Camera Unit ... C1f70-87 Ethernet Circuit) — 1
~25min read
  • Precautions
  • Ecu Diagnosis Information. Ipdm E/r
  • Removal and Installation. Ipdm E/r (intelligent Power Distribution Module Engine Room)

Precautions Nissan Pathfinder SUV

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER"

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collisions.

Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” sections of this Service Manual.

  • To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in the event of a collision that would result in air bag inflation, it is recommended that all maintenance and repair be performed by an authorized NISSAN/INFINITI dealer.

  • Improper repair, including incorrect removal and installation of the SRS, can lead to personal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag Module, see “SRS AIR BAG”.

  • Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors.

PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS

  • When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the ignition/power switch ON or engine running, never use air or electric power tools or strike near the sensor(s) with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing serious injury.

  • When using air or electric power tools or hammers, always switch the ignition/power switch OFF, disconnect the 12V battery or batteries, and wait at least 3 minutes before performing any service.

Procedure without Cowl TopCover

When performing the procedure after removing cowl top cover, cover the lower end of windshield with urethane, etc. to prevent damage to the windshield.

Ecu Diagnosis Information. Ipdm E/r Nissan Pathfinder Fifth generation

Values on the Diagnosis Tool

MonitorConditionValue/Status
Compressor request 1 Engine running A/C switch OFF Off
A/C switch ON (A/C compressor is operating) On
Easy fill tire alert horn req Off
Cranking enable-TCM Engine crank condition Not satisfied Prohibit
Satisfied Permit
— Stop
Receives invalid CAN signal Unknown
Cranking enable-ECM Engine crank condition Not satisfied Prohibit
Satisfied Permit
— Stop
Receives invalid CAN signal No req
DTRL REQ Engine running Lighting switch 1ST Off
Lighting switch OFF On
COOLING FAN REQ Engine running Cooling fan stop 10%
Cooling fan LO operation 42%
Cooling fan HI operation 90%
FR WIPER REQ Receives invalid CAN signal NG
Ignition switch ON Front wiper HI operation HIGH
Front wiper LO operation LOW
Front wiper forced termination STOP
Front wiper stopped RETURN
HIGH BEAM REQ Lighting switch 2ND Lighting switch LO Off
Lighting switch HI On
Horn request No req
Low beam request Lighting switch OFF Off
Lighting switch 2ND On
POSITION LIGHT REQ Lighting switch OFF Off
Lighting switch 1ST On
IGNITION SW Ignition switch OFF Off
Ignition switch ON On
Ignition switch START START
— No request

FRONT FOG LAMP REQ

Lighting switch 1ST Front fog lamp switch OFF Off
Front fog lamp switch ON On
Shift position Receives invalid CAN signal NG
Engine running Manual mode M
D range D
N range N
R range R
P range P
COMP ECV STATUS ECV control output Normal OK
Malfunction NG
BATTERY VOLTAGE Ignition switch ON 11 V – 14 V
Stop/start status — — —
— — —
FR WIPER STOP POSITION Ignition switch ON Except front wiper stop position ACTIVE P
Front wiper stop position STOP P
IGNITION POWER SUPPLY Off

HOOD SW (CAN)

Open the hood OPEN
Close the hood CLOSE
Transmits invalid CAN signal NG
A/C RELAY Engine running A/C switch OFF Off
A/C switch ON (A/C compressor is operating) On
REVERSE SIGNAL (CAN) Transmits invalid CAN signal NG
Ignition switch ON R range On
Except R range Off
COMP ECV CURRENT Engine running A/C switch OFF 0.00 A
A/C switch ON (A/C compressor is operating) 0.00 A – 1.00 A
Starter&starter cont relay stat Starter relay and starter control relay are OFF Off, Off
Starter relay is ON On, Off
Starter relay and starter control relay are ON On, On
Transmits invalid CAN signal invalid

Hood switch

Close the hood Open
Open the hood Close
IGN RELAY Ignition switch OFF Open
Ignition switch ON Close
Cooling fan relay-2 Engine running Cooling fan stop OFF
  • Cooling fan LO operation

  • Cooling fan HI operation

ON
Compressor Engine running A/C switch OFF OFF
A/C switch ON (A/C compressor is operating ON
Front wiper HI/LO relay Ignition switch ON Except front wiper HI operated OFF
Front wiper HI operated ON
Horn relay OFF
Front wiper relay Ignition switch ON Front wiper stop OFF
Front wiper is operating ON
Battery current sen value (LIN)

Engine running

  • Battery: Full charge

  • Engine Idling

(–200.00) – (+300.00) A
Headlamp warning (LH) (LIN) Lighting switch OFF Open
Lighting switch 2ND Close
Headlamp warning (RH) (LIN) Lighting switch OFF Open
Lighting switch 2ND Close
Compressor ECV duty Engine running A/C switch OFF 0%
A/C switch ON (A/C compressor is operating 0 – 100%
Cooling fan relay-3 Engine running
  • Cooling fan stop

  • Cooling fan LO operated

0%
Cooling fan HI operated 100%

Front fog lamp (LH)

Lighting switch 1ST Front fog lamp switch OFF 0%
Front fog lamp switch ON 100%

Front fog lamp (RH)

Lighting switch 1ST Front fog lamp switch OFF 0%
Front fog lamp switch ON 100%
Tail lamp (LH) Lighting switch OFF 0.0%
Lighting switch 1ST 100.0%
Tail lamp (RH) Lighting switch OFF 0%
Lighting switch 1ST 100%
Headlamp LO (RH) Lighting switch OFF 0%
Lighting switch 2ND 100%
Headlamp LO (LH) Lighting switch OFF 0%
Lighting switch 2ND 100%
Parking lamp (LH) req (LIN)
  • Lighting switch OFF (Except for Canada)

  • Lighting switch AUTO (For Canada)

Close
Lighting switch 1ST Open
DTRL (LH) req (LIN) Engine running and parking brake is released Lighting switch 2ND Close
  • Lighting switch OFF (Except for Canada)

  • Lighting switch AUTO (Only when the illumination judgement by auto light system is OFF) (For Canada)

Open
Headlamp LO (LH) req (LIN)
  • Lighting switch OFF (Except for Canada)

  • Lighting switch AUTO (For Canada)

Close
Lighting switch 2ND Open
Headlamp HI (LH) req (LIN) Lighting switch 2ND Lighting switch LO Close
Lighting switch HI Open
Parking lamp (RH) req (LIN)
  • Lighting switch OFF (Except for Canada)

  • Lighting switch AUTO (For Canada)

Close
Lighting switch 1ST Open
DTRL (RH) req (LIN) Engine running and parking brake is released Lighting switch 2ND Close
  • Lighting switch OFF (Except for Canada)

  • Lighting switch AUTO (Only when the illumination judgement by auto light system is OFF) (For Canada)

Open
Parking/DTRL (LH) output (LIN) Engine running and parking brake is released
  • Lighting switch OFF (Except for Canada)

  • Lighting switch AUTO (Only when the illumination judgement by auto light system is OFF) (For Canada)

100.0%
Lighting switch 2ND 6.0%
Engine stop
  • Lighting switch OFF (Except for Canada)

  • Lighting switch AUTO (Only when the illumination judgement by auto light system is OFF) (For Canada)

0.0%
Parking/DTRL (RH) output (LIN) Engine running and parking brake is released
  • Lighting switch OFF (Except for Canada)

  • Lighting switch AUTO (Only when the illumination judgement by auto light system is OFF) (For Canada)

100.0%
Lighting switch 2ND 6.0%
Engine stop
  • Lighting switch OFF (Except for Canada)

  • Lighting switch AUTO (Only when the illumination judgement by auto light system is OFF) (For Canada)

0.0%
Headlamp HI (RH) req (LIN) Lighting switch 2ND Lighting switch LO Close
Lighting switch HI Open
Headlamp LO (RH) req (LIN)
  • Lighting switch OFF (Except for Canada)

  • Lighting switch AUTO (For Canada)

Close
Lighting switch 2ND Open
Battery status — —
— —
T LAMP LH CIRC MALFUNCTN Tail lamp LH power supply circuit reaches the retry upper limit. 0 – 1
NMB T LAMP LH CIRC RETRY Retry of tail lamp LH power supply circuit is permitted. 0 – 20

Fr fog lamp (LH) circ malfunctn

Front fog lamp LH circuit reaches the retry upper limit. 0 – 1
T LAMP RH CIRC MALFUNCTN Tail lamp RH power supply circuit reaches the retry upper limit. 0 – 1
NMB T LAMP RH CIRC RETRY Retry of tail lamp RH power supply circuit is permitted. 0 – 20
NMB T LAMP RH CIRC SHORT Tail lamp RH power supply circuit detects over current. 0 – 5

NMB F FOG LH CIRC RETRY

Retry of front fog lamp LH circuit is permitted. 0 – 20

NMB F FOG LH CIRC SHORT

Front fog lamp LH circuit detects over current. 0 – 5

F FOG RH CIRC MALFUNCTN

Front fog lamp RH circuit reaches the retry upper limit. 0 – 1

NMB F FOG RH CIRC RETRY

Retry of front fog lamp RH circuit is permitted. 0 – 20

NMB F FOG RH CIRC SHORT

Front fog lamp RH circuit detects over current. 0 – 5
NMB T LAMP LH CIRC SHORT Tail lamp LH power supply circuit detects over current. 0 – 5

BAT DISCHARGE COUNT

Ignition switch ON Less than 65000

Reference Value

TERMINAL LAYOUT

PHYSICAL VALUES

Terminal No.

(Wire color)
DescriptionCondition

Value

(Approx.)
Signal nameInput/Output
+-

1

(L)
Ground Battery power supply Input Ignition switch OFF Battery voltage

2

(G)
Ground Battery power supply Input Ignition switch OFF Battery voltage

4

(W)
Ground Tail lamp LH power supply Output Lighting switch OFF 0 V
Lighting switch 1ST Battery voltage

8

(BG)
Ground ECM relay output Output Ignition switch OFF (more than a few seconds after placing ignition switch ON) 0 V
For a few seconds after placing ignition switch OFF or ignition switch ON Battery voltage

9

(Y)
Ground Horn relay control Input Horn switch OFF Battery voltage
Horn switch ON 0 V

12

(B)
Ground Ground — Ignition switch OFF 0 V

17

(G)
Ground Tail lamp RH power supply Output Lighting switch OFF 0 V
Lighting switch 1ST Battery voltage

22

(P)
Ground CAN-Low Input/Output — —

24

(L)
Ground CAN-High Input/Output — —

31

(B)
Ground Ground — Ignition switch OFF 0 V

33

(BR)
Ground Front wiper auto stop signal Input Ignition switch ON Front wiper stop position 0 V
Other than above Battery voltage

38

(R)
Ground LIN communication (headlamp) Input/output Ignition switch ON

43

(W)
Ground Ignition relay output Output Ignition switch OFF 0 V
Ignition switch ON Battery voltage

45

(L)
Ground Front wiper motor HI power supply Output Ignition switch ON Front wiper switch OFF 0 V
Front wiper switch HI Battery voltage

46

(V)
Ground Fuel pump power supply Output More than a few seconds after placing ignition switch ON or ignition switch OFF 0 V
For a few seconds after placing ignition switch ON or engine running Battery voltage

47

(B)
Ground Ground — Ignition switch ON 0 V

48

(Y)
Ground Front wiper motor LO power supply Output Ignition switch ON Front wiper switch OFF 0 V
Front wiper switch LO Battery voltage

50

(L)
Ground Headlamp (LO) LH power supply Output Lighting switch OFF 0 V
Lighting switch 2ND Battery voltage

511

(Y)
Ground Front fog lamp LH power supply Output Lighting switch 1ST Front fog lamp switch OFF 0 V
Front fog lamp switch ON Battery voltage

52

(R)
Ground Hood switch signal Input Close the hood 0 V
Open the hood Battery voltage

571

(W)
Ground Front fog lamp RH power supply Output Lighting switch 1ST Front fog lamp switch OFF 0 V
Front fog lamp switch ON Battery voltage

62

(P)
Ground Headlamp (LO) RH power supply Output Lighting switch OFF 0 V
Lighting switch 2ND Battery voltage

65

(SB)
Ground A/C compressor power supply Output Engine running A/C switch OFF 0 V

A/C switch ON

(A/C compressor is operating)
Battery voltage

67

(G)
Ground Throttle control motor relay control Input Ignition switch ON –> OFF Battery voltage
Ignition switch ON 0 V

70

(P)
Ground Ignition relay output Output Ignition switch OFF 0 V
Ignition switch ON Battery voltage

71

(L)
Ground Ignition relay output Output Ignition switch OFF 0 V
Ignition switch ON Battery voltage

72

(R)
Ground Throttle control motor relay output Output Ignition switch OFF (more than a few seconds after placing ignition switch ON) 0 V
For a few seconds after placing ignition switch OFF or ignition switch ON Battery voltage

73

(LG)
Ground ECM relay output Output Ignition switch OFF (more than a few seconds after placing ignition switch ON) 0 V
For a few seconds after placing ignition switch OFF or ignition switch ON Battery voltage

75

(W)
Ground ECM relay output Output Ignition switch OFF (more than a few seconds after placing ignition switch ON) 0 V
For a few seconds after placing ignition switch OFF or ignition switch ON Battery voltage

76

(P)
Ground Fuel pump relay control Input Approximately 1 second after placing the ignition switch ON or ignition switch OFF 0 V
Approximately 1 second or more placing the ignition switch ON Battery voltage

78

(L)
Ground ECM relay output Output Ignition switch OFF (more than a few seconds after placing ignition switch ON) 0 V
For a few seconds after placing ignition switch OFF or ignition switch ON Battery voltage

81

(R)
Ground Battery power supply Input Ignition switch OFF Battery voltage

83

(W)
Ground Starter motor power supply Output Other than at engine cranking 0 V
At engine cranking Battery voltage

86

(V)
Ground Starter relay power supply Input Other than at engine cranking 0 V
At engine cranking Battery voltage

91

(R)
Ground LIN communication (battery current sensor) Input/output Ignition switch ON

93

(V)
Ground ECM relay control Input Ignition switch OFF (more than a few seconds after placing ignition switch ON) Battery voltage
For a few seconds after placing ignition switch OFF or ignition switch ON 0 V

98

(W)
Ground A/C compressor (ECV) control Output ECV Duty ratio: 0% (MODE5 or MODE6) 0 V
Duty ratio: 50% (MODE3 or MODE4)
Duty ratio: 100% (MODE1, MODE2 or MODE7) Battery voltage

1042

(L)
Ground Starter switch signal — — —

106

(V)
Ground Cooling fan control Output Engine running Cooling fan stop Battery voltage
  • Cooling fan LO operated

  • Cooling fan HI operated

0 V

107

(B)
Ground Cooling fan control Output Engine running
  • Cooling fan stop

  • Cooling fan LO operated

Battery voltage
Cooling fan HI operated 0 V

1: With front fog lamps or pre-wiring for front fog lamps

2: Except for Mexico

Fail-safe

FAIL-SAFE CONTROL BY DTC

IPDM E/R performs fail-safe control when any DTC are detected.

DTC No.CONSULT displayFail-safe
B121A-11 FR FOG LAMP LH PWR SPLY CIRC [CIRCUIT SHORT TO GROUND] Shuts off the power supply to the front fog lamp LH power supply circuit until the front fog lamp ON conditions are no longer satisfied.
B1256-11 FR FOG LAMP RH PWR SPLY CIRC [CIRCUIT SHORT TO GROUND] Shuts off the power supply to the front fog lamp RH power supply circuit until the front fog lamp ON conditions are no longer satisfied.
B12A4-81 Battery current sensor [INVALID SERIAL DATA RECEIVED] Fix the power generation command value to 14.3 V.
B12A4-92 Battery current sensor [PFM/INCORRECT OPERATN]
B20A2-87 Headlamp (RH) LIN communication [MISSING MESSAGE]
  • Transmits the headlamp warning signal to the combination meter via CAN communication (when the ignition switch is ON, the headlamp warning is displayed on the information display of the combination meter).

  • Transmits the request signal to both side LED headlamp control modules via LIN communication, and turns ON the headlamp (LO) and parking lamp.

B20A4-87 Headlamp (LH) LIN communication [MISSING MESSAGE]
B20C7-11 A/C clutch [CIRCUIT SHORT TO GROUND] Inhibit A/C compressor (magnetic clutch) operation
B20C7-15 A/C clutch [CIRC SHORT TO BATT OR OPEN]
B20C8-14 Compressor (ECV) [CIRC SHORT TO GRND OR OPEN] Inhibit compressor (ECV) operation
B20D4-11 TAIL LAMP LH PWR SPLY CIRC [CIRCUIT SHORT TO GROUND]

Shuts off the power supply to the following power supply circuits until the parking lamp, license plate lamp, side marker lamp and tail lamp ON conditions are no longer satisfied:

  • Front side marker LH

  • Tail lamp LH

  • Rear side marker LH

  • License plate lamp LH

  • License plate lamp RH

B20D5-11 TAIL LAMP RH PWR SPLY CIRC [CIRCUIT SHORT TO GROUND]

Shuts off the power supply to the following power supply circuits until the parking lamp, license plate lamp, side marker lamp and tail lamp ON conditions are no longer satisfied:

  • Front side marker RH

  • Tail lamp RH

  • Rear side marker RH

B20E2-96 LED HEADLAMP RH [CMPNENT INTERNAL MLFNCTN]
  • Transmits the headlamp warning signal to the combination meter via CAN communication (when the ignition switch turns ON, the headlamp warning is displayed on the information display of the combination meter).

  • Transmits the request signal to both side LED headlamp control modules via LIN communication, and turns ON the headlamp (LO) and parking lamp.

B20E3-96 LED HEADLAMP LH [CMPNENT INTERNAL MLFNCTN]
U0073-00 Control module comm Bus A Off [NO SUBTYPE INFO] Refer to CAN COMMUNICATION CONTROL.
U2140-87 CAN comm err (ECM) [MISSING MESSAGE]
U214F-87 CAN comm err (BCM) [MISSING MESSAGE]

CAN COMMUNICATION CONTROL

When CAN communication with the ECM and BCM is impossible, the IPDM E/R performs fail-safe control. After CAN communication recovers normally, it also returns to normal control.

If No CAN Communication Is Available With ECM

Control partFail-safe operation
Cooling fan
  • The cooling fan is operated at HI operation when the ignition switch is placed ON.

  • The cooling fan turns OFF when the ignition switch is placed OFF.

A/C Compressor (magnet clutch) Smart FET OFF

If No CAN Communication Is Available With BCM

Control partFail-safe operation
Headlamp
  • Turns ON the headlamp (LO) when the ignition switch is placed ON.

  • Turns OFF the headlamp (LO) when the ignition switch is placed OFF.

  • Headlamp (HI): OFF

  • Parking lamp

  • License plate lamp

  • Side marker

  • Tail lamp

  • Illumination

  • Turns ON the parking lamp, license plate lamp, side marker lamp, tail lamp and each illumination when the ignition switch is placed ON.

  • Turns OFF the parking lamp, license plate lamp, side marker lamp, tail lamp and each illumination when the ignition switch is placed OFF.

Front wiper
  • The status just before activation of fail-safe control is maintained until the ignition switch is placed OFF while the front wiper is operating at LO or HI speed.

  • The wiper is operated at LO speed until the ignition switch is placed OFF if the fail-safe control is activated while the front wiper is set in the INT mode and the front wiper motor is operating.

Daytime running light Daytime running light: OFF
Front fog lamp Front fog lamp: OFF
Ignition relay The status just before activation of fail-safe is maintained.
Starter motor Starter relay: OFF

IGNITION RELAY CONTROL

  • The IPDM E/R monitors the voltage at the contact circuit of the ignition relay inside it.

  • The IPDM E/R judges the ignition relay error if the voltage differs between the contact circuit.

Voltage judgementIPDM E/R judgementOperation
Ignition relay contact sideIgnition relay control condition
ON ON Ignition relay ON normal —
OFF OFF Ignition relay OFF normal —
ON OFF Ignition relay ON stuck Detects DTC [B20DD-73: IGN RELAY ON CIRC]
OFF ON Ignition relay OFF stuck Detects DTC [B20DE-72: IGN RELAY OFF CIRC]

FRONT WIPER CONTROL

The IPDM E/R detects the front wiper stop position from the front wiper auto stop signal.

When front wiper auto stop signal is in the condition listed below while the front wiper is operating, the IPDM E/R activates the fail-safe.

Ignition switchFront wiper switchFront wiper auto stop signalFail-safe
ON OFF The signal does not change from the battery voltage for 10 seconds. Stops front wiper power supply for 20 seconds
Except OFF The signal does not change for 10 seconds.

DTC Inspection Priority Chart

PriorityDTC No.CONSULT display
1 U0073-00 Control module comm Bus A Off [NO SUBTYPE INFO]
U1000-01 CAN COMM CIRCUIT [ELECTRICAL MALFUNCTION]
U2004-87 CAN comm err (CCM/ST angle sensor) [MISSING MESSAGE]
U2140-87 CAN comm err (ECM) [MISSING MESSAGE]
U2141-87 CAN comm err (TCM) [MISSING MESSAGE]
U2148-87 CAN comm err (brake control unit) [MISSING MESSAGE]
U214E-87 CAN comm err (combination meter) [MISSING MESSAGE]
U214F-87 CAN comm err (BCM) [MISSING MESSAGE]
U2153-87 CAN comm err (HVAC) [MISSING MESSAGE]
U2159-87 CAN comm err (steering control unit) [MISSING MESSAGE]
U2176-87 CAN comm err (CCM/ST angle sensor) [MISSING MESSAGE]
2 B1200-54 IPDM E/R [NOT CONFIGURED]
B120E-04 IPDM E/R [SYSTEM INTERNAL MALFUNCTN]
B120E-42 IPDM E/R [MEMORY ERROR]
B120E-51 IPDM E/R [SYSTEM INTERNAL MALFUNCTN]
B120E-55 IPDM E/R [NOT CONFIGURED]
3 B12A3-73 Fuel pump Off circuit [CIRC SHORT TO BATTERY]
B12A4-81 Battery current sensor [INVALID SERIAL DATA RECEIVED]
B12A4-92 Battery current sensor [PFM/INCORRECT OPERATN]
B12A4-94 Battery current sensor [UNEXPECTED OPERATION]
B20A1-16 IPDM E/R [CIRC VOLT BELOW THRESHOLD]
B20A1-72 IPDM E/R [ACTUATOR STUCK OPEN]
B20A3-72 ETC RELAY STUCK ON [ACTUATOR STUCK OPEN]
B20B2-72 FRONT WIPER MOTOR CIRCUIT [ACTUATOR STUCK OPEN]
B20DD-73 IGN RELAY ON CIRC [ACTUATOR STUCK CLOSED]
B20DE-72 IGN RELAY OFF CIRC [ACTUATOR STUCK OPEN]
4 B121A-11 FR FOG LAMP LH PWR SPLY CIRC [CIRCUIT SHORT TO GROUND]
B121A-15 FR FOG LAMP LH PWR SPLY CIRC [CIRC SHORT TO BATT OR OPEN]
B1256-11 FR FOG LAMP RH PWR SPLY CIRC [CIRCUIT SHORT TO GROUND]
B1256-15 FR FOG LAMP RH PWR SPLY CIRC [CIRC SHORT TO BATT OR OPEN]
B20A2-87 Headlamp (RH) LIN communication [MISSING MESSAGE]
B20A4-87 Headlamp (LH) LIN communication [MISSING MESSAGE]
B20C7-11 A/C clutch [CIRCUIT SHORT TO GROUND]
B20C7-15 A/C clutch [CIRC SHORT TO BATT OR OPEN]
B20C8-14 Compressor (ECV) [CIRC SHORT TO GRND OR OPEN]
B20D4-11 TAIL LAMP LH PWR SPLY CIRC [CIRCUIT SHORT TO GROUND]
B20D5-11 TAIL LAMP RH PWR SPLY CIRC [CIRCUIT SHORT TO GROUND]
B20E2-96 LED HEADLAMP RH [CMPNENT INTERNAL MLFNCTN]
B20E3-96 LED HEADLAMP LH [CMPNENT INTERNAL MLFNCTN]

DTC Index

  • CRNT: A malfunction is detected now.

  • PASS: A malfunction was detected in the past.

×: Applicable

Self Diagnostic Result
DTC No.CONSULT displayFail-safeReference
B1200-54 IPDM E/R [NOT CONFIGURED] — DTC Description
B120E-04 IPDM E/R [SYSTEM INTERNAL MALFUNCTN] — DTC Description
B120E-42 IPDM E/R [MEMORY ERROR] — DTC Description
B120E-51 IPDM E/R [SYSTEM INTERNAL MALFUNCTN] — DTC Description
B120E-55 IPDM E/R [NOT CONFIGURED] — DTC Description
B121A-11 FR FOG LAMP LH PWR SPLY CIRC [CIRCUIT SHORT TO GROUND] × DTC Description
B121A-15 FR FOG LAMP LH PWR SPLY CIRC [CIRC SHORT TO BATT OR OPEN] — DTC Description
B1256-11 FR FOG LAMP RH PWR SPLY CIRC [CIRCUIT SHORT TO GROUND] × DTC Description
B1256-15 FR FOG LAMP RH PWR SPLY CIRC [CIRC SHORT TO BATT OR OPEN] — DTC Description
B12A3-73 Fuel pump Off circuit [CIRC SHORT TO BATTERY] — DTC Description
B12A4-81 Battery current sensor [INVALID SERIAL DATA RECEIVED] × DTC Description
B12A4-92 Battery current sensor [PFM/INCORRECT OPERATN] × DTC Description
B12A4-94 Battery current sensor [UNEXPECTED OPERATION] ― DTC Description
B20A1-16 IPDM E/R [CIRC VOLT BELOW THRESHOLD] ― DTC Description
B20A1-72 IPDM E/R [ACTUATOR STUCK OPEN] ― DTC Description
B20A2-87 Headlamp (RH) LIN communication [MISSING MESSAGE] × DTC Description
B20A3-72 ETC RELAY STUCK ON [ACTUATOR STUCK OPEN] — DTC Description
B20A4-87 Headlamp (LH) LIN communication [MISSING MESSAGE] × DTC Description
B20B2-72 FRONT WIPER MOTOR CIRCUIT [ACTUATOR STUCK OPEN] — DTC Description
B20C7-11 A/C clutch [CIRCUIT SHORT TO GROUND] × DTC Description
B20C7-15 A/C clutch [CIRC SHORT TO BATT OR OPEN] × DTC Description
B20D4-11 TAIL LAMP LH PWR SPLY CIRC [CIRCUIT SHORT TO GROUND] × DTC Description
B20D5-11 TAIL LAMP RH PWR SPLY CIRC [CIRCUIT SHORT TO GROUND] × DTC Description
B20DD-73 IGN RELAY ON CIRC [ACTUATOR STUCK CLOSED] × DTC Description
B20DE-72 IGN RELAY OFF CIRC [ACTUATOR STUCK OPEN] × DTC Description
B20E2-96 LED HEADLAMP RH [CMPNENT INTERNAL MLFNCTN] × DTC Description
B20E3-96 LED HEADLAMP LH [CMPNENT INTERNAL MLFNCTN] × DTC Description

×: Applicable

Network-DTC
DTC No.CONSULT displayFail-safeReference
U0073-00 Control module comm Bus A Off [NO SUBTYPE INFO] × DTC Description
U1000-01 CAN COMM CIRCUIT [ELECTRICAL MALFUNCTION] — DTC Description
U2004-87 CAN comm err (CCM/ST angle sensor) [MISSING MESSAGE] — DTC Description
U2140-87 CAN comm err (ECM) [MISSING MESSAGE] × DTC Description
U2141-87 CAN comm err (TCM) [MISSING MESSAGE] — DTC Description
U2148-87 CAN comm err (brake control unit) [MISSING MESSAGE] — DTC Description
U214E-87 CAN comm err (combination meter) [MISSING MESSAGE] — DTC Description
U214F-87 CAN comm err (BCM) [MISSING MESSAGE] × DTC Description
U2153-87 CAN comm err (HVAC) [MISSING MESSAGE] — DTC Description
U2159-87 CAN comm err (steering control unit) [MISSING MESSAGE] — DTC Description
U2176-87 CAN comm err (CCM/ST angle sensor) [MISSING MESSAGE] — DTC Description

Removal and Installation. Ipdm E/r (intelligent Power Distribution Module Engine Room) Nissan Pathfinder 5th Gen

Removal and Installation

REMOVAL

Disconnect the negative battery terminal. Refer to Battery Disconnect.

Release the pawls and separate the IPDM E/R (1) from the case.

: Pawl

Disconnect the harness connectors (A) from the IPDM E/R (1).

Remove the IPDM E/R.

INSTALLATION

Installation is in the reverse order of removal.