4013 C106a Wheel Sensor

In this manual: 4013 C106a Wheel Sensor
General Information — 8Engine :: Engine Mechanical — 19Engine Lubrication System - Precautions. Preparation — 1Engine Lubrication System - Lubrication System (System Description). Engine Oil Pressure (Basic Inspection). Service Data and Specifications (SDS) — 1Engine Cooling System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Engine Cooling System - Engine Coolant — 1Engine Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Engine Control System - Ecu Diagnosis Information — 1Ecu Diagnosis Information - Ecm ++ — 1Engine Control System - Basic Inspection — 1Basic Inspection - Diagnosis and Repair Workflow ++ — 1Basic Inspection - Basic Inspection ++ — 1Basic Inspection - Additional Service When Replacing Ecm ++ — 1Basic Inspection - Fuel Pressure Check ++ — 1Basic Inspection - How to Set Srt Code ++ — 1Basic Inspection - How to Erase Permanent Dtc ++ — 1Engine Control System - Dtc/circuit Diagnosis — 1Engine Control System - Symptom Diagnosis — 1Engine Control System - Periodic Maintenance — 1Engine Control System - Removal and Installation — 1Fuel System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Fuel System - Fuel System (Periodic Maintenance). Fuel Level Sensor Unit (Disassembly and Assembly) — 1Exhaust System - Precautions. Preparation — 1Exhaust System - Exhaust System (Periodic Maintenance). Exhaust System (Removal and Installation) — 1Starting System - Precautions. Preparation. Starter Motor (Service Data and Specifications (sds)) — 1Starting System - Diagnosis and Repair Work Flow — 1Starting System - Starting System (Symptom Diagnosis). Starter Motor (Removal and Installation) — 1Accelerator Control System - Precautions. Service Data and Specifications (SDS) — 1Accelerator Control System - Accelerator Pedal Assembly — 1Transmission & Driveline :: Transaxle & Transmission — 21Driveline - System Description — 1Transfer: Ty92b - Ecu Diagnosis Information. Awd Control Unit ++ — 1Driveline - Basic Inspection — 1Driveline - Dtc/circuit Diagnosis — 1Driveline - Symptom Diagnosis — 1Driveline - Removal and Installation — 1Transfer: Ty92b - Unit Removal and Installation. Transfer Assembly ++ — 1Driveline - Unit Disassembly and Assembly — 1Driveline - Basic Inspection — 1Driveline - Removal and Installation — 1Driveline - Unit Disassembly and Assembly — 1Front Axle - Precautions. Preparation — 1Front Axle - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Front Axle - Front Drive Shaft Boot — 1Front Axle - Front Drive Shaft — 1Rear Axle - Precautions. Preparation. Service Data and Specifications (SDS) — 1Rear Axle - Noise, Vibration and Harshness (nvh) Troubleshooting — 1Rear Axle - Rear Drive Shaft — 1Suspension :: Front Suspension — 7Rear Suspension - Precautions. Preparation — 1Rear Suspension - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Rear Suspension - Rear Suspension Assembly — 1Road Wheels & Tires - Precautions — 1Road Wheels & Tires - Preparation. Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Road Wheels & Tires - System — 1Brakes :: Brake System — 9Parking Brake System - Precautions. Preparation — 1Parking Brake System - System — 1Vdc/tcs/abs - Precautions ++ — 1Brake Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Dtc/circuit Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Steering :: Steering System — 9Steering Control System - Precautions — 1Steering Control System - System — 1Steering Control System - Eps Control Unit (Ecu Diagnosis Information. Removal and Installation) — 1Restraints :: Seat Belt — 7Srs Air Bag - Precautions. Preparation — 1Srs Air Bag - Collision Diagnosis — 1Srs Air Bag - Occupant Classification System — 1Srs Air Bag Control System - Precautions — 1Srs Air Bag Control System - System — 1Srs Air Bag Control System - Diagnosis Sensor Unit — 1Srs Air Bag Control System - Inspection and Adjustment — 1Ventilation, Heater & Air Conditioner :: Ventilation System — 6Heater & Air Conditioning System - Precautions — 1Heater & Air Conditioning System - Preparation — 1Heater & Air Conditioning System - Component Parts — 1Heater & Air Conditioning System - Diagnosis and Repair Work Flow — 1Heater & Air Conditioning System - Compressor — 1Heater & Air Conditioning System - Cooler Pipe and Hose — 1Heater & Air Conditioning System - Condenser. Condenser — 1Heater & Air Conditioning System - Heating and Cooling Unit Assembly — 1Heater & Air Conditioning System - Service Data and Specifications (SDS) — 1Heater & Air Conditioning Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1Heater & Air Conditioning Control System - Ecu Diagnosis Information — 1Heater & Air Conditioning Control System - Basic Inspection — 1Heater & Air Conditioning Control System - Dtc/circuit Diagnosis — 1Heater & Air Conditioning Control System - Symptom Diagnosis — 1Heater & Air Conditioning Control System - Removal and Installation — 1Body Interior :: Interior — 8Instrument Panel - Precautions. Preparation. Clip List — 1Instrument Panel - Squeak and Rattle Trouble Diagnoses — 1Instrument Panel - Cluster Lid C — 1Seat - Precautions — 1Seat - Preparation. Clip List — 1Seat - Component Parts — 1Seat - System — 1Seat - Diagnosis and Repair Work Flow — 1Seat - Front Seat — 1Seat - Second Row Seats — 1Seat - Third Row Seats — 1Seat - Front Seat — 1Seat - Second Row Seat — 1Seat - Third Row Seat — 1Automatic Drive Positioner - Precautions. Preparation — 1Automatic Drive Positioner - System — 1Automatic Drive Positioner - Diagnosis and Repair Work Flow — 1Automatic Drive Positioner - Inspection and Adjustment — 1Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock — 38Security Control System - Precautions — 1Security Control System - System — 1Security Control System - Ecm, Bcm, Intelligent Key Unit, Ipdm E/r — 1Security Control System - Vehicle Security System Cannot Be Set — 1Glass & Window System - Precautions. Preparation — 1Glass & Window System - Squeak and Rattle Trouble Diagnoses — 1Power Window Control System - Precautions. Preparation — 1Power Window Control System - Power Supply and Ground Circuit — 1Power Window Control System - Power Window Motor Circuit — 1Power Window Control System - Front Power Window Rh Alone Does Not Operate — 1Power Window Control System - Rear Lh Side Power Window Alone Does Not Operate — 1Power Window Control System - Rear Rh Side Power Window Alone Does Not Operate — 1Roof - Precautions. Preparation — 1Roof - Power Supply and Ground Circuit — 1Roof - Moonroof Switch Assembly — 1Roof - Lin Communication Circuit — 1Roof - Auto Operation Does Not Operate — 1Roof - Anti-Pinch Function Does Not Operate — 1Exterior - Precautions. Preparation. Clip List (Preparation) — 1Exterior - Squeak and Rattle Trouble Diagnoses — 1Exterior - Fender Protector — 1Exterior - Over Fender — 1Exterior - Under Cover — 1Exterior - Roof Side Rail — 1Body Repair - Service Information — 1Service Information - Sheet Metal Work ++ — 1Service Information - Body Welding and Precautions ++ — 1Service Information - Safety and Health ++ — 1Service Information - Repairing Procedures and Precautions ++ — 1Body Repair - Precaution — 1Body Repair - Preparation — 1Body Repair - Removal and Installation — 1Driver Controls :: Mirrors — 8Exterior Lighting System - System Description — 1System Description - Component Parts ++ — 1Exterior Lighting System - Basic Inspection — 1Exterior Lighting System - Dtc/circuit Diagnosis — 1Exterior Lighting System - Symptom Diagnosis — 1Exterior Lighting System - Periodic Maintenance — 1Exterior Lighting System - Removal and Installation — 1Interior Lighting System - Precautions. Preparation — 1Interior Lighting System - Component Parts. Interior Lighting System — 1Interior Lighting System - System — 1Interior Lighting System - Diagnosis and Repair Work Flow — 1Interior Lighting System - Interior Lighting System Symptoms (Symptom Diagnosis). Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Interior Lighting System - Foot Lamp — 1Wiper & Washer - Precautions — 1Wiper & Washer - Preparation. Bcm, Ipdm E/r (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Wiper & Washer - System — 1Wiper & Washer - Diagnosis and Repair Work Flow — 1Defogger - Precautions. Bcm, A/c Auto Amp. (Ecu Diagnosis Information) — 1Defogger - Diagnosis and Repair Work Flow — 1Horn - Precautions — 1Electrical & Power Control :: Power Outlet — 13Body Control System - Precautions. Preparation — 1Body Control System - Component Parts — 1Body Control System - System — 1Body Control System - Diagnosis System (bcm) — 1Body Control System - Bcm — 1Lan System - System Description — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - Removal and Installation — 1Charging System - Precautions. Preparation. Ecm, Ipdm E/r (Ecu Diagnosis Information) — 1Charging System - Diagnosis and Repair Work Flow — 1Charging System - Charging System (Symptom Diagnosis). Generator (Removal and Installation). Service Data and Specifications (SDS) — 1Power Supply, Ground & Circuit Elements - Precautions. Preparation. Service Data and Specifications (SDS) — 1Driver Information & Multimedia :: Meter, Warning Lamp & Indicator — 25Warning Chime System - Application Notice (How to Use This Manual). Precautions — 1Warning Chime System - System — 1Warning Chime System - Diagnosis System (combination Meter) — 1Warning Chime System - Bcm, Combination Meter (Ecu Diagnosis Information). Diagnosis and Repair Work Flow (Basic Inspection) — 1Sonar System - Precautions. Preparation — 1Sonar System - Sonar Control Unit — 1Dtc/circuit Diagnosis - B2720 Corner Sensor [rl] ++ — 1Audio, Visual & Navigation System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Multi Av (av Control Unit) ++ — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Symptom Diagnosis - Multi Av System ++ — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Cruise Control & Driver Assistance :: Cruise Control System — 17Driver Assistance System - System Description — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Driver Assistance System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1System Description - Handling Precaution ++ — 1Driver Assistance System - Ecu Diagnosis Information — 1Driver Assistance System - Basic Inspection — 1Basic Inspection - Distance Sensor Alignment ++ — 1Basic Inspection - Camera Aiming Adjustment ++ — 1Basic Inspection - Action Test ++ — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Laser/radar (distance Sensor) ++ — 1Dtc/circuit Diagnosis - Lane Camera (front Camera Unit) ++ — 1Driver Assistance System - Symptom Diagnosis — 1Driver Assistance System - Removal and Installation — 1Driver Assistance System - System Description — 1System Description - System ++ — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Drive Mode System - Precautions — 1Drive Mode System - Component Parts. Drive Mode System — 1Drive Mode System - System — 1Drive Mode System - Diagnosis and Repair Work Flow — 1Drive Mode System - Drive Mode Select Switch Circuit — 1Maintenance - Precautions. Preparation — 1Maintenance - General Maintenance — 1Maintenance - Periodic Maintenance — 1Maintenance - Recommended Fluids and Lubricants — 1Maintenance - Engine Maintenance — 1Maintenance - Chassis and Body Maintenance — 1Engine Lubrication System - Periodic Maintenance — 1Engine Lubrication System - Removal and Installation — 1Engine Cooling System - System Description — 1Engine Cooling System - Removal and Installation — 1Engine Control System - Vq35dd — 1Fuel System - Removal and Installation — 1Starting System - System Description — 1Starting System - Dtc/circuit Diagnosis — 1Driveline - Transfer: Ty92b — 1Driveline - Rear Propeller Shaft: 3fcj-Cvj — 1Driveline - Rear Final Drive: R145 — 1Front Axle - Periodic Maintenance — 1Front Axle - Removal and Installation — 1Rear Axle - Periodic Maintenance — 1Rear Axle - Removal and Installation — 1Rear Suspension - Removal and Installation — 1Road Wheels & Tires - System Description — 1Road Wheels & Tires - Basic Inspection — 1Road Wheels & Tires - Dtc/circuit Diagnosis — 1Road Wheels & Tires - Symptom Diagnosis — 1Road Wheels & Tires - Periodic Maintenance — 1Road Wheels & Tires - Removal and Installation — 1Parking Brake System - System Description — 1Parking Brake System - Basic Inspection — 1Parking Brake System - Dtc/circuit Diagnosis — 1Parking Brake System - Symptom Diagnosis — 1Parking Brake System - Removal and Installation — 1Brake Control System - Vdc/tcs/abs — 1Brake Control System - Automatic Brake Hold — 1Brake Control System - Automatic Emergency Braking — 1Brake Control System - Rear Automatic Braking — 1Steering Control System - System Description — 1Steering Control System - Basic Inspection — 1Steering Control System - Dtc/circuit Diagnosis — 1Steering Control System - Symptom Diagnosis — 1Srs Air Bag - Removal and Installation — 1Srs Air Bag Control System - System Description — 1Srs Air Bag Control System - Basic Inspection — 1Srs Air Bag Control System - Symptom Diagnosis — 1Heater & Air Conditioning System - Symptom Diagnosis — 1Heater & Air Conditioning System - Periodic Maintenance — 1Heater & Air Conditioning Control System - Automatic Air Conditioning — 1Instrument Panel - Removal and Installation — 1Instrument Panel - Unit Disassembly and Assembly — 1Seat - Ecu Diagnosis Information — 1Seat - Dtc/circuit Diagnosis — 1Seat - Symptom Diagnosis — 1Automatic Drive Positioner - System Description — 1Automatic Drive Positioner - Ecu Diagnosis Information — 1Automatic Drive Positioner - Dtc/circuit Diagnosis — 1Automatic Drive Positioner - Symptom Diagnosis — 1Automatic Drive Positioner - Removal and Installation — 1Security Control System - System Description — 1Security Control System - Basic Inspection — 1Security Control System - Dtc/circuit Diagnosis — 1Security Control System - Symptom Diagnosis — 1Security Control System - Removal and Installation — 1Glass & Window System - Removal and Installation — 1Power Window Control System - System Description — 1Power Window Control System - Ecu Diagnosis Information — 1Power Window Control System - Basic Inspection — 1Power Window Control System - Dtc/circuit Diagnosis — 1Power Window Control System - Symptom Diagnosis — 1Power Window Control System - Removal and Installation — 1Roof - System Description — 1Roof - Ecu Diagnosis Information — 1Roof - Basic Inspection — 1Roof - Dtc/circuit Diagnosis — 1Roof - Symptom Diagnosis — 1Roof - Removal and Installation — 1Exterior - System Description — 1Exterior - Removal and Installation — 1Body Repair - Repair Information — 1Exterior Lighting System - Led Headlamp — 1Interior Lighting System - Dtc/circuit Diagnosis — 1Interior Lighting System - Removal and Installation — 1Wiper & Washer - System Description — 1Wiper & Washer - Dtc/circuit Diagnosis — 1Wiper & Washer - Symptom Diagnosis — 1Wiper & Washer - Removal and Installation — 1Defogger - System Description — 1Defogger - Dtc/circuit Diagnosis — 1Defogger - Symptom Diagnosis — 1Defogger - Removal and Installation — 1Horn - Removal and Installation — 1Body Control System - Basic Inspection — 1Body Control System - Dtc/circuit Diagnosis — 1Body Control System - Symptom Diagnosis — 1Body Control System - Removal and Installation — 1Lan System - Can Fundamental — 1Lan System - Can — 1Lan System - Can Gateway — 1Power Control System - Ipdm E/r — 1Power Control System - Power Distribution System — 1Charging System - System Description — 1Charging System - Dtc/circuit Diagnosis — 1Power Supply, Ground & Circuit Elements - System Description — 1Power Supply, Ground & Circuit Elements - Basic Inspection — 1Power Supply, Ground & Circuit Elements - Removal and Installation — 1Warning Chime System - System Description — 1Warning Chime System - Dtc/circuit Diagnosis — 1Warning Chime System - Symptom Diagnosis — 1Sonar System - System Description — 1Sonar System - Basic Inspection — 1Sonar System - Dtc/circuit Diagnosis — 1Sonar System - Symptom Diagnosis — 1Sonar System - Removal and Installation — 1Audio, Visual & Navigation System - Nissanconnect — 1Audio, Visual & Navigation System - Intelligent Around View Monitor System — 1Audio, Visual & Navigation System - Rear View Monitor System — 1Audio, Visual & Navigation System - Telematics System — 1Driver Assistance System - Adas Control Unit 2 — 1Driver Assistance System - Driver Assistance System — 1Driver Assistance System - Chassis Control — 1Drive Mode System - Removal and Installation — 1Dtc/circuit Diagnosis (C053c Wheel Speed Sensor ... U2141 Can Comm Circuit) — 1Dtc/circuit Diagnosis (P0011 Intake Valve Timing Control ... P0111 Iat Sensor) — 1Dtc/circuit Diagnosis (P0116 Engine Coolant Temperature Sensor ... P025b Fuel Pump Module a) — 1Dtc/circuit Diagnosis (P026b Injection Timing ... P0420 Three Way Catalyst Function) — 1Dtc/circuit Diagnosis (P0441 Evap Control System ... P0524 Engine Oil Pressure) — 1Dtc/circuit Diagnosis (P0532 A/c Refrigerant Pressure Sensor ... P064d Ecm) — 1Dtc/circuit Diagnosis (P06da Engine Oil Pressure Control Solenoid Valve ... P1217 Engine Over Temperature) — 1Dtc/circuit Diagnosis (P1220 Fuel Pump Control Module (fpcm) ... P1574 Ascd Vehicle Speed Sensor) — 1Dtc/circuit Diagnosis (P1575 Brake Switch ... P2101 Electric Throttle Control Function) — 1Dtc/circuit Diagnosis (P2118 Throttle Control Motor ... P34ac Electric Intake Valve Timing Control Actuator) — 1Dtc/circuit Diagnosis (Active Grille Shutter ... High Pressure Fuel Pump) — 1Dtc/circuit Diagnosis (Ignition Signal ... Variable Induction Air System) — 14012 C1040 Emergency Brake — 14013 C106a Wheel Sensor — 14014 C1078-55 Not Configuration — 14015 C10b4-98 Overheat — 14016 B1001 Lap Pre-Tensioner Lh — 14017 B0001 Driver Air Bag Module — 14018 B100e Knee Air Bag Module Rh — 14019 B142x Collision Detection — 1Dtc/circuit Diagnosis (B20c7-11 A/c Clutch ... B24a6-11 in-Vehicle Sensor) — 1Dtc/circuit Diagnosis (B24a6-15 in-Vehicle Sensor ... U2140-87 Can Comm Err (ecm)) — 1Dtc/circuit Diagnosis (C1f00-1c Control Unit ... C1f04-61 Brake Sw/stop Lamp Sw) — 1Dtc/circuit Diagnosis (C1f05-49 Front Camera Unit ... C1f70-87 Ethernet Circuit) — 1
235steps
~1410min
5/5difficulty
Done 0 of 235
  • C106a Wheel Sensor
  • C106b-64 Stop Lamp Sw
  • C106c Pressure Sensor
  • C106d-01 Brake Booster
  • C106e Steering Angle Sensor
  • C106f Steering Angle Sensor
  • C1070-01 Side G Sensor
  • C1071 Decel G Sensor
  • C1073 Vacuum Sensor
  • C1077 Dds Switch

C106a Wheel Sensor Nissan Pathfinder 5th Gen

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C106A-04

Wheel sensor

(Wheel sensor)
1 Diagnosis condition
  • When ignition switch is ON

  • When front left power supply voltage is normal

Signal (terminal) Front left wheel sensor signal
Threshold When a malfunction is detected in front left wheel sensor.
Diagnosis delay time 1 second or less
2 Diagnosis condition
  • When ignition switch is ON

  • When front right power supply voltage is normal

Signal (terminal) Front right wheel sensor signal
Threshold When a malfunction is detected in front right wheel sensor.
Diagnosis delay time 1 second or less
3 Diagnosis condition
  • When ignition switch is ON

  • When rear left power supply voltage is normal

Signal (terminal) Rear left wheel sensor signal
Threshold When a malfunction is detected in rear left wheel sensor.
Diagnosis delay time 1 second or less
4 Diagnosis condition
  • When ignition switch is ON

  • When rear right power supply voltage is normal

Signal (terminal) Rear right wheel sensor signal
Threshold When a malfunction is detected in rear right wheel sensor.
Diagnosis delay time 1 second or less
C106A-55

Wheel sensor

(Wheel sensor)
1 Diagnosis condition
  • When ignition switch is ON

  • When front left power supply voltage is normal

Signal (terminal) Front left wheel sensor signal
Threshold When a malfunction is detected in front left wheel sensor.
Diagnosis delay time 1 second or less
2 Diagnosis condition
  • When ignition switch is ON

  • When front right power supply voltage is normal

Signal (terminal) Front right wheel sensor signal
Threshold When a malfunction is detected in front right wheel sensor.
Diagnosis delay time 1 second or less
3 Diagnosis condition
  • When ignition switch is ON

  • When rear left power supply voltage is normal

Signal (terminal) Rear left wheel sensor signal
Threshold When a malfunction is detected in rear left wheel sensor.
Diagnosis delay time 1 second or less
4 Diagnosis condition
  • When ignition switch is ON

  • When rear right power supply voltage is normal

Signal (terminal) Rear right wheel sensor signal
Threshold When a malfunction is detected in rear right wheel sensor.
Diagnosis delay time 1 second or less
C106A-62

Wheel sensor

(Wheel sensor)
1 Diagnosis condition
  • When ignition switch is ON

  • When front left power supply voltage is normal

Signal (terminal) Front left wheel sensor signal
Threshold When a malfunction is detected in front left wheel sensor.
Diagnosis delay time 1 second or less
2 Diagnosis condition
  • When ignition switch is ON

  • When front right power supply voltage is normal

Signal (terminal) Front right wheel sensor signal
Threshold When a malfunction is detected in front right wheel sensor.
Diagnosis delay time 1 second or less
3 Diagnosis condition
  • When ignition switch is ON

  • When rear left power supply voltage is normal

Signal (terminal) Rear left wheel sensor signal
Threshold When a malfunction is detected in rear left wheel sensor.
Diagnosis delay time 1 second or less
4 Diagnosis condition
  • When ignition switch is ON

  • When rear right power supply voltage is normal

Signal (terminal) Rear right wheel sensor signal
Threshold When a malfunction is detected in rear right wheel sensor.
Diagnosis delay time 1 second or less
C106A-64

Wheel sensor

(Wheel sensor)
1 Diagnosis condition
  • When ignition switch is ON

  • When front left power supply voltage is normal

Signal (terminal) Front left wheel sensor signal
Threshold When a malfunction is detected in front left wheel sensor.
Diagnosis delay time 1 second or less
2 Diagnosis condition
  • When ignition switch is ON

  • When front right power supply voltage is normal

Signal (terminal) Front right wheel sensor signal
Threshold When a malfunction is detected in front right wheel sensor.
Diagnosis delay time 1 second or less
3 Diagnosis condition
  • When ignition switch is ON

  • When rear left power supply voltage is normal

Signal (terminal) Rear left wheel sensor signal
Threshold When a malfunction is detected in rear left wheel sensor.
Diagnosis delay time 1 second or less
4 Diagnosis condition
  • When ignition switch is ON

  • When rear right power supply voltage is normal

Signal (terminal) Rear right wheel sensor signal
Threshold When a malfunction is detected in rear right wheel sensor.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

PAST DTCCRNT DTC
  • Harness or connector

  • Front left wheel sensor

  • Front left sensor rotor

  • Front left tire size

  • Front right wheel sensor

  • Front right sensor rotor

  • Front right tire size

  • Rear left wheel sensor

  • Rear left sensor rotor

  • Rear left tire size

  • Rear right wheel sensor

  • Rear right sensor rotor

  • Rear right tire size

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12 V battery

  • Nissan Pathfinder Vehicle was not driven after previous repair

  • Harness or connector

  • Front left wheel sensor

  • Front left sensor rotor

  • Front left tire size

  • Front right wheel sensor

  • Front right sensor rotor

  • Front right tire size

  • Rear left wheel sensor

  • Rear left sensor rotor

  • Rear left tire size

  • Rear right wheel sensor

  • Rear right sensor rotor

  • Rear right tire size

  • ABS actuator and electric unit (control unit)

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12 V battery

FAIL-SAFE

The following functions are suspended:

  • VDC function

  • TCS function

  • ABS function

  • EBD function

  • Active brake limited slip (ABLS) function

  • Brake assist function

  • Brake force distribution function

  • Hill start assist function

  • Electric parking brake function

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Start the engine.

  2. Drive the Nissan Pathfinder vehicle at approximately 50 km/h or more for approximately 2 minutes.

  3. Stop the vehicle.

  4. Ignition switch OFF (Auto ACC function OFF).

  5. Start the engine.

  6. Perform self-diagnosis for “ABS”.

Is DTC “C106A” detected?

YES>>

“CRNT” is displayed: Refer to Diagnosis Procedure.

YES>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End

Diagnosis Procedure

CHECK TIRE

Check the tire air pressure, wear and size. Refer to Tire Air Pressure.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Adjust air pressure or replace tire and GO TO 2.

CHECK DATA MONITOR (1)

CONSULT

  1. Erase self-diagnosis result for “ABS”.

  2. Ignition switch OFF (Auto ACC function OFF) → ON → OFF (Auto ACC function OFF).

  3. Start the engine.

  4. Select “ABS” and “Data Monitor”, check "FR LH wheel speed", "FR RH wheel speed", "RR LH wheel speed", and "RR RH wheel speed".

  5. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 3.

NO>>

GO TO 4.

PERFORM SELF-DIAGNOSIS (1)

CONSULT

  1. Stop the Nissan Pathfinder vehicle.

  2. Ignition switch OFF (Auto ACC function OFF).

  3. Start the engine.

  4. Select “Self Diagnostic result” mode of “ABS”.

Is DTC “C106A” detected?

YES>>

GO TO 4.

NO>>

Inspection End

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT

Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link.

CHECK WHEEL SENSOR AND SENSOR ROTOR

  1. Disconnect 12 V battery negative terminal.

  2. Disconnect wheel sensor harness connector.

  3. Remove dust and foreign matter adhered to the wheel sensor and sensor rotor with a vacuum dust collector through the front left wheel sensor mounting hole.

    • Front: Refer to Exploded View.

    • Rear: Refer to Exploded View.

>>

GO TO 6.

CHECK WHEEL SENSOR

Check the wheel sensor for damage.

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

GO TO 7.

CHECK WHEEL SENSOR OUTPUT SIGNAL

  1. Disconnect ABS actuator and electric unit (control unit) harness connector.

  2. Disconnect wheel sensor harness connector.

  3. Connect ABS active wheel sensor tester (SST: NI-45741-A) to wheel sensor using appropriate adapter.

  4. Turn the ABS active wheel sensor tester power switch ON.

  5. Spin the wheel of the Nissan Pathfinder vehicle by hand and observe the red SENSOR indicator on the ABS active wheel sensor tester. The red SENSOR indicator should flash ON and OFF to indicate an output signal.

Does the ABS active wheel sensor tester detect a signal?

YES>>

Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.

NO>>

GO TO 8.

REPLACE WHEEL SENSOR (1)

CONSULT

  1. Replace the wheel sensor.

    • Front: Refer to Removal and Installation.

    • Rear: Refer to Removal and Installation.

  2. Connect 12 V battery negative terminal.

  3. Erase self-diagnosis result for “ABS”.

  4. Ignition switch OFF (Auto ACC function OFF) → ON → OFF (Auto ACC function OFF).

  5. Start the engine.

  6. Select “ABS” and “Data Monitor”, check "FR LH wheel speed", "FR RH wheel speed", "RR LH wheel speed", and "RR RH wheel speed".

  7. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 9.

NO>>

GO TO 21.

PERFORM SELF-DIAGNOSIS (2)

CONSULT

  1. Stop the Nissan Pathfinder vehicle.

  2. Ignition switch OFF (Auto ACC function OFF).

  3. Start the engine.

  4. Select “Self Diagnostic result” mode of “ABS”.

Is DTC “C106A” detected?

YES>>

GO TO 10.

NO>>

Inspection End

CHECK CONNECTOR

  1. Disconnect 12 V battery negative terminal.

  2. Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.

  3. Check the wheel sensor harness connector for disconnection or looseness.

Is the inspection result normal?

YES>>

GO TO 13.

NO>>

Repair / replace harness or connector, securely lock the connector. GO TO 11.

CHECK DATA MONITOR (2)

CONSULT

  1. Connect 12 V battery negative terminal.

  2. Erase self-diagnosis result for “ABS”.

  3. Ignition switch OFF (Auto ACC function OFF) → ON → OFF (Auto ACC function OFF).

  4. Start the engine.

  5. Select “ABS” and “Data Monitor”, check "FR LH wheel speed", "FR RH wheel speed", "RR LH wheel speed", and "RR RH wheel speed".

  6. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 12.

NO>>

GO TO 13.

PERFORM SELF-DIAGNOSIS (3)

CONSULT

  1. Stop the Nissan Pathfinder vehicle.

  2. Ignition switch OFF (Auto ACC function OFF).

  3. Start the engine.

  4. Select “Self Diagnostic result” mode of “ABS”.

Is DTC “C106A” detected?

YES>>

GO TO 13.

NO>>

Inspection End

CHECK TERMINAL

  1. Disconnect 12 V battery negative terminal.

  2. Disconnect ABS actuator and electric unit (control unit) harness connector and then check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.

  3. Disconnect wheel sensor harness connector and check wheel sensor terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

GO TO 16.

NO>>

Repair / replace harness, connector, or terminal. GO TO 14.

CHECK DATA MONITOR (3)

CONSULT

  1. Connect ABS actuator and electric unit (control unit) harness connector.

  2. Connect wheel sensor harness connector.

  3. Connect 12 V battery negative terminal.

  4. Erase self-diagnosis result for “ABS”.

  5. Ignition switch OFF (Auto ACC function OFF) → ON → OFF (Auto ACC function OFF).

  6. Start the engine.

  7. Select “ABS” and “Data Monitor”, check "FR LH wheel speed", "FR RH wheel speed", "RR LH wheel speed", and "RR RH wheel speed".

  8. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 15.

NO>>

GO TO 16.

PERFORM SELF-DIAGNOSIS (4)

CONSULT

  1. Stop the Nissan Pathfinder vehicle.

  2. Ignition switch OFF (Auto ACC function OFF).

  3. Start the engine.

  4. Select “Self Diagnostic result” mode of “ABS”.

Is DTC “C106A” detected?

YES>>

GO TO 16.

NO>>

Inspection End.

CHECK WHEEL SENSOR HARNESS

  1. Disconnect 12 V battery negative terminal.

  2. Disconnect ABS actuator and electric unit (control unit) harness connector.

  3. Disconnect wheel sensor harness connector.

  4. Check the continuity between ABS actuator and electric unit (control unit) harness connector and front left wheel sensor harness connector. (Check continuity while turning steering wheel left and right, or while moving center harness in wheel housing.)

    • Measurement connector and terminal for power supply circuit

      ABS actuator and electric unit (control unit)Wheel sensorContinuity
      ConnectorTerminalConnectorTerminal
      E125 7 E18 (Front left) 1 Yes
      26 E43 (Front right)
      39 B5 (Rear left)
      22 B119 (Rear right)
    • Measurement connector and terminal for signal circuit

      ABS actuator and electric unit (control unit)Wheel sensorContinuity
      ConnectorTerminalConnectorTerminal
      E125 24 E18 (Front left) 2 Yes
      21 E43 (Front right)
      23 B59 (Rear left)
      37 B67 (Rear right)
  5. Check the continuity between ABS actuator and electric unit (control unit) harness connector and the ground.

    ABS actuator and electric unit (control unit)(–)Continuity
    ConnectorTerminal
    E125 24, 7 Ground No
    21, 26
    39, 23
    22, 37

Is the inspection result normal?

YES>>

GO TO 17.

NO>>

Repair / replace harness or connector. GO TO 17.

CHECK DATA MONITOR (4)

CONSULT

  1. Connect ABS actuator and electric unit (control unit) harness connector.

  2. Connect wheel sensor harness connector.

  3. Connect 12 V battery negative terminal.

  4. Erase self-diagnosis result for “ABS”.

  5. Ignition switch OFF (Auto ACC function OFF) → ON → OFF (Auto ACC function OFF).

  6. Start the engine.

  7. Select “ABS” and “Data Monitor”, check "FR LH wheel speed", "FR RH wheel speed", "RR LH wheel speed", and "RR RH wheel speed".

  8. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 18.

NO>>

GO TO 19.

PERFORM SELF-DIAGNOSIS (5)

CONSULT

  1. Stop the Nissan Pathfinder vehicle.

  2. Ignition switch OFF (Auto ACC function OFF).

  3. Start the engine.

  4. Select “Self Diagnostic result” mode of “ABS”.

Is DTC “C106A” detected?

YES>>

GO TO 20.

NO>>

Inspection End.

REPLACE WHEEL SENSOR (2)

CONSULT

  1. Disconnect 12 V battery negative terminal.

  2. Replace the front left wheel sensor.

    • Front: Refer to Removal and Installation.

    • Rear: Refer to Removal and Installation.

  3. Connect 12 V battery negative terminal.

  4. Erase self-diagnosis result for “ABS”.

  5. Ignition switch OFF (Auto ACC function OFF) → ON → OFF (Auto ACC function OFF).

  6. Start the engine.

  7. Select “ABS” and “Data Monitor”, check "FR LH wheel speed", "FR RH wheel speed", "RR LH wheel speed", and "RR RH wheel speed".

  8. Read a value (wheel speed) of all wheel sensor.

YES>>

GO TO 20.

NO>>

GO TO 21.

PERFORM SELF-DIAGNOSIS (6)

CONSULT

  1. Stop the Nissan Pathfinder vehicle.

  2. Ignition switch OFF (Auto ACC function OFF).

  3. Start the engine.

  4. Select “Self Diagnostic result” mode of “ABS”.

Is DTC “C106A” detected?

YES>>

GO TO 21.

NO>>

Inspection End

REPLACE SENSOR ROTOR

CONSULT

  1. Disconnect 12 V battery negative terminal.

  2. Replace the front left sensor rotor.

    • Front

      • 2WD models: Refer to Removal and Installation.

      • 4WD models: Refer to Removal and Installation.

    • Rear

      • 2WD models: Refer to Removal and Installation.

      • 4WD models: Refer to Removal and Installation.

  3. Connect 12 V battery negative terminal.

  4. Erase self-diagnosis result for “ABS”.

  5. Ignition switch OFF (Auto ACC function OFF) → ON → OFF (Auto ACC function OFF).

  6. Start the engine.

  7. Drive the Nissan Pathfinder vehicle at approximately 50 km/h or more for approximately 2 minutes.

  8. Stop the Nissan Pathfinder vehicle.

  9. Ignition switch OFF (Auto ACC function OFF).

  10. Start the engine.

  11. Select “Self Diagnostic result” mode of “ABS”.

Is DTC “C106A” detected?

YES>>

Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.

NO>>

Inspection End.

C106b-64 Stop Lamp Sw Nissan Pathfinder SUV

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C106B-64

Stop lamp SW

(Stop lamp switch)
Diagnosis condition
  • When ignition switch is ON.

  • When the power supply voltage is normal.

Signal (terminal) CAN communication signal
Threshold When stop lamp switch signal is not input when brake pedal operates.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

PAST DTCCRNT DTC
  • Harness or connector

  • CAN communication line

  • Stop lamp switch signal circuit

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12 V battery

  • Harness or connector

  • CAN communication line

  • Stop lamp switch

  • BCM

  • ABS actuator and electric unit (control unit)

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12 V battery

FAIL-SAFE

The following functions are suspended:

  • VDC function

  • TCS function

  • Active brake limited slip (ABLS) function

  • Brake assist function

  • Brake force distribution function

  • Hill start assist function

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF), and wait 10 seconds or more.

  2. Start the engine.

  3. Wait 1 minute or more.

  4. Depress brake pedal by 3.94 in (100 mm) or more, and maintain at that position for a minimum of 1 minute or more.

  5. Release brake pedal, and wait 1 minute or more.

  6. Ignition switch OFF (Auto ACC function OFF).

  7. Start the engine.

  8. Perform self-diagnosis for “ABS”.

Is DTC “C106B-64” detected?

YES>>

“CRNT” is displayed: Refer to Diagnosis Procedure.

YES>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End

Diagnosis Procedure

CHECK BCM SYSTEM

CONSULT

Perform self-diagnosis for “BCM”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 2.

CHECK BRAKE PEDAL AND CHECK STOP LAMP SWITCH GAP ADJUSTMENT

Check the brake pedal and check stop lamp switch gap adjustment.

  • Brake pedal height: Refer to Inspection.

  • Brake pedal assembly: Refer to Adjustment.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Adjust the brake pedal height or replace brake pedal assembly.

  • Adjust the brake pedal: Refer to Adjustment.

  • Replace the brake pedal: Refer to Removal and Installation.

CHECK CONNECTOR AND TERMINAL

  1. Disconnect 12V battery negative terminal.

  2. Disconnect BCM harness connector.

  3. Disconnect ABS actuator and electric unit (control unit) harness connector.

  4. Check the connector for disconnection or looseness.

  5. Check the terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair / replace harness, connector, or terminal, securely lock the connector. GO TO 3.

PERFORM SELF-DIAGNOSIS

CONSULT

  1. Connect BCM harness connector.

  2. Connect ABS actuator and electric unit (control unit) harness connector.

  3. Connect 12V battery negative terminal.

  4. Erase self-diagnosis result for “ABS”.

  5. Ignition switch OFF (Auto ACC function OFF).

  6. Start the engine.

  7. Perform self-diagnosis for “ABS”.

Is DTC “C106B-64” detected?

YES>>

Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.

NO>>

Inspection End

C106c Pressure Sensor Nissan Pathfinder Fifth generation

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C106C-01

Pressure sensor

(Pressure sensor)
Diagnosis condition
  • When ignition switch is ON.

  • When the power supply voltage is normal.

Signal (terminal) Pressure sensor signal
Threshold When a malfunction is detected in pressure sensor.
Diagnosis delay time 1 second or less
C106C-02

Pressure sensor

(Pressure sensor)
Diagnosis condition
  • When ignition switch is ON.

  • When the power supply voltage is normal.

Signal (terminal) Pressure sensor signal
Threshold When a malfunction is detected in pressure sensor.
Diagnosis delay time 1 second or less
C106C-16

Pressure sensor

(Pressure sensor)
Diagnosis condition
  • When ignition switch is ON.

  • When the power supply voltage is normal.

Signal (terminal) Pressure sensor signal
Threshold When a malfunction is detected in pressure sensor.
Diagnosis delay time 1 second or less
C106C-17

Pressure sensor

(Pressure sensor)
Diagnosis condition
  • When ignition switch is ON.

  • When the power supply voltage is normal.

Signal (terminal) Pressure sensor signal
Threshold When a malfunction is detected in pressure sensor.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

PAST DTCCRNT DTC
  • Harness or connector

  • Air inclusion in the brake piping

  • Stop lamp switch system

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12 V battery

  • Harness or connector

  • Air inclusion in the brake piping

  • Stop lamp switch system

  • Brake system

  • ABS actuator and electric unit (control unit)

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12 V battery

FAIL-SAFE

The following functions are suspended:

  • VDC function

  • TCS function

  • Active brake limited slip (ABLS) function

  • Brake assist function

  • Brake force distribution function

  • Hill start assist function

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF).

  2. Start the engine.

  3. Perform self-diagnosis for “ABS”.

Is DTC “C106C” detected?

YES>>

“CRNT” is displayed: Refer to Diagnosis Procedure.

YES>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End

Diagnosis Procedure

STOP LAMP SWITCH SYSTEM

Check the stop lamp switch system. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace stop lamp switch system.

CHECK BRAKE FLUID LEAKAGE

Check the brake fluid leakage. Refer to Inspection.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace brake fluid leakage part.

CHECK BRAKE PIPING

Check the brake piping.

  • Front: Refer to Inspection.

  • Rear: Refer to Inspection.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace brake piping.

  • Front: Refer to Removal and Installation.

  • Rear: Refer to Removal and Installation.

CHECK BRAKE PEDAL AND CHECK STOP LAMP GAP ADJUSTMENT

Check the brake pedal and check stop lamp gap adjustment.

  • Brake pedal height: Refer to Inspection.

  • Brake pedal assembly: Refer to Removal and Installation.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Adjust the brake pedal height or replace brake pedal assembly.

  • Adjust the brake pedal: Refer to Inspection.

  • Replace the brake pedal: Refer to Removal and Installation.

CHECK BRAKE MASTER CYLINDER

Check the brake master cylinder. Refer to Inspection.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace brake master cylinder. Refer to Removal and Installation.

CHECK BRAKE BOOSTER

Check the brake booster. Refer to Inspection.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair or replace brake booster. Refer to Removal and Installation.

CHECK VACUUM PIPING AND CHECK VALVE

Check the vacuum piping and check valve. Refer to Inspection.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair or replace vacuum piping. Refer to Removal and Installation.

CHECK FRONT DISC BRAKE

Check the front disc brake. Refer to Removal and Installation.

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Repair or replace front disc brake. Refer to Removal and Installation.

CHECK REAR DISC BRAKE

Check the rear disc brake. Refer to Removal and Installation.

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair or replace rear disc brake. Refer to Removal and Installation.

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT

Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 11.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link.

PERFORM SELF-DIAGNOSIS

CONSULT

  1. Erase self-diagnosis result for “ABS”.

  2. Ignition switch OFF (Auto ACC function OFF).

  3. Start the engine.

  4. Start the engine and drive the Nissan Pathfinder vehicle for a short period of time.

  5. Stop the Nissan Pathfinder vehicle.

  6. Perform self-diagnosis for “ABS”.

Is DTC “C106C-01” detected?

YES>>

Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.

NO>>

Check the ABS actuator and electric unit (control unit) harness connector and terminal for damage, looseness and disconnection. Repair / replace harness, connector, or terminal.

C106d-01 Brake Booster Nissan Pathfinder 5th Gen

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C106D-01

Brake booster

(Brake booster)
Diagnosis condition
  • When ignition switch is ON.

  • When the power supply voltage is normal.

Signal (terminal) Brake vacuum sensor signal
Threshold When brake booster vacuum is approx. 0 kPa (0 mmHg) during engine running.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

PAST DTCCRNT DTC
  • Harness or connector

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12 V battery

  • Harness or connector

  • Brake vacuum sensor

  • ABS actuator and electric unit (control unit)

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12 V battery

FAIL-SAFE

The following functions are suspended:

  • VDC function

  • TCS function

  • Active brake limited slip (ABLS) function

  • Brake assist function

  • Brake force distribution function

  • Hill start assist function

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF).

  2. Start the engine.

  3. Perform self-diagnosis for “ABS”.

Is DTC “C106D-01” detected?

YES>>

“CRNT” is displayed: Refer to Diagnosis Procedure.

YES>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End

Diagnosis Procedure

CHECK CONNECTOR

  1. Disconnect 12V battery negative terminal.

  2. Check the brake vacuum sensor harness connector for disconnection or looseness.

  3. Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair / replace harness or connector. GO TO 2.

CHECK BRAKE BOOSTER

Check the brake booster. Refer to Inspection.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Replace the brake booster. Refer to Removal and Installation.

CHECK VACUUM PIPING

Check the vacuum piping. Refer to Inspection.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Replace the vacuum piping. Refer to Removal and Installation.

CHECK TERMINAL

  1. Disconnect 12V battery negative terminal.

  2. Disconnect brake vacuum sensor harness connector.

  3. Check the brake vacuum sensor terminals for damage or loose connection with harness connector.

  4. Disconnect ABS actuator and electric unit (control unit) harness connector.

  5. Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness, connector, or terminal.

CHECK BRAKE VACUUM SENSOR CIRCUIT

  1. Disconnect brake vacuum sensor harness connector.

  2. Disconnect ABS actuator and electric unit (control unit) harness connector.

  3. Check the continuity between brake vacuum sensor harness connector and ABS actuator and electric unit (control unit) harness connector.

    Brake vacuum sensorABS actuator and electric unit (control unit)Continuity
    ConnectorTerminalConnectorTerminal
    E167 1 E125 45 Yes
    2 28
    3 17
  4. Check the continuity between brake vacuum sensor harness connector and ground.

    Brake vacuum sensor—Continuity
    ConnectorTerminal
    E167 1 Ground No
    2
    3

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair / replace harness or connector.

REPLACE BRAKE VACUUM SENSOR

CONSULT

  1. Connect ABS actuator and electric unit (control unit) harness connector.

  2. Replace the brake vacuum sensor.

  3. Connect 12V battery negative terminal.

  4. Erase self-diagnosis result for “ABS”.

  5. Ignition switch OFF (Auto ACC function OFF) → ON → OFF (Auto ACC function OFF).

  6. Start engine.

  7. Perform self-diagnosis for “ABS”.

Is DTC “C106D-01” detected?

YES>>

Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.

NO>>

Inspection End

C106e Steering Angle Sensor Nissan Pathfinder

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C106E-54

Steering angle sensor

(Steering angle sensor)
Diagnosis condition
  • When ignition switch is ON.

  • When the power supply voltage is normal.

Signal (terminal) —
Threshold When neutral position adjustment of steering angle sensor is not complete.
Diagnosis delay time 2 seconds or less
C106E-55

Steering angle sensor

(Steering angle sensor)
Diagnosis condition
  • When ignition switch is ON.

  • When the power supply voltage is normal.

Signal (terminal) —
Threshold When neutral position adjustment of steering angle sensor is not complete.
Diagnosis delay time 2 seconds or less
C106E-64

Steering angle sensor

(Steering angle sensor)
Diagnosis condition
  • When ignition switch is ON.

  • When the power supply voltage is normal.

Signal (terminal) —
Threshold When a malfunction is detected in steering angle sensor..
Diagnosis delay time 2 seconds or less

POSSIBLE CAUSE

PAST DTCCRNT DTC
Incomplete neutral position adjustment of steering angle sensor
  • Incomplete neutral position adjustment of steering angle sensor

  • Steering angle sensor

  • ABS actuator and electric unit (control unit)

FAIL-SAFE

The following functions are suspended:

  • VDC function

  • TCS function

  • Active brake limited slip (ABLS) function

  • Brake assist function

  • Brake force distribution function

  • Hill start assist function

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF).

  2. Start the engine.

  3. Perform self-diagnosis for “ABS”.

Is DTC “C106E” detected?

YES>>

“CRNT” is displayed: Refer to Diagnosis Procedure.

YES>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End

Diagnosis Procedure

ADJUST THE NEUTRAL POSITION OF STEERING ANGLE SENSOR

Perform neutral position adjustment of steering angle sensor. Refer to Work Procedure.

>>

GO TO 2.

PERFORM SELF-DIAGNOSIS

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF).

  2. Start the engine.

  3. Perform self-diagnosis for “ABS”.

Is DTC “C106E-54” detected?

YES>>

GO TO 3.

NO>>

Inspection End

CHECK STEERING ANGLE SENSOR SYSTEM

Check the steering angle sensor system.

  • C106E Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair / replace harness, connector, or terminal.

CHECK DATA MONITOR

CONSULT

  1. Select “ABS”, “Data Monitor” and “Steering angle” according to this order.

  2. Check that the indication changes with the steering angle when the steering wheel is turned left/right from the neutral position. Refer to Reference Value.

Is the inspection result normal?

YES>>

Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.

NO>>

Replace the steering angle sensor. Refer to Removal and Installation.

C106f Steering Angle Sensor Nissan Pathfinder Fifth generation

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C106F-54

Steering angle sensor

(Steering angle sensor)
Diagnosis condition
  • When ignition switch is ON.

  • When the power supply voltage is normal.

Signal (terminal) CAN communication signal
Threshold When a malfunction is detected in steering angle sensor.
Diagnosis delay time 2 seconds or less

POSSIBLE CAUSE

PAST DTCCRNT DTC
  • Improper installation of steering angle sensor

  • Harness or connector

  • CAN communication line

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12 V battery

  • Improper installation of steering angle sensor

  • Harness or connector

  • CAN communication line

  • Wheel alignment

  • Steering angle sensor (Models without FEB)

  • ABS actuator and electric unit (control unit)

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12 V battery

FAIL-SAFE

The following functions are suspended:

  • VDC function

  • TCS function

  • Active brake limited slip (ABLS) function

  • Brake assist function

  • Brake force distribution function

  • Hill start assist function

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF).

  2. Start the engine.

  3. Perform self-diagnosis for “ABS”.

Is DTC “C106F-54” detected?

YES>>

“CRNT” is displayed: Refer to Diagnosis Procedure.

YES>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End

Diagnosis Procedure

ADJUST THE NEUTRAL POSITION OF STEERING ANGLE SENSOR

CONSULT

Perform neutral position adjustment of steering angle sensor. Refer to Work Procedure.

>>

GO TO 2.

PERFORM SELF-DIAGNOSIS (1)

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF).

  2. Start the engine.

  3. Perform self-diagnosis for “ABS”.

Is DTC “C106F-54” detected?

YES>>

“CRNT” is displayed: GO TO 3.

YES>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO>>

Inspection End

CHECK CONNECTOR

  1. Disconnect 12V battery negative terminal.

  2. Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.

  3. Check the steering angle sensor harness connector for disconnection or looseness.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair / replace harness or connector, securely lock the connector. GO TO 4.

PERFORM SELF-DIAGNOSIS (2)

CONSULT

  1. Connect 12V battery negative terminal.

  2. Start the engine.

  3. Perform self-diagnosis for “ABS”.

Is DTC “C106F-54” detected?

YES>>

“CRNT” is displayed: GO TO 5.

YES>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO>>

Inspection End

STEERING ANGLE SENSOR POWER SUPPLY

  1. Disconnect 12V battery negative terminal.

  2. Disconnect steering angle sensor harness connector.

  3. Connect 12V battery negative terminal.

  4. Check the voltage between steering angle sensor harness connector and ground.

    +―Voltage
    Steering angle sensor
    ConnectorTerminal
    M54 8 Ground Approx. 0 V
  5. Ignition switch ON.

  6. Check the voltage between steering angle sensor harness connector and ground.

    +―Voltage
    Steering angle sensor
    ConnectorTerminal
    M54 8 Ground Approx.10 - 16 V

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

GO TO 6.

STEERING ANGLE SENSOR POWER SUPPLY CIRCUIT

  1. Disconnect 12V battery negative terminal.

  2. Check the 5A fuse (#5).

  3. Disconnect fuse block (J/B) harness connector.

  4. Check the continuity between steering angle sensor harness connector and fuse block (J/B) harness connector.

    Steering angle sensorFuse block (J/B)Continuity
    ConnectorTerminalConnectorTerminal
    M54 8 M161 6F Yes
  5. Check the continuity between steering angle sensor harness connector and ground.

    Steering angle sensor—Continuity
    ConnectorTerminal
    M54 8 Ground No
YES>>

Perform trouble diagnosis for ignition power supply.

NO>>

Repair / replace harness, connector, or fuse.

STEERING ANGLE SENSOR GROUND CIRCUIT

Check the continuity between steering angle sensor harness connector and ground.

Steering angle sensor—Continuity
ConnectorTerminal
M54 5 Ground Yes

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair / replace harness or connector.

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT

Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link.

CHECK TERMINAL

  1. Disconnect 12V battery negative terminal.

  2. Check the steering angle sensor terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair / replace harness, connector, or terminal.

CHECK CAN COMMUNICATION LINE

  1. Connect steering angle sensor harness connector.

  2. Connect fuse block (J/B) harness connector.

  3. Connect 12V battery negative terminal.

  4. Check the CAN communication line. Refer to Trouble Diagnosis Flow Chart.

Is the inspection result normal?

YES>>

GO TO 11.

NO>>

Repair / replace harness or connector.

CHECK DATA MONITOR

CONSULT

  1. Select "ABS", "Data Monitor" and "Steering angle" according to this order.

  2. Check that the indication changes with steering angle when the steering wheel is turned left/right from the neutral position. Refer to Reference Value.

Is the inspection result normal?

YES>>

Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.

NO>>

Replace the steering angle sensor. Refer to Removal and Installation.

C1070-01 Side G Sensor Nissan Pathfinder Fifth generation

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C1070–01

Side G sensor

(Side G sensor)
Diagnosis condition
  • When ignition switch is ON.

  • When the power supply voltage is normal.

Signal (terminal) Side G sensor signal
Threshold When a malfunction is detected in side G sensor signal.
Diagnosis delay time 1 second or less
C1070–54

Side G sensor

(Side G sensor)
Diagnosis condition
  • When ignition switch is ON.

  • When the power supply voltage is normal.

Signal (terminal) Side G sensor signal
Threshold When calibration of side G sensor is not complete.
Diagnosis delay time 1 second or less
C1070–64

Side G sensor

(Side G sensor)
Diagnosis condition
  • When ignition switch is ON.

  • When the power supply voltage is normal.

Signal (terminal) Side G sensor signal
Threshold When a malfunction is detected in side G sensor signal.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

PAST DTCCRNT DTC
  • Change in Nissan Pathfinder vehicle posture (e.g. different tire sizes on front and rear, overloaded)

  • ABS actuator and electric unit (control unit) install angle is improper

  • Harness or connector

  • ABS actuator and electric unit (control unit)

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12 V battery

  • Change in Nissan Pathfinder vehicle posture (e.g. different tire sizes on front and rear, overloaded)

  • ABS actuator and electric unit (control unit) install angle is improper

  • Harness or connector

  • ABS actuator and electric unit (control unit)

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12 V battery

FAIL-SAFE

The following functions are suspended:

  • VDC function

  • TCS function

  • Active brake limited slip (ABLS) function

  • Brake assist function

  • Brake force distribution function

  • Hill start assist function

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF).

  2. Start the engine.

  3. Perform self-diagnosis for “ABS”.

Is DTC “C1070” detected?

YES>>

“CRNT” is displayed: Refer to Diagnosis Procedure.

YES>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End

Diagnosis Procedure

CHECK SELF-DIAGNOSIS RESULTS

CONSULT

Replace the ABS actuator and electric unit (control unit) even if other DTCs are displayed along with “C1070-01” in self-diagnosis for “ABS”.

>>

Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.

C1071 Decel G Sensor Nissan Pathfinder 2026

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C1071–54

Decel G sensor

(Decel G sensor)
Diagnosis condition
  • When ignition switch is ON.

  • When the power supply voltage is normal.

Signal (terminal) -
Threshold When calibration of decel G sensor is not complete.
Diagnosis delay time 2 seconds or less
C1071–61

Decel G sensor

(Decel G sensor)
Diagnosis condition
  • When ignition switch is ON.

  • When the power supply voltage is normal.

Signal (terminal) -
Threshold When a malfunction is detected in decel G sensor signal.
Diagnosis delay time 2 seconds or less
C1071–64

Decel G sensor

(Decel G sensor)
Diagnosis condition
  • When ignition switch is ON.

  • When the power supply voltage is normal.

Signal (terminal) -
Threshold When a malfunction is detected in decel G sensor signal..
Diagnosis delay time 2 seconds or less

POSSIBLE CAUSE

PAST DTCCRNT DTC
Incomplete calibration of decel G sensor
  • Incomplete calibration of decel G sensor

  • ABS actuator and electric unit (control unit)

FAIL-SAFE

The following functions are suspended:

  • VDC function

  • TCS function

  • Active brake limited slip (ABLS) function

  • Brake assist function

  • Brake force distribution function

  • Hill start assist function

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF).

  2. Start the engine.

  3. Perform self-diagnosis for “ABS”.

Is DTC “C1071” detected?

YES>>

“CRNT” is displayed: Refer to Diagnosis Procedure.

YES>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End

Diagnosis Procedure

CALIBRATION OF DECEL G SENSOR

Perform calibration of decel G sensor. Refer to Work Procedure.

>>

GO TO 2.

PERFORM SELF-DIAGNOSIS

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF).

  2. Start the engine.

  3. Perform self-diagnosis for “ABS”.

Is DTC “C1071-54” detected?

YES>>

Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.

NO>>

Inspection End

C1073 Vacuum Sensor Nissan Pathfinder SUV

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C1073–01

Vacuum sensor

(Vacuum sensor)
1 Diagnosis condition
  • When ignition switch is ON.

  • When the power supply voltage is normal.

Signal (terminal) Vacuum sensor signal
Threshold When an open circuit is detected in brake vacuum sensor circuit.
Diagnosis delay time 1 second or less
2 Diagnosis condition
  • When ignition switch is ON.

  • When the power supply voltage is normal.

Signal (terminal) Vacuum sensor signal
Threshold When a short circuit is detected in brake vacuum sensor circuit.
Diagnosis delay time 1 second or less
3 Diagnosis condition
  • When ignition switch is ON.

  • When the power supply voltage is normal.

Signal (terminal) Vacuum sensor signal
Threshold When a malfunction is detected in brake vacuum sensor noise.
Diagnosis delay time 1 second or less
C1073–1C

Vacuum sensor

(Vacuum sensor)
1 Diagnosis condition
  • When ignition switch is ON.

  • When the power supply voltage is normal.

Signal (terminal) Vacuum sensor signal
Threshold When an open circuit is detected in brake vacuum sensor circuit.
Diagnosis delay time 1 second or less
2 Diagnosis condition
  • When ignition switch is ON.

  • When the power supply voltage is normal.

Signal (terminal) Vacuum sensor signal
Threshold When a short circuit is detected in brake vacuum sensor circuit.
Diagnosis delay time 1 second or less
3 Diagnosis condition
  • When ignition switch is ON.

  • When the power supply voltage is normal.

Signal (terminal) Vacuum sensor signal
Threshold When a malfunction is detected in brake vacuum sensor noise.
Diagnosis delay time 1 second or less
C1073–55

Vacuum sensor

(Vacuum sensor)
1 Diagnosis condition
  • When ignition switch is ON.

  • When the power supply voltage is normal.

Signal (terminal) Vacuum sensor signal
Threshold When an open circuit is detected in brake vacuum sensor circuit.
Diagnosis delay time 1 second or less
2 Diagnosis condition
  • When ignition switch is ON.

  • When the power supply voltage is normal.

Signal (terminal) Vacuum sensor signal
Threshold When a short circuit is detected in brake vacuum sensor circuit.
Diagnosis delay time 1 second or less
3 Diagnosis condition
  • When ignition switch is ON.

  • When the power supply voltage is normal.

Signal (terminal) Vacuum sensor signal
Threshold When a malfunction is detected in brake vacuum sensor noise.
Diagnosis delay time 1 second or less
C1073–1C

Vacuum sensor

(Vacuum sensor)
1 Diagnosis condition
  • When ignition switch is ON.

  • When the power supply voltage is normal.

Signal (terminal) Vacuum sensor signal
Threshold When an open circuit is detected in brake vacuum sensor circuit.
Diagnosis delay time 1 second or less
2 Diagnosis condition
  • When ignition switch is ON.

  • When the power supply voltage is normal.

Signal (terminal) Vacuum sensor signal
Threshold When a short circuit is detected in brake vacuum sensor circuit.
Diagnosis delay time 1 second or less
3 Diagnosis condition
  • When ignition switch is ON.

  • When the power supply voltage is normal.

Signal (terminal) Vacuum sensor signal
Threshold When a malfunction is detected in brake vacuum sensor noise.
Diagnosis delay time 1 second or less

POSSIBLE CAUSE

PAST DTCCRNT DTC
  • Harness or connector

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12V battery

  • Harness or connector

  • Brake vacuum sensor

  • ABS actuator and electric unit (control unit)

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12V battery

FAIL-SAFE

The following functions are suspended:

Brake assist function

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF).

  2. Start the engine.

  3. Perform self-diagnosis for “ABS”.

Is DTC “C1073” detected?

YES>>

“CRNT” is displayed: Refer to Diagnosis Procedure.

YES>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End

Diagnosis Procedure

CHECK CONNECTOR

  1. Disconnect 12V battery negative terminal.

  2. Check the brake vacuum sensor harness connector for disconnection or looseness.

  3. Check the ABS actuator and electric unit (control unit) harness connector for disconnection or looseness.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair / replace harness or connector. GO TO 2.

CHECK TERMINAL

  1. Disconnect brake vacuum sensor harness connector.

  2. Check the brake vacuum sensor terminals for damage or loose connection with harness connector.

  3. Disconnect ABS actuator and electric unit (control unit) harness connector.

  4. Check the ABS actuator and electric unit (control unit) terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair / replace harness, connector, or terminal.

CHECK BRAKE VACUUM SENSOR CIRCUIT

  1. Check the continuity between brake vacuum sensor harness connector and ABS actuator and electric unit (control unit) harness connector.

    Brake vacuum sensorABS actuator and electric unit (control unit)Continuity
    ConnectorTerminalConnectorTerminal
    E167 1 E125 45 Yes
    2 28
    3 17
  2. Check the continuity between brake vacuum sensor harness connector and ground.

    Brake vacuum sensor—Continuity
    ConnectorTerminal
    E167 1 Ground No
    2
    3

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair / replace harness or connector.

REPLACE BRAKE VACUUM SENSOR

CONSULT

  1. Connect ABS actuator and electric unit (control unit) harness connector.

  2. Replace the brake vacuum sensor. Refer to Removal and Installation.

  3. Connect 12V battery negative terminal.

  4. Erase self-diagnosis result for “ABS”.

  5. Ignition switch OFF (Auto ACC function OFF) → ON → OFF (Auto ACC function OFF).

  6. Start engine.

  7. Perform self-diagnosis for “ABS”.

Is DTC “C1073-01” detected?

YES>>

Replace the ABS actuator and electric unit (control unit). Refer to Removal and Installation.

NO>>

Inspection End

C1077 Dds Switch Nissan Pathfinder 2022

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C1077–55

DDS switch

(Transmission control module)
Diagnosis condition
  • When ignition switch is ON.

  • When the power supply voltage is normal.

Signal (terminal) CAN communication signal
Threshold When a malfunction is detected in TCM system.
Diagnosis delay time 2 seconds or less
C1077–92

DDS switch

(Transmission control module)
Diagnosis condition
  • When ignition switch is ON.

  • When the power supply voltage is normal.

Signal (terminal) CAN communication signal
Threshold When a malfunction is detected in TCM system.
Diagnosis delay time 2 seconds or less

POSSIBLE CAUSE

PAST DTCCRNT DTC
  • Harness or connector

  • CAN communication line

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12V battery

  • Harness or connector

  • CAN communication line

  • TCM

  • ABS actuator and electric unit (control unit)

  • ABS actuator and electric unit (control unit) power supply system

  • Fuse

  • Fusible link

  • 12V battery

FAIL-SAFE

Normal control

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always ignition switch OFF (Auto ACC function OFF) before conducting the next test.

>>

GO TO 2.

CHECK DTC DETECTION

CONSULT

  1. Ignition switch OFF (Auto ACC function OFF).

  2. Start the engine.

  3. Perform self-diagnosis for “ABS”.

Is DTC “C1077” detected?

YES>>

“CRNT” is displayed: Refer to Diagnosis Procedure.

YES>>

“PAST” is displayed: Inspection End (Erase the memory of self-diagnosis results.)

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: Inspection End

Diagnosis Procedure

CHECK TCM SYSTEM

CONSULT

Perform self-diagnosis for “TRANSMISSION”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

GO TO 2.

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIRCUIT

Check the ABS actuator and electric unit (control unit) power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair / replace harness, connector, terminal, fuse, or fusible link.

CHECK CONNECTOR AND TERMINAL

  1. Disconnect 12V battery negative terminal.

  2. Disconnect TCM harness connector.

  3. Disconnect ABS actuator and electric unit (control unit) harness connector.

  4. Check the connector for disconnection or looseness.

  5. Check the terminals for damage or loose connection with harness connector.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair / replace harness, connector, or terminal, securely lock the connector. GO TO 4.

PERFORM SELF-DIAGNOSIS

CONSULT

  1. Connect TCM harness connector.

  2. Connect ABS actuator and electric unit (control unit) harness connector.

  3. Connect 12V battery negative terminal.

  4. Erase self-diagnosis result for “ABS”.

  5. Ignition switch OFF (Auto ACC function OFF) → ON → OFF (Auto ACC function OFF).

  6. Start the engine.

  7. Perform self-diagnosis for “ABS”.

Is DTC detected?

YES>>

Check the DTC. Refer to DTC Index.

NO>>

Inspection End