Steering Control System - Basic Inspection
- Diagnosis and Repair Work Flow
- Additional Service When Replacing Eps Control Unit
Diagnosis and Repair Work Flow Nissan Pathfinder 2026
Work Flow
DETAILED FLOW
INTERVIEW FROM THE CUSTOMER
Clarify customer complaints before inspection. First of all, perform an interview utilizing reproduce symptoms as well as fully understand it. Ask customer about his/her complaints carefully. Check symptoms by driving Nissan Pathfinder vehicle with customer, if necessary.
>>GO TO 2.
CHECK SYMPTOM
Reproduce the symptom that is indicated by the customer, based on the information from the customer obtained by interview. Also check that the symptom is not caused by protection function. Refer to Protection Function.
>>GO TO 3.
CHECK Nissan Pathfinder Vehicle CONDITION
CONSULT
Ignition switch ON.
Check “HEAT PROTECT STATUS“ in “Data Monitor“ mode of “EPS/DAST 3“.
Monitor item Values HEAT PROTECT STATUS NORMAL
Is the inspection result normal?
YES>>GO TO 4.
NO>>Wait with the ignition switch OFF until the data monitor indication becomes “NORMAL”. And then GO TO 4.
PERFORM SELF-DIAGNOSIS
CONSULT
Select "Self Diagnostic Result" mode of "EPS/DAST 3".
Is any DTC detected?
YES>>Record or print DTC and freeze frame data (FFD). GO TO 5.
NO>>GO TO 7.
RECHECK SYMPTOM
CONSULT
Erase “Self Diagnostic Result” mode of “EPS/DAST 3”.
Perform DTC confirmation procedures for the malfunctioning system.
Is any DTC detected?
YES>>GO TO 6.
NO>>Check harness and connectors based on the information obtained by interview. Refer to Diagnostic Work Sheet.
REPAIR OR REPLACE MALFUNCTIONING PARTS
Repair or replace malfunctioning components.
Reconnect part or connector after repairing or replacing.
When DTC is detected, erase “Self Diagnostic Result” mode of “EPS/DAST 3”.
GO TO 8.
IDENTIFY MALFUNCTIONING SYSTEM BY SYMPTOM DIAGNOSIS
Estimate malfunctioning system based on symptom diagnosis and perform inspection.
Can the malfunctioning system be identified?
YES>>GO TO 8.
NO>>Check harness and connectors based on the information obtained by interview. Refer to Diagnostic Work Sheet.
FINAL CHECK
CONSULT
Check the reference value for EPS control unit.
Recheck the symptom and check that symptom is not reproduced on the same conditions.
Is the symptom reproduced?
YES>>GO TO 3.
NO>>Inspection End.
Diagnostic Work Sheet
Description
In general, customers have their own criteria for a problem. Therefore, it is important to understand the symptom and status well enough by asking the customer about his/her concerns carefully. To systemize all the information for the diagnosis, prepare the interview sheet referring to the interview points.
In some cases, multiple conditions that appear simultaneously may cause a DTC to be detected.
Interview sheet sample
| Interview sheet | |||||
|---|---|---|---|---|---|
| Customer name | MR/MS | Registration number | Initial year registration | ||
| Nissan Pathfinder Vehicle type | VIN | ||||
| Storage date | Engine | Mileage | km (Mile) | ||
| Symptom | □The steering wheel position (center) is in the wrong position. | ||||
| □Warning lamp turns on. | |||||
| □Noise □Vibration | |||||
□Others ( ) |
|||||
| First occurrence | □Recently □Others ( ) | ||||
| Frequency of occurrence | □Always □Under a certain conditions of □Sometimes (time(s)/day) | ||||
| Climate conditions | □Irrelevant | ||||
| Weather | □Fine □Cloud □Rain □Snow □Others ( ) | ||||
| Temperature | □Hot □Warm □Cool □Cold □Temperature [Approx. °C (°F)] | ||||
| Relative humidity | □High □Moderate □Low | ||||
| Road conditions | □Urban area □Suburb area □High way □Mountain road (uphill or down hill) □Rough road |
||||
| Operation conditions, etc. | □Irrelevant □When engine starts □During idling □During driving □During acceleration □At constant speed driving □During deceleration □During cornering (right curve or left curve) □During steering |
||||
| Other conditions | |||||
Memo |
|||||
Additional Service When Replacing Eps Control Unit Nissan Pathfinder Fifth generation
Work Procedure
DESCRPITION
When replacing the EPS control unit, the procedures of BEFORE REPLACEMENT and AFTER REPLACEMENT must be performed. For work procedure, refer to the following:
Before EPS control unit replacement.
After EPS control unit replacement.
BEFORE REPLACEMENT
When replacing the EPS control unit, save “Operation log”.
AFTER REPLACEMENT
After replacing the EPS control unit, the following items must be performed:
EPS control unit programming
Adjust the neutral position of steering angle sensor.
Register intelligent keys
WORK PROCEDURE (BEFORE REPLACING EPS CONTROL UNIT)
SAVE “OPERATION LOG”
CONSULT
Save “Operation Log”, according to the procedure of “Programming” in CONSULT Operation Manual.
>>Replace the EPS control unit. Refer to Removal and Installation.
After replacing the EPS control unit, perform necessary work.
WORK PROCEDURE (AFTER REPLACING EPS CONTROL UNIT)
CHECK “OPERATION LOG”
CONSULT
Check “Operation Log” saved before replacing the EPS control unit, according to the procedure of “Programming” in CONSULT Operation Manual.
Is there an applicable Operation Log in the Saved Data List?
YES>>GO TO 2.
NO>>GO TO 3.
PERFORM EPS CONTROL UNIT PROGRAMMING
CONSULT
Perform EPS control unit programming, according to “Programming” of CONSULT Operation Manual. Refer to CONSULT Operation Manual.
Ignition switch: ON
Electric load: OFF
Steering wheel: Not steering
Battery voltage: 12 – 13.5 V (Check the value displayed on the CONSULT screen.)
Nissan Pathfinder Vehicle speed: 0 km/h
GO TO 5.
READ IN EPS CONTROL UNIT PART NUMBER BY “FAST LINKED”
Obtain EPS control unit part number by NISSAN PARTS CATALOGUE GLOBAL Web-FAST, according to the procedure of ‘FAST linked’ in CONSULT Operation Manual. Refer to CONSULT Operation Manual.
>>GO TO 4.
PERFORM PROGRAMMING (FAST LINKED)
CONSULT
Perform EPS control unit programming according to the procedure of FAST linked in CONSULT Operation Manual. Refer to CONSULT Operation Manual.
Ignition switch: ON
Electric load: OFF
Steering wheel: Not steering
Battery voltage: 12 – 13.5 V (Check the value displayed on the CONSULT screen.)
Nissan Pathfinder Vehicle speed: 0 km/h
GO TO 5.
PERFORM NECESSARY WORK
Perform adjustment of steering angle sensor neutral position. Refer to Work Procedure.
Select "Self Diagnostic Result" mode of "EPS/DAST 3".
Erase "Self Diagnostic Result" mode of "EPS/DAST 3".
GO TO 6.
REGISTER INTELLIGENT KEYS
Register Intelligent Keys. For initialization and registration of Intelligent Key: Refer to CONSULT Immobilizer mode and follow the on-screen instructions.
Work End.