Dtc/circuit Diagnosis (Active Grille Shutter ... High Pressure Fuel Pump)

In this manual: Dtc/circuit Diagnosis (Active Grille Shutter ... High Pressure Fuel Pump)
General Information — 8Engine :: Engine Mechanical — 19Engine Lubrication System - Precautions. Preparation — 1Engine Lubrication System - Lubrication System (System Description). Engine Oil Pressure (Basic Inspection). Service Data and Specifications (SDS) — 1Engine Cooling System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Engine Cooling System - Engine Coolant — 1Engine Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Engine Control System - Ecu Diagnosis Information — 1Ecu Diagnosis Information - Ecm ++ — 1Engine Control System - Basic Inspection — 1Basic Inspection - Diagnosis and Repair Workflow ++ — 1Basic Inspection - Basic Inspection ++ — 1Basic Inspection - Additional Service When Replacing Ecm ++ — 1Basic Inspection - Fuel Pressure Check ++ — 1Basic Inspection - How to Set Srt Code ++ — 1Basic Inspection - How to Erase Permanent Dtc ++ — 1Engine Control System - Dtc/circuit Diagnosis — 1Engine Control System - Symptom Diagnosis — 1Engine Control System - Periodic Maintenance — 1Engine Control System - Removal and Installation — 1Fuel System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Fuel System - Fuel System (Periodic Maintenance). Fuel Level Sensor Unit (Disassembly and Assembly) — 1Exhaust System - Precautions. Preparation — 1Exhaust System - Exhaust System (Periodic Maintenance). Exhaust System (Removal and Installation) — 1Starting System - Precautions. Preparation. Starter Motor (Service Data and Specifications (sds)) — 1Starting System - Diagnosis and Repair Work Flow — 1Starting System - Starting System (Symptom Diagnosis). Starter Motor (Removal and Installation) — 1Accelerator Control System - Precautions. Service Data and Specifications (SDS) — 1Accelerator Control System - Accelerator Pedal Assembly — 1Transmission & Driveline :: Transaxle & Transmission — 21Driveline - System Description — 1Transfer: Ty92b - Ecu Diagnosis Information. Awd Control Unit ++ — 1Driveline - Basic Inspection — 1Driveline - Dtc/circuit Diagnosis — 1Driveline - Symptom Diagnosis — 1Driveline - Removal and Installation — 1Transfer: Ty92b - Unit Removal and Installation. Transfer Assembly ++ — 1Driveline - Unit Disassembly and Assembly — 1Driveline - Basic Inspection — 1Driveline - Removal and Installation — 1Driveline - Unit Disassembly and Assembly — 1Front Axle - Precautions. Preparation — 1Front Axle - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Front Axle - Front Drive Shaft Boot — 1Front Axle - Front Drive Shaft — 1Rear Axle - Precautions. Preparation. Service Data and Specifications (SDS) — 1Rear Axle - Noise, Vibration and Harshness (nvh) Troubleshooting — 1Rear Axle - Rear Drive Shaft — 1Suspension :: Front Suspension — 7Rear Suspension - Precautions. Preparation — 1Rear Suspension - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Rear Suspension - Rear Suspension Assembly — 1Road Wheels & Tires - Precautions — 1Road Wheels & Tires - Preparation. Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Road Wheels & Tires - System — 1Brakes :: Brake System — 9Parking Brake System - Precautions. Preparation — 1Parking Brake System - System — 1Vdc/tcs/abs - Precautions ++ — 1Brake Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Dtc/circuit Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Steering :: Steering System — 9Steering Control System - Precautions — 1Steering Control System - System — 1Steering Control System - Eps Control Unit (Ecu Diagnosis Information. Removal and Installation) — 1Restraints :: Seat Belt — 7Srs Air Bag - Precautions. Preparation — 1Srs Air Bag - Collision Diagnosis — 1Srs Air Bag - Occupant Classification System — 1Srs Air Bag Control System - Precautions — 1Srs Air Bag Control System - System — 1Srs Air Bag Control System - Diagnosis Sensor Unit — 1Srs Air Bag Control System - Inspection and Adjustment — 1Ventilation, Heater & Air Conditioner :: Ventilation System — 6Heater & Air Conditioning System - Precautions — 1Heater & Air Conditioning System - Preparation — 1Heater & Air Conditioning System - Component Parts — 1Heater & Air Conditioning System - Diagnosis and Repair Work Flow — 1Heater & Air Conditioning System - Compressor — 1Heater & Air Conditioning System - Cooler Pipe and Hose — 1Heater & Air Conditioning System - Condenser. Condenser — 1Heater & Air Conditioning System - Heating and Cooling Unit Assembly — 1Heater & Air Conditioning System - Service Data and Specifications (SDS) — 1Heater & Air Conditioning Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1Heater & Air Conditioning Control System - Ecu Diagnosis Information — 1Heater & Air Conditioning Control System - Basic Inspection — 1Heater & Air Conditioning Control System - Dtc/circuit Diagnosis — 1Heater & Air Conditioning Control System - Symptom Diagnosis — 1Heater & Air Conditioning Control System - Removal and Installation — 1Body Interior :: Interior — 8Instrument Panel - Precautions. Preparation. Clip List — 1Instrument Panel - Squeak and Rattle Trouble Diagnoses — 1Instrument Panel - Cluster Lid C — 1Seat - Precautions — 1Seat - Preparation. Clip List — 1Seat - Component Parts — 1Seat - System — 1Seat - Diagnosis and Repair Work Flow — 1Seat - Front Seat — 1Seat - Second Row Seats — 1Seat - Third Row Seats — 1Seat - Front Seat — 1Seat - Second Row Seat — 1Seat - Third Row Seat — 1Automatic Drive Positioner - Precautions. Preparation — 1Automatic Drive Positioner - System — 1Automatic Drive Positioner - Diagnosis and Repair Work Flow — 1Automatic Drive Positioner - Inspection and Adjustment — 1Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock — 38Security Control System - Precautions — 1Security Control System - System — 1Security Control System - Ecm, Bcm, Intelligent Key Unit, Ipdm E/r — 1Security Control System - Vehicle Security System Cannot Be Set — 1Glass & Window System - Precautions. Preparation — 1Glass & Window System - Squeak and Rattle Trouble Diagnoses — 1Power Window Control System - Precautions. Preparation — 1Power Window Control System - Power Supply and Ground Circuit — 1Power Window Control System - Power Window Motor Circuit — 1Power Window Control System - Front Power Window Rh Alone Does Not Operate — 1Power Window Control System - Rear Lh Side Power Window Alone Does Not Operate — 1Power Window Control System - Rear Rh Side Power Window Alone Does Not Operate — 1Roof - Precautions. Preparation — 1Roof - Power Supply and Ground Circuit — 1Roof - Moonroof Switch Assembly — 1Roof - Lin Communication Circuit — 1Roof - Auto Operation Does Not Operate — 1Roof - Anti-Pinch Function Does Not Operate — 1Exterior - Precautions. Preparation. Clip List (Preparation) — 1Exterior - Squeak and Rattle Trouble Diagnoses — 1Exterior - Fender Protector — 1Exterior - Over Fender — 1Exterior - Under Cover — 1Exterior - Roof Side Rail — 1Body Repair - Service Information — 1Service Information - Sheet Metal Work ++ — 1Service Information - Body Welding and Precautions ++ — 1Service Information - Safety and Health ++ — 1Service Information - Repairing Procedures and Precautions ++ — 1Body Repair - Precaution — 1Body Repair - Preparation — 1Body Repair - Removal and Installation — 1Driver Controls :: Mirrors — 8Exterior Lighting System - System Description — 1System Description - Component Parts ++ — 1Exterior Lighting System - Basic Inspection — 1Exterior Lighting System - Dtc/circuit Diagnosis — 1Exterior Lighting System - Symptom Diagnosis — 1Exterior Lighting System - Periodic Maintenance — 1Exterior Lighting System - Removal and Installation — 1Interior Lighting System - Precautions. Preparation — 1Interior Lighting System - Component Parts. Interior Lighting System — 1Interior Lighting System - System — 1Interior Lighting System - Diagnosis and Repair Work Flow — 1Interior Lighting System - Interior Lighting System Symptoms (Symptom Diagnosis). Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Interior Lighting System - Foot Lamp — 1Wiper & Washer - Precautions — 1Wiper & Washer - Preparation. Bcm, Ipdm E/r (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Wiper & Washer - System — 1Wiper & Washer - Diagnosis and Repair Work Flow — 1Defogger - Precautions. Bcm, A/c Auto Amp. (Ecu Diagnosis Information) — 1Defogger - Diagnosis and Repair Work Flow — 1Horn - Precautions — 1Electrical & Power Control :: Power Outlet — 13Body Control System - Precautions. Preparation — 1Body Control System - Component Parts — 1Body Control System - System — 1Body Control System - Diagnosis System (bcm) — 1Body Control System - Bcm — 1Lan System - System Description — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - Removal and Installation — 1Charging System - Precautions. Preparation. Ecm, Ipdm E/r (Ecu Diagnosis Information) — 1Charging System - Diagnosis and Repair Work Flow — 1Charging System - Charging System (Symptom Diagnosis). Generator (Removal and Installation). Service Data and Specifications (SDS) — 1Power Supply, Ground & Circuit Elements - Precautions. Preparation. Service Data and Specifications (SDS) — 1Driver Information & Multimedia :: Meter, Warning Lamp & Indicator — 25Warning Chime System - Application Notice (How to Use This Manual). Precautions — 1Warning Chime System - System — 1Warning Chime System - Diagnosis System (combination Meter) — 1Warning Chime System - Bcm, Combination Meter (Ecu Diagnosis Information). Diagnosis and Repair Work Flow (Basic Inspection) — 1Sonar System - Precautions. Preparation — 1Sonar System - Sonar Control Unit — 1Dtc/circuit Diagnosis - B2720 Corner Sensor [rl] ++ — 1Audio, Visual & Navigation System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Multi Av (av Control Unit) ++ — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Symptom Diagnosis - Multi Av System ++ — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Cruise Control & Driver Assistance :: Cruise Control System — 17Driver Assistance System - System Description — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Driver Assistance System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1System Description - Handling Precaution ++ — 1Driver Assistance System - Ecu Diagnosis Information — 1Driver Assistance System - Basic Inspection — 1Basic Inspection - Distance Sensor Alignment ++ — 1Basic Inspection - Camera Aiming Adjustment ++ — 1Basic Inspection - Action Test ++ — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Laser/radar (distance Sensor) ++ — 1Dtc/circuit Diagnosis - Lane Camera (front Camera Unit) ++ — 1Driver Assistance System - Symptom Diagnosis — 1Driver Assistance System - Removal and Installation — 1Driver Assistance System - System Description — 1System Description - System ++ — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Drive Mode System - Precautions — 1Drive Mode System - Component Parts. Drive Mode System — 1Drive Mode System - System — 1Drive Mode System - Diagnosis and Repair Work Flow — 1Drive Mode System - Drive Mode Select Switch Circuit — 1Maintenance - Precautions. Preparation — 1Maintenance - General Maintenance — 1Maintenance - Periodic Maintenance — 1Maintenance - Recommended Fluids and Lubricants — 1Maintenance - Engine Maintenance — 1Maintenance - Chassis and Body Maintenance — 1Engine Lubrication System - Periodic Maintenance — 1Engine Lubrication System - Removal and Installation — 1Engine Cooling System - System Description — 1Engine Cooling System - Removal and Installation — 1Engine Control System - Vq35dd — 1Fuel System - Removal and Installation — 1Starting System - System Description — 1Starting System - Dtc/circuit Diagnosis — 1Driveline - Transfer: Ty92b — 1Driveline - Rear Propeller Shaft: 3fcj-Cvj — 1Driveline - Rear Final Drive: R145 — 1Front Axle - Periodic Maintenance — 1Front Axle - Removal and Installation — 1Rear Axle - Periodic Maintenance — 1Rear Axle - Removal and Installation — 1Rear Suspension - Removal and Installation — 1Road Wheels & Tires - System Description — 1Road Wheels & Tires - Basic Inspection — 1Road Wheels & Tires - Dtc/circuit Diagnosis — 1Road Wheels & Tires - Symptom Diagnosis — 1Road Wheels & Tires - Periodic Maintenance — 1Road Wheels & Tires - Removal and Installation — 1Parking Brake System - System Description — 1Parking Brake System - Basic Inspection — 1Parking Brake System - Dtc/circuit Diagnosis — 1Parking Brake System - Symptom Diagnosis — 1Parking Brake System - Removal and Installation — 1Brake Control System - Vdc/tcs/abs — 1Brake Control System - Automatic Brake Hold — 1Brake Control System - Automatic Emergency Braking — 1Brake Control System - Rear Automatic Braking — 1Steering Control System - System Description — 1Steering Control System - Basic Inspection — 1Steering Control System - Dtc/circuit Diagnosis — 1Steering Control System - Symptom Diagnosis — 1Srs Air Bag - Removal and Installation — 1Srs Air Bag Control System - System Description — 1Srs Air Bag Control System - Basic Inspection — 1Srs Air Bag Control System - Symptom Diagnosis — 1Heater & Air Conditioning System - Symptom Diagnosis — 1Heater & Air Conditioning System - Periodic Maintenance — 1Heater & Air Conditioning Control System - Automatic Air Conditioning — 1Instrument Panel - Removal and Installation — 1Instrument Panel - Unit Disassembly and Assembly — 1Seat - Ecu Diagnosis Information — 1Seat - Dtc/circuit Diagnosis — 1Seat - Symptom Diagnosis — 1Automatic Drive Positioner - System Description — 1Automatic Drive Positioner - Ecu Diagnosis Information — 1Automatic Drive Positioner - Dtc/circuit Diagnosis — 1Automatic Drive Positioner - Symptom Diagnosis — 1Automatic Drive Positioner - Removal and Installation — 1Security Control System - System Description — 1Security Control System - Basic Inspection — 1Security Control System - Dtc/circuit Diagnosis — 1Security Control System - Symptom Diagnosis — 1Security Control System - Removal and Installation — 1Glass & Window System - Removal and Installation — 1Power Window Control System - System Description — 1Power Window Control System - Ecu Diagnosis Information — 1Power Window Control System - Basic Inspection — 1Power Window Control System - Dtc/circuit Diagnosis — 1Power Window Control System - Symptom Diagnosis — 1Power Window Control System - Removal and Installation — 1Roof - System Description — 1Roof - Ecu Diagnosis Information — 1Roof - Basic Inspection — 1Roof - Dtc/circuit Diagnosis — 1Roof - Symptom Diagnosis — 1Roof - Removal and Installation — 1Exterior - System Description — 1Exterior - Removal and Installation — 1Body Repair - Repair Information — 1Exterior Lighting System - Led Headlamp — 1Interior Lighting System - Dtc/circuit Diagnosis — 1Interior Lighting System - Removal and Installation — 1Wiper & Washer - System Description — 1Wiper & Washer - Dtc/circuit Diagnosis — 1Wiper & Washer - Symptom Diagnosis — 1Wiper & Washer - Removal and Installation — 1Defogger - System Description — 1Defogger - Dtc/circuit Diagnosis — 1Defogger - Symptom Diagnosis — 1Defogger - Removal and Installation — 1Horn - Removal and Installation — 1Body Control System - Basic Inspection — 1Body Control System - Dtc/circuit Diagnosis — 1Body Control System - Symptom Diagnosis — 1Body Control System - Removal and Installation — 1Lan System - Can Fundamental — 1Lan System - Can — 1Lan System - Can Gateway — 1Power Control System - Ipdm E/r — 1Power Control System - Power Distribution System — 1Charging System - System Description — 1Charging System - Dtc/circuit Diagnosis — 1Power Supply, Ground & Circuit Elements - System Description — 1Power Supply, Ground & Circuit Elements - Basic Inspection — 1Power Supply, Ground & Circuit Elements - Removal and Installation — 1Warning Chime System - System Description — 1Warning Chime System - Dtc/circuit Diagnosis — 1Warning Chime System - Symptom Diagnosis — 1Sonar System - System Description — 1Sonar System - Basic Inspection — 1Sonar System - Dtc/circuit Diagnosis — 1Sonar System - Symptom Diagnosis — 1Sonar System - Removal and Installation — 1Audio, Visual & Navigation System - Nissanconnect — 1Audio, Visual & Navigation System - Intelligent Around View Monitor System — 1Audio, Visual & Navigation System - Rear View Monitor System — 1Audio, Visual & Navigation System - Telematics System — 1Driver Assistance System - Adas Control Unit 2 — 1Driver Assistance System - Driver Assistance System — 1Driver Assistance System - Chassis Control — 1Drive Mode System - Removal and Installation — 1Dtc/circuit Diagnosis (C053c Wheel Speed Sensor ... U2141 Can Comm Circuit) — 1Dtc/circuit Diagnosis (P0011 Intake Valve Timing Control ... P0111 Iat Sensor) — 1Dtc/circuit Diagnosis (P0116 Engine Coolant Temperature Sensor ... P025b Fuel Pump Module a) — 1Dtc/circuit Diagnosis (P026b Injection Timing ... P0420 Three Way Catalyst Function) — 1Dtc/circuit Diagnosis (P0441 Evap Control System ... P0524 Engine Oil Pressure) — 1Dtc/circuit Diagnosis (P0532 A/c Refrigerant Pressure Sensor ... P064d Ecm) — 1Dtc/circuit Diagnosis (P06da Engine Oil Pressure Control Solenoid Valve ... P1217 Engine Over Temperature) — 1Dtc/circuit Diagnosis (P1220 Fuel Pump Control Module (fpcm) ... P1574 Ascd Vehicle Speed Sensor) — 1Dtc/circuit Diagnosis (P1575 Brake Switch ... P2101 Electric Throttle Control Function) — 1Dtc/circuit Diagnosis (P2118 Throttle Control Motor ... P34ac Electric Intake Valve Timing Control Actuator) — 1Dtc/circuit Diagnosis (Active Grille Shutter ... High Pressure Fuel Pump) — 1Dtc/circuit Diagnosis (Ignition Signal ... Variable Induction Air System) — 14012 C1040 Emergency Brake — 14013 C106a Wheel Sensor — 14014 C1078-55 Not Configuration — 14015 C10b4-98 Overheat — 14016 B1001 Lap Pre-Tensioner Lh — 14017 B0001 Driver Air Bag Module — 14018 B100e Knee Air Bag Module Rh — 14019 B142x Collision Detection — 1Dtc/circuit Diagnosis (B20c7-11 A/c Clutch ... B24a6-11 in-Vehicle Sensor) — 1Dtc/circuit Diagnosis (B24a6-15 in-Vehicle Sensor ... U2140-87 Can Comm Err (ecm)) — 1Dtc/circuit Diagnosis (C1f00-1c Control Unit ... C1f04-61 Brake Sw/stop Lamp Sw) — 1Dtc/circuit Diagnosis (C1f05-49 Front Camera Unit ... C1f70-87 Ethernet Circuit) — 1
180steps
~1080min
4/5difficulty
Done 0 of 180
  • Active Grille Shutter
  • Ascd Indicator
  • Cooling Fan
  • Crankshaft Position Sensor 2
  • Electrical Load Signal
  • Electronic Controlled Engine Mount
  • Fuel Injector
  • Fuel Pump
  • High Pressure Fuel Pump

Active Grille Shutter Nissan Pathfinder 5th Gen

Component Inspection

CHECK ACTIVE GRILLE SHUTTER

With CONSULT

  1. Start the engine.

  2. Select “ACTIVE GRILLE SHUTTER” in “ACTIVE TEST” mode of “ENGINE” using CONSULT.

  3. Touch “CALIBRTN”.

  4. After the calibration completes, check the operation of active grille shutter as follows.

    ConditionActive grille shutter
    Select “CLOSE” Open → Close
    Select “OPEN” Close → Open

Without CONSULT

  1. Turn ignition switch OFF.

  2. Operate shutter by hands to close position.

  3. Check the operation of active grille shutter as follows.

    ConditionActive grille shutter
    Ignition switch: ON Close → Open

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace active grille shutter. Refer to Removal and Installation.

Ascd Indicator Nissan Pathfinder 5th Gen

Component Function Check

CHECK ASCD INDICATOR FUNCTION

Check ASCD indicator under the following conditions.

ASCD INDICATORCONDITIONSPECIFICATION
CRUISE LAMP
  • Ignition switch: ON

  • MAIN switch: Pressed at the 1st time →

    at the 2nd time

ON → OFF
SET LAMP
  • MAIN switch: ON

  • When Nissan Pathfinder vehicle speed is between 40 km/h and 144 km/h

  • ASCD: Operating

ON
  • ASCD: Not operating

OFF

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Proceed to Diagnosis Procedure.

Diagnosis Procedure

CHECK DTC

Check that DTC UXXXX is not displayed.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Perform trouble diagnosis for DTC UXXXX.

CHECK DTC WITH COMBINATION METER

Check DTC with combination meter.

  • FULL TFT METER: Refer to CONSULT Function (METER/M&A).

  • 7 INCH INFORMATION DISPLAY: Refer to CONSULT Function (METER/M&A).

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace.

CHECK INTERMITTENT INCIDENT

Refer to Intermittent Incident.

Is the inspection result normal?

YES>>

Replace combination meter.

  • FULL TFT METER: Refer to Removal and Installation.

  • 7 INCH INFORMATION DISPLAY: Refer to Removal and Installation.

NO>>

Repair or replace.

Cooling Fan Nissan Pathfinder R53

Component Function Check

CHECK COOLING FAN FUNCTION

With CONSULT

  1. Turn ignition switch ON.

  2. On CONSULT screen, select “ENGINE ”>>“Active Test”>>“FAN DUTY CONTROL”.

  3. Make sure that cooling fan speed varies according to the percentage.

Without CONSULT

  1. Perform IPDM E/R auto active test and check cooling fan motors operation, refer to CONSULT Function (IPDM E/R).

  2. Make sure that cooling fan operates.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Proceed to Diagnosis Procedure (Cooling Fan Motor).

Diagnosis Procedure (Cooling Fan Motor)

CHECK COOLING FAN CONTROL MODULE POWER SUPPLY-I

  1. Turn ignition switch OFF.

  2. Disconnect cooling fan control module harness connector.

  3. Turn ignition switch ON.

  4. Check the voltage between cooling fan control module harness connector and ground.

    + − Voltage
    Cooling fan control module
    Connector Terminal
    E225 3 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 11.

NO>>

GO TO 2.

CHECK COOLING FAN CONTROL MODULE POWER SUPPLY-II

  1. Turn ignition switch OFF.

  2. Remove cooling fan relay.

  3. Check the voltage between cooling fan relay harness connector and ground.

    + − Voltage
    Cooling fan relay
    Connector Terminal
    E82 3 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 3.

CHECK FUSIBLE LINK

Check that 60A fusible link (No. H) is not blowing.

Is the fusible link blown (open)?

YES>>

Perform trouble diagnosis for power supply circuit.

NO>>

Replace the fusible link after repairing the applicable circuit.

CHECK COOLING FAN CONTROL MODULE POWAR SUPPLY CIRCUIT

  1. Check the continuity between cooling fan relay harness connector and cooing fan control module harness connector.

    Cooling fan relay Cooling fan control module Continuity
    Connector Terminal Connector Terminal
    E82 5 E225 3 Existed
  2. Also check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace error-detected parts.

CHECK COOLING FAN RELAY DRIVE POWER SUPPLY

  1. Turn ignition switch ON.

  2. Check the voltage between cooling fan relay harness connector and ground.

    + − Voltage
    Cooling fan relay
    Connector Terminal
    E82 1 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

GO TO 6.

CHECK FUSE

  1. Turn ignition switch OFF.

  2. Check that 10A fuse (No. 9) is not blowing.

Is the fuse blown (open)?

YES>>

GO TO 7.

NO>>

Replace the fuse after repairing the applicable circuit.

CHECK COOLING FAN RELAY DRIVE POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect fuse block (J/B) harness connector.

  3. Check the continuity between fuse block (J/B) harness connector and cooing fan relay harness connector.

    Fuse block (J/B) Cooling fan relay Continuity
    Connector Terminal Connector Terminal
    E28 1R E82 1 Existed
  4. Also check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

GO TO 10

NO>>

Repair or replace error-detected parts.

CHECK COOLING FAN RELAY DRIVE SIGNAL CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect IPDM E/R harness connector.

  3. Check the continuity between IPDM E/R harness connector and cooing fan relay harness connector.

    IPDM E/R Cooling fan relay Continuity
    Connector Terminal Connector Terminal
    E78 107 E82 2 Existed
  4. Also check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Repair or replace error-detected parts.

CHECK COOLING FAN RELAY

Refer to Component Inspection (Cooling Fan Relay).

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Replace cooling fan relay.

CHECK INTERMITTENT INCIDENTE

Perform Intermittent Incident.

Is the inspection result normal?

YES>>

Replace IPDM E/R. Refer to Removal and Installation.

NO>>

Repair or replace error-detected parts.

CHECK COOLING FAN CONTROL MODULE GROUND CIRCUIT

  1. Turn ignition switch OFF.

  2. Check the continuity between cooling fan control module harness circuit.

    Cooling fan control module — Continuity
    Connector Terminal
    E225 1 Ground Existed
  3. Also check harness for short to power.

Is the inspection result normal?

YES>>

GO TO 12.

NO>>

Repair or replace error-detected parts.

CHECK COOLING FAN CONTROL SIGNAL

  1. Reconnect cooling fan control module harness connector.

  2. Start engine.

  3. Check the voltage between IPDM E/R harness connector and ground.

    + − Condition Voltage
    IPDM E/R
    Connector Terminal
    E78 106 Ground Engine idling 0 – 5 V

Is the inspection result normal?

YES>>

GO TO 13.

NO>>

GO TO 10.

CHECK COOLING FAN CONTROL SIGNAL CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect IPDM E/R harness connector and cooling fan control module harness connector.

  3. Check the continuity between IPDM E/R harness connector and cooing fan control module harness connector.

    IPDM E/R Cooling fan control module Continuity
    Connector Terminal Connector Terminal
    E78 106 E225 2 Existed
  4. Also check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

GO TO 14.

NO>>

Repair or replace error-detected parts.

CHECK COOLING FAN CONTROL MODULE OUTPUT SIGNAL

  1. Reconnect all harness connectors disconnected.

  2. Disconnect cooling fan control module harness connector.

  3. Turn ignition switch ON.

  4. Check the voltage between cooling fan control module connector and ground.

    + − Voltage
    Cooling fan control module
    Motor Connector Terminal
    1 E245 4 Ground Battery voltage
    2 E246 6

Is the inspection result normal?

YES>>

GO TO 15.

NO>>

Replace cooling fan control module. Refer to Exploded View.

CHECK COOLING FAN MOTOR

Refer to Component Inspection (Cooling Fan Motor).

Is the inspection result normal?

YES>>

Perform intermittent incident. Refer to Intermittent Incident

NO>>

Replace malfunctioning cooling fan motor. Refer to Exploded View.

Component Inspection (Cooling Fan Motor)

COOING FAN MOTOR 1

CHECK COOLING FAN MOTOR 1

  1. Turn ignition switch OFF.

  2. Disconnect cooling fan control module harness connector.

  3. Supply cooling fan control module harness connector terminals with battery voltage and check operation.

    Cooling fan control module Operation
    Connector + −
    Terminal
    E245 4 5 Cooling fan operates.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace cooling fan motor 1. Refer to Exploded View.

COOING FAN MOTOR 2

CHECK COOLING FAN MOTOR 2

  1. Turn ignition switch OFF.

  2. Disconnect cooling fan control module harness connector.

  3. Supply cooling fan control module harness connector terminals with battery voltage and check operation.

    Cooling fan control module Operation
    Connector + −
    Terminal
    E246 6 7 Cooling fan operates.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace cooling fan motor 2. Refer to Exploded View.

Component Inspection (Cooling Fan Relay)

CHECK COOLING FAN RELAY

  1. Turn ignition switch OFF.

  2. Remove cooling fan relay.

  3. Check the continuity between cooling fan relay terminals under the following conditions.

    Terminals Conditions Continuity
    and 12 V direct current supply between terminals and Existed
    No current supply Not existed

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace malfunctioning cooling fan relay.

Crankshaft Position Sensor 2 Nissan Pathfinder R53

Component Inspection (Crankshaft Position Sensor 2)

CHECK CRANKSHAFT POSITION SENSOR 2-1

  1. Turn ignition switch OFF.

  2. Loosen the fixing bolt of crankshaft position sensor 2.

  3. Disconnect crankshaft position sensor 2 harness connector.

  4. Remove the crankshaft position sensor 2.

  5. Visually check the crankshaft position sensor 2 for chipping.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace crankshaft position sensor 2. Refer to Component Parts Location.

CHECK CRANKSHAFT POSITION SENSOR 2-2

Check the resistance between crankshaft position sensor 2 terminals as follows.

Crankshaft position sensor 2ConditionResistance
Terminal (Polarity)
1 2 Temperature [°C (°F)] 25 (77) Except 0 or ∞Ω
3
2 3

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace crankshaft position sensor 2. Refer to Component Parts Location.

Electrical Load Signal Nissan Pathfinder 2022

Component Function Check

CHECK REAR WINDOW DEFOGGER SWITCH FUNCTION

With CONSULT

  1. Turn ignition switch ON.

  2. On CONSULT screen, select “ENGINE”>>“Data Monitor”.

  3. Check “LOAD SIGNAL” indication under the following conditions.

    Monitor itemConditionIndication
    LOAD SIGNAL Rear window defogger switch ON ON
    OFF OFF

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Proceed to Diagnosis Procedure.

CHECK LIGHTING SWITCH FUNCTION

With CONSULT

Check “LOAD SIGNAL” indication under the following conditions.

Monitor itemConditionIndication
LOAD SIGNAL Lighting switch ON at 2nd position ON
OFF OFF

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Proceed to Diagnosis Procedure.

CHECK HEATER FAN CONTROL SWITCH FUNCTION

With CONSULT

Select “HEATER FAN SW” and check indication under the following conditions.

Monitor itemConditionIndication
HEATER FAN SW Heater fan control switch ON ON
OFF OFF

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Proceed to Diagnosis Procedure.

Diagnosis Procedure

The electrical load signal (Headlamp switch signal, rear window defogger switch signal, etc.) is transferred via the CAN communication line.

INSPECTION START

Confirm the malfunctioning circuit (rear window defogger, headlamp or heater fan). Refer to Component Function Check.

Which circuit is related to the incident?

Rear window defogger>>

GO TO 2.

Headlamp>>

GO TO 3.

Heater fan>>

GO TO 4.

CHECK REAR WINDOW DEFOGGER SYSTEM

Refer to Work Flow.

>>

INSPECTION END

CHECK HEADLAMP SYSTEM

Refer to Work Flow.

>>

INSPECTION END

CHECK HEATER FAN CONTROL SYSTEM

Refer to Work Flow.

>>

INSPECTION END

Electronic Controlled Engine Mount Nissan Pathfinder

Component Function Check

CHECK OVERALL FUNCTION

  1. Start engine and warm it up to normal operating temperature.

  2. Shift selector position is D while depressing the brake pedal and parking brake pedal.

  3. Disconnect electronic controlled engine mount control solenoid valve harness connector.

  4. Check that body vibration increases compared to the condition of step 2 above (with Nissan Pathfinder vehicle stopped).

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Diagnosis Procedure.

Diagnosis Procedure

CHECK VACUUM SOURCE

  1. Turn ignition switch OFF.

  2. Reconnect electronic controlled engine mount control solenoid valve harness connector.

  3. Disconnect vacuum hose connected to electronic controlled engine mount.

  4. Start engine and let it idle.

  5. Check vacuum hose for vacuum existence.

    Vacuum should exist.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

GO TO 2.

CHECK VACUUM HOSES AND VACUUM GALLERY

  1. Turn ignition switch OFF.

  2. Check vacuum hoses and vacuum gallery for clogging, cracks or improper connection. Refer to System Description.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace vacuum hoses and vacuum gallery.

CHECK ELECTRONIC CONTROLLED ENGINE MOUNT CONTROL SOLENOID VALVE POWER SUPPLY

  1. Disconnect electronic controlled engine mount control solenoid valve harness connector.

  2. Turn ignition switch ON.

  3. Check the voltage between front electronic controlled engine mount harness connector and ground.

    + − Voltage
    Electronic controlled engine mount control solenoid valve
    Connector Terminal
    F64 1 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

GO TO 4.

CHECK ELECTRONIC CONTROLLED ENGINE MOUNT CONTROL SOLENOID VALVE POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect fuse block (J/B) harness connector.

  3. Check the continuity between electronic controlled engine mount harness connector and fuse block (J/B) harness connector.

Electronic controlled engine mount control solenoid valve Fuse block (J/B) Continuity
Connector Terminal Connector Terminal
F64 1 E55 7J Existed

Is the inspection result normal?

YES>>

Perform the trouble diagnosis for power supply circuit.

NO>>

Repair or replace error-detected parts.

CHECK ELECTRONIC CONTROLLED ENGINE MOUNT CONTROL SOLENOID VALVE OUTPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

  1. Disconnect ECM harness connector.

  2. Check the continuity between ECM harness connector and electronic controlled engine mount control solenoid valve harness connector.

    ECM Electronic controlled engine mount control solenoid valve Continuity
    Connector Terminal Connector Terminal
    F79 151 F64 2 Existed
  3. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair open circuit, short to ground or short to power in harness connectors.

CHECK ELECTRONIC CONTROLLED ENGINE MOUNT CONTROL SOLENOID VALVE

Check electronic controlled engine mount control solenoid valve. Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Replace electronic controlled engine mount control solenoid valve. Refer to Component Parts Location.

CHECK ELECTRONIC CONTROLLED ENGINE MOUNT

  1. Turn ignition switch OFF.

  2. Install vacuum pump (A) to electronic controlled engine mount .

  3. Check that a vacuum is maintained when applying the vacuum of −40 kPa (−0.41 kg/cm2, −5.8 psi) to electronic controlled engine mount.

  4. Also visually check electronic controlled engine mount.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Replace electronic controlled engine mount.

CHECK INTERMITTENT INCIDENT

Check intermittent incident. Refer to Intermittent Incident.

Is the inspection result normal?

YES>>

Replace intake manifold collector. Refer to Removal and Installation.

NO>>

Repair or replace error-detected parts.

Component Inspection

CHECK ELECTRONIC CONTROLLED ENGINE MOUNT CONTROL SOLENOID VALVE

With CONSULT

  1. Turn ignition switch OFF.

  2. Reconnect electronic controlled engine mount control solenoid valve harness connector.

  3. Disconnect vacuum hoses connected to electronic controlled engine mount control solenoid valve.

  4. Turn ignition switch ON.

  5. On CONSULT, select “ENGINE”>>“Active Test”>>“ENGINE MOUNTING”.

  6. Check air passage continuity and operation delay time under the following conditions.

    Condition

    (ENGINE MOUNTING)
    Air passage continuity between and

    Air passage continuity

    between and
    TRVL Existed Not existed
    IDLE Not existed Existed

Without CONSULT

  1. Turn ignition switch OFF.

  2. Disconnect electronic controlled engine mount control solenoid valve harness connector.

  3. Disconnect vacuum hoses connected to electronic controlled engine mount control solenoid valve.

  4. Check air passage continuity and operation delay time under the following conditions.

    Condition Air passage continuity between and

    Air passage continuity

    between and
    12 V direct current supply between terminals 1 and 2 Existed Not existed
    No supply Not existed Existed

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace electronic controlled engine mount control solenoid valve. Refer to Component Parts Location.

Fuel Injector Nissan Pathfinder 2022

Component Function Check

INSPECTION START

Turn ignition switch to START.

Are any cylinders ignited?

YES>>

GO TO 2.

NO>>

Proceed to Diagnosis Procedure.

CHECK FUEL INJECTOR FUNCTION

With CONSULT

  1. Start engine.

  2. Perform “POWER BALANCE” in “Active Test” mode of “ENGINE”.

  3. Make sure that each circuit produces a momentary engine speed drop.

Without CONSULT

  1. Start engine.

  2. Listen to each fuel injector operating sound.

    Clicking sound should be heard.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Proceed to Diagnosis Procedure.

Diagnosis Procedure

CHECK FUSE

  1. Turn ignition switch OFF.

  2. Check that the following fuse is not blowing.

    Fuse No.Capacity
    #92 15A
    #94 15A

Is the fuse blown (open)?

YES>>

Replace the fuse after repairing the applicable circuit.

NO>>

GO TO 2.

CHECK FUEL INJECTOR DRIVER POWER SUPPLY

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Turn ignition switch ON.

  4. Check the voltage between ECM harness connector and ground.

    +−Voltage
    ECM
    ConnectorTerminal
    F78 1 Ground Battery voltage
    10

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

GO TO 3.

CHECK FUEL INJECTOR DRIVER POWER SUPPLY CIRCUIT

  1. Remove fuel injector relay.

  2. Check the continuity between ECM harness connector and fuel injector relay harness connector.

    ECMFuel injector relayContinuity
    ConnectorTerminalConnectorTerminal
    F78 1 E36 10 Existed
    10 14
  3. Also check harness for short to ground.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts

CHECK FUEL INJECTOR RELAY POWER SUPPLY (CONTACTOR SIDE)

Check the voltage between fuel injector relay harness connector and ground.

+−Voltage
Fuel injector relay
ConnectorTerminal
E36 9 Ground Battery voltage
13

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Perform the trouble diagnosis for power supply circuit.

CHECK FUEL INJECTOR RELAY POWER SUPPLY (COIL SIDE)

  1. Reconnect ECM harness connector.

  2. Turn ignition switch ON.

  3. Check the voltage between fuel injector relay harness connector and ground.

    +−Voltage
    Fuel injector relay
    ConnectorTerminal
    E36 11 Ground Battery voltage
    15

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

GO TO 6.

CHECK FUEL INJECTOR RELAY POWER SUPPLY CIRCUIT (COIL SIDE)

  1. Turn ignition switch OFF.

  2. Disconnect IPDM E/R harness connector.

  3. Check the continuity between IPDM E/R harness connector and fuel injector harness connector.

    IPDM E/RFuel injector relayContinuity
    ConnectorTerminalConnectorTerminal
    F24 73 E20 11 Existed
    15
  4. Also check harness for short to ground.

Is the inspection result normal?

YES>>

Perform the trouble diagnosis for power supply circuit.

NO>>

Repair or replace error-detected parts.

CHECK FUEL INJECTOR RELAY GROUND CIRCUIT

  1. Turn ignition switch OFF.

  2. Check the continuity between fuel injector relay harness connector and ground.

    Fuel injector relay—Continuity
    ConnectorTerminal
    E36 12 Ground Existed
    16
  3. Also check harness for short to power.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair or replace error-detected parts.

CHECK FUEL INJECTOR RELAY

Check the fuel injector relay. Refer to Component Inspection (Fuel Injector Relay).

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace fuel injector relay.

CHECK ECM GROUND CIRCUIT

  1. Disconnect ECM harness connectors.

  2. Check the continuity between ECM harness connector and ground.

    ECM—Continuity
    ConnectorTerminal
    F78 3 Ground Existed
    F79 87
    E32 199
    201
    204
  3. Also check harness for short to power.

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Repair or replace error-detected parts.

CHECK FUEL INJECTOR CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between fuel injector harness connector and ECM harness connector.

    Fuel injectorECMContinuity
    CylinderConnectorTerminalConnectorTerminal
    1 F352 1 F78 12 Existed
    2 15
    2 F302 1 17
    2 14
    3 F353 1 20
    2 25
    4 F303 1 16
    2 11
    5 F354 1 13
    2 18
    6 F304 1 21
    2 24
  4. Also check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

GO TO 11.

NO>>

Repair or replace error-detected parts.

CHECK FUEL INJECTOR

Check fuel injector. Refer to Component Inspection (Fuel Injector).

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace malfunctioning fuel injector. Refer to Removal and Installation.

Component Inspection (Fuel Injector)

CHECK FUEL INJECTOR

  1. Turn ignition switch OFF.

  2. Disconnect fuel injector harness connector.

  3. Check resistance between fuel injector terminals as follows.

    Fuel injectorConditionResistance
    Terminal
    1 2 Temperature [°C (°F)] 10 – 60 (60 – 140) 1.1 – 1.9 Ω

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace malfunctioning fuel injector. Refer to Removal and Installation.

Component Inspection (Fuel Injector Relay)

CHECK FUEL INJECTOR RELAY

  1. Turn ignition switch OFF.

  2. Remove fuel injector relay.

  3. Check the continuity between fuel injector relay terminals as per the following conditions.

    Fuel injector relayConditionsContinuity
    No.Terminal
    1 9 10 12 V direct current supply between terminals 11 and 12. Existed
    No current supply Not existed
    2 13 14 12 V direct current supply between terminals 15 and 16. Existed
    No current supply Not existed

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace fuel injector relay.

Fuel Pump Nissan Pathfinder

Component Function Check

CHECK FUEL PUMP FUNCTION

  1. Turn ignition switch ON.

  2. Pinch fuel feed hose with two fingers.

    Fuel pressure pulsation should be felt on the fuel feed hose for 1 second after ignition switch is turned ON.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Diagnosis Procedure.

Diagnosis Procedure

CHECK FUEL PUMP CONTROL MODULE POWER SUPPLY

  1. Turn ignition switch OFF.

  2. Disconnect Fuel pump control module harness connector.

  3. Turn ignition switch ON.

  4. Check the voltage between Fuel pump control module harness connector and ground.

    +−Voltage
    Fuel pump control module
    ConnectorTerminal
    B58 1 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

GO TO 2.

CHECK FUEL PUMP CONTROL MODULE POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect IPDM E/R harness connector.

  3. Check the continuity between IPDM E/R harness connector and Fuel pump control module harness connector.

    IPDM E/RFuel pump control moduleContinuity
    ConnectorTerminalConnectorTerminal
    E121 46 B58 1 Existed
  4. Also check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace error-detected parts.

CHECK FUSE

Check that the following fuse is not blowing.

LocationFuse No.Capacity
IPDM E/R #85 20

Is the fuse blown (open)?

YES>>

Replace the fuse after repairing the applicable circuit.

NO>>

GO TO 4.

CHECK INTERMITTENT INCIDENT

Check intermittent incident. Refer to Intermittent Incident.

Is the inspection result normal?

YES>>

Perform trouble diagnosis for power supply circuit.

NO>>

Repair or replace error-detected parts.

CHECK FUEL PUMP CONTROL MODULE GROUND CIRCUIT

  1. Turn ignition switch OFF.

  2. Check the continuity between Fuel pump control module harness connector and ground.

    Fuel pump control module—Continuity
    ConnectorTerminal
    B58 4 Ground Existed
  3. Also check harness for short to power.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace error-detected parts.

CHECK FUEL PUMP CONTROL MODULE INPUT AND OUTPUT CIRCUITS

  1. Disconnect ECM harness connector.

  2. Check the continuity between Fuel pump control module harness connector and ECM harness connector.

    Fuel pump control moduleECMContinuity
    ConnectorTerminalConnectorTerminal
    B58 3 E32 182 Existed
    2 188
  3. Also check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair or replace error-detected parts.

CHECK FUEL PUMP CONTROL CIRCUIT

  1. Disconnect “fuel level sensor unit and fuel pump” harness connector.

  2. Check the continuity between Fuel pump control module harness connector and “fuel level sensor unit and fuel pump” harness connector.

    Fuel pump control moduleFuel level sensor unit and fuel pumpContinuity
    ConnectorTerminalConnectorTerminal
    B58 6 B57 8 Existed
    5 7

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair or replace error-detected parts.

CHECK FUEL PUMP

Check fuel pump. Refer to Component Inspection (Fuel Pump).

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Replace fuel level sensor, fuel filter and fuel pump assembly.Refer to Removal and Installation.

CHECK FUEL PUMP CONTROL MODULE

Check fuel pump control module. Refer to Component Inspection (Fuel Pump Control Module).

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace fuel pump control module.Refer to Removal and Installation.

Component Inspection (Fuel Pump)

CHECK FUEL PUMP

  1. Turn ignition switch OFF.

  2. Disconnect “fuel level sensor unit and fuel pump” harness connector.

  3. Check resistance between “fuel level sensor unit and fuel pump” terminals as follows.

    Fuel level sensor unit and fuel pumpConditionResistance
    Terminal
    4 6 Temperature [°C (°F)] 25 (77) 0.2 – 5.0 Ω

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace fuel level sensor, fuel filter and fuel pump assembly. Refer to Removal and Installation.

Component Inspection (Fuel Pump Control Module)

CHECK FUEL PUMP CONTROL MODULE

Check the voltage between fuel pump control module terminals under the following conditions.

Fuel pump control moduleCondition

Voltage

(Approx.)
Connector+−
Terminal
B58 6 5 For 1 second after turning ignition switch ON 12.9 V
More than 1 second after turning ignition switch ON 0 V
Idle speed 8.1 – 12.9 V

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace fuel pump control module. Refer to Removal and Installation.

High Pressure Fuel Pump Nissan Pathfinder

Component Function Check

CHECK HIGH PRESSURE FUEL PUMP FUNCTION

With CONSULT

  1. Start engine.

  2. On CONSULT screen, select “ENGINE”>>“Data Monitor”.

  3. Check that the “FUEL PRES SEN V” indication.

    Monitor ItemConditionValues/Status
    FUEL PRES SEN V Engine speed: Idle 1.120 – 1.310 V
    Engine speed: Revving engine from idle to 4,000 rpm quickly 1.120 – 2.900 V

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Proceed to Diagnosis Procedure.

Diagnosis Procedure

CHECK HIGH PRESSURE FUEL PUMP CIRCUIT

  1. Disconnect high pressure fuel pump relay harness connector.

  2. Check the continuity between ECM harness connector and high pressure fuel pump harness connector.

    ECMHigh pressure fuel pumpContinuity
    ConnectorTerminalConnectorTerminal
    F78 2 F96 2 Existed
    4 1
  3. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace malfunctioning part.

CHECK ECM GROUND CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between ECM harness connector and ground.

    ECM—Continuity
    ConnectorTerminal
    F78 3 Ground Existed
    F79 87
    E32 199
    201
    204
  4. Also check harness for short to power.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace malfunctioning part.

CHECK HIGH PRESSURE FUEL PUMP

Refer to Component Inspection (High Pressure Fuel Pump).

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Replace high pressure fuel pump. Refer to Removal and Installation.

CHECK HIGH PRESSURE FUEL PUMP INSTALLATION

  1. Turn ignition switch OFF.

  2. Check high pressure fuel pump for improper attachment or looseness.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace malfunctioning part.

CHECK CAMSHAFT

  1. Remove camshaft. Refer to Removal and Installation.

  2. Check camshaft. Refer to Inspection After Removal.

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace camshaft. Refer to Removal and Installation .

Component Inspection (High Pressure Fuel Pump)

CHECK HIGH PRESSURE FUEL PUMP-I

  1. Turn ignition switch OFF.

  2. Disconnect high pressure fuel pump harness connector.

  3. Check the resistance between high pressure fuel pump terminals.

    High pressure fuel pumpConditionResistance
    +−
    Terminal
    1 2 Temperature °C (°F) 20 (68) 0.45 – 0.55 Ω

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace high pressure fuel pump. Refer to Removal and Installation.

CHECK HIGH PRESSURE FUEL PUMP-II

With CONSULT

  1. Reconnect high pressure fuel pump harness connector.

  2. Start engine.

  3. On CONSULT screen, select “ENGINE”>>“Data Monitor”.

  4. Check that the “FUEL PRES SEN V” indication.

    Monitor ItemConditionValues/Status
    FUEL PRES SEN V Engine speed: Idle 1.120 – 1.310 V
    Engine speed: Revving engine from idle to 4,000 rpm quickly 1.120 – 2.900 V

Without CONSULT

  1. Reconnect high pressure fuel pump harness connector.

  2. Start engine.

  3. Check fuel rail pressure sensor signal voltage.

ECMConditionVoltage
Connector+−
Terminal
F78 47 85 Engine speed: Idle 1.12 – 1.31 V
Engine speed: Revving engine from idle to 4,000 rpm quickly 1.12 – 2.90 V

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace high pressure fuel pump. Refer to Removal and Installation.