Dtc/circuit Diagnosis (P0011 Intake Valve Timing Control ... P0111 Iat Sensor)

In this manual: Dtc/circuit Diagnosis (P0011 Intake Valve Timing Control ... P0111 Iat Sensor)
General Information — 8Engine :: Engine Mechanical — 19Engine Lubrication System - Precautions. Preparation — 1Engine Lubrication System - Lubrication System (System Description). Engine Oil Pressure (Basic Inspection). Service Data and Specifications (SDS) — 1Engine Cooling System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Engine Cooling System - Engine Coolant — 1Engine Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Engine Control System - Ecu Diagnosis Information — 1Ecu Diagnosis Information - Ecm ++ — 1Engine Control System - Basic Inspection — 1Basic Inspection - Diagnosis and Repair Workflow ++ — 1Basic Inspection - Basic Inspection ++ — 1Basic Inspection - Additional Service When Replacing Ecm ++ — 1Basic Inspection - Fuel Pressure Check ++ — 1Basic Inspection - How to Set Srt Code ++ — 1Basic Inspection - How to Erase Permanent Dtc ++ — 1Engine Control System - Dtc/circuit Diagnosis — 1Engine Control System - Symptom Diagnosis — 1Engine Control System - Periodic Maintenance — 1Engine Control System - Removal and Installation — 1Fuel System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Fuel System - Fuel System (Periodic Maintenance). Fuel Level Sensor Unit (Disassembly and Assembly) — 1Exhaust System - Precautions. Preparation — 1Exhaust System - Exhaust System (Periodic Maintenance). Exhaust System (Removal and Installation) — 1Starting System - Precautions. Preparation. Starter Motor (Service Data and Specifications (sds)) — 1Starting System - Diagnosis and Repair Work Flow — 1Starting System - Starting System (Symptom Diagnosis). Starter Motor (Removal and Installation) — 1Accelerator Control System - Precautions. Service Data and Specifications (SDS) — 1Accelerator Control System - Accelerator Pedal Assembly — 1Transmission & Driveline :: Transaxle & Transmission — 21Driveline - System Description — 1Transfer: Ty92b - Ecu Diagnosis Information. Awd Control Unit ++ — 1Driveline - Basic Inspection — 1Driveline - Dtc/circuit Diagnosis — 1Driveline - Symptom Diagnosis — 1Driveline - Removal and Installation — 1Transfer: Ty92b - Unit Removal and Installation. Transfer Assembly ++ — 1Driveline - Unit Disassembly and Assembly — 1Driveline - Basic Inspection — 1Driveline - Removal and Installation — 1Driveline - Unit Disassembly and Assembly — 1Front Axle - Precautions. Preparation — 1Front Axle - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Front Axle - Front Drive Shaft Boot — 1Front Axle - Front Drive Shaft — 1Rear Axle - Precautions. Preparation. Service Data and Specifications (SDS) — 1Rear Axle - Noise, Vibration and Harshness (nvh) Troubleshooting — 1Rear Axle - Rear Drive Shaft — 1Suspension :: Front Suspension — 7Rear Suspension - Precautions. Preparation — 1Rear Suspension - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Rear Suspension - Rear Suspension Assembly — 1Road Wheels & Tires - Precautions — 1Road Wheels & Tires - Preparation. Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Road Wheels & Tires - System — 1Brakes :: Brake System — 9Parking Brake System - Precautions. Preparation — 1Parking Brake System - System — 1Vdc/tcs/abs - Precautions ++ — 1Brake Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Dtc/circuit Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Steering :: Steering System — 9Steering Control System - Precautions — 1Steering Control System - System — 1Steering Control System - Eps Control Unit (Ecu Diagnosis Information. Removal and Installation) — 1Restraints :: Seat Belt — 7Srs Air Bag - Precautions. Preparation — 1Srs Air Bag - Collision Diagnosis — 1Srs Air Bag - Occupant Classification System — 1Srs Air Bag Control System - Precautions — 1Srs Air Bag Control System - System — 1Srs Air Bag Control System - Diagnosis Sensor Unit — 1Srs Air Bag Control System - Inspection and Adjustment — 1Ventilation, Heater & Air Conditioner :: Ventilation System — 6Heater & Air Conditioning System - Precautions — 1Heater & Air Conditioning System - Preparation — 1Heater & Air Conditioning System - Component Parts — 1Heater & Air Conditioning System - Diagnosis and Repair Work Flow — 1Heater & Air Conditioning System - Compressor — 1Heater & Air Conditioning System - Cooler Pipe and Hose — 1Heater & Air Conditioning System - Condenser. Condenser — 1Heater & Air Conditioning System - Heating and Cooling Unit Assembly — 1Heater & Air Conditioning System - Service Data and Specifications (SDS) — 1Heater & Air Conditioning Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1Heater & Air Conditioning Control System - Ecu Diagnosis Information — 1Heater & Air Conditioning Control System - Basic Inspection — 1Heater & Air Conditioning Control System - Dtc/circuit Diagnosis — 1Heater & Air Conditioning Control System - Symptom Diagnosis — 1Heater & Air Conditioning Control System - Removal and Installation — 1Body Interior :: Interior — 8Instrument Panel - Precautions. Preparation. Clip List — 1Instrument Panel - Squeak and Rattle Trouble Diagnoses — 1Instrument Panel - Cluster Lid C — 1Seat - Precautions — 1Seat - Preparation. Clip List — 1Seat - Component Parts — 1Seat - System — 1Seat - Diagnosis and Repair Work Flow — 1Seat - Front Seat — 1Seat - Second Row Seats — 1Seat - Third Row Seats — 1Seat - Front Seat — 1Seat - Second Row Seat — 1Seat - Third Row Seat — 1Automatic Drive Positioner - Precautions. Preparation — 1Automatic Drive Positioner - System — 1Automatic Drive Positioner - Diagnosis and Repair Work Flow — 1Automatic Drive Positioner - Inspection and Adjustment — 1Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock — 38Security Control System - Precautions — 1Security Control System - System — 1Security Control System - Ecm, Bcm, Intelligent Key Unit, Ipdm E/r — 1Security Control System - Vehicle Security System Cannot Be Set — 1Glass & Window System - Precautions. Preparation — 1Glass & Window System - Squeak and Rattle Trouble Diagnoses — 1Power Window Control System - Precautions. Preparation — 1Power Window Control System - Power Supply and Ground Circuit — 1Power Window Control System - Power Window Motor Circuit — 1Power Window Control System - Front Power Window Rh Alone Does Not Operate — 1Power Window Control System - Rear Lh Side Power Window Alone Does Not Operate — 1Power Window Control System - Rear Rh Side Power Window Alone Does Not Operate — 1Roof - Precautions. Preparation — 1Roof - Power Supply and Ground Circuit — 1Roof - Moonroof Switch Assembly — 1Roof - Lin Communication Circuit — 1Roof - Auto Operation Does Not Operate — 1Roof - Anti-Pinch Function Does Not Operate — 1Exterior - Precautions. Preparation. Clip List (Preparation) — 1Exterior - Squeak and Rattle Trouble Diagnoses — 1Exterior - Fender Protector — 1Exterior - Over Fender — 1Exterior - Under Cover — 1Exterior - Roof Side Rail — 1Body Repair - Service Information — 1Service Information - Sheet Metal Work ++ — 1Service Information - Body Welding and Precautions ++ — 1Service Information - Safety and Health ++ — 1Service Information - Repairing Procedures and Precautions ++ — 1Body Repair - Precaution — 1Body Repair - Preparation — 1Body Repair - Removal and Installation — 1Driver Controls :: Mirrors — 8Exterior Lighting System - System Description — 1System Description - Component Parts ++ — 1Exterior Lighting System - Basic Inspection — 1Exterior Lighting System - Dtc/circuit Diagnosis — 1Exterior Lighting System - Symptom Diagnosis — 1Exterior Lighting System - Periodic Maintenance — 1Exterior Lighting System - Removal and Installation — 1Interior Lighting System - Precautions. Preparation — 1Interior Lighting System - Component Parts. Interior Lighting System — 1Interior Lighting System - System — 1Interior Lighting System - Diagnosis and Repair Work Flow — 1Interior Lighting System - Interior Lighting System Symptoms (Symptom Diagnosis). Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Interior Lighting System - Foot Lamp — 1Wiper & Washer - Precautions — 1Wiper & Washer - Preparation. Bcm, Ipdm E/r (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Wiper & Washer - System — 1Wiper & Washer - Diagnosis and Repair Work Flow — 1Defogger - Precautions. Bcm, A/c Auto Amp. (Ecu Diagnosis Information) — 1Defogger - Diagnosis and Repair Work Flow — 1Horn - Precautions — 1Electrical & Power Control :: Power Outlet — 13Body Control System - Precautions. Preparation — 1Body Control System - Component Parts — 1Body Control System - System — 1Body Control System - Diagnosis System (bcm) — 1Body Control System - Bcm — 1Lan System - System Description — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - Removal and Installation — 1Charging System - Precautions. Preparation. Ecm, Ipdm E/r (Ecu Diagnosis Information) — 1Charging System - Diagnosis and Repair Work Flow — 1Charging System - Charging System (Symptom Diagnosis). Generator (Removal and Installation). Service Data and Specifications (SDS) — 1Power Supply, Ground & Circuit Elements - Precautions. Preparation. Service Data and Specifications (SDS) — 1Driver Information & Multimedia :: Meter, Warning Lamp & Indicator — 25Warning Chime System - Application Notice (How to Use This Manual). Precautions — 1Warning Chime System - System — 1Warning Chime System - Diagnosis System (combination Meter) — 1Warning Chime System - Bcm, Combination Meter (Ecu Diagnosis Information). Diagnosis and Repair Work Flow (Basic Inspection) — 1Sonar System - Precautions. Preparation — 1Sonar System - Sonar Control Unit — 1Dtc/circuit Diagnosis - B2720 Corner Sensor [rl] ++ — 1Audio, Visual & Navigation System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Multi Av (av Control Unit) ++ — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Symptom Diagnosis - Multi Av System ++ — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Cruise Control & Driver Assistance :: Cruise Control System — 17Driver Assistance System - System Description — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Driver Assistance System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1System Description - Handling Precaution ++ — 1Driver Assistance System - Ecu Diagnosis Information — 1Driver Assistance System - Basic Inspection — 1Basic Inspection - Distance Sensor Alignment ++ — 1Basic Inspection - Camera Aiming Adjustment ++ — 1Basic Inspection - Action Test ++ — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Laser/radar (distance Sensor) ++ — 1Dtc/circuit Diagnosis - Lane Camera (front Camera Unit) ++ — 1Driver Assistance System - Symptom Diagnosis — 1Driver Assistance System - Removal and Installation — 1Driver Assistance System - System Description — 1System Description - System ++ — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Drive Mode System - Precautions — 1Drive Mode System - Component Parts. Drive Mode System — 1Drive Mode System - System — 1Drive Mode System - Diagnosis and Repair Work Flow — 1Drive Mode System - Drive Mode Select Switch Circuit — 1Maintenance - Precautions. Preparation — 1Maintenance - General Maintenance — 1Maintenance - Periodic Maintenance — 1Maintenance - Recommended Fluids and Lubricants — 1Maintenance - Engine Maintenance — 1Maintenance - Chassis and Body Maintenance — 1Engine Lubrication System - Periodic Maintenance — 1Engine Lubrication System - Removal and Installation — 1Engine Cooling System - System Description — 1Engine Cooling System - Removal and Installation — 1Engine Control System - Vq35dd — 1Fuel System - Removal and Installation — 1Starting System - System Description — 1Starting System - Dtc/circuit Diagnosis — 1Driveline - Transfer: Ty92b — 1Driveline - Rear Propeller Shaft: 3fcj-Cvj — 1Driveline - Rear Final Drive: R145 — 1Front Axle - Periodic Maintenance — 1Front Axle - Removal and Installation — 1Rear Axle - Periodic Maintenance — 1Rear Axle - Removal and Installation — 1Rear Suspension - Removal and Installation — 1Road Wheels & Tires - System Description — 1Road Wheels & Tires - Basic Inspection — 1Road Wheels & Tires - Dtc/circuit Diagnosis — 1Road Wheels & Tires - Symptom Diagnosis — 1Road Wheels & Tires - Periodic Maintenance — 1Road Wheels & Tires - Removal and Installation — 1Parking Brake System - System Description — 1Parking Brake System - Basic Inspection — 1Parking Brake System - Dtc/circuit Diagnosis — 1Parking Brake System - Symptom Diagnosis — 1Parking Brake System - Removal and Installation — 1Brake Control System - Vdc/tcs/abs — 1Brake Control System - Automatic Brake Hold — 1Brake Control System - Automatic Emergency Braking — 1Brake Control System - Rear Automatic Braking — 1Steering Control System - System Description — 1Steering Control System - Basic Inspection — 1Steering Control System - Dtc/circuit Diagnosis — 1Steering Control System - Symptom Diagnosis — 1Srs Air Bag - Removal and Installation — 1Srs Air Bag Control System - System Description — 1Srs Air Bag Control System - Basic Inspection — 1Srs Air Bag Control System - Symptom Diagnosis — 1Heater & Air Conditioning System - Symptom Diagnosis — 1Heater & Air Conditioning System - Periodic Maintenance — 1Heater & Air Conditioning Control System - Automatic Air Conditioning — 1Instrument Panel - Removal and Installation — 1Instrument Panel - Unit Disassembly and Assembly — 1Seat - Ecu Diagnosis Information — 1Seat - Dtc/circuit Diagnosis — 1Seat - Symptom Diagnosis — 1Automatic Drive Positioner - System Description — 1Automatic Drive Positioner - Ecu Diagnosis Information — 1Automatic Drive Positioner - Dtc/circuit Diagnosis — 1Automatic Drive Positioner - Symptom Diagnosis — 1Automatic Drive Positioner - Removal and Installation — 1Security Control System - System Description — 1Security Control System - Basic Inspection — 1Security Control System - Dtc/circuit Diagnosis — 1Security Control System - Symptom Diagnosis — 1Security Control System - Removal and Installation — 1Glass & Window System - Removal and Installation — 1Power Window Control System - System Description — 1Power Window Control System - Ecu Diagnosis Information — 1Power Window Control System - Basic Inspection — 1Power Window Control System - Dtc/circuit Diagnosis — 1Power Window Control System - Symptom Diagnosis — 1Power Window Control System - Removal and Installation — 1Roof - System Description — 1Roof - Ecu Diagnosis Information — 1Roof - Basic Inspection — 1Roof - Dtc/circuit Diagnosis — 1Roof - Symptom Diagnosis — 1Roof - Removal and Installation — 1Exterior - System Description — 1Exterior - Removal and Installation — 1Body Repair - Repair Information — 1Exterior Lighting System - Led Headlamp — 1Interior Lighting System - Dtc/circuit Diagnosis — 1Interior Lighting System - Removal and Installation — 1Wiper & Washer - System Description — 1Wiper & Washer - Dtc/circuit Diagnosis — 1Wiper & Washer - Symptom Diagnosis — 1Wiper & Washer - Removal and Installation — 1Defogger - System Description — 1Defogger - Dtc/circuit Diagnosis — 1Defogger - Symptom Diagnosis — 1Defogger - Removal and Installation — 1Horn - Removal and Installation — 1Body Control System - Basic Inspection — 1Body Control System - Dtc/circuit Diagnosis — 1Body Control System - Symptom Diagnosis — 1Body Control System - Removal and Installation — 1Lan System - Can Fundamental — 1Lan System - Can — 1Lan System - Can Gateway — 1Power Control System - Ipdm E/r — 1Power Control System - Power Distribution System — 1Charging System - System Description — 1Charging System - Dtc/circuit Diagnosis — 1Power Supply, Ground & Circuit Elements - System Description — 1Power Supply, Ground & Circuit Elements - Basic Inspection — 1Power Supply, Ground & Circuit Elements - Removal and Installation — 1Warning Chime System - System Description — 1Warning Chime System - Dtc/circuit Diagnosis — 1Warning Chime System - Symptom Diagnosis — 1Sonar System - System Description — 1Sonar System - Basic Inspection — 1Sonar System - Dtc/circuit Diagnosis — 1Sonar System - Symptom Diagnosis — 1Sonar System - Removal and Installation — 1Audio, Visual & Navigation System - Nissanconnect — 1Audio, Visual & Navigation System - Intelligent Around View Monitor System — 1Audio, Visual & Navigation System - Rear View Monitor System — 1Audio, Visual & Navigation System - Telematics System — 1Driver Assistance System - Adas Control Unit 2 — 1Driver Assistance System - Driver Assistance System — 1Driver Assistance System - Chassis Control — 1Drive Mode System - Removal and Installation — 1Dtc/circuit Diagnosis (C053c Wheel Speed Sensor ... U2141 Can Comm Circuit) — 1Dtc/circuit Diagnosis (P0011 Intake Valve Timing Control ... P0111 Iat Sensor) — 1Dtc/circuit Diagnosis (P0116 Engine Coolant Temperature Sensor ... P025b Fuel Pump Module a) — 1Dtc/circuit Diagnosis (P026b Injection Timing ... P0420 Three Way Catalyst Function) — 1Dtc/circuit Diagnosis (P0441 Evap Control System ... P0524 Engine Oil Pressure) — 1Dtc/circuit Diagnosis (P0532 A/c Refrigerant Pressure Sensor ... P064d Ecm) — 1Dtc/circuit Diagnosis (P06da Engine Oil Pressure Control Solenoid Valve ... P1217 Engine Over Temperature) — 1Dtc/circuit Diagnosis (P1220 Fuel Pump Control Module (fpcm) ... P1574 Ascd Vehicle Speed Sensor) — 1Dtc/circuit Diagnosis (P1575 Brake Switch ... P2101 Electric Throttle Control Function) — 1Dtc/circuit Diagnosis (P2118 Throttle Control Motor ... P34ac Electric Intake Valve Timing Control Actuator) — 1Dtc/circuit Diagnosis (Active Grille Shutter ... High Pressure Fuel Pump) — 1Dtc/circuit Diagnosis (Ignition Signal ... Variable Induction Air System) — 14012 C1040 Emergency Brake — 14013 C106a Wheel Sensor — 14014 C1078-55 Not Configuration — 14015 C10b4-98 Overheat — 14016 B1001 Lap Pre-Tensioner Lh — 14017 B0001 Driver Air Bag Module — 14018 B100e Knee Air Bag Module Rh — 14019 B142x Collision Detection — 1Dtc/circuit Diagnosis (B20c7-11 A/c Clutch ... B24a6-11 in-Vehicle Sensor) — 1Dtc/circuit Diagnosis (B24a6-15 in-Vehicle Sensor ... U2140-87 Can Comm Err (ecm)) — 1Dtc/circuit Diagnosis (C1f00-1c Control Unit ... C1f04-61 Brake Sw/stop Lamp Sw) — 1Dtc/circuit Diagnosis (C1f05-49 Front Camera Unit ... C1f70-87 Ethernet Circuit) — 1
208steps
~1248min
5/5difficulty
Done 0 of 208
  • P0011 Intake Valve Timing Control
  • P0014 Evt Control
  • P0030 A/f Sensor 1 Heater
  • P0078 Evt Control Solenoid Valve
  • P0087 Frp Control System ➤
  • P00d2 Ho2s2 Heater
  • P00fe Evap Control System
  • P0101 Maf Sensor
  • P0107 Barometric Pressure Sensor
  • P0111 Iat Sensor

P0011 Intake Valve Timing Control Nissan Pathfinder 5th Gen

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0011 00

INT/V TIM CONT-B1

[Intake valve timing control performance (bank 1)]
A Diagnosis condition
  • Ignition switch: ON

  • Engine speed: 1,200 – 3,175 rpm

  • Engine coolant temperature: 60 – 120 °C

  • Battery voltage: 11 – 16 V

Signal (terminal) —
Threshold During the advanced control of intake valve timing control, the angle difference between actual angle and target angle is 13 degrees or more
Diagnosis delay time 6 seconds
B Diagnosis condition
  • Ignition switch: ON

  • Engine speed: 500 – 2,000 rpm [when Nissan Pathfinder vehicle speed is less than 4 km/h]

  • Engine speed: 1,200 – 2,000 rpm [when vehicle speed is 4 km/h or more]

  • Engine coolant temperature: 60 – 120 °C

  • Battery voltage: 11 – 16 V

Signal (terminal) —
Threshold During the advanced control of intake valve timing control, the absolute difference between valve timing control reference position and base angle is 13 degrees or more
Diagnosis delay time 3 seconds

POSSIBLE CAUSE

Malfunction A

  • Electric intake valve timing (IVT) control actuator (bank 1)

  • Harness and connectors (Electric IVT control actuator (bank 1) motor control circuit is open or shorted.)

  • Foreign matter caught at the electric IVT control actuator (bank 1)

Malfunction B

  • Timing chain installation

  • Intake camshaft sprocket (bank 1) wear

FAIL-SAFE

Fail safe modeNissan Pathfinder Vehicle behavior
Device fix mode
  • Fixes electric intake valve timing control motor in the reference position.

  • Fixes exhaust valve timing control solenoid valve in the reference position.

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is between 11 V and 16 V at idle.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE-I

With CONSULT

  1. Turn ignition switch ON.

  2. On CONSULT screen, select “ENGINE”>>“Data Monitor”.

  3. Start engine and warm it up to the normal operating temperature.

  4. Maintain the following conditions for at least 10 consecutive seconds. Hold the accelerator pedal as steady as possible.

    ENG SPEED 1,200 – 2,000 rpm
    COOLAN TEMP/S More than 60 °C
    Selector lever P or N position
  5. Let engine idle for 10 seconds.

  6. Check 1st trip DTC.

With GST

Follow the procedure “With CONSULT” above.

Is DTC P0011 detected?

YES>>

Proceed to Diagnosis Procedure.

NO>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE-II

With CONSULT

  1. Maintain the following conditions for at least 20 consecutive seconds.

    ENG SPEED 1,200 – 3,175 rpm (A constant rotation is maintained.)
    COOLAN TEMP/S More than 64 °C
    Selector lever 1st or 2nd position
    Driving location

    Driving Nissan Pathfinder vehicle uphill

    (Increased engine load will help maintain the driving conditions required for this test.)
  2. Check 1st trip DTC.

WITH GST

Follow the procedure “With CONSULT” above.

Is DTC P0011 detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

TYPE A

CHECK ELECTRIC IVT CONTROL ACTUATOR (BANK 1) MOTOR CONTROL CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect electric IVT control actuator (bank 1) harness connector and electric IVT control module harness connector.

  3. Check the continuity between electric IVT control actuator (bank 1) harness connector and electric IVT control module harness connector.

    Electric IVT control actuator (bank 1)Electric IVT control moduleContinuity
    ConnectorTerminalConnectorTerminal
    F87 1 F99 117 Existed
    2 114
    3 119
  4. Check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

Replace electric IVT control actuator (bank 1). Refer to Exploded View.

NO>>

Repair or replace error-detected parts.

TYPE B

CHECK TIMING CHAIN INSTALLATION

Check service records for any recent repairs that may cause timing chain misaligned.

Are there any service records that may cause timing chain misaligned?

YES>>

Check timing chain installation. Refer to Removal and Installation.

NO>>

GO TO 2.

CHECK CAMSHAFT SPROCKET AND TIMING CHAIN

Check the following.

  1. Visually check for chipping camshaft sprocket (bank 1) gear tooth.

  2. timing chain tension and elongation.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Repair or replace error-detected parts.

P0014 Evt Control Nissan Pathfinder 2026

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0014 00

EXH/V TIM CONT-B1

(“B” camshaft position - timing over-advanced or system performance bank 1)
Diagnosis condition
  • Ignition switch: ON

  • Engine speed: 1,700 – 2,950 rpm

  • Engine coolant temperature: 70 – 120 °C

  • Battery voltage: 11 – 16 V

Signal (terminal) —
Threshold During the advanced control of exhaust valve timing control, the angle difference between actual angle and target angle is 13 degrees or more
Diagnosis delay time 6 seconds or more

POSSIBLE CAUSE

  • Crankshaft position sensor 1

  • Exhaust camshaft position sensor

  • Exhaust valve control solenoid valve

  • Accumulation of debris to the signal pick-up portion of the camshaft

  • Timing chain installation

  • Foreign matter caught in the oil groove for exhaust valve timing control

FAIL-SAFE

Fail safe mode Nissan Pathfinder Vehicle behavior
Device fix mode
  • Fixes electric intake valve timing control motor in the reference position.

  • Fixes exhaust valve timing control solenoid valve in the reference position.

DTC Confirmation Procedure

CHECK DTC PRIORITY

If DTC P0014 is displayed with DTC P0078, first perform the confirmation procedure (trouble diagnosis) for DTC P0078.

Is DTC P0078 detected?

YES>>

Perform diagnosis for P0078. Refer to DTC Description.

NO>>

GO TO 2.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is between 10 V and 16 V at idle.

>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE-I

With CONSULT

  1. Turn ignition switch ON.

  2. On CONSULT screen, select “ENGINE”>>“Data Monitor”.

  3. Start engine and warm it up to the normal operating temperature.

  4. Maintain the following conditions for at least 6 consecutive seconds. Hold the accelerator pedal as steady as possible.

    ENG SPEED 1,200 – 2,000 rpm (A constant rotation is maintained.)
    COOLAN TEMP/S More than 60 °C
    Selector lever P or N position
  5. Let engine idle for 10 seconds.

  6. Check 1st trip DTC.

With GST

Follow the procedure “With CONSULT” above.

Is DTC P0014 detected?

YES>>

Proceed to Diagnosis Procedure.

NO>>

GO TO 4.

PERFORM DTC CONFIRMATION PROCEDURE-II

With CONSULT

  1. Maintain the following conditions for at least 20 consecutive seconds.

    ENG SPEED 1,700 – 2,950 rpm (A constant rotation is maintained.)
    COOLAN TEMP/S More than 70 °C
    Selector lever D position
    Driving location uphill

    Driving Nissan Pathfinder vehicle uphill

    (Increased engine load will help maintain the driving conditions required for this test.)
  2. Check 1st trip DTC.

With GST

Follow the procedure “With CONSULT” above.

Is DTC P0014 detected?

YES>>

Proceed to Diagnosis Procedure

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P0014 is displayed with DTC P0078, first perform the confirmation procedure (trouble diagnosis) for DTC P0078.

Is DTC P0078 detected?

YES>>

Perform diagnosis for P0078. Refer to DTC Description.

NO>>

GO TO 2.

CHECK OIL PRESSURE WARNING

  1. Start engine.

  2. Check oil pressure warning and confirm it is not displayed.

Is oil pressure warning displayed?

YES>>

Check the engine oil level. Refer to Inspection.

NO>>

GO TO 3.

CHECK EXHAUST VALVE TIMING CONTROL SOLENOID VALVE

Check the exhaust valve timing control solenoid valve. Refer to Component Inspection (Exhaust Valve Timing Control Solenoid Valve).

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Replace malfunctioning exhaust valve timing control solenoid valve. Refer to Exploded View.

CHECK CRANKSHAFT POSITION SENSOR 1

Check the crankshaft position sensor 1. Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Replace crankshaft position sensor 1. Refer to Exploded View.

CHECK EXHAUST CAMSHAFT POSITION SENSOR

Check the exhaust camshaft position sensor. Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Replace malfunctioning exhaust camshaft position sensor. Refer to Exploded View.

CHECK CAMSHAFT (EXH)

Check the following.

  • Accumulation of debris to the signal plate of camshaft rear end

  • Chipping signal plate of camshaft rear end

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Remove debris and clean the signal plate of camshaft rear end or replace camshaft. Refer to Removal and Installation.

CHECK TIMING CHAIN INSTALLATION

Check service records for any recent repairs that may cause timing chain misaligned.

Are there any service records that may cause timing chain misaligned?

YES>>

Check timing chain installation. Refer to Removal and Installation.

NO>>

GO TO 8.

CHECK LUBRICATION CIRCUIT

Refer to Inspection.

Is the inspection result normal?

YES>>

INSPECTION END.

NO>>

Clean lubrication line.

Component Inspection (Exhaust Valve Timing Control Solenoid Valve)

CHECK EXHAUST VALVE TIMING CONTROL SOLENOID VALVE-I

  1. Turn ignition switch OFF.

  2. Disconnect exhaust valve timing control solenoid valve harness connector.

  3. Check resistance between exhaust valve timing control solenoid valve terminals as per the following.

    Exhaust valve timing control solenoid valve

    Condition

    Resistance
    Terminal
    1 2 Temperature [°C (°F)] 20 (68) 7.0 – 7.8 Ω
    1 Ground

    ∞Ω

    (Continuity should not exist)
    2

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace malfunctioning exhaust valve timing control solenoid valve. Refer to Exploded View.

CHECK EXHAUST VALVE TIMING CONTROL SOLENOID VALVE-II

  1. Remove exhaust valve timing control solenoid valve. Refer to Exploded View.

  2. Provide 12 V DC between exhaust valve timing control solenoid valve terminals 1 and 2, and then interrupt it. Check that the plunger moves as shown in the figure.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace malfunctioning exhaust valve timing control solenoid valve. Refer to Exploded View.

P0030 A/f Sensor 1 Heater Nissan Pathfinder

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0030 00

HO2S1 HTR B1

(HO2S heater control circuit bank 1 sensor 1)
Diagnosis condition Engine running at idle
Signal (terminal) A/F sensor 1 heater (bank 1) signal
Threshold

Deterioration in A/F sensor 1 heater performance.

(Voltage signal transmitted from A/F sensor 1 heater to ECM is higher/lower than voltage in the normal range.)
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors [A/F sensor 1 heater (bank 1) circuit is open or shorted.]

  • A/F sensor 1 heater (bank 1)

  • Short circuit of harness between the air fuel ratio (A/F) sensor 1 and heated oxygen sensor 2.

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

CHECK DTC PRIORITY

When DTC P0030 is detected with DTC P0036, first perform to check the harness for short circuit between the heated oxygen sensor 2 and the air fuel ratio (A/F) sensor 1.

Is applicable DTC detected?

YES>>

Perform to check the harness for short circuit between the heated oxygen sensor 2 and the air fuel ratio (A/F) sensor 1.

NO>>

GO TO 2.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Ignition switch OFF and wait at least 10 seconds.

  2. Ignition switch ON.

  3. Ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is between 10.5 V and 16 V at idle.

>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and let it idle for at least 10 seconds.

  2. Check 1st trip DTC.

Is DTC P0030 detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

Proceed to Diagnosis Procedure.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK AIR FUEL RATIO (A/F) SENSOR 1 CONNECTOR FOR CONNECTION-1

Push the connector of air fuel ratio (A/F) sensor 1 and check it for connection.

Is the connector connected securely?

YES>>

GO TO 2.

NO>>

After connecting connector securely perform DTC confirmation procedure again. Refer to DTC Confirmation Procedure.

CHECK AIR FUEL RATIO (A/F) SENSOR 1 CONNECTOR INSIDE

Disconnect the air fuel ratio (A/F) sensor 1 connector and check inside the connector for water or foreign material.

Is inspection result normal?

YES>>

GO TO 3.

NO>>

Replace A/F sensor 1. Refer to Exploded View.

CHECK AIR FUEL RATIO (A/F) SENSOR 1 CONNECTOR FOR CONNECTION-2

Reconnect securely the connector of air fuel ratio (A/F) sensor 1 and check it for connection.

Is the connector connected securely?

YES>>

GO TO 4.

NO>>

Repair the harness connector and replace the air fuel ratio (A/F) sensor 1. Refer to Exploded View.

CHECK A/F SENSOR 1 POWER SUPPLY

  1. Ignition switch OFF.

  2. Disconnect A/F sensor 1 harness connector.

  3. Ignition switch ON.

  4. Check the voltage between A/F sensor 1 harness connector and ground.

    +−Voltage
    A/F sensor 1
    BankConnectorTerminal
    1 F72 1 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

GO TO 5.

CHECK IPDM E/R POWER SUPPLY AND GROUND CIRCUIT

Check IPDM E/R power supply and ground circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace malfunctioning part.

CHECK A/F SENSOR 1 POWER SUPPLY CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect IPDM E/R harness connector.

  3. Check the continuity between IPDM E/R harness connector and A/F sensor 1 harness connector.

    IPDM E/RA/F sensor 1Continuity
    ConnectorTerminalConnectorTerminal
    F24 75 F72 1 Existed
  4. Also check harness for short to ground.

Is the inspection result normal?

YES>>

Perform the trouble diagnosis for power supply circuit.

NO>>

Repair or replace error-detected parts.

CHECK A/F SENSOR 1 HEATER OUTPUT SIGNAL CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between A/F sensor 1 harness connector and ECM harness connector.

    A/F sensor 1ECMContinuity
    BankConnectorTerminalConnectorTerminal
    1 F72 2 F79 91 Existed
  4. Also check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair or replace error-detected parts.

CHECK A/F SENSOR 1 HEATER

Check A/F sensor 1 heater. Refer to Component Inspection (A/F Sensor 1 Heater).

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Replace malfunctioning A/F sensor 1. Refer to Exploded View.

Component Inspection (A/F Sensor 1 Heater)

CHECK A/F SENSOR 1

  1. Ignition switch OFF.

  2. Disconnect A/F sensor 1 harness connector.

  3. Check resistance between A/F sensor 1 terminals as follows.

    A/F sensor 1

    Condition

    Resistance
    Terminal
    1 2 Temperature 25 °C 1.80 – 2.44 Ω
    3

    ∞Ω

    (Continuity should not exist)
    4
    2 3
    4
    3 4

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace malfunctioning A/F sensor 1. Refer to Exploded View.

P0078 Evt Control Solenoid Valve Nissan Pathfinder R53

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0078 00

EX V/T ACT/CIRC-B1

(Exhaust valve control solenoid circuit bank 1)
Diagnosis condition Engine running at idle
Signal (terminal) Exhaust valve timing control solenoid valve (bank 1) signal
Threshold An improper voltage is sent to the ECM through exhaust valve timing control solenoid valve
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors (Exhaust valve timing control solenoid valve circuit is open or shorted.)

  • Exhaust valve timing control solenoid valve

FAIL-SAFE

Fail safe modeNissan Pathfinder Vehicle behavior
Device fix mode
  • Fixes electric intake valve timing control motor in the reference position.

  • Fixes exhaust valve timing control solenoid valve in the reference position.

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and let it idle for 5 seconds.

  2. Check 1st trip DTC.

Is DTC P0078 detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK EXHAUST VALVE TIMING CONTROL SOLENOID VALVE POWER SUPPLY

  1. Turn ignition switch OFF.

  2. Disconnect exhaust valve timing control solenoid valve harness connector.

  3. Turn ignition switch ON.

  4. Check the voltage between exhaust valve timing control solenoid valve harness connector and ground.

    +−Voltage
    Exhaust valve timing control solenoid valve
    BankConnectorTerminal
    1 F77 1 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 2.

CHECK EXHAUST VALVE TIMING CONTROL SOLENOID VALVE POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect IPDM E/R harness connector.

  3. Check the continuity between exhaust valve timing control solenoid valve harness connector and IPDM E/R harness connector.

    Exhaust valve timing control solenoid valveIPDM E/RContinuity
    BankConnectorTerminalConnectorTerminal
    1 F77 1 F24 73 Existed
  4. Also check harness for short to ground.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Repair or replace error-detected parts.

CHECK EXHAUST VALVE TIMING CONTROL SOLENOID VALVE OUTPUT SIGNAL CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between exhaust valve timing control solenoid valve harness connector and ECM harness connector.

    Exhaust valve timing control solenoid valveECMContinuity
    BankConnectorTerminalConnectorTerminal
    1 F77 2 F79 157 Existed
  4. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts.

CHECK EXHAUST VALVE TIMING CONTROL SOLENOID VALVE

Check exhaust valve timing control solenoid valve control solenoid valve. Refer to Component Inspection (Exhaust Valve Timing Control Solenoid Valve).

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace malfunctioning exhaust valve timing control solenoid valve. Refer to Exploded View.

Component Inspection (Exhaust Valve Timing Control Solenoid Valve)

CHECK EXHAUST VALVE TIMING CONTROL SOLENOID VALVE-I

  1. Turn ignition switch OFF.

  2. Disconnect exhaust valve timing control solenoid valve harness connector.

  3. Check resistance between exhaust valve timing control solenoid valve terminals as per the following.

    Exhaust valve timing control solenoid valve

    Condition

    Resistance
    Terminal
    1 2 Temperature [°C (°F)] 20 (68) 7.0 – 7.8 Ω
    1 Ground

    ∞Ω

    (Continuity should not exist)
    2

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace malfunctioning exhaust valve timing control solenoid valve. Refer to Exploded View.

CHECK EXHAUST VALVE TIMING CONTROL SOLENOID VALVE-II

  1. Remove exhaust valve timing control solenoid valve. Refer to Exploded View.

  2. Provide 12 V DC between exhaust valve timing control solenoid valve terminals 1 and 2, and then interrupt it. Check that the plunger moves as shown in the figure.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace malfunctioning exhaust valve timing control solenoid valve. Refer to Exploded View.

P0087 Frp Control System ➤ Nissan Pathfinder 2022

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0087 00

LOW FUEL PRES

(Fuel rail/system pressure - too low)
A Diagnosis condition Engine running at idle
Signal (terminal) Fuel rail pressure signal
Threshold
  • Fuel rail pressure does not reach 4.0 MPa (40.8 kg/cm2, 580 psi) at engine cold start [water temperature −12 °C – 40 °C].

  • Fuel rail pressure remains at 7.5 MPa (76.5 kg/cm2, 1087.5 psi) or less for 1 second or more during engine idle condition after cold start [water temperature −12 °C – 40 °C].

  • The following condition continues for 5 seconds or more after engine start (regardless of water temperature): Target fuel pressure – Actual fuel pressure = 2.7 MPa (27.5 kg/cm2, 392 psi) or less.

Diagnosis delay time 5 seconds or more

POSSIBLE CAUSE

  • Fuel system

  • Leakage in fuel line

  • High pressure fuel pump

  • Low pressure fuel pump

  • Damage in lifter

  • Out of gas

  • Harness or connector

  • Fuel Pressure sensor

  • Fuel Injector stuck open

  • Clogged in fuel line

  • High Pressure fuel pump cam and lifter

FAIL-SAFE

Fail safe mode Nissan Pathfinder Vehicle behavior
Traveling control mode Accelerator angle variation control

ECM controls the accelerator pedal depression speed to make it slower than actual speed. This causes a drop in accelerating performance and encourages the driver to repair malfunction.

Device fix mode
  • Fixes electric intake valve timing control motor in the reference position.

  • Fixes exhaust valve timing control solenoid valve in the reference position.

Combustion control mode Stratified charge combustion control at starting No stratified charge combustion at starting (cold start).

DTC Confirmation Procedure

CHECK DTC PRIORITY

If the following DTCs are detected together with P0087, prioritize the service for each DTC in the following order.

Priority DTC Cause
1 P0090, P0091, P0092 High pressure fuel pump, Harness, Fuse, Relay
P0190, P0191, P0192, P0193, P119C, P119D, P119E Fuel pressure sensor, Harness
P020x (x: Cyl No.), P0262, P0265, P0268, P0271, P0274, P0277 Injector, Harness
P025A, P025B, P025C, P025D Low pressure fuel pump
P0461, P0462 Fuel gage, Harness
P062B, P026D ECM, Harness
2 P119A, P119B Fuel pressure sensor
3 P1197 Fuel run out

Is applicable DTC detected?

YES>>

Perform the diagnosis of the applicable. Refer to DTC Index.

NO>>

GO TO 2.

CHECK FUEL LEAKAGE

  1. Ignition switch ON.

  2. Visually check the piping between low pressure fuel pump and fuel injectors for fuel leakage.

  3. Start the engine.

  4. Visually check the piping between low pressure fuel pump and fuel injectors for fuel leakage.

Is inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace error-detected parts.

PRECONDITIONING

If DTC CONFIRMATION PROCEDURE has been previously conducted, always perform the following procedure before conducting the next test.

  1. Ignition switch OFF and wait at least 10 seconds.

  2. Ignition switch ON.

  3. Ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

  • Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.

  • Before performing the following procedure, check that the fuel tank is 1/8 full of fuel.

>>

GO TO 4.

PERFORM DTC CONFIRMATION PROCEDURE-I

With CONSULT

  1. Ignition switch ON.

  2. On CONSULT screen, select “ENGINE”>>“Data Monitor”>>“COOLAN TEMP/S”.

  3. Check the following condition;

    COOLAN TEMP/S −12 – 40 °C

With GST

Follow the procedure “With CONSULT” above.

Is the condition satisfied?

YES>>

GO TO 5.

NO>>

  1. Satisfy the condition.

  2. Retry from step 1.

PERFORM DTC CONFIRMATION PROCEDURE-II

  1. Start the engine and let it idle for 10 seconds.

  2. Check 1st trip DTC.

Is DTC P0087 detected?

YES>>

Proceed to Diagnosis Procedure.

NO>>

GO TO 6.

PERFORM DTC CONFIRMATION PROCEDURE-III

With CONSULT

  1. On CONSULT screen, select “ENGINE”>>“Data Monitor”>>“COOLAN TEMP/S”.

  2. Maintain the following condition for 10 seconds or more at idle.

    COOLAN TEMP/S 70 °C or more
  3. Check 1st trip DTC.

With GST

Follow the procedure “With CONSULT” above.

Is DTC P0087 detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK DTC PRIORITY

If the following DTCs are detected together with P0087, prioritize the service for each DTC in the following order.

Priority DTC Cause
1 P0090, P0091, P0092 High pressure fuel pump, Harness, Fuse, Relay
P0190, P0191, P0192, P0193, P119C, P119D, P119E Fuel pressure sensor, Harness
P020x (x: Cyl No.), P0262, P0265, P0268, P0271, P0274, P0277 Injector, Harness
P025A, P025B, P025C, P025D Low pressure fuel pump
P0461, P0462 Fuel gage, Harness
P062B, P026D ECM, Harness
2 P119A, P119B Fuel pressure sensor
3 P1197 Fuel run out

Is applicable DTC detected?

YES>>

Perform the diagnosis of the applicable. Refer to DTC Index.

NO>>

GO TO 2.

CHECK FUEL LEVEL

Check that the fuel level is enough.

Is there 1/8 or more fuel?

YES>>

GO TO 4.

NO>>

GO TO 3.

REFUEL THE Nissan Pathfinder Vehicle

  1. Refuel to over 1/8 of full.

  2. Start the engine and keep the engine speed at 3,000 rpm for 30 seconds.

  3. Ignition switch OFF and wait at least 10 seconds.

  4. Ignition switch ON.

  5. Ignition switch OFF and wait at least 10 seconds.

  6. Ignition switch ON.

  7. Erase the DTC.

  8. Start the engine and let it idle at least 60 seconds.

  9. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC P0087 detected?

YES>>

GO TO 4.

NO>>

INSPECTION END

AIR BLEED THE FUEL LINE

  1. Start the engine, and let the engine run at idle at least for 10 minutes.

  2. Perform DTC confirmation procedure of DTC P0087.

Is 1st trip DTC detected?

YES>>

GO TO 5.

NO>>

GO TO 18.

CHECK HIGH FUEL PRESSURE (FEED PRESSURE)

  1. Perform fuel pressure release. Refer to Work Procedure.

  2. Ignition switch ON and select “DATA MONITOR” mode of “ENGINE” using CONSULT.

  3. Check the indication of “FUEL PRES SEN”.

    Monitor item Indication
    FUEL PRES SEN Approx. 0.450 Mpa or more

Check high pressure fuel pump. Refer to Component Inspection (High Pressure Fuel Pump).

Is inspection result normal?

YES>>

GO TO 6.

NO>>

GO TO 10.

CHECK HIGH PRESSURE FUEL PUMP

Check high pressure fuel pump. Refer to Component Inspection (High Pressure Fuel Pump).

Is inspection result normal?

YES>>

GO TO 7.

NO>>

Repair or replace the error-detected parts.

CHECK FUEL RAIL PRESSURE SENSOR

Check fuel rail pressure sensor. Refer to Component Inspection (Fuel Rail Pressure Sensor).

Is inspection result normal?

YES>>

GO TO 8.

NO>>

Repair or replace the error-detected parts.

CHECK HIGH PRESSURE FUEL LEAKAGE

  1. Start the engine.

  2. Visually check that the high pressure fuel pump, fuel rail, and fuel piping have no fuel leakage.

Is inspection result normal?

YES>>

GO TO 9.

NO>>

Replace the error-detected parts.

CHECK HIGH PRESSURE FUEL PUMP LIFTER

Check high pressure fuel pump lifter. Refer to Removal and Installation.

Does the lifter top surface have scratches and/or dents?

YES>>

Replace the error-detected parts.

NO>>

GO TO 16.

CHECK LOW FUEL PRESSURE

Check low fuel pressure. Refer to Work Procedure.

Is inspection result normal?

YES>>

GO TO 11.

NO>>

GO TO 16.

CHECK FUEL RAIL PRESSURE SENSOR

Check fuel rail pressure sensor. Refer to Component Inspection (Fuel Rail Pressure Sensor).

Is inspection result normal?

YES>>

GO TO 12.

NO>>

Repair or replace the error-detected parts.

CHECK HIGH PRESSURE FUEL LEAKAGE

  1. Start the engine.

  2. Visually check that the high pressure fuel pump, fuel rail, and fuel piping have no fuel leakage.

Is inspection result normal?

YES>>

GO TO 13.

NO>>

Replace the error-detected parts.

CHECK HIGH PRESSURE FUEL PUMP LIFTER

Check high pressure fuel pump lifter. Refer to Removal and Installation.

Does the lifter top surface have scratches and/or dents?

YES>>

Replace the error-detected parts.

NO>>

GO TO 14.

REPLACE HIGH PRESSURE FUEL PUMP

Replace the high pressure fuel pump. Refer to Removal and Installation.

>>

GO TO 15.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Erase DTC.

  2. Perform DTC confirmation procedure. Refer to DTC Confirmation Procedure.

Is the DTC P0087 detected again?

YES>>

Replace the fuel rail. Refer to Removal and Installation.

NO>>

INSPECTION END

CHECK LOW PRESSURE FUEL PUMP

Check low pressure fuel pump. Refer to Component Function Check.

Is inspection result normal?

YES>>

GO TO 17.

NO>>

Repair or replace the error-detected parts.

DETECT MALFUNCTIONING PART

Check fuel hoses and fuel tubes for clogging.

Is inspection result normal?

YES>>

GO TO 18.

NO>>

Repair or replace the error-detected parts.

CHECK FPCM

Check FPCM. Refer to Component Inspection (Fuel Pump Control Module).

Is inspection result normal?

YES>>

GO TO 19.

NO>>

Repair or replace the error-detected parts.

CHECK LOW PRESSURE FUEL LINE FOR INTERNAL LEAKAGE

  1. Start the engine.

  2. Visually check that the low pressure fuel pump, fuel rail, and fuel piping have no fuel leakage.

Is inspection result normal?

YES>>

INSPECTION END

NO>>

Replace the error-detected parts.

Component Inspection (High Pressure Fuel Pump)

CHECK HIGH PRESSURE FUEL PUMP-I

  1. Ignition switch OFF.

  2. Disconnect high pressure fuel pump harness connector.

  3. Check the resistance between high pressure fuel pump terminals.

    High pressure fuel pump Condition Resistance
    + −
    Terminal
    1 2 Temperature °C (°F) 20 (68) 0.45 – 0.55 Ω

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace high pressure fuel pump. Refer to Removal and Installation.

CHECK HIGH PRESSURE FUEL PUMP-II

With CONSULT

  1. Reconnect high pressure fuel pump harness connector.

  2. Start engine.

  3. On CONSULT screen, select “ENGINE”>>“Data Monitor”.

  4. Check that the “FUEL PRES SEN V” indication.

    Monitor Item Condition Values/Status
    FUEL PRES SEN V Engine speed: Idle 1.120 – 1.310 V
    Engine speed: Revving engine from idle to 4,000 rpm quickly 1.120 – 2.900 V

Without CONSULT

  1. Reconnect high pressure fuel pump harness connector.

  2. Start engine.

  3. Check fuel rail pressure sensor signal voltage.

ECM Condition Voltage
Connector + −
Terminal
F78 47 85 Engine speed: Idle 1.12 – 1.31 V
Engine speed: Revving engine from idle to 4,000 rpm quickly 1.12 – 2.90 V

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace high pressure fuel pump. Refer to Removal and Installation.

P00d2 Ho2s2 Heater Nissan Pathfinder SUV

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P00D2 00

Heated O2 sensor heater B1 sensor 2

(HO2S heater controlcircuit range/performance bank 1 sensor 2)
Diagnosis condition —
Signal (terminal) Heated oxygen sensor 2 heater signal
Threshold Deterioration in heated oxygen sensor 2 heater (bank 1) performance. (Voltage signal transmitted from heated oxygen sensor 2 heater (bank 1) to ECM is higher /lower than voltage in the normal range.)
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors

    [The heated oxygen sensor 2 heater (bank 1) circuit is open or shorted.]

  • Heated oxygen sensor 2 heater (bank 1)

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

PRECONDITIONING

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and warm it up to the normal operating temperature.

  2. Turn ignition switch OFF and wait at least 10 seconds.

  3. Turn ignition switch ON.

  4. Turn ignition switch OFF and wait at least 10 seconds.

  5. Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1 minute under no load.

  6. Let engine idle for 1 minute.

  7. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK HEATED OXYGEN SENSOR 2 (HO2S2) POWER SUPPLY CIRCUIT

  1. Disconnect heated oxygen sensor 2 (HO2S2) harness connector.

  2. Turn ignition switch ON.

  3. Check the voltage between HO2S2 harness connector and ground.

    DTCHO2S2GroundVoltage
    BankConnectorTerminal
    P00D2 1 F71 1 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 2.

DETECT MALFUNCTIONING PART

Check the following.

  • 15A fuse (No. 82)

  • Harness for open or short between heated oxygen sensor 2 and fuse

  • Loose or poor connection for each connector and harness

>>

Repair open circuit, short to ground or short to power in harness or connectors.

CHECK HO2S2 OUTPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between HO2S2 harness connector and ECM harness connector.

    DTCHO2S2ECMContinuity
    BankConnectorTerminalConnectorTerminal
    P00D2 1 F71 2 F78 6 Existed
  4. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair open circuit, short to ground or short to power in harness or connectors.

CHECK HO2S2 HEATER

Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

GO TO 5.

REPLACE HEATED OXYGEN SENSOR 2

Replace malfunctioning heated oxygen sensor 2. Refer to Removal and Installation.

>>

INSPECTION END

CHECK INTERMITTENT INCIDENT

Refer to Intermittent Incident.

>>

INSPECTION END

Component Inspection

HEATED OXYGEN SENSOR 2 HEATER

  1. Check resistance between HO2S2 terminals as follows.

    Terminal No.Resistance
    1 and 2 5.4 – 7.3 Ω at 25 °C
    2 and 3, 4

    ∞Ω

    (Continuity should not exist)
    3 and 4
  2. If NG, replace heated oxygen sensor 2.

P00fe Evap Control System Nissan Pathfinder

DTC Description

This diagnosis detects clogs in the EVAP line between fuel tank and EVAP canister purge volume control solenoid valve.

ECM controls EVAP control system as below. ECM monitors EVAP line pressure change to diagnose if there is no clogging between EVAP canister and fuel tank.

  1. ECM closes EVAP canister vent control valve while the engine is running.

  2. ECM controls EVAP canister purge volume control solenoid valve. (Fuel vapor in EVAP line is absorbed by intake manifold pressure)

  3. ECM monitors EVAP line pressure change using EVAP control system pressure sensor. (When there is clogging in EVAP line, the path to the space of fuel tank is partially blocked. As a result, the pressure in EVAP line drops faster.)

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P00FE 00

EVAP system vapor line

(EVAP system tank vapor line restricted/blocked)
Diagnosis condition —
Signal (terminal) —
Threshold When EVAP canister vent control valve is closed while EVAP canister purge volume control solenoid valve is activated, the pressure of EVAP control system drops extraordinary.
Diagnosis delay time —

POSSIBLE CAUSE

  • Fuel tank vent line (bent, clogs, etc.)

  • EVAP canister

FAIL-SAFE

Not applicable

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Drive the Nissan Pathfinder vehicle under the following conditions for at least 5 minutes in total.

    Engine coolant temperature 70 °C or more
    Nissan Pathfinder Vehicle speed 60 – 100 km/h
  2. Check DTC.

Is 1st trip DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident .

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK EVAP CONTROL SYSTEM FOR CLOGGING

With CONSULT

  1. Turn ignition switch OFF.

  2. Disconnect EVAP purge hose from EVAP canister purge volume control valve.

  3. Disconnect fuel tank vent hose from EVAP canister.

  4. Turn ignition switch ON (engine stopped).

  5. On CONSULT screen, select “ENGINE” >> “Work support” >> “EVAP SYSTEM CLOSE”.

  6. Apply positive pressure (not vacuum) to the hose end using Vacuum/Pressure Hand Pump according to CONSULT screen instructions.

  7. Check that the applied pressure does not increase and that pressure is not held.

Is the inspection result normal?

YES>>

Check fuel tank vent line for clogs, vent and installation condition.

NO>>

Replace EVAP canister. Refer to Removal and Installation.

P0101 Maf Sensor Nissan Pathfinder R53

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0101 00

MAF SEN/CIRCUIT-B1

(Mass or volume air flow “A” circuit range/performance)
Diagnosis condition —
Signal (terminal) Mass air flow sensor signal
Threshold
  • A low frequency from the sensor is sent to ECM under light load driving condition

  • A high frequency from the sensor is sent to ECM under heavy load driving condition

Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors (The mass air flow sensor circuit is open or shorted.)

  • Mass air flow sensor

  • EVAP control system pressure sensor

  • Intake air leaks

  • Intake air temperature sensor

  • Electric throttle control actuator

  • PCV hose air leak

  • Purge hose air leak

FAIL-SAFE

Fail safe mode Nissan Pathfinder Vehicle behavior
Traveling control mode Accelerator angle variation control

ECM controls the accelerator pedal depression speed to make it slower than actual speed. This causes a drop in accelerating performance and encourages the driver to repair malfunction.

Engine output control

ECM reduces the engine output, according to the rise in engine speed. This reduces the Nissan Pathfinder vehicle speed to encourage the driver to repair malfunction.

  • Driving at 70 km/h or more is possible.

Device fix mode
  • Fixes electric intake valve timing control motor in the reference position.

  • Fixes exhaust valve timing control solenoid valve in the reference position.

Combustion control mode Stratified charge combustion control at starting No stratified charge combustion at starting (cold start).
Idle speed control Stops feedback control of idle speed and controls with specified speed.
Recovery speed control at decelerating Stops recovery speed control by the fuel cut at decelerating and controls with specified speed.
Idle neutral control Stops idle neutral control.
Ignition timing correction control Partially controls ignition timing control.
Retardation control Controls ignition timing delay control in the intermediate water temperature range.

DTC Confirmation Procedure

CHECK DTC PRIORITY

If DTC P0101 is displayed with other DTC, first perform the confirmation procedure (trouble diagnosis) for other DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2.

PRECONDITIONING

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

If engine will not start or stops soon, wait at least 10 seconds with engine stopped (Ignition switch ON) instead of running engine at idle speed.

>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and warm it up to normal operating temperature.

  2. Drive the Nissan Pathfinder vehicle for at least 5 seconds under the following conditions:

    Selector lever Suitable position
    Nissan Pathfinder Vehicle speed 40 km/h or more
  3. Check 1st trip DTC.

Is DTC P0101 detected?

YES>>

Proceed to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P0101 is displayed with other DTC, first perform the confirmation procedure (trouble diagnosis) for other DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2.

CHECK HARNESS CONNECTOR

  1. Disconnect mass air flow sensor harness connector and ECM harness connector.

  2. Connect mass air flow sensor harness connector and ECM harness connector.

  3. Perform DTC confirmation procedure. Refer to DTC Confirmation Procedure.

Is DTC detected?

YES>>

GO TO 3.

NO>>

INSPECTION END

CHECK INTAKE SYSTEM

Check the following items to see the installation condition and the connection condition of the joint.

  • Air duct

  • Vacuum hoses

  • Intake air passage between air duct and intake manifold

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Reconnect or replace error-detected parts.

CHECK MASS AIR FLOW SENSOR POWER SUPPLY

  1. Disconnect mass air flow sensor harness connector.

  2. Turn ignition switch ON.

  3. Check the voltage between mass air flow sensor harness connector and ground.

    + –

    Voltage

    (Approx.)
    Mass air flow sensor
    Connector Terminal
    E64 1 Ground 5 V

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

GO TO 5.

CHECK MASS AIR FLOW SENSOR POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between mass air flow sensor harness connector and ECM harness connector.

    Mass air flow sensor ECM Continuity
    Connector Terminal Connector Terminal
    E64 1 F78 41 Existed
  4. Also check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

Perform the trouble diagnosis for ECM power supply circuit. Refer to Diagnosis Procedure.

NO>>

Repair or replace error-detected parts.

CHECK MASS AIR FLOW SENSOR GROUND CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between mass air flow sensor harness connector and ECM harness connector.

    Mass air flow sensor ECM Continuity
    Connector Terminal Connector Terminal
    E64 3 F78 30 Existed
  4. Also check harness for short to power.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair or replace error-detected parts.

CHECK ECM GROUND CIRCUIT

  1. Check the continuity between ECM harness connector and ground.

    ECM — Continuity
    Connector Terminal
    F78 3 Ground Existed
    F79 87
    E32 199
    201
    204
  2. Also check harness for short to power.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair or replace error-detected parts.

CHECK MASS AIR FLOW SENSOR INPUT SIGNAL CIRCUIT

  1. Check the continuity between mass air flow sensor harness connector and ECM harness connector.

    Mass air flow sensor ECM Continuity
    Connector Terminal Connector Terminal
    E64 2 F78 33 Existed
  2. Also check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Repair or replace error-detected parts.

CHECK INTAKE AIR TEMPERATURE SENSOR

Check intake air temperature sensor. Refer to Component Inspection (Intake Air Temperature Sensor).

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Replace mass air flow sensor (with intake air temperature sensor). Refer to Exploded View.

CHECK PCV VALVE

Check the PCV valve. Refer to Inspection.

Is the inspection result normal?

YES>>

GO TO 11.

NO>>

Replace PCV valve.

PERFORM IDLE AIR VOLUME LEARNING

Perform the idle air volume learning. Refer to Work Procedure.

>>

GO TO 12.

CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR

Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 13.

NO>>

Replace EVAP control system pressure sensor. Refer to Removal and Installation.

PERFORM EVAP LEAK CHECK

Perform EVAP leak check. Refer to Inspection.

>>

GO TO 14.

CHECK MASS AIR FLOW SENSOR

Check mass air flow sensor. Refer to Component Inspection (Mass Air Flow Sensor).

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace mass air flow sensor. Refer to Exploded View.

P0107 Barometric Pressure Sensor Nissan Pathfinder Fifth generation

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0107 00

ABSL PRES SEN/CIRC

(Barometric pressure sensor circuit low input)
Diagnosis condition —
Signal (terminal) —
Threshold An excessively low voltage from the barometric pressure sensor (built-into ECM) is sent to ECM.
Diagnosis delay time —

POSSIBLE CAUSE

Barometric pressure sensor (built-into ECM)

FAIL-SAFE

Fail safe modeNissan Pathfinder Vehicle behavior
Traveling control mode Accelerator angle variation control

ECM controls the accelerator pedal depression speed to make it slower than actual speed. This causes a drop in accelerating performance and encourages the driver to repair malfunction.

Engine output control

ECM reduces the engine output, according to the rise in engine speed. This reduces the Nissan Pathfinder vehicle speed to encourage the driver to repair malfunction.

  • Driving at 70 km/h or more is possible.

Device fix mode
  • Fixes electric intake valve timing control motor in the reference position.

  • Fixes exhaust valve timing control solenoid valve in the reference position.

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and let it idle for 5 seconds.

  2. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

DTC CONFIRMATION

  1. Turn ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure. Refer to DTC Description.

  4. Check the DTC.

Is the DTC displayed again?

YES>>

Replace ECM. Refer to Removal and Installation.

NO>>

INSPECTION END

P0111 Iat Sensor Nissan Pathfinder 5th Gen

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0111 00

IAT SENSOR 1 B1

(Intake air temperature sensor 1 circuit range/performance bank 1)
Diagnosis condition Engine cold start
Signal (terminal) Intake air temperature sensor signal
Threshold The comparison result of signals transmitted to ECM from each temperature sensor (IAT sensor, ECT sensor, FTT sensor, and EOT sensor) shows that the voltage signal of the IAT sensor is higher/lower than that of other temperature sensors.
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors (High or low resistance in the IAT sensor circuit)

  • Mass air flow sensor (IAT sensor)

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

INSPECTION START

Is it necessary to erase permanent DTC?

YES>>

GO TO 3.

NO>>

GO TO 2.

PERFORM COMPONENT FUNCTION CHECK

  1. Turn ignition switch OFF.

  2. Disconnect mass air flow sensor harness connector.

  3. Check resistance between mass air flow sensor terminals as follows.

    Mass air flow sensorConditionResistance
    Terminal
    3 4 Temperature [°C (°F)] 25 (77) 1.80 – 2.20 kΩ

Is the inspection result normal?

YES-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

YES-2>>

Confirmation after repair: INSPECTION END

NO>>

Proceed to Diagnosis Procedure.

PRECONDITIONING

If DTC CONFIRMATION PROCEDURE has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

  • Before performing the following procedure, do not add fuel.

  • Before performing the following procedure, check that fuel level is between 1/4 and 4/4.

  • Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.

>>

GO TO 4.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Move the Nissan Pathfinder vehicle to a cool place.

  2. Turn ignition switch OFF and leave the Nissan Pathfinder vehicle for 12 hours.

  3. Start engine and let it idle for 5 minutes or more.

  4. Check 1st trip DTC.

Is DTC P0111 detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK INTAKE AIR TEMPERATURE SENSOR

Check intake air temperature sensor. Refer to Component Inspection.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace mass air flow sensor (with intake air temperature sensor). Refer to Exploded View.

Component Inspection

CHECK INTAKE AIR TEMPERATURE SENSOR

With CONSULT

  1. Turn ignition switch OFF.

  2. Disconnect mass air flow (MAF) sensor (intake air temperature sensor is built-into) harness connector and reconnect it.

  3. Turn ignition switch ON.

  4. On CONSULT screen, select “ENGINE”>>“Data Monitor”>>“INT/A TEMP SEN”.

  5. Check that the indicated value of “INT/A TEMP SEN” is almost the same as intake air temperature.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace mass air flow sensor (with intake air temperature sensor). Refer to Exploded View.