Basic Inspection - Camera Aiming Adjustment ++
Work Procedure
Always adjust the camera aiming after removing and installing or replacing the front camera unit.
Always adjust the camera aiming after removing and installing or replacing the windshield glass.
Preparation
PERFORM SELF-DIAGNOSIS
Perform self-diagnosis of front camera unit.
Is any DTC detected?
YES>>
Perform diagnosis on the detected DTC and repair or replace the applicable item. Refer to DTC Index.
NO>>
GO TO 2.
PREPARATION BEFORE CAMERA AIMING ADJUSTMENT
Perform pre-inspection for diagnosis.
Adjust the tire pressure to the specified pressure value.
Maintain no-load in Nissan Pathfinder vehicle.
Check if coolant and engine oil are filled up to correct level and fuel tank is full.
Shift the selector lever to “P” position and release the parking brake.
Clean the windshield.
Completely clear off the instrument panel.
>>
GO TO 3.
PREPARATION OF J-52266-2 ALIGNMENT TARGET
Prepare the alignment target according to the following procedure and the figure.
Attach the J-52266-2 alignment target to a movable board.


White wall 
String 
Cone 
Center between two targets Side of a target (Ts) : 120 mm (4.72 in) Height of a target lower end (Htl) : 1,180 mm (46.46 in) Height of a target center (Ht) : 1,300 mm (51.18 in) Height of a target upper end (Htu) : 1,420 mm (55.91 in) Width between a right target center from a left target center (Dbt) : 720 mm (28.35 in) W1 : 180 mm (7.09 in) W2 : 180 mm (7.09 in)
>>
Proceed to Target Setting.
Target Setting
TARGET SETTING

| A – E (C – F) | : 3,000 mm (118.11 in) |
Mark points “A”, “B”, “C” and “D”at the center of the lateral surface of each wheels.

Draw line “LH” passing through points “A” and “B” on the left side of Nissan Pathfinder vehicle.
Mark point “E” on the line “LH” at the positions 3,000 mm (118.11 in) from point “A”.
Draw line “RH” passing through points “C” and “D” on the right side of Nissan Pathfinder vehicle in the same way as step 2.
Mark point “F” on the line “RH” at the positions 3,000 mm (118.11 in) from point “C”.
Draw line “FW” passing through the points “E” and “F” on the front side of Nissan Pathfinder vehicle.
Mark point “X” at the center of point “E” and “F” on the line “FW”.
Center the J-52266-2 alignment target at point "X" facing the Nissan Pathfinder vehicle.

Dt : 3,000 mm (118.11 in)
>>
Proceed to Camera Aiming Adjustment.
Camera Aiming Adjustment
CHECK VEHICLE HEIGHT
Measure the wheelarch height.

| Hfl: Front left wheelarch height [mm] | |
| Hfr: Front right wheelarch height [mm] |
>>
GO TO 2.
CAMERA AIMING ADJUSTMENT
With CONSULT
Select “Work Support” on “LANE CAMERA” with CONSULT.
Select “AUTO AIM”.
Confirm the following items;
The target should be accurately placed.
The Nissan Pathfinder vehicle should be stopped.
Select “Start” to perform camera aiming.
Input the following parameters, and then select “Start”.
Hfl : Measured value Hfr : Measured value Nissan Pathfinder Vehicle Reference Value : 837 VP : 0 Dt : 3,000 mm Dbt : 720 mm Htu : 1,420 mm Htl : 1,180 mm Ts : 120 mm Confirm the displayed item.
“Normally Completed”: Select “Completion”.
“SUSPENSION”, “Abnormally completed”: Perform the following services.
Displayed item Possible cause Service procedure SUSPENSION — Temporary malfunction in internal processing of the front camera unit. Go back to step 1. 00H Routine not activated Front camera unit malfunction. Position the target appropriately again.
Then perform the aiming again.10H Writing error Temporary malfunction in internal processing of the front camera unit.
Front camera unit malfunction.
Abnormally completed 2 Front camera unit cannot detect the target
A target is not-yet-placed.
The position of the targets is not correct.
The position of the front camera unit is not correct.
Inappropriate work environment.
Inappropriate Nissan Pathfinder vehicle condition.
Input value is not correct against actual setting position.
Position the target appropriately again.
Then perform the aiming again.3 Roll angle is outside the threshold
The position of the targets is not correct.
The position of the front camera unit is not correct.
Inappropriate work environment.
Inappropriate Nissan Pathfinder vehicle condition.
Input value is not correct against actual setting position.
4 Yaw/pitch angle is outside the threshold.
The position of the targets is not correct.
The position of the front camera unit is not correct.
Inappropriate work environment.
Inappropriate Nissan Pathfinder vehicle condition.
Input value is not correct against actual setting position.
5 Input value of aiming is invalid.
Input value is not correct against actual setting position.
Correct input value of aiming and perform camera aiming again. 6 The size of target is different. (A numerical value input to CONSULT differs from detected size)
The position of the targets is not correct.
The position of the front camera unit is not correct.
Inappropriate work environment.
Inappropriate Nissan Pathfinder vehicle condition.
Input value is not correct against actual setting position.
Position the target appropriately again.
Then perform the aiming again.7 The size of target is different. (A numerical value input to CONSULT differs from detected size)
The position of the targets is not correct.
The position of the front camera unit is not correct.
Inappropriate work environment.
Inappropriate Nissan Pathfinder vehicle condition.
Input value is not correct against actual setting position.
8 Yaw/pitch angle is outside the threshold.
The position of the targets is not correct.
The position of the front camera unit is not correct.
Inappropriate work environment.
Inappropriate Nissan Pathfinder vehicle condition.
Input value is not correct against actual setting position.
9 Yaw/pitch angle is outside the threshold.
The position of the targets is not correct.
The position of the front camera unit is not correct.
Inappropriate work environment.
Inappropriate Nissan Pathfinder vehicle condition.
Input value is not correct against actual setting position.
10 Detect several targets.
The position of the targets is not correct.
The position of the front camera unit is not correct.
Inappropriate work environment.
Inappropriate Nissan Pathfinder vehicle condition.
Input value is not correct against actual setting position.
11 Internal process malfunction Then turn the ignition switch OFF→ON. Accurately set target and perform camera aiming again.
If ABNORMALLY COMPLETED again after aiming, replace front camera unit.
12 Internal process time out Then turn the ignition switch OFF→ON. Accurately set target and perform camera aiming again.
If ABNORMALLY COMPLETED again after aiming, replace front camera unit.
Confirm that “Normally completed” is displayed and then select “End” to close the adjustment procedure.
>>
GO TO 3.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis of “LANE CAMERA” with CONSULT.
Is any DTC detected?
YES>>
Perform diagnosis on the detected DTC and repair or replace the applicable item. Refer to DTC Index.
NO>>
GO TO 4.
ACTION TEST
Perform the following system operation by action test.
LDW: Refer to Work Procedure.
I-LI: Refer to Work Procedure.
I-BSI: Refer to Work Procedure.
TSR: Refer to Work Procedure.
ProPILOT Assist: Refer to Work Procedure(7 inch information display) Work Procedure(FULL TFT METER).
>>
WORK END