Dtc/circuit Diagnosis - Lane Camera (front Camera Unit) ++

In this manual: Dtc/circuit Diagnosis - Lane Camera (front Camera Unit) ++
General Information — 8Engine :: Engine Mechanical — 19Engine Lubrication System - Precautions. Preparation — 1Engine Lubrication System - Lubrication System (System Description). Engine Oil Pressure (Basic Inspection). Service Data and Specifications (SDS) — 1Engine Cooling System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Engine Cooling System - Engine Coolant — 1Engine Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Engine Control System - Ecu Diagnosis Information — 1Ecu Diagnosis Information - Ecm ++ — 1Engine Control System - Basic Inspection — 1Basic Inspection - Diagnosis and Repair Workflow ++ — 1Basic Inspection - Basic Inspection ++ — 1Basic Inspection - Additional Service When Replacing Ecm ++ — 1Basic Inspection - Fuel Pressure Check ++ — 1Basic Inspection - How to Set Srt Code ++ — 1Basic Inspection - How to Erase Permanent Dtc ++ — 1Engine Control System - Dtc/circuit Diagnosis — 1Engine Control System - Symptom Diagnosis — 1Engine Control System - Periodic Maintenance — 1Engine Control System - Removal and Installation — 1Fuel System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Fuel System - Fuel System (Periodic Maintenance). Fuel Level Sensor Unit (Disassembly and Assembly) — 1Exhaust System - Precautions. Preparation — 1Exhaust System - Exhaust System (Periodic Maintenance). Exhaust System (Removal and Installation) — 1Starting System - Precautions. Preparation. Starter Motor (Service Data and Specifications (sds)) — 1Starting System - Diagnosis and Repair Work Flow — 1Starting System - Starting System (Symptom Diagnosis). Starter Motor (Removal and Installation) — 1Accelerator Control System - Precautions. Service Data and Specifications (SDS) — 1Accelerator Control System - Accelerator Pedal Assembly — 1Transmission & Driveline :: Transaxle & Transmission — 21Driveline - System Description — 1Transfer: Ty92b - Ecu Diagnosis Information. Awd Control Unit ++ — 1Driveline - Basic Inspection — 1Driveline - Dtc/circuit Diagnosis — 1Driveline - Symptom Diagnosis — 1Driveline - Removal and Installation — 1Transfer: Ty92b - Unit Removal and Installation. Transfer Assembly ++ — 1Driveline - Unit Disassembly and Assembly — 1Driveline - Basic Inspection — 1Driveline - Removal and Installation — 1Driveline - Unit Disassembly and Assembly — 1Front Axle - Precautions. Preparation — 1Front Axle - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Front Axle - Front Drive Shaft Boot — 1Front Axle - Front Drive Shaft — 1Rear Axle - Precautions. Preparation. Service Data and Specifications (SDS) — 1Rear Axle - Noise, Vibration and Harshness (nvh) Troubleshooting — 1Rear Axle - Rear Drive Shaft — 1Suspension :: Front Suspension — 7Rear Suspension - Precautions. Preparation — 1Rear Suspension - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Rear Suspension - Rear Suspension Assembly — 1Road Wheels & Tires - Precautions — 1Road Wheels & Tires - Preparation. Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Road Wheels & Tires - System — 1Brakes :: Brake System — 9Parking Brake System - Precautions. Preparation — 1Parking Brake System - System — 1Vdc/tcs/abs - Precautions ++ — 1Brake Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Dtc/circuit Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Steering :: Steering System — 9Steering Control System - Precautions — 1Steering Control System - System — 1Steering Control System - Eps Control Unit (Ecu Diagnosis Information. Removal and Installation) — 1Restraints :: Seat Belt — 7Srs Air Bag - Precautions. Preparation — 1Srs Air Bag - Collision Diagnosis — 1Srs Air Bag - Occupant Classification System — 1Srs Air Bag Control System - Precautions — 1Srs Air Bag Control System - System — 1Srs Air Bag Control System - Diagnosis Sensor Unit — 1Srs Air Bag Control System - Inspection and Adjustment — 1Ventilation, Heater & Air Conditioner :: Ventilation System — 6Heater & Air Conditioning System - Precautions — 1Heater & Air Conditioning System - Preparation — 1Heater & Air Conditioning System - Component Parts — 1Heater & Air Conditioning System - Diagnosis and Repair Work Flow — 1Heater & Air Conditioning System - Compressor — 1Heater & Air Conditioning System - Cooler Pipe and Hose — 1Heater & Air Conditioning System - Condenser. Condenser — 1Heater & Air Conditioning System - Heating and Cooling Unit Assembly — 1Heater & Air Conditioning System - Service Data and Specifications (SDS) — 1Heater & Air Conditioning Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1Heater & Air Conditioning Control System - Ecu Diagnosis Information — 1Heater & Air Conditioning Control System - Basic Inspection — 1Heater & Air Conditioning Control System - Dtc/circuit Diagnosis — 1Heater & Air Conditioning Control System - Symptom Diagnosis — 1Heater & Air Conditioning Control System - Removal and Installation — 1Body Interior :: Interior — 8Instrument Panel - Precautions. Preparation. Clip List — 1Instrument Panel - Squeak and Rattle Trouble Diagnoses — 1Instrument Panel - Cluster Lid C — 1Seat - Precautions — 1Seat - Preparation. Clip List — 1Seat - Component Parts — 1Seat - System — 1Seat - Diagnosis and Repair Work Flow — 1Seat - Front Seat — 1Seat - Second Row Seats — 1Seat - Third Row Seats — 1Seat - Front Seat — 1Seat - Second Row Seat — 1Seat - Third Row Seat — 1Automatic Drive Positioner - Precautions. Preparation — 1Automatic Drive Positioner - System — 1Automatic Drive Positioner - Diagnosis and Repair Work Flow — 1Automatic Drive Positioner - Inspection and Adjustment — 1Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock — 38Security Control System - Precautions — 1Security Control System - System — 1Security Control System - Ecm, Bcm, Intelligent Key Unit, Ipdm E/r — 1Security Control System - Vehicle Security System Cannot Be Set — 1Glass & Window System - Precautions. Preparation — 1Glass & Window System - Squeak and Rattle Trouble Diagnoses — 1Power Window Control System - Precautions. Preparation — 1Power Window Control System - Power Supply and Ground Circuit — 1Power Window Control System - Power Window Motor Circuit — 1Power Window Control System - Front Power Window Rh Alone Does Not Operate — 1Power Window Control System - Rear Lh Side Power Window Alone Does Not Operate — 1Power Window Control System - Rear Rh Side Power Window Alone Does Not Operate — 1Roof - Precautions. Preparation — 1Roof - Power Supply and Ground Circuit — 1Roof - Moonroof Switch Assembly — 1Roof - Lin Communication Circuit — 1Roof - Auto Operation Does Not Operate — 1Roof - Anti-Pinch Function Does Not Operate — 1Exterior - Precautions. Preparation. Clip List (Preparation) — 1Exterior - Squeak and Rattle Trouble Diagnoses — 1Exterior - Fender Protector — 1Exterior - Over Fender — 1Exterior - Under Cover — 1Exterior - Roof Side Rail — 1Body Repair - Service Information — 1Service Information - Sheet Metal Work ++ — 1Service Information - Body Welding and Precautions ++ — 1Service Information - Safety and Health ++ — 1Service Information - Repairing Procedures and Precautions ++ — 1Body Repair - Precaution — 1Body Repair - Preparation — 1Body Repair - Removal and Installation — 1Driver Controls :: Mirrors — 8Exterior Lighting System - System Description — 1System Description - Component Parts ++ — 1Exterior Lighting System - Basic Inspection — 1Exterior Lighting System - Dtc/circuit Diagnosis — 1Exterior Lighting System - Symptom Diagnosis — 1Exterior Lighting System - Periodic Maintenance — 1Exterior Lighting System - Removal and Installation — 1Interior Lighting System - Precautions. Preparation — 1Interior Lighting System - Component Parts. Interior Lighting System — 1Interior Lighting System - System — 1Interior Lighting System - Diagnosis and Repair Work Flow — 1Interior Lighting System - Interior Lighting System Symptoms (Symptom Diagnosis). Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Interior Lighting System - Foot Lamp — 1Wiper & Washer - Precautions — 1Wiper & Washer - Preparation. Bcm, Ipdm E/r (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Wiper & Washer - System — 1Wiper & Washer - Diagnosis and Repair Work Flow — 1Defogger - Precautions. Bcm, A/c Auto Amp. (Ecu Diagnosis Information) — 1Defogger - Diagnosis and Repair Work Flow — 1Horn - Precautions — 1Electrical & Power Control :: Power Outlet — 13Body Control System - Precautions. Preparation — 1Body Control System - Component Parts — 1Body Control System - System — 1Body Control System - Diagnosis System (bcm) — 1Body Control System - Bcm — 1Lan System - System Description — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - Removal and Installation — 1Charging System - Precautions. Preparation. Ecm, Ipdm E/r (Ecu Diagnosis Information) — 1Charging System - Diagnosis and Repair Work Flow — 1Charging System - Charging System (Symptom Diagnosis). Generator (Removal and Installation). Service Data and Specifications (SDS) — 1Power Supply, Ground & Circuit Elements - Precautions. Preparation. Service Data and Specifications (SDS) — 1Driver Information & Multimedia :: Meter, Warning Lamp & Indicator — 25Warning Chime System - Application Notice (How to Use This Manual). Precautions — 1Warning Chime System - System — 1Warning Chime System - Diagnosis System (combination Meter) — 1Warning Chime System - Bcm, Combination Meter (Ecu Diagnosis Information). Diagnosis and Repair Work Flow (Basic Inspection) — 1Sonar System - Precautions. Preparation — 1Sonar System - Sonar Control Unit — 1Dtc/circuit Diagnosis - B2720 Corner Sensor [rl] ++ — 1Audio, Visual & Navigation System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Multi Av (av Control Unit) ++ — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Symptom Diagnosis - Multi Av System ++ — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Cruise Control & Driver Assistance :: Cruise Control System — 17Driver Assistance System - System Description — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Driver Assistance System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1System Description - Handling Precaution ++ — 1Driver Assistance System - Ecu Diagnosis Information — 1Driver Assistance System - Basic Inspection — 1Basic Inspection - Distance Sensor Alignment ++ — 1Basic Inspection - Camera Aiming Adjustment ++ — 1Basic Inspection - Action Test ++ — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Laser/radar (distance Sensor) ++ — 1Dtc/circuit Diagnosis - Lane Camera (front Camera Unit) ++ — 1Driver Assistance System - Symptom Diagnosis — 1Driver Assistance System - Removal and Installation — 1Driver Assistance System - System Description — 1System Description - System ++ — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Drive Mode System - Precautions — 1Drive Mode System - Component Parts. Drive Mode System — 1Drive Mode System - System — 1Drive Mode System - Diagnosis and Repair Work Flow — 1Drive Mode System - Drive Mode Select Switch Circuit — 1Maintenance - Precautions. Preparation — 1Maintenance - General Maintenance — 1Maintenance - Periodic Maintenance — 1Maintenance - Recommended Fluids and Lubricants — 1Maintenance - Engine Maintenance — 1Maintenance - Chassis and Body Maintenance — 1Engine Lubrication System - Periodic Maintenance — 1Engine Lubrication System - Removal and Installation — 1Engine Cooling System - System Description — 1Engine Cooling System - Removal and Installation — 1Engine Control System - Vq35dd — 1Fuel System - Removal and Installation — 1Starting System - System Description — 1Starting System - Dtc/circuit Diagnosis — 1Driveline - Transfer: Ty92b — 1Driveline - Rear Propeller Shaft: 3fcj-Cvj — 1Driveline - Rear Final Drive: R145 — 1Front Axle - Periodic Maintenance — 1Front Axle - Removal and Installation — 1Rear Axle - Periodic Maintenance — 1Rear Axle - Removal and Installation — 1Rear Suspension - Removal and Installation — 1Road Wheels & Tires - System Description — 1Road Wheels & Tires - Basic Inspection — 1Road Wheels & Tires - Dtc/circuit Diagnosis — 1Road Wheels & Tires - Symptom Diagnosis — 1Road Wheels & Tires - Periodic Maintenance — 1Road Wheels & Tires - Removal and Installation — 1Parking Brake System - System Description — 1Parking Brake System - Basic Inspection — 1Parking Brake System - Dtc/circuit Diagnosis — 1Parking Brake System - Symptom Diagnosis — 1Parking Brake System - Removal and Installation — 1Brake Control System - Vdc/tcs/abs — 1Brake Control System - Automatic Brake Hold — 1Brake Control System - Automatic Emergency Braking — 1Brake Control System - Rear Automatic Braking — 1Steering Control System - System Description — 1Steering Control System - Basic Inspection — 1Steering Control System - Dtc/circuit Diagnosis — 1Steering Control System - Symptom Diagnosis — 1Srs Air Bag - Removal and Installation — 1Srs Air Bag Control System - System Description — 1Srs Air Bag Control System - Basic Inspection — 1Srs Air Bag Control System - Symptom Diagnosis — 1Heater & Air Conditioning System - Symptom Diagnosis — 1Heater & Air Conditioning System - Periodic Maintenance — 1Heater & Air Conditioning Control System - Automatic Air Conditioning — 1Instrument Panel - Removal and Installation — 1Instrument Panel - Unit Disassembly and Assembly — 1Seat - Ecu Diagnosis Information — 1Seat - Dtc/circuit Diagnosis — 1Seat - Symptom Diagnosis — 1Automatic Drive Positioner - System Description — 1Automatic Drive Positioner - Ecu Diagnosis Information — 1Automatic Drive Positioner - Dtc/circuit Diagnosis — 1Automatic Drive Positioner - Symptom Diagnosis — 1Automatic Drive Positioner - Removal and Installation — 1Security Control System - System Description — 1Security Control System - Basic Inspection — 1Security Control System - Dtc/circuit Diagnosis — 1Security Control System - Symptom Diagnosis — 1Security Control System - Removal and Installation — 1Glass & Window System - Removal and Installation — 1Power Window Control System - System Description — 1Power Window Control System - Ecu Diagnosis Information — 1Power Window Control System - Basic Inspection — 1Power Window Control System - Dtc/circuit Diagnosis — 1Power Window Control System - Symptom Diagnosis — 1Power Window Control System - Removal and Installation — 1Roof - System Description — 1Roof - Ecu Diagnosis Information — 1Roof - Basic Inspection — 1Roof - Dtc/circuit Diagnosis — 1Roof - Symptom Diagnosis — 1Roof - Removal and Installation — 1Exterior - System Description — 1Exterior - Removal and Installation — 1Body Repair - Repair Information — 1Exterior Lighting System - Led Headlamp — 1Interior Lighting System - Dtc/circuit Diagnosis — 1Interior Lighting System - Removal and Installation — 1Wiper & Washer - System Description — 1Wiper & Washer - Dtc/circuit Diagnosis — 1Wiper & Washer - Symptom Diagnosis — 1Wiper & Washer - Removal and Installation — 1Defogger - System Description — 1Defogger - Dtc/circuit Diagnosis — 1Defogger - Symptom Diagnosis — 1Defogger - Removal and Installation — 1Horn - Removal and Installation — 1Body Control System - Basic Inspection — 1Body Control System - Dtc/circuit Diagnosis — 1Body Control System - Symptom Diagnosis — 1Body Control System - Removal and Installation — 1Lan System - Can Fundamental — 1Lan System - Can — 1Lan System - Can Gateway — 1Power Control System - Ipdm E/r — 1Power Control System - Power Distribution System — 1Charging System - System Description — 1Charging System - Dtc/circuit Diagnosis — 1Power Supply, Ground & Circuit Elements - System Description — 1Power Supply, Ground & Circuit Elements - Basic Inspection — 1Power Supply, Ground & Circuit Elements - Removal and Installation — 1Warning Chime System - System Description — 1Warning Chime System - Dtc/circuit Diagnosis — 1Warning Chime System - Symptom Diagnosis — 1Sonar System - System Description — 1Sonar System - Basic Inspection — 1Sonar System - Dtc/circuit Diagnosis — 1Sonar System - Symptom Diagnosis — 1Sonar System - Removal and Installation — 1Audio, Visual & Navigation System - Nissanconnect — 1Audio, Visual & Navigation System - Intelligent Around View Monitor System — 1Audio, Visual & Navigation System - Rear View Monitor System — 1Audio, Visual & Navigation System - Telematics System — 1Driver Assistance System - Adas Control Unit 2 — 1Driver Assistance System - Driver Assistance System — 1Driver Assistance System - Chassis Control — 1Drive Mode System - Removal and Installation — 1Dtc/circuit Diagnosis (C053c Wheel Speed Sensor ... U2141 Can Comm Circuit) — 1Dtc/circuit Diagnosis (P0011 Intake Valve Timing Control ... P0111 Iat Sensor) — 1Dtc/circuit Diagnosis (P0116 Engine Coolant Temperature Sensor ... P025b Fuel Pump Module a) — 1Dtc/circuit Diagnosis (P026b Injection Timing ... P0420 Three Way Catalyst Function) — 1Dtc/circuit Diagnosis (P0441 Evap Control System ... P0524 Engine Oil Pressure) — 1Dtc/circuit Diagnosis (P0532 A/c Refrigerant Pressure Sensor ... P064d Ecm) — 1Dtc/circuit Diagnosis (P06da Engine Oil Pressure Control Solenoid Valve ... P1217 Engine Over Temperature) — 1Dtc/circuit Diagnosis (P1220 Fuel Pump Control Module (fpcm) ... P1574 Ascd Vehicle Speed Sensor) — 1Dtc/circuit Diagnosis (P1575 Brake Switch ... P2101 Electric Throttle Control Function) — 1Dtc/circuit Diagnosis (P2118 Throttle Control Motor ... P34ac Electric Intake Valve Timing Control Actuator) — 1Dtc/circuit Diagnosis (Active Grille Shutter ... High Pressure Fuel Pump) — 1Dtc/circuit Diagnosis (Ignition Signal ... Variable Induction Air System) — 14012 C1040 Emergency Brake — 14013 C106a Wheel Sensor — 14014 C1078-55 Not Configuration — 14015 C10b4-98 Overheat — 14016 B1001 Lap Pre-Tensioner Lh — 14017 B0001 Driver Air Bag Module — 14018 B100e Knee Air Bag Module Rh — 14019 B142x Collision Detection — 1Dtc/circuit Diagnosis (B20c7-11 A/c Clutch ... B24a6-11 in-Vehicle Sensor) — 1Dtc/circuit Diagnosis (B24a6-15 in-Vehicle Sensor ... U2140-87 Can Comm Err (ecm)) — 1Dtc/circuit Diagnosis (C1f00-1c Control Unit ... C1f04-61 Brake Sw/stop Lamp Sw) — 1Dtc/circuit Diagnosis (C1f05-49 Front Camera Unit ... C1f70-87 Ethernet Circuit) — 1
312steps
~1872min
4/5difficulty
Done 0 of 312

C2500-49 Front Camera Unit

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2500-49

Camera unit malf

(Camera unit malfunction)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold
  • Configuration of the front camera unit is not completed.

  • If front camera unit is malfunctioning

Diagnosis delay time 1 seconds or more

POSSIBLE CAUSE

  • Configuration of the front camera unit is not completed.

  • Front camera unit

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2500-49” is detected as the current malfunction in “Self Diagnostic Result” of “LANE CAMERA”.

Is “C2500-49” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK SELF-DIAGNOSIS RESULTS

Check if any DTC other than “C2500-49” is detected in “Self Diagnostic Result” of “LANE CAMERA”.

Is any DTC detected?

YES>>

Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to DTC Index.

NO>>

Replace the front camera unit. Refer to Removal and Installation.

C2501-4b Front Camera Unit

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2501-4B

Front camera unit

(Front camera unit)
Diagnosis condition When ignition switch is ON.
Signal (terminal) —
Threshold Temperature around front camera unit is excessively high
Diagnosis delay time 2 second or less

POSSIBLE CAUSE

Interior room temperature is excessively high

FAIL-SAFE

The following systems are canceled.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn the ignition switch OFF.

  2. Wait for 10 minutes or more.

  3. Start the engine.

  4. Turn the AEB system ON.

  5. Perform “All DTC Reading” with CONSULT.

  6. Check if the “C2501-4B” is detected as the current malfunction in “Self Diagnostic Result” of “LANE CAMERA”.

Is “C2501-4B” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1 >>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2 >>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK FRONT CAMERA UNIT SELF-DIAGNOSIS RESULTS

  1. Erase all self-diagnosis results with CONSULT.

  2. Perform “All DTC Reading”.

  3. Check if the “C2501-4B” is detected in “Self Diagnostic Result” of “LANE CAMERA”

Is “C2501-4B” detected?

YES>>

Replace the front camera unit. Refer to Removal and Installation.

NO>>

INSPECTION END

C2502-55 Configuration

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2502-55

Configuration data error

(Configuration data error)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Configuration of the front camera unit is incomplete
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Configuration of the front camera unit is not completed

  • Front camera unit

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2502-55” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2502-55” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM CONFIGURATION OF FRONT CAMERA UNIT

  1. Perform configuration of the front camera unit. Refer to Work Procedure.

  2. Erases self-diagnosis results.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC “C2502-55” detected?

YES>>

Replace the front camera unit. Refer to Removal and Installation.

NO>>

INSPECTION END

C2502-92 Configuration

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2502-92

Configuration data error

(Configuration data error)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Configuration of the front camera unit is incomplete
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Configuration of the front camera unit is not completed

  • Front camera unit

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2502-92” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2502-92” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM CONFIGURATION OF FRONT CAMERA UNIT

  1. Perform configuration of the front camera unit. Refer to Work Procedure.

  2. Erases self-diagnosis results.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC “C2502-92” detected?

YES>>

Replace the front camera unit. Refer to Removal and Installation.

NO>>

INSPECTION END

C2503-54 Cam Aiming Incmp

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2503-54

Camera aiming incmp

(Camera aiming incomplete)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Camera aiming is not completed
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Lane camera aiming is not completed

  • Lane camera aiming adjustment has been interrupted

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2503-54” is detected as the current malfunction in “Self Diagnostic Result” of “LANE CAMERA”.

Is “C2503-54” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CAMERA AIMING ADJUSTMENT

  1. Perform the camera aiming. Refer to Work Procedure.

  2. Erase all self-diagnosis results with CONSULT.

  3. Perform “All DTC Reading”.

  4. Check if the “C2503-54” is detected in “Self Diagnostic Result” of “LANE CAMERA”.

Is “C2503-54” detected?

YES>>

Replace the front camera unit. Refer to Removal and Installation.

NO>>

INSPECTION END

C2503-78 Configuration

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2503-78

Configuration data error

(Configuration data error)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Configuration of the front camera unit is incomplete
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Configuration of the front camera unit is not completed

  • Front camera unit

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2503-78” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2503-78” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM CONFIGURATION OF FRONT CAMERA UNIT

  1. Perform configuration of the front camera unit. Refer to Work Procedure.

  2. Erases self-diagnosis results.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC “C2503-78” detected?

YES>>

Replace the front camera unit. Refer to Removal and Installation.

NO>>

INSPECTION END

C2504-71 Configuration

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2504-71

Configuration data error

(Configuration data error)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Configuration of the front camera unit is incomplete
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Configuration of the front camera unit is not completed

  • Front camera unit

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2504-71” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2504-71” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM CONFIGURATION OF FRONT CAMERA UNIT

  1. Perform configuration of the front camera unit. Refer to Work Procedure.

  2. Erases self-diagnosis results.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC “C2504-71” detected?

YES>>

Replace the front camera unit. Refer to Removal and Installation.

NO>>

INSPECTION END

C2505-92 Configuration

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2505-92

Configuration data error

(Configuration data error)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Configuration of the front camera unit is incomplete
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Configuration of the front camera unit is not completed

  • Front camera unit

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2505-92” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2505-92” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM CONFIGURATION OF FRONT CAMERA UNIT

  1. Perform configuration of the front camera unit. Refer to Work Procedure.

  2. Erases self-diagnosis results.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC “C2505-92” detected?

YES>>

Replace the front camera unit. Refer to Removal and Installation.

NO>>

INSPECTION END

C2506-49 Front Camera Unit

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2506-49

Front camera unit

(Front camera unit)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold
  • Configuration of the front camera unit is not completed.

  • If front camera unit is malfunctioning

Diagnosis delay time 1 seconds or more

POSSIBLE CAUSE

  • Configuration of the front camera unit is not completed.

  • Front camera unit

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2506-49” is detected as the current malfunction in “Self Diagnostic Result” of “LANE CAMERA”.

Is “C2506-49” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

IGNITION SWITCH OFF TO ON

  1. Ignition switch OFF to ON 5 times.

  2. Check if the “C2506-49” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2506-49” detected as the current malfunction?

YES>>

Replace the front camera unit. Refer to Removal and Installation.

NO>>

INSPECTION END

C2507-16 Power Supply Circuit

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2507-16

Power supply circuit

(Power supply circuit)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Front camera unit ignition voltage is greater than 16V
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Harness, connector, or fuse

  • Front camera unit

  • Power supply circuit

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2507-16” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2507-16” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK FRONT CAMERA UNIT SUPPLY AND GROUND CIRCUIT

Check power supply and ground circuit of front camera unit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

Replace the front camera unit. Refer to Removal and Installation.

NO>>

Repair or replace harness or connectors.

C2507-17 Power Supply Circuit

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2507-17

Power supply circuit

(Power supply circuit)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Front camera unit ignition voltage is greater than 16V
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Harness, connector, or fuse

  • Front camera unit

  • Power supply circuit

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2507-17” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2507-17” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK FRONT CAMERA UNIT SUPPLY AND GROUND CIRCUIT

Check power supply and ground circuit of front camera unit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

Replace the front camera unit. Refer to Removal and Installation.

NO>>

Repair or replace harness or connectors.

C2520-82 Bcm

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2520-82

BCM

(Body control module)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Front camera unit detects that BCM has a malfunction.
Diagnosis delay time 1 seconds or more

POSSIBLE CAUSE

BCM

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC “C2520-82” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2520-82” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2520-82” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2 >>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC “C2520-82” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

CHECK BCM SELF DIAGNOSTIC RESULT

Perform “Self Diagnostic Result” of “BCM” using CONSULT.

Are any DTCs detected?

YES>>

Refer to DTC Index .

NO>>

Replace front camera unit. Refer to Removal and Installation.

C2520-83 Bcm

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2520-83

BCM

(Body control module)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Front camera unit detects that BCM has a malfunction.
Diagnosis delay time 1 seconds or more

POSSIBLE CAUSE

BCM

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC “C2520-83” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2520-83” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2520-83” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2 >>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC “C2520-83” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

CHECK BCM SELF DIAGNOSTIC RESULT

Perform “Self Diagnostic Result” of “BCM” using CONSULT.

Are any DTCs detected?

YES>>

Refer to DTC Index.

NO>>

Replace front camera unit. Refer to Removal and Installation.

C2520-86 Bcm

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2520-86

BCM

(Body control module)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Front camera unit detects that BCM has a malfunction.
Diagnosis delay time 1 seconds or more

POSSIBLE CAUSE

BCM

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC “C2520-86” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2520-86” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2520-86” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1 >>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC “C2520-86” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

CHECK BCM SELF DIAGNOSTIC RESULT

Perform “Self Diagnostic Result” of “BCM” using CONSULT.

Are any DTCs detected?

YES>>

Refer to DTC Index.

NO>>

Replace front camera unit. Refer to Removal and Installation.

C2520-87 Bcm

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2520-87

BCM

(Body control module)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Front camera unit detects that BCM has a malfunction.
Diagnosis delay time 1 seconds or more

POSSIBLE CAUSE

BCM

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC “C2520-87” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2520-87” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2520-87” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1 >>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC “C2520-87” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

CHECK BCM SELF DIAGNOSTIC RESULT

Perform “Self Diagnostic Result” of “BCM” using CONSULT.

Are any DTCs detected?

YES>>

Refer to DTC Index.

NO>>

Replace front camera unit. Refer to Removal and Installation.

C2521-82 Ecm

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2521-82

ECM

(Engine control module)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Front camera unit detects that ECM has a malfunction.
Diagnosis delay time 1 seconds or more

POSSIBLE CAUSE

ECM

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC “C2521-82” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2521-82” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2521-82” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC “C2521-82” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

CHECK ECM SELF DIAGNOSTIC RESULT

Perform “Self Diagnostic Result” of “ENGINE” using CONSULT.

Are any DTCs detected?

YES>>

Refer to DTC Index.

NO>>

Replace front camera unit. Refer to Removal and Installation.

C2521-83 Ecm

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2521-83

ECM

(Engine control module)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Front camera unit detects that ECM has a malfunction.
Diagnosis delay time 1 seconds or more

POSSIBLE CAUSE

ECM

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC “C2521-83” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2521-83” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2521-83” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1 >>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2 >>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC “C2521-83” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

CHECK ECM SELF DIAGNOSTIC RESULT

Perform “Self Diagnostic Result” of “ENGINE” using CONSULT.

Are any DTCs detected?

YES>>

Refer to DTC Index.

NO>>

Replace front camera unit. Refer to Removal and Installation.

C2521-86 Ecm

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2521-86

ECM

(Engine control module)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Front camera unit detects that ECM has a malfunction.
Diagnosis delay time 1 seconds or more

POSSIBLE CAUSE

ECM

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC “C2521-86” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2521-86” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2521-86” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2 >>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC “C2521-86” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

CHECK ECM SELF DIAGNOSTIC RESULT

Perform “Self Diagnostic Result” of “ENGINE” using CONSULT.

Are any DTCs detected?

YES>>

Refer to DTC Index.

NO>>

Replace front camera unit. Refer to Removal and Installation.

C2521-87 Ecm

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2521-87

ECM

(Engine control module)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Front camera unit detects that ECM has a malfunction.
Diagnosis delay time 1 seconds or more

POSSIBLE CAUSE

ECM

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC “C2521-87” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2521-87” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2521-87” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1 >>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2 >>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC “C2521-87” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

CHECK ECM SELF DIAGNOSTIC RESULT

Perform “Self Diagnostic Result” of “ENGINE” using CONSULT.

Are any DTCs detected?

YES>>

Refer to DTC Index.

NO>>

Replace front camera unit. Refer to Removal and Installation.

C2522-82 Abs

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2522-82

ABS

(Anti-lock braking system)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Front camera unit detects that ABS actuator and electric unit (control unit) has a malfunction.
Diagnosis delay time 1 seconds or more

POSSIBLE CAUSE

ABS actuator and electric unit (control unit)

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC “C2522-82” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2522-82” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2522-82” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1 >>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC “C2522-82” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF DIAGNOSTIC RESULT

Perform “Self Diagnostic Result” of “ABS” using CONSULT.

Are any DTCs detected?

YES>>

Refer to DTC Index.

NO>>

Replace front camera unit. Refer to Removal and Installation.

C2522-83 Abs

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2522-83

ABS

(Anti-lock braking system)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Front camera unit detects that ABS actuator and electric unit (control unit) has a malfunction.
Diagnosis delay time 1 seconds or more

POSSIBLE CAUSE

ABS actuator and electric unit (control unit)

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC “C2522-83” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2522-83” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2522-83” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1 >>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC “C2522-83” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF DIAGNOSTIC RESULT

Perform “Self Diagnostic Result” of “ABS” using CONSULT.

Are any DTCs detected?

YES>>

Refer to DTC Index.

NO>>

Replace front camera unit. Refer to Removal and Installation.

C2522-86 Abs

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2522-86

ABS

(Anti-lock braking system)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Front camera unit detects that ABS actuator and electric unit (control unit) has a malfunction.
Diagnosis delay time 1 seconds or more

POSSIBLE CAUSE

ABS actuator and electric unit (control unit)

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC “C2522-86” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2522-86” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2522-86” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1 >>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC “C2522-86” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF DIAGNOSTIC RESULT

Perform “Self Diagnostic Result” of “ABS” using CONSULT.

Are any DTCs detected?

YES>>

Refer to DTC Index.

NO>>

Replace front camera unit. Refer to Removal and Installation.

C2522-87 Abs

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2522-87

ABS

(Anti-lock braking system)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Front camera unit detects that ABS actuator and electric unit (control unit) has a malfunction.
Diagnosis delay time 1 seconds or more

POSSIBLE CAUSE

ABS actuator and electric unit (control unit)

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC “C2522-87” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2522-87” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2522-87” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1 >>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2 >>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC “C2522-87” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF DIAGNOSTIC RESULT

Perform “Self Diagnostic Result” of “ABS” using CONSULT.

Are any DTCs detected?

YES>>

Refer to DTC Index.

NO>>

Replace front camera unit. Refer to Removal and Installation.

C2523-86 Combination Meter

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2523-86

Combination meter

(Combination meter)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Front camera unit detects that combination meter has a malfunction.
Diagnosis delay time 1 seconds or more

POSSIBLE CAUSE

Combination meter

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC “C2523-86” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2523-86” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2523-86” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC “C2523-86” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

CHECK COMBINATION METER SELF DIAGNOSTIC RESULT

Perform “Self Diagnostic Result” of “METER/M&A” using CONSULT.

Are any DTCs detected?

YES>>

Refer to DTC Index(FULL TFT METER) or DTC Index(7 information display).

NO>>

Replace front camera unit. Refer to Removal and Installation.

C2523-87 Combination Meter

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2523-87

Combination meter

(Combination meter)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Front camera unit detects that combination meter has a malfunction.
Diagnosis delay time 1 seconds or more

POSSIBLE CAUSE

Combination meter

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC “C2523-87” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2523-87” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2523-87” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC “C2523-87” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

CHECK COMBINATION METER SELF DIAGNOSTIC RESULT

Perform “Self Diagnostic Result” of “METER/M&A” using CONSULT.

Are any DTCs detected?

YES>>

Refer to DTC Index(FULL TFT METER) or DTC Index(7 information display).

NO>>

Replace front camera unit. Refer to Removal and Installation.

C2524-82 Configuration

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2524-82

Configuration data error

(Configuration data error)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Configuration of the front camera unit is incomplete
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Configuration of the front camera unit is not completed

  • Front camera unit

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2524-82” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2524-82” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM CONFIGURATION OF FRONT CAMERA UNIT

  1. Perform configuration of the front camera unit. Refer to Work Procedure.

  2. Erases self-diagnosis results.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC “C2524-82” detected?

YES>>

Replace the front camera unit. Refer to Removal and Installation.

NO>>

INSPECTION END

C2524-83 Configuration

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2524-83

Configuration data error

(Configuration data error)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Configuration of the front camera unit is incomplete
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Configuration of the front camera unit is not completed

  • Front camera unit

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2524-83” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2524-83” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM CONFIGURATION OF FRONT CAMERA UNIT

  1. Perform configuration of the front camera unit. Refer to Work Procedure.

  2. Erases self-diagnosis results.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC “C2524-83” detected?

YES>>

Replace the front camera unit. Refer to Removal and Installation.

NO>>

INSPECTION END

C2524-86 Configuration

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2524-86

Configuration data error

(Configuration data error)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Configuration of the front camera unit is incomplete
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Configuration of the front camera unit is not completed

  • Front camera unit

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2524-86” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2524-86” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM CONFIGURATION OF FRONT CAMERA UNIT

  1. Perform configuration of the front camera unit. Refer to Work Procedure.

  2. Erases self-diagnosis results.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC “C2524-86” detected?

YES>>

Replace the front camera unit. Refer to Removal and Installation.

NO>>

INSPECTION END

C2524-87 Configuration

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2524-87

Configuration data error

(Configuration data error)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Configuration of the front camera unit is incomplete
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Configuration of the front camera unit is not completed

  • Front camera unit

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2524-87” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2524-87” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM CONFIGURATION OF FRONT CAMERA UNIT

  1. Perform configuration of the front camera unit. Refer to Work Procedure.

  2. Erases self-diagnosis results.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC “C2524-87” detected?

YES>>

Replace the front camera unit. Refer to Removal and Installation.

NO>>

INSPECTION END

C2525-86 Av Control Unit

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2525-86

AV control unit

(Audio visual control unit)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Front camera unit detects that AV control unit has a malfunction.
Diagnosis delay time 1 seconds or more

POSSIBLE CAUSE

AV control unit

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC “C2525-86” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2525-86” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2525-86” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1 >>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2 >>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC “C2525-86” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

CHECK AV CONTROL UNIT SELF DIAGNOSTIC RESULT

Perform “Self Diagnostic Result” of “MULTI AV” using CONSULT.

Are any DTCs detected?

YES>>

Refer to DTC Index.

NO>>

Replace front camera unit. Refer to Removal and Installation.

C2525-87 Av Control Unit

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2525-87

AV control unit

(Audio visual control unit)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Front camera unit detects that AV control unit has a malfunction.
Diagnosis delay time 1 seconds or more

POSSIBLE CAUSE

AV control unit

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC “C2525-87” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2525-87” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2525-87” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2 >>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC “C2525-87” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

CHECK AV CONTROL UNIT SELF DIAGNOSTIC RESULT

Perform “Self Diagnostic Result” of “MULTI AV” using CONSULT.

Are any DTCs detected?

YES>>

Refer to DTC Index.

NO>>

Replace front camera unit. Refer to Removal and Installation.

C2526-82 Adas Control Unit

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2526-82

ADAS control unit

(Advanced driver assistance systems control unit)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Front camera unit detects that ADAS control unit 2 has a malfunction.
Diagnosis delay time 1 seconds or more

POSSIBLE CAUSE

ADAS control unit 2

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC “C2526-82” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2526-82” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2526-82” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC “C2526-82” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

CHECK ADAS CONTROL UNIT 2 SELF DIAGNOSTIC RESULT

Perform “Self Diagnostic Result” of “ICC/ADAS 2” using CONSULT.

Are any DTCs detected?

YES>>

Refer to DTC Index.

NO>>

Replace front camera unit. Refer to Removal and Installation.

C2526-83 Adas Control Unit

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2526-83

ADAS control unit

(Advanced driver assistance systems control unit)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Front camera unit detects that ADAS control unit 2 has a malfunction.
Diagnosis delay time 1 seconds or more

POSSIBLE CAUSE

ADAS control unit 2

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC “C2526-83” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2526-83” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2526-83” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC “C2526-83” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

CHECK ADAS CONTROL UNIT 2 SELF DIAGNOSTIC RESULT

Perform “Self Diagnostic Result” of “ICC/ADAS 2” using CONSULT.

Are any DTCs detected?

YES>>

Refer to DTC Index.

NO>>

Replace front camera unit. Refer to Removal and Installation.

C2526-86 Adas Control Unit

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2526-86

ADAS control unit

(Advanced driver assistance systems control unit)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Front camera unit detects that ADAS control unit 2 has a malfunction.
Diagnosis delay time 1 seconds or more

POSSIBLE CAUSE

ADAS control unit 2

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC “C2526-86” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2526-86” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2526-86” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1 >>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2 >>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC “C2526-86” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

CHECK ADAS CONTROL UNIT 2 SELF DIAGNOSTIC RESULT

Perform “Self Diagnostic Result” of “ICC/ADAS 2” using CONSULT.

Are any DTCs detected?

YES>>

Refer to DTC Index.

NO>>

Replace front camera unit. Refer to Removal and Installation.

C2526-87 Adas Control Unit

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2526-87

ADAS control unit

(Advanced driver assistance systems control unit)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Front camera unit detects that ADAS control unit 2 has a malfunction.
Diagnosis delay time 1 seconds or more

POSSIBLE CAUSE

ADAS control unit 2

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC “C2526-87” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2526-87” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2526-87” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC “C2526-87” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

CHECK ADAS CONTROL UNIT 2 SELF DIAGNOSTIC RESULT

Perform “Self Diagnostic Result” of “ICC/ADAS 2” using CONSULT.

Are any DTCs detected?

YES>>

Refer to DTC Index.

NO>>

Replace front camera unit. Refer to Removal and Installation.

C2527-82 Tcm

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2527-82

TCM

(Transmission control module)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Front camera unit detects that TCM has a malfunction.
Diagnosis delay time 1 seconds or more

POSSIBLE CAUSE

TCM

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC “C2527-82” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2527-82” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2527-82” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1 >>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC “C2527-82” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

CHECK TCM SELF DIAGNOSTIC RESULT

Perform “Self Diagnostic Result” of “TRANSMISSION” using CONSULT.

Are any DTCs detected?

YES>>

Refer to DTC Index.

NO>>

Replace front camera unit. Refer to Removal and Installation.

C2527-83 Tcm

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2527-83

TCM

(Transmission control module)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Front camera unit detects that TCM has a malfunction.
Diagnosis delay time 1 seconds or more

POSSIBLE CAUSE

TCM

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC “C2527-83” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2527-83” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2527-83” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC “C2527-83” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

CHECK TCM SELF DIAGNOSTIC RESULT

Perform “Self Diagnostic Result” of “TRANSMISSION” using CONSULT.

Are any DTCs detected?

YES>>

Refer to DTC Index.

NO>>

Replace front camera unit. Refer to Removal and Installation.

C2527-86 Tcm

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2527-86

TCM

(Transmission control module)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Front camera unit detects that TCM has a malfunction.
Diagnosis delay time 1 seconds or more

POSSIBLE CAUSE

TCM

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC “C2527-86” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2527-86” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2527-86” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2 >>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC “C2527-86” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

CHECK TCM SELF DIAGNOSTIC RESULT

Perform “Self Diagnostic Result” of “TRANSMISSION” using CONSULT.

Are any DTCs detected?

YES>>

Refer to DTC Index.

NO>>

Replace front camera unit. Refer to Removal and Installation.

C2527-87 Tcm

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2527-87

TCM

(Transmission control module)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Front camera unit detects that TCM has a malfunction.
Diagnosis delay time 1 seconds or more

POSSIBLE CAUSE

TCM

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC “C2527-87” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2527-87” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2527-87” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1 >>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC “C2527-87” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

CHECK TCM SELF DIAGNOSTIC RESULT

Perform “Self Diagnostic Result” of “TRANSMISSION” using CONSULT.

Are any DTCs detected?

YES>>

Refer to DTC Index.

NO>>

Replace front camera unit. Refer to Removal and Installation.

C2528-82 Ipdm E/r

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2528-82

IPDM E/R

(Intelligent power distribution module engine room)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Front camera unit detects that IPDM E/R has a malfunction.
Diagnosis delay time 1 seconds or more

POSSIBLE CAUSE

IPDM E/R

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC “C2528-82” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2528-82” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2528-82” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC “C2528-82” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

CHECK IPDM E/R SELF DIAGNOSTIC RESULT

Perform “Self Diagnostic Result” of “ IPDM E/R” using CONSULT.

Are any DTCs detected?

YES>>

Refer to DTC Index.

NO>>

Replace front camera unit. Refer to Removal and Installation.

C2528-83 Ipdm E/r

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2528-83

IPDM E/R

(Intelligent power distribution module engine room)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Front camera unit detects that IPDM E/R has a malfunction.
Diagnosis delay time 1 seconds or more

POSSIBLE CAUSE

IPDM E/R

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC “C2528-83” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2528-83” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2528-83” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2 >>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC “C2528-83” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

CHECK IPDM E/R SELF DIAGNOSTIC RESULT

Perform “Self Diagnostic Result” of “ IPDM E/R” using CONSULT.

Are any DTCs detected?

YES>>

Refer to DTC Index.

NO>>

Replace front camera unit. Refer to Removal and Installation.

C2528-86 Ipdm E/r

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2528-86

IPDM E/R

(Intelligent power distribution module engine room)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Front camera unit detects that IPDM E/R has a malfunction.
Diagnosis delay time 1 seconds or more

POSSIBLE CAUSE

IPDM E/R

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC “C2528-86” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2528-86” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2528-86” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1 >>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC “C2528-86” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

CHECK IPDM E/R SELF DIAGNOSTIC RESULT

Perform “Self Diagnostic Result” of “ IPDM E/R” using CONSULT.

Are any DTCs detected?

YES>>

Refer to DTC Index.

NO>>

Replace front camera unit. Refer to Removal and Installation.

C2528-87 Ipdm E/r

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2528-87

IPDM E/R

(Intelligent power distribution module engine room)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Front camera unit detects that IPDM E/R has a malfunction.
Diagnosis delay time 1 seconds or more

POSSIBLE CAUSE

IPDM E/R

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC “C2528-87” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2528-87” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2528-87” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1 >>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2 >>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC “C2528-87” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

CHECK IPDM E/R SELF DIAGNOSTIC RESULT

Perform “Self Diagnostic Result” of “ IPDM E/R” using CONSULT.

Are any DTCs detected?

YES>>

Refer to DTC Index.

NO>>

Replace front camera unit. Refer to Removal and Installation.

C2529-86 Air Bag Diagnosis Sensor Unit

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2529-86

Air bag diagnosis sensor unit

(Air bag diagnosis sensor unit)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Front camera unit detects that air bag diagnosis sensor unit has a malfunction.
Diagnosis delay time 1 seconds or more

POSSIBLE CAUSE

Air bag diagnosis sensor unit

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC “C2529-86” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2529-86” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2529-86” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC “C2529-86” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

CHECK AIR BAG DIAGNOSIS SENSOR UNIT SELF DIAGNOSTIC RESULT

Perform “Self Diagnostic Result” of “AIR BAG” using CONSULT.

Are any DTCs detected?

YES>>

Refer to DTC Index .

NO>>

Replace front camera unit. Refer to Removal and Installation.

C2529-87 Air Bag Diagnosis Sensor Unit

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2529-87

Air bag diagnosis sensor unit

(Air bag diagnosis sensor unit)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Front camera unit detects that air bag diagnosis sensor unit has a malfunction.
Diagnosis delay time 1 seconds or more

POSSIBLE CAUSE

Air bag diagnosis sensor unit

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC “C2529-87” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2529-87” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2529-87” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1 >>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2 >>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC “C2529-87” is displayed with Network-DTC, first diagnose the Network-DTC.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2 .

CHECK AIR BAG DIAGNOSIS SENSOR UNIT SELF DIAGNOSTIC RESULT

Perform “Self Diagnostic Result” of “AIR BAG” using CONSULT.

Are any DTCs detected?

YES>>

Refer to DTC Index .

NO>>

Replace front camera unit. Refer to Removal and Installation.

C2531-86 Configuration

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2531-86

Configuration data error

(Configuration data error)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Configuration of the front camera unit is incomplete
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Configuration of the front camera unit is not completed

  • Front camera unit

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2531-86” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2531-86” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM CONFIGURATION OF FRONT CAMERA UNIT

  1. Perform configuration of the front camera unit. Refer to Work Procedure.

  2. Erases self-diagnosis results.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC “C2531-86” detected?

YES>>

Replace the front camera unit. Refer to Removal and Installation.

NO>>

INSPECTION END

C2531-87 Configuration

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2531-87

Configuration data error

(Configuration data error)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Configuration of the front camera unit is incomplete
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Configuration of the front camera unit is not completed

  • Front camera unit

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2531-87” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2531-87” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM CONFIGURATION OF FRONT CAMERA UNIT

  1. Perform configuration of the front camera unit. Refer to Work Procedure.

  2. Erases self-diagnosis results.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC “C2531-87” detected?

YES>>

Replace the front camera unit. Refer to Removal and Installation.

NO>>

INSPECTION END

C2570-4b Configuration

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2570-4B

Configuration data error

(Configuration data error)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Configuration of the front camera unit is incomplete
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Configuration of the front camera unit is not completed

  • Front camera unit

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2570-4B” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2570-4B” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM CONFIGURATION OF FRONT CAMERA UNIT

  1. Perform configuration of the front camera unit. Refer to Work Procedure.

  2. Erases self-diagnosis results.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC “C2570-4B” detected?

YES>>

Replace the front camera unit. Refer to Removal and Installation.

NO>>

INSPECTION END

C2571-71 Configuration

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2571-71

Configuration data error

(Configuration data error)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Configuration of the front camera unit is incomplete
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Configuration of the front camera unit is not completed

  • Front camera unit

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2571-71” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2571-71” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM CONFIGURATION OF FRONT CAMERA UNIT

  1. Perform configuration of the front camera unit. Refer to Work Procedure.

  2. Erases self-diagnosis results.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC “C2571-71” detected?

YES>>

Replace the front camera unit. Refer to Removal and Installation.

NO>>

INSPECTION END

C2572-71 Configuration

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2572-71

Configuration data error

(Configuration data error)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Configuration of the front camera unit is incomplete
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Configuration of the front camera unit is not completed

  • Front camera unit

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2572-71” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2572-71” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM CONFIGURATION OF FRONT CAMERA UNIT

  1. Perform configuration of the front camera unit. Refer to Work Procedure.

  2. Erases self-diagnosis results.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC “C2572-71” detected?

YES>>

Replace the front camera unit. Refer to Removal and Installation.

NO>>

INSPECTION END

C2573-97 Configuration

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2573-97

Configuration data error

(Configuration data error)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Configuration of the front camera unit is incomplete
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Configuration of the front camera unit is not completed

  • Front camera unit

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2573-97” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2573-97” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM CONFIGURATION OF FRONT CAMERA UNIT

  1. Perform configuration of the front camera unit. Refer to Work Procedure.

  2. Erases self-diagnosis results.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC “C2573-97” detected?

YES>>

Replace the front camera unit. Refer to Removal and Installation.

NO>>

INSPECTION END

C2575-92 Configuration

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2575-92

Configuration data error

(Configuration data error)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Configuration of the front camera unit is incomplete
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Configuration of the front camera unit is not completed

  • Front camera unit

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2575-92” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2575-92” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM CONFIGURATION OF FRONT CAMERA UNIT

  1. Perform configuration of the front camera unit. Refer to Work Procedure.

  2. Erases self-diagnosis results.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC “C2575-92” detected?

YES>>

Replace the front camera unit. Refer to Removal and Installation.

NO>>

INSPECTION END

C2576-97 Configuration

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
C2576-97

Configuration data error

(Configuration data error)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Configuration of the front camera unit is incomplete
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Configuration of the front camera unit is not completed

  • Front camera unit

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “C2576-97” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “C2576-97” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM CONFIGURATION OF FRONT CAMERA UNIT

  1. Perform configuration of the front camera unit. Refer to Work Procedure.

  2. Erases self-diagnosis results.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC “C2576-97” detected?

YES>>

Replace the front camera unit. Refer to Removal and Installation.

NO>>

INSPECTION END

U2104-87 Configuration

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U2104-87

Configuration data error

(Configuration data error)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Configuration of the front camera unit is incomplete
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Configuration of the front camera unit is not completed

  • Front camera unit

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “U2104-87” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “U2104-87” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM CONFIGURATION OF FRONT CAMERA UNIT

  1. Perform configuration of the front camera unit. Refer to Work Procedure.

  2. Erases self-diagnosis results.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC “U2104-87” detected?

YES>>

Replace the front camera unit. Refer to Removal and Installation.

NO>>

INSPECTION END

U2140-87 Can Comm Circuit

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U2140-87

CAN comm err (ECM)

[Controller area network communication error (Engine control module)]
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold If front camera unit is not transmitting or receiving CAN communication signal
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “U2140-87” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “U2140-87” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2 >>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM SELF DIAGNOSTIC

  1. Start the engine.

  2. Erases DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is “U2140-87” detected?

YES>>

Refer to Trouble Diagnosis Flow Chart.

NO>>

INSPECTION END

U2141-87 Can Comm Circuit

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U2141-87

CAN comm err (TCM)

[Controller area network communication error (Transmission control module)]
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold If front camera unit is not transmitting or receiving CAN communication signal
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “U2141-87” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “U2141-87” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2 >>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM SELF DIAGNOSTIC

  1. Start the engine.

  2. Erases DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is “U2141-87” detected?

YES>>

Refer to Trouble Diagnosis Flow Chart.

NO>>

INSPECTION END

U2142-87 Configuration

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U2142-87

Configuration data error

(Configuration data error)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Configuration of the front camera unit is incomplete
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Configuration of the front camera unit is not completed

  • Front camera unit

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “U2142-87” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “U2142-87” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM CONFIGURATION OF FRONT CAMERA UNIT

  1. Perform configuration of the front camera unit. Refer to Work Procedure.

  2. Erases self-diagnosis results.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC “U2142-87” detected?

YES>>

Replace the front camera unit. Refer to Removal and Installation.

NO>>

INSPECTION END

U2148-87 Can Comm Circuit

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U2148-87

CAN comm err (brake control unit)

[Controller area network communication error (brake control unit)]
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold If front camera unit is not transmitting or receiving CAN communication signal
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “U2148-87” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “U2148-87” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1 >>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2 >>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM SELF DIAGNOSTIC

  1. Start the engine.

  2. Erases DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description .

Is “U2148-87” detected?

YES>>

Refer to Trouble Diagnosis Flow Chart.

NO>>

INSPECTION END

U214e-87 Can Comm Circuit

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U214E-87

CAN comm err (combination meter)

[Controller area network communication error (combination meter)]
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold If front camera unit is not transmitting or receiving CAN communication signal
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “U214E-87” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “U214E-87” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1 >>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2 >>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM SELF DIAGNOSTIC

  1. Start the engine.

  2. Erases DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is “U214E-87” detected?

YES>>

Refer to Trouble Diagnosis Flow Chart.

NO>>

INSPECTION END

U214f-87 Can Comm Circuit

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U214F-87

CAN comm err (BCM)

[Controller area network communication error (Body control module)]
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold If front camera unit is not transmitting or receiving CAN communication signal
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “U214F-87” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “U214F-87” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1 >>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM SELF DIAGNOSTIC

  1. Start the engine.

  2. Erases DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is “U214F-87” detected?

YES>>

Refer to Trouble Diagnosis Flow Chart.

NO>>

INSPECTION END

U2150-87 Can Comm Circuit

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U2150-87

CAN comm err (AIRBAG)

[Controller area network communication error (Airbag)]
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold If front camera unit is not transmitting or receiving CAN communication signal
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “U2150-87” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “U2150-87” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1 >>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2 >>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM SELF DIAGNOSTIC

  1. Start the engine.

  2. Erases DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is “U2150-87” detected?

YES>>

Refer to Trouble Diagnosis Flow Chart.

NO>>

INSPECTION END

U2152-87 Can Comm Circuit

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U2152-87

CAN comm err (ADAS control unit)

[Controller area network communication error (Advanced driver assistance systems control unit)]
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold If front camera unit is not transmitting or receiving CAN communication signal
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “U2152-87” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “U2152-87” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1 >>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2 >>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM SELF DIAGNOSTIC

  1. Start the engine.

  2. Erases DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is “U2152-87” detected?

YES>>

Refer to Trouble Diagnosis Flow Chart.

NO>>

INSPECTION END

U2154-87 Can Comm Circuit

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U2154-87

CAN comm err (MIU)

[Controller area network communication error (Multimedia interface unit)]
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold If front camera unit is not transmitting or receiving CAN communication signal
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “U2154-87” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “U2154-87” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1 >>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2 >>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM SELF DIAGNOSTIC

  1. Start the engine.

  2. Erases DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is “U2154-87” detected?

YES>>

Refer to Trouble Diagnosis Flow Chart.

NO>>

INSPECTION END

U2156-87 Configuration

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U2156-87

Configuration data error

(Configuration data error)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold Configuration of the front camera unit is incomplete
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

  • Configuration of the front camera unit is not completed

  • Front camera unit

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “U2156-87” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “U2156-87” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM CONFIGURATION OF FRONT CAMERA UNIT

  1. Perform configuration of the front camera unit. Refer to Work Procedure.

  2. Erases self-diagnosis results.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC “U2156-87” detected?

YES>>

Replace the front camera unit. Refer to Removal and Installation.

NO>>

INSPECTION END

U215b-87 Can Comm Circuit

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U215B-87

CAN comm err (IPDM E/R)

[Controller area network communication error (Intelligent power distribution module engine room)]
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold If front camera unit is not transmitting or receiving CAN communication signal
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “U215B-87” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “U215B-87” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1 >>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2 >>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM SELF DIAGNOSTIC

  1. Start the engine.

  2. Erases DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is “U215B-87” detected?

YES>>

Refer to Trouble Diagnosis Flow Chart.

NO>>

INSPECTION END

U276b-88 Ethernet Circuit

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U276B 88

Ethernet circuit

(Ethernet circuit)
Diagnosis condition When engine is running
Signal (terminal) Ethernet
Threshold If front camera unit is not receiving ethernet communication signal from ADAS control unit 2
Diagnosis delay time 5 seconds or more

POSSIBLE CAUSE

  • Ethernet harness

  • ADAS control unit 2

  • Front camera unit

FAIL-SAFE

The following systems are canceled.

  • Vehicle-to-vehicle distance control mode

  • Conventional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine and wait at least 5 seconds.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the DTC “U276B-88” is detected as the current malfunction in “Self Diagnostic Result” of “LANE CAMERA”.

Is DTC “U276B-88” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1 >>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK CONNECTOR

  1. Ignition switch OFF.

  2. Check the ethernet harness connectors and terminals of front camera unit and ADAS control unit 2 for damage or looseness.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace the malfunction part, securely lock the harness connector.

PERFORM ALL DTC READING

  1. Ignition switch ON.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if any DTCs of ethernet (DTC “C1F70-87”, “U2852-87” and/or “U2852-88”) are detected in “Self Diagnostic Result” of “ICC/ADAS 2”

Are any DTCs of ethernet detected?

YES>>

Replace the ADAS control unit 2 (Refer to Removal and Installation.), and GO TO 3.

NO>>

Replace the ADAS control unit 2. Refer to Removal and Installation.

PERFORM DTC CONFIRMATION PROCEDURE-1

  1. Erases all self-diagnosis results with CONSULT.

  2. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC “U276B-88” detected as the current malfunction?

YES>>

Replace the front camera unit (Refer to Removal and Installation.), and GO TO 4.

NO>>

INSPECTION END

PERFORM DTC CONFIRMATION PROCEDURE-2

  1. Erases all self-diagnosis results with CONSULT.

  2. Perform DTC confirmation procedure again. Refer to DTC Description.

Is DTC “U276B-88” detected as the current malfunction?

YES>>

Replace the ethernet harness between front camera unit and ADAS control unit 2.

NO>>

INSPECTION END

U2a07-88 Can Comm Circuit

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
U2A07-88

CAN comm circuit

(Controller area network communication circuit)
Diagnosis condition When ignition switch is ON.
Signal (terminal) -
Threshold If front camera unit is not transmitting or receiving CAN communication signal
Diagnosis delay time 2 seconds or more

POSSIBLE CAUSE

CAN communication system

FAIL-SAFE

The following functions are suspended.

  • Vehicle-to-vehicle distance control mode

  • Conven tional (fixed speed) cruise control mode

  • Steering wheel assistance function

  • AEB

  • LDW

  • I-LI

  • I-BSI

  • TSR

CONFIRMATION PROCEDURE

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine.

  2. Perform “All DTC Reading” with CONSULT.

  3. Check if the “U2A07-88” is detected as the current malfunction on the self-diagnosis results of “LANE CAMERA”.

Is “U2A07-88” detected as the current malfunction?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1 >>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2 >>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

PERFORM SELF DIAGNOSTIC

  1. Start the engine.

  2. Erases DTC.

  3. Perform DTC confirmation procedure again. Refer to DTC Description.

Is “U2A07-88” detected?

YES>>

Refer to Trouble Diagnosis Flow Chart.

NO>>

INSPECTION END