Dtc/circuit Diagnosis (P026b Injection Timing ... P0420 Three Way Catalyst Function)

In this manual: Dtc/circuit Diagnosis (P026b Injection Timing ... P0420 Three Way Catalyst Function)
General Information — 8Engine :: Engine Mechanical — 19Engine Lubrication System - Precautions. Preparation — 1Engine Lubrication System - Lubrication System (System Description). Engine Oil Pressure (Basic Inspection). Service Data and Specifications (SDS) — 1Engine Cooling System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Engine Cooling System - Engine Coolant — 1Engine Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Engine Control System - Ecu Diagnosis Information — 1Ecu Diagnosis Information - Ecm ++ — 1Engine Control System - Basic Inspection — 1Basic Inspection - Diagnosis and Repair Workflow ++ — 1Basic Inspection - Basic Inspection ++ — 1Basic Inspection - Additional Service When Replacing Ecm ++ — 1Basic Inspection - Fuel Pressure Check ++ — 1Basic Inspection - How to Set Srt Code ++ — 1Basic Inspection - How to Erase Permanent Dtc ++ — 1Engine Control System - Dtc/circuit Diagnosis — 1Engine Control System - Symptom Diagnosis — 1Engine Control System - Periodic Maintenance — 1Engine Control System - Removal and Installation — 1Fuel System - Precautions. Preparation. Service Data and Specifications (SDS) — 1Fuel System - Fuel System (Periodic Maintenance). Fuel Level Sensor Unit (Disassembly and Assembly) — 1Exhaust System - Precautions. Preparation — 1Exhaust System - Exhaust System (Periodic Maintenance). Exhaust System (Removal and Installation) — 1Starting System - Precautions. Preparation. Starter Motor (Service Data and Specifications (sds)) — 1Starting System - Diagnosis and Repair Work Flow — 1Starting System - Starting System (Symptom Diagnosis). Starter Motor (Removal and Installation) — 1Accelerator Control System - Precautions. Service Data and Specifications (SDS) — 1Accelerator Control System - Accelerator Pedal Assembly — 1Transmission & Driveline :: Transaxle & Transmission — 21Driveline - System Description — 1Transfer: Ty92b - Ecu Diagnosis Information. Awd Control Unit ++ — 1Driveline - Basic Inspection — 1Driveline - Dtc/circuit Diagnosis — 1Driveline - Symptom Diagnosis — 1Driveline - Removal and Installation — 1Transfer: Ty92b - Unit Removal and Installation. Transfer Assembly ++ — 1Driveline - Unit Disassembly and Assembly — 1Driveline - Basic Inspection — 1Driveline - Removal and Installation — 1Driveline - Unit Disassembly and Assembly — 1Front Axle - Precautions. Preparation — 1Front Axle - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Front Axle - Front Drive Shaft Boot — 1Front Axle - Front Drive Shaft — 1Rear Axle - Precautions. Preparation. Service Data and Specifications (SDS) — 1Rear Axle - Noise, Vibration and Harshness (nvh) Troubleshooting — 1Rear Axle - Rear Drive Shaft — 1Suspension :: Front Suspension — 7Rear Suspension - Precautions. Preparation — 1Rear Suspension - Noise, Vibration and Harshness (nvh) Troubleshooting (Symptom Diagnosis). Service Data and Specifications (SDS) — 1Rear Suspension - Rear Suspension Assembly — 1Road Wheels & Tires - Precautions — 1Road Wheels & Tires - Preparation. Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Road Wheels & Tires - System — 1Brakes :: Brake System — 9Parking Brake System - Precautions. Preparation — 1Parking Brake System - System — 1Vdc/tcs/abs - Precautions ++ — 1Brake Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Dtc/circuit Diagnosis — 1Brake Control System - Removal and Installation — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Brake Control System - System Description — 1Brake Control System - Basic Inspection — 1Brake Control System - Symptom Diagnosis — 1Steering :: Steering System — 9Steering Control System - Precautions — 1Steering Control System - System — 1Steering Control System - Eps Control Unit (Ecu Diagnosis Information. Removal and Installation) — 1Restraints :: Seat Belt — 7Srs Air Bag - Precautions. Preparation — 1Srs Air Bag - Collision Diagnosis — 1Srs Air Bag - Occupant Classification System — 1Srs Air Bag Control System - Precautions — 1Srs Air Bag Control System - System — 1Srs Air Bag Control System - Diagnosis Sensor Unit — 1Srs Air Bag Control System - Inspection and Adjustment — 1Ventilation, Heater & Air Conditioner :: Ventilation System — 6Heater & Air Conditioning System - Precautions — 1Heater & Air Conditioning System - Preparation — 1Heater & Air Conditioning System - Component Parts — 1Heater & Air Conditioning System - Diagnosis and Repair Work Flow — 1Heater & Air Conditioning System - Compressor — 1Heater & Air Conditioning System - Cooler Pipe and Hose — 1Heater & Air Conditioning System - Condenser. Condenser — 1Heater & Air Conditioning System - Heating and Cooling Unit Assembly — 1Heater & Air Conditioning System - Service Data and Specifications (SDS) — 1Heater & Air Conditioning Control System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1Heater & Air Conditioning Control System - Ecu Diagnosis Information — 1Heater & Air Conditioning Control System - Basic Inspection — 1Heater & Air Conditioning Control System - Dtc/circuit Diagnosis — 1Heater & Air Conditioning Control System - Symptom Diagnosis — 1Heater & Air Conditioning Control System - Removal and Installation — 1Body Interior :: Interior — 8Instrument Panel - Precautions. Preparation. Clip List — 1Instrument Panel - Squeak and Rattle Trouble Diagnoses — 1Instrument Panel - Cluster Lid C — 1Seat - Precautions — 1Seat - Preparation. Clip List — 1Seat - Component Parts — 1Seat - System — 1Seat - Diagnosis and Repair Work Flow — 1Seat - Front Seat — 1Seat - Second Row Seats — 1Seat - Third Row Seats — 1Seat - Front Seat — 1Seat - Second Row Seat — 1Seat - Third Row Seat — 1Automatic Drive Positioner - Precautions. Preparation — 1Automatic Drive Positioner - System — 1Automatic Drive Positioner - Diagnosis and Repair Work Flow — 1Automatic Drive Positioner - Inspection and Adjustment — 1Body Exterior, Doors, Roof & Vehicle Security :: Door & Lock — 38Security Control System - Precautions — 1Security Control System - System — 1Security Control System - Ecm, Bcm, Intelligent Key Unit, Ipdm E/r — 1Security Control System - Vehicle Security System Cannot Be Set — 1Glass & Window System - Precautions. Preparation — 1Glass & Window System - Squeak and Rattle Trouble Diagnoses — 1Power Window Control System - Precautions. Preparation — 1Power Window Control System - Power Supply and Ground Circuit — 1Power Window Control System - Power Window Motor Circuit — 1Power Window Control System - Front Power Window Rh Alone Does Not Operate — 1Power Window Control System - Rear Lh Side Power Window Alone Does Not Operate — 1Power Window Control System - Rear Rh Side Power Window Alone Does Not Operate — 1Roof - Precautions. Preparation — 1Roof - Power Supply and Ground Circuit — 1Roof - Moonroof Switch Assembly — 1Roof - Lin Communication Circuit — 1Roof - Auto Operation Does Not Operate — 1Roof - Anti-Pinch Function Does Not Operate — 1Exterior - Precautions. Preparation. Clip List (Preparation) — 1Exterior - Squeak and Rattle Trouble Diagnoses — 1Exterior - Fender Protector — 1Exterior - Over Fender — 1Exterior - Under Cover — 1Exterior - Roof Side Rail — 1Body Repair - Service Information — 1Service Information - Sheet Metal Work ++ — 1Service Information - Body Welding and Precautions ++ — 1Service Information - Safety and Health ++ — 1Service Information - Repairing Procedures and Precautions ++ — 1Body Repair - Precaution — 1Body Repair - Preparation — 1Body Repair - Removal and Installation — 1Driver Controls :: Mirrors — 8Exterior Lighting System - System Description — 1System Description - Component Parts ++ — 1Exterior Lighting System - Basic Inspection — 1Exterior Lighting System - Dtc/circuit Diagnosis — 1Exterior Lighting System - Symptom Diagnosis — 1Exterior Lighting System - Periodic Maintenance — 1Exterior Lighting System - Removal and Installation — 1Interior Lighting System - Precautions. Preparation — 1Interior Lighting System - Component Parts. Interior Lighting System — 1Interior Lighting System - System — 1Interior Lighting System - Diagnosis and Repair Work Flow — 1Interior Lighting System - Interior Lighting System Symptoms (Symptom Diagnosis). Bcm (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Interior Lighting System - Foot Lamp — 1Wiper & Washer - Precautions — 1Wiper & Washer - Preparation. Bcm, Ipdm E/r (Ecu Diagnosis Information). Service Data and Specifications (SDS) — 1Wiper & Washer - System — 1Wiper & Washer - Diagnosis and Repair Work Flow — 1Defogger - Precautions. Bcm, A/c Auto Amp. (Ecu Diagnosis Information) — 1Defogger - Diagnosis and Repair Work Flow — 1Horn - Precautions — 1Electrical & Power Control :: Power Outlet — 13Body Control System - Precautions. Preparation — 1Body Control System - Component Parts — 1Body Control System - System — 1Body Control System - Diagnosis System (bcm) — 1Body Control System - Bcm — 1Lan System - System Description — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Lan System - System Description — 1Lan System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - System Description — 1Power Control System - Basic Inspection — 1Power Control System - Dtc/circuit Diagnosis — 1Power Control System - Removal and Installation — 1Charging System - Precautions. Preparation. Ecm, Ipdm E/r (Ecu Diagnosis Information) — 1Charging System - Diagnosis and Repair Work Flow — 1Charging System - Charging System (Symptom Diagnosis). Generator (Removal and Installation). Service Data and Specifications (SDS) — 1Power Supply, Ground & Circuit Elements - Precautions. Preparation. Service Data and Specifications (SDS) — 1Driver Information & Multimedia :: Meter, Warning Lamp & Indicator — 25Warning Chime System - Application Notice (How to Use This Manual). Precautions — 1Warning Chime System - System — 1Warning Chime System - Diagnosis System (combination Meter) — 1Warning Chime System - Bcm, Combination Meter (Ecu Diagnosis Information). Diagnosis and Repair Work Flow (Basic Inspection) — 1Sonar System - Precautions. Preparation — 1Sonar System - Sonar Control Unit — 1Dtc/circuit Diagnosis - B2720 Corner Sensor [rl] ++ — 1Audio, Visual & Navigation System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Multi Av (av Control Unit) ++ — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Symptom Diagnosis - Multi Av System ++ — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Ecu Diagnosis Information — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Audio, Visual & Navigation System - System Description — 1Audio, Visual & Navigation System - Basic Inspection — 1Audio, Visual & Navigation System - Dtc/circuit Diagnosis — 1Audio, Visual & Navigation System - Symptom Diagnosis — 1Audio, Visual & Navigation System - Removal and Installation — 1Cruise Control & Driver Assistance :: Cruise Control System — 17Driver Assistance System - System Description — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Driver Assistance System - System Description — 1System Description - Component Parts ++ — 1System Description - System ++ — 1System Description - Operation ++ — 1System Description - Handling Precaution ++ — 1Driver Assistance System - Ecu Diagnosis Information — 1Driver Assistance System - Basic Inspection — 1Basic Inspection - Distance Sensor Alignment ++ — 1Basic Inspection - Camera Aiming Adjustment ++ — 1Basic Inspection - Action Test ++ — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Dtc/circuit Diagnosis - Laser/radar (distance Sensor) ++ — 1Dtc/circuit Diagnosis - Lane Camera (front Camera Unit) ++ — 1Driver Assistance System - Symptom Diagnosis — 1Driver Assistance System - Removal and Installation — 1Driver Assistance System - System Description — 1System Description - System ++ — 1Driver Assistance System - Basic Inspection — 1Driver Assistance System - Dtc/circuit Diagnosis — 1Drive Mode System - Precautions — 1Drive Mode System - Component Parts. Drive Mode System — 1Drive Mode System - System — 1Drive Mode System - Diagnosis and Repair Work Flow — 1Drive Mode System - Drive Mode Select Switch Circuit — 1Maintenance - Precautions. Preparation — 1Maintenance - General Maintenance — 1Maintenance - Periodic Maintenance — 1Maintenance - Recommended Fluids and Lubricants — 1Maintenance - Engine Maintenance — 1Maintenance - Chassis and Body Maintenance — 1Engine Lubrication System - Periodic Maintenance — 1Engine Lubrication System - Removal and Installation — 1Engine Cooling System - System Description — 1Engine Cooling System - Removal and Installation — 1Engine Control System - Vq35dd — 1Fuel System - Removal and Installation — 1Starting System - System Description — 1Starting System - Dtc/circuit Diagnosis — 1Driveline - Transfer: Ty92b — 1Driveline - Rear Propeller Shaft: 3fcj-Cvj — 1Driveline - Rear Final Drive: R145 — 1Front Axle - Periodic Maintenance — 1Front Axle - Removal and Installation — 1Rear Axle - Periodic Maintenance — 1Rear Axle - Removal and Installation — 1Rear Suspension - Removal and Installation — 1Road Wheels & Tires - System Description — 1Road Wheels & Tires - Basic Inspection — 1Road Wheels & Tires - Dtc/circuit Diagnosis — 1Road Wheels & Tires - Symptom Diagnosis — 1Road Wheels & Tires - Periodic Maintenance — 1Road Wheels & Tires - Removal and Installation — 1Parking Brake System - System Description — 1Parking Brake System - Basic Inspection — 1Parking Brake System - Dtc/circuit Diagnosis — 1Parking Brake System - Symptom Diagnosis — 1Parking Brake System - Removal and Installation — 1Brake Control System - Vdc/tcs/abs — 1Brake Control System - Automatic Brake Hold — 1Brake Control System - Automatic Emergency Braking — 1Brake Control System - Rear Automatic Braking — 1Steering Control System - System Description — 1Steering Control System - Basic Inspection — 1Steering Control System - Dtc/circuit Diagnosis — 1Steering Control System - Symptom Diagnosis — 1Srs Air Bag - Removal and Installation — 1Srs Air Bag Control System - System Description — 1Srs Air Bag Control System - Basic Inspection — 1Srs Air Bag Control System - Symptom Diagnosis — 1Heater & Air Conditioning System - Symptom Diagnosis — 1Heater & Air Conditioning System - Periodic Maintenance — 1Heater & Air Conditioning Control System - Automatic Air Conditioning — 1Instrument Panel - Removal and Installation — 1Instrument Panel - Unit Disassembly and Assembly — 1Seat - Ecu Diagnosis Information — 1Seat - Dtc/circuit Diagnosis — 1Seat - Symptom Diagnosis — 1Automatic Drive Positioner - System Description — 1Automatic Drive Positioner - Ecu Diagnosis Information — 1Automatic Drive Positioner - Dtc/circuit Diagnosis — 1Automatic Drive Positioner - Symptom Diagnosis — 1Automatic Drive Positioner - Removal and Installation — 1Security Control System - System Description — 1Security Control System - Basic Inspection — 1Security Control System - Dtc/circuit Diagnosis — 1Security Control System - Symptom Diagnosis — 1Security Control System - Removal and Installation — 1Glass & Window System - Removal and Installation — 1Power Window Control System - System Description — 1Power Window Control System - Ecu Diagnosis Information — 1Power Window Control System - Basic Inspection — 1Power Window Control System - Dtc/circuit Diagnosis — 1Power Window Control System - Symptom Diagnosis — 1Power Window Control System - Removal and Installation — 1Roof - System Description — 1Roof - Ecu Diagnosis Information — 1Roof - Basic Inspection — 1Roof - Dtc/circuit Diagnosis — 1Roof - Symptom Diagnosis — 1Roof - Removal and Installation — 1Exterior - System Description — 1Exterior - Removal and Installation — 1Body Repair - Repair Information — 1Exterior Lighting System - Led Headlamp — 1Interior Lighting System - Dtc/circuit Diagnosis — 1Interior Lighting System - Removal and Installation — 1Wiper & Washer - System Description — 1Wiper & Washer - Dtc/circuit Diagnosis — 1Wiper & Washer - Symptom Diagnosis — 1Wiper & Washer - Removal and Installation — 1Defogger - System Description — 1Defogger - Dtc/circuit Diagnosis — 1Defogger - Symptom Diagnosis — 1Defogger - Removal and Installation — 1Horn - Removal and Installation — 1Body Control System - Basic Inspection — 1Body Control System - Dtc/circuit Diagnosis — 1Body Control System - Symptom Diagnosis — 1Body Control System - Removal and Installation — 1Lan System - Can Fundamental — 1Lan System - Can — 1Lan System - Can Gateway — 1Power Control System - Ipdm E/r — 1Power Control System - Power Distribution System — 1Charging System - System Description — 1Charging System - Dtc/circuit Diagnosis — 1Power Supply, Ground & Circuit Elements - System Description — 1Power Supply, Ground & Circuit Elements - Basic Inspection — 1Power Supply, Ground & Circuit Elements - Removal and Installation — 1Warning Chime System - System Description — 1Warning Chime System - Dtc/circuit Diagnosis — 1Warning Chime System - Symptom Diagnosis — 1Sonar System - System Description — 1Sonar System - Basic Inspection — 1Sonar System - Dtc/circuit Diagnosis — 1Sonar System - Symptom Diagnosis — 1Sonar System - Removal and Installation — 1Audio, Visual & Navigation System - Nissanconnect — 1Audio, Visual & Navigation System - Intelligent Around View Monitor System — 1Audio, Visual & Navigation System - Rear View Monitor System — 1Audio, Visual & Navigation System - Telematics System — 1Driver Assistance System - Adas Control Unit 2 — 1Driver Assistance System - Driver Assistance System — 1Driver Assistance System - Chassis Control — 1Drive Mode System - Removal and Installation — 1Dtc/circuit Diagnosis (C053c Wheel Speed Sensor ... U2141 Can Comm Circuit) — 1Dtc/circuit Diagnosis (P0011 Intake Valve Timing Control ... P0111 Iat Sensor) — 1Dtc/circuit Diagnosis (P0116 Engine Coolant Temperature Sensor ... P025b Fuel Pump Module a) — 1Dtc/circuit Diagnosis (P026b Injection Timing ... P0420 Three Way Catalyst Function) — 1Dtc/circuit Diagnosis (P0441 Evap Control System ... P0524 Engine Oil Pressure) — 1Dtc/circuit Diagnosis (P0532 A/c Refrigerant Pressure Sensor ... P064d Ecm) — 1Dtc/circuit Diagnosis (P06da Engine Oil Pressure Control Solenoid Valve ... P1217 Engine Over Temperature) — 1Dtc/circuit Diagnosis (P1220 Fuel Pump Control Module (fpcm) ... P1574 Ascd Vehicle Speed Sensor) — 1Dtc/circuit Diagnosis (P1575 Brake Switch ... P2101 Electric Throttle Control Function) — 1Dtc/circuit Diagnosis (P2118 Throttle Control Motor ... P34ac Electric Intake Valve Timing Control Actuator) — 1Dtc/circuit Diagnosis (Active Grille Shutter ... High Pressure Fuel Pump) — 1Dtc/circuit Diagnosis (Ignition Signal ... Variable Induction Air System) — 14012 C1040 Emergency Brake — 14013 C106a Wheel Sensor — 14014 C1078-55 Not Configuration — 14015 C10b4-98 Overheat — 14016 B1001 Lap Pre-Tensioner Lh — 14017 B0001 Driver Air Bag Module — 14018 B100e Knee Air Bag Module Rh — 14019 B142x Collision Detection — 1Dtc/circuit Diagnosis (B20c7-11 A/c Clutch ... B24a6-11 in-Vehicle Sensor) — 1Dtc/circuit Diagnosis (B24a6-15 in-Vehicle Sensor ... U2140-87 Can Comm Err (ecm)) — 1Dtc/circuit Diagnosis (C1f00-1c Control Unit ... C1f04-61 Brake Sw/stop Lamp Sw) — 1Dtc/circuit Diagnosis (C1f05-49 Front Camera Unit ... C1f70-87 Ethernet Circuit) — 1
230steps
~1380min
5/5difficulty
Done 0 of 230
  • P026b Injection Timing
  • P0300 Misfire
  • P0315 Crankshaft Position
  • P0326 Knock Sensor
  • P0327 Ks
  • P0335 Crankshaft Position Sensor
  • P0340 Cmp Sensor
  • P0365 Exhaust Camshaft Position Sensor
  • P0385 Ckp Sensor 2
  • P0420 Three Way Catalyst Function

P026b Injection Timing Nissan Pathfinder 2022

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P026B 00 Injection timing Diagnosis condition —
Signal —
Threshold ECM does not control fuel injection timing properly when engine is running (except engine cold start).
Diagnosis delay time 1 second

POSSIBLE CAUSE

ECM

FAIL-SAFE

Not applicable

Confirmation Procedure

PERFORM DTC CONFIRMATION PROCEDURE

Start engine and drive the Nissan Pathfinder vehicle as per the similar conditions to Freeze Frame Data for 5 seconds.

Hold the accelerator pedal as steady as possible.

  • COOLANT TEMP

  • ENGINE SPEED

  • CAL/LD VALUE

Is DTC detected?

YES>>

Proceed to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

REPLACE ECM

  1. Replace ECM. Refer to Removal and Installation.

  2. Refer to Work Procedure.

>>

INSPECTION END

P0300 Misfire Nissan Pathfinder SUV

DTC Description

When a misfire occurs, engine speed will fluctuate. If the engine speed fluctuates enough to cause the crankshaft position (CKP) sensor 1 (POS) signal to vary, ECM can determine that a misfire is occurring.

Sensor Input signal to ECM ECM function
Crankshaft position sensor 1 (POS) Engine speed On board diagnosis of misfire

The misfire detection logic consists of the following two conditions.

  1. One Trip Detection Logic (Three Way Catalyst Damage)

    On the 1st trip, when a misfire condition occurs that can damage the three way catalyst (TWC) due to overheating, the MIL will blink.

    When a misfire condition occurs, the ECM monitors the CKP sensor 1 signal every 200 engine revolutions for a change.

    When the misfire condition decreases to a level that will not damage the TWC, the MIL will turn off.

    If another misfire condition occurs that can damage the TWC on a second trip, the MIL will blink.

    When the misfire condition decreases to a level that will not damage the TWC, the MIL will remain illuminating.

    If another misfire condition occurs that can damage the TWC, the MIL will begin to blink again.

  2. Two Trip Detection Logic (Exhaust quality deterioration)

    For misfire conditions that will not damage the TWC (but will affect Nissan Pathfinder vehicle emissions), the MIL will only illuminate when the misfire is detected on a second trip. During this condition, the ECM monitors the CKP sensor 1 signal every 1,000 engine revolutions.

    A misfire malfunction can be detected in any one cylinder or in multiple cylinders.

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0300 00

MULTI CYL MISFIRE

(Random/Multiple cylinder misfire detected)
Diagnosis condition —
Signal (terminal) —
Threshold Multiple cylinders misfire
Diagnosis delay time —

POSSIBLE CAUSE

  • Improper spark plug

  • Insufficient compression

  • Incorrect fuel pressure

  • The fuel injector circuit is open or shorted

  • Fuel injector

  • Intake air leak

  • The ignition signal circuit is open or shorted

  • Lack of fuel

  • Signal plate

  • A/F sensor 1

  • Incorrect PCV hose connection

FAIL-SAFE

Fail safe mode Nissan Pathfinder Vehicle behavior
Traveling control mode Accelerator angle variation control

ECM controls the accelerator pedal depression speed to make it slower than actual speed. This causes a drop in accelerating performance and encourages the driver to repair malfunction.

Combustion control mode Stratified charge combustion control at starting No stratified charge combustion at starting (cold start).
Idle speed control Stops feedback control of idle speed and controls with specified speed.
Recovery speed control at decelerating Stops recovery speed control by the fuel cut at decelerating and controls with specified speed.
Idle neutral control Stops idle neutral control.

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE-I

  1. Start engine and warm it up to normal operating temperature.

  2. Turn ignition switch OFF and wait at least 10 seconds.

  3. Turn ignition switch ON.

  4. Turn ignition switch OFF and wait at least 10 seconds.

  5. Restart engine and let it idle for about 15 minutes.

  6. Check 1st trip DTC.

Is DTC P0300 detected?

YES>>

Proceed to Diagnosis Procedure.

NO>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE-II

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

  4. Start engine and drive the Nissan Pathfinder vehicle under similar conditions to (1st trip) Freeze Frame Data for a certain time. Refer to the table below.

    Hold the accelerator pedal as steady as possible.

    Similar conditions to (1st trip) Freeze Frame Data mean that the following conditions should be satisfied at the same time.

    Engine speed Engine speed in the freeze frame data ± 400 rpm
    Nissan Pathfinder Vehicle speed Vehicle speed in the freeze frame data ± 10 km/h
    Base fuel schedule Base fuel schedule in the freeze frame data × (1 ± 0.1)
    Engine coolant temperature (T) condition

    When the freeze frame data shows lower than 70 °C,

    T should be lower than 70 °C.

    When the freeze frame data shows higher than or equal to 70 °C,

    T should be higher than or equal to 70 °C.

    Driving time varies according to the engine speed in the freeze frame data.

    Engine speed Time
    Around 1,000 rpm Approximately 10 minutes
    Around 2,000 rpm Approximately 5 minutes
    More than 3,000 rpm Approximately 3.5 minutes
  5. Check 1st trip DTC.

Is DTC P0300 detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK GROUND CONNECTION

Check the following.

  • Connection condition of the ground F59 and F60

  • Connection condition of the ground harness between engine assembly and Nissan Pathfinder vehicle body (If equipped)

Is the inspection result normal?

YES>>

GO TO 2

NO>>

Repair or replace error-detected parts.

CHECK FOR INTAKE AIR LEAK AND PCV HOSE

  1. Start engine and run it at idle speed.

  2. Listen for the sound of the intake air leak.

  3. Check PCV hose connection.

Is intake air leak detected?

YES>>

Discover air leak location and repair.

NO>>

GO TO 3.

CHECK FOR EXHAUST SYSTEM CLOGGING

Stop engine and visually check exhaust tube, three way catalyst and muffler for dents.

Is the inspection result normal?

YES-1>>

With CONSULT: GO TO 4.

YES-2>>

Without CONSULT: GO TO 5.

NO>>

Repair or replace it.

PERFORM POWER BALANCE TEST

With CONSULT

  1. Start engine.

  2. Perform “POWER BALANCE” in “Active Test” mode of “ENGINE”.

  3. Make sure that each circuit produces a momentary engine speed drop.

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

GO TO 5.

CHECK FUNCTION OF FUEL INJECTOR

  1. Start engine and let it idle.

  2. Listen to each fuel injector operation sound.

    Clicking sound should be heard.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Perform trouble diagnosis for FUEL INJECTOR, refer to Diagnosis Procedure.

CHECK FUNCTION OF IGNITION COIL-I

  1. Turn ignition switch OFF.

  2. Pull out 20A fuse (No.85) from IPDM E/R to release fuel pressure. Refer to IPDM E/R Terminal Arrangement .

  3. Start engine.

  4. After engine stalls, crank it two or three times to release all fuel pressure.

  5. Turn ignition switch OFF.

  6. Remove all ignition coil harness connectors to avoid the electrical discharge from the ignition coils.

  7. Remove ignition coil and spark plug of the cylinder to be checked.

  8. Crank engine for 5 seconds or more to remove combustion gas in the cylinder.

  9. Connect spark plug and harness connector to ignition coil.

  10. Fix ignition coil using a rope etc. with gap of 13 – 17 mm (0.52 – 0.66 in) between the edge of the spark plug and grounded metal portion as shown in the figure.

  11. Crank engine for about 3 seconds, and check whether spark is generated between the spark plug and the grounded metal portion.

    Spark should be generated.

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

GO TO 7.

CHECK FUNCTION OF IGNITION COIL-II

  1. Turn ignition switch OFF.

  2. Disconnect spark plug and connect a non-malfunctioning spark plug.

  3. Crank engine for about 3 seconds, and recheck whether spark is generated between the spark plug and the grounded metal portion.

    Spark should be generated.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Check ignition coil, power transistor and their circuits. Refer to Diagnosis Procedure.

CHECK SPARK PLUG

Check the initial spark plug for fouling, etc.

Is the inspection result normal?

YES>>

Replace spark plug(s) with standard type one(s). For spark plug type, refer to Exploded View.

NO>>

Repair or clean spark plug. Then GO TO 9.

CHECK FUNCTION OF IGNITION COIL-III

  1. Reconnect the initial spark plugs.

  2. Crank engine for about 3 seconds, and recheck whether spark is generated between the spark plug and the grounded portion.

    Spark should be generated.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace spark plug(s) with standard type one(s). For spark plug type, refer to Exploded View.

CHECK COMPRESSION PRESSURE

Check compression pressure. Refer to Exploded View.

Is the inspection result normal?

YES>>

GO TO 11.

NO>>

Check pistons, piston rings, valves, valve seats and cylinder head gaskets.

CHECK FUEL PRESSURE

  1. Install all removed parts.

  2. Release fuel pressure to zero. Refer to Work Procedure.

  3. Install fuel pressure gauge and check fuel pressure. Refer to Work Procedure.

Is the inspection result normal?

YES>>

GO TO 13.

NO>>

GO TO 12.

DETECT MALFUNCTIONING PART

Check fuel hoses and fuel tubes for clogging.

Is the inspection result normal?

YES>>

Replace “fuel filter and fuel pump assembly”.

NO>>

Repair or replace.

CHECK IDLE SPEED AND IGNITION TIMING

For procedure, refer to Work Procedure.

For specification, refer to Idle Speed and Ignition Timing.

Is the inspection result normal?

YES>>

GO TO 14.

NO>>

Follow the Work Procedure.

CHECK A/F SENSOR 1 INPUT SIGNAL CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect corresponding A/F sensor 1 harness connector.

  3. Disconnect ECM harness connector.

  4. Check the continuity between A/F sensor 1 harness connector and ECM harness connector.

    Bank A/F sensor 1 ECM Continuity
    Connector Terminal Connector Terminal
    1 F72 3 F79 102 Existed
    4 101
    2 F73 3 106
    4 105
  5. Check the continuity between A/F sensor 1 harness connector and ground, or ECM harness connector and ground.

    Bank A/F sensor 1 — Continuity
    Connector Terminal
    1 F72 3 Ground Existed
    4
    2 F73 3
    4
    Bank ECM — Continuity
    Connector Terminal
    1 F79 101 Ground Existed
    102
    2 105
    106
  6. Also check harness for short to power.

Is the inspection result normal?

YES>>

GO TO 15.

NO>>

Repair open circuit, short to ground or short to power in harness or connectors.

CHECK A/F SENSOR 1 HEATER

Refer to Component Inspection (A/F Sensor 1 Heater).

Is the inspection result normal?

YES>>

GO TO 16.

NO>>

Replace (malfunctioning) A/F sensor 1. Refer to Exploded View.

CHECK MASS AIR FLOW SENSOR

With CONSULT

Check “MASS AIR FLOW SENSOR (Hz)” in “Data Monitor” mode of “ENGINE”.

For specification, refer to Component Inspection (Mass Air Flow Sensor).

With GST

Check mass air flow sensor signal in Service $01 with GST.

For specification, refer to Mass Air Flow Sensor.

Is the measurement value within the specification?

YES>>

GO TO 17.

NO>>

Check connectors for rusted terminals or loose connections in the mass air flow sensor circuit or ground. Refer to Diagnosis Procedure.

CHECK SYMPTOM TABLE

Check items on the rough idle symptom in Symptom Table.

Is the inspection result normal?

YES>>

GO TO 18.

NO>>

Repair or replace.

ERASE THE 1ST TRIP DTC

Some tests may cause a 1st trip DTC to be set.

Erase the 1st trip DTC from the ECM memory after performing the tests. Refer to CONSULT Function (With CONSULT).

>>

INSPECTION END

P0315 Crankshaft Position Nissan Pathfinder

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0315 00

Crankshaft position

(Crankshaft Position System Variation Not Learned)
Diagnosis condition Engine run and fuel shut off
Signal —
Threshold Learning value of signal plate variation is abnormal or not learned.
Diagnosis delay time —

POSSIBLE CAUSE

  • Signal plate

  • Crankshaft position sensor 1

  • Harness or connectors (Crankshaft position sensor 1 circuit is open or shorted.)

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

CHECK DTC PRIORITY

If DTC P0315 is displayed with DTC P0335, first perform the trouble diagnosis for DTC P0335.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Description.

NO>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start the engine and warm it up to normal operating temperature.

  2. Drive Nissan Pathfinder vehicle at 80 km/h, with selecting suitable gear.

  3. Release accelerator pedal completely to decelerate the Nissan Pathfinder vehicle.

  4. Repeat the step 2 and 3 until the integrated deceleration time to be 30 seconds.

  5. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Proceed to DIAGNOSIS PROCEDURE.

NO-1>>

To check malfunction symptom before repair: Refer to Diagnosis Procedure.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P0315 is displayed with DTC P0335, first perform the trouble diagnosis for DTC P0335.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Description.

NO>>

GO TO 2.

CHECK GEAR TOOTH

Visually check for chipping signal plate gear tooth.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace the signal plate. Refer to Exploded View.

P0326 Knock Sensor Nissan Pathfinder SUV

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detected condition
P0326 00

KNOCK SENSOR 1 B1

(Knock/Combustion Vibration Sensor 1 Circuit Range/Performance Bank 1 or Single Sensor)
Diagnosis condition During fuel cut after engine warm-up
Signal Knock sensor
Threshold When the ECM detects knocking during engine running more than the threshold value
Diagnosis delay time 5 seconds

POSSIBLE CAUSE

Harness or connectors

(The knock sensor circuit is open or shorted.)

  • Knock sensor

  • Knock sensor installation

FAIL SAFE

Not applicable

DTC Confirmation Procedure

DTC CONFIRMATION PROCEDURE

CHECK DTC PRIORITY

If DTC P0326 is displayed with DTC P0327 or P0328, first perform the confirmation procedure (trouble diagnosis) for DTC P0327 or P0328.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Index.

NO>>

GO TO 2.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 10 V or more at idle.

>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and warm it up to normal operating temperature.

  2. Revving engine from idle up to 3,000 rpm quickly.

  3. Repeat the step 2 at 10 times.

  4. Check DTC.

Is DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P0326 is displayed with DTC P0327 or P0328, first perform the confirmation procedure (trouble diagnosis) for DTC P0327 or P0328.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable. Refer to Diagnosis Procedure.

NO>>

GO TO 2.

CHECK INSTALLATION CONDITION OF KNOCK SENSOR

Visually check that the knock sensor is installed normally.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace error-detected parts.

CHECK INTERMITTENT INCIDENT

Check intermittent incident. Refer to Intermittent Incident.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts.

CHECK KNOCK SENSOR CIRCUIT

Check knock sensor circuit. Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace error-detected parts.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON.

  2. Erase DTC.

  3. Perform DTC confirmation procedure. Refer to DTC Confirmation Procedure.

Is the 1st trip DTC P0326 displayed again?

YES>>

Replace ECM. Refer to Removal and Installation .

NO>>

INSPECTION END

P0327 Ks Nissan Pathfinder R53

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0327 00

KNOCK SEN/CIRC-B1

(Knock sensor 1 circuit low bank 1)
Diagnosis condition Engine running at idle
Signal (terminal) Knock sensor (bank 1) signal
Threshold An excessively low voltage from the sensor is sent to ECM
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors [The knock sensor (bank 1) circuit is open or shorted.]

  • Knock sensor (bank 1)

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 10 V at idle.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and run it for at least 5 seconds at idle speed.

  2. Check 1st trip DTC.

Is DTC P0327 detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK KNOCK SENSOR GROUND CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect knock sensor harness connector and ECM harness connector.

  3. Check the continuity between knock sensor harness connector and ECM harness connector.

    Knock sensorECMContinuity
    BankConnectorTerminalConnectorTerminal
    1 F211 2 F78 8 Existed
  4. Also check harness for short to power.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace error-detected parts.

CHECK ECM GROUND CIRCUIT

  1. Check the continuity between ECM harness connector and ground.

    ECM—Continuity
    ConnectorTerminal
    F78 3 Ground Existed
    F79 87
    E32 199
    201
    204
  2. Also check harness for short to power.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace error-detected parts.

CHECK KNOCK SENSOR INPUT SIGNAL CIRCUIT

  1. Check the continuity between knock sensor harness connector and ECM harness connector.

    Knock sensorECMContinuity
    BankConnectorTerminalConnectorTerminal
    1 F211 1 F78 7 Existed
  2. Also check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts.

CHECK KNOCK SENSOR

Refer to Component Inspection.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace malfunctioning knock sensor. Refer to Exploded View.

Component Inspection

CHECK KNOCK SENSOR

  1. Turn ignition switch OFF.

  2. Disconnect knock sensor harness connector.

  3. Check resistance between knock sensor terminals as per the following.

Knock sensorConditionResistance
Terminal
1 2 Temperature [°C (°F)] 20 (68) 532 – 588 kΩ

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace malfunctioning knock sensor. Refer to Exploded View.

P0335 Crankshaft Position Sensor Nissan Pathfinder 2022

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0335 00

CKP SEN/CIRCUIT

(Crankshaft position sensor “A” circuit)
Diagnosis condition
  • Engine: Cranking or running

  • Camshaft position sensor signal is inputted

Signal (terminal) Crankshaft position sensor 1 signal
Threshold
  • Crankshaft position sensor 1 signal is not input to ECM

  • Crankshaft position sensor 1 signal is inappropriate or partly missing

Diagnosis delay time 1 second or more

POSSIBLE CAUSE

  • Harness or connectors

    (Crankshaft position sensor 1 circuit is open or shorted.)

  • Crankshaft position sensor 1

  • Signal plate (drive plate)

FAIL-SAFE

Fail safe mode Nissan Pathfinder Vehicle behavior
Device fix mode
  • Fixes electric intake valve timing control motor in the reference position.

  • Fixes exhaust valve timing control solenoid valve in the reference position.

Combustion control mode Stratified charge combustion control at starting No stratified charge combustion at starting (cold start).
Idle speed control Stops feedback control of idle speed and controls with specified speed.
Recovery speed control at decelerating Stops recovery speed control by the fuel cut at decelerating and controls with specified speed.
Idle neutral control Stops idle neutral control.

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON.

  2. Shift the selector lever in N range.

  3. Start the engine and let it idle at least 5 seconds.

  4. Check DTC.

Is DTC P0335 detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK HARNESS CONNECTOR

  1. Turn ignition switch OFF.

  2. Disconnect crankshaft position (CKP) sensor 1 harness connectors.

  3. Reconnect crankshaft position (CKP) sensor 1 harness connectors.

  4. Perform DTC confirmation procedure.

Is DTC detected?

YES>>

GO TO 2.

NO>>

INSPECTION END

CHECK GROUND CONNECTION

Check ground connection.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace ground connection.

CHECK CRANKSHAFT POSITION (CKP) SENSOR 1 POWER SUPPLY

  1. Turn ignition switch OFF.

  2. Disconnect crankshaft position sensor 1 harness connector.

  3. Turn ignition switch ON.

  4. Check the voltage between CKP sensor 1 harness connector and ground.

    + −

    Voltage

    (Approx.)
    CKP sensor 1
    Connector Terminal
    F11 1 Ground 5 V

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

GO TO 4.

CHECK CKP SENSOR 1 POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF

  2. Disconnect ECM harness connector.

  3. Check the continuity between CKP sensor 1 harness connector and ECM harness connector.

    CKP sensor 1 ECM Continuity
    Connector Terminal Connector Terminal
    F11 1 F78 39 Existed
  4. Also check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

Perform the trouble diagnosis for ECM power supply circuit.

NO>>

Repair or replace error-detected parts.

CHECK CKP SENSOR 1 GROUND CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between CKP sensor 1 harness connector and ECM harness connector.

    CKP sensor 1 ECM Continuity
    Connector Terminal Connector Terminal
    F11 2 F78 22 Existed
  4. Also check harness for short to power.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace error-detected parts.

CHECK CKP SENSOR 1 INPUT SIGNAL CIRCUIT

  1. Check the continuity between CKP sensor 1 harness connector and ECM harness connector.

    CKP sensor 1 ECM Continuity
    Connector Terminal Connector Terminal
    F11 3 F78 31 Existed
  2. Also check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair or replace error-detected parts.

CHECK CKP SENSOR 1

Check CKP sensor 1. Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Replace CKP sensor 1. Refer to Exploded View.

CHECK GEAR TOOTH

  1. Remove CKP sensor 1. Refer to Exploded View.

  2. Look into the mounting hole of the CKP sensor 1 to check that there is no missing gear tooth in the signal plate .

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace the signal plate (drive plate). Refer to Exploded View.

Component Inspection

CHECK CRANKSHAFT POSITION (CKP) SENSOR 1-I

  1. Turn ignition switch OFF.

  2. Loosen the fixing bolt of the sensor.

  3. Disconnect CKP sensor 1 harness connector.

  4. Remove the sensor.

  5. Visually check the sensor for chipping.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace CKP sensor 1. Refer to Exploded View.

CHECK CKP SENSOR-II

Check the resistance between CKP sensor terminals as per the following.

CKP sensor 1 Condition Resistance
Terminal (Polarity)
1 2 Temperature [°C (°F)] 25 (77) Except 0 or ∞Ω
3
2 3

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace CKP sensor 1. Refer to Exploded View.

P0340 Cmp Sensor Nissan Pathfinder

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0340 00

CMP SEN/CIRC-B1

(Camshaft position sensor “A” circuit bank 1)
Diagnosis condition Engine: Cranking or running (idle speed or more than 800 rpm)
Signal (terminal) Intake camshaft position sensor (PHASE) (bank 1) signal
Threshold
  • The cylinder No. signal is not sent to ECM for the first few seconds during engine cranking

  • The cylinder No. signal is not sent to ECM during engine running

  • The cylinder No. signal is not in the normal pattern during engine running

Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors [Intake camshaft position sensor (bank 1) circuit is open or shorted.]

  • Intake camshaft position sensor (bank 1)

  • Camshaft (INT)

  • Starter motor

  • Starting system circuit

  • Dead (Weak) battery

FAIL-SAFE

Fail safe mode Nissan Pathfinder Vehicle behavior
Device fix mode
  • Fixes electric intake valve timing control motor in the reference position.

  • Fixes exhaust valve timing control solenoid valve in the reference position.

Combustion control mode Stratified charge combustion control at starting No stratified charge combustion at starting (cold start).
Idle speed control Stops feedback control of idle speed and controls with specified speed.
Recovery speed control at decelerating Stops recovery speed control by the fuel cut at decelerating and controls with specified speed.
Idle neutral control Stops idle neutral control.

DTC Confirmation Procedure

CHECK DTC PRIORITY

If DTC P0340 is displayed with DTC P0643, first perform the confirmation procedure (trouble diagnosis) for DTC P0643.

Is DTC P0643 detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Description.

NO>>

GO TO 2.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 10.5 V with ignition switch ON.

>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE-I

  1. Start engine and let it idle for at least 5 seconds.

    If engine does not start, crank engine for at least 2 seconds.

  2. Check 1st trip DTC.

Is DTC P0340 detected?

YES>>

Proceed to Diagnosis Procedure.

NO>>

GO TO 4.

PERFORM DTC CONFIRMATION PROCEDURE-II

  1. Maintaining engine speed at more than 800 rpm for at least 5 seconds.

  2. Check 1st trip DTC.

Is DTC P0340 detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P0340 is displayed with DTC P0643, first perform the confirmation procedure (trouble diagnosis) for DTC P0643.

Is DTC P0643 detected?

YES>>

Perform diagnosis of applicable. Refer to DTC Description.

NO>>

GO TO 2.

CHECK STARTING SYSTEM

Turn ignition switch to START position.

Does the engine turn over? Does the starter motor operate?

YES>>

GO TO 3.

NO>>

Check starting system. (Refer to Work Flow (With 165–DSS-5000P) or Work Flow (Without 165–DSS-5000P). For details, Refer to Special Service Tool.)

CHECK GROUND CONNECTION

  1. Turn ignition switch OFF.

  2. Check ground connection E9. Refer to Ground Inspection in Circuit Inspection.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace ground connection.

CHECK INTAKE CAMSHAFT POSITION SENSOR POWER SUPPLY

  1. Disconnect intake camshaft position sensor harness connector.

  2. Turn ignition switch ON.

  3. Check the voltage between intake camshaft position sensor harness connector and ground.

    + −

    Voltage

    (Approx.)
    Intake camshaft position sensor
    Bank Connector Terminal
    1 F113 1 Ground 5 V

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

GO TO 5.

CHECK INTAKE CAMSHAFT POSITION SENSOR POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between intake camshaft position sensor harness connector and ECM harness connector.

    Intake camshaft position sensor ECM Continuity
    Bank Connector Terminal Connector Terminal
    1 F113 1 F78 40 Existed
  4. Also check harness for short to power and short to ground.

Is the inspection result normal?

YES-1>>

P0340: Perform the trouble diagnosis for ECM power supply circuit. Refer to Diagnosis Procedure.

YES-2>>

P0345: GO TO 6.

NO>>

Repair or replace error-detected parts.

CHECK SENSOR POWER SUPPLY 2 CIRCUIT

Refer to Diagnosis Procedure.

Is the inspection result normal?

YES>>

Perform the trouble diagnosis for ECM power supply circuit. Refer to Diagnosis Procedure.

NO>>

Repair or replace error-detected parts.

CHECK INTAKE CAMSHAFT POSITION SENSOR GROUND CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between intake camshaft position sensor harness connector and ECM harness connector.

    Intake camshaft position sensor ECM Continuity
    Bank Connector Terminal Connector Terminal
    1 F113 2 F78 27 Existed
  4. Also check harness for short to power.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair or replace error-detected parts.

CHECK INTAKE CAMSHAFT POSITION SENSOR INPUT SIGNAL CIRCUIT

  1. Check the continuity between intake camshaft position sensor harness connector and ECM harness connector.

    Intake camshaft position sensor ECM Continuity
    Bank Connector Terminal Connector Terminal
    1 F113 3 F78 36 Existed
  2. Also check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Repair or replace error-detected parts.

CHECK INTAKE CAMSHAFT POSITION SENSOR

Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Replace malfunctioning intake camshaft position sensor. Refer to Exploded View.

CHECK CAMSHAFT (INTAKE)

Check the following.

  • Accumulation of debris to the signal plate of camshaft rear end

  • Chipping signal plate of camshaft rear end

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Remove debris and clean the signal plate of camshaft rear end or replace camshaft. Refer to Removal and Installation.

Component Inspection

CHECK INTAKE CAMSHAFT POSITION (CMP) SENSOR-I

  1. Turn ignition switch OFF.

  2. Disconnect intake CMP sensor harness connector.

  3. Remove the sensor. Refer to Exploded View.

  4. Visually check the sensor for chipping.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace the malfunctioning intake CMP sensor. Refer to Exploded View.

CHECK INTAKE CMP SENSOR-II

Check resistance intake CMP sensor terminals as follows.

Intake CMP sensor Condition Resistance
Terminal (Polarity)
1 2 Temperature [°C (°F)] 25 (77) Except 0 or ∞Ω
3
2 3

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace the malfunctioning intake CMP sensor. Refer to Exploded View.

P0365 Exhaust Camshaft Position Sensor Nissan Pathfinder 5th Gen

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0365 00

CAMSHAFT POSITION SENSOR B B1

(Camshaft position sensor “B” circuit bank 1)
Diagnosis condition Engine running at idle
Signal (terminal) Exhaust camshaft position sensor (bank 1) signal
Threshold
  • Exhaust camshaft position sensor signal is not inputted to ECM

  • Exhaust camshaft position sensor signal is inappropriate or partly missing

Diagnosis delay time 1 second or more

POSSIBLE CAUSE

  • Harness or connectors [Exhaust camshaft position sensor (bank 1) circuit is open or shorted.]

  • Exhaust camshaft position sensor (bank 1)

  • Exhaust camshaft (bank 1) (sensor rotor)

FAIL-SAFE

Fail safe modeNissan Pathfinder Vehicle behavior
Device fix mode
  • Fixes electric intake valve timing control motor in the reference position.

  • Fixes exhaust valve timing control solenoid valve in the reference position.

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

  • Ignition switch ON: More than 11 V

  • Engine cranking: More than 7 V

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON.

  2. Shift the selector lever in N range.

  3. Start the engine and let it idle at least 5 seconds.

  4. Check DTC.

Is DTC P0365 detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK EXHAUST CAMSHAFT POSITION (CMP) SENSOR (BANK 1) POWER SUPPLY

  1. Turn ignition switch OFF.

  2. Disconnect exhaust CMP sensor (bank 1) harness connector.

  3. Turn ignition switch ON.

  4. Check the voltage between exhaust CMP sensor (bank 1) harness connector and ground.

    +−

    Voltage

    (Approx.)
    Exhaust CMP sensor (bank 1)
    ConnectorTerminal
    F43 1 Ground 5 V

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 2.

CHECK EXHAUST CMP SENSOR (BANK 1) POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF

  2. Disconnect ECM harness connector.

  3. Check the continuity between exhaust CMP sensor (bank 1) harness connector and ECM harness connector.

    Exhaust CMP sensor (bank 1)ECMContinuity
    ConnectorTerminalConnectorTerminal
    F43 1 F78 38 Existed
  4. Also check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

Perform the trouble diagnosis for ECM power supply circuit.

NO>>

Repair or replace error-detected parts.

CHECK EXHAUST CMP SENSOR (BANK 1) GROUND CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between exhaust CMP sensor (bank 1) harness connector and ECM harness connector.

    Exhaust CMP sensor (bank 1)ECMContinuity
    ConnectorTerminalConnectorTerminal
    F43 2 F78 28 Existed
  4. Also check harness for short to power.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace error-detected parts.

CHECK EXHAUST CMP SENSOR (BANK 1) INPUT SIGNAL CIRCUIT

  1. Check the continuity between exhaust CMP sensor (bank 1) harness connector and ECM harness connector.

    Exhaust CMP sensor (bank 1)ECMContinuity
    ConnectorTerminalConnectorTerminal
    F43 3 F78 34 Existed
  2. Also check harness for short to power and short to ground.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Repair or replace error-detected parts.

CHECK EXHAUST CMP SENSOR (BANK 1)

Check exhaust CMP sensor (bank 1). Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Replace exhaust CMP sensor (bank 1). Refer to Exploded View.

CHECK EXHAUST CAMSHAFT (BANK 1)

Check the following items:

  • Accumulation of debris to the signal plate exhaust camshaft (bank 1) rear end

  • Chipping signal plate of camshaft rear end

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Remove debris and clean the signal plate of the camshaft rear end or replace the camshaft. Refer to Removal and Installation.

Component Inspection

CHECK EXHAUST CAMSHAFT POSITION (CMP) SENSOR-I

  1. Turn ignition switch OFF.

  2. Disconnect exhaust CMP sensor harness connector.

  3. Remove the sensor. Refer to Exploded View.

  4. Visually check the sensor for chipping.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace the malfunctioning exhaust CMP sensor. Refer to Exploded View.

CHECK EXHAUST CMP SENSOR-II

Check resistance exhaust CMP sensor terminals as follows.

Exhaust CMP sensorConditionResistance
Terminal (Polarity)
1 2 Temperature [°C (°F)] 25 (77) Except 0 or ∞Ω
3
2 3

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace the malfunctioning exhaust CMP sensor. Refer to Exploded View.

P0385 Ckp Sensor 2 Nissan Pathfinder R53

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0385 00

CKP SENSOR B

(Crankshaft Position Sensor "B" Circuit)
Diagnosis condition Engine running
Signal (terminal) Crankshaft position sensor 2 signal
Threshold The proper pulse signal from the crankshaft position sensor 2 is not sent to ECM while the engine is running.
Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors

    (Crankshaft position sensor 2 circuit is open or shorted.)

  • Crankshaft position sensor 2

FAIL-SAFE

Engine Control System

Not applicable

Stop/start System

When a DTC is detected, the stop/start indicator blinks slowly and the stop/start system operation is prohibited.

When ECM detects error while operating the stop/start system, ECM restarts the engine.

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 10.5 V at idling.

>>

GO TO 2.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and let it idle for at least 5 seconds.

    If engine does not start, crank engine for at least 2 seconds.

  2. Check 1st trip DTC.

Is DTC detected?

YES>>

Refer to DTC Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

DTC Diagnosis Procedure

CHECK CRANKSHAFT POSITION SENSOR 2 POWER SUPPLY-1

  1. Turn ignition switch OFF

  2. Disconnect crankshaft position sensor 2 harness connector.

  3. Turn ignition switch ON.

  4. Check the voltage between crankshaft position sensor 2 harness connector terminal.

Crankshaft position sensor 2Condition

Voltage

(Approx.)
Connector+−
Terminal
F91 1 2 Ignition switch ON 5 V
Ignition switch OFF 0 V

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

GO TO 4.

CHECK CRANKSHAFT POSITION SENSOR 2 SIGNAL CIRCUIT

  1. Turn ignition switch OFF

  2. Disconnect ECM harness connector.

  3. Check the continuity between crankshaft position sensor 2 harness connector and ECM harness connector.

    +−Continuity
    Crankshaft position sensor 2ECM
    ConnectorTerminalConnectorTerminal
    F91 3 F78 74 Existed
  4. Also check harness for short to ground.

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace error-detected parts.

CHECK CRANKSHAFT POSITION SENSOR 2

Check crankshaft position sensor 2. Refer to Component Inspection (Crankshaft Position Sensor 2).

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Repair or replace error-detected parts.

CHECK CRANKSHAFT POSITION SENSOR 2 POWER SUPPLY-2

Check the continuity between crankshaft position sensor 2 harness connector and ground.

+−Condition

Voltage

(Approx.)
Crankshaft position sensor 2
ConnectorTerminal
F91 1 Ground Ignition switch ON 5 V
Ignition switch OFF 0 V

Is the inspection result normal?

YES>>

GO TO 5 .

NO>>

GO TO 6.

CHECK CRANKSHAFT POSITION SENSOR 2 GROUND CIRCUIT

  1. Turn ignition switch OFF

  2. Disconnect ECM harness connector.

  3. Check the continuity between crankshaft position sensor 2 harness connector and ECM harness connector.

+−Continuity
Crankshaft position sensor 2ECM
ConnectorTerminalConnectorTerminal
F91 2 F78 77 Existed

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Repair or replace error-detected parts.

CHECK CRANKSHAFT POSITION SENSOR 2 POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF

  2. Disconnect ECM harness connector.

  3. Check the continuity between crankshaft position sensor 2 harness connector and ECM harness connector.

+−Continuity
Crankshaft position sensor 2ECM
ConnectorTerminalConnectorTerminal
F91 1 F78 63 Existed

Is the inspection result normal?

YES>>

Check intermittent incident. Refer to Intermittent Incident.

NO>>

Repair or replace error-detected parts.

P0420 Three Way Catalyst Function Nissan Pathfinder R53

DTC Description

The ECM monitors the switching frequency ratio of air fuel ratio (A/F) sensor 1 and heated oxygen sensor 2.

A three way catalyst 1 with high oxygen storage capacity will indicate a low switching frequency of heated oxygen sensor 2. As oxygen storage capacity decreases, the heated oxygen sensor 2 switching frequency will increase.

When the frequency ratio of A/F sensor 1 and heated oxygen sensor 2 approaches a specified limit value, the three way catalyst 1 malfunction is diagnosed.

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0420 00

TW CATALYST SYS-B1

(Catalyst system efficiency below threshold bank 1)
Diagnosis condition —
Signal (terminal) —
Threshold
  • Three way catalyst (manifold) does not operate properly

  • Three way catalyst (manifold) does not have enough oxygen storage capacity

Diagnosis delay time —

POSSIBLE CAUSE

  • Three way catalyst (manifold)

  • Exhaust tube

  • Intake air leaks

  • Fuel injector

  • Fuel injector leaks

  • Spark plug

  • Improper ignition timing

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

INSPECTION START

Do you have CONSULT?

YES>>

GO TO 2.

NO>>

GO TO 7.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Do not hold engine speed for more than the specified minutes below.

>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE-I

With CONSULT

  1. Turn ignition switch ON.

  2. On CONSULT screen, select “ENGINE”>>“Data Monitor”.

  3. Start engine and warm it up to the normal operating temperature.

  4. Turn ignition switch OFF and wait at least 10 seconds.

  5. Turn ignition switch ON.

  6. Turn ignition switch OFF and wait at least 10 seconds.

  7. Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1 minute under no load.

  8. Let engine idle for 1 minute.

  9. Make sure that “COOLAN TEMP/S” indicates more than 70 °C.

    If not, warm up engine and go to next step when “COOLAN TEMP/S” indication reaches 70 °C.

  10. Open engine hood.

  11. On CONSULT screen, select “DTC & SRT CONFIRMATION”>>“SRT WORK SUPPORT”.

  12. Rev engine up to about 2,000 rpm and hold it for 3 consecutive minutes then release the accelerator pedal completely.

  13. Check the indication of “CATALYST”.

Which is displayed on CONSULT screen?

CMPLT>>

GO TO 6.

INCMP>>

GO TO 4.

PERFORM DTC CONFIRMATION PROCEDURE-II

  1. Wait 5 seconds at idle.

  2. Rev engine up to about 2,000 rpm and maintain it until “INCMP” of “CATALYST” changes to “CMPLT” (It will take approximately 5 minutes).

Does the indication change to “CMPLT”?

YES>>

GO TO 6.

NO>>

GO TO 5.

PERFORM DTC CONFIRMATION PROCEDURE AGAIN

  1. Stop engine and cool it down to less than 70 °C.

  2. Perform DTC CONFIRMATION PROCEDURE again.

>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE-III

Check 1st trip DTC.

Is DTC P0420 detected?

YES>>

Proceed to Diagnosis Procedure.

NO-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO-2>>

Confirmation after repair: INSPECTION END

PERFORM COMPONENT FUNCTION CHECK

Without CONSULT

  1. Start engine and warm it up to the normal operating temperature.

  2. Turn ignition switch OFF and wait at least 10 seconds.

  3. Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1 minute under no load.

  4. Let engine idle for 1 minute.

  5. Open engine hood.

  6. Check the voltage between ECM harness connector terminals under the following condition.

    ECM Condition Voltage
    Connector + –
    Terminal
    F78

    49

    [HO2S2 (bank 1)]
    81 Keeping engine speed at 2,500 rpm constant under no load

    The voltage fluctuation cycle takes more than 5 seconds.

    • 1 cycle: 0.6 - 1.0 → 0 - 0.3 → 0.6 - 1.0

Is the inspection result normal?

YES-1>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

YES-2>>

Confirmation after repair: INSPECTION END

NO>>

Proceed to Diagnosis Procedure.

Diagnosis Procedure

CHECK EXHAUST SYSTEM

Visually check exhaust tubes and muffler for dents.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace.

CHECK EXHAUST GAS LEAK

  1. Start engine and run it at idle.

  2. Listen for an exhaust gas leak before the three way catalyst 1.

Is exhaust gas leak detected?

YES>>

Repair or replace.

NO>>

GO TO 3.

CHECK INTAKE AIR LEAK

Listen for an intake air leak after the mass air flow sensor.

Is intake air leak detected?

YES>>

Repair or replace.

NO>>

GO TO 4.

CHECK IDLE SPEED AND IGNITION TIMING

For procedure, refer to Work Procedure.

For specification, refer to Idle Speed and Ignition Timing.

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Follow the Work Procedure.

CHECK FUEL INJECTORS

Check the fuel injector. Refer to Component Function Check.

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Perform Diagnosis Procedure.

CHECK FUNCTION OF IGNITION COIL-I

  1. Turn ignition switch OFF.

  2. Pull out 20A fuse (No.85) from IPDM E/R to release fuel pressure. Refer to IPDM E/R Terminal Arrangement .

  3. Start engine.

  4. After engine stalls, crank it two or three times to release all fuel pressure.

  5. Turn ignition switch OFF.

  6. Remove all ignition coil harness connectors to avoid the electrical discharge from the ignition coils.

  7. Remove ignition coil and spark plug of the cylinder to be checked.

  8. Crank engine for 5 seconds or more to remove combustion gas in the cylinder.

  9. Connect spark plug and harness connector to ignition coil.

  10. Fix ignition coil using a rope etc. with gap of 13 – 17 mm (0.52 – 0.66 in) between the edge of the spark plug and grounded metal portion as shown in the figure.

  11. Crank engine for about 3 seconds, and check whether spark is generated between the spark plug and the grounded metal portion.

    Spark should be generated.

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

GO TO 7.

CHECK FUNCTION OF IGNITION COIL-II

  1. Turn ignition switch OFF.

  2. Disconnect spark plug and connect a non-malfunctioning spark plug.

  3. Crank engine for about 3 seconds, and recheck whether spark is generated between the spark plug and the grounded metal portion.

    Spark should be generated.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Check ignition coil, power transistor and their circuits. Refer to Diagnosis Procedure.

CHECK SPARK PLUG

Check the initial spark plug for fouling, etc.

Is the inspection result normal?

YES>>

Replace spark plug(s) with standard type one(s). For spark plug type, refer to Spark Plug.

NO>>

Repair or clean spark plug. Then GO TO 9.

CHECK FUNCTION OF IGNITION COIL-III

  1. Reconnect the initial spark plugs.

  2. Crank engine for about three seconds, and recheck whether spark is generated between the spark plug and the grounded portion.

    Spark should be generated.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace spark plug(s) with standard type one(s). For spark plug type, refer to Spark Plug.

PERFORM DTC CONFIRMATION PROCEDURE

  1. Replace three way catalyst of malfunctioning bank side. Refer to Removal and Installation (bank 2), Removal and Installation (bank 1).

  2. Perform DTC confirmation procedure. Refer to DTC Description.

Is DTC P0420 detected?

YES>>

Replace all fuel injector of malfunctioning bank side. Refer to Removal and Installation

NO>>

INSPECTION END