Starting System - Dtc/circuit Diagnosis
- B Terminal Circuit
- S Terminal Circuit
- Stop/start Off Switch Circuit
B Terminal Circuit Nissan Pathfinder
Diagnosis Procedure
Terminal “B” is constantly supplied with battery power.
Remove fuel pump fuse.
Crank or start the engine (where possible) until the fuel pressure is released.
CHECK “B” TERMINAL CIRCUIT
Ignition switch OFF.
Make sure that starter motor "B" terminal connection is clean and tight.
Check voltage between starter motor ”B” terminal and ground.
(+) (—) Voltage
(Approx.)Starter motor Connector Terminal F27 B Ground Battery voltage
Is the inspection result normal?
YES>>GO TO 2.
NO>>Check harness between battery and starter motor for open circuit.
CHECK BATTERY CABLE CONNECTION STATUS (VOLTAGE DROP TEST)
Shift selector lever to ”P” (Park) or ”N” (Neutral) position.
Check voltage between battery positive terminal and starter motor ”B” terminal.
| (+) | (—) | Condition | Voltage (Approx.) | |
|---|---|---|---|---|
| Starter motor | ||||
| Connector | Terminal | |||
| Battery positive terminal | F27 | B | When the ignition switch is in START position | Less than 0.5V |
Is the inspection result normal?
YES>>GO TO 3.
NO>>Check harness between the battery and starter motor for continuity.
CHECK GROUND CIRCUIT STATUS (VOLTAGE DROP TEST)
Shift selector lever to ”P” (Park) or ”N” (Neutral) position.
Check voltage between starter motor case and battery negative terminal.
(+) (—) Condition Voltage
(Approx.)Starter motor case Battery negative terminal When the ignition switch is in START position Less than 0.2V
Is the inspection result normal?
YES>>“B” terminal circuit is OK. Further inspection is necessary. Refer to Work Flow (With 165-DSS-5000P) or Work Flow (Without 165-DSS-5000P).
NO>>Check the starter motor case to engine mounting for high resistance.
S Terminal Circuit Nissan Pathfinder
Diagnosis Procedure
The starter motor magnetic switch is supplied with power when the ignition switch is in the START position while the selector lever is in the P (Park) or N (Neutral) position.
Remove fuel pump fuse.
Crank or start the engine (where possible) until the fuel pressure is released.
CHECK “S” TERMINAL CIRCUIT
Ignition switch OFF.
Disconnect starter motor connector.
Shift selector lever to “P” (Park) or “N” (Neutral) position.
Check voltage between starter motor harness connector and ground.
(+) (—) Condition Voltage
(Approx.)Starter motor Connector Terminal F28 S Ground When the ignition switch is in START position Battery voltage
Is the inspection result normal?
YES>>“S” circuit is OK. Further inspection is necessary. Refer to Work Flow (With 165-DSS-5000P) or Work Flow (Without 165-DSS-5000P).
NO>>GO TO 2.
CHECK HARNESS CONTINUITY (OPEN CIRCUIT)
Disconnect IPDM E/R connector.
Check continuity between starter motor harness connector and the IPDM E/R harness connector.
Starter motor IPDM E/R Continuity Connector Terminal Connector Terminal F28 S E77 83 Yes Check continuity between starter motor terminal S and ground.
Starter motor — Continuity Connector Terminal F28 S Ground No
Is the inspection result normal?
YES>>Further inspection is necessary. Refer to Work Flow (With 165-DSS-5000P) or Work Flow (Without 165-DSS-5000P).
NO>>Repair or replace the harness or connectors.
Stop/start Off Switch Circuit Nissan Pathfinder
Component Function Check
CHECK STOP/START OFF SWITCH SIGNAL
CONSULT
Ignition switch ON.
Select “INTELLIGENT KEY” of “BCM”.
Select “STOP/START SW” in “Data Monitor” mode.
With operating the stop/start off switch, check the monitor status.
Monitor item Condition Monitor status STOP/START SW Stop/start off switch ON On OFF Off
Is the inspection result normal?
YES>>Stop/start off switch circuit is normal.
NO>>Refer to Diagnosis Procedure.
Diagnosis Procedure
CHECK STOP/START OFF SWITCH SIGNAL
Ignition switch OFF.
Disconnect stop/start off switch connector.
Check voltage between stop/start off switch connector and ground.
(+) (—) Voltage
(Approx.)Stop/start off switch Connector Terminal M224 6 Ground Battery voltage
Is the inspection result normal?
YES>>GO TO 4.
NO>>GO TO 2.
CHECK STOP/START OFF SWITCH SIGNAL CIRCUIT (OPEN)
Disconnect BCM connector.
Check continuity between stop/start off switch harness connector and BCM harness connector.
Stop/start off switch BCM Continuity Connector Terminal Connector Terminal M224 6 M18 20 Yes
Is the inspection result normal?
YES>>GO TO 3.
NO>>Repair or replace harness.
CHECK STOP/START OFF SWITCH SIGNAL CIRCUIT (SHORT)
Check continuity between stop/start off switch harness connector and ground.
| Stop/start off switch | — | Continuity | |
|---|---|---|---|
| Connector | Terminal | ||
| M224 | 6 | Ground | No |
Is the inspection result normal?
YES>>Replace BCM. Refer to Removal and Installation.
NO>>Repair or replace harness.
CHECK STOP/START OFF SWITCH GROUND CIRCUIT
Check continuity between stop/start off switch harness connector and ground.
| Stop/start off switch | — | Continuity | |
|---|---|---|---|
| Connector | Terminal | ||
| M224 | 8 | Ground | Yes |
Is the inspection result normal?
YES>>GO TO 5.
NO>>Repair or replace harness.
CHECK STOP/START OFF SWITCH
Check stop/start off switch. Refer to Component Inspection.
Is the inspection result normal?
YES>>Inspection End.
NO>>Replace stop/start off switch. Refer to Removal and Installation.
Component Inspection
CHECK STOP/START OFF SWITCH
Ignition switch OFF.
Disconnect stop/start off switch connector.
Check continuity of stop/start off switch terminals.
Stop/start off switch Condition Continuity Terminals (+) (—) 6 8 Stop/start off switch ON Yes OFF No
Is the inspection result normal?
YES>>Inspection End.
NO>>Replace stop/start off switch. Refer to Removal and Installation.